UHP201610NF-100M

TAI-TECH P1 Power Inductor UHP201610NF-SERIES ECN HISTORY LIST REV DATE DESCRIPTION APPROVED CHECKED DRAWN 1.0 14/06/20 新 發 行 楊祥忠 詹偉特 林宜蕰 備 註 www.tai-tech.com.tw TAI-TECH P2 Power Inductor UHP201610NF-SERIES 1. Features 1. This specification n applies Low Profile Power Inductors. 2. 100% Lead(Pb) & Halogen-Free and RoHS compliant. 2. Dimension Halogen Pb Halogen-free Pb-free B A D E D C Series A(mm) B(mm) UHP201610NF 2.0 -0.1/+0.2 C(mm) 1.6 -0.1/+0.2 D(mm) E(mm) 1.0max. 0.60 ref. 0.80 ref. Units: mm 3. Part Numbering UHP 201610 NF A B A: Series B: Dimension C: Lead Free D: Inductance E: Inductance Tolerance - C 4R7 M D E Material 4R7=4.7uH M=±20%；Y=±30% 4. Specification TAI-TECH Part Number Inductance (uH) Tolerance (%) Test Frequency (Hz) DCR (Ω) ±20% I sat (A) typ. I sat (A) Max. I rms (A) typ. I rms (A) Max. UHP201610NF-R47Y 0.47 ±30% 0.1V/1M 0.044 3.00 2.70 2.60 2.35 UHP201610NF-R68Y 0.68 ±30% 0.1V/1M 0.062 2.45 2.00 2.25 2.05 UHP201610NF-1R0Y 1.0 ±30% 0.1V/1M 0.080 1.95 1.80 1.75 1.60 UHP201610NF-1R5Y 1.5 ±30% 0.1V/1M 0.130 1.65 1.46 1.40 1.26 0.145 1.45 1.26 1.35 1.20 0.245 1.05 0.90 1.05 0.95 0.360 0.85 0.77 1.00 0.90 UHP201610NF-2R2M UHP201610NF-3R3M UHP201610NF-4R7M 2.2 3.3 4.7 ±20% ±20% ±20% 0.1V/1M 0.1V/1M 0.1V/1M UHP201610NF-6R8M 6.8 ±20% 0.1V/1M 0.500 0.80 0.72 0.70 0.55 UHP201610NF-100M 10 ±20% 0.1V/1M 0.720 0.62 0.55 0.50 0.45 UHP201610NF-150M 15 ±20% 0.1V/1M 1.400 0.50 0.45 0.40 0.36 UHP201610NF-180M 18 ±20% 0.1V/1M 1.800 0.45 0.40 0.38 0.34 UHP201610NF-220M 22 ±20% 0.1V/1M 2.000 0.43 0.38 0.30 0.27 Note: Isat：Based on inductance change （△L/L0：≦-30%）@ ambient temp. 25℃ Irms：Based on temperature rise （△T：40℃.） www.tai-tech.com.tw TAI-TECH P3 UHP201610NF-R47 0.8 1.2 Inductance(uH) Inductance(uH) 0.6 0.4 0.9 0.6 0.2 0 UHP201610NF-R68 1.5 0.3 0 0.5 1 1.5 2 DCcurrent(A) 2.5 3 0 3.5 UHP201610NF-1R0 2 0 0.5 1 1.5 2 DCcurrent(A) 2.5 UHP201610NF-1R5 3 2.5 2 Inductance(uH) Inductance(uH) 1.5 1 1.5 1 0.5 0.5 0 0 0.5 1 1.5 DCcurrent(A) 2 0 2.5 UHP201610NF-2R2 4 0 0.5 1 1.5 DCcurrent(A) 2 UHP201610NF-3R3 6 5 Inductance(uH) Inductance(uH) 3 2 4 3 2 1 1 0 0 0.3 0.6 0.9 DCcurrent(A) 1.2 0 1.5 UHP201610NF-4R7 10 0.6 0.9 DCcurrent(A) 1.2 UHP201610NF-6R8 9 Inductance(uH) Inductance(uH) 0.3 12 8 6 4 6 3 2 0 0 0 0.2 0.4 0.6 DCcurrent(A) 0.8 1 0 www.tai-tech.com.tw 0 0.2 0.4 0.6 DCcurrent(A) 0.8 1 TAI-TECH P4 UHP201610NF-100 20 20 Inductance(uH) Inductance(uH) 15 10 15 10 5 0 5 0 0.2 0.4 DCcurrent(A) 0.6 0 0.8 UHP201610NF-180 30 0.2 0.4 0.6 DCcurrent(A) 0.8 UHP201610NF-220 28 Inductance(uH) Inductance(uH) 0 35 24 18 12 6 0 UHP201610NF-150 25 21 14 7 0 0.1 0.2 0.3 DCcurrent(A) 0.4 0.5 0 0 0.1 0.2 0.3 DCcurrent(A) 0.4 Void appearance tolerance Limit Size of voids occurring to coating resin is specified below. Exposed wire tolerance limit of coating resin part on product side. Size of exposed wire occurring to coating resin is specified below. ：Acceptable when a≦w/2 1. Width direction（dimension a） Nonconforming when a＞w/2 2. Length direction（dimension b）：Dimension b is not specified. 3. The total area of exposed wire occurring to each sides is not greater than 50% of coating resin area, and is acceptable. External appearance criterion for exposed wire Exposed end of the winding wire at the secondary side should be 2mm and below. www.tai-tech.com.tw 0.5 TAI-TECH P5 5. Material No. Description Specification a. Core Ferrite Core b. Coating Epoxy with magnetic powder c Termination Tin (Pb Free) d Wire Enameled Copper Wire 6. Reliability and Test Condition Item Operating Temperature Performance Test Condition -40~+125℃ Storage Temperature (on board) Electrical Performance Test Inductance L Agilent-4291, Agilent-4287 Refer to standard electrical characteristic list DC Resistance Rated Current Temperature Rise Test Agilent-4338 Base on temp. rise & △L/L0A≦30%. Saturation DC Current (Isat) will cause L0 to drop approximately △L(%). ΔT 40℃Max Heat Rated Current (Irms) will cause the coil temperature rise approximately △T(℃) without core loss. 1.Applied the allowed DC current. 2.Temperature measured by digital surface thermometer Mechanical Performance Test Appearance：No damage. Solder Heat Resistance Temperature (°C) Time (s) Temperature ramp/immersion and emersion rate 260 ±5 (solder temp) 10 ±1 25mm/s±6 mm/s Inductance：within±10% of initial value RDC：within ±15% of initial value and shall not exceed the specification value Depth: completely cover the termination www.tai-tech.com.tw Number of heat cycles 1 TAI-TECH P6 Item Solderability Test Performance Test Condition Preheat: 150℃,60sec.。 Solder: Sn99.5%-Cu0. 5%。 Temperature: 245±5℃。 Flux for lead free: Rosin. 9.5%。 More than 95% of terminal electrode should be covered with solder. Dip time: 4±1sec。 Depth: completely cover the termination Reliability Test Preconditioning:Run through IR reflow for 2 times.( IPC/JEDEC J-STD-020DClassification Reflow Profiles Temperature：125±2℃(Bead) Life Test Temperature： 85±2℃(Inductor) Applied current：rated current Duration：1000±12hrs Measured at room temperature after placing for 24±2 hrs Preconditioning:Run through IR reflow for 2 times.( IPC/JEDEC J-STD-020DClassification Reflow Profiles Step1：-40±2℃ 30±5min Thermal shock Step2：25±2℃ ≦0.5min Appearance：No damage. Step3：105±2℃ 30±5min Inductance：within±10% of initial value Number of cycles： 500 Measured at room fempraturc after placing for 24±2 hrs RDC：within ±15% of initial value and shall not exceed the specification value Preconditioning:Run through IR reflow for 2 times.( IPC/JEDEC J-STD-020DClassification Reflow Profiles Humidity：85±2﹪R.H, Humidity Resistance Test Temperature：85℃±2℃ Duration：1000hrs Min. with 100% rated current Measured at room temperature after placing for 24±2 hrs Preconditioning:Run through IR reflow for 2 times.( IPC/JEDEC J-STD-020DClassification Reflow Profiles Oscillation Frequency: 10～2K～10Hz for 20 minutes Equipment： Vibration checker Total Amplitude:1.52mm±10% Testing Time : 12 hours(20 minutes, 12 cycles each of 3 orientations)。 Vibration Test www.tai-tech.com.tw TAI-TECH P7 7. Soldering and Mounting 7-1. Soldering Mildly activated rosin fluxes are preferred. TAI-TECH terminations are suitable for all wave and re-flow soldering systems. If hand soldering cannot be avoided, the preferred technique is the utilization of hot air soldering tools. 7-1.1 Solder re-flow: Recommended temperature profiles for re-flow soldering in Figure 1. 7-1.2 Soldering Iron(Figure 2): Products attachment with a soldering iron is discouraged due to the inherent process control limitations. In the event that a soldering iron must be employed the following precautions are recommended. ‧Preheat circuit and products to 150℃ ‧355℃ tip temperature (max) ‧Never contact the ceramic with the iron tip ‧1.0mm tip diameter (max) Iron Soldering Reflow Soldering PRE-HEATING SOLDERING 20~40s PRE-HEATING NATURAL COOLING TEMPERATURE(¢X C) TEMPERATURE(¢X C) 217 SOLDERING within 4~5s TP(260¢X C / 40s max.) 200 150 ‧Use a 20 watt soldering iron with tip diameter of 1.0mm ‧Limit soldering time to 4~5 sec. 60~150s 60~180s 350 150 Gradual cooling Over 60s 480s max. 25 TIM E(sec.) TIME( sec.) Reflow times: 3 times max. Iron Soldering times: 1 times max. Fig.1 Fig.2 7-2. Recommended PC Board Pattern L H NATURAL COOLING L(mm) G(mm) H(mm) 2.3 0.7 1.7 G www.tai-tech.com.tw TAI-TECH P8 8. Packaging Information 8-1. Reel Dimension C B D A Type A(mm) B(mm) C(mm) D(mm) 7”x8mm 8.4±1.0 50 min. 13±0.8 178±2 7"x8mm 8-2. Tape Dimension / 8mm t P Ao Bo Po:4∮0.1 W:8.0∮0.1 P2:2∮0.05 Series Size UHP 201610 Bo(mm) Ao(mm) Ko(mm) P(mm) 2.5±0.10 2.0±0.10 1.05±0.10 4.0±0.10 0.23±0.05 Ko 8-3. Packaging Quantity Chip size 201610 Chip / Reel 2000 8-4. Tearing Off Force F Top cover tape The force for tearing off cover tape is 15 to 80 grams in the arrow direction under the following conditions. 165¢Xto180¢X Base tape Room Temp. Room Humidity Room atm Tearing Speed (℃) (%) (hPa) mm/min 5~35 45~85 860~1060 300 Application Notice ‧Storage Conditions(component level) To maintain the solderability of terminal electrodes: 1. TAI-TECH products meet IPC/JEDEC J-STD-020D standard-MSL, level 1. 2. Temperature and humidity conditions: Less than 40℃ and 60% RH. 3. Recommended products should be used within 12 months form the time of delivery. 4. The packaging material should be kept where no chlorine or sulfur exists in the air. ‧Transportation 1. Products should be handled with care to avoid damage or contamination from perspiration and skin oils. 2. The use of tweezers or vacuum pick up is strongly recommended for individual components. 3. Bulk handling should ensure that abrasion and mechanical shock are minimized. www.tai-tech.com.tw t(mm)