FH43B-41S-0.2SHW(99)

0.2mm/0.25mm Pitch, 0.9mm Height FPC Connectors FH43BW/FH43MW Series m 7m 2.7 11.8 mm（ 0.9mm The staggered lead structure simplifies PCB mounting and provides a low profile height of 0.9 mm and a 2.77 mm mounting width depth. 51 p os.） Nov.1.2022 Copyright 2022 HIROSE ELECTRIC CO., LTD. All Rights Reserved. Fig.1 ■Features FH43B differential impedance 1. 0.2mm pitch low profile bottom contact FPC connector (0.25mm pitch type also available for some of No. of positions) Spec MAX : 115ohm Maximizes space with contact pitch of 0.2mm, a mated height of 0.9mm, and mounted depth of 2.77mm. *45% reduction in occupied PCB area *55% reduction in weight (Compared to our 0.3mm pitch FH26 Series 51 position connector) 97.2 100.6 Connector 2. Easy PCB mounting FPC Spec MIN : 85ohm The PCB leads use 0.4mm pitch and are staggered which simplifies the PCB mounting process. 3. Supports high-speed transmissions By utilizing differential pairs of identical contacts (even - even contact or odd - odd contacts) these connectors are able to provide superb transmission characteristics and supports eDP (ver. 1.3), MIPI (D-PHY), HDMI (ver 1.3), and USB (3.0) standards. impedance@200ps rise time(10-90%) FPC insertion Actuator open 4. Molded structure aids PCB layout The bottom of this connector is enclosed by a fully molded structure that protects the contacts and removes any restrictions from PCB patterning and layout design. 5. Rotating one-touch ZIF mechanism The one-touch rotating ZIF mechanism is easier to operate and works with a light force, and a clear tactile click is delivered upon the successful completion of the mating process. 6. Easy FPC insertion The FPC aligning mechanism holds onto the FPC prior to locking the actuator. FPC With actuator locked 7. Insertion check window There is a cutout on the actuator that allows you to visually inspect the FPC to make sure that it is locked into place, preventing incorrect insertion of the FPC. 8. Accepts standard 0.2mm thick FPC This connector accepts standard 0.2mm thick FPC. (A stiffener with adequate strength will prevent FPC deformation and ease insertion and mating.) 9. Halogen-free The connector does not use chlorine and bromine exceeding standard limits. *Defined in accordance with IEC61249-2-21 Br 900ppm or lower, Cl 900ppm or lower, Br + Cl 1,500ppm or lower FPC temporary retention system 10.Available for 500 pieces packaging Although the normal product is 5,000 pieces per reel, 500 winds per reel is also available. (Emboss reel external diameter is Ø180mm.) FPC temporary retention system In cases where the application will demand a high level of reliability, such as automotive, please contact a company representative for further information. visual check area to confirm mating 2021.9③ 1 FH43BW/FH43MW Series●0.2mm/0.25mm Pitch, 0.9mm Height FPC Connectors ■Product Specifications Current DC 0.2A Rating (Note 1) Rating Voltage Operating AC 30 Vrms Rating Humidity Range Recommended FPC spec Items Storage Temperature Range Relative humidity 90% max Storing Humidity (should be no condensation) Range Specifications 100V DC 2. Withstanding Voltage No flashover or breakdown 100mø Max. *Excluding FPC conductor resistance 90V AC for 1 Min Contact Resistance : 100mø Max No damage, cracks and looseness of parts 5. Vibration 6. Shock 7. Humidity (Steady State) 8. Temperature Cycle 9. Resistance to soldering heat Relative humidity 90% max (should be no condensation) Conditions 50Mø Min 4. Durability -10 to +50℃ (Note 3) t ＝ 0.2 ±0.02 Gold plating 1. Insulation Resistance 3. Contact Resistance Nov.1.2022 Copyright 2022 HIROSE ELECTRIC CO., LTD. All Rights Reserved. Operating -55 to +85℃ (Note 2) Temperature Range No electrical discontinuity of 1µ or longer Contact Resistance : 100mø Max No damage, cracks and looseness of parts No electric discontinuity of 1µ or longer Contact Resistance : 100mø Max No damage, cracks and looseness of parts Contact Resistance : 100mø Max Insulation Resistance : 50Mø Min No damage, cracks and looseness of parts Contact Resistance : 100mø Max Insulation Resistance : 50Mø Min No damage, cracks and looseness of parts No deformation of case of excessive looseness of the terminal 1mA 10 cycles Frequency 10 to 55Hz, Half amplitude 0.75mm for 10 cycles in 3 axial directions 2 Acceleration : 981m/s , Retention time: 6 ms, Semisinusoidal 3 times in 3 both axial directions 96 hours at 40ç and humidity of 90 to 95% Temperature : -55 → +15 to +35 → +85 → +15 to +35ç Time : 30 → 2 to 3 → 30 → 2 to 3 minutes 5 cycles 1) Reflow : Peak TMP 250ç MAX, reflow TMP over 230ç within 60 seconds 2) Manual soldering : 350 ±10ç for 5 seconds Note 1 : When electrifying rated current to all contacts, use 70% of rated current. Note 2 : Includes temperature rise caused by current flow. Note 3 : The term “storage” refers to the long-term storage condition of unused products before PCB mounting. For no-electrification state after PCB mounting, the operating temperature and humidity are applied. Materials / Finish Product Materials Color/Finish Remarks LCP Beige UL94V-0 PA Black UL94HB Gold plating ― Pure tin reflow plating ― Insulator Contacts Phosphor bronze Metal fittings ■Product Number Structure Refer to the chart below when determining the product specifications from the product number. Please select from the product numbers listed in this catalog when placing orders. FH 43 BW − 51S − 0.2 SHW (10) ❶ ❷ ❸ ❹ ❶ Series Name : FH ❷ Series No. : 43 ❸ BW : 0.2mm pitch, Halogen-free MW : 0.25mm pitch, Halogen-free ❹ No. of Contacts : BW...21-71 MW...17, 19, 41, 55 ❺ Contact Pitch : 0.2mm, 0.25mm 2 ❺ ❻ ❼ ❻ Terminal Type SHW ... SMT horizontal staggered row mounting type ❼ Specifications (10) : Nickel barrier gold plating, 5,000 pieces per reel (99) : Nickel barrier gold plating 500 pieces per reel FH43BW/FH43MW Series●0.2mm/0.25mm Pitch, 0.9mm Height FPC Connectors ■Connector Dimensions (0.08) P Enlarged figure Lot No. HRS mark Polarization mark b±0.1 Cavity No. No. of contacts (0.08) Ｃ±0.1 Nov.1.2022 Copyright 2022 HIROSE ELECTRIC CO., LTD. All Rights Reserved. Ｐ (Ｄ) Ｅ±0.1 (0.12) Contact point (0.31) Contact No.1 FPC：t0.2 (0.95) (2.85) (2.08) 0.9±0.1 (1.75) (2) b±0.1 Contact No.2 Ａ±0.15 Ｂ±0.1 (9 (1 0°) 25 °) a±0.1 (0.53) (1.2) (1.6) 2.17±0.15 0.47±0.1 0.4±0.15 0.3±0.1 0.2±0.15 (0.45) (2.5) Note 1 : The dimensions in parentheses are for reference. Note 2 : Lead coplanarity including reinforced metal fittings shall be 0.1mm MAX. Note 3 : To be delivered with tape and reel packages. See attached packaging specifications for details. Note 4 : Note that preventive hole for sink mark or slit could be added for improvement. Note 5 : The quality remains good, even with the dark spots, which could occasionally occur on molded plastic. Note 6 : The color of the plating may change after the reflow process, but it will not negatively affect the performance of these connectors. Unit : mm HRS No. No. of Contacts A B C D E a b FH43BW-21S-0.2SHW(**) Product No. 580-2822-0 ** 21 5.8 3.6 4 4.53 5.29 0.2 0.4 FH43BW-25S-0.2SHW(**) 580-2830-0 ** 25 6.6 4.4 4.8 5.33 6.09 0.2 0.4 FH43BW-31S-0.2SHW(**) 580-2820-4 ** 31 7.8 5.6 6 6.53 7.29 0.2 0.4 FH43BW-35S-0.2SHW(**) 580-2821-7 ** 35 8.6 6.4 6.8 7.33 8.09 0.2 0.4 FH43BW-41S-0.2SHW(**) 580-2813-9 ** 41 9.8 7.6 8 8.53 9.29 0.2 0.4 FH43BW-45S-0.2SHW(**) 580-2815-4 ** 45 10.6 8.4 8.8 9.33 10.09 0.2 0.4 FH43BW-51S-0.2SHW(**) 580-2814-1 ** 51 11.8 9.6 10 10.53 11.29 0.2 0.4 FH43BW-61S-0.2SHW(**) 580-2816-7 ** 61 13.8 11.6 12 12.53 13.29 0.2 0.4 FH43BW-71S-0.2SHW(**) 580-2819-5 ** 71 15.8 13.6 14 14.53 15.29 0.2 0.4 Product No. HRS No. No. of Contacts A B C D E a b FH43MW-17S-0.25SHW(**) 580-2817-0 ** 17 5.8 3.5 4 4.53 5.29 0.25 0.5 FH43MW-19S-0.25SHW(**) 580-2823-2 ** 19 6.3 4 4.5 5.03 5.79 0.25 0.5 FH43MW-41S-0.25SHW(**) 580-2824-5 ** 41 11.8 9.5 10 10.53 11.29 0.25 0.5 FH43MW-55S-0.25SHW(**) 580-2818-2 ** 55 15.3 13 13.5 14.03 14.79 0.25 0.5 Note 1 : This product is packaged on tape and reel and is only sold in full reel quantities of either 5,000 or 500 piece reels. Please place orders by full reel quantities. 3 FH43BW/FH43MW Series●0.2mm/0.25mm Pitch, 0.9mm Height FPC Connectors BRecommended PCB Mounting Pattern Ｂ (0.2) b 0.04 Contact No.2 Connector Image (Mounting Section) 1.6±0.05 0.9±0.03 Contact No.1 0.4±0.05 b (n+1)/2× d±0.02 0.04 0.485±0.05 Ｃ±0.04 Ｘ Nov.1.2022 Copyright 2022 HIROSE ELECTRIC CO., LTD. All Rights Reserved. (n-1)/2× d±0.02 1.65±0.05 0.87±0.03 3.17±0.05 0.65±0.03 a 0.55±0.03 BRecommended Stencil Pattern (Recommended stencil thickness : t= 0.1) a Ｂ b (n-1)/2× e±0.01 0.04 Y 1.92±0.05 0.3±0.03 b (n+1)/2× e±0.01 0.04 Y 0.585±0.05 Ｃ±0.04 Ｙ 0.68±0.03 1.94±0.05 0.68±0.03 3.17±0.05 (PCB mounting pattern image) Note 7 : 'n' is the number of contacts. 4 C d Unit : mm e 0.4 0.2 0.18 0.4 0.2 0.18 0.4 0.2 0.18 0.4 0.2 0.18 0.4 0.2 0.18 0.4 0.2 0.18 0.4 0.2 0.18 0.4 0.2 0.18 0.2 0.4 0.2 0.18 a b d e Product No. HRS No. No. of Contacts B a b FH43BW-21S-0.2SHW(**) 580-2822-0 ** 21 3.6 4 0.2 FH43BW-25S-0.2SHW(**) 580-2830-0 ** 25 4.4 4.8 0.2 FH43BW-31S-0.2SHW(**) 580-2820-4 ** 31 5.6 6 0.2 FH43BW-35S-0.2SHW(**) 580-2821-7 ** 35 6.4 6.8 0.2 FH43BW-41S-0.2SHW(**) 580-2813-9 ** 41 7.6 8 0.2 FH43BW-45S-0.2SHW(**) 580-2815-4 ** 45 8.4 8.8 0.2 FH43BW-51S-0.2SHW(**) 580-2814-1 ** 51 9.6 10 0.2 FH43BW-61S-0.2SHW(**) 580-2816-7 ** 61 11.6 12 0.2 FH43BW-71S-0.2SHW(**) 580-2819-5 ** 71 13.6 14 Product No. HRS No. No. of Contacts B C FH43MW-17S-0.25SHW(**) 580-2817-0 ** 17 3.5 4 0.25 0.5 0.25 0.23 FH43MW-19S-0.25SHW(**) 580-2823-2 ** 19 4 4.5 0.25 0.5 0.25 0.23 FH43MW-41S-0.25SHW(**) 580-2824-5 ** 41 9.5 10 0.25 0.5 0.25 0.23 FH43MW-55S-0.25SHW(**) 580-2818-2 ** 55 13 13.5 0.25 0.5 0.25 0.23 FH43BW/FH43MW Series●0.2mm/0.25mm Pitch, 0.9mm Height FPC Connectors BRecommended FPC Pattern 0.2±0.02 Ａ±0.1 (Ｆ) Ｇ±0.05 0.25±0.05 0.25±0.05 Ｃ±0.02 Ｒ 0.4 0.4 (n+1)/2× 0.04 Z R0.2MAX Contact No.1 R0.2MAX R0.2±0.1 R0.2±0.1 3.1±0.3(Stiffener) 2.1±0.3 1.6±0.05 1.1±0.05 Ｚ 0.2＋0.03 −0.02 8 0.1±0.03 8 0.1±0.03 8 0.055±0.02 0.2 0.75±0.1(Odd pattern) 0.76±0.1(Even pattern) 1.55±0.15 0.74±0.1(Even pattern) 0.75±0.1(Odd pattern) 1.45±0.1 [FH43BW] R0.2MAX 9 0.67±0.05 0.055±0.02 0.2＋0.03 −0.02 10 Ｑ 0.1±0.15 (n-1)/2× Ｂ 9 Ｈ±0.05 9 0.04 Z 0.67±0.05 R Enlarged figure Ｕ Ｖ (0.05) : Shows recommended demension when lead for plating is required. : Indicated tolerance is applicable to the exposed conductor. : Dimension Q must be 0.5mm minimum. (0.35) Note 8 9 10 (Reference shape) Check mark for press misalignment (0) *Relative positions of point-U and V (0.01) *Relative positions of point-S and T (0.10:Even pattern) (0.13:Odd pattern) (0.5) Nov.1.2022 Copyright 2022 HIROSE ELECTRIC CO., LTD. All Rights Reserved. Contact No.2 Ｔ Ｓ 0.01±0.02 Unit : mm H Product No. HRS No. No. of Contacts A B C F G FH43BW-21S-0.2SHW(**) 580-2822-0 ** 21 5.8 3.6 4 5.3 4.5 FH43BW-25S-0.2SHW(**) 580-2830-0 ** 25 6.6 4.4 4.8 6.1 5.3 5.74 FH43BW-31S-0.2SHW(**) 580-2820-4 ** 31 7.8 5.6 6 7.3 6.5 6.94 FH43BW-35S-0.2SHW(**) 580-2821-7 ** 35 8.6 6.4 6.8 8.1 7.3 7.74 FH43BW-41S-0.2SHW(**) 580-2813-9 ** 41 9.8 7.6 8 9.3 8.5 8.94 FH43BW-45S-0.2SHW(**) 580-2815-4 ** 45 10.6 8.4 8.8 10.1 9.3 9.74 FH43BW-51S-0.2SHW(**) 580-2814-1 ** 51 11.8 9.6 10 11.3 10.5 10.94 FH43BW-61S-0.2SHW(**) 580-2816-7 ** 61 13.8 11.6 12 13.3 12.5 12.94 FH43BW-71S-0.2SHW(**) 580-2819-5 ** 71 15.8 13.6 14 15.3 14.5 14.94 4.94 5 FH43BW/FH43MW Series●0.2mm/0.25mm Pitch, 0.9mm Height FPC Connectors 0.25 0.5 0.5 Nov.1.2022 Copyright 2022 HIROSE ELECTRIC CO., LTD. All Rights Reserved. 0.07±0.02 ＋0.04 0.27 −0.03 (ｎ-１)/２× j 0.02 Z 9 0.72±0.07 B 9 H±0.05 R Enlarged figure Ｕ Ｖ (0.07) (0.35) : Shows recommended demension when lead for plating is required. : Indicated tolerance is applicable to the exposed conductor. : Dimension Q must be 0.5mm minimum. (Reference shape) Check mark for press misalignment (0.5) Note 8 9 10 Ｓ 0.01±0.02 Product No. HRS No. No. of Contacts A B FH43MW-17S-0.25SHW(**) 580-2817-0 ** 17 5.8 FH43MW-19S-0.25SHW(**) 580-2823-2 ** 19 6.3 FH43MW-41S-0.25SHW(**) 580-2824-5 ** 41 11.8 FH43MW-55S-0.25SHW(**) 580-2818-2 ** 55 15.3 3.1±0.3 （Stiffener） Contact No.2 0.1±0.15 R0.2±0.1 R0.2MAX 10 Ｑ R0.2MAX R0.2±0.1 （0.1 : Even pattern） （0.15 : Odd pattern） 9 0.72±0.07 0.2±0.02 1.55±0.15 2.1±0.3 8 0.1±0.03 8 0.1±0.03 8 0.07±0.02 Ｚ (ｎ+１)/２× j 0.02 Z R0.2MAX Contact No.1 0.27 ＋0.04 −0.03 1.6±0.05 1.1±0.05 Ｒ 0.25±0.07 C±0.02 (0.01) ※Relative positions of point-S and T : 0.05MAX 0.25±0.07 A±0.1 (F) G±0.05 (0) ※Relative positions of point-U and V [FH43MW] 0.74±0.1 （Even pattern） 0.75±0.1 （Odd pattern） 1.45±0.1 0.75±0.1 （Odd pattern） 0.76±0.1 （Even pattern） BRecommended FPC Pattern Ｔ Unit : mm H C F G 3.5 4 5.3 4.5 4.94 4 4.5 5.8 5 5.44 9.5 10 11.3 10.5 10.94 13 13.5 14.8 14 14.44 BFPC Material Configuration (Reference Example) Single-Sided FPC Material name Material Covering film layer Polyimide 1 mil Thickness (µm) （２５） Cover adhesive Surface treatment 1µm to 6µm Nickel underplated + 0.2µm Gold plated 4 12 Copper foil Cu  1/3 oz Base adhesive Heat-hardened adhesive No adhesion material Base film Polyimide 1 mil 25 Reinforcement material adhesive Heat-hardened adhesive 30 Stiffener Polyimide 5 mil 125 Total 196 Precautions 1. This specification is a recommendation for the construction of the FH43BW/FH43MW Series FPC (t=0.2±0.02). 2. For details about the construction, please contact the FPC manufacturers. 6 （２５） FH43BW/FH43MW Series●0.2mm/0.25mm Pitch, 0.9mm Height FPC Connectors BPackaging Specifications ●Reel Condition Dimensions Ｋ±0.1 +0.15 +0.1 Ø1.5 0 Ø1.7 0 Direction of unreeling Ｊ±0.3 Ｌ±0.1 1.75±0.1 +0 0 .1 (2) ●Leader, Trailer Dimensions (M : Inside) (Ø13) 400mm MIN (Leader) Direction of unreeling (Ø380) (Ø80) Nov.1.2022 Copyright 2022 HIROSE ELECTRIC CO., LTD. All Rights Reserved. Ｌ±0.1 (2) 4±0.1 Ｊ±0.3 4±0.1 (0.3) 1.75±0.1 +0 0 .1 (0.3) 8±0.1 (1.2) 8±0.1 Ø1 .5 (1.2) ●Embossed Carrier Tape Dimension (Tape width : 32mm MIN) Ø1 .5 ●Embossed Carrier Tape Dimension (Tape width : 24mm MAX) 160mm MIN (Trailer, Empty) Embossed carrier tape 100mm MIN (Empty) Top cover tape (N : Outside) Unit : mm Product No. HRS No. No. of Contacts J K L M N FH43BW-21S-0.2SHW(**) 580-2822-0 ** 21 16 - 7.5 17.4 21.4 FH43BW-25S-0.2SHW(**) 580-2830-0 ** 25 16 - 7.5 17.4 21.4 FH43BW-31S-0.2SHW(**) 580-2820-4 ** 31 16 - 7.5 17.4 21.4 FH43BW-35S-0.2SHW(**) 580-2821-7 ** 35 24 - 11.5 25.4 29.4 FH43BW-41S-0.2SHW(**) 580-2813-9 ** 41 24 - 11.5 25.4 29.4 FH43BW-45S-0.2SHW(**) 580-2815-4 ** 45 24 - 11.5 25.4 29.4 FH43BW-51S-0.2SHW(**) 580-2814-1 ** 51 24 - 11.5 25.4 29.4 FH43BW-61S-0.2SHW(**) 580-2816-7 ** 61 24 - 11.5 25.4 29.4 FH43BW-71S-0.2SHW(**) 580-2819-5 ** 71 32 28.4 14.2 33.4 37.4 Product No. HRS No. No. of Contacts J K L M N FH43MW-17S-0.25SHW(**) 580-2817-0 ** 17 16 - 7.5 17.4 21.4 FH43MW-19S-0.25SHW(**) 580-2823-2 ** 19 16 - 7.5 17.4 21.4 FH43MW-41S-0.25SHW(**) 580-2824-5 ** 41 24 - 11.5 25.4 29.4 FH43MW-55S-0.25SHW(**) 580-2818-2 ** 55 24 - 11.5 25.4 29.4 7 FH43BW/FH43MW Series●0.2mm/0.25mm Pitch, 0.9mm Height FPC Connectors BTemperature Profile MAX 250ç 250 Temperature (ç) 230ç 200 200ç 150 150ç Applicable Conditions Reflow method：IR/Hot air Reflow environment ：Room air Solder ：Paste type Sn/3.0Ag/0.5Cu (M705-GRN360-K2-V made by Senju Metal Industry Co.) Test PCB ：PCB material and size Glass epoxy 100×72.5×0.8mm Land pattern 0.2×0.65, 0.2×0.87mm Stencil ：Thickness 0.1mm Opening size 0.18×0.55, 0.18×0.68mm 100 Nov.1.2022 Copyright 2022 HIROSE ELECTRIC CO., LTD. All Rights Reserved. 50 25ç （60sec） 0 90∼120sec Pre-heating Start Time (sec) 8 （60sec） Soldering The temperature profiles are based on the above conditions. In individual applications the actual temperature may vary, depending on solder paste type, volume/thickness and board size/thickness. Consult your solder paste and equipment manufacturer for specific recommendations. FH43BW/FH43MW Series●0.2mm/0.25mm Pitch, 0.9mm Height FPC Connectors BOperation and Precautions Operation Methods This connector needs to be handled with care due to its thin design and miniature stature. Please refer to the following descriptions for handling precautions. 1. Initial Delivery Condition Nov.1.2022 Copyright 2022 HIROSE ELECTRIC CO., LTD. All Rights Reserved. ❶ The connector is delivered with the actuator closed. ［Caution］ ・Do not insert FPC or operate actuator before mounting. 2. How to unlock ❶ Rotate slowly flip up the actuator to release the lock. ［Caution］ ・When operating the actuator do not apply any force in the direction of the connector. ・The actuator rotates 125 degrees max. Do not attempt to force the actuator to backside further. PCB PCB Failure from the actuator pushed in - Incorrect Operation - PCB - Incorrect Operation - 3. How to insert FPC ❶ This connector has contacts on the bottom. Insert the FPC with the exposed conductors face down. ［Caution］ ・Insert the FPC with the actuator opened. ・This connector utilizes metal fittings designed to align the FPC. ・Do not twist the FPC to up and down, right and left or an angle. 12 5° 15° FPC contact side is down Metal fitting for positioning FPC 9 FH43BW/FH43MW Series●0.2mm/0.25mm Pitch, 0.9mm Height FPC Connectors Operation Methods 4. FPC insertion check ❶ Metal fittings guide the FPC tabs to the correct position. Make sure that the FPC tabs are located in correct position as shown in the figure below after FPC insertion. ［Caution］ ・Do not insert the FPC at an angle and/or stop it before insertion is completed. Nov.1.2022 Copyright 2022 HIROSE ELECTRIC CO., LTD. All Rights Reserved. FPC TAB FPC(Insufficient inserted) Metal fitting - Incorrect Operation - - Correct Operation - Hook of metal fittings fits in FPC TAB. FPC(Inserted with angle) FPC TAB run on the metal fittings. - Incorrect Operation - FPC TAB run on the metal fittings. 5. How to lock ❶ Apply load to rotate the actuator after inserting the FPC. ［Caution］ ・The actuator rotates on its axis. Make sure to operate the actuator with a rotating motion. ・In order to lock the actuator, apply force to the center of the actuator. ・Do not operate the actuator at one end only. ・Do not apply excessive force during this operation, the lock. Close the actuator at the center. - Correct Operation - 10 Do not operate the actuator at one end only. - Incorrect Operation - FH43BW/FH43MW Series●0.2mm/0.25mm Pitch, 0.9mm Height FPC Connectors Operation Methods 6. Mating confirmation of the FPC ❶ This connector uses reinforced metal fittings to align the FPC. Visually confirm the FPC positioning after closing the actuator. ［Caution］ ・Do not insert the FPC at an angle and/or stop it before insertion is completed. - Correct mating process - - Incomplete insertion Window is not fully covered by FPC when FPC is miss-inserted. and FPC tabs extend from the connector. FPC fully fills window when FPC is correctly inserted. Nov.1.2022 Copyright 2022 HIROSE ELECTRIC CO., LTD. All Rights Reserved. - Diagonal insertion Window is not fully covered by FPC when FPC is miss-inserted. and FPC tabs extend from the connector. Check window FPC FPC TAB FPC(Inserted with angle) FPC(Insufficient inserted) 7. FPC Withdrawal (Unlock) ❶ Rotate slowly flipup the actuator to release the lock. ❷ After rotating the actuator to the fully opened position carefully withdraw the FPC pulling out at about 15 degree angle to the PCB mounting surface. ［Caution］ ・Open the actuator by carefully lifting it at the center. ・Do not operate the actuator at one end only. Actuator (Close) PCB - Correct Operation - PCB - Incorrect Operation - 8. FPC routing after connecting ❶ Depending on a FPC rounding, a load is applied to the connector, and a contact failure may occur. To prevent a failure, take the following notes into a consideration during mechanism design. ［Caution］ ・Make sure that the FPC and its stiffener do not contact chassis. ・Avoid applying forces to FPC in vertical or horizontal directions. In addition, avoid pulling up and down on the FPC. ・ When fixing FPC after FPC cabling, avoid pulling FPC, and route the wire FPC with slack. In this regard, the stiffener is parallel to the PCB. ・Do not mount other components touching to the FPC underneath the FPC stiffenner. 11 FH43BW/FH43MW Series●0.2mm/0.25mm Pitch, 0.9mm Height FPC Connectors Cautions when Mounting PCB 使用上の注意点 Stiffener film Stiffener film PCB PCB PCB Nov.1.2022 Copyright 2022 HIROSE ELECTRIC CO., LTD. All Rights Reserved. Component part Stiffener film S Warp of PCB Minimize warp of the PCB as much as possible. Lead co-planarity including reinforced metal fittings is 0.1 mm or less. Too much warp of the PCB may result in a soldering failure. S Flexible board design Please make sure to put a stiffener on the backside of the flexible board. We recommend a glass epoxy material with the thickness of 0.3 mm MIN. S Load to Connector Do not add 0.5N or greater external force when unreel or pick and place the connector etc, or it may get broken. In addition, do not insert the FPC or operate the connector before mounting. S Load to PCB ・Splitting a large PCB into several pieces ・Screwing the PCB Avoid the handling described above so that no force is exerted on the PCB during the assembly process. Otherwise, the connector may become defective. Connector FPC(For connector mounting) S Instructions on manual soldering Follow the instructions shown below when soldering the connector manually during repair work, etc. ❶ Do not perform manual soldering with the FPC inserted into the connector. ❷ Do not heat the connector excessively. Be very careful not to let the soldering iron contact any parts other than connector leads. Otherwise, the connector may be deformed or melt. ❸ Do not supply excessive solder (or flux). If excessive solder (or flux) is supplied on the terminals, solder or flux may adhere to the contacts or rotating parts of the actuator, resulting in poor contact or a rotation failure of the actuator. Supplying excessive solder to the metal fittings may hinder actuator rotation, resulting in breakage of the connector. 2-6-3,Nakagawa Chuoh,Tsuzuki-Ku,Yokohama-Shi 224-8540,JAPAN https://www.hirose.com/ 12 The characteristics and the specifications contained herein are for reference purpose. Please refer to the latest customer drawings prior to use. The contents of this catalog are current as of date of 09/2021. Contents are subject to change without notice for the purpose of improvements.