PCM-400-12-CF

Additional Resources: Product Page | 3D Model date 06/02/2022 page 1 of 8 SERIES: PCM-400 │ DESCRIPTION: AC-DC POWER SUPPLY FEATURES • • • • • • up to 400 W continuous power universal input (90~264 Vac) active power factor correction peak power of 700W for 500µs duration (single output models only) built-in remote ON/OFF, power good, & fan fail alarm options over voltage, short circuit, over current, and over temperature protection • efficiency up to 87% MODEL preset output voltage customizable output range7 output current output power ripple and noise8,9 efficiency (Vdc) (Vdc) max (forced air) (A) PCM-400-121,2 12 10~13.8 33.33 18.33 400 120 85 1,2 PCM-400-15 15 14~15.5 26.67 14.67 400 150 85 PCM-400-181,2 18 16~20 22.22 12.22 400 180 85 PCM-400-24 24 21~26 16.67 9.17 400 240 87 1,2 PCM-400-28 28 27~34 14.29 7.86 400 280 85 PCM-400-361,2 36 35~42 11.11 6.11 400 360 87 1,2 PCM-400-48 48 43~50 8.33 4.58 400 480 87 PCM-400-541,2 54 51~60 7.41 4.07 400 540 87 1,2 max (convection) (A) max (W) max (mVp-p) typ (%) PCM-400-D05123,4,* Vo1 Vo2 5 12 N/A 30 20.83 15 13.33 320 50 120 87 PCM-400-D05243,4,* Vo1 Vo2 5 24 N/A 30 10.42 15 6.67 320 50 240 87 PCM-400-D05483,4,* Vo1 Vo2 5 48 N/A 30 5.21 15 3.33 320 50 480 87 PCM-400-D12245,6 Vo1 Vo2 12 24 N/A 20.83 10.42 12.5 8.33 400 120 240 87 Notes: 1. For U-frame models, the maximum output power is 400W with a minimum of 27 CFM forced air, 220 W maximum with convection cooling. 2. For CNF models, the maximum output is 220 W with convection cooling. 3. For U-frame models, the total combined output power is 320W with a minimum of 27 CFM forced air, 180 W maximum with convection cooling. 4. For CNF models, the maximum output is 180 W with convection cooling. 5. For U-frame models, the total combined output power is 400W with a minimum of 27 CFM forced air, 200 W maximum with convection cooling. 6. For CNF models, the maximum output is 200 W with convection cooling. 7. Output can be custom set within range. 8. Measured at 10 kHz ~ 20 MHz bandwidth, with a 22 µF electrolytic and 0.1 µF ceramic capacitor on the output. 9. 1% minimum load is required to maintain ripple and regulation (10% for dual output models). 10. * Discontinued model. PART NUMBER KEY PCM-400 - X XX - XXX - X Base Number Output “blank” = Single D = Dual Output Voltage cui.com Chassis Input/Output Connectors U = U-frame “blank” = terminal block CNF = enclosed 1 = header CF = enclosed with top fan CFS = enclosed with rear fan Additional Resources: Product Page | 3D Model CUI Inc │ SERIES: PCM-400 │ DESCRIPTION: AC-DC POWER SUPPLY date 06/02/2022 page 2 of 8 INPUT parameter conditions/description min voltage typ 90 frequency 47 current at 90 Vac, full load inrush current at 115 Vac, cold start at 230 Vac, cold start leakage current at 120 Vac at 240 Vac power factor correction at 230 Vac, full load remote ON/OFF designated as INH on Pin 4 of CN1, requires a low signal to inhibit output input fuse T8 A/250 V on the input max units 264 Vac 63 Hz 8 A 35 70 A A 300 500 μA μA max units 0.9 OUTPUT parameter conditions/description total regulation single output models dual output models transient response returns to within 1% in