VMS-300-D0512-CFS

Additional Resources: Product Page date 06/07/2022 page 1 of 8 SERIES: VMS-300 │ DESCRIPTION: AC-DC POWER SUPPLY FEATURES • • • • • • • up to 3002 W continuous power 12.5 W/in3 power density universal input (90~264 Vac) 12 Vdc auxiliary fan output over voltage, short circuit, and over temperature protections built-in active PFC function efficiency up to 85% RoHS MODEL output voltage output current output power ripple and noise4, 5 efficiency (Vdc) max (A) max (W) max (mVp-p) min (%) VMS-300-12 12 252 3002 120 82 VMS-300-15 15 202 3002 150 82 VMS-300-24 24 12.52 3002 240 83 VMS-300-36 36 8.332 3002 360 84 VMS-300-48 48 6.252 3002 480 84 VMS-300-D0512* V1 V2 5 12 24 13.333 2403 50 120 80 VMS-300-D1224 V1 V2 12 24 13.333 6.673 2403 120 240 85 VMS-300-12-CF 12 25 300 120 82 3 VMS-300-15-CF 15 20 300 150 82 VMS-300-24-CF 24 12.5 300 240 83 VMS-300-36-CF 36 8.33 300 360 84 VMS-300-48-CF 48 6.25 300 480 84 VMS-300-D0512-CF* V1 V2 5 12 24 13.33 2403 50 120 80 VMS-300-D1224-CF V1 V2 12 24 13.33 6.67 2403 120 240 85 VMS-300-12-CFS 12 25 300 120 82 VMS-300-15-CFS 15 20 300 150 82 VMS-300-24-CFS 24 12.5 300 240 83 VMS-300-36-CFS 36 8.33 300 360 84 VMS-300-48-CFS 48 6.25 300 480 84 VMS-300-D0512-CFS* V1 V2 5 12 24 13.33 2403 50 120 80 VMS-300-D1224-CFS V1 V2 12 24 13.33 6.67 2403 120 240 85 Notes: 1. 2. 3. 4. 5. 6. Peak power of 600 W within 500 µs only applies to single output models Total continuous output power will not exceed 300 W with 25 CFM forced air, 150 W without fan. Total combined continuous output power will not exceed 240 W with 25 CFM forced air, 120 W without fan. Measured at 10 kHz ~ 20 MHz, with 0.1 µF ceramic and 22 µF electrolytic parallel capacitors 1% minimum load is required to maintain the ripple and regulation (10% for dual output models) * Discontinued model. cui.com Additional Resources: Product Page CUI Inc │ SERIES: VMS-300 │ DESCRIPTION: AC-DC POWER SUPPLY date 06/07/2022│ page 2 of 8 PART NUMBER KEY VMS-300 - X XXXX - XXX - X Base Number Output “blank” = single D = dual Output Voltage Chasis “blank” = U-frame CF = enclosed with top fan CFS = enclosed with rear fan Input/Output Connectors “blank” = terminal block/terminal block 11,3 = header/header 22 = IEC320/terminal block 32,3 = IEC320/header Notes: 1. U-Frame & CF models 2. CFS models 3. Header output connector not available on single 12 Vdc output models or dual output models INPUT parameter conditions/description min voltage frequency current at 90 Vac, cold start inrush current at 115 Vac, cold start at 230 Vac, cold start power factor correction single output models pass EN61000-3-2 Class D dual output models leakage current at 264 Vac input fuse 5 A / 250 V inserted in primary remote ON/OFF designated as INH on pin 4 of CN3, requires a low signal to inhibit output max units 90 typ 264 Vac 47 63 Hz 5 A 35 70 A A 0.3 mA max units -0.95 OUTPUT parameter conditions/description min load regulation single output models dual output models transient response returns to within 1% in