SAMXON
A L U M I N U M E L E C T R O LY T I C C A PA C I T O R S
2017-2018
Contents (目錄)
Series Chart 產品體系圖
Series Table 產品一覽表
Application Guidelines 應用指引
Index
002
004
006
015
016
017
018
Part Number System 產品編碼
Taping Specifications 編帶產品規格
Packing Specifications 包裝規格
Lead Forming Specifications 成型產品規格
Miniature Aluminum Electrolytic Capacitors 小型鋁電解電容器
Miniature
Miniature Type 小型品
General Purpose 普通品
Low Impedance Type 低阻抗品
High Reliability Type 高可靠品
High Temperature Type 高溫度品
For Audio Type 音響用品
Non-polarized Type 無極性品
Large Can Aluminum Electrolytic Capacitors 大型鋁電解電容器
093
095
113
146
147
Lug / Snap-in Terminal Type Case Size Table 插入/自立型產品圖解
Lug / Snap-in Terminal Standard Type 插入/自立型標准品
Large Can
Pen Cap Type 筆型電容
Lug / Snap-in Terminal High Reliability Type 插入/自立型高可靠品
Screw Terminal Type Case Size Table 螺釘型產品圖解
Screw Terminal Type 螺釘型
V-Chip Aluminum Electrolytic Capacitors 貼片式鋁電解電容器
178
Surface Mount Type Packing Specifications 貼片品包裝規格
179
Surface Mount Type 貼片品
V-Chip
019
023
034
061
072
081
083
087
1
Series Chart (產品體系圖)
導針型
Radial Lead Type
Low Impedance
SK
P.47
SH
P.45
GK
P.43
Index
-40 ~ +105˚C
6,000 ~ 10,000 Hrs
Highest Ripple Current
Lower Impedance
Longest Life
-40 ~ +105˚C
5,000 ~ 6,000 Hrs
Highest Ripple Current
Lowest Impedance
Long Life
-40 ~ +105˚C
2,000 ~ 5,000 Hrs
Higher Ripple Current
Lower Impedance
GF
Miniaturization
KF
P.19
-40 ~ +105˚C
1,000 Hrs
5mmL
KS
P.34
P.21
RF
P.57
-55 ~ +105˚C
1,000 ~ 4,000 Hrs
Wide Temperature
High Ripple Current
Low Impedance
-40 ~ +105˚C
1,000 Hrs
7mmL
P.23
-40(-25) ~ +85˚C
2,000 Hrs
General
KM
P.26
RR
P.61
-40(-25) ~ +105˚C
3,000 Hrs
Long Life
High Ripple Current
P.30
-55 ~ +105˚C
1,000 ~ 2,000 Hrs
Wide Temperature
P.83
-40 ~ +85˚C
1,000 Hrs
Non-polar
NH
RE
P.66
-40 ~ +85˚C
1,000 Hrs
For Audio Standard
OM
P.85
KM
P.87
RT
P.63
RD
P.68
RH
P.70
-40(-25) ~ +105˚C
10,000 ~ 12,000 Hrs
Longest Life
High Ripple Current
RW
P.89
-25 ~ +105˚C
5,000 Hrs
Long Life
Pen Cap
-25 ~ +105˚C
2,000 Hrs
Pen Cap
RY
P.91
-25 ~ +105˚C
10,000 Hrs
Longer Life
Pen Cap
High Temperature
P.32
-25 ~ +105˚C
2,000 Hrs
Withstanding Overvoltage
BD
P.72
-40 ~ +125˚C
1,000 ~ 2,000 Hrs
High Temperature
RA
-40(-25) ~ +130˚C
1,000 ~ 4,000 Hrs
High Temperature
High Ripple Current
2
P.55
Pen Cap
-40 ~ +105˚C
1,000 Hrs
Non-polar
P.81
GY
-40 ~ +105˚C
4,000 ~ 10,000 Hrs
Longer Life
Low Impedance
-40(-25) ~ +105˚C
8,000 ~ 10,000 Hrs
Longer Life
High Ripple Current
-25 ~ +105˚C
8,000 ~ 10,000 Hrs
Longer Life
Special Type
FA
P.51
P.40
-40 ~ +105˚C
4,000 ~ 10,000 Hrs
High Ripple Current
Longer Life
Low Impedance
-40(-25) ~ +105˚C
5,000 Hrs
Long Life
High Ripple Current
Non-polar
NP
RS
GT
High Reliability
-40(-25) ~ +105˚C
2,000 Hrs
General
KG
P.38
-40 ~ +105˚C
3,000 ~ 7,000 Hrs
High Ripple Current
Longer Life
Low Impedance
General
GS
SF
-40 ~ +105˚C
3,000 ~ 6,000 Hrs
High Ripple Current
Long Life
Low Impedance
-40 ~ +105˚C
1,000 ~ 4,000 Hrs
High Ripple Current
Low Impedance
P.74
RB
-40(-25) ~ +130˚C
3,000 ~ 4,000 Hrs
High Temperature
High Ripple Current
Long Life
P.77
RC
-25 ~ +130˚C
5,000 ~ 6,000 Hrs
High Temperature
High Ripple Current
Longer Life
P.79
Series Chart (產品體系圖)
插入/自立型
Lug / Snap-in Terminal Type
General
TP
P.95
-40(-25) ~ +85˚C
2,000 Hrs
Standard
P.111
Index
LP
Long Life
-25 ~ +85˚C
10,000 Hrs
Ultra Long Life
HP
GP
P.113
-40(-25) ~ +105˚C
2,000 Hrs
Wide Temperature
KP
P.143
-40(-25) ~ +105˚C
2,000 Hrs
Ultra Small Size
EP
P.121
-40(-25) ~ +105˚C
3,000 Hrs
Long Life
P.127
-40(-25) ~ +105˚C
5,000 Hrs
Long Life
SP
P.134
-40(-25) ~ +105˚C
7,000 Hrs
Longer Life
Special Type
QP
VP
P.103
-40(-25) ~ +85˚C
2,000 Hrs
Withstanding Vibration
P.137
-40(-25) ~ +105˚C
2,000 Hrs
Withstanding Vibration
Low Impedance
AP
UP
P.101
-40 ~ +85˚C
1,000 Hrs
For Audio
DP
P.119
FP
P.109
-40(-25) ~ +85˚C
5,000 Hrs
Long Life
Low Impedance
-25 ~ +105˚C
2,000 Hrs
Withstanding Overvoltage
P.132
-40(-25) ~ +105˚C
5,000 Hrs
Long Life
Low Impedance
螺釘型
Screw Terminal Type
General
WR
Long Life
WI
P.147
-40(-25) ~ +85˚C
2,000 Hrs
Standard
WX
P.152
P.160
-25 ~ +85˚C
2,000 Hrs
High Ripple Current
-40(-25) ~ +85˚C
5,000 Hrs
Longer Life
WT
WF
P.155
-40(-25) ~ +105˚C
2,000 Hrs
Standard
WH
-25 ~ +85˚C
10,000 Hrs
Longer Life
P.169
High Temperature
WL
P.172
-25 ~ +85˚C
20,000 Hrs
Ultra Long Life
WB
P.175
-25 ~ +125˚C
3,000 Hrs
High Temperature
P.164
-40(-25) ~ +105˚C
5,000 Hrs
Long Life
貼片型
Surface Mount Type
Low Impedance
General
VS1
P.179
-40 ~ +85˚C
2,000 Hrs
General
Φ4 ~ Φ10
-55 ~ +105˚C
1,000 Hrs
General
Φ4 ~ Φ6.3
High Voltage
VTG
-25 ~ +105˚C
3,000 Hrs
High Voltage
Φ8 ~ Φ10
VT1
P.185
P.181
VTD
-55 ~ +105˚C
2,000 Hrs
Low Impedance
Φ6.3 ~ Φ10
P.183
VZ2
P.187
-55 ~ +105˚C
2,000 Hrs
Low Impedance
Φ4 ~ Φ10
Long Life
VTL
P.189
-40 ~ +105˚C
3,000 ~ 5,000 Hrs
Long Life
Φ4 ~ Φ10
3
Series Table (產品一覽表)
Series
Features (特點)
Letter Color
Sleeve Color
Temp. (˚C)
Voltage (VDC)
Cap. (μF)
Load Life
Page
小型鋁電解電容器
Miniature Aluminum Electrolytic Capacitors
小型品
Miniature Type
KF 5mmL (高), +105˚C
White (白)
Black (黑)
-40 ~ +105
4 ~ 50
3.3 ~ 330
1,000 Hrs.
KS 7mmL (高), -40˚C ~ +105˚C
White (白)
Black (黑)
-40 ~ +105
6.3 ~ 50
3.3 ~ 330
1,000 Hrs.
P.19
P.21
Index
普通品
General Purpose
GS +85˚C, General (普通品)
White (白)
Dark Blue (深藍)
-40(-25) ~ +85
6.3 ~ 450
2.2 ~ 22000
2,000 Hrs.
KM +105˚C, General (普通品)
White (白)
Black (黑)
-40(-25) ~ +105
6.3 ~ 450
0.47 ~ 33000
2,000 Hrs.
P.23
P.26
KG -55 ~ +105˚C, Wide Temperature (寬溫度)
White (白)
Black (黑)
-55 ~ +105
6.3 ~ 100
2.2 ~ 22000
1,000 ~ 2,000 Hrs.
P.30
OM +105˚C, Withstanding Overvoltage (耐過電壓品)
White (白)
Black (黑)
-25 ~ +105
200 & 400
22 ~ 330
2,000 Hrs.
P.32
低阻抗品
Low Impedance Type
+105˚C, High Ripple Current, Low Impedance
(高紋波, 低阻抗)
White (白)
Sea Green (海綠)
-40 ~ +105
6.3 ~ 100
3.3 ~ 4700
1,000 ~ 4,000 Hrs.
P.34
+105˚C, High Ripple Current, Long Life Assurance,
SF
Low Impedance (高紋波, 長壽命, 低阻抗)
White (白)
Black (黑)
-40 ~ +105
6.3 ~ 100
15 ~ 3900
3,000 ~ 6,000 Hrs.
P.38
Silver (銀)
Black (黑)
-40 ~ +105
6.3 ~ 100
15 ~ 3900
4,000 ~ 10,000 Hrs.
P.40
White (白)
Sea Green (海綠)
-40 ~ +105
6.3 ~ 25
100 ~ 3900
2,000 ~ 5,000 Hrs.
P.43
+105˚C, Highest Ripple Current, Lowest Impedance,
Long Life Assurance (更高紋波, 更低阻抗, 長壽命)
White (白)
Black (黑)
-40 ~ +105
6.3 ~ 50
100 ~ 8200
5,000 ~ 6,000 Hrs.
P.45
+105˚C, Highest Ripple Current, Longest Life Assurance,
SK
Lower Impedance (更高紋波, 更長壽命, 較低阻抗)
Silver（銀）
Black（黑）
–40 ~ +105
6.3 ~ 100
33 ~ 8200
6,000 ~ 10,000 Hrs
P47
+105˚C, High Ripple Current, Longer Life Assurance,
RS
Low Impedance (高紋波, 較長壽命, 低阻抗)
White (白)
Black (黑)
-40 ~ +105
6.3 ~ 100
15 ~ 4700
3,000 ~ 7,000 Hrs.
P.51
+105˚C, Longer Life Assurance, Low Impedance
(較長壽命, 低阻抗)
White (白)
Black (黑)
-40 ~ +105
6.3 ~ 100
3.3 ~ 15000
4,000 ~ 10,000 Hrs.
P.55
White (白)
Black (黑)
-55 ~ +105
6.3 ~ 100
22 ~ 4700
1,000 ~ 4,000 Hrs.
P.57
GF
GT
+105˚C, High Ripple Current, Longer Life Assurance,
Low Impedance (高紋波, 較長壽命, 低阻抗)
+105˚C, Higher Ripple Current, Lower Impedance
GK
(較高紋波, 較低阻抗)
SH
GY
-55 ~ +105˚C, Wide Temperature, High Ripple Current,
RF
Low Impedance (寬溫度, 高紋波, 低阻抗)
高可靠品
High Reliability Type
Long Life Assurance, High Ripple Current
RR
(長壽命, 高紋波)
White (白)
Black (黑)
-40(-25) ~ +105
160 ~ 450
1 ~ 220
3,000 Hrs.
P.61
Long Life Assurance, High Ripple Current
RT
(長壽命, 高紋波)
White (白)
Black (黑)
-40(-25) ~ +105
160 ~ 450
1 ~ 220
5,000 Hrs.
P.63
White (白)
Black (黑)
-25 ~ +105
160 ~ 450
1 ~ 220
8,000 ~ 10,000 Hrs.
P.66
RD
RE Longer Life Assurance (較長壽命)
Longer Life Assurance, High Ripple Current
(較長壽命, 高紋波)
White (白)
Black (黑)
-40(-25) ~ +105
160 ~ 500
1 ~ 330
8,000 ~ 10,000 Hrs.
P.68
RH
Longest Life Assurance, High Ripple Current
(更長壽命, 高紋波)
White (白)
Black (黑)
-40(-25) ~ +105
160 ~ 500
1 ~ 220
10,000 ~ 12,000 Hrs.
P.70
BD +125˚C, High Temperature (高溫度)
White (白)
Black (黑)
-40 ~ +125
10 ~ 50
3.3 ~ 3900
1,000 ~ 2,000 Hrs.
P.72
+130˚C, High Temperature, High Ripple Current
RA
(高溫度, 高紋波)
White (白)
Black (黑)
-40(-25) ~ +130
10 ~ 450
1 ~ 4700
1,000 ~ 4,000 Hrs.
P.74
+130˚C, High Temperature, High Ripple Current,
RB
Long Life Assurance (高溫度, 高紋波, 長壽命)
White (白)
Black (黑)
-40(-25) ~ +130
160 ~ 450
1.5 ~ 100
3,000 ~ 4,000 Hrs.
P.77
+130˚C, High Temperature, High Ripple Current,
RC
Longer Life Assurance (高溫度, 高紋波, 較長壽命)
White (白)
Black (黑)
-25 ~ +130
160 ~ 450
1.5 ~ 100
5,000 ~ 6,000 Hrs.
P.79
高温度品
High Temperature Type
音響用品
For Audio Type
Standard, For Audio
FA
(標準品, 音響電容)
White (白)
Coffee (咖啡)
-40 ~ +85
6.3 ~ 100
2.2 ~ 10000
1,000 Hrs.
NP +85˚C, Non-polar (無極性)
Black (黑)
Green (綠)
-40 ~ +85
6.3 ~ 100
2.2 ~ 6800
1,000 Hrs.
P.83
NH +105˚C, Non-polar (無極性)
White (白)
Black (黑)
-40 ~ +105
6.3 ~ 100
2.2 ~ 1000
1,000 Hrs.
P.85
White (白)
Black (黑)
-25 ~ +105
200 ~ 450
22 ~ 270
2,000 Hrs.
P.87
無極性品
Non-polarized Type
筆型電容
Pen Cap Type
KM +105˚C, Pen Cap (筆型電容)
P.81
RW
+105˚C, Pen Cap, Long Life Assurance
(筆型電容, 長壽命)
White (白)
Black (黑)
-25 ~ +105
200 ~ 450
22 ~ 220
5,000 Hrs.
P.89
RY
+105˚C, Pen Cap, Longer Life Assurance
(筆型電容, 較長壽命)
White (白)
Black (黑)
-25 ~ +105
200 ~ 450
22 ~ 220
10,000 Hrs.
P.91
大型鋁電解電容器
Large Can Aluminum Electrolytic Capacitors
標準品
Standard Type
LP
Lug / Snap-in Terminal Type, Standard
(插入/自立型, 標準品)
White (白)
Black (黑)
-40(-25) ~ +85
10 ~ 500
56 ~ 82000
2,000 Hrs.
P.95
AP
Lug / Snap-in Terminal Type, For Audio
(插入/自立型, 音響電容)
White (白)
Coffee (咖啡)
-40 ~ +85
16 ~ 100
680 ~ 10000
1,000 Hrs.
P.101
White (白)
Black (黑)
-40(-25) ~ +85
10 ~ 500
56 ~ 82000
2,000 Hrs.
P.103
Lug / Snap-in Terminal Type, Long Life Assurance,
Low Impedance (插入/自立型, 長壽命, 低阻抗)
White (白)
Black (黑)
-40(-25) ~ +85
160 ~ 450
47 ~ 2200
5,000 Hrs.
P.109
Lug / Snap-in Terminal Type, Ultra Long Life Assurance
TP
(插入/自立型, 超長壽命)
White (白)
Black (黑)
-25 ~ +85
200 ~ 450
56 ~ 2200
10,000 Hrs.
P.111
Lug / Snap-in Terminal Type, Withstanding Vibration
QP
(插入/自立型, 耐振動)
DP
4
Series Table (產品一覽表)
Features (特點)
Letter Color
Sleeve Color
Temp. (˚C)
Voltage (VDC)
Cap. (μF)
Load Life
Page
大型鋁電解電容器
Large Can Aluminum Electrolytic Capacitors
高可靠品
High Reliability Type
Lug / Snap-in Terminal Type, Wide Temperature
HP
(插入/自立型, 寬溫度)
White (白)
Black (黑)
-40(-25) ~ +105
10 ~ 500
47 ~ 56000
2,000 Hrs.
P.113
Lug / Snap-in Terminal Type, Withstanding
Overvoltage (插入/自立型, 耐過電壓品)
White (白)
Black (黑)
-25 ~ +105
200 ~ 450
56 ~ 1200
2,000 Hrs.
P.119
Lug / Snap-in Terminal Type, Long Life Assurance
KP
(插入/自立型, 長壽命)
White (白)
Black (黑)
-40(-25) ~ +105
10 ~ 450
47 ~ 56000
3,000 Hrs.
P.121
Lug / Snap-in Terminal Type, Long Life Assurance
EP
(插入/自立型, 長壽命)
White (白)
Black (黑)
-40(-25) ~ +105
10 ~ 450
82 ~ 47000
5,000 Hrs.
P.127
Lug / Snap-in Terminal Type, Long Life Assurance,
FP
Low Impedance (插入/自立型, 長壽命, 低阻抗)
Silver (銀)
Black (黑)
-40(-25) ~ +105
10 ~ 450
100 ~ 33000
5,000 Hrs.
P.132
UP
SP
Lug / Snap-in Terminal Type, Longer Life Assurance
(插入/自立型, 較長壽命)
White (白)
Black (黑)
-40(-25) ~ +105
160 ~ 450
39 ~ 2200
7,000 Hrs.
P.134
VP
Lug / Snap-in Terminal Type, Withstanding Vibration
(插入/自立型, 耐振動)
White (白)
Black (黑)
-40(-25) ~ +105
10 ~ 500
39 ~ 56000
2,000 Hrs.
P.137
GP
Lug / Snap-in Terminal Type, Ultra Small Size
(插入/自立型, 超小體積)
White (白)
Black (黑)
-40(-25) ~ +105
160 ~ 450
100 ~ 3300
2,000 Hrs.
P.143
螺釘型
Screw Terminal Type
+85˚C, Screw Terminal Type, Standard
WR
(螺釘型, 標準品)
Silver (銀)
Black (黑)
-40(-25) ~ +85
10 ~ 630
100 ~ 680000
2,000 Hrs.
P.147
WI
+85˚C, Screw Terminal Type, High Ripple Current
(螺釘型, 高紋波)
Silver (銀)
Black (黑)
-25 ~ +85
350 ~ 450
390 ~ 22000
2,000 Hrs.
P.152
WT
+105˚C, Screw Terminal Type, Standard
(螺釘型, 標準品)
Silver (銀)
Black (黑)
-40(-25) ~ +105
10 ~ 500
180 ~ 680000
2,000 Hrs.
P.155
WX
+85˚C, Screw Terminal Type, Long Life Assurance
(螺釘型, 長壽命)
Silver (銀)
Black (黑)
-40(-25) ~ +85
10 ~ 550
1000 ~ 1500000
5,000 Hrs.
P.160
WF
+105˚C, Screw Terminal Type, Long Life Assurance
(螺釘型, 長壽命)
Silver (銀)
Black (黑)
-40(-25) ~ +105
10 ~ 500
330 ~ 390000
5,000 Hrs.
P.164
WH
+85˚C, Screw Terminal Type, Longer Life Assurance
(螺釘型, 較長壽命)
Silver (銀)
Black (黑)
-25 ~ +85
350 ~ 500
470 ~ 22000
10,000 Hrs.
P.169
WL
+85˚C, Screw Terminal Type, Ultra Long Life Assurance
(螺釘型, 超長壽命)
Silver (銀)
Black (黑)
-25 ~ +85
350 ~ 450
2200 ~ 12000
20,000 Hrs.
P.172
WB
+125˚C, Screw Terminal Type, High Temperature
(螺釘型, 高溫度)
Silver (銀)
Black (黑)
-25 ~ +125
160 ~ 400
330 ~ 15000
3,000 Hrs.
P.175
貼片式鋁電解電容器
V-Chip Aluminum Electrolytic Capacitors
貼片品
Surface Mount Type
VS1 +85˚C, Surface Mount Type, General Purpose（貼片普通品）
–40 ~ +85
VT1 +105˚C, Surface Mount Type, General Purpose, 1,000 Hours（貼片普通品）
–55 ~ +105
6.3 ~ 50
0.1 ~ 220
1,000 Hrs.
P.181
VTD +105˚C, Surface Mount Type, General Purpose, 2,000 Hours（貼片普通品）
–55 ~ +105
25 ~ 100
4.7 ~ 1500
2,000 Hrs.
P.183
VTG +105˚C, Surface Mount Type, High Voltage, 3,000 Hours（高壓貼片品）
–25 ~ +105
400
2.2 ~ 4.7
3,000 Hrs.
P.185
VZ2 +105˚C, Surface Mount Type, Low Impedance（低阻抗貼片品）
–55 ~ +105
6.3 ~ 100
1 ~ 1500
2,000 Hrs.
P.187
VTL +105˚C, Surface Mount Type, Long Life, 3,000/5,000 Hours（長壽命貼片品）
–40 ~ +105
10 ~ 50
0.1 ~ 1000
3,000/5,000Hrs.
P.189
6.3 ~ 50
0.1 ~ 1500
2,000 Hrs.
5
P.179
Index
Series
Application Guidelines (應用指引)
1.
Circuit Design
Index
1.1
Please make sure the environment and mounting conditions to which the capacitor will be exposed are within
the conditions specified in this catalog (or alternate SAMXON’S specifications, such as series drawings).
1.2
Operating temperature and applied ripple current must be within SAMXON’S specification.
■
The capacitor must not be used in an ambient temperature which exceeds the operating temperature
specified in this catalog.
■
Do not apply excessive current which exceeds the allowable ripple current.
1.3
Appropriate capacitors which comply with the life requirement of the products should be selected when
designing the circuit.
1.4
Aluminum electrolytic capacitors are polarized. Do not apply reverse voltage or AC voltage. Please use nonpolar capacitors for a circuit that can possibly see reversed polarity. Note: Even non-polar capacitors cannot be
used for AC voltage application.
1.5
Do not use aluminum electrolytic capacitors in a circuit that requires rapid and very frequent charge/discharge.
In this type of circuit, it is necessary to use a special design capacitor with extended life characteristics.
1.6
Do not apply excess voltage.
1.7
■
Please pay attention so that the peak voltage, which is DC voltage overlapped by ripple current, will not
exceed the rated voltage.
■
In the case where more than 2 aluminum electrolytic capacitors are used in series , please make sure
that applied voltage will be lower than rated voltage and the voltage will be applied to each capacitor
equally using a balancing resistor in parallel with the capacitor.
Outer sleeve of the capacitor is not guaranteed as an electrical insulator.
1.8
■
Do not use a standard sleeve on a capacitor in applications that require the electrical insulation. When
the application requires special insulation, please contact our sales office for details.
■
Do not connect the blank terminal (reinforcing terminal) of a multi-terminal (three- or four-terminal)
product of the snap-in type to another circuit it may cause a short circuit.
Capacitors must not be used under the following conditions:
1.9
■
Capacitors must not be exposed to water (including condensation), brine or oil.
■
Ambient conditions that include toxic gases such as hydrogen sulfide, sulfurous acid, nitrous acid,
chlorine, ammonium, etc.
■
Ambient conditions that expose the capacitor to ozone, ultraviolet ray and radiation.
■
Severe vibration and physical shock conditions that exceed SAMXON’S specifications.
When designing a circuit board, please pay attention to following:
6
■
Make the hole spacing on the P.C. board match the lead spacing of the capacitor.
■
There should not be any circuit pattern or circuit wire above the capacitor safety vent.
■
Unless otherwise specified, following clearance should be mad above the safely vent.
Case Diameter
Gap Required
Φ6.3~16
2mm or more
Φ18~35
3mm or more
Φ40 or more
5mm or more
■
In case the vent side is placed toward P.C. board (such as end seal vented parts), make a corresponding
hole on the P.C. board to release the gas when vent is operated. The hole should be made to match the
capacitor vent position.
■
Do not install screw terminal capacitor with end seal side down. When you install a screw terminal
capacitor in a horizontal mount, the positive terminal must be in the upper position.
1.10 The main chemical solution of the electrolyte and the separator paper used in the capacitors are combustible.
The electrolyte is conductive. When it comes in contact with the P.C. board, there is a possibility of pattern
corrosion or short circuit between the circuit pattern which could in result of smoking or catching fire. Do not
locate any circuit pattern beneath the capacitor end seal.
1.11 Do not design a circuit board so that heat generating components such as resistor and transistors are placed
near an aluminum capacitor or reverse side of P.C. board (under the capacitor).
1.12 Electrical characteristics may vary depending on changes in temperature and frequency. Please consider this
variation when you design circuits.
1.13 When you are designing capacitors for use on double-sided P.C. boards, do not place capacitors on circuit
patterns or over the unused holes.
1.14 The torque for terminal screw or brackets screws must be within the specified value on SAMXON’s drawings.
1.15 When you install more than 2 capacitors in parallel, consider the balance of current flowing into the
capacitors.
2.
Mounting
2.1
Once a capacitor has been assembled in the set and power applied, do not attempt to reuse the capacitor in
other circuits or application.
2.2
Electric potential between positive and negative terminal may exist as a result or returned electromotive force,
so please discharge the capacitor using a 1kΩ resistor.
2.3
Leakage current of the parts that have been stored for more than 6 months may increase. When leakage
current has increased, please perform a voltage treatment using 1kΩ resistor.
2.4
Please confirm ratings before installing capacitors on the P.C. board.
2.5
Please confirm polarity before installing capacitors on the P.C. board.
2.6
Do not drop capacitors on the floor, nor use a capacitor that was dropped.
2.7
Be careful not to deform the capacitor during installation.
2.8
Please confirm that the lead spacing of the capacitor matches the hole spacing of the P.C. board prior to
installation.
2.9
Snap-in can type capacitor such as JIS configuration 692, 693, 694 and 695 type should be installed tightly to
the P.C. board (allow no gap between the P.C. board and bottom of the capacitor).
2.10 Please pay attention that the clinch force is not too strong when capacitors are placed and fixed by an
automatic insertion machine.
7
Index
Application Guidelines (應用指引)
Application Guidelines (應用指引)
2.11 Please pay attention to that the mechanical shock to the capacitor by suction nozzle of the automatic insertion
machine or automatic mounter, or by product checker, or by centering mechanism.
2.12 Soldering condition must be confirmed to be within SAMXON’S specification.
Index
■
Pb/Sn Type
Flow Soldering: 235 ±5˚C ≤10 sec.
Hand Soldering (Soldering iron tip): 350 ±10˚C ≤3 sec.
■
Pb-free Type
Flow Soldering: 260 ±5˚C ≤10 sec.
Hand Soldering (Soldering iron tip): 400 ±10˚C ≤3 sec.
2.13 Do not tilt lay down or twist the capacitor body after the capacitor are soldered to the P.C. board.
2.14 Do not carry the P.C. board by grasping the soldered capacitor.
2.15 Please do not allow anything to touch the capacitor after soldering. If P.C. board are stored in stack, please
make sure P.C. board or the other components do not touch the capacitor. The capacitors shall not be effected
by any radiated heat from the soldered P.C. board or other components after soldering.
2.16 Do not clean capacitors with halogenated cleaning agent.
2.17 Precautions on fixing materials and coating materials.
■
Do not use any ingredients which contain halogen.
■
Please pay attention to remove flux and any contamination which remains in the gap between the end
seal and P.C. board and dry that portion well before coating.
■
Please do not apply any material all around the capacitor body but apply it partially.
■
Please contact our sales office to make sure whether the curing condition of coating material would
cause any problems.
2.18 Do not install screw terminal capacitor with end seal side down. When you install a screw terminal capacitor
in a horizontal position, the positive terminal must be in the upper position.
3.
4.
Storage
3.1
The characteristics of aluminum electrolytic capacitors degrade when stored in a static condition for long
period of time. The rate of deterioration depends upon temperature and humidity.
3.2
Capacitors should be stored at the temperature of 5˚C to 35˚C, the humidity of less than 75% RH and out of
direct sunlight.
3.3
Capacitors that have been stored for long periods normally over one year should be subjected to a “voltage
aging” treatment before use. This will reform and repair the oxide dielectric.
3.4
Suggested aging procedure is gradually applying the rated voltage to the capacitor(s) for 30 to 60 minutes. If
the capacitance still exceeds the specified leakage current value, please do not use it.
Disposal
4.1
Dispose of capacitors as industrial waste.
4.2
Consignment to the waste disposal specialists to handle it professionally.
The above mentioned material according to EIAJ RCR-2367B (issued in March, 2002), titled “Guideline of notabilia for aluminum electrolyic
capacitors for use in electronic equipment”. Please refer to the book for details.
8
Application Guidelines (應用指引)
Printed Circuit Board Cleaning
5.1
Foreword
It had been generally accepted that halogen type organic solvents were hazardous to aluminum electrolytic
capacitors. This is because an organic solvent can permeate the capacitor through the end seal. Then, the
solvent dissolves and free chlorine ion (CI¯ion), which can corrode the aluminum electrodes. The following
measures were previously the only way to avoid this phenomenon.
■
Use of cleaning agents, not hazardous to capacitors such as water or alcohol.
■
Mount capacitors on PC boards cleaned with a halogen type solvent beforehand.
■
Use of epoxy end seals
These measures have disadvantages with respect to working efficiency, cleaning capability, cost etc. Therefore,
aluminum electrolytic capacitors which can withstand halogen type cleaning agents are desirable.
5.2
Types of Cleaning Agents
Generally there are three types of cleaning agents.
■
Water type
■
Alcohol type
■
Halogen type
Of these, water and alcohol will have little effect even if they permeate the capacitor. However, halogens can
cause corrosion of aluminum foil and tab. Common types of halogen cleaning agents are listed in Table below:
Chemical Name
Trichlorotrifluoroethane
Fluorotrichloromethane
Trichloroethane
Trichloroethylene
Methyl Chloride
Structural Formula
C2CI3F3
CCI3F
C2H3CI3
C2HCI3
CH3CI
Representative Brand Name
Freon TF, Daiflon S-3
Freon-11, Daiflon S-1
Chloroethene
Trichlene
MC
The last four solvents listed above are particularly corrosive to aluminum and are not recommended to use as
cleaning solvents.
5.3
Penetration Channel of Solvent and Corrosion Mechanism
The three channels by which solvents can penetrate into the capacitor are illustrated:
■
ᰑ
Penetration through a clearance between the rubber and the aluminum
case (curled section)
■
ᰒ
Penetration through a clearance between the rubber and the lead wires
■
ᰓ
Permeation through the rubber end seal
To reduce the possibility of solvents entering a capacitor, tight sealing is required to eliminate clearances
between the rubber and the aluminum case/lead wires. A solvent resistant rubber material is also a necessity.
When a solvent, for example, trichlo-rotrifluoroethane gets inside a non anti-solvent capacitor, the chlorine
ion is free as shown by the following reaction formula.
Thus, the CI¯ion is free again and repeats the corrosion of aluminum. The degree of this reaction depends on
the volume of solvent, the ambient temperature of the capacitor in service, the applied voltage and time etc.
9
Index
5.
Application Guidelines (應用指引)
6.
Basic Electrical Characteristics Capacitance:
Index
The capacitance of capacitor is determined as AC capacitance by measuring its impedance. As the AC capacitance
depends on frequency, voltage and other measuring methods, JIS C 5102 prescribes that the series capacitive
component of an equivalent series circuit
shall be considered as the capacitance by measuring it at
a frequency of 120Hz and a maximum AC voltage of 0.5Vrms with a DC bias voltage of 1.5 to 2.0V applied for
aluminum electrolytic capacitors.
The capacitance of an aluminum electrolytic capacitor shows
smaller values as a measuring frequency increases. See the typical
behavior shown as right chart.
Measuring temperature as well as frequency effects the
capacitance. As the measuring temperature decreases, the
capacitance shows smaller values. See the typical behavior shown
as right chart.
On one hand, DC capacitance, which can be determined by measuring the charge when a DC voltage is applied,
shows a slightly larger value than the AC capacitance at a normal temperature and has the flatter characteristic over
the temperature range.
Tan δ (tangent of loss angle or dissipation factor):
The tan δ is the ratio of the resistive component (ESR) to
the capacitive reactance (1/ωC) in the equivalent series
circuit, and its measuring conditions are the same as the
capacitance.
The tan δ show higher values as a
measuring frequency increases and a
measuring temperature decreases, as
follows:
Equivalent Series Resistance (ESR)
The ESR is comprised of the resistance due to aluminum oxide layer and electrolyte/separator combination and other
resistance effected with foil length, foil surface area, etc.
The ESR value depends on the temperature. Decreasing the temperature makes the resistivity of the electrolyte
increase with the result of the ESR increasing.
As the measuring frequency increases, the ESR decreases and reaches an almost constant value that is mainly the
frequency-independent resistance due to electrolyte/separator combination.
10
Application Guidelines (應用指引)
Impedance (Z):
Index
The impedance is the resistance which oppose the flow of
alternating current at a specific frequency. It is related to
capacitance (C) and inductance (L) in terms of capacitive and
inductive reactance, and also related to the ESR. It is expressed as
follows:
As shown as right chart, the capacitive reactance (Xc)
predominates at the range of low frequencies, and the
impedance decreases with increasing frequency until it reaches
the ESR in the middle frequency range. At the range of the higher
frequencies the inductive reactance (XL) comes to predominate,
so that the impedance increases with increasing the measuring
frequency.
As shown as right chart, the impedance value varies with
temperature, because the resistance of the electrolyte strongly
changes with temperature.
Leakage Current:
The dielectric of a capacitor has a very high resistance
which prevents the flow of DC current. However, due to the
characteristics of the aluminum oxide layer that functions as a
dielectric in contact with electrolyte, a small amount of current,
called leakage current, will flow to reform and repair the oxide
layer while a voltage is being applied. As shown below, a high
leakage current flows in the first minutes as a voltage is applied
to the capacitor, and then the leakage current will decrease and
reach an almost steady-state value with time.
Measuring temperature and voltage effect the leakage current.
The leakage current shows higher values as the temperature and
voltage increase.
In general, the leakage current is measured at 20˚C by applying
the rated voltage, which is applied through a resistor of 1,000Ω
connected in series with the capacitor, and several minutes after
the capacitor reached the rated voltage. The catalog prescribes
the measuring temperature and time.
LIFE ESTIMATION CHART
11
Application Guidelines (應用指引)
7.
Quality Policy
7.1
General
Index
Our basic corporate goals and commitment to total quality are set down in our quality policy. The quality of
our products and services is an essential part of our corporate strategy, whose paramount aim is total customer
satisfaction. Consistent application of quality management system results in flawless products and a high level
of user benefit from our components. Our quality management system always reflects the most stringent
international standards.
Our corporate goals is to play a leading role among the world’s most competitive companies in electronic
components. All quality management measures are geared to optimum customer benefit.
They include:
■
Mastery of processes
■
Continuous improvement programs to narrow process tolerances, and to increase quality and yield.
■
Enhanced productivity
■
Continuous optimization of material, capital and human resources.
■
Promotion of innovation
■
Putting customer benefit first in every product we design. Determining customer needs in partnership
with customers, and rapid implementation of agreements.
The SAMXON quality management system, which is documented in the new edition of the company-wide
SAMXON Quality Management Handbook, is designed to support this strategy.
7.2
Quality assurance
The required measures and regulations for quality assurance are documented in instructions on operations
and procedures; the effectiveness and adequacy of the QA system are regularly checked in internal audits.
7.3
Quality programs
Project-oriented improvement programs pursuing the strategic objective of zero defects are set up and
conducted by specialist teams.
7.4
Process assurance
Assurance of production processes starts as early as the planning and development phase. Quality tools like
FMEA and SVP help detect and avoid potential errors, and safeguard process capability and product quality.
Documentation of all production and testing steps as well as training of personnel are essential to flawless
production. Statistical process control (SPC) is used wherever applicable. Permanent availability of plant is
ensured by preventive maintenance.
7.5
Incoming inspection
Raw materials, parts and consumable undergo incoming inspection appropriate to their significance in the end
product, unless this responsibility has been transferred to the supplier under a quality assurance agreement or
similar.
7.6
In-process inspection
Wherever possible, in-process inspection in conducted to certify the conformity not only of intermediate
products, but also of process supervision and control (e.g. SPC). It is generally integrated into the process steps
and designed to be as preventive as possible, i.e. to avoid errors.
7.7
Final inspection/approval for shipment
Final inspection verifies the major properties of the end products batch by batch, usually by means of fully
automated selection tests.
Approval for shipment helps certify that products shipped comply with specifications. It includes:
■
Testing of principal parameter,
■
Identification check and visual assessment,
■
Examination of papers accompanying the batch.
12
Application Guidelines (應用指引)
Manufacturing and quality assurance procedures for Al electrolytic capacitors
Incoming goods
Inspection of raw materials and parts
Automatic monitoring of etching
and forming process
Etching and forming of aluminum foil
Prefabrication
Index
QC gate
Inspection of etching and forming
electrolytes, electrolyte monitoring
Foil sampling, testing of mechanical
and electrical characteristics
Checking the plotter diagrams of the etching
and forming process
QC gate
Classification and sorting of anode groups
Foil cutting and delivery
Inspection and approval by quality control team
Capacitor production
QC gate
Testing and final inspection
8.
Winding
Checking that the winding data
are adhered to, inspection of terminals
Impregnation and forming
Checking of equipment and settings,
electrolyte monitoring
Riveting, welding, assembly
Sampling of assembly,
riveting and weld quality (SPC)
Seal curling, washing, marking,
insulating and aging
Sampling to test seals and finish
100% final inspection of electrical parameters
Checking automatic test equipment
and relevant settings
QC gate
Visual inspection and packing
Inspection of packing
(markings, contents, date code)
Conformance inspection
Tests of mechanical
and electrical characteristics, packing
QC gate
Stock
Approval by quality control team
Dispatch
Identity check
13
Application Guidelines (應用指引)
9.
Environmental
Environmental policy
Our fundamental commitment to protection of the environment is laid down in SAMXON environmental policy:
Index
10.
■
We work continuously to lighten the burden on the environment and to reduce consumption of energy and
resources beyond statutory requirements.
■
We take all precautions to avoid environmental hazards and to prevent damage to the environment.
■
Potential impact on the environment is assessed and flows into product and process planning at the earliest
possible stage.
■
Our environmental management system ensures that our environmental policy is effectively implemented.
The technical and organizational procedures required are regularly monitored and constantly upgraded.
■
Every employee is required to act in an environmentally conscious manner. It is a permanent task of
management to promote awareness of responsibility for the environment at all levels.
■
We seek to influence our business associates to follow environmental guidelines similar to ours. We supply
our customers with information on environmentally friendly use of our products. We work in a spirit of
cooperation with the authorities.
■
We inform the public of the environmental impact of our activities and the environmental achievements of
our company.
Compliance with RoHS Directive
The company is committed to compliance with the European Union Restriction of Hazardous Substance (RoHS)
Directive. We hereby guarantee that our products do not contain following materials exceeding the RoHS Directive
(2011/65/EU).
11.
■
Lead (Pb) and its compounds
≤1000ppm
■
Mercury (Hg) and its compounds
≤1000ppm
■
Cadmium (Cd) and its compounds
≤100ppm
■
Hexavalent chromium, Cr6+, Cr VI
≤1000ppm
■
Polybrominated biphenyls, PBBs
≤1000ppm
■
Polybrominated diphenyls, PBDEs
≤1000ppm
Halogen Free Compliant
The products identified in the catalogue, and their homogeneous subcomponents, do not contain any of the
following substances in concentrations greater than the listed maximum limits.
Substance
Bromine (Br)
Chlorine (Cl)
Total concentration of Chlorine (Cl) + Bromine (Br)
14
Maximum Limit (ppm)
900 ppm (0.09%)
900 ppm (0.09%)
1500 ppm (0.15%)
Part Number System (產品編碼)
2
3
4
5
6
7
8
9
10 11 12
13 14
15 16
17
SA
P
EGS
105
M
1H
D11
TC
SERIES
CAPACITANCE
TOLERANCE
VOLTAGE
CASE SIZE
TYPE
Code
Tol. (%)
Code
0.1
104
±5
J
±10
K
0.22
224
±15
L
±20
M
Cap (uF)
0.33
0.47
334
474
±30
N
1
105
-40
0
W
2.2
225
-20
0
A
3.3
335
-20
+10
C
-20
+40
X
-20
+50
S
336
-10
0
B
47
476
-10
+20
V
100
107
-10
+30
Q
220
227
-10
+50
T
330
337
+13
+50
E
-5
+15
F
4.7
475
10
106
22
226
33
470
477
2200
228
22000
229
-5
+20
G
33000
339
0
+20
R
47000
479
0
+30
O
100000
10T
0
+50
I
150000
15T
+5
+15
Z
220000
22T
+5
+20
D
330000
33T
10M
+10
+50
H
1000000
1500000
15M
2200000
22M
3300000
33M
Vol. (W.V.)
2
2.5
4
6.3
8
10
12.5
16
20
25
30
32
35
40
42
50
57
63
71
75
80
85
90
100
120
125
150
160
180
200
215
220
230
250
275
300
310
315
330
350
Code
0D
0E
0G
0J
0K
1A
1B
1C
1D
1E
1I
13
1V
1G
1M
1H
1L
1J
1S
1T
1K
1R
19
2A
2O
2B
2Z
2C
2P
2D
22
2N
23
2E
2T
2I
2R
2F
2U
2V
360
375
385
400
420
450
500
550
600
630
2X
2Q
2Y
2G
2M
2W
2H
25
26
2J
Case Size
Diameter(Φ)
Code
3
B
3.5
1
4
C
5
D
6.3
E
8
F
10
G
12.5
I
13
J
13.5
V
14
4
14.5
A
16
K
16.5
7
18
L
18.5
8
20
M
22
N
25
O
30
P
34
W
35
Q
40
R
42
4
45
6
51
S
63.5
T
76
U
80
8
90
X
100
Z
Len. (mm)
Code
4.5
45
5
05
5.4
54
7
07
7.7
77
10.2
T2
11
11
11.5
1A
12
12
12.5
1B
13
13
13.5
1C
20
20
25
25
29.5
2J
30
30
31.5
3A
35
35
35.5
3E
50
50
80
80
100
1L
105
1K
110
1M
120
1N
130
1P
140
1Q
150
1R
155
1E
160
1S
165
1F
170
1T
180
1U
190
1V
200
2L
215
2A
210
2M
220
2N
240
2Q
250
2R
260
2S
270
2T
Feature
Code
Radial bulk
RR
Ammo Taping
2.0mm Pitch
TT
2.5mm Pitch
TU
3.5mm Pitch
TV
5.0mm Pitch
TC
SLEEVE
MATERIAL
SAMXON Product Line
For internal use only
(The product lines we
have H,A,B,C,D,E,M or
0,1,2,3,4,5,9).
Sleeve Material Code
PET
P
PVC
If the sleeve material is PVC, there will be blank in seventeenth digit.
Series
EKF
EKS
EGS
EKM
EKG
EOM
EGF
ESF
EGT
EGK
ESK
ESH
ESK
ERS
EGY
ERF
ERR
ERT
ERE
ERD
ERH
EBD
ERA
ERB
ERC
EFA
ENP
ENH
ERW
ERY
ELP
EAP
EQP
EDP
ETP
EHP
EUP
EKP
EPK
EEP
EFP
ESP
EVP
EGP
EWR
EWI
EWT
EWX
EWF
EWH
EWL
EWB
VS1
VT1
VTD
VTG
VZ2
VTL
SAMXON
PRODUCT LINE
Lead Cut & Form
CB-Type
CB
CE-Type
CE
HE-Type
HE
KD-Type
KD
FD-Type
FD
EH-Type
EH
PCB Terminal
SW
Snap-in
SX
SZ
Lug
SG
O5
O6
T5
Screw
T6
D5
D6
15
Index
1
Taping Specifications (編帶產品規格)
Index
SPECIFICATIONS
Item
Dimensions (mm)
Reference figure
Fig 1
Diameter
D
Height
Lead Diameter
Fig 2
3
4~5
5
6.3
A
5
5~7
9 ~ 15
5~7
d
0.4
0.45
0.5
0.45
Fig 3
8
10
12.5
16, 18
9 ~ 15
11 ~ 20
9 ~ 21
0.5
0.5
0.6
0.6
0.8
15 ~ 35 15 ~ 40
Fig 4
Tol.
4, 5, 6.3
5, 6.3
8
5~7
9 ~ 15
5~9
11 ~ 20
0.45
0.5
0.45
0.5
±0.05
Component Spacing
P
12.7
12.7
12.7
12.7
15
30
12.7
12.7
±1.0
Pitch of sprocket holes
P0
12.7
12.7
12.7
12.7
15
15
12.7
12.7
±0.2
Distance between centres of
component leads
F
2.5
2.5
3.5
5.0
5.0
7.5
5.0
5.0
±0.8
0.5
Carrier tape width
W
18.0
18.0
18.0
18.0
18.0
18.0
18.0
18.0
±0.5
Distance between the center
of upper edge of carrier tape
and sprocket holes
W1
9.0
9.0
9.0
9.0
9.0
9.0
9.0
9.0
±0.5
Distance between the
abscissa and the bottom of
the components body
H
18.5
18.5
18.5
18.5
18.5
18.5
Distance between the
abscissa and the reference
plane of the components
with crimped leads
H0
–
–
–
–
–
–
16.0
16.0
±0.5
Hold down tape width
W0
7.0
7.0
7.0
7.0
12
12
7.0
7.0
Min.
Max. lateral deviation of
the component body vertical
to the tape plane
Δh
0
0
0
0
0
0
0
0
±1.0
Distance between the upper
edges of the carrier tape and
the hold down tape
W2
0~3
0~3
0~3
0~3
0~3
0~3
0~3
0~3
–
Distance between center of
terminal and the sprocket
holes
P1
5.1
5.1
4.6
3.85
5.0
3.75
3.85
3.85
±0.5
Distance between center of
the component and
sprocket holes
P2
6.35
6.35
6.35
6.35
7.5
7.5
6.35
6.35
±1.0
16
17.5
18.5
17.5
20.0
±0.75
0.5
Index
Packing Specifications (包裝規格)
PACKING QUANTITY (TAPING TYPE)
ΦD x L (mm)
3x5
4x5~7
5 x 5 ~ 11
6.3 x 5 ~ 12
8 x 5 ~ 12
8 x 14 ~ 20
10 x 12.5
10 x 16
10 x 20 ~ 25
10 x 30
12.5 x 20
12.5 x 25
12.5 x 35
16 x 25
16 x 30 ~ 35
18 x 20 ~ 25
18 x 30 ~ 35
18 x 40
L (mm)
330
330
330
330
330
330
330
330
323
330
325
325
325
315
315
343
343
343
W (mm)
229
229
229
229
229
229
191
191
191
191
267
270
270
221
221
275
275
275
H (mm)
51
51
51
51
51
64
51
56
64
69
58
63
74
63
76
63
73
73
Inner Box Quantity
3,000
2,500
2,000
1,500
1,000
1,000
500
500
500
500
500
500
500
250
250
250
250
250
Outer Box Quantity
30,000
25,000
20,000
15,000
10,000
8,000
5,000
5,000
4,000
4,000
2,000
2,000
2,000
1,000
1,500
1,000
500
500
PACKING QUANTITY (BULK TYPE)
Long Lead Wire Product
ΦD x L (mm)
3x5
4x5
4x7
5x5
5x7
5 x 11
6.3 x 5 ~ 7
6.3 x 11
8x5~7
8x9
8 x 10 ~ 16
8 x 20
8 x 25
10 x 12.5
10 x 15 ~ 20
10 x 25 ~ 30
12.5 x 20
12.5 x 25
12.5 x 30 ~ 35
12.5 x 40
16 x 20
16 x 25 ~ 30
16 x 35 ~ 40
18 x 15 ~ 20
18 x 25 ~ 30
18 x 35 ~ 50
Plastic Bag Quantity
1,000
1,000
1,000
1,000
1,000
1,000
1,000
1,000
1,000
500
500
200
200
400
200
200
150
150
100
–
–
–
–
–
–
–
Inner Box Quantity
24,000
16,000
14,000
12,000
10,000
8,000
8,000
6,000
6,000
4,000
3,000
1,600
1,200
2,400
1,200
1,200
1,200
900
600
300
200
200
200
150
150
150
Outer Box Quantity
96,000
64,000
56,000
48,000
40,000
32,000
32,000
24,000
24,000
16,000
12,000
6,400
4,800
9,600
7,200
4,800
4,800
3,600
2,400
1,800
2,000
1,600
1,200
1,500
1,200
900
PACKING QUANTITY (SNAP-IN)
Snap-in Terminal Product
ΦD x L (mm)
20 x 25
20 x 30 ~ 40
22 x 25
22 x 30 ~ 40
22 x 45 ~ 50
25 x 25
Inner Box Quantity
100
100
100
100
100
100
Outer Box Quantity
1,200
1,000
1,200
1,000
800
1,000
ΦD x L (mm)
25 x 30 ~ 35
25 x 40 ~ 50
30 x 30 ~ 35
30 x 40 ~ 50
35 x 30 ~ 35
35 x 40 ~ 50
Inner Box Quantity
100
100
50
50
40
40
Outer Box Quantity
800
600
500
400
400
320
17
Lead Forming Specifications (成型產品規格)
Index
SHAPE CODE
ΦD
F
1.5
2.0
2.5
3.5
5.0
5.0
7.5
7.5
CB
H
3.5
3.5
3.5
3.5
3.5
3.5
3.5
3.5
Φd ±0.05
0.45
0.5
0.5
0.5
0.6
0.6
0.8
0.8
F
5.0
5.0
5.0
5.0
–
–
–
–
–
HE
FD
KD
EC
PC
18
4
5
6.3
8 (L >5mm)
10
13
16
18
H1
5.0
5.0
5.0
5.0
–
–
–
Φd ±0.05
0.45
0.5
0.5
0.5
–
–
–
–
F
5.0
5.0
5.0
5.0
–
–
–
–
H1
4.5
4.5
4.5
4.5
–
–
–
–
H2
1.8
1.8
1.8
1.8
–
–
–
–
–
Φd ±0.05
0.45
0.5
0.5
0.5
–
–
–
E
1.12
1.12
1.12
1.30
–
–
–
–
F
–
–
–
–
5.0
5.0
7.5
7.5
H1
–
–
–
–
4.5
4.5
4.5
4.5
H2
–
–
–
–
2.0
2.0
2.0
2.0
Φd ±0.05
–
–
–
–
0.6
0.6
0.8
0.8
E
–
–
–
–
1.30
1.30
1.30
1.30
F
5.0
5.0
5.0
5.0
–
–
–
–
F1
1.2
1.2
1.2
1.2
–
–
–
–
H1
4.0
4.0
4.0
4.0
–
–
–
–
Φd ±0.05
0.45
0.5
0.5
0.5
–
–
–
–
F
–
2.0
2.5
3.5
5.0
5.0
7.5
7.5
H
–
4.0
4.0
4.0
4.0
4.0
4.0
4.0
H1
–
3.0
3.0
3.0
3.0
3.0
3.0
3.0
Φd ±0.05
–
0.5
0.5
0.5
0.6
0.6
0.8
0.8
KF
5mmL (高), +105˚C
Series
FEATURES
Ò
Super miniature, 5mmL, high temperature, suitable for use in electronic circuit of high
density assembly of video recorder, remote controller, VCD etc.
Performance Characteristics
Operating Temperature Range
-40 to +105˚C
Rated Working Voltage Range
4 to 50V
Nominal Capacitance Range
3.3 to 330μF
Capacitance Tolerance
±20% at 120Hz, +20˚C
Leakage Current
I ≤0.01CV or 3 (μA)
whichever is greater measured after 2 minutes application of rated working voltage at +20˚C
Working Voltage (V)
tan δ (max.)
tan δ (120Hz, +20˚C)
Low Temperature Characteristics
4
0.37
6.3
0.28
10
0.24
16
0.20
25
0.16
35
0.13
50
0.12
4
6
12
6.3
3
8
10
3
5
16
2
4
25
2
3
35
2
3
50
2
3
Impedance ratio max. at 120Hz
Working Voltage (V)
Z-25˚C / Z+20˚C
Z-40˚C / Z+20˚C
Test time
: 1,000 hours
Test temperature : +105˚C
Test conditions
: Rated DC working voltage
High Temperature Loading
Post test requirements at +20˚C
Leakage current
: ≤Initial specified value
Cap. change
: within ±20% of the initial measured
with rated ripple current
value (4V: within ±30%)
: ≤200% of the initial specified value
tan δ
Shelf Life
At +105˚C no voltage applied after 1,000 hours and then being stabilized at +20˚C the capacitors shall meet the
following limits
Leakage current : ≤Initial specified value
Cap. change
: within ±20% of the initial measured value (4V: within ±30%)
tan δ
: ≤200% of the initial specified value
Industrial Standard
JIS C - 5101-4 (IEC 60384-4)
CASE SIZE TABLE
ΦD
4
5
6.3
8
F
1.5
2.0
2.5
2.5
Φd
0.45
RIPPLE CURRENT MULTIPLIER
Frequency Coefficient
Coefficient
Freq. (Hz)
50
120
300
1k
10k~
≤47
0.75
1.00
1.35
1.57
2.00
68~330
0.80
1.00
1.23
1.34
1.50
Cap (μF)
PART NUMBER SYSTEM (EXAMPLE : 16V 33μF)
1
23
456
7
89
10
11 12
13 14
E
KF
336
M
1C
E
05
RR
Type (Radial Bulk)
Case Length (5mm)
Diameter (6.3mm)
Voltage (16V)
Tolerance (±20%)
Capacitance (33μF)
Series
E-CAP
19
Miniature Aluminum Electrolytic Capacitors
Item
KF
SPECIFICATIONS
KF
5mmL (高), +105˚C
Series
STANDARD RATINGS
Voltage (Code)
Cap. (μF)
Code
10
106
22
4V (0G)
6.3V (0J)
10V (1A)
16V (1C)
Case Size
Ripple Current
Case Size
Ripple Current
Case Size
Ripple Current
Case Size
Ripple Current
226
4x5
22
4x5
22
4x5
24
4x5
18
5x5
33
336
5x5
30
5x5
30
5x5
30
35
6.3 x 5
40
50
47
476
5x5
36
5x5
36
6.3 x 5
46
6.3 x 5
100
107
6.3 x 5
60
6.3 x 5
60
6.3 x 5
67
6.3 x 5
73
220
227
8x5
103
8x5
116
8x5
126
330
337
8x5
127
Case Size ΦD x L (mm)
Maximum Allowable Ripple Current (mArms) at 105˚C 120Hz
Voltage (Code)
Cap. (μF)
Code
3.3
335
4.7
475
25V (1E)
35V (1V)
50V (1H)
Case Size
Ripple Current
Case Size
Ripple Current
Case Size
Ripple Current
4x5
11
4x5
14
4x5
13
4x5
15
5x5
19
KF
10
106
4x5
20
5x5
25
6.3 x 5
30
22
226
6.3 x 5
38
6.3 x 5
48
8x5
52
8x5
63
33
336
6.3 x 5
48
6.3 x 5
59
47
476
6.3 x 5
58
8x5
82
100
107
8x5
97
Maximum Allowable Ripple Current (mArms) at 105˚C 120Hz
Case Size ΦD x L (mm)
Miniature Aluminum Electrolytic Capacitors
Specifications are subject to change without notice. Should a safety or technical concern arise regarding the product, please be sure to contact our sales
offices or agents immediately.
20
KS
7mmL (高), -40˚C~+105˚C
Series
FEATURES
Ò
Ò
Rated working voltage range 6.3 to 50V DC operation temperature range -40 to +105˚C.
This series is for communication equipments, switching power supply, industrial measuring instruments,
automotive electric products, etc.
SPECIFICATIONS
Item
Performance Characteristics
Operating Temperature Range
-40 to +105˚C
Rated Working Voltage Range
6.3 to 50V
Nominal Capacitance Range
3.3 to 330μF
Capacitance Tolerance
±20% at 120Hz, +20˚C
I ≤0.01CV or 3 (μA)
Leakage Current
Low Temperature Characteristics
Impedance ratio max. at 120Hz
Working Voltage (V)
Z-25˚C / Z+20˚C
Z-40˚C / Z+20˚C
6.3
0.24
10
0.21
16
0.18
25
0.15
35
0.13
50
0.12
6.3
10
16
25
35
50
4
8
2
5
2
4
2
3
2
3
2
3
Test time
: 1,000 hours
Test temperature : +105˚C
Test conditions
: Rated DC working voltage
High Temperature Loading
Post test requirements at +20˚C
Leakage current
: ≤Initial specified value
Cap. change
: within ±20% of the initial measured
with rated ripple current
value
tan δ
: ≤200% of the initial specified value
Shelf Life
At +105˚C no voltage applied after 1,000 hours and then being stabilized at +20˚C the capacitors shall meet the
following limits
Leakage current : ≤Initial specified value
Cap. change
: within ±20% of the initial measured value
tan δ
: ≤200% of the initial specified value
Industrial Standard
JIS C - 5101-4 (IEC 60384-4)
CASE SIZE TABLE
ΦD
4
5
6.3
8
F
1.5
2.0
2.5
3.5
Φd
0.45
α
(L ≤7) 1
(L ≥9) 1.5
RIPPLE CURRENT MULTIPLIER
Frequency Coefficient
Coefficient
Freq. (Hz)
50
120
300
1k
10k~
≤47
0.75
1.00
1.35
1.57
2.00
68~220
0.80
1.00
1.23
1.34
1.50
Cap (μF)
PART NUMBER SYSTEM (EXAMPLE : 6.3V 47μF)
1
23
456
7
89
10
11 12
13 14
E
KS
476
M
0J
D
07
RR
Type (Radial Bulk)
Case Length (7mm)
Diameter (5mm)
Voltage (6.3V)
Tolerance (±20%)
Capacitance (47μF)
Series
E-CAP
21
Miniature Aluminum Electrolytic Capacitors
Working Voltage (V)
tan δ (max.)
tan δ (120Hz, +20˚C)
KS
whichever is greater measured after 2 minutes application of rated working voltage at +20˚C
KS
7mmL (高), -40˚C~+105˚C
Series
STANDARD RATINGS
Voltage (Code)
6.3V (0J)
Case Size
10V (1A)
Cap. (μF)
Code
10
106
Ripple Current
22
226
4x7
34
4x7
33
336
4x7
37
47
476
4x7
44
100
107
5x7
67
220
227
6.3 x 7
112
330
337
8x7
158
Case Size
16V (1C)
Ripple Current
25V (1E)
Case Size
Ripple Current
Case Size
Ripple Current
4x7
29
4x7
29
34
4x7
38
5x7
45
4x7
40
5x7
50
5x7
55
5x7
50
5x7
60
6.3 x 7
67
5x7
72
6.3 x 7
92
6.3 x 7
97
6.3 x 7
83
8x7
106
8x7
113
8x7
140
8x9
174
Case Size ΦD x L (mm)
Maximum Allowable Ripple Current (mArms) at 105˚C 120Hz
Voltage (Code)
35V (1V)
Case Size
50V (1H)
KS
Cap. (μF)
Code
3.3
335
4.7
475
4x7
24
10
106
5x7
36
22
226
6.3 x 7
57
33
336
6.3 x 7
62
47
476
6.3 x 7
74
100
107
8x9
65
Miniature Aluminum Electrolytic Capacitors
Maximum Allowable Ripple Current (mArms) at 105˚C 120Hz
Ripple Current
Case Size
Ripple Current
4x7
24
5x7
29
5x7
38
6.3 x 7
44
8x7
65
Case Size ΦD x L (mm)
Specifications are subject to change without notice. Should a safety or technical concern arise regarding the product, please be sure to contact our sales
offices or agents immediately.
22
GS
+85˚C, General (普通品)
Series
FEATURES
Ò
Ò
High CV value, guarantee 2,000 hours load life at 85˚C.
Suitable for use in electronic circuits in colour TV receiver, video recorder etc.
SPECIFICATIONS
Item
Performance Characteristics
Operating Temperature Range
-40 to +85˚C
-25 to +85˚C
Rated Working Voltage Range
6.3 to 100V
160 to 450V
Nominal Capacitance Range
2.2 to 22000μF
Capacitance Tolerance
±20% at 120Hz, +20˚C
Leakage Current
tan δ (120Hz, +20˚C)
I ≤0.01CV or 3 (μA) whichever is greater measured after 2
I ≤0.03CV +40 (μA) after 2 minutes application of rated
minutes application of rated working voltage at +20˚C
working voltage at +20˚C
Working Voltage (V)
tan δ (max.)
6.3
0.28
10
0.24
16
0.20
25
0.16
35
0.14
50
0.12
Working Voltage (V)
tan δ (max.)
160
0.20
200
0.20
250
0.20
350
0.25
400
0.25
450
0.25
63
0.10
100
0.08
63
2
3
100
2
3
Impedance ratio max. at 120Hz
Working Voltage (V)
6.3
Z-25˚C / Z+20˚C
5
Z-40˚C / Z+20˚C
12
Low Temperature Characteristics
Working Voltage (V)
Z-25˚C / Z+20˚C
160
3
10
4
10
16
3
8
25
2
5
35
2
4
50
2
3
200
3
250
4
350
4
400
6
450
15
GS
For capacitance value >1000μF, add 0.02 per another 1000μF
Test time
: 2,000 hours
Test temperature : +85˚C
Test conditions
: Rated DC working voltage
High Temperature Loading
Post test requirements at +20˚C
Leakage current
: ≤Initial specified value
Cap. change
: within ±20% of the initial measured
with rated ripple current
value
tan δ
: ≤200% of the initial specified value
Shelf Life
At +85˚C no voltage applied after 1,000 hours and then being stabilized at +20˚C the capacitors shall meet the
following limits
Leakage current : ≤Initial specified value
Cap. change
: within ±20% of the initial measured value
tan δ
: ≤200% of the initial specified value
Industrial Standard
JIS C - 5101-4 (IEC 60384-4)
CASE SIZE TABLE
ΦD
8 (L 1000μF, add 0.5 per another 1000μF for Z-25˚C / Z+20˚C
add 1.0 per another 1000μF for Z-40˚C / Z+20˚C
Miniature Aluminum Electrolytic Capacitors
Test time
: 2,000 hours
Test temperature : +105˚C
Test conditions
: Rated DC working voltage
High Temperature Loading
Post test requirements at +20˚C
Leakage current
: ≤Initial specified value
Cap. change
: within ±20% of the initial measured
with rated ripple current.
value
tan δ
: ≤200% of the initial specified value
Shelf Life
At +105˚C no voltage applied after 1,000 hours and then being stabilized at +20˚C the capacitors shall meet the
following limits
Leakage current : ≤Initial specified value
Cap. change
: within ±20% of the initial measured value
tan δ
: ≤200% of the initial specified value
Industrial Standard
JIS C - 5101-4 (IEC 60384-4)
CASE SIZE TABLE
ΦD
5
6.3
F
2.0
2.5
Φd
0.5
0.5
1
23
456
7
89
10
11 12
13 14
KM
337
M
1E
F
12
RR
12.5
16
18
22
25
3.5
5.0
5.0
7.5
7.5
10.0
12.5
0.5
0.6
0.6
0.6
0.8
0.8
0.8
1.0
(L
工商网监
湘ICP备2023018690号
