unipole & multipole
connectors
No reproduction or use without express permission of editorial or pictorial content, in any manner.
LEMO reserve the right at all times to modify and improve specifications without any notification.
®
®
LEMO unipole and multipole connectors
This catalogue gives the complete description of LEMO unipole and multipole type connectors. The LEMO manufacturing
programme has been extended to almost 40 series divided into 7 product families with specific mating and environmental characteristics. Each series includes a wide variety of plug, socket, coupler and bridge plug models, available in
contact configurations adapted to all round cables, including up to 114 conductors, and a maximum diameter of 30 mm.
Watertight and vacuumtight models are also available. Since LEMO connectors are perfectly screened and designed to
guarantee very low resistance to shell electrical continuity, they are particularly adapted to applications where electromagnetic compatibility (EMC) is important.
Table of Contents
3 steps to select the right connector................................................................................................................................................................................. 3
B Series (indoor, keyed)
Interconnections..................................................................................................................................................................................................... 12
Part Numbering system ......................................................................................................................................................................................... 13
Metal Housing models............................................................................................................................................................................................ 14
Elbow socket models.............................................................................................................................................................................................. 25
Plastic housing models........................................................................................................................................................................................... 28
Watertight or vacuumtight models.......................................................................................................................................................................... 30
Bridge models......................................................................................................................................................................................................... 34
Threaded-latching models...................................................................................................................................................................................... 35
Alignment Key and Polarized Keying System......................................................................................................................................................... 36
K Series (outdoor, keyed)
Interconnections..................................................................................................................................................................................................... 37
Part Numbering system.......................................................................................................................................................................................... 38
Metal Housing models............................................................................................................................................................................................ 39
Watertight or vacuumtight models.......................................................................................................................................................................... 47
Alignment Key and Polarized Keying System......................................................................................................................................................... 49
T Series (outdoor, keyed)
Interconnections..................................................................................................................................................................................................... 50
Part Numbering system.......................................................................................................................................................................................... 51
Metal Housing models............................................................................................................................................................................................ 52
Watertight or vacuumtight models.......................................................................................................................................................................... 55
Plastic housing models........................................................................................................................................................................................... 56
B, K and T Series Insert configuration, Housings, Insulators, Contacts, Collets, Variant..................................................................................... 57
S Series (indoor, stepped insert)
Interconnections..................................................................................................................................................................................................... 74
Part Numbering system ......................................................................................................................................................................................... 75
Metal Housing models............................................................................................................................................................................................ 76
Elbow socket models.............................................................................................................................................................................................. 87
Plastic housing models........................................................................................................................................................................................... 89
Watertight or vacuumtight models.......................................................................................................................................................................... 91
E Series (outdoor, stepped insert)
Interconnections..................................................................................................................................................................................................... 93
Part Numbering system.......................................................................................................................................................................................... 94
Metal Housing models............................................................................................................................................................................................ 95
Watertight or vacuumtight models........................................................................................................................................................................ 101
S, and E Series Insert configuration, Housings, Insulators, Contacts, Collets, Variant....................................................................................... 103
M Series (outdoor, keyed)............................................................................................................................................................................................... 123
F Series (outdoor, keyed)............................................................................................................................................................................................... 125
Spare parts....................................................................................................................................................................................................................... 127
Accessories..................................................................................................................................................................................................................... 137
Tooling.............................................................................................................................................................................................................................. 151
Panel cut-outs and PCB drilling pattern........................................................................................................................................................................ 157
Cable assembly (B, K, T, S and E series)........................................................................................................................................................................ 169
Technical characteristics................................................................................................................................................................................................ 182
Product safety notice...................................................................................................................................................................................................... 198
www.lemo.com
1
®
®
Precision modular connectors to suit your application
Since its creation in Switzerland in 1946 the LEMO Group has been recognized as a global leader of circular Push-Pull
connectors and connector solutions. Today LEMO and its affiliated companies, REDEL and COELVER, are active in
more than 80 countries with the help of over 40 subsidiaries and distributors.
Over 75000 connectors
The modular design of the LEMO range provides over 75000 connectors from miniature ø 3 mm to ø 50 mm, capable of
handling cable diameters up to 30 mm and for up to 114 contacts. This vast portfolio enables you to select the ideal connector configuration to suit almost any specific requirement in most markets, including medical devices, test and measurement instruments, machinery, audio video broadcast, telecommunications and military.
LEMO’s Push-Pull Self-Latching Connection System
This self-latching system is renowned worldwide for its easy and quick mating and unmating features. It provides absolute
security against vibration, shock or pull on the cable, and facilitates operation in a very limited space.
The LEMO self-latching system allows the connector
to be mated by simply pushing the plug axially into
the socket.
Once firmly latched, connection cannot be broken by
pulling on the cable or any other component part other
than the outer release sleeve.
When required, the connector is disengaged by a
single axial pull on the outer release sleeve.
This first disengages the latches and then withdraws
the plug from the socket.
UL Recognition
LEMO connectors are recognized by the Underwriters Laboratories (UL). The approval of the complete system (LEMO
connector, cable and your equipment) will be easier because LEMO connectors are recognized.
CE marking
CE marking
means that the appliance or equipment bearing it complies with the protection requirements of one or
several European safety directives. CE marking
applies to complete products or equipment, but not to electromechanical components, such as connectors.
RoHS
LEMO connector specifications conforms the requirements of the RoHS directive (2011/65/EU) of the European Parliament and the latest amendments. This directive specifies the restrictions of the use of hazardous substances in electrical
and electronic equipment marketed in Europe.
Product safety notice & disclaimers
Please read and follow all instructions specified on the last page or on our website carefully and consult all relevent
national and international safety regulations for your application. Improper handling, cable assembly, or wrong use of
connectors can result in hazardous situations.
LEMO products and services are provided “as is.” LEMO makes no warranties or representations with regard to LEMO
product & services or use of them, express, implied or statutory, including for accuracy, completeness, or security.
In no event shall LEMO be liable for any direct, indirect, punitive, incidental, special consequential damages, to property
or life, whatsoever arising out of or connected with the use or misuse of LEMO’s products.
2
www.lemo.com
®
®
3 steps to select the right connector
l
Step 1: Select connector series
Select the appropriate LEMO connector series according to the environmental parameters that will affect your device
or cable such as indoor, outdoor, temperature range, ingress protection of the mated connector and of your device.
Use the table shown on page 4.
.
Part number coding
l
Step 2: Select connector size
.
B, K, T, S or E
.
Use the section (mm2) or the AWG of your cable wire to select the optimal contact diameter (values vary between
solder, crimp or print contact), see page 8.
Use this optimal contact diameter to determine the right connector size as well as the insert configuration, see page 6.
.
Part number coding
l
Step 3: Complete the part number
.
0, 1, 2, 3, 4, 5 or 6
.
Now that you know the series, as well as the insulator configuration, complete the part numbering system with the help
of the following table.
.
Part number coding
.
Model
Series
Insert
configuration
K Series (outdoor, keyed)
39
39
57
S Series (indoor, stepped insert)
76
76
103
B Series (indoor, keyed)
T Series (outdoor, keyed)
E Series (outdoor, stepped insert)
14
53
95
Note: Figures in the above table refer to the catalogue pages.
www.lemo.com
14
53
95
57
57
103
.
Housing
material
64
64
64
112
112
Insulator
material
64
64
64
112
112
Contact
64
64
64
112
112
Collet
67
68
70
115
119
Variant
71
71
71
121
121
3
®
®
Step 1: Select Connector Series
LEMO unipole and multipole connectors
The standard keyed Series (B, 00)
The characteristic feature of these connector series is a keying system which allows higher contact density and prevents all
errors in alignment. The various keying alternatives prevent unwanted cross mating of otherwise similar connectors. It is
also possible to use crimp contacts to reduce cable assembly time. These connector series, include the 0B to 5B range as
well as the 00 multipole, some vacuumtight models are also available.
The watertight keyed Series (K, T)
These series are watertight when mated and assembled to an appropriate cable. They include the 0K to 5K series and the
TT to 3T series, available in the same types as the 0B to 5B series.
The standard Series (S, 00)
The characteristic feature of these connector series is the hermaphroditic insulator in the multipole version. They include
principally the 0S to 6S series, as well as the 00 unipole series.
The watertight Series (E)
These series are watertight when mated and assembled to an appropriate cable. They include the 0E to 6E series and are
available in the same types as the S series.
Series
Environment
Ingress protection 1)
Ingress protection 2)
00 multipole
B
outdoor or harsh environment
IP50 to IP68
vacuumtight
IP66 to IP68
vacuumtight
IP50
- 55 to 250°C
Shell sizes
8 metal
and 4 plastic
Insulator type
Contact type
Features
Page
T
indoor
Temperature range
Latching
K
13 keyways
11 to 36
IP66 to IP68
- 55 to 200°C
6 metal
Multipole
Solder, crimp or print
9 keyways
37 to 50
Push-Pull self-latching
5 metal
4 keyways
51 to 56
00 unipole
S
E
indoor
outdoor or
harsh environment
IP50 to IP68
vacuumtight
IP66 to IP68
vacuumtight
IP50
IP66 to IP68
- 55 to 250°C
- 55 to 200°C
7 metal
and 5 plastic
6 metal
Unipole or multipole
hermaphroditic
Solder, crimp or print
73 to 92
Stepped insert
93 to 102
Note:
1) Mated connector. See ingress protection code p. 5. 2) Your device. For selection of connectors for watertight and vacuumtight devices, see p. 5.
4
www.lemo.com
®
®
Definition of Ingress Protection (IP code)
IEC 60529 outlines an international classification system
for the sealing effectiveness of enclosures of electrical
equipment against the intrusion into the equipment of foreign bodies (i.e. tools, dust, fingers) and moisture. This
classification system utilizes the letters «IP» (Ingress Protection) followed by two digits.
Degrees of protection - First digit
The first digit of the IP code indicates the degree to which
persons are protected against contact with moving parts
and the degree that equipment is protected against solid
foreign bodies intruding into an enclosure.
Code
First digit description
No special protection
2
Protection against objects not greater than 80 mm in length
and 12 mm in diameter
3
4
5
6
7
8
IP letter code
1st digit
2nd digit
Protection from a large part of the body such as hand
or from solid objects greater than 50 mm in diameter
Protection from entry by tools, wires, etc.,
with a diameter or thickness greater than 2.5 mm
Protection from entry by solid objects
with a diameter or thickness greater than 1.0 mm
Protection from the amount of dust that would interfere
with the operation of the equipment
Dust-tight
–
0
The second digit indicates the degree of protection of the
equipment inside the enclosure against the harmful entry
of various forms of moisture (e.g. dripping, spraying, submersion, etc.)
Second digit description
0
No special protection
2
Protection from dripping water when tilted up to 15°
1
3
4
5
6
7
–
5
Degrees of protection - Second digit
Code
0
1
Example: IP 50 = IP
8
Protection from vertically dripping water
Protection from sprayed water
Protection from splashed water
Protection from water projected from a nozzle
Protection against heavy seas, or powerful jets of water
Protection against temporary immersion
Protection against complete continuous submersion in water
Selection of connectors for watertight or vacuumtight devices
LEMO B and S series are rated IP50 only when mated. LEMO E, K and T series are rated IP66 (and over) only when
mated. If a device must be watertight or vacuumtight when the connectors are unmated, it is important to select a watertight or vacuumtight socket. You can consider the following two situations:
A) Figure 1 shows a typical outdoor device. To ensure this
device retains IP66 or above when connectors are
unmated, it is important to choose a watertight socket
from B, S, E, K or T series.
Fig. 1
your device
FGG plug K series
EGG socket K series
B) Figure 2 shows a device which is subjected to pressure
difference such as a near vacuum or pressurized gas
and must exhibit no leakage. To ensure the device
maintains its sealing, the socket is additionally tested for
helium leakage (according MIL 1344A).
Fig. 2
Check temperature range (see section on pages 30, 47, 55, 91 and 101).
www.lemo.com
your device
FGG plug B series
HGG socket B series
epoxy
resin seal
5
®
®
Step 2: Select Connector Size
Select the right connector size and insert configuration
To be able to select the right connector size (0 to 6), it is important to define the contact diameter (ø A).
Find out the available contact diameter (ø A) of the LEMO connector depending on the number of contacts required and
depending on the rating required (see pages 57 to 63 and 103 to 111).
The following table shows the contact diameter (ø A).
2
302
0.5
0.9
1.3
2.0
3.0
3
303
0.5
0.9
1.3
1.6
2.0
4
304
0.5
0.7
0.9
1.3
2.0
5
305
0.35
0.7
0.9
1.3
1.6
6
306
0.35
0.5
0.7
1.3
1.6
2.0
7
307
0.5
0.7
1.3
1.6
2.0
8
308
0.7
0.9
1.3
0.5
0.9
1.3
1.6
0.7
0.9
1.3
Unipole
Multipole
6
4.0
6.0
6.0
6S-6E
112
4.0
5S-5E
1
4S-4E
160
3S-3E
1
2S-2E
140
1S-1E
1
0S-0E
3.0
00
130
5B-5K
1
4B-4K
2.0
3B-3K-3T
120
2B-2K-2T
116
1
XB
1
1B-1K-1T
113
0B-0K-0T
Insert configuration
1
00-TT
Number of contacts
Series
1.3
1.6
3.0
4.0
12.0
9
309
10
310
12
312
13
313
14
314
0.5
0.7
0.9
16
316
0.5
0.7
0.9
18
318
0.7
0.9
19
319
0.7
20
320
22
322
24
324
26
326
0.5
6.0
3.0
0.9
1.3
1.6
2.0
4.0
6.0
0.7
0.9
1.3
2.0
3.0
6.0/4.0
6.0
0.7
0.9
1.3
2.0
3.0
4.0
8.0
0.9/0.7
1.3
0.7
1.3
1.3
2.0
1.3/0.9
1.3
2.0/1.3
0.9
1.3
1.3
0.9
1.3
1.3
2.0
0.9
1.3
2.0
0.9
1.3
2.0
0.9
1.3
3.0/2.0
2.0
0.9
0.9
2.0
3.0
0.9
0.9
3.0/1.6
4.0
0.9
1.6
3.0
0.9
3.0/1.6
4.0
2.0/1.3 3.0/2.0 4.0/3.0
1.3/2.0
0.35
0.7
0.7
0.5
0.7
3.0
1.3
0.9
0.9
0.7
0.5
3.0
0.9
3.0
1.6
0.9
4.0/5.0
1.6
0.7
www.lemo.com
®
®
40
44
48
50
54
60
62
64
72
106
0.5
340
344
348
350
354
360
362
364
372
106
Note: 1) 2.0 is for 6S series, for 6E the values are 1.3 and 5.0.
www.lemo.com
0.7
1.3
0.7
1.3
0.9
0.9
0.9
1.3
1.3
1.3
1.3
1.3
6S-6E
5S-5E
4S-4E
3S-3E
2S-2E
1S-1E
0S-0E
1.3
00
0.9
5B-5K
0.7
4B-4K
3B-3K-3T
2B-2K-2T
336
XB
36
332
1B-1K-1T
330
0B-0K-0T
00-TT
30
32
Multipole
Insert configuration
Number of contacts
Series
2.0
2.0
2.01)
2.0
2.0
1.6
1.6
1.3
1.3
0.9
7
®
®
Verify the fitting to your wire
Verify if the selected contact diameter (ø A) of the LEMO connector fits to your cable wire diameter (AWG number or
max. available section).
Contact type
øA
(mm)
0.35
Solder
øA
0.9
0.806)
–
226)
1.40
–
16
2.0
1.80
øA
5.20
7.00
0.9
0.9
1.3
1.6
1.6
2.0
2.0
3.0
4.0
–
–
–
–
–
–
–
–
–
11.50
–
0.80
1
0.45
1.3
øC
5.20
0.7
0.7
øC
3.70
0.45
1.3
øA
2.70
0.55)
0.9
fig. 2
0.80
1.00
12.0
øC
0.457)
1.3
8.0
øA
0.09
24
6.0
øC
28
–
5.0
fig. 1
0.09
0.603)
4.0
øA
28
0.73)
3.0
Crimp
–
–
1.6
øC
0.40
0.402)
0.7
øC
øC
Form
(mm) per fig.
Solid
AWG Section
max.
max.
(mm2)
0.52)
0.5
øA
Contact
1.10
0.80
0.45
1.40
1.10
0.80
1.90
1.40
2.40
1.90
3.20
4.00
28
22
0.09
0.25
0.34
0.346)
Conductor
Stranded
AWG
Section (mm2)
min.
max.
min.
max.
–
30
–
0.05
–
–
–
–
1.50
–
10
–
–
–
–
6.00
–
–
–
–
–
–
–
–
–
–
–
–
0.50
16
–
1.50
12
10
8
8
4
0
–
–
–
2
–
–
32
28
26
224)
0.140
18
0.500
2
–
–
–
–
24
–
12
l
22
l
0.34
30
l
1.00
40
30
–
24
20
26
–
0.50
–
–
–
0.250
2
–
0.09
–
20
28
2
50.00
–
22
32
20
0.035
10.00
0.035
0.035
0.250
0.09
0.09
0.50
30
50
l
0.34
40
18
0.340
1.00
50
l
65
l
90
l
1.000
1.50
144)
1
–
–
16
124)
1.500
2.50
65
104)
2.500
4.00
75
2
–
–
18
14
1
–
–
12
10
1
–
–
14
l
0.140
18
22
l
224)
–
–
l
l
–
–
l
40
1
2
l
–
0.34
–
–
6.00
–
0.140
–
–
4.00
–
224)
2
1
–
21.00
28
–
1.00
–
–
–
–
10.00
–
–
0.346)
–
32
1
–
0.14
–
–
26
0.09
204)
–
–
–
–
0.34
1
–
0.05
–
18
14
–
224)
–
–
4.00
26
224)6)
0.50
10
28
–
20
1.00
30
Fr 1)
(N) Notes
1.000
4.000
1.50
6.00
l
l
l
Note:
1) contact retention force in the insulator (according to IEC 60512-8 test 15 a).
2) for 00/TT multipole series.
3) for S, E series.
4) for a given AWG, the diameter of some stranded conductor designs is larger than the solder cup diameter. Make sure that the maximum conductor
diameter is smaller than ø C.
5) for 00 /TT multipole series or for 0B/0T and 1B/1T series with male contacts.
6) for 0B.302/0B.303, 0K.302/0K.303 and 0T.302/0T.303 ø C = 1.0 mm, AWG max 20, section max (mm2) 0.50.
7) for 00/TT and 1B/1K/1T series, according to manufacturing and plating tolerance ø C min = 0.43 mm.
l First choice alternative
8
l Special order alternative
www.lemo.com
®
®
Verify the fitting to your wire
Verify if the selected contact diameter (ø A) of the LEMO connector fits to your cable wire diameter (AWG number or
max. available section).
Conductor
Solid
Stranded
AWG
Section (mm2)
Section
ø A
ø C Form
AWG
max.
(mm) (mm) per fig.
max.
min. max. min. max.
(mm2)
Contact
Contact type
Print
øA
L
Fr 1)
(N) Notes
øC
øA
øC
L dimensions and C are detailed in the section on PCB drilling pattern.
See page 163 and 167.
l
L dimensions and C are detailed in the section on PCB drilling pattern.
See page 164 and 168.
l
L
Print (elbow)
L
øA
øC
Note: 1) contact retention force in the insulator (according to IEC 60512-8 test 15 a).
Verify the fitting to your cable
Verify if the selected connector size fits to your cable diameter.
Cable diameter range (mm)
Series Collet
Cable diameter range (mm)
Collet for fitting
a bend relief
min. max. min. max.
Series Collet
Cable diameter range (mm)
Collet for fitting
a bend relief
min. max. min. max.
001)
1.4
3.5
1.4
3.5
0B
1.4
5.6
1.4
5.2
1B
2.2
7.6
2.2
XB
4.4
8.0
2B
1.4
9.9
3B
4.2
11.9
4.2 11.0
002) 1.3
4B
4.9
16.0
4.9 15.0
0S
5B
9.6
25.0
9.6 15.5
0K
1.0
5.0
1K
1.3
2K
TT
2.4 3.0
0T
1.0
6.53)
1.0 6.53)
7.2
1T
1.3
8.53)
4.4
7.0
2T
1.4
9.2
3T
Collet for fitting
a bend relief
min. max. min. max.
1.0
5.0 1.0
5.0
1E
1.3
8.53) 1.3
8.53)
1.3 8.53)
2E
1.3 10.53) 1.3 10.53)
1.3 10.53)
1.3 10.53)
3E
2.6 15.03) 2.6 15.03)
2.6 15.03)
2.6 15.03)
4E
4.8 23.53) 4.8 15.0
4.4 1.3 4.4
5E
9.6 23.5
–
–
1.3
6.23) 1.3 6.23)
6E
13.0
–
–
1S
1.4
8.73) 1.4 8.73)
1.0 5.0
2S
1.3 10.53) 1.3 10.53)
8.53)
1.3 8.53)
3S
2.6 13.03) 2.6 13.03)
1.3
10.53)
1.3 10.53)
4S
4.1 22.03) 4.1 13.0
3K
2.6
15.03)
2.6 15.03)
5S
6.1 30.0
–
–
4K
4.6
23.53)
4.6 15.0
6S
11.1
–
–
9.6
23.5
5K
2.4
3.0
Series Collet
30.0
0E
30.0
– –
Note:
1) for multipole only.
2) for unipole only.
3) for these series the maximum cable diameter require models with oversized cable collet (type K).
www.lemo.com
9
®
10
®
www.lemo.com
T SERIES (watertight)
K SERIES (watertight)
B SERIES
®
®
B Series
B series connectors provide the following main features:
– security of the Push-Pull self-latching system
– multipole types 2 to 64 contacts
– solder, crimp or print contacts (straight or elbow)
– high packing density for space savings
– multiple key options to avoid cross mating
– keying system («G» key standard)
of similar connectors for connector alignment
– 360° screening for full EMC shielding.
Metal housing models (page 14)
FAG
Fixed plugs
Straight plugs
Fixed sockets
FWG
FGG
EGG
EEG
FGG
ENG
JGG
EKG*
Free sockets
EZG
PHG
EFG
EYG
PHG
ECG
XPF*
PNG
Elbow plugs
FPG
Fixed sockets
FFG
FHG
ESG*
ECG
PKG
FNG
EHG
ECG
Fixed coupler
FMG*
FEG
EJG*
PFG
L•G
PEG
R••
FKG*
FDG
Elbow socket models (page 25)
FIG*
Elbow sockets
FSG
Note: * Contact LEMO for details.
Plastic housing models (page 28)
XBG, EXG
Bridge models (page 34)
Straight plugs
Fixed sockets
FGG
EPG
FGG
Plug with two
parallel sockets
Bridge plugs
ENG
FTG*
FGY
FGY
Watertight or vacuumtight models (page 30)
Fixed plug
Fixed sockets
HGG
Threaded-latching models (page 35)
Fixed coupler
HHG
CFF, CRG
ENY
Straight plugs
FVG
HEG
Fixed socket
ESG
Elbow socket
YHG
S••
HNG
12
HCG
HMG
FVB
XRB
www.lemo.com
®
Part Numbering System
®
F G G. 1 B . 3 0 6 . C L A D 6 2
Plug
P H G. 1 B . 3 0 6 . C L L D 6 2 Z
Free socket
Variant: (page 71)
Cable ø: (page 67)
Collet type: (page 67)
E G G. 1 B . 3 0 6 . C Y M
Fixed socket
R J G. 1 B . 3 0 6 . C L A
Coupler
Model: (page 14)
Variant: (page 71)
Alignment key: (page 36)
Contact: (page 64)
Series: (page 14)
Insulator: (page 64)
Insert configuration: (page 57)
Housing: (page 64)
FGG.1B.306.CLAD62 = straight plug with key (G) and cable collet, 1B series, multipole type with 6 contacts, outer shell in chrome-plated
brass, PEEK insulator, male solder contacts, D type collet for 6.0 mm diameter cable.
PHG.1B.306.CLLD62Z = free socket with key (G) and cable collet, 1B series, multipole type with 6 contacts, outer shell in chromeplated brass, PEEK insulator, female solder contacts, D type collet for 6.0 mm diameter cable and nut for fitting a bend relief.
EGG.1B.306.CYM = fixed socket, nut fixing, with key (G), 1B series, multipole type with 6 contacts, outer shell in chrome-plated brass,
PEEK extended insulator, female crimp contacts.
RJG.1B.306.CLA = straight fixed coupler with keys (J) at the flange end and key (G) at the other end, 1B series, multipole type with 6
contacts, outer shell in chrome-plated brass, PEEK insulator, male-female contacts.
Part Section Showing Internal Components
Fixed socket
1
2
3
4
5
6
7
outer shell
earthing crown
retaining ring
hexagonal nut
locking washer
insulator
female contact
www.lemo.com
7
6
2
3
4
5
1
1
6
5
4
2
7
Straight plug
3
1
2
3
4
5
6
7
outer shell
latch sleeve
collet nut
split insert carrier
insulator
male contact
collet
13
®
®
Metal housing models
Technical Characteristics
Electrical
Mechanical and Climatical
Characteristics
Endurance1)
Value
> 5000 cycles
Humidity
Standard
IEC 60512-5 test 9a
up to 95% at 60° C
Temperature range
- 55° C, + 250° C
Resistance to vibrations
10-2000 Hz, 15g IEC 60512-4 test 6d
Shock resistance
100 g, 6 ms
IEC 60512-4 test 6c
Salt spray corrosion test2)
> 1000h
IEC 60512-6 test 11f
Protection index (mated)
IP 50
IEC 60529
Climatical category
55/175/21
IEC 60068-1
Characteristics
Shielding
efficiency
Value
Standard
at 10 MHz
> 75 dB
IEC 60169-1-3
at 1 GHz
> 40 dB
IEC 60169-1-3
Note:
the various tests have been carried out with FGG and EGG connector
pairs, with chrome-plated brass shell and PEEK insulator.
Detailed electrical characteristics, as well as materials and treatment are
presented in the chapter Technical Characteristics on page 182.
1) see page 189, contact resistance after mating cycles. See page 185,
mechanical endurance latching force.
2) for chrome plated product (« C » material code).
FGG Straight plug, key (G) or keys (A…M and R), cable collet
Reference
Dimensions (mm)
Model Series A
~L
øA
~M
S2
S1
L
M S1 S2
FGG
001) 6.4 28.5 20.5 5.5 5
FGG
0B
9.5 36.0 26.0 8.0 7
FGG
1B
12.0 43.0 32.0 10.0
FGG
XB
13.0 44.0 33.5 11.0 10
FGG
2B
15.0 50.0 38.0 13.0 12
FGG
3B 18.0 58.0 43.0 15.0 14
FGG
4B
25.0 75.0 57.0 21.0 20
FGG
5B
35.0 103.0 78.0 31.0 30
9
M1 Cable assembly (page 169)
Note: 1) the surface design of the 00 series is different.
FGG Straight plug, key (G) or keys (A…M), cable collet and nut for fitting a bend relief 2)
Reference
Dimensions (mm)
Model Series A
~L
øA
~M
S2
S1
L
M S1 S2
FGG
001) 6.4 28.7 20.7 5.5 6
FGG
0B
9.5 35.0 25.0 8.0 7
FGG
1B
12.0 42.0 31.0 10.0
FGG
XB
13.0 47.5 37.0 11.0 10
FGG
2B
15.0 49.0 37.0 13.0 12
FGG
3B
18.0 56.5 41.5 15.0 15
FGG
4B
25.0 71.0 53.0 21.0 20
9
M1 Cable assembly (page 169)
Note: 1) the surface design of the 00 series is different.
Note: 2) to order, add a «Z» at the end of the reference.
The bend relief must be ordered separately (see page 145).
14
www.lemo.com
®
®
JGG
Straight plug, short version, key (G), cable collet
~L
øA
~M
S2
FFG
S1
Model
Series
JGG
0B
A
9.5
Dimensions (mm)
L
32
M
22
M4 Cable assembly (page 171)
Straight plug, non-latching, key (G) or keys (A…M), cable collet
Reference
~L
øA
~M
S2
FNG
Reference
S1
Model
Series
FFG
0B
FFG
1B
FFG
2B
FFG
3B
FFG
4B
A
L
S2
32
10
9
43
15
15.0
50
38
25.0
58
75
7
S1
26
43
S2
M
36
18.0
8
Dimensions (mm)
9.5
12.0
S1
57
M1 Cable assembly (page 169)
8
7
13
12
21
20
14
Straight plug, key (G) or keys (A…M and R), cable collet and lanyard release
Reference
~L
S2
www.lemo.com
S1
Series
FNG
0B
FNG
1B
FNG
2B
FNG
3B
FNG
4B
FNG
5B
B
N
øA
~M
Model
A
B
Dimensions (mm)
L
M
N
S1
S2
140
10
9
190
15
9.5 15.5
36.0 26.0
140
15.0 21.0
49.0 37.0
160
12.0 18.0
18.0 25.0
25.0 32.0
43.0 32.0
58.0 43.0
75.0 57.0
35.0 42.0 103.0 78.0
M1 Cable assembly (page 169)
230
300
8
7
13
12
21
20
31
14
30
Note: cable material: stainless steel with Polyamide sheath.
15
®
®
FEG
Straight plug, key (G) or keys (A…L), cable collet, front seal and nut for fitting a bend relief 1)
(IP 54 protection index when mated)
Reference
~L
øA
~M
S2
FDG
Model
Series
FEG
0B
FEG
1B
FEG
2B
FEG
3B
A
Dimensions (mm)
L
M
S1
S2
13.5 42.0 33.0
10
9
19.0 56.5 41.5
15
11.0 35.0 25.0
16.5 48.0 36.0
M1 Cable assembly (page 169)
S1
8
13
7
12
15
Note: 1) to order, add a «Z» at the end of the reference.
The bend relief must be ordered separately (see page 145).
Straight plug, long version, key (G) or keys (A…L), cable collet
Reference
~L
øA
~M
S2
S1
FWG Fixed plug, nut fixing, key (G) or keys (A…L)
N
øA
M
e
øB
E maxi
S1
Series
FDG
1B
FDG
2B
A
12
15
L
68
79
M
S1
S2
67
13
12
57
M2 Cable assembly (page 171)
Reference
L maxi
S3
Model
Dimensions (mm)
Model
Series
FWG
0B
FWG
1B
FWG
2B
FWG
3B
A
B
14.0 12.4
e
10
9
Dimensions (mm)
E
L
M
N1)
M9x0.6 1.8 22.5 14.5 19.5
S1
S3
8.2 11
18.0 15.8 M12x1.0 2.9 24.9 17.0 24.8 10.5 14
19.5 19.2 M15x1.0 4.1 28.6 18.0 27.3 13.5 17
25.0 25.0 M18x1.0 4.2 32.1 23.0 31.5 16.5 22
P9 Panel cut-out (page 157)
Note: 1) maximum length with crimp contacts
16
www.lemo.com
®
®
FAG Fixed plug, non-latching, nut fixing, key (G) or keys (A…M and R)
Dimensions (mm)
Reference
Model Series A B
L maxi
N
øA
M
e
øB
S3
E maxi
S1
e
E L M N1) S1 S3
FAG
00
FAG
0B
10 12.4 M9x0.6 4.2 20.8 11.5 18.9 8.2 11
FAG
1B
14 15.8 M12x1.0 5.4 25.2 12.5 21.6 10.5 14
FAG
2B
18 19.2 M15x1.0 6.0 28.7 13.8 23.9 13.5 17
FAG
3B
22 25.0 M18x1.0 5.8 32.1 17.0 30.2 16.5 22
FAG
4B
29 34.0 M25x1.0 6.8 37.1 20.5 34.7 23.5 30
FAG
5B
40 40.0 M35x1.0 6.8 47.1 28.0 42.8 33.5 –
8 10.2 M7x0.5 2.9 18.1 9.0 15.0 6.3 9
P1 Panel cut-out (page 157)
Note: The 5B series is delivered without locking washer or tapered washer
and with a round nut.
Note: 1) maximum length with crimp contacts.
FPG Elbow (90°) plug, key (G) or keys (A…M and R), cable collet
M
Model Series A
~H
øA
S1
Dimensions (mm)
Reference
L
S3
S2
H
L
M S1 S2 S3
FPG
00
7.5 18 24.5 16.5 6.5 5
5.5
FPG
0B
9.5 23 30.0 20.0 8.0 7
8.0
FPG
1B
12.0 29 36.0 25.0 11.0
FPG
2B
15.0 35 41.5 29.5 13.5 12 13.0
9
10.0
M3 Cable assembly (page 169)
FHG Elbow (90°) plug, key (G) or keys (A…M and R), cable collet
L
S1
M
Dimensions (mm)
~H
øA
Reference
S3
S2
D
Model Series A
D
H
L
M S1 S2 S3
FHG
3B
19 10 37 50 35 17 14 15
FHG
4B
26 15 52 67 49 22 20 21
FHG
5B
36 21 74 90 65 32 30 31
M3 Cable assembly (page 169)
FSG Anglissimo right angle plug, key (G) or keys (A…M), cable collet
Dimensions (mm)
Reference
L
Model Series A
~H
øA
M
H
L
M S1 S2
FSG
00
8.0 18.1 24.8 16.8 5
7
FSG
0B
10.0 22.4 30.3 20.3
7
9
FSG
1B
12.0 26.4 36.5 25.5
9
11
S2
FSG
2B
16.5 34.5 44.0 32.0 12
15
S1
FSG
3B
20.0 39.2 52.4 37.4 14
19
M5 Cable assembly (page 170)
www.lemo.com
17
®
®
EGG Fixed socket, nut fixing, key (G) or keys (A…M and R)
Reference
Model
Series
EGG
00
EGG
0B
EGG
1B
EGG
XB
L maxi
N
M
øA
e
øB
S3
S1
E maxi
EGG
2B 2)
EGG
3B
EGG
4B
EGG
5B
A
8
B
10.2
10 12.4
e
Dimensions (mm)
M7x0.5
M9x0.6
14 15.8 M12x1.0
16 19.0 M14x1.0
18 19.2 M15x1.0
E
L
M
N1)
6.0 15.5 1.0 13.7
7.0 20.7 1.2 19.1
S1
6.3
S3
9
8.2 11
7.5 23.0 1.5 21.1 10.5 14
7.0 23.5 1.5 20.0 12.5 17
8.5 26.7 1.8 24.6 13.5 17
22 25.0 M18x1.0 11.5 30.7 2.0 28.1 16.5 22
28 34.0 M25x1.0 12.0 35.7 2.5 34.1 23.5 30
40 40.0 M35x1.0 11.0 43.5 3.0 39.6 33.5
P1 Panel cut-out (page 157)
–
Note: The 5B series is delivered with a tapered washer and a round nut.
Note: 1) maximum length with crimp contacts.
EGG.2B.304.CLL and EGG.2B.307.CLL are UL 508A under file E119802.
2)
ENG Fixed socket with earthing tag, nut fixing, key (G) or keys (A…M)
Reference
L maxi
N
M
øA
e
øB
S3
E maxi
S1
A
Model
Series
ENG
00
ENG
0B
ENG
1B2)
10 12.4
ENG
2B
ENG
3B
18 19.2 M15x1.0
ENG
4B
8
B
10.2
e
Dimensions (mm)
M7x0.5
M9x0.6
14 15.8 M12x1.0
E
L
M
N1)
6.0 15.5 1.0 13.7
7.0 20.7 1.2 19.1
S1
6.3
S3
9
8.2 11
7.5 23.0 1.5 21.1 10.5 14
8.5 26.7 1.8 24.6 13.5 17
22 25.0 M18x1.0 11.5 30.7 2.0 28.1 16.5 22
28 34.0 M25x1.0 12.0 35.7 2.5 34.1 23.5 30
P1 Panel cut-out (page 157)
Note:
1) maximum length with crimp contacts.
2) for the 1B series the earthing tag is on the same side of the key.
EHG Fixed socket, nut fixing, key (G) or keys (A…M and R), and protruding shell
Reference
L maxi
N
øA
M
e
øB
S3
E maxi
S1
Model
Series
EHG
00
EHG
0B
EHG
1B
EHG
2B
EHG
3B
EHG
5B
A
8
B
10.2
10 12.4
e
Dimensions (mm)
E
L
M7x0.5 2.0 15.5
M
N1)
8.5 13.7
M9x0.6 2.0 19.5 12.5 19.1
S1
6.3
S3
9
8.2 11
14 15.8 M12x1.0 4.0 21.7 12.0 21.1 10.5 14
18 19.2 M15x1.0 5.1 22.7 12.5 24.6 13.5 17
22 25.0 M18x1.0 7.1 30.7 13.5 30.3 16.5 22
40 40.0 M35x1.0 2.5 43.5 28.0 38.5 33.5
P1 Panel cut-out (page 157)
–
Note: The 5B series is delivered without locking washer or tapered washer
and with a round nut.
Note: 1) maximum length with crimp contacts.
18
www.lemo.com
®
®
EEG
Fixed socket, nut fixing, key (G) or keys (A…M and R) (back panel mounting)
Reference
L maxi
N
P
e
øB
øA
M
S1
S2
Model
Series
EEG
00
EEG
0B
EEG
1B
EEG
2B
EEG
3B
EEG
4B
EEG
5B
A
10
B
Dimensions (mm)
e
E
L
M
N1)
P
S1 S2
9.5 M7x0.5 2.3 15.5 2.5 13.7 6.0 6.3 7.5
12 12.5 M9x0.6 2.4 20.7 2.5 19.1 6.3 8.2 9.0
16 16.0 M12x1.0 6.5 23.0 3.5 21.1 11.0 10.5 13.0
20 20.0 M15x1.0 4.3 26.7 3.5 24.6 9.0 13.5 15.0
24 25.0 M18x1.0 6.1 30.7 4.5 28.1 12.0 16.5 20.0
30 32.1 M25x1.0 10.6 35.7 4.5 34.1 16.5 23.5 26.0
41 40.0 M35x1.0 13.5 43.5 5.0 39.6 19.5 33.5 38.0
P1 Panel cut-out (page 157)
E maxi
Note: The 3B, 4B and 5B series are delivered with a conical nut.
The 5B series is delivered without locking washer or tapered washer.
EFG
Note: 1) maximum length with crimp contacts.
Fixed socket, nut fixing, key (G) or keys (A…M), with two flats on the shell and O-ring
(back panel mounting)
L maxi
N
P
Reference
øA
e
øB
M
Series
EFG
0B
A
B
e
12 12.5 M9x0.6
P2 Panel cut-out (page 157)
E maxi
S2
Model
Dimensions (mm)
E
L
M
N1)
P
S2
N1)
S1
S3
5.5 20.7 2.5 19.1
9
8
Note: 1) maximum length with crimp contacts.
ECG Fixed socket with two nuts, key (G) or keys (A…M and R) (back panel mounting)
Reference
L maxi
N
M
øA
e
øB
S3
S1
E maxi
Model
Series
ECG
00
ECG
0B
ECG
1B
ECG
XB
ECG
2B
ECG
3B
ECG
4B
ECG
5B
A
B
10 10.2
12 12.4
e
Dimensions (mm)
M7x0.5
M9x0.6
16 15.8 M12x1.0
18 19.0 M14x1.0
20 19.2 M15x1.0
24 25.0 M18x1.0
E
L
M
4.3 13.7 2.5 13.7
5.5 20.7 2.5 19.1
6.3
9
8.2 11
6.0 23.0 3.5 21.1 10.5 14
6.0 23.5 3.5 20.0 12.5 17
6.5 26.7 3.5 24.6 13.5 17
9.0 30.7 4.5 28.1 16.5 22
30 34.0 M25x1.0 10.0 35.7 4.5 32.6 23.5 30
41 40.0 M35x1.0
P1 Panel cut-out (page 157)
9.0 43.5 5.0 39.6 33.5
–
Note: The 3B, 4B and 5B series are delivered with a conical nut.
The 5B series is delivered with a tapered washer and a round nut.
Note: 1) maximum length with crimp contacts.
www.lemo.com
19
®
®
ECG Fixed socket with two nuts, key (G) or keys (A…F and R) and straight contact for printed circuit
(back panel mounting)
Dimensions (mm)
Reference
Model Series A B
L
N
M
øA
e
øB
S3
S1
E maxi
e
E M N S1 S3
ECG
00
10 10.2 M7x0.5 4.3 2.5 13.7 6.3 9
ECG
0B
12 12.4 M9x0.6 5.5 2.5 16.1 8.2 11
ECG
1B
16 15.8 M12x1.0 6.0 3.5 19.8 10.5 14
ECG
XB
18 19.0 M14x1.0 6.0 3.5 20.0 12.5 17
ECG
2B
20 19.2 M15x1.0 6.5 3.5 21.8 13.5 17
ECG
3B
24 25.0 M18x1.0 9.0 4.5 25.8 16.5 22
ECG
4B
30 34.0 M25x1.0 10.0 4.5 29.8 23.5 30
ECG
5B
41 40.0 M35x1.0 9.0 5.0 36.8 33.5 –
P1 Panel cut-out (page 157)
P15 PCB drilling pattern (page 160)
Note: The 3B, 4B and 5B series are delivered with a conical nut.
The 5B series is delivered with a tapered washer and a round nut.
Note: This contact type is available for Ell socket models fitted with
female contacts.
Length «L» depends on the number of contacts, see table on page 163.
ECG Fixed socket with two nuts, key (G) or keys (A…F) with elbow (90°) contact for printed circuit
(back panel mounting)
Dimensions (mm)
Reference
N
S1
20 mini
M
e
øB
S3
Model Series A B
øA
L
e
N
E M
max
S1 S3
ECG
0B
12 12.4 M9x0.6 5.5 2.5 18.3 8.2 11
ECG
1B
16 15.8 M12x1.0 6.0 3.5 20.3 10.5 14
ECG
2B
20 19.2 M15x1.0 6.5 3.5 22.3 13.5 17
ECG
3B
24 25.0 M18x1.0 9.0 4.5 27.8 16.5 22
E maxi
P1 Panel cut-out (page 157)
2
P17 PCB drilling pattern (page 164)
Note: The 3B series is delivered with a conical nut.
L lG Fixed socket, nut fixing, key (G) or keys (A…L)
Dimensions (mm)
Reference
Model Series A B
Red (GND)
Green (GND)
V+
(3.3-3.6 Vdc)
Blue (GND)
N
LlG 0B
19 18.0 M13x0.75 4.0 20.7 4 19.1 11.5 16
LlG 1B
22 20.2 M15x1.00 6.5 23.0 4 21.1 13.5 16
LlG 2B
25 27.0 M20x1.00 7.5 26.7 4 24.6 18.5 24
M
ø A + 0.1
0
øB
e
øA
L mini
E maxi
20
S1
E L M N S1 S2
Note: Only available with solder or crimp contacts.
LEG model is with LED flange, LNG model is with narrow LED flange and
LMG model is with single standby LED flange.
L
S2
e
AWG 28 / AWG 30
B + 0.1
0
Series
Dim. (mm)
A B L
0B
13.1 11.6 24
1B
15.1 13.6 26
2B
20.1 18.6 29
www.lemo.com
®
®
EZG Straight socket for printed circuit, key (G) or keys (A, B)
B
H
N
Reference
Dimensions (mm)
Model Series A
øA
ø 0.5
ø 0.7
3
EZG
K
00
B
H
K
N
6.8 7 5.08 7
14
P15 + P16 PCB drilling pattern (pages 160 and 163)
EZG Straight socket for printed circuit, key (G) or keys (A…F)
Dimensions (mm)
Reference
Model Series A
L
H
N
ø 2.2
øA
M 1.6
B
B
H
K
N
EZG
0B
9 10 7.62 8 15.0
EZG
1B
11 12 7.62 8 19.0
EZG
2B
14 15 10.16 9 22.5
P15 + P16 PCB drilling pattern (pages 160 and 163)
Note: Length «L» depends on the number of contacts, see page 163.
Add letter «B» at the end of the reference to order with integrated
harpoon pins (1.6 mm PCB thickness) (only for 0B and 1B series).
K
EYG Fixed socket for printed circuit, nut fixing, key (G) or keys (A…F) (back panel mounting)
Dimensions (mm)
Reference
Model Series A B C
N
L
9
S1
P
B
M
M 1.6
D
e
E M
N
P
S1
EYG
0B
12 10 12.5 7.62 M9x0.6 2.6 2.5 15.0 6.0 8.2
EYG
1B
14 12 16.0 7.62 M11x0.5 5.0 3.5 19.0 10.0 –
EYG
2B
20 15 19.5 10.16 M15x1.0 7.5 3.5 22.5 13.5 13.5
P1 Panel cut-out 0B and 2B series (page 157)
e
E maxi
øA
P10 Panel cut-out 1B series (page 157)
øC
ø 2.2
www.lemo.com
D
P15 + P16 PCB drilling pattern (pages 160 and 163)
Note: Length «L» depends on the number of contacts, see page 163.
Add letter «B» at the end of the reference to order with integrated
harpoon pins (1.6 mm PCB thickness) (only for 0B and 1B series).
21
®
®
PHG Free socket, key (G) or keys (A…M and R), cable collet
Reference
Dimensions (mm)
Model Series A
øA
~L
S2
S1
L S1 S2
PHG
001)
6.8 26.0 5.5 5
PHG
0B
9.5 35.5 8.0 7
PHG
1B
12.5 40.5 10.0
PHG
XB
13.0 46.0 11.0 10
PHG
2B
16.5 47.0 13.0 12
PHG
3B
19.0 56.0 15.0 14
PHG
4B
26.0 73.0 21.0 20
PHG
5B
36.0 99.0 31.0 30
9
M1 Cable assembly (page 169)
Note: 1) the surface design of the 00 series is different.
PHG Free socket, key (G) or keys (A…M), cable collet and nut for fitting a bend relief 2)
Reference
Dimensions (mm)
Model Series A
øA
~L
S2
S1
L S1 S2
PHG
001)
6.8 34.0 5.5 6
PHG
0B
9.5 34.5 8.0 7
PHG
1B
12.5 39.5 10.0
PHG
XB
13.0 49.5 11.0 10
PHG
2B
16.5 46.0 13.0 12
PHG
3B
19.0 54.5 15.0 15
PHG
4B
26.0 69.0 21.0 20
9
M1 Cable assembly (page 169)
Note: 1) the surface design of the 00 series is different.
Note: 2) to order, add a «Z» at the end of the reference.
The bend relief must be ordered separately (see page 145).
PNG Free socket, nut fixing, key (G) or keys (A…L and R), cable collet with lanyard release
Dimensions (mm)
Reference
Model Series A
S2
S1
B
N
øA
~L
B
L
N S1 S2
PNG
1B
12.4 18.4 40.5 140 10
9
PNG
2B
16.5 22.5 47.0 160 13
12
PNG
3B
19.0 26.0 56.0 190 15
14
PNG
4B
26.0 33.0 73.0 230 21
20
PNG
5B
36.0 43.0 99.0 300 31
30
M1 Cable assembly (page 169)
Note: cable material: stainless steel with Polyamide sheath.
22
www.lemo.com
®
®
PKG Fixed socket, nut fixing, key (G) or keys (A…M and R), cable collet
Dimensions (mm)
Reference
Model Series A B
~L
S3
øA
e
S2
øB
M
S1
E maxi
e
E L M S1 S2 S3
PKG
00
PKG
0B
10 12.4 M9x0.6 7.0 35.5 1.2 8.2 7
11
PKG
1B
14 15.8 M12x1.0 7.5 40.5 1.5 10.5 9
14
PKG
2B
18 19.2 M15x1.0 8.5 47.0 1.8 13.5 12 17
PKG
3B
22 25.0 M18x1.0 11.5 56.0 2.0 16.5 14 22
PKG
4B
28 34.0 M25x1.0 12.0 73.0 2.5 23.5 20 30
PKG
5B
40 40.0 M35x1.0 11.0 99.0 3.0 33.5 30
8 10.2 M7x0.5 6.5 26.0 1.0 6.3 5
9
–
P1 Panel cut-out (page 157)
M1 Cable assembly (page 169)
Note: the 5B series is delivered with a tapered washer and a round nut.
PFG Fixed socket, with two nuts, key (G) or keys (A…M and R), cable collet (back panel mounting)
Dimensions (mm)
Reference
Model Series A B
~L
M
S2
øA
e
øB
S3
S 1 E maxi
e
E L M S1 S2 S3
PFG
00
10 10.2 M7x0.5 5.3 26.0 2.5 6.3 5
9
PFG
0B
12 12.4 M9x0.6 5.0 35.5 2.5 8.2 7
11
PFG
1B
16 15.8 M12x1.0 5.0 40.5 3.5 10.5 9
14
PFG
2B
20 19.2 M15x1.0 6.5 47.0 3.5 13.5 12 17
PFG
3B
24 25.0 M18x1.0 9.0 56.0 4.5 16.5 14 22
PFG
4B
30 34.0 M25x1.0 11.0 73.0 4.5 23.5 20 30
PFG
5B
41 40.0 M35x1.0 10.0 99.0 5.0 33.5 30
–
P1 Panel cut-out (page 157)
M1 Cable assembly (page 169)
Note: the 3B, 4B and 5B series are delivered with a conical nut.
The 5B series is delivered with a tapered washer and a round nut.
PEG Fixed socket, nut fixing, key (G) or keys (A…L), cable collet (back panel mounting)
~L
P
S1
M
Dimensions (mm)
Reference
S2
E maxi
e
øA
øB
Model Series A B
e
E L M P S1 S2 S4
PEG
3B
24 25 M18x1.0 5.0 56 4.5 12 16.5 14 20
PEG
4B
32 34 M25x1.0 12.5 73 5.0 20 23.5 20 27
S4
P1 Panel cut-out (page 157)
M1 Cable assembly (page 169)
Note: this model has an o-ring on the flange.
www.lemo.com
23
®
®
Rll
Fixed coupler, nut fixing, key (G) or keys (A and J) at the flange end and keys (J, K or M) at the other end
L
S3
E maxi
Reference
Model
G
RGG
G
J
RJG
G
G
RGJ
J
A
RAK
K
G
RGM
M
Example
Plug with key G
RGJ
Plug with key J
Alignment key see page 36.
24
RGG1)
RGG2)
Series
0B
0B
RJG
0B
RGJ
0B
RAK
0B
RGM
0B
RGG3)
1B
RJG
1B
RGJ
1B
RJG
2B
RGJ
2B
RGJ
3B
RGJ
4B
Contacts
Type
A
B
Dimensions (mm)
e
E
L
S1
2.0
9.0 12
12
13.8 M10x0.75
8.0 34
2.0
male – female
12
13.8 M10x0.75
8.0 34
2.0
female – female
female – male
female – male
female – male
female – female
male – female
female – male
male – female
female – male
female – male
female – male
P4 Panel cut-out (page 157)
12
12
12
12
16
16
16
20
20
25
34
13.8 M10x0.75
13.8 M10x0.75
13.8 M10x0.75
13.8 M10x0.75
19.2 M14x1.00
19.2 M14x1.00
19.2 M14x1.00
8.0 43
8.0 34
8.0 34
8.0 34
8.5 47
8.5 39
8.5 39
21.5 M16x1.00 12.0 44
21.5 M16x1.00 12.0 44
27.0 M20x1.00 32.0 53
34.0 M25x1.00 50.0 65
S1
M
female – female
2.0
2.0
2.0
øB
e
øA
M
S3
9.0 12
9.0 12
9.0 12
9.0 12
9.0 12
2.5 12.5 17
2.5 12.5 17
2.5 12.5 17
4.0 15.0 19
4.0 15.0 19
4.0 18.5 24
4.0 23.5 30
Note:
1) only available with two contacts.
2) RGG.0B only available from 3 till 5 contacts.
3) RGG.1B only available till 7 contacts.
For this fixed coupler, the first contact type mentioned is always the one at the flange end. On request,
these couplers can be produced in other series, with other keys.
www.lemo.com
®
®
Elbow socket models
Technical Characteristics
Materials and Treatment
Types
Component
Material
Surface
Treat. (µm)
Cu Ni Au
PPS –
Housing
0B, 1B
1
302
2
2
1
00
2
1
2
0B, 1B
3
1
00
4
00
1
5
2
2
1
3
1
4
2
3
2
304
3
3
2
1
4
3
2
3
00
305
0B, 1B
4
1
5
4
2
3
0B, 1B
306
6
5
4
1
2
3
6
5
4
2
3
4
0B, 1B
7
1B
0B
1B
8
1
7
6
1
2
3
7
1
2
6
3
8
10 9 8 7 6
2
1
6
3
4
1
6
3
0.5 3 –
Insulator
PEEK –
Female contact
Bronze
Types
Model Series
5
7
4
5
5
1 8
2 9 7
3 10 6
4 5
314
1 10
2 11 9
3 12 14 8
4 13 7
5 6
7
11
2
Bronze
4
3
310
5
6
12345
1B
1
2
309
4
12
13
14
3
4
1
8
2
3 9 7
6
4
5
5
10
5
1
2
7
3 8 6
4 5
4
9
0B, 1B
308
5
9
8
307
1
2
Earthing crown
EPG-XBG
00
302-303-304-305
1.00 1.00
2.0
EPG-EXG
0B
302
1.45 1.20
4.5
EPG-EXG
0B
303
1.70 1.60
4.5
EPG-EXG
0B
304
1.30 1.10
4.5
EPG-EXG
0B
305
1.25 1.20
4.5
EPG-EXG
0B
306
1.25 1.20
2.5
EPG-EXG
0B
307
1.00 1.00
2.0
EPG-EXG
0B
309
0.60 0.50
1.5
EPG-EXG
1B
302
1.70 1.45
4.5
EPG-EXG
1B
303
1.60 1.85
4.5
EPG-EXG
1B
304
1.70 1.80
4.5
EPG-EXG
1B
305
1.30 1.55
4.5
EPG-EXG
1B
306
1.35 1.45
4.5
EPG-EXG
1B
307
1.45 1.45
2.0
EPG-EXG
1B
308
1.30 1.30
2.0
EPG-EXG
1B
310
1.00 1.00
1.5
1B
314
1.00 1.30
1.0
EPG
Note:
numbering sequence shown is for female contacts (G keying),
for inverted contacts please contact factory.
0.5 3 1.5
Electrical
3
0B, 1B
0.5 3 –
Note:
The surface treatment standards are as follows:
– Nickel: SAE AMS QQ N 290. – Gold: ISO 27874
1
303
Brass
Rated
current (A)1)
2
Type
1
Metallic parts
Test voltage
(kV rms)1)
Contact-shell
1
00
Series
0.5 3 –
Test voltage
(kV rms)1)
Contact-contact
Series
Brass
Note:
1) see calculation method, caution and suggested standard on page 190.
P18 PCB drilling pattern (page 165)
P19 PCB drilling pattern (page 165)
www.lemo.com
25
®
®
øA
12.7
EPG Elbow (90°) socket for printed circuit, key (G) or keys (A…F) (solder or screw fixing)
L
N
K
Dimensions (mm)
Part number
D
H
I
K
L
N
3
H
I
A
EPG.1B.314.NLN
ø 0.7
ø 0.6 M 1.6
11 21 7.7 14.3 19 36 15.4
P20 PCB drilling pattern (page 165)
D
Note: to replace the 4 ground pins by 4 screws (M1.6) add an «S» to the end of the
part number. (e.g.: EPG.1B.314.NLNS)
EPG Elbow (90°) socket for printed circuit, key (G) or keys (A…F) (solder, screw or harpoon fixing)
Dimensions (mm)
Part number
A
øA
L
N
R
6.8 11.5 3.5 7.0 8.7 19 7.1 5.08
EPG.0B.303.HLN
R
K
EPG.00.303.HLN
EPG.0B.302.HLN
K
I
EPG.00.305.HLN
N
H
EPG.00.302.HLN
EPG.00.304.HLN
L
D
EPG.0B.304.HLN
EPG.0B.305.HLN
9.0 14.6 6.7 12.6 13.3 25 11.7 7.62
EPG.0B.306.HLN
EPG.0B.307.HLN
EPG.0B.309.HLN
EPG.1B.302.HLN
H
I
EPG.1B.303.HLN
3.0 (00)
3.2 (0B-1B)
EPG.1B.304.HLN
ø 0.7
M 1.6
ø 0.5 (00)
ø 0.7 (0B-1B)
D
ø 2.2
EPG.1B.305.HLN
EPG.1B.306.HLN
11.0 16.6 7.5 14.0 13.3 27 12.6 7.62
EPG.1B.307.HLN
EPG.1B.308.HLN
EPG.1B.310.HLN
Note: In the 0B and 1B series, it is possible to replace the 4
ground pins by 4 screws (M1.6) add an «S» to the end of the
part number. (e.g.: EPG.0B.307.HLNS).
A second alternative is to add an «B» at the end of the part
number (EPG.0B.307.HLNB), the connector is delivered with
integrated harpoon pins for rapidly assembly (1.6 mm PCB
thickness).
26
P18 PCB drilling pattern 00 series (page 165)
P19 PCB drilling pattern 0B, 1B series (page 165)
www.lemo.com
®
®
EXG Elbow (90°) socket for printed circuit with two nuts, key (G) or keys (A…F) (solder, screw or harpoon fixing)
(back panel mounting)
XBG Elbow (90°) socket fixing nut for printed circuit, key (G) or keys (A, B) (back panel mounting)
Part number
Dimensions (mm)
A B D e E H I K L M N R
S3
XBG.00.302.HLN
XBG.00.303.HLN
10 10.2 11.5 M7x0.5 2.1 3.5 7.0 8.7 19 2.5 7.1 5.08 9
XBG.00.304.HLN
EXG.0B.302.HLN
EXG.0B.303.HLN
R
N
EXG.0B.304.HLN
K
L
S3
ø 0.5 (00)
ø 0.7 (0B-1B)
EXG.0B.306.HLN
EXG.0B.307.HLN
EXG.0B.309.HLN
øA
EXG.1B.303.HLN
EXG.1B.304.HLN
EXG.1B.305.HLN
øB
3.0 (00)
3.2 (0B-1B)
M 1.6
12 12.4 14.6 M9x0.6 4.5 6.7 12.6 13.3 25 2.5 11.7 7.62 11
EXG.1B.302.HLN
H
I
e
M
EXG.0B.305.HLN
E maxi
D
ø 2.2
EXG.1B.306.HLN
14 15.0 16.6 M11x0.5 4.5 7.5 14.0 13.3 27 3.5 12.6 7.62 13
EXG.1B.307.HLN
EXG.1B.308.HLN
EXG.1B.310.HLN
Note: In the 0B and 1B series, it is possible to replace the 4
ground pins by 4 screws (M1.6) add an «S» to the end of the
part number. (e.g.: EXG.0B.307.HLNS).
A second alternative is to add an «B» at the end of the part
number (EXG.0B.307.HLNB), the connector is delivered with
integrated harpoon pins for rapidly assembly (1.6 mm PCB
thickness).
P2 Panel cut-out 00, 0B series (page 157)
P10 Panel cut-out 1B series (page 157)
P18 PCB drilling pattern 00 series (page 165)
P19 PCB drilling pattern 0B, 1B series (page 165)
www.lemo.com
27
®
®
Plastic housing models
These connectors are particularly recommended for all applications requiring maximum electrical insulation when mated. The
design, including a latch sleeve and a metal earthing crown, guarantees EMC screening efficiency to meet most requirements.
Technical Characteristics
Mechanical and Climatical
Colour
Characteristics
Endurance1)
Humidity
Value
PSU
PEEK
natural (beige)
white or grey
> 5000 cycles
> 5000 cycles
Temperature range
- 50° C/+ 250° C
Resistance to solvents
very good
Sterilization
resistance2)
> 200 cycles
up to 95% at 60° C
Standard
PPSU
cream
–
> 5000 cycles
IEC 60512-5 test 9a
- 50° C/+ 150° C
- 50° C/+ 180° C
limited
good
~20 cycles
> 100 cycles
–
–
IEC 60601-1 § 44.7
–
Note: 1) see page 189, contact resistance after mating cycles. See page 185, mechanical endurance latching force. 2) Steam sterilization.
FGG Straight plug, key (G or J), cable collet, PEEK outer shell
~L
Reference
øA
~M
S2
Model
Series
FGG
0B
FGG
1B
FGG
3B
FGG
4B
Dimensions (mm)
A
L
M
11.0 37.4 27.4
S2
8
13.5 43.0 32.0
10
26.0 78.5 60.5
20
19.0 62.0 47.0
M1 Cable assembly (page 169)
15
FGG Straight plug, key (G or J), cable collet, PEEK outer shell and nut for fitting a bend relief 1)
~L
Reference
øA
~M
S2
Model
Series
FGG
1B
FGG
4B
Dimensions (mm)
A
L
M
13.5 42.2 31.2
26.0 83.2 65.2
M1 Cable assembly (page 169)
S2
10
20
Note on availability
for all collet type
only from collet M82 and up
Note: 1) to order, add a «Z» at the end of the reference.
The bend relief must be ordered separately (see page 145).
28
www.lemo.com
®
®
FGY
Straight plug, keys (Y), cable collet and PSU or PPSU outer shell
~L
Reference
øA
~M
S2
Model
Series
FGY
2B
FGY
3B
FGY
4B
Dimensions (mm)
A
L
M
16.5 50.5 39.5
19.0 58.0 43.0
26.0 76.2 58.2
M1 Cable assembly (page 169)
FGY
S2
13
15
20
Straight plug, keys (Y), cable collet and PSU or PPSU outer shell and nut for fitting a bend relief 1)
øA
~M
Reference
~L
S2
Model
Series
FGY
2B
FGY
3B
FGY
4B
Dimensions (mm)
A
L
M
16.5 49.5 38.5
19.0 56.5 41.5
26.0 74.4 56.4
M1 Cable assembly (page 169)
S2
Note on availability
13
only for collet M42 and up
20
only for collet D82 and up
15
only for collet D62 and up
Note: 1) to order, add a «Z» at the end of the reference.
The bend relief must be ordered separately (see page 145).
ENG Fixed socket with earthing tag, nut fixing, key (G or J), PEEK outer shell
Reference
L maxi
M
e
øA
øB
S3
N
E maxi
S1
Model
Series
ENG
0B
ENG
1B
ENG
3B
ENG
4B
A
B
11 12.5
e
Dimensions (mm)
M9x0.6
14 15.8 M12x1.0
E
L
M
N1)
6.4 20.7 1.8 16.5
S1
S3
8.2 11
7.5 23.0 1.5 21.1 10.5 14
22 25.0 M18x1.0 11.5 30.7 2.0 28.1 16.5 22
28 34.0 M25x1.0 12.0 35.7 2.5 32.6 23.5 30
P1 Panel cut-out (page 157)
Note: 1) maximum length with crimp contacts.
ENY
Fixed socket with earthing tag, nut fixing, keys (Y), PSU or PPSU outer shell
Reference
L maxi
M
e
øA
øB
S3
N
E maxi
S1
Model
Series
ENY
2B
ENY
3B
ENY
4B
A
B
e
Dimensions (mm)
18 19.2 M15x1.0
E
L
M
N1)
S1
S3
8.5 26.7 1.8 24.6 13.5 17
22 25.0 M18x1.0 11.5 30.7 2.0 28.1 16.5 22
28 34.0 M25x1.0 12.0 35.7 2.5 32.6 23.5 30
P1 Panel cut-out (page 157)
Note: 1) maximum length with crimp contacts.
Other models with plastic outer shell are available on request.
www.lemo.com
29
®
®
Watertight or vacuumtight models
These plug, socket and coupler models allow the device on which they are fitted to reach a protection index of IP68 as
per IEC 60529. They are fully compatible with plugs of the same series and are widely used for portable radios, military,
laboratory equipment, aviation, etc.
These models are identified by a letter «P» at the end of the reference.
Most of these models are also available in a vacuumtight version. Such models are identified by an additional letter «V» at
the end of the part number (certificate on request).
Epoxy resin is used to seal these models.
Technical Characteristics
Mechanical and Climatical
Characteristics
Endurance1)
Value
> 5000 cycles
Humidity
Characteristics
IEC 60512-5 test 9a
up to 95% at 60° C
Temperature range
Salt spray corrosion
Climatical category
Leakage rate
Standard
(He)2)
00 to 1B
- 20° C/+ 100° C
2B to 5B
- 20° C/+ 80° C
test4)
Maximum operating
pressure3)
Value
Standard
00
60 bar
IEC 60512-7 test 14d
0B
60 bar
IEC 60512-7 test 14d
1B
60 bar
IEC 60512-7 test 14d
2B
40 bar
IEC 60512-7 test 14d
3B
30 bar
IEC 60512-7 test 14d
> 1000h
IEC 60512-6 test 11f
20/80/21
IEC 60068-1
4B
15 bar
IEC 60512-7 test 14d
IEC 60512-7 test 14b
5B
5 bar
IEC 60512-7 test 14d
<
10-7
mbar.l.s-1
Note: 1) see page 189, contact resistance after mating cycles. See page 185, mechanical endurance latching force.
2) only for vacuumtight models. Residual traces of grease used during (He) leak testing are on the o-ring. Please contact us for further details.
3) this value corresponds to the maximum allowed pressure difference for the assembled socket. 4) for chrome plated product (« C » material code).
YHG Fixed plug, nut fixing, non-latching, key (G) or keys (A…M)
Reference
L maxi
Model Series A B
øA
M
e
øB
S3
E maxi
S1
Dimensions (mm)
e
E
L M S1 S3
YHG
0B
13 12.4 M9x0.6 2.4 24.1 14.2 8.2 11
YHG
1B
16 15.8 M12x1.0 3.9 28.0 16.2 10.5 14
YHG
2B
19 19.2 M15x1.0 5.5 33.1 17.8 13.5 17
YHG
3B
22 25.0 M18x1.0 5.1 38.2 22.2 16.5 22
P9 Panel cut-out (page 157)
Note: this model does not include an O-ring behind the flange, it ensures
only IP61 protection index. Consequently, it is not vacuumtight. Watertightness (when mated) is only ensured with HHG and HCG sockets.
30
www.lemo.com
®
®
HGG Fixed socket, nut fixing, key (G) or keys (A…M and R), watertight or vacuumtight
Reference
L maxi
M
øA
e
øB
S3
E maxi
S1
Model
Series
HGG
00
HGG
0B
HGG
1B
HGG
2B
HGG
3B
HGG
4B
HGG
5B
A
B
11 10.2
13 12.4
Dimensions (mm)
e
M7x0.5
M9x0.6
18 15.8 M12x1.0
20 19.2 M15x1.0
E
L
M
S1
S3
7.0 21.5 3.0
8.2
11
8.0 31.6 4.0 13.5
17
8.0 18.0 1.5
–
7.0 26.6 4.5 10.5
25 25.0 M18x1.0 11.5 36.1 4.0 16.5
34 34.0 M25x1.0 11.0 43.1 4.0 23.5
45 40.0 M35x1.0 11.0 53.6 5.0 33.5
P9 Panel cut-out (page 157)
9
14
22
30
–
Note: the 5B series is delivered with a tapered washer and a round nut.
HNG Fixed socket, nut fixing, with earthing tag, key (G) or keys (A…M), watertight or vacuumtight
L maxi
øA
M
e
øB
S3
E maxi
S1
Reference
Model
Series
HNG
0B
A
B
Dimensions (mm)
e
13 12.4 M9x0.6
P9 Panel cut-out (page 157)
E
7
L
21.5
M
3
S1
8.2
S3
11
HHG Fixed socket, nut fixing, key (G) or keys (A…M), watertight or vacuumtight (watertight when mated)
Reference
L maxi
øA
M
e
øB
S3
E maxi
S1
Model
Series
HHG
0B
HHG
1B
HHG
2B
HHG
3B
A
B
13 12.4
Dimensions (mm)
e
M9x0.6
18 15.8 M12x1.0
22 19.2 M15x1.0
E
L
M
7.0 24.5 4.8
S1
S3
8.2 11
7.0 30.3 5.2 10.5 14
8.0 35.6 6.0 13.5 17
25 25.0 M18x1.0 11.5 41.3 7.2 16.5 22
P9 Panel cut-out (page 157)
Note: this model ensures watertightness (IP66) in the mating area when
mated with FGG or similar plug.
www.lemo.com
31
®
®
HCG Fixed socket, nut fixing, key (G) or keys (A…M), watertight or vacuumtight (watertight when mated)
(back panel mounting)
L maxi
M
øA
e1
P
Reference
Model
Series
HCG
0B
HCG
1B
HCG
2B
e
øC
øB
F maxi
E maxi
S1
A
B
C
e
Dimensions (mm)
18 18 12.0 M14x1.0
e1
E
F
L
M
M9x0.6 3.9 1.0 24.5 3.5
P
S1
7.5 12.5
20 20 14.5 M16x1.0 M12x1.0 6.2 2.0 30.3 3.5 10.0 14.5
24 24 17.5 M19x1.0 M14x1.0 6.7 1.5 35.6 3.5 11.3 17.0
P3 Panel cut-out (page 157)
Note: this model ensures watertightness (IP66) in the mating area when mated with
FGG or similar plug.
HEG Fixed socket, nut fixing, key (G) or keys (A…M), watertight or vacuumtight (back panel mounting)
L maxi
P
Reference
M
e
øB
øA
S2 S1
E maxi
Model
Series
HEG
00
HEG
0B
HEG
1B
HEG
2B
A
B
e
Dimensions (mm)
E
L
M
S1
S2
9.0
8.2
–
10
11
16
18 M12x1.0 6.5 26.6 3.5 11.0 10.5
12
20
13
M7x0.5 2.5 18.2 2.5
P
M9x0.6 5.5 21.5 2.5
20 M15x1.0 5.0 31.6 3.5
P9 Panel cut-out (page 157)
6.0
6.3
–
–
9.6 13.5 15
HMG Fixed socket with earthing tag, nut fixing, key (G) or keys (A…M), watertight or vacuumtight
(back panel mounting)
L maxi
P
M
e
øB
øA
S1
Reference
E maxi
Model
Series
HMG
00
HMG
0B
HMG
A
B
Dimensions (mm)
e
E
L
M
S1
9.0
8.2
10
11
1B
18 M12x1.0 5.5 26.6 3.5 11.0 10.5
HMG
2B1)
16
HMG
3B
24
12
20
13
M7x0.5 2.5 18.0 2.5
P
M9x0.6 5.5 21.5 2.5
20 M15x1.0 5.5 31.6 3.5
6.0
6.3
9.6 13.5
25 M18x1.0 7.5 36.1 4.5 14.0 16.5
P9 Panel cut-out (page 157)
Note: 1) the surface design of the 2B series is different.
Note: The 3B series is delivered with a conical nut and without washer.
32
www.lemo.com
®
®
Sll
Fixed coupler, nut fixing, key (G) or keys (A, B, J, K and L) at the flange end and key (G)
or keys (A, B, J, K and L) at the other end, watertight or vacuumtight
L
S1
øA
M
e
øB
S3
E maxi
Reference
Model
G
SGJ
J
J
SJG
G
K
SKA
A
L
B
SLB
A
K
SAK
B
L
SBL
Example
Plug with key G
SGJ
Plug with key J
Alignment key see page 36.
Series
SGJ
0B
SJG
0B
SGJ
1B
SJG
1B
SGJ
2B
SJG
2B
SGJ
3B
SJG
3B
SAK
3B
SBL
3B
SAK
4B
SBL
4B
SGJ
4B
SJG
4B
SGJ
5B
SJG
5B
SKA
5B
SLB
5B
SAK
5B
SBL
5B
Contacts
Type
A
B
Dimensions (mm)
e
E
L
M
S1
S3
2.0
9.0 12
female – male
14
13.8 M10x0.75
17
34
2.0
female – male
17
15.8 M12x1.00
28
39
2.5 10.5 14
male – female
male – female
female – male
male – female
female – male
male – female
female – male
female – male
female – male
female – male
female – male
male – female
female – male
male – female
male – female
male – female
female – male
female – male
P4 Panel cut-out (page 157)
14
17
20
20
25
25
25
25
34
34
34
34
45
45
45
45
45
45
13.8 M10x0.75
15.8 M12x1.00
21.5 M16x1.00
21.5 M16x1.00
27.0 M20x1.00
27.0 M20x1.00
27.0 M20x1.00
27.0 M20x1.00
34.0 M25x1.00
34.0 M25x1.00
34.0 M25x1.00
34.0 M25x1.00
40.0 M35x1.00
40.0 M35x1.00
40.0 M35x1.00
40.0 M35x1.00
40.0 M35x1.00
40.0 M35x1.00
17
28
25
25
30
30
30
30
50
50
50
50
58
58
58
58
58
58
34
39
44
44
53
53
53
53
65
65
65
65
80
80
80
80
80
80
9.0 12
2.5 10.5 14
4.0 15.0 19
4.0 15.0 19
4.0 18.5 24
4.0 18.5 24
4.0 18.5 24
4.0 18.5 24
4.0 23.5 30
4.0 23.5 30
4.0 23.5 30
4.0 23.5 30
5.0 33.5
–
5.0 33.5
–
5.0 33.5
5.0 33.5
5.0 33.5
5.0 33.5
–
–
–
–
P9 Panel cut-out 1B series (page 157)
Note: The 5B series is delivered with a round nut.
Note: for this fixed coupler, the first contact type mentioned is always the one at the flange end. On
request these couplers can be produced in other series, with other keys.
www.lemo.com
33
®
Bridge models
> 1000 cycles
Working temperature
Standard
IEC 60512-5 test 9a
maximum 90° C
Note: 1) see page 189, contact resistance after mating cycles. See page
185, mechanical endurance latching force.
Materials and Treatment
Component
Material
Polyamide
Plastic housing
Brass
Metallic parts
Brass
PEEK
Insulator
Brass
Male contact
Bronze
Female contact
Surface treat. (µm)
Cu Ni Cr Au
0.5
0.5
0.5
0.5
3
3
3
–
–
3
–
–
Part number
CFF.0B.302.PLCG
CRG.0B.302.PLEG
CFF.0B.303.PLCG
–
CRG.0B.303.PLEG
–
1.0
CFF.1B.303.PLCG
–
1.5
Note: the last letter of the part number indicates the colour of the housing.
Ex. G (standard) is grey. To obtain another colour, replace this letter by
the letter corresponding to the selected colour (see table on page 72).
Bridge plug with two non-latching plugs
Value
Contact resistance
0.3
Note: the surface treatment standards are as follows:
– Nickel: SAE AMS QQ N 290, chrome: SAE AMS 2460, gold: ISO 27874
CFF
Characteristics
CRG.0B.306.PLEG
CRG.1B.303.PLEG
CFF.1B.306.PLCG
CRG.1B.306.PLEG
Standard
< 6 mΩ
0B
0B
l
–
l
–
–
l
0B
0B
4
0.80
4
0.80
–
l
0.40
l
–
1.25
1B
l
1B
–
1B
1.05
1.05
–
l
0B
IEC 60512-2 test 2a
Rated
current (A)
Endurance1)
Value
Test voltage
(kV rms) 1) 2)
Characteristics
Electrical
Audio-Mono
Mechanical and Climatical
Audio-Stereo
Technical Characteristics
Series
®
1B
–
1.25
0.80
l
–
0.80
l
4
4
2
5
5
3
3
Note:
1) see calculation method, caution and suggested standard on page 190.
2) lowest measured value; contact to contact or contact to shell.
CRG Bridge plug with two non-latching plugs, and monitoring socket, key (G) or keys (A…M)
CFF
CRG
M maxi
L maxi
34
Model
Series
CFF-CRG
0B
CFF-CRG
1B
N
B
H
A
A
13.5
15.0
Dimensions (mm)
B
14
20
H
L
M
N
27.5 37.2 27.2 22.5
35.0 42.0 31.0 22.0
Note: in order to provide the user with a coding system, the bridge plug
housing, the double panel washers and the bend reliefs are available in
nine colours.
www.lemo.com
®
®
Threaded-latching models
FVG
Straight plug, key (G) or keys (B), cable collet
~L
Reference
øA
~M
S1
ESG
S2
Model
Series
FVG
00
A
9
Dimensions (mm)
L
M
28.5
24
S1
S2
5
8
Note: to be ordered with nut for fitting a bend relief to obtain the rating
IP 64.
Fixed socket with two round nuts, key (G) or keys (B), long threaded shell (back panel mounting)
L maxi
N
øA
3.2 mini 1)
e
øB
øC
M
Series
ESG
00
A
9
B
C
9
Dimensions (mm)
e
E
L
9.5 M7x0.5 3.2 15.5
M
2
N
13.7
Note: 1) minimum length of free thread to ensure mating.
Straight plug, keys (B), short shell for special cable crimping and for fitting a bend relief
Reference
L
øA
M
XRB
Model
P2 Panel cut-out (page 157)
E maxi
FVB
Reference
Model
Series
FVB
00
Dimensions (mm)
A
9
L
20
M
15.4
Note: part number for microphone applications: FVB.00.303.NLAE24.
After assembly the special bend relief GMF.00.018.Dl (to be ordered
separately) is to be fitted.
Elbow (90°) socket for printed circuit, keys (B), short shell with one nut, screw fixing (back panel mounting)
2.05
5.5
= =
8
1.2
Reference
L
P
3
2 x M 1.4
www.lemo.com
øA
3.2 mini 1)
e
I
M
Model
Series
XRB
00
A
Dimensions (mm)
e
10 M7x0.5
P2 Panel cut-out (page 157)
I
7
L
14
M
2.5
P
7
P18 PCB drilling pattern for contact only (page 165)
Note: 1) minimum length of free thread to ensure mating.
35
®
®
Alignment Key (B series)
Alignment Key and Polarized Keying System
B series connector model part numbers are composed of three letters. The LAST LETTER indicates the key position and
the contact type (male or female).
A
α
B
)
D
β
β (5
B
C
δ
E
F
J
γ
K
L
M
Y
Ref.
α
Front view of a socket
R
–
α
2
α
2
α
2
β
2
β
2
β
2
γ
2
γ
2
γ
2
δ
3
–
3
–
Nb of
keys
5
β
γ
δ
1
2
5
5
5
α
β
γ
δ
0°
30°
60°
–
–
–
–
45°
–
–
0B
1B
30°
30°
0°
60°
90°
155° 155°
45°
70°
80°
–
–
–
–
–
–
90°
145° 145°
110°
00
60°
135° 135°
–
–
0°
–
Series
0B
–
–
–
–
45°
70°
80°
–
–
–
1B
Ref.
G
A
B
C
D
E
F
J
K
L
M
Y
Ref.
–
–
–
–
R
Nb of
keys
Angles
00
Series
1
–
2
α
2
α
2
α
2
γ
2
β
2
α
2
γ
2
β
2
α
2
–
3
γ
3
β
Nb of
keys
Angles
G
Nb of
keys
Angles
Ref.
Angles
Front view of a socket
5
α
5
γ
5
5
β
δ
XB
2B
30°
–
0°
–
–
3B
4B
5B
30°
30°
30°
30°
60°
60°
60°
60°
0°
45°
95°
120° 120°
–
–
–
–
–
–
–
145°
70°
95°
45°
95°
120° 120°
145° 145°
–
70°
–
70°
–
112.5° 126° 112.5°
100°
–
–
–
45°
0°
Plug
Socket
male
female
0°
male
45°
male
95°
120°
145°
male
male
male
male
52.5° 52.5° 52.5° 52.5° female
2B
–
0°
Contact type
37.5° 37.5° 37.5° 37.5° female
XB
–
Series
–
–
–
102° 147.5°
Series
70°
female
–
male
–
–
3B
4B
–
–
115°
–
30°
–
–
–
–
–
Note: FTG, FGY, ENY models are not available with all the keys. Please consult pages corresponding to these models.
For Rll models see explanation on page 24 and for Sll models see explanation on page 33.
5B
female
male
female
l
female
l
female
female
female
male
male
female
female
female
male
l
l
male
male
l
male
male
Socket
20°
l
l
Plug
male
l
female
Contact type
95°
Note
l
l
l
l1)
l1)
Note
female
l
female
l
female
l
l
Note: 1) only FGY and ENY models are available.
l First choice alternative
l Special order alternative
36
www.lemo.com
®
®
K Series
K series connectors have been specifically designed for outdoor applications.They include an inner sleeve and two seals to
prevent penetration of solids or liquids into the housing formed by the plug, free socket, fixed socket or coupler. All models
(except FXl model) of this series are watertight when mated to give a protection index of IP68 as per IEC 60529 standard
(in mated condition) when correctly assembled to an appropriate cable (IP66 otherwise).
K series connectors have the same insulators as the B series and have the following main features:
– security of the Push-Pull latching system
– watertight connection (IP 68/IP 66)
– multipole types 2 to 64 contacts
– solder, crimp or print (straight or elbow) contacts
– keying system («G» key standard)
– multiple key options to avoid cross mating
for connector alignment of similar connectors
– 360° screening for full EMC shielding
– high packing density for space savings
– rugged housing for extreme working conditions.
Metal housing models (page 39)
Fixed plugs
Straight plugs
Fixed sockets
FGG
FXG
EGG
EBG
Free sockets
Free coupler
PHG
TGL*
T-plug
with sockets (90°)
FAG
FGG
ENG
EDG
EEG
EHG
PHG
Elbow plug
FGG
FPG
PHG
FTG*
Fixed sockets
FNG
FHG
EEG
EVG*
PKG
EEG
PBG
Watertight or vacuumtight models (page 47)
Fixed sockets
HGG
www.lemo.com
Fixed coupler
HEG
HMG
S••
PEG
Note: * Contact LEMO for details.
37
®
®
Part Numbering System
Plug
Free socket
F G G . 3 K . 3 1 0 . C L A C 6 5
P H G . 3 K . 3 1 0 . C L L C 6 5 Z
Variant: (page 71)
Cable ø: (page 68)
Collet type: (page 68)
Fixed socket
Coupler
E G G . 3 K . 3 1 0 . C Y M
S L G . 3 K . 3 1 0 . T L A PV
Model: (page 39)
Variant: (page 71)
Alignment key: (page 49)
Contact: (page 64)
Series: (page 39)
Insulator: (page 64)
Insert configuration: (page 57)
Housing: (page 64)
FGG.3K.310.CLAC65 = straight plug with key (G) and cable collet, 3K series, multipole type with 10 contacts, outer shell in chrome-plated
brass, PEEK insulator, male solder contacts, C type collet for 6.5 mm diameter cable.
PHG.3K.310.CLLC65Z = free socket with key (G) and cable collet, 3K series, multipole type with 10 contacts, outer shell in chrome-plated
brass, PEEK insulator, female solder contacts, C type collet for 6.5 mm diameter cable and nut for fitting a bend relief.
EGG.3K.310.CYM = fixed socket, nut fixing, with key (G), 3K series, multipole type with 10 contacts, outer shell in chrome-plated brass,
PEEK extended insulator, female crimp contacts.
SLG.3K.310.TLAPV = fixed coupler, nut fixing, keys (L) on the flange end and key (G) at the other end, 3K series, multipole type with
10 contacts, outer shell in stainless steel, PEEK insulator, male-female contacts, vacuumtight.
Part Section Showing Internal Components
Straight plug
1 outer shell
Fixed socket
1 outer shell
5
2
3
4
7
7
1
6
8
2
3
7
6
4
1
9
11
10
5
2 latch sleeve
3 inner shell
2 earthing crown
4 retaining ring
4 hexagonal nut
6 split insert carrier
6 female contact
8 male contact
3 retaining ring
5 insulator
7 o-ring
5 collet nut
7 insulator
9 earthing cone
10 collet + washer 1)
11 gasket
Note: 1) depending on models.
38
www.lemo.com
®
®
Metal housing models
Technical Characteristics
Electrical
Mechanical and Climatical
Characteristics
Endurance1)
Value
> 5000 cycles
Humidity
Temperature
Standard
IEC 60512-5 test 9a
up to 95% at 60° C
range2)
- 55° C, + 200° C
Resistance to vibrations
10-2000 Hz, 15g IEC 60512-4 test 6d
Shock resistance
100 g, 6 ms
IEC 60512-4 test 6c
Salt spray corrosion test4)
> 1000h
IEC 60512-6 test 11f
Protection index (mated)3) 5)
IP 68/IP 66
IEC 60529
Climatical category
50/175/21
IEC 60068-1
Value
Characteristics
Shielding
efficiency
Standard
at 10 MHz
> 95 dB
IEC 60169-1-3
at 1 GHz
> 80 dB
IEC 60169-1-3
Note:
the various tests have been carried out with FGG and EGG connector
pairs, with chrome-plated brass shell, PEEK insulator and silicone O-ring.
Detailed electrical characteristics, as well as materials and treatment are
presented in the chapter Technical Characteristics on page 182.
1) see page 189, contact resistance after mating cycles. See page 185,
mechanical endurance latching force.
2) minimum operating temperature is -20°C for sockets fitted with an FPM
(Viton®) O-ring.
3) IP68 achieved providing that the cable is perfectly circular and that
assembly process ensures a high integrity seal.
4) for chrome plated product (« C » material code).
5) except FXl model.
FGG Straight plug, key (G) or keys (A to F, L and R), cable collet
Reference
Dimensions (mm)
Model Series A
~L
øA
~M
S2
L
M S2
FGG
0K
11 34 23.0 8
FGG
1K
13 42 28.0 9
FGG
2K
16 52 36.0 12
FGG
3K
19 61 41.0 15
FGG
4K
25 71 50.5 19
FGG
5K
38 92 67.0 30
M1 Cable assembly (page 172)
FGG Straight plug, key (G) or keys (A to F, L and R), cable collet and oversize cable collet 1)
Dimensions (mm)
Reference
Model Series A
~L
øB
øA
~M
S2
www.lemo.com
S1
B
L
M S1 S2
FGG
1K
13 14.5 60.0 46 12 12
FGG
2K
16 17.0 68.0 52 15 15
FGG
3K
19 22.0 85.0 65 19 19
FGG
4K
25 36.0 119.5 99
30
32
M2 Cable assembly (page 173)
Note: 1) correspond to K type of collet, the fitting of oversize collets onto
this model allows them to be fitted to the cables that can be accommodated
by the next housing size up (see page 68).
39
®
®
FGG Straight plug, key (G) or keys (A to F, L and R),cable collet and nut for fitting a bend relief 1)
Reference
~L
øA
~M
S2
FNG
Series
FGG
0K
FGG
1K
FGG
2K
FGG
3K
FGG
4K
L
M
S2
11
34
23.0
16
52
36.0
12
50.5
19
13
19
25
42
60
71
28.0
40.0
7
9
15
Note: 1) to order, add a «Z» at the end of the reference.
The bend relief must be ordered separately (see page 145).
Straight plug, key (G) or keys (A to F and L), cable collet and lanyard release
Reference
~L
B
øA
N
Model
Series
FNG
2K
FNG
4K
A
16
25
Dimensions (mm)
B
22
32
L
52
71
M1 Cable assembly (page 172)
M
36.0
50.5
N
S2
230
19
160
12
Note: cable material: stainless steel with Polyamide sheath
S2
Fixed plug with round flange, key (G) or keys (A to F, L and R) and screw fixing
Reference
~L
P
M
øB
øG
øA
H
S2
40
A
M1 Cable assembly (page 172)
~M
FXG
Model
Dimensions (mm)
Model
Series
FXG
3K
FXG
4K
FXG
5K
A
B
Dimensions (mm)
G
H
L
M
P
38
22.5
3.4
20.6
61
10.0 30.0
65
42.5
4.4
38.0
100
12.5 38.5
47
28.5
P6 Panel cut-out (page 159)
3.4
27.0
71
11.0 32.0
S2
15
19
30
Note: this model does not include an O-ring behind the flange, it allows
the device on which it is fitted to reach only IP50 protection index.
It does not have a cable collet.
www.lemo.com
®
®
FAG Fixed plug, nut fixing, non-latching, key (G) or keys (A to F, L and R)
Dimensions (mm)
Reference
Model Series A B
L maxi
N
øA
M
e
øB
S3
E L M N1) S1 S3
FAG
1K
FAG
2K
25 27.0 M20x1.0 4.5 33.6 18.0 28.3 18.5 24
FAG
3K
31 34.0 M24x1.0 4.0 34.3 22.5 33.8 22.5 30
FAG
4K
37 40.5 M30x1.0 4.0 35.3 23.0 36.3 28.5 36
FAG
5K
55 54.0 M45x1.5 4.0 43.5 28.5 42.3 42.5 –
20 21.5 M16x1.0 2.3 22.6 16.0 22.5 14.5 19
P1 Panel cut-out (page 159)
S1
E maxi
e
Note: The 1K series is delivered with a locking washer.
The 5K series is delivered with a round nut.
Note: 1) maximum length with crimp contacts.
FPG Elbow (90°) plug, key (G) or keys (A to F, L and R), cable collet
~L
S1
~H
øA
~M
S3
S2
D
Dimensions (mm)
Reference
Model Series A
D
H
L
M S1 S2 S3
FPG
0K
11
7.3 25 36 25
9
8
8
FPG
1K
13
8.7 33 42 28 11
9
10
FPG
2K
16 10.2 40 51 35 14 12 13
M3 Cable assembly (page 172)
FHG Elbow (90°) plug, key (G) or keys (A to F, L and R), cable collet
~L
S1
øA
~M
Dimensions (mm)
~H
Reference
D
S3
Model Series A
S2
FHG
3K
21.0 11.5 47
60 40.0 18
15
16
FHG
4K
27.5 15.5 57
72 51.5 24
19
22
D
H
L
M S1 S2 S3
M3 Cable assembly (page 172)
www.lemo.com
41
®
®
EGG Fixed socket, nut fixing, key (G) or keys (A to F, L and R)
Reference
L maxi
N
øA
M
e
øB
S3
E maxi
Model
Series
EGG
0K
EGG
1K
EGG
2K
EGG
3K
EGG
4K
EGG
5K
A
B
e
Dimensions (mm)
18 19.2 M14x1.0
20 21.5 M16x1.0
25 27.0 M20x1.0
E
L
M
N1)
S1
6
21.7 4.0 20.1 12.5 17
9
30.7 5.0 28.6 18.5 24
9
27.0 4.5 25.1 14.5 19
31 34.0 M24x1.0 11 36.2 6.0 33.6 22.5 30
37 40.5 M30x1.0
9
40.2 6.5 38.6 28.5 36
55 54.0 M45x1.5 10 47.5 9.0 43.6 42.5
P1 Panel cut-out (page 159)
S1
S3
–
Note: The 5K series is delivered with a round nut.
Note: 1) maximum length with crimp contacts.
ENG Fixed socket, nut fixing, key (G) or keys (A to F, L and R) and earthing tag
L maxi
N
øA
M
e
øB
S3
E maxi
EEG
S1
Reference
Model
Series
ENG
3K
A
31
B
e
Dimensions (mm)
E
L
34 M24x1.0 11.3 36.2
P1 Panel cut-out (page 159)
M
6
N1)
S1
S3
N1)
P
S1
33.6 22.5 30
Note: 1) maximum length with crimp contacts.
Fixed socket, nut fixing, key (G) or keys (A to F, L and R) (back panel mounting)
Reference
L maxi
N
P
e
M
E maxi
øA
øB
S1
Model
Series
EEG
0K
EEG
1K
EEG
2K
EEG
3K
EEG
4K
A
B
e
Dimensions (mm)
E
L
M
18.0 18 M14x1.0 3.4 21.7 3.5 20.1
7.0 12.5
20.0 20 M16x1.0 6.2 27.0 3.5 25.1 10.0 14.5
25.0 25 M20x1.0 5.0 30.7 3.5 28.6 10.0 18.5
30.0 31 M24x1.0 7.5 36.2 4.5 33.6 12.0 22.5
41.5 37 M30x1.0 6.0 40.2 7.0 38.6 13.5 28.5
P1 Panel cut-out (page 159)
Note: The 3K and 4K series are delivered with a conical nut.
Note: 1) maximum length with crimp contacts.
42
www.lemo.com
®
®
EEG
Fixed socket, nut fixing, key (G) or keys (A to F and R) with straight print contacts for printed circuit
(back panel mounting)
Reference
L
N
P
S1
øA
e
øB
M
Model
Series
EEG
0K
EEG
1K
EEG
2K
EEG
3K
EEG
4K
A
B
Dimensions (mm)
e
E
M
N
P
S1
18.0 18 M14x1.0 3.4
3.5 17.6
25.0 25 M20x1.0 5.0
3.5 25.8 10.0 18.5
20.0 20 M16x1.0 6.2
30.0 31 M24x1.0 7.5
41.5 37 M30x1.0 6.0
P1 Panel cut-out (page 159)
7.0 12.5
3.5 23.8 10.0 14.5
4.5 31.3 12.0 22.5
7.0 34.3 13.5 28.5
P15 PCB drilling pattern (page 160)
E maxi
Note: The 3K and 4K series are delivered with a conical nut.
EEG
Note: this contact type is available for Ell socket models fitted with female
contact.
Length «L» depends on the number of contacts, see table page 163.
Fixed socket, nut fixing, key (G) or keys (A to F and R) with elbow (90°) contacts for printed circuit
(back panel mounting)
L
Reference
N
P
S1
øA
20 mini
e
øB
M
Model
Series
EEG
0K
EEG
1K
EEG
2K
EEG
3K
A
B
Dimensions (mm)
e
E
N
18
18 M14x1.0 3.4
3.5 19.3
25
25 M20x1.0 5.0
3.5 26.6
20
30
20 M16x1.0 6.2
31 M24x1.0 7.5
P1 Panel cut-out (page 159)
E maxi
M
P
7
S1
12.5
3.5 24.3
10 14.5
4.5 31.3
12 22.5
10 18.5
P17 PCB drilling pattern (page 164)
Note: length «L» depends on the number of contacts, see PCB drilling
pattern page 164.
2
Note: The 3K series is delivered with a conical nut.
EBG Fixed socket with square flange, key (G) or keys (A to F, L and R) and screw fixing
L
N
A
Reference
M
øB
H
øG
F
Model
Series
EBG
3K
EBG
4K
EBG
5K
A
B
F
30
3
29
23
54
45
37
Dimensions (mm)
P7 Panel cut-out (page 159)
G
H
L
M
N1)
3
3.4
23
36.2
6.0
32.6
4
4.4
44
47.5
8.0
42.1
3.4
29
40.2
6.5
36.6
Note: 1) maximum length with crimp contacts.
www.lemo.com
43
®
®
EDG Fixed socket with square flange, key (G) or keys (A to F, L and R), protruding shell and earthing tag,
screw fixing
L
N
A
M
øB
øC
H
F
øG
Reference
Model
Series
EDG
3K
A
B
29
18
P7 Panel cut-out (page 159)
C
Dimensions (mm)
F
23
3
G
3.4
H
23
L
M
N1)
36.2 22.5 32.6
Note: 1) maximum length with crimp contacts.
EHG Fixed socket, nut fixing, key (G) or keys (A to F and L), protruding shell
L maxi
N
Reference
øA
M
e
øB
S4
S 3 E maxi
S1
Model
Series
EHG
0K
EHG
1K
EHG
2K
A
B
Dimensions (mm)
e
E
L
M
N1)
S1 S3 S4
18 19.2 M14x1.0 1.5 21.7 10.5 20.1 12.5 17 15
20 21.5 M16x1.0 1.5 27.0 15.5 25.1 14.5 19 17
25 27.0 M20x1.0 1.5 30.7 17.0 27.1 18.5 24 20
P1 Panel cut-out (page 159)
Note: 1) maximum length with crimp contacts.
PHG Free socket, key (G) or keys (A to F, L and R), cable collet
Reference
øA
~L
S2
Model
Series
PHG
0K
PHG
1K
PHG
2K
PHG
3K
PHG
4K
PHG
5K
Dimensions (mm)
A
L
S2
45.0
9
13
34.0
19
54.0
12
75.5
19
15
23
29
42
65.0
95.0
8
15
30
M1 Cable assembly (page 172)
44
www.lemo.com
®
®
PHG Free socket, key (G) or keys (A to F, L and R), cable collet and oversize cable collet 1)
Dimensions (mm)
Reference
Model Series A
øB
øA
~L
B
L S1 S2
PHG
1K
15 14.5 63 12 12
PHG
2K
19 17.0 70 15 15
PHG
3K
23 22.0 89 19 19
PHG
4K
29 36.0 124 30 32
M2 Cable assembly (page 173)
S2
S1
Note: 1) correspond to K type of collet, the fitting of oversize collets onto
this model allows them to be fitted to the cables that can be accommodated
by the next housing size up (see page 68).
PHG Free socket, key (G) or keys (A to F, L and R), cable collet and nut for fitting a bend relief 1)
Reference
Dimensions (mm)
Model Series A
øA
~L
S2
L S2
PHG
0K
13 34.0 7
PHG
1K
15 45.0 9
PHG
2K
19 54.0 12
PHG
3K
23 64.0 15
PHG
4K
29 75.5 19
M1 Cable assembly (page 172)
Note: 1) to order, add a «Z» at the end of the reference.
The bend relief must be ordered separately (see page 145).
PKG Fixed socket, nut fixing, key (G) or keys (A to F, L and R), cable collet
Dimensions (mm)
Reference
Model Series A B
~L
S2
øA
M
e
øB
S3
E maxi
S1
e
E L M S1 S2 S3
PKG
0K
18 19.2 M14x1.0 9.0 35.2 4.0 12.5 8
17
PKG
1K
20 21.5 M16x1.0 9.5 46.2 4.5 14.5 9
19
PKG
2K
25 27.0 M20x1.0 9.0 54.5 5.0 18.5 12 24
PKG
3K
31 34.0 M24x1.0 11.5 65.7 6.0 22.5 15 30
PKG
4K
37 40.5 M30x1.0 9.0 75.5 6.5 28.5 19 36
PKG
5K
55 54.0 M45x1.5 15.0 98.0 9.0 42.5 30
–
P1 Panel cut-out (page 159)
M1 Cable assembly (page 172)
Note: the 5K series is delivered with a round nut.
www.lemo.com
45
®
®
PBG Fixed socket, key (G) with square flange, cable collet and screw fixing
Reference
~L
A
M
øB
øC
H
øG
PEG
S2
Model
Series
PBG
3K
A
29
B
19
P7 Panel cut-out (page 159)
C
23
Dimensions (mm)
F
G
3
3.4
H
23
L
65
M
S2
S1
S2
22.5 15
M1 Cable assembly (page 172)
F
Fixed socket, nut fixing, key (G) or keys (A to F, L and R), cable collet (back panel mounting)
Reference
~L
P
S2
E maxi
øA
M
e
øB
S1
Model
Series
PEG
0K
PEG
1K
PEG
2K
PEG
3K
A
B
e
Dimensions (mm)
E
L
M
P
18
18 M14x1.0 5.0
34
3.5
8.5 12.5
25
25 M20x1.0 4.0
54
3.5
7.5 18.5 12
20
30
20 M16x1.0 6.5
31 M24x1.0 7.5
P1 Panel cut-out (page 159)
45
65
3.5 10.0 14.5
8
9
4.5 12.0 22.5 15
M1 Cable assembly (page 172)
Note: the 3K series is delivered with a conical nut.
46
www.lemo.com
®
®
Watertight or vacuumtight models
These socket and coupler models allow the device on which they are fitted to reach a protection index of IP68 as per IEC
60529. They are fully compatible with plugs of the same series and are widely used for portable radios, military, laboratory
equipment, aviation, etc.
These models are identified by a letter «P» at the end of the reference.
Most of these models are also available in a vacuumtight version. Such models are identified by an additional letter «V» at
the end of the part number (certificate on request).
Epoxy resin is used to seal these models.
Technical Characteristics
Mechanical and Climatical
Characteristics
Endurance1)
Value
> 5000 cycles
Humidity
Characteristics
IEC 60512-5 test 9a
up to 95% at 60° C
Temperature range
Salt spray corrosion
Climatical category
Leakage rate
Standard
(He)2)
0K-1K
- 20° C/+ 100° C
2K to 5K
- 20° C/+ 80° C
test4)
Maximum operating
pressure3)
Value
Standard
0K
60 bar
IEC 60512-7 test 14d
1K
60 bar
IEC 60512-7 test 14d
2K
40 bar
IEC 60512-7 test 14d
3K
30 bar
IEC 60512-7 test 14d
> 1000h
IEC 60512-6 test 11f
4K
15 bar
IEC 60512-7 test 14d
20/80/21
IEC 60068-1
5K
5 bar
IEC 60512-7 test 14d
<
10-7
mbar.l.s-1
IEC 60512-7 test 14b
Note: 1) see page 189, contact resistance after mating cycles. See page 185, mechanical endurance latching force.
2) only for vacuumtight models. Residual traces of grease used during (He) leak testing are on the o-ring. Please contact us for further details.
3) this value corresponds to the maximum allowed pressure difference for the assembled socket. 4) for chrome plated product (« C » material code).
HGG Fixed socket, nut fixing, key (G) or keys (A to F and L), watertight or vacuumtight
Reference
Dimensions (mm)
Model Series A B
L maxi
øA
M
e
øB
S3
E maxi
S1
e
E
L M S1 S3
HGG
0K
18 19.2 M14x1.0 5.5 23.0 4.0 12.5 17
HGG
1K
20 21.5 M16x1.0 9.0 30.0 4.5 14.5 19
HGG
2K
25 27.0 M20x1.0 13.0 33.7 5.0 18.5 24
HGG
3K
31 34.0 M24x1.0 16.0 41.7 6.0 22.5 30
HGG
4K
37 40.5 M30x1.0 14.0 49.2 6.5 28.5 36
HGG
5K
55 54.0 M45x1.5 10.0 55.7 9.0 42.5 –
P1 Panel cut-out (page 159)
Note: the 5K series is delivered with a round nut.
HEG Fixed socket, nut fixing, key (G) or keys (A to F and L), watertight or vacuumtight (back panel mounting)
L maxi
P
S1
M
e
E maxi
øA
øB
Reference
Dimensions (mm)
Model Series A B
e
E
L M P S1
HEG
0K
18 18 M14x1.0 3.4 23.0 3.5 7 12.5
HEG
1K
20 20 M16x1.0 6.2 30.0 3.5 10 14.5
HEG
2K
25 25 M20x1.0 5.0 33.7 3.5 10 18.5
P1 Panel cut-out (page 159)
www.lemo.com
47
®
®
HMG Fixed socket with earthing tag, nut fixing, key (G) or keys (A to F and L),
watertight or vacuumtight (back panel mounting)
L maxi
P
S1
e
øA
øB
M
E maxi
Reference
Model
Series
HMG
1K
HMG
2K
A
20
25
Dimensions (mm)
B
e
E
L
M
P
20 M16x1.0 6.2 30.0 3.5
10 14.5
25 M20x1.0 5.0 33.7 3.5
10 18.5
P1 Panel cut-out (page 159)
Sll
S1
Fixed coupler, nut fixing, key (G) or keys (L) at the flange end, and key (G) or keys (C or L)
at the other end, watertight or vacuumtight
L
M
øA
S1
e
øB
S3
E maxi
Reference
G
L
SGL
L
G
SLG
SLC
L
C
Example
Plug with key G
SGL
Plug with key L
Alignment key see page 49.
48
Model
Series
SGL
2K
SLG
2K
SLG
3K
SLG
4K
SLC
4K
SLG
5K
SLC
5K
Contacts
Type
A
B
Dimensions (mm)
e
E
L
M
S1
S3
female – male
25
27.0 M20x1.0
25
52.4 5.0 18.5 24
male – female
31
34.0 M24x1.0
33
64.0 6.0 22.5 30
male – female
male – female
male – female
male – female
male – female
P1 Panel cut-out (page 159)
25
37
37
55
55
27.0 M20x1.0
40.5 M30x1.0
40.5 M30x1.0
54.0 M45x1.5
54.0 M45x1.5
25
48
48
58
58
52.4 5.0 18.5 24
74.0 6.5 28.5 36
74.0 6.5 28.5 36
88.0 9.0 42.5
88.0 9.0 42.5
–
–
Note: for this fixed coupler, the first contact type mentioned is always the one at the flange end.
On request, these couplers can be produced in other series, with other keys.
Note: The 5K series is delivered with a round nut.
www.lemo.com
®
®
Alignment Key (K series)
Alignment Key and Polarized Keying System
K series connector model part numbers are composed of three letters. The LAST LETTER indicates the key position and
the contact type (male or female).
Nb of
keys
G
1
–
2
α
2
α
2
β
α
β
A
δ
B
C
D
E
γ
F
L
Ref.
β
γ
δ
2
2
α
2
γ
R
β
2
γ
Nb of
keys
5
α
Front view of a socket
Angles
Ref.
Angles
Front view of a socket
5
α
5
γ
5
β
δ
Series
0K
1K
2K
3K
4K
5K
30°
30°
30°
30°
30°
30°
60°
60°
60°
60°
60°
60°
0°
45°
95°
0°
45°
95°
0°
45°
95°
0°
45°
95°
0°
45°
95°
0°
male
45°
male
95°
120° 120° 120°
120° 120°
120°
75°
75°
75°
145° 145° 145°
75°
75°
Series
0K
1K
2K
–
–
–
–
–
–
–
–
145° 145°
75°
145°
3K
4K
5K
–
115°
–
–
–
25°
–
–
–
–
95°
35°
–
–
Plug
Contact type
male
male
female
male
–
male
male
male
Note: Sll and TGL models are not available with all the keys. For Sll models see explanation on page 48.
Please consult the pages corresponding to these models.
female
l
l
l
female
l
male
Contact type
l
female
female
male
–
l
female
male
Note
female
female
male
Plug
Socket
Socket
l
l
Note
female
l
female
l
female
female
l
l
l First choice alternative
l Special order alternative
www.lemo.com
49
®
®
T Series
T series connectors have been specifically designed for outdoor applications. They include an inner sleeve and seals to
prevent penetration of solids or liquids.This series is watertight when mated to give a protection index of IP68 as per IEC
60529 standard and have the following main features:
– IP68 mated
– Same mounting hole as B sockets
– Push-Pull self-latching system
– Black-chrome plated brass and plastic outershell
– Mechanical key (FGG) with multiple keys
available
to avoid cross-mating
– Multipole types 2 to 32 contacts
– High packing density for space savings
– For cables 1.0 up to 10.5 mm
– 360° shielding for full EMC shielding
– Solder, crimp or print contacts
– Compatible with existing B sockets
Metal housing models (page 52)
Straight plug
Straight plugs
FFG
FGG
Fixed sockets
Free sockets
PHG
EGG
Elbow plug
FGG
FSG
FGG
FGG
PHG
L•G
Plastic housing models (page 56)
Straight plug
PHG
EEG
Watertight or vacuumtight models (page 55)
Fixed socket
Fixed sockets
EGG
HGG
HMG
HEG
Part Section Showing Internal Components
Straight plug
Fixed socket
1 outer shell
2 earthing crown
3 hexagonal nut
4 insulator
5 female contact
6 o-ring
7 locking washer
4
2
6
3
7
5
6
1
2
5
4
3
1
6
7
8
9
10
1 outer shell
2 latch sleeve
3 inner shell
4 insulator
5 male contact
6 split insert carrier
7 earthing cone
8 gasket
9 collet
10 collet nut
50
www.lemo.com
®
®
Part Numbering System
Plug and free socket
F G G . 1 T . 3 0 6 . C L A C 4 0 Z
Variant
Cable ø (page 70)
Model (page 52)
Collet type (page 70)
Alignment key (page 51)
Contact:
A = male solder
L = female solder
C = male crimp
M = female crimp
Series
Insert configuration (page 57)
Housing:
C = Chrome plated brass
K = Black Chrome plated brass
B = POM (black)
Insulator: PEEK
L = for solder contact
Y = for crimp contact
FGG.1T.306.CLAC40Z = Straight plug with key (G) and cable collet for bend relief, 1T series, multipole type with 6 contacts, outer shell
in chrome-plated brass, PEEK insulator, male solder contacts, C type collet for 4.0 mm diameter cable and nut for fitting a bend relief.
Fixed socket
E G G . 1 T . 3 0 6 . C L L
Variant
Model (page 54)
Contact:
L = female solder
A = male solder
M = female crimp
C = male crimp
N = female print
D = male print
V = female elbow print
Alignment key (page 51)
Series
Insert configuration (page 57)
Housing:
C = Chrome plated brass
K = Black Chrome plated brass
B = POM
Insulator: PEEK
L = for solder or print contact
Y = for crimp contact
EGG.1T.306.CLL = fixed socket, nut fixing, with key (G), 1T series, multipole type with 6 contacts, outer shell in chrome-plated brass,
PEEK insulator, female solder contacts.
Key
Alignment Key
G
D
A
J
L
J 1)
Contact type
Plug
Socket
G
male
female
A
male
female
D
male
female
L
female
male
J
female
male
Note: 1) for 2T and 3T series.
www.lemo.com
51
®
®
Metal housing models
Technical Characteristics
Electrical
Mechanical and Climatical
Characteristics
Endurance 1)
Value
> 3000 cycles
Humidity
Temperature
Standard
IEC 60512-5 test 9a
Shielding
efficiency
up to 95% at 60° C
range 2)
- 55° C, + 200° C / (-20°C, +80°C)
Resistance to vibrations
10-2000 Hz, 15g IEC 60512-4 test 6d
Shock resistance
100 g, 6 ms
IEC 60512-4 test 6c
Salt spray corrosion test 6)
> 1000h
IEC 60512-6 test 11f
Protection index (mated) 3)
IP 68/IP 66
IEC 60529
Latching retention force 4) 5)
Climatical category
Value
Characteristics
Standard
at 10 MHz
> 75 dB
IEC 60169-1-3
at 1 GHz
> 40 dB
IEC 60169-1-3
Note:
the various tests have been carried out with FGG and EGG connector
pairs, with chrome-plated brass shell and PEEK insulator.
Detailed electrical characteristics, as well as materials and treatment are
presented in the chapter Technical Characteristics on page 182.
From 85 N up to 300 N
50/175/21
IEC 60068-1
Note:
1) see page 189, contact resistance after mating cycles. See page 185, mechanical endurance latching force.
2) operating temperature is -20°C, +80°C for watertight or vacuumtight models fitted with an FPM (Viton®) o-ring and Epoxy.
3) IP68 achieved providing that the cable is perfectly circular and that assembly process ensures a high integrity seal.
4) average value.
5) depending of the size.
6) for chrome plated product (« C » material code).
FGG Straight plug, cable collet
Reference
Dimensions (mm)
Model Series A
øA
~M
~L
S2
S1
L
Cable ø
M S1 S2
min. max.
FGG
TT
7.0 33.2 25.2 5.5 5
2.4
3.0
FGG
0T
9.5 39.0 29.0 7.5 7
1.0
4.5
FGG
1T
12.0 46.0 35.0 11.0
1.3
6.5
FGG
2T
15.0 55.0 43.0 14.0 12 1.3
8.5
FGG
3T
18.8 64.0 49.0 16.0 14 2.6 10.5
9
M1 Cable assembly (page 174)
FGG Straight plug, cable collet and oversize cable collet 1)
Reference
Dimensions (mm)
Cable ø
Model Series A B L M S1 S2 S3 min. max.
~L
øB
øA
~M
S3
S2
FGG
0T
FGG
1T
12.0 13.9 60.2 49.1 11.0 13
12 6.6 8.5
FGG
2T
15.0 16.5 69.1 57.0 14.0 15
14 8.6 10.5
FGG
3T
18.8 23.0 87.7 72.7 16.0 20
20 10.6 15.0
9.5 10.9 50.7 40.9 8.5 10
9 4.6 6.5
S1
M2 Cable assembly (page 174)
Note: 1) correspond to K type of collet, the fitting of oversize collets onto
this model allows them to be fitted to the cables that can be accommodated
by the next housing size up (see page 70).
52
www.lemo.com
®
®
FGG Straight plug, cable collet and nut for fitting a bend relief 1)
Dimensions (mm)
Reference
Model Series A
øA
~M
~L
S2
S1
L
Cable ø
M S1 S2
min. max.
FGG
TT
7.0 32.7 24.7 5.5 6
2.4
3.0
FGG
0T
9.5 38.0 28.0 7.5 7
1.0
4.5
FGG
1T
12.0 45.0 34.0 11.0
1.3
6.5
FGG
2T
15.0 54.0 42.0 14.0 12 1.3
8.5
FGG
3T
18.8 62.0 47.0 16.0 15 2.6 10.5
9
M1 Cable assembly (page 174)
Note: 1) to order, add a «Z» at the end of the reference.
The bend relief must be ordered separately (see page 145).
FFG Straight plug, non latching, cable collet
Reference
Dimensions (mm)
Model Series A
~L
øA
~M
S2
S1
L
Cable ø
M S1 S2
min. max.
FFG
TT
7.0 33.2 25.2 5.5 5
2.4
3.0
FFG
0T
9.5 39.0 29.0 8.0 7
1.0
4.5
FFG
1T
12.0 46.0 35.0 10.0
1.3
6.5
FFG
2T
15.0 55.0 43.0 13.0 12 1.3
8.5
FFG
3T
18.8 64.0 49.0 16.0 14 2.6 10.5
9
M1 Cable assembly (page 174)
FSG Adjustable right angle plug
L
Reference
~H
øA
M
S2
S1
Dimensions (mm)
Model Series A H
Cable ø
L M S1 S2 min. max.
FSG
TT
8 20.0 28.5 20.5 5
7.5 2.4 3.0
FSG
0T
10 23.0 36.0 26.0 7
9.5 1.0 4.5
FSG
1T
13 30.0 43.5 32.5 9 12.0 1.3 6.5
FSG
2T
17 37.5 54.0 42.0 12 16.0 1.3 8.5
PHG Free socket, cable collet
Reference
Dimensions (mm)
Model Series A
øA
~L
S2
S1
L
Cable ø
S1 S2
min. max.
PHG
TT 7.0 32.0 5.5 5
2.4
3.0
PHG
0T
9.5 38.0 8.0 7
1.0
4.5
PHG
1T
12.0 43.5 10.0
1.3
6.5
PHG
2T
15.0 52.0 13.0 12 1.3
8.5
PHG
3T
18.8 61.5 16.0 14 2.6 10.5
9
M1 Cable assembly (page 174)
www.lemo.com
53
®
®
PHG Free socket, cable collet and oversize cable collet 1)
Reference
Dimensions (mm)
Cable ø
Model Series A B L S1 S2 S3 min. max.
øB
øA
~L
S3
S2
S1
PHG
0T
PHG
1T
12.0 13.9 58.2 10
13
12 6.6 8.5
PHG
2T
15.0 16.5 66.6 13
15
14 8.6 10.5
PHG
3T
18.8 23.0 85.5 16
20
20 10.6 15.0
9.5 10.9 49.7 8
10
9
4.6 6.5
M2 Cable assembly (page 174)
Note: 1) correspond to K type of collet, the fitting of oversize collets onto
this model allows them to be fitted to the cables that can be accommodated
by the next housing size up (see page 70).
PHG Free socket, cable collet and nut for fitting a bend relief 1)
Reference
Dimensions (mm)
Model Series A
øA
~L
S2
S1
L
Cable ø
S1 S2
min. max.
PHG
TT 7.0 31.5 5.5 6
2.4
3.0
PHG
0T
9.5 37.0 8.0 7
1.0
4.5
PHG
1T
12.0 42.5 10.0
1.3
6.5
PHG
2T
15.0 51.0 13.0 12 1.3
8.5
PHG
3T
18.8 60.0 16.0 15 2.6 10.5
9
M1 Cable assembly (page 174)
Note: 1) to order, add a «Z» at the end of the reference.
The bend relief must be ordered separately (see page 145).
EGG Fixed socket, nut fixing
Dimensions (mm)
Reference
Model Series A B
L maxi
N
M
øB
e
øA
S2
S1
E maxi
e
E L M N1) S1 S2
EGG
TT
10.0 10.2 M7x0.5 5.5 16.0 1.2 13.5 6.3 9
EGG
0T
12.0 12.5 M9x0.6 6.0 21.0 1.5 19.1 8.2 11
EGG
1T
15.5 16.0 M12x1.0 6.0 23.0 1.8 21.5 10.5 14
EGG
2T
18.5 19.6 M15x1.0 7.5 26.5 1.8 24.6 13.5 17
EGG
3T
23.5 25.1 M18x1.0 9.6 30.1 2.5 25.0 16.5 22
P1 Panel cut-out (page 157)
Note: 1) maximum length with crimp contacts.
EEG Fixed socket, nut fixing (back panel mounting)
Dimensions (mm)
Reference
Model Series A B
L maxi
e
øB
øA
N
S1
E maxi
P
e
E L N1)
P
S1
EEG
TT
10.0 10.0 M7x0.5 4.5 16.0 13.5 7
6.3
EEG
0T
12.0 12.0 M9x0.6 6.5 21.0 19.1 9
8.2
EEG
1T
15.5 16.0 M12x1.0 6.5 23.0 21.5 10 10.5
EEG
2T
18.5 20.0 M15x1.0 7.5 26.5 24.6 11 13.5
EEG
3T
23.5 24.0 M18x1.0 7.5 30.1 25.0 12 16.5
P1 Panel cut-out (page 157)
Note: 1) maximum length with crimp contacts.
54
www.lemo.com
®
®
L lG Fixed socket, nut fixing, key (G) or keys (A…L)
Reference
Dimensions (mm)
Model Series A B
V+
(3.3-3.6 Vdc)
Red (GND)
Green (GND)
Blue (GND)
N
M
19 18.2 M13x0.75 4.0 18.5 5 16.0 11.5 16
LlG 1T
21 19.2 M15x1.00 5.8 21.0 5 18.5 13.5 17
LlG 2T
25 27.0 M20x1.00 6.5 24.1 5 21.5 18.5 24
S1
ø A + 0.1
0
øB
e
øA
L mini
E maxi
E L M N S1 S2
Note: Only available with solder or crimp contacts.
LEG model is with LED flange, LNG model is with narrow LED flange and
LMG model is with single standby LED flange.
L
S2
LlG 0T
e
AWG 28 / AWG 30
B + 0.1
0
Series
Dim. (mm)
A B L
0T
13.1 11.6 24
1T
15.1 13.6 26
2T
20.1 18.6 29
Watertight or vacuumtight models
These models are identified by a letter «P» at the end of the reference. Most of these models are also available in a vacuumtight version. Such models are identified by an additional letter «V» at the end of the part number (certificate on request).
Epoxy resin is used to seal these models. The temperature range is -20°C / +80°C.
Part Number Example
HGG.0T.305.CLLP (5 contacts, resin potted) / HGG.0T.305.CLLPV (5 contacts, resin potted and vacuumtight tested)
Mechanical and Climatical Characteristics
Characteristics
Endurance 1)
Value
> 3000 cycles
Humidity
Temperature
Standard
IEC 60512-5 test 9a
up to 95% at 60° C
range 2)
-20°C, +80°C
Resistance to vibrations
10-2000 Hz, 15g IEC 60512-4 test 6d
Shock resistance
100 g, 6 ms
IEC 60512-4 test 6c
> 1000h
IEC 60512-6 test 11f
IP 68/IP 66
IEC 60529
Salt spray corrosion
test 6)
Protection index (mated) 3)
Latching retention force 4) 5)
Characteristics
From 85 N up to 300 N
Climatical category
50/175/21
Leakage rate (He)
< 10-7 mbar.l.s-1 IEC 60512-7 test 14b
IEC 60068-1
Maximum operating
pressure7)
Value
Standard
TT
60 bar
IEC 60512-7 test 14d
0T
60 bar
IEC 60512-7 test 14d
1T
60 bar
IEC 60512-7 test 14d
2T
40 bar
IEC 60512-7 test 14d
Note:
1) see page 189, contact resistance after mating cycles. See page 185,
mechanical endurance latching force.
2) operating temperature is -20°C, +80°C for watertight or vacuumtight
models fitted with an FPM (Viton®) o-ring and Epoxy.
3) IP68 achieved providing that the cable is perfectly circular and that
assembly process ensures a high integrity seal.
4) average value.
5) depending of the size.
6) for chrome plated product (« C » material code).
7) this value corresponds to the maximum allowed pressure difference for
the assembled socket.
HGG Fixed socket, nut fixing, watertight or vacuumtight
Reference
L maxi
Model Series A B
M
øB
e
øA
S2
N
E maxi
Dimensions (mm)
S1
e
E L M N1) S1 S2
HGG
TT
10.0 10.2 M7x0.5 5.5 18.0 1.2 15.0 6.3 9
HGG
0T
12.0 12.5 M9x0.6 6.5 22.0 1.5 18.5 8.2 11
HGG
1T
15.5 16.0 M12x1.0 6.0 26.0 1.8 21.5 10.5 14
HGG
2T
18.5 19.6 M15x1.0 8.0 30.5 1.8 25.0 13.5 17
P9 Panel cut-out (page 157)
55
®
®
HEG Fixed socket, nut fixing, watertight or vacuumtight (back panel mounting)
Dimensions (mm)
Reference
L maxi
Model Series A B
e
øB
øA
N
S1
E maxi
P
e
E L
N
P
S1
HEG
TT
10.0 10.0 M7x0.5 4.5 18.0 15.0 7
6.3
HEG
0T
12.0 12.0 M9x0.6 6.5 22.0 18.5 9
8.2
HEG
1T
15.5 16.0 M12x1.0 6.5 26.0 21.5 10 10.5
HEG
2T
18.5 20.0 M15x1.0 7.5 30.5 25.0 11 13.5
P9 Panel cut-out (page 157)
HMG Fixed socket with earthing tag, nut fixing, watertight or vacuumtight (back panel mounting)
Dimensions (mm)
Reference
L maxi
Model Series A B
e
øB
øA
N
S1
E maxi
P
e
E L
N
P
S1
HMG
TT
10.0 10.0 M7x0.5 4.5 18.0 15.0 7
6.3
HMG
0T
12.0 12.0 M9x0.6 6.5 22.0 18.5 9
8.2
HMG
1T
15.5 16.0 M12x1.0 6.5 26.0 21.5 10 10.5
HMG
2T
18.5 20.0 M15x1.0 7.5 30.5 25.0 11 13.5
P9 Panel cut-out (page 157)
Plastic housing models
FGG Straight plug, cable collet and nut for fitting a bend relief, POM outer shell 1)
Reference
Dimensions (mm)
Model Series A
øA
~M
~L
S2
L
Cable ø
M S2
min. max.
FGG
0T
9.7 38.5 28.5 8
FGG
1T
13.0 45.0 34.0 10 1.3 6.5
1.0 4.5
M1 Cable assembly (page 174)
Note: 1) to order, add a «Z» at the end of the reference.
The bend relief must be ordered separately (see page 145).
EGG Fixed socket, nut fixing, POM outer shell
L maxi
N
Reference
M
øB
e
øA
S2
E maxi
S1
Dimensions (mm)
Model Series A B
e
E L M N1) S1 S2
EGG
0T
12.0 12.5 M9x0.6 6.0 21.0 1.5 19.1 8.2 11
EGG
1T
15.5 16.0 M12x1.0 6.0 23.0 1.8 21.5 10.5 14
P1 Panel cut-out (page 157)
Note: 1) maximum length with crimp contacts.
56
www.lemo.com
®
®
Insert configuration (B, K and T series)
0B-0K-0T
302
1.3
3B-3K-3T
3.0
2B-2K-2T
00-TT
0B-0K-0T
303
4
0.9
2.0
1.6
0.5
0.7
1B-1K-1T
0.9
3B-3K-3T
2.0
2B-2K-2T
5B-5K
305
www.lemo.com
0.5
3B-3K-3T
2B-2K-2T
4B-4K
l First choice alternative
l Special order alternative
6.0
1.3
0B-0K-0T
5
2.0
1B-1K-1T
00-TT
304
0.9
1B-1K-1T
5B-5K
3
Note:
00-TT
1)
2)
3)
4)
1.3
3.0
4.0
0.35
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
–
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
–
l
l
–
–
–
–
–
–
20
20
16
12
8
32
26
18
14
–
28
Rated current (A)1)
32
Test voltage (kV rms)4)
Contact-shell
30
Crimp
contact
Test voltage (kV rms)1)
Contact-contact
0.5
Test voltage (kV rms)1)
Contact-contact
00-TT
max.
Series
2
min.
2
Solder (max.)
3
Crimp
Print (elbow)
Crimp contacts
Crimp
3
1
Solder
2
4
Contact ø (mm)
4
Reference
1
Solder
contact
AWG
Test voltage (kV rms)4)
Contact-shell
Contact
type
Solder contacts
Print (straight)
Multipole
1.00
0.95
1.15
1.20
18
1.50
1.35
1.70
1.45 15.03)
10
2.10
1.55
2.30
1.80
35.0
3.0
20
12
–
1.00
2.10
3.60
1.05
1.75
2.95
1.45
2.85
–
3.5
1.20 10.02)
2.70 25.03)
–
50.0
30
32
28
0.80
0.95
1.35
1.10
20
26
18
1.30
1.55
1.60
1.85
12
1.90
1.50
3.20
2.65
25.0
22
0.85
0.70
1.35
1.10
7.02)
20
18
16
30
22
22
20
16
12
10
30
32
22
18
32
32
32
26
18
14
12
–
20
14
28
1.20
2.40
0.80
0.90
1.85
0.65
1.70
1.90
1.05
1.60
8.02)
12.0
1.90 17.03)
1.05
2.0
20
1.35
1.45
1.70
1.80 10.02)
12
1.45
1.25
2.50
2.20
19.0
2.40
35.0
18
10
10
–
1.85
2.10
2.95
0.70
1.85
1.50
2.65
1.00
2.20
1.80
3.20
–
2.20 15.03)
1.20
–
30.0
1.7
see calculation method, caution and suggested standard on page 190.
rated current = 6A for socket with elbow (90°) contact for printed circuit.
rated current = 12A for socket with elbow (90°) contact for printed circuit.
test voltage (kV) contact-shell is slightly lower for K and T series (values here are for B series).
57
®
®
Multipole
5
Rated current (A)1)
Test voltage (kV rms)5)
Contact-shell
l
l
l
l
22 32 22 1.00 0.70 1.25 1.20 6.52)
1B-1K-1T 0.9
l
l
l
l
22 32 20 1.25 1.15 1.30 1.55 9.02)
2B-2K-2T 1.3
l
l
l
l
20 26 18 1.75 1.60 2.15 2.15 14.03)
3B-3K-3T 1.6
l
l
l
l
18 22 14
1.90 1.25 2.40 1.75 19.0
0B-0K-0T 0.5
l
l4)
l
l
28 32 28 0.85 0.65 1.40 1.20 2.5
1B-1K-1T 0.7
l
l
l
l
22 32 22 1.05 1.20 1.35 1.45 7.02)
l
–
–
–
30
2B-2K-2T 1.3
l
l
l
l
20 26 18 1.35 1.45 2.00 2.35 12.0
3B-3K-3T 1.6
l
l
l
l
1.60 1.15 1.90 1.80 17.0
18 22 14
2.0
l
l
l
–
2.00 1.75 2.75 2.40 24.0
16 18 12
0B-0K-0T 0.5
l
l4)
l
l
28 32 28
0.80 0.70 1.40 1.20 2.5
1B-1K-1T 0.7
l
l
l
l
22 32 22 0.95 1.05 1.45 1.45 7.02)
2B-2K-2T 1.3
l
l
l
l
20 26 18
1.75 1.60 1.95 2.15 11.0
3B-3K-3T 1.6
l
l
l
l
1.70 1.25 2.00 2.05 15.0
18 22 14
2.0
l
l
l
–
2.00 1.80 1.50 1.35 20.0
16 18 12
1B-1K-1T 0.7
l
l
l
l
22 32 22 0.95 1.15 1.30 1.30 5.0
2B-2K-2T 0.9
l
l
l
l
22 32 20 1.50 1.25 1.95 1.95 10.02)
3B-3K-3T 1.3
l
l
l
l
20 26 18 1.65 1.15 1.85 1.75 13.0
max.
0B-0K-0T 0.7
min.
Solder (max.)
Reference
Crimp contacts
Print (elbow)
2
Print (straight)
1
3
Crimp
4
3
Solder
4
2
Series
1
Contact ø (mm)
Crimp
Crimp
contact
Test voltage (kV rms)1)
Contact-contact
Solder
contact
AWG
Test voltage (kV rms)5)
Contact-shell
Contact
type
Test voltage (kV rms)1)
Contact-contact
Solder contacts
305
6
306
00-TT
6
0.35
–
–
0.60 0.75
–
– 1.5
306
4B-4K
7
307
4B-4K
8
308
8
308
l First choice alternative
l Special order alternative
58
Note: 1) see calculation method, caution and suggested standard on page 190.
2) rated current = 6A for socket with elbow (90°) contact for printed circuit.
3) rated current = 12A for socket with elbow (90°) contact for printed circuit.
4) available only for connectors fitted with male contacts.
5) test voltage (kV) contact-shell is slightly lower for K and T series (values here are for B series).
www.lemo.com
®
®
Multipole
Rated current (A)1)
Test voltage (kV rms)4)
Contact-shell
Test voltage (kV rms)1)
Contact-contact
l
l
28 32 28 0.60 0.50 1.00 0.85 2.0
l
l
–
6.0
20 26 18
1.35 1.05 1.10 1.05
16 18 12 15.0
max.
l3)
min.
Print (elbow)
l
Solder (max.)
Print (straight)
1
2
Crimp
Crimp contacts
4
3
Crimp
contact
Solder
3
Contact ø (mm)
4
2
Reference
1
Series
Crimp
Test voltage (kV rms)4)
Contact-shell
Solder
contact
AWG
Test voltage (kV rms)1)
Contact-contact
Contact
type
Solder contacts
9
309
0B-0K-0T 0.5
309
8x1.3
3B-3K-3T
1x2.0 l
9
10
310
1B-1K-1T 0.5
l
l3)
l
l
28 32 28
0.90 1.50 1.20 1.80 2.5
2B-2K-2T 0.9
l
l
l
l
22 32 20
3B-3K-3T 1.3
l
l
l
l
20 26 18
1.25 0.90 1.50 1.80 12.0
1.45 1.30 1.80 2.10 8.02)
4B-4K
1.6
l
l
l
–
18 22 14
1.85 1.30 1.90 1.95 17.0
5B-5K
3.0
l
l
l
–
12 14 10
2.35 2.30 2.65 3.20 20.0
0B-0K-0T 0.35
l
–
l
–
30
0.80 1.00
–
–
1.5
0.7
l
–
l
–
22 32 22 1.35 1.65
–
–
5.0
2B-2K-2T 0.7
l
l
l
l
22 32 22 1.25 1.35 1.65 2.00 7.02)
3B-3K-3T
0.9
l
l
l
l
22 32 20
4B-4K
1.3
l
l
l
–
20 26 18
1.45 1.60 1.90 1.85 12.0
12
312
–
–
12
312
12
312
l First choice alternative
Special order alternative
www.lemo.com
XB
1.45 1.00 1.65 1.85 9.0
Note: 1) see calculation method, caution and suggested standard on page 190.
2) rated current = 6A for socket with elbow (90°) contact for printed circuit.
3) available only for connectors fitted with male contacts.
4) test voltage (kV) contact-shell is slightly lower for K and T series (values here are for B series).
59
®
®
Multipole
314
Rated current (A)1)
Test voltage (kV rms)4)
Contact-shell
Test voltage (kV rms)1)
Contact-contact
l3)
l
l
28 32 28 0.80 1.20 0.95 1.60 2.0
2B-2K-2T
l
l
l
l
22 32 22
l
l
l
l
22 32 20 1.20 1.20 1.80 1.65 9.02)
2.0
l
l
l
–
16 18 12
2.10 2.00 2.85 2.95 18.0
1B-1K-1T 0.5
l
l3)
l
l
28 32 28 0.80 1.25 0.95 1.60 1.5
2B-2K-2T 0.7
l
l
l
l
22 32 22 0.95 1.25 1.55 1.75 6.0
3B-3K-3T
0.9
l
l
l
l
22 32 20 1.20 0.85 1.80 1.50 8.0
4B-4K
0.9
l
l
l
–
22 32 20
5B-5K
2.0
l
l
l
–
16 18 12
1.85 1.95 2.45 3.05 12.0
2B-2K-2T 0.7
l
l
l
l
22 32 22 0.85 1.20 1.45 2.10 5.5
3B-3K-3T
l
l
l
l
22 32 20
0.7
3B-3K-3T 0.9
5B-5K
max.
l
min.
1B-1K-1T 0.5
Solder (max.)
Print (elbow)
14
Print (straight)
1
2
Crimp
Crimp contacts
4
3
Crimp
contact
Solder
3
Series
4
2
Reference
1
Contact ø (mm)
Crimp
Test voltage (kV rms)4)
Contact-shell
Solder
contact
AWG
Test voltage (kV rms)1)
Contact-contact
Contact
type
Solder contacts
1.15 1.35 1.55 1.55 6.52)
16
316
16
316
18
318
0.9
1.35 1.50 2.30 2.10 10.0
1.20 1.05 1.85 1.60 7.0
19
319
2B-2K-2T 0.7
l
l
l
l
22 32 22 0.95 1.25 1.55 1.65 5.0
320
3B-3K-3T 0.7
l
l
l
l
22 32 22 1.00 0.90 1.35 1.55 6.0
20
l First choice alternative
Special order alternative
60
Note: 1) see calculation method, caution and suggested standard on page 190.
2) rated current = 6A for socket with elbow (90°) contact for printed circuit.
3) available only for connectors fitted with male contacts.
4) test voltage (kV) contact-shell is slightly lower for K and T series (values here are for B series).
www.lemo.com
®
®
Multipole
320
Rated current (A)1)
Test voltage (kV rms)2)
Contact-shell
Test voltage (kV rms)1)
Contact-contact
l
l
l
–
22 32 20 1.35 1.00 1.05 0.95 8.0
5B-5K
1.6
l
l
l
–
18 22 14
XB
0.5
l
–
l
–
28
3B-3K-3T 0.7
l
l
l
l
22 32 22 1.00 0.90 1.70 1.45 5.5
3B-3K-3T 0.7
l
l
l
l
22 32 22 0.95 0.80 1.35 1.35 4.0
l
l
l
–
22 32 20
2B-2K-2T 0.5
l
–
l
l
28
3B-3K-3T 0.7
l
l
l
l
22 32 22
3B-3K-3T 0.7
l
l
l
l
22 32 22 0.80 0.70 1.35 1.20 3.5
max.
0.9
min.
4B-4K
Solder (max.)
Print (elbow)
20
Print (straight)
1
2
Crimp
Crimp contacts
4
3
Solder
3
Contact ø (mm)
4
2
Reference
1
Crimp
contact
Series
Crimp
Test voltage (kV rms)2)
Contact-shell
Solder
contact
AWG
Test voltage (kV rms)1)
Contact-contact
Contact
type
Solder contacts
1.90 1.70 2.20 2.40 10.0
22
322
–
–
0.50 0.90
–
–
1.5
22
322
24
324
26
326
30
330
l First choice alternative
Special order alternative
www.lemo.com
4B-4K
0.9
–
–
1.20 1.45 1.80 2.05 7.0
0.95 1.30
–
– 2.0
0.95 0.70 1.50 1.30 4.0
4B-4K
0.9
l
l
l
–
22 32 20
0.95 0.85 1.75 1.45 5.0
5B-5K
1.3
l
l
l
–
20 26 18 1.45 1.60 2.05 2.45 8.0
Note: 1) see calculation method, caution and suggested standard on page 190.
2) test voltage (kV) contact-shell is slightly lower for K and T series (values here are for B series).
61
®
®
Multipole
Print (straight)
Print (elbow)
Solder (max.)
min.
max.
Test voltage (kV rms)1)
Contact-contact
Test voltage (kV rms)2)
Contact-shell
Rated current (A)1)
1
2
Crimp
Crimp contacts
4
3
Crimp
contact
Solder
3
Contact ø (mm)
4
2
Reference
1
Series
Crimp
Test voltage (kV rms)2)
Contact-shell
Solder
contact
AWG
Test voltage (kV rms)1)
Contact-contact
Contact
type
Solder contacts
l
–
l
l
28
–
–
0.80 1.20
–
–
1.5
–
–
3.0
32
332
2B-2K-2T 0.5
32
3B-3K
0.7
l
l
l
l
22 32 22 0.75 0.70
4B-4K
0.7
l
l
l
–
22 32 22 0.90 0.90 1.30 1.30 2.0
5B-5K
1.3
l
l
l
–
20 26 18
348
4B-4K
0.7
l
l
l
–
22 32 22 0.70 0.70 1.00 1.00 1.5
348
5B-5K
1.3
l
l
l
–
20 26 18 1.20 1.10 2.00 1.55 6.0
350
5B-5K
0.9
l
l
l
–
22 32 20 1.30 1.60 1.20 1.45 6.0
332
40
340
1.30 1.45 2.00 1.95 7.0
48
48
50
l First choice alternative
Special order alternative
62
Note: 1) see calculation method, caution and suggested standard on page 190.
2) test voltage (kV) contact-shell is slightly lower for K and T series (values here are for B series).
www.lemo.com
®
®
64
l First choice alternative
l Special order alternative
www.lemo.com
Rated current (A)1)
Test voltage (kV rms)2)
Contact-shell
Crimp
contact
Test voltage (kV rms)1)
Contact-contact
min.
max.
Solder (max.)
Test voltage (kV rms)1)
Contact-contact
Crimp
Print (elbow)
54
Crimp
1
2
Solder
Crimp contacts
4
3
Contact ø (mm)
3
Series
4
2
Reference
1
Solder
contact
AWG
Test voltage (kV rms)2)
Contact-shell
Contact
type
Solder contacts
Print (straight)
Multipole
354
5B-5K
0.9
l
l
l
–
22
32
20
1.15
1.55
2.00
2.10
5.0
364
5B-5K
0.9
l
l
l
–
22
32
20
1.30
1.55
1.35
1.85
3.0
Note:
1)
2)
see calculation method, caution and suggested standard on page 190.
test voltage (kV) contact-shell is slightly lower for K and T series (values here are for B series).
63
®
®
Housings (B, K and T series)
Ref.
C
N
K
S
T
U
L
X
G
P
R
H
P
Outer shell and collet nut
Material
Surf. treatment
Brass
nickel
Brass
Brass
Stainless steel
Stainless steel
Latch sleeve + earthing crown
Material
chrome
black chrome
–
brass/bronze
nickel
brass/bronze
nickel 2)
stainless steel
–
brass/bronze
stainless steel
Aluminium alloy
anodized
brass/bronze
PEEK (natural)
–
brass/bronze
–
brass/bronze
–
Aluminium alloy nickel anthracite brass/bronze
PSU
–
PPS/brass
–/nickel
PPSU
PA.6
nickel 2)
brass/bronze
3)
–
Stainless steel
Surf. treatment
–
brass/bronze
brass/bronze
brass/bronze
Other metallic components
nickel
–
brass
nickel
l
nickel
l
nickel
brass
2)
l
nickel
brass
l
brass
nickel
brass
nickel
1)
nickel
2)
brass
nickel
Only for FGG and ENG (B series)
nickel
2)
brass
nickel 2)
stainless steel
nickel 2)
nickel
nickel
nickel
2)
2)
2)
Note
Surf. treatment
brass
2)
Remarks
Material
–
brass
nickel
l
l
l
brass
nickel
Only for FGY and ENY (B series)
brass
nickel
Only for elbow sockets (B series)
brass
nickel
Note: detailed characteristics of these materials and treatments are presented on page 182.
1) see «variant» for the colour.
2) in the K series, the latch sleeve is chrome-plated.
3) surface not conductive use socket with earthing tag (ENl and HMl model) to carry shield.
nickel
Only for FGY and ENY (B series)
l
l
1)
l
1)
Only for CRF and CRG bridge plug
l
1)
l
l
l First choice alternative
l Special order alternative
Insulators (B, K and T series)
Ref.
Y
L
Material
PEEK
PEEK
Contact type
Crimp
Solder or print
Remarks
extended design, with contacts that recess into insulator
Note: detailed characteristics of these materials are presented on page 187.
Note
l
l
Contacts (B, K and T series)
Soldering characteristics
– no need to order specific tools, a simple soldering iron
is sufficient
– ideal for very small and fragile conductors
– contacts with solder cups to allow the solder to flow
Note: see page 188 for more information.
64
Crimping characteristics
–
–
–
–
practical, quick contact fixing outside the insulator
possible use at high temperature
need to order specific tools
no risk of heating the insulator during the conductorcontact fixing
– high tensile strength
– totally lead-free solution
www.lemo.com
®
®
Conductor
Stranded
AWG
Section (mm2)
Fr 1)
(N) Notes
Contacts reference for couplers Rll, Sll and TGL
Contact type
Ref.
A
Remarks
Male - Female
contact configuration is explained on page 24, 33, 48
Female - Female
contact configuration is explained on page 24
Female - Male
L
M
contact configuration is explained on page 24, 33, 48
Contacts reference for plugs, free or fixed sockets
Reference
Contact type
Male Female
Solder
øA
0.35
A
L
0.7
0.80
–
1.3
1.6
3.0
4.0
øA
6.0
fig. 1
øA
øA
øC
øC
fig. 2
øA
øC
øC
C
M
C
M
B
P
C
M
B
P
G
U
C
M
B
P
G
U
C
M
B
P
C
M
B
P
C
M
C
M
–
–
2.0
Crimp
0.40
0.402)
0.9
øC
øC
Form
(mm) per fig.
0.52)
0.5
øC
øA
øA
(mm)
Contact
0.456)
–
Solid
AWG Section
max.
max.
(mm2)
28
0.09
28
0.09
28
22
0.805)
–
225)
1.40
–
16
1.00
1.80
2.70
3.70
5.20
–
–
–
–
–
0.09
0.34
max.
–
30
–
0.05
–
–
–
30
28
223)
–
1.00
–
4.00
6.00
–
–
–
–
–
16
12
10
8
20
0.250
0.50
30
–
32
28
0.9
0.80
2
0.9
1.3
1.3
1.3
1.6
1.6
2.0
2.0
3.0
4.0
0.45
1.40
1.10
0.80
1.90
1.40
2.40
1.90
3.20
4.00
2
1
2
2
1
2
1
2
1
1
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
26
32
20
24
26
18
22
16
18
14
12
–
22
–
24
6.00
–
0.34
2
–
–
4.00
0.035
0.035
0.09
0.09
l
–
0.140
0.45
–
–
1.50
–
223)
0.7
26
–
0.50
10.00
28
–
–
–
32
1
–
18
203)
–
1.10
0.34
–
–
–
0.9
–
1.00
1.50
–
0.09
–
–
1
1
–
–
0.345)
0.45
0.80
–
0.05
–
0.54)
0.7
–
223)5)
14
–
min.
–
0.50
10
max.
0.345)
20
10
min.
–
12
l
22
l
l
l
223)
0.140
0.34
30
l
18
0.500
1.00
40
l
28
20
0.035
0.250
0.09
0.50
30
l
40
l
50
l
223)
0.140
0.34
40
18
0.340
1.00
50
l
65
l
90
l
143)
1.000
1.50
123)
1.500
2.50
65
103)
2.500
4.00
75
14
10
1.000
4.000
1.50
6.00
l
l
l
Note:
1) contact retention force in the insulator (according to IEC 60512-8 test 15 a).
2) for 00/TT multipole series.
3) for a given AWG, the diameter of some stranded conductor designs is larger than the solder cup diameter. Make sure that the maximum conductor
diameter is smaller than ø C.
4) for 00 /TT multipole series or for 0B/0T and 1B/1T series with male contacts.
5) for 0B.302/0B.303, 0K.302/0K.303 and 0T.302/0T.303 ø C = 1.0 mm, AWG max 20, section max (mm2) 0.50.
6) for 00/TT and 1B/1K/1T series, according to manufacturing and plating tolerance ø C min = 0.43 mm.
l First choice alternative
www.lemo.com
l Special order alternative
65
®
®
Contacts reference for plugs, free or fixed sockets
Reference
Contact type
Print
Male Female
øA
(mm)
Contact
øC
Form
(mm) per fig.
Solid
AWG Section
max.
max.
(mm2)
Conductor
Stranded
AWG
Section (mm2)
min.
max.
min.
max.
Fr 1)
(N) Notes
L
øC
øA
øA
øC
D
N
L dimensions and C are detailed in the section on PCB drilling pattern.
See page 163.
l
V
V
L dimensions and C are detailed in the section on PCB drilling pattern.
See page 164.
l
L
Print (elbow)
øA
L
øC
Note: 1) contact retention force in the insulator (according to IEC 60512-8 test 15 a).
l First choice alternative
66
l Special order alternative
www.lemo.com
®
®
Collets (B, K and T series)
D and M type collets for B series
øB
øA
D type
Reference
øA
øB
M type
Collet ø
Cable ø
Reference
Collet ø
Cable ø
Type Code
ø A
ø B
max.
min.
M
52
5.2
–
5.2
> 4.2
D
62
6.2
–
6.2
Notes
00
0B
1B
XB
2B
ø A
ø B
max.
Notes
Type Code
min.
D
22
2.2
–
2.2
D
27
2.7
–
2.7
> 2.2
D
35
3.5
2.8
3.5
> 2.7
8)
D
72
7.7
–
7.7
> 6.2
D
22
2.1
–
2.2
1.4
2)
D
92
9.2
–
9.2
> 7.7
D
32
3.2
–
3.2
> 2.2
D
10
10.2
–
10.0
> 9.2
D
42
4.2
–
4.2
> 3.2
D
11
11.0
–
11.0
> 10.0
D
12
12.0
10.2
12.0
> 11.0
M
62
6.2
–
6.2
> 5.2
5)
M
72
7.2
–
7.2
> 6.2
5)
1.4
3B
4)
4.9
D
52
5.2
4.7
5.2
> 4.2
8)
D
56
5.6
4.7
5.6
> 5.2
1) 8)
M
27
2.7
–
2.7
> 2.2
M
31
3.1
–
3.1
> 2.7
M
82
8.2
–
8.2
> 7.2
5)
D
42
4.2
–
4.2
3.1
M
92
9.2
8.6
9.2
> 8.2
6)
D
52
5.2
–
5.2
> 4.2
D
10
10.8
–
10.5
D
62
6.2
–
6.2
> 5.2
D
12
12.3
–
12.0 10.6
D
72
7.2
6.2
7.2
> 6.2
8)
D
13
13.8 12.5 13.5 12.1
D
76
7.6
6.9
7.6
> 7.2
1) 8)
D
15
15.3 12.5 15.0 13.6
7)
D
52
5.2
7.2
5.0
4.4
D
16
16.3 12.5 16.0 15.1
1)
D
62
6.2
7.2
6.0
5.4
D
11
11.8
–
11.5
D
72
7.2
7.2
7.0
6.4
D
13
13.8
–
13.5 11.6
D
82
8.2
7.2
8.0
7.4
1)
D
15
15.8
–
15.5 13.6
7)
M
21
2.1
–
2.2
1.4
3)
D
17
17.8
–
17.5 15.6
1)
M
32
3.1
–
3.2
> 2.2
3)
D
19
19.8
–
19.5 17.6
1)
D
42
4.2
–
4.2
> 3.2
D
21
21.8
–
21.5 19.6
1)
D
52
5.2
–
5.2
> 4.2
D
23
23.8 21.8 23.5 21.6
1)
D
62
6.2
–
6.2
> 5.2
D
25
25.3 21.8 25.0 23.6
1)
D
72
7.2
–
7.2
> 6.2
D
82
8.2
–
8.2
> 7.2
D
92
9.2
8.6
9.2
> 8.2
8)
D
99
9.9
8.6
9.9
> 9.2
1) 8)
4B
5B
1) 8)
9.1
9.6
Note: all dimensions are in millimetres.
1) these collets cannot be used for connector models with nut for fitting a bend relief. No bend relief available for this cable size.
2) the inner diameter of the smallest bend relief available is 2.5 mm (in TPU) / 1.7 mm (in silicone).
3) for 0B bend relief.
4) for 1B bend relief.
5) for 2B bend relief.
6) for 4B bend relief.
7) the inner diameter of the largest bend relief available is 14.5 mm.
8) for FSG model, standard cable diameter reduced as follow: 0B series (D52) = 4.7 mm, 2B series (D92) = 8.6 mm. For larger diameter use a “K” type
collet, please check online Part Search for additional details.
www.lemo.com
67
®
®
C and K type collets for K series
Reference
øB
K type
oversize
cable collet
øA
øA
øB
C type
Collet ø
Cable ø
Reference
Collet ø
Cable ø
Type Code
C
70
7.2
–
7.0
6.6
C
75
8.2
8.2
7.5
7.1
Notes
0K
1K
2K
68
ø A
ø B
max.
Notes
Type Code
min.
C
10
1.6
–
1.2
1.0
1)
C
15
1.6
–
1.5
1.3
1)
C
20
2.1
–
2.0
1.6
1)
C
80
8.2
8.2
8.0
7.6
C
25
3.1
–
2.5
2.1
C
85
9.2
8.6
8.5
8.1
C
30
3.1
–
3.0
2.6
K
90
9.2
–
9.0
8.6
4)
C
35
4.2
4.2
3.5
3.1
K
95
10.2 10.2
9.5
9.1
4)
C
40
4.2
4.2
4.0
3.6
K
10
10.2 10.2 10.0
9.6
4)
C
45
5.2
5.2
4.5
4.1
K
11
11.2 10.6 10.5 10.1
C
50
5.2
5.2
5.0
4.6
C
30
3.2
–
3.0
2.6
C
15
1.6
–
1.5
1.3
C
35
4.2
–
3.5
3.1
C
20
2.2
–
2.0
1.6
C
40
4.2
–
4.0
3.6
C
25
3.2
–
2.5
2.1
C
45
5.2
–
4.5
4.1
C
30
3.2
–
3.0
2.6
C
50
5.2
–
5.0
4.6
C
35
4.2
–
3.5
3.1
C
55
6.2
–
5.5
5.1
C
40
4.2
–
4.0
3.6
C
60
6.2
–
6.0
5.6
C
45
5.2
–
4.5
4.1
C
65
7.2
–
6.5
6.1
C
50
5.2
–
5.0
4.6
C
70
7.2
–
7.0
6.6
C
55
6.2
6.2
5.5
5.1
C
75
8.2
–
7.5
7.1
C
60
6.2
6.2
6.0
5.6
C
80
8.2
–
8.0
7.6
C
65
7.2
6.7
6.5
6.1
C
85
9.2
–
8.5
8.1
K
70
7.2
–
7.0
6.6
3)
C
90
9.2
–
9.0
8.6
K
75
8.2
8.2
7.5
7.1
3)
C
95
10.2 10.2
9.5
9.1
K
80
8.2
8.2
8.0
7.6
3)
C
10
10.2 10.2 10.0
9.6
K
85
9.2
8.6
8.5
8.1
3)
C
11
11.2 10.6 10.5 10.1
C
15
2.2
–
1.5
1.3
K
11
12.3
12.0 10.6
5)
C
20
2.2
–
2.0
1.6
K
12
13.8 13.8 12.8 12.1
5)
C
25
3.2
–
2.5
2.1
K
13
13.8 13.8 13.5 12.9
5)
C
30
3.2
–
3.0
2.6
K
14
15.3 15.3 14.0 13.6
5)
C
35
4.2
–
3.5
3.1
K
15
15.3 15.3 15.0 14.1
2)
C
40
4.2
–
4.0
3.6
C
45
5.2
–
4.5
4.1
C
50
5.2
–
5.0
4.6
C
55
6.2
–
5.5
5.1
C
60
6.2
–
6.0
5.6
C
65
7.2
–
6.5
6.1
2K
3K
ø A
ø B
–
max.
min.
4)
Note: all dimensions are in millimetres.
1) the inner diameter of the smallest bend relief available is 2.5 mm
(in TPU) / 1.7 mm (in silicone).
2) the inner diameter of the largest bend relief available is 14.5 mm.
3) for 2B bend relief.
4) for 3B bend relief.
5) for 4B bend relief.
www.lemo.com
®
®
C and K type collets for K series
øA
øB
C type
Reference
4K
Collet ø
ø B
Cable ø
Type Code
ø A
max.
min.
C
50
6.3
–
5.0
4.8
C
55
6.3
–
5.5
5.1
C
60
6.3
–
6.0
C
65
7.3
–
6.5
C
70
7.3
–
C
75
8.3
C
80
C
Reference
Notes
øA
øB
øB
øA
C type
K type
oversize
cable collet
Collet ø
max.
min.
Notes
Type Code
ø A
C
10
11.8
–
10.5
C
11
11.8
–
11.5 10.6
5.6
C
12
13.8
–
12.5 11.6
6.1
C
13
13.8
–
13.5 12.6
7.0
6.6
C
14
15.8
–
14.5 13.6
–
7.5
7.1
C
15
15.8
–
15.5 14.6
1)
8.3
–
8.0
7.6
C
16
17.8
–
16.5 15.6
1)
85
9.3
–
8.5
8.1
C
17
17.8
–
17.5 16.6
1)
C
90
9.3
–
9.0
8.6
C
18
19.8
–
18.5 17.6
1)
C
95
10.8
–
9.5
9.1
C
19
19.8
–
19.5 18.6
1)
C
10
10.8
–
10.5
9.6
C
20
21.8
–
20.5 19.6
1)
C
11
12.3
–
12.0 10.6
C
21
21.8
–
21.5 20.6
1)
C
12
13.8 13.8 12.8 12.1
C
22
23.8 23.8 22.5 21.6
1)
C
13
13.8 13.8 13.5 12.9
C
23
23.8 23.8 23.5 22.6
1)
C
14
15.3 15.3 14.0 13.6
C
15
15.3 15.3 15.0 14.1
2)
K
16
17.8
–
16.5 15.6
1)
K
17
17.8
–
17.5 16.6
1)
K
18
19.8
–
18.5 17.6
1)
K
19
19.8
–
19.5 18.6
1)
K
20
21.8
–
20.5 19.6
1)
K
21
21.8
–
21.5 20.6
1)
K
22
23.8 23.8 22.5 21.6
1)
K
23
23.8 23.8 23.5 22.6
1)
5K
ø B
Cable ø
9.6
Note: all dimensions are in millimetres.
1) these collets cannot be used for connector models with nut for fitting a bend relief. No bend relief available for this cable size.
2) the inner diameter of the largest bend relief available is 14.5 mm.
www.lemo.com
69
®
®
C and K type collets for T series
C type
K type
oversize
cable collet
Type
TT
0T
Cable ø (mm)
min. max.
C27 2.4 2.6
2T
C31 2.7 3.0
Cable ø (mm)
min. max.
Type
Note
C15 1.3 1.5
3T
C20 1.6 2.0
Cable ø (mm)
min. max.
C35 3.1 3.5
1)
C25 2.1 2.5
C40 3.6 4.0
C15 1.3 1.5
1)
C30 2.6 3.0
C45 4.1 4.5
1)
C35 3.1 3.5
C50 4.6 5.0
C25 2.1 2.5
C40 3.6 4.0
C55 5.1 5.5
C30 2.6 3.0
C45 4.1 4.5
C60 5.6 6.0
C35 3.1 3.5
C50 4.6 5.0
C65 6.1 6.5
C40 3.6 4.0
C55 5.1 5.5
C70 6.6 7.0
C45 4.1 4.5
C60 5.6 6.0
C75 7.1 7.5
K50 4.6 5.0
2)
C65 6.1 6.5
C80 7.6 8.0
K55 5.1 5.5
2)
C70 6.6 7.0
C85 8.1 8.5
K60 5.6 6.0
2)
C75 7.1 7.5
C90 8.6 9.0
2)
C80 7.6 8.0
C95 9.1 9.5
C15 1.3 1.5
C85 8.1 8.5
C10 9.6 10.0
C20 1.6 2.0
K90 8.6 9.0
4)
C11 10.1 10.5
C25 2.1 2.5
K95 9.1 9.5
4)
K11 10.6 12.0
C30 2.6 3.0
K10 9.6 10.0
4)
K12 12.1 12.8
C35 3.1 3.5
K11 10.1 10.5
4)
K13 12.9 13.5
K65 6.1 6.5
Note
C30 2.6 3.0
C10 1.0 1.2
C20 1.6 2.0
1T
Type
Note
C40 3.6 4.0
K14 13.6 14.0
C45 4.1 4.5
K15 14.1 15.0
5)
C50 4.6 5.0
C55 5.1 5.5
C60 5.6 6.0
C65 6.1 6.5
K70 6.6 7.0
3)
K75 7.1 7.5
3)
K80 7.6 8.0
3)
K85 8.1 8.5
3)
Note: all dimensions are in millimetres.
1) the inner diameter of the smallest bend relief available is 2.5 mm (in TPU) / 1.7 mm (in silicone).
2) for 1B bend relief.
3) for 2B bend relief.
4) for 3B bend relief.
5) the inner diameter of the largest bend relief available is 14.5 mm.
70
www.lemo.com
®
®
Variant (B, K and T series)
Bend relief for B series models with collet
Need to be ordered
Ref.
Collet
Type
Code
Bend relief for K series models with collet
Need to be ordered
Need to be ordered
separately
(see pages 145 and 146)
Ref.
00
Z
D
22 to 35
GMA.00.lll.ll
GMB.00.lll.ll
0K
Z
0B
Z
D
22 to 52
GMA.0B.lll.ll
1K
Z
1B
Z
M
27 and 31
GMA.1B.lll.ll
D
42 to 72
GMA.1B.lll.ll
2K
Z
XB
Z
D
52 to 72
GMA.1B.lll.ll
3K
Z
2B
Z
M
21 and 32
GMA.0B.lll.ll
D
42 to 92
GMA.2B.lll.ll
4K
3B
Z
M
52
GMA.1B.lll.ll
5K
4B
5B
Z
Z
D
62 to 10
GMA.3B.lll.ll
M
62 to 82
GMA.2B.lll.ll
M
92
GMA.4B.lll.ll
D
10 to 15 1)
GMA.4B.lll.ll
D
11 to 15 1)
GMA.4B.lll.ll
Collet
Type
Code
Need to be ordered
separately
(see pages 145 and 146)
C
10 to 50
GMA.0B.lll.ll
C
15 to 65
GMA.1B.lll.ll
K
70 to 85
GMA.2B.lll.ll
C
15 to 85
GMA.2B.lll.ll
K
90 to 10
GMA.3B.lll.ll
C
30 to 10
GMA.3B.lll.ll
15 2)
K
11 to
GMA.4B.lll.ll
Z
C
50 to 15 3)
GMA.4B.lll.ll
Z
C
10 to 14
GMA.4B.lll.ll
Note: all dimensions are in millimetres.
1) for D15 see page 67.
2) for K15 see page 68.
3) for C15 see page 69.
Bend relief for T series models with collet
Need to be ordered
Ref.
TT
Z
0T
Z
1T
Z
www.lemo.com
Collet
Type
Code
Need to be ordered
separately
(see pages 145 and 146)
C
27 and 31
GMB.00.lll.ll
C
10 to 45
GMA.0B.lll.ll
K
50 to 65
GMA.1B.lll.ll
C
15 to 65
GMA.1B.lll.ll
K
70 to 85
GMA.2B.lll.ll
Ref.
2T
Z
3T
Z
Collet
Type
Code
Need to be ordered
separately
(see pages 145 and 146)
C
15 to 85
GMA.2B.lll.ll
K
90 to 10
GMA.3B.lll.ll
C
30 to 10
GMA.3B.lll.ll
K
11 to 15 4)
GMA.4B.lll.ll
Note: all dimensions are in millimetres.
4) for K15 see page 70.
71
®
®
Colour of the bridge plug shells and connectors shell made of plastic material and aluminium alloys
Bridge plug and plastic shell
Ref.
Colour
A
blue
B
PSU
PPSU
Aluminium alloys
PA.6
Anodized colour
l
l
white
l
l
G
grey
l
l
J
yellow
l
M
brown
l
N
black
l
l
R
red
l
l
S
orange
l
l
T
natural
l
V
green
l
l
L
black
l
X
natural
l
F
cream
l
Watertight and vacumtight socket and coupler
models (B, K and T series) (not connected)
Reference
Watertight Vacuumtight
72
Anodized colour
for bend relief collet nut
Model
YHl, HGl, HNl, HHl,
HCl, HEl, HMl, Sll
B
P
K
P
PV
HGl, HEl, Sll
T
P
PV
HGl, HEl, HMl
PV
Note: other anodizing colours are available for
connectors with collet nut for bend relief. Please
consult us.
O-ring and gasket material (K and T series)
Standard connectors are delivered with silicone o-ring and
gaskets. The vacuumtight models, identified with the letter
«PV», are delivered with Viton® gaskets. Other gaskets
material can be delivered upon special request.
O-ring material
Ref.
H
FPM (Viton®)
E
EPDM
D
FPM (Viton®) and collet nut for bend relief
www.lemo.com
E SERIES (watertight)
S SERIES
®
®
S Series
S series connectors have main features as follows:
– security of the Push-Pull self-latching system
– solder or print contacts (straight or elbow)
– unipole types transmitting current up to 230 A
– polarisation by stepped insert (half-moon)
and multipole types with up to 106 contacts fitted with male and female contacts
– 360° screening for full EMC shielding.
Metal housing models (page 76)
Fixed plug
Straight plugs
Fixed sockets
Free sockets
FAA
FFA, FFP*
ERA
EEP
FFA
ERN
ERD
PCA, PCP*
Elbow plugs
PCA
FLM
FFA, FFP*
FLA
FFB
FFE
FLS
ERC
PCA, PCP*
ECP
ERS*
PZP*
ECP
EHP
Fixed sockets
ECP
PSA, PSP
FFL*
Free coupler
EBD*
PSS
FFF
RMA
EBS*
Fixed coupler
FFS
FZP*
FTA*
EBC*
RAD
Note: * Contact LEMO for details.
New design models (page 86)
Straight plugs
T-plug
Free sockets
Elbow socket models (page 87)
FGZ
PGZ
Elbow sockets
FGZ
PGZ
EPL
Plastic housing models (page 89)
Straight plugs
EXP
Watertight or vacuumtight models (page 91)
Fixed socket
Fixed sockets
Fixed coupler
FFA, FFP
HGP
FFP
FFL
74
EWB
SWH
ERN
HCP
HGW
www.lemo.com
®
Part Numbering System
®
F F A . 1 S . 3 0 4 . C L A C 3 2
Plug
P C A . 1 S . 3 0 4 . C L L C 3 2 Z
Free socket
Variant: (page 121)
Cable ø: (page 115)
Collet type: (page 115)
E R A . 1 S . 3 0 4 . C L L
Fixed socket
R A D . 1 S . 3 0 4 . C L L
Coupler
Variant: (page 121)
Model: (page 76)
Contact: (page 112)
Series: (page 76)
Insulator: (page 112)
Insert configuration: (p. 103)
Housing: (page 112)
FFA.1S.304.CLAC32 = straight plug with cable collet, 1S series, multipole type with 4 contacts, outer shell in chrome-plated brass,
PEEK insulator, 2 male and 2 female solder contacts, C type collet for a 3.2 mm diameter cable.
PCA.1S.304.CLLC32Z = free socket, with cable collet, 1S series, multipole type with 4 contacts, outer shell in chrome-plated brass,
PEEK insulator, 2 female and 2 male solder contacts, C type collet for a 3.2 mm diameter cable and nut for fitting a bend relief.
ERA.1S.304.CLL = fixed socket, nut fixing, 1S series, multipole type with 4 contacts, outer shell in chrome-plated brass, PEEK insulator,
2 female and 2 male solder contacts.
RAD.1S.304.CLL = straight coupler, nut fixing, 1S series, multipole type with 4 contacts, outer shell in chrome-plated brass, PEEK
insulator, 2 female and 2 male contacts each end.
Part Section Showing Internal Components
Straight plug
Fixed socket
1 outer shell
2 earthing crown
3 retaining ring
hexagonal nut
5 locking washer
4
6 insulator
7 male contact
8 female contact
www.lemo.com
6
2
3
1
4
5
8
7
1
7
6
5
4
2
8
3
1 outer shell
2 latch sleeve
3 collet nut
4 centre-piece
5 insulator
6 male contact
7 female contact
8 collet
75
®
®
Metal housing models
Technical Characteristics
Electrical
Mechanical and Climatical
Characteristics
Endurance1)
Value
> 5000 cycles
Humidity
Standard
IEC 60512-5 test 9a
up to 95% at 60° C
Temperature range
- 55° C, + 250° C
Resistance to vibrations
10-2000 Hz, 15g IEC 60512-4 test 6d
Shock resistance
100 g, 6 ms
IEC 60512-4 test 6c
Salt spray corrosion test2)
> 1000h
IEC 60512-6 test 11f
Protection index (mated)
IP 50
IEC 60529
Climatical category
55/175/21
IEC 60068-1
Characteristics
Shielding
efficiency
Value
Standard
at 10 MHz
> 75 dB
IEC 60169-1-3
at 1 GHz
> 40 dB
IEC 60169-1-3
Note:
The various tests have been carried out with FFA and ERA connector
pairs, with chrome-plated brass shell and PEEK insulator.
Detailed electrical characteristics, as well as materials and treatment are
presented in the chapter Technical Characteristics on page 182.
1) see page 189, contact resistance after mating cycles. See page 185,
mechanical endurance latching force.
2) for chrome plated product (« C » material code).
FFA Straight plug, cable collet
Reference
Dimensions (mm)
Model Series A
~L
øA
~M
S2
L
M S2
FFA
00
6.4 26.0 18.0 4.5
FFA
0S
9.0 34.5 24.5 6.5
FFA
1S
12.0 42.5 31.5 8.5
FFA
2S
14.8 52.0 40.0 11.0
FFA
3S
17.8 61.0 46.0 14.0
FFA
4S
24.8 77.0 59.0 19.0
FFA
5S
35.0 103.0 78.0 29.0
FFA
6S
46.0 106.0 81.0 38.0
M1 Cable assembly (pages 175 to 177)
FFA Straight plug with oversize cable collet 1)
Reference
Dimensions (mm)
Model Series A
~L
øA
øB
~M
S2
76
S1
B
L
M S1 S2
FFA
00
6.4 8.0 34.0 26.0 7.0 6.5
FFA
0S
9.0 10.0 45.5 35.5 9.0 8.5
FFA
1S
12.0 13.0 57.0 46.0 12.0 11.0
FFA
2S
14.8 18.0 67.0 55.0 14.0 14.0
FFA
3S
17.8 21.0 85.0 70.0 19.0 19.0
FFA
4S
24.8 31.8 107.0 89.0 28.5 29.0
FFA
5S
35.0 41.8 138.0 113.0 37.5 38.0
M2 Cable assembly (pages 175 and 178)
Note: 1) correspond to K type of collet, the fitting of oversize collets onto
this model allows them to be fitted to the cables that can be accommodated
by the next housing size up (see page 115).
www.lemo.com
®
FFA
Straight plug, cable collet and nut for fitting a bend relief 1)
Reference
~L
øA
~M
S2
Model
Series
FFA
00
FFA
0S
FFA
1S
FFA
2S
FFA
3S
FFA
4S
®
Dimensions (mm)
A
L
M
6.4 26.0 18.0
S2
6
9.0 34.5 24.5
12.0 42.5 31.5
7
9
14.8 52.0 40.0
12
24.8 77.0 59.0
20
17.8 61.0 46.0
14
M1 Cable assembly (pages 175 and 176)
FFB
Straight plug, cable collet and safety locking ring
Note: 1) to order, add a «Z» at the end of the reference.
The bend relief must be ordered separately (see page 145).
Reference
~L
øA
~M
S2
Model
Series
FFB
0S
FFB
1S
FFB
2S
FFB
3S
Dimensions (mm)
A
L
M
9.0 36.8 26.8
S2
6.5
12.0 45.0 34.0
8.5
14.8 55.5 43.5 11.0
17.8 65.0 50.0 14.0
M1 Cable assembly (pages 175 and 176)
FFE
Note: nut for fitting a bend relief (available only for size 1S).
Straight plug, cable collet, front seal and nut for fitting a bend relief 1) (protected to IP54 when mated)
Reference
~L
Model
Series
FFE
00
FFE
0S
FFE
1S
FFE
2S
FFE
3S
øA
~M
S2
Dimensions (mm)
A
L
M
7.4 26.0 18.0
10.0 34.5 24.5
13.0 42.5 31.5
16.0 52.0 40.0
19.0 61.0 46.0
S2
6
7
9
12
14
M1 Cable assembly (pages 175 and 176)
Note: 1) to order, add a «Z» at the end of the reference.
The bend relief must be ordered separately (see page 145).
www.lemo.com
77
®
FFF
®
Straight plug, non-latching, cable collet
Reference
~L
øA
~M
S2
FFS
Model
Series
FFF
00
FFF
0S
FFF
1S
FFF
2S
Dimensions (mm)
A
L
M
6.4 26.0 18.0
9.0 34.5 24.5
12.0 42.5 31.5
S2
4.5
6.5
8.5
14.8 52.0 40.0 11.0
M1 Cable assembly (pages 175 and 176)
Straight plug for cable crimping
L
øA
M
S1
S2
Reference
Model
Series
FFS
00
A
6.4
Dimensions (mm)
L
31
M
23
M5 Cable assembly (page 175)
FAA
Reference
L maxi
øA
M
e
øB
E maxi
5.5
S2
5.5
Note: Model available only with crimp backnut E31 similar to 00.250 series.
Fixed plug non-latching, nut fixing
S3
S1
S1
Model
Series
FAA
00
FAA
0S
FAA
1S
FAA
2S
FAA
3S
FAA
4S
FAA
5S
FAA
6S
A
8
B
10.2
10 12.4
e
Dimensions (mm)
E
M7x0.5 2.0
L
–
L1)
15.5
M
9.0
M9x0.6 2.0 18.5 18.0 11.2
S1
6.3
S3
9
8.2 11
14 15.8 M12x1.0 2.5 22.5 21.7 12.5 10.5 14
18 19.2 M15x1.0 4.0 25.0 25.3 13.8 13.5 17
22 25.0 M18x1.0 4.0 31.0 29.0 17.0 16.5 22
28 34.0 M25x1.0 2.5 35.5 39.0 20.5 23.5 30
40 40.0 M35x1.0 2.5 45.0
54 54.0 M48x1.5 2.5 45.0
P1 Panel cut-out (page 158)
–
–
28.0 33.5
28.0
–
–
–
P2 Panel cut-out 6S series (page 158)
Note: 1) unipole model
78
www.lemo.com
®
®
FLC/FLM
Elbow (90°) plug, cable collet
Reference
L
Model
~H
øA
M
S2
S1
FLA
Series
FLC
00
FLM
0S
FLM
1S
FLM
2S
fig. 1
fig. 2
A
A1
M
7.5 16.5 19.5 11.5
9.5 23.0 30.0 20.0
12.0 29.0 36.0 25.0
S1
S2
7.0
8
4.5
9.0
14.8 35.0 41.5 29.5 12.0
~H
Model
Series
FLA
3S
FLA
4S
FLA
5S
FLA
6S
A
A1
28
28
21
–
–
Dimensions (mm)
H
L
6
10
13
M
S1
S2
20
19
21
44.0 38.5 23.5
15
37
76.5 65.0 40.0
30
48
56.0 49.0 31.0
94.0 81.0 56.0
M3 Cable assembly (pages 175 to 177)
S1
40
14
29
38
Note:
fig. 1 is used for the unipole type, fig. 2 is used for the multipole type.
S2
FLS
L
Note: FLC.00 model is used for the unipole type.
For 0S, 1S and 2S series use «D» type collet, see page 67.
Reference
M
H
M3 Cable assembly (pages 175 to 177)
Elbow (90°) plug, cable collet
L
A
Dimensions (mm)
l Maximum operating temperature: 120°C
Elbow (90°) plug for cable crimping
L
H
M
A
Reference
Model
Series
FLS
00
Dimensions (mm)
A
9
H
16
L
17.5
M6 Cable assembly (page 175)
M
9.5
Note: Model available only with crimp backnut E31 similar to 00.250 series.
l Maximum operating temperature: 120°C
www.lemo.com
79
®
®
ERA Fixed socket, nut fixing
Dimensions (mm)
Reference
Model Series A B
L maxi
øA
M
e
øB
S3
E maxi
S1
e
E
L L1) M S1 S3
ERA
00
ERA
0S
10 12.4 M9x0.6 7.0 18.5 18.0 1.2 8.2 11
ERA
1S
14 15.8 M12x1.0 7.5 21.0 20.5 1.5 10.5 14
ERA
2S
18 19.2 M15x1.0 8.5 24.5 23.5 1.8 13.5 17
ERA
3S
22 25.0 M18x1.0 11.5 29.0 27.5 2.0 16.5 22
ERA
4S
28 34.0 M25x1.0 12.0 34.0 33.5 2.5 23.5 30
ERA
5S
40 40.0 M35x1.0 15.5 45.0 78.5 3.0 33.5 –
ERA
6S
54 54.0 M48x1.5 16.0 45.0 – 3.5 45.5 –
8 10.2 M7x0.5 5.5 – 14.5 1.0 6.3 9
P1 Panel cut-out (page 158)
Note: 1) unipole model.
Note: The 5S series is delivered with a tapered washer and a round nut.
The 6S series is delivered without a locking washer and with a round nut.
ERN Fixed socket, nut fixing, with earthing tag
L maxi
øA
Model Series A B
e
øB
Dimensions (mm)
Reference
M
S3
E maxi
S1
e
E
L L1) M S1 S3
ERN
0S
10 12.4 M9x0.6 7.0 19.3 19.3 1.2 8.2 11
ERN
1S
14 15.8 M12x1.0 7.5 22.4 22.4 1.5 10.5 14
ERN
2S
18 19.2 M15x1.0 8.5 26.3 26.3 1.8 13.5 17
ERN
3S
22 25.0 M18x1.0 11.5 29.8 29.8 2.0 16.5 22
P1 Panel cut-out (page 158)
Note: 1) unipole model
ERC Fixed socket, nut fixing with slot in the flange
L maxi
S3
M
Dimensions (mm)
Reference
F
E maxi
S1
øA
e
øB
Model Series A
B
e
E
F
L
L1) M S1 S3
ERC
00
8 10.2 M7x0.5 5.5 1.6 – 14.5 1.0 6.3 9
ERC
0S
10 12.4 M9x0.6 7.0 2.0 18.5 18.0 1.2 8.2 11
ERC
1S
14 15.8 M12x1.0 7.5 2.5 20.2 20.5 1.5 10.5 14
P1 Panel cut-out (page 158)
Note: 1) unipole model.
80
www.lemo.com
®
®
EHP Fixed socket, nut fixing, protruding shell
øA
Model Series A B
e
øB
M
E maxi
Dimensions (mm)
Reference
L maxi
S3
S1
e
E
L L1) M S1 S3
EHP
0S
10 12.4 M9x0.6 2.0 20.5 18.0 12.5 8.2 11
EHP
1S
14 15.8 M12x1.0 3.5 20.2 20.5 12.0 –
14
EHP
3S
22 25.0 M18x1.0 4.0 29.0 29.0 18.7 –
22
P1 Panel cut-out 0S series (page 158)
P2 Panel cut-out (page 158)
Note: 1) unipole model
EEP Fixed socket, nut fixing (back panel mounting)
L maxi
P
S2 S1
M
øA
e
øB
Reference
E maxi
Dimensions (mm)
Model Series A
B
e
E
L
L1) M P S1 S2
EEP
1S
16 16.0 M12x1.0 6.5 20.2 20.5 3.5 11 10.5 13
EEP
2S
20 19.5 M15x1.0 4.3 24.5 23.5 3.5 9 13.5 15
P1 Panel cut-out (page 158)
Note: 1) unipole model.
ERD Fixed socket with two nuts (back panel mounting)
Dimensions (mm)
Reference
Model Series A B
L maxi
S 1 E maxi
øA
M
e
øB
S3
e
E
L L1) M S1 S3
ERD
0S
12 12.4 M9x0.6 5.5 18.5 18.0 2.5 8.2 11
ERD
1S
16 15.8 M12x1.0 6.0 20.2 20.5 3.5 10.5 14
ERD
2S
20 19.2 M15x1.0 6.5 24.5 23.5 3.5 13.5 17
ERD
3S
24 25.0 M18x1.0 9.0 29.0 27.5 4.5 16.5 22
ERD
4S
30 34.0 M25x1.0 10.0 34.0 33.5 4.5 23.5 30
P1 Panel cut-out (page 158)
Note: 1) unipole model.
Note: The 3S and 4S series are delivered with a conical nut.
www.lemo.com
81
®
®
ECP Fixed socket with two nuts, long threaded shell (back panel mounting)
Dimensions (mm)
Reference
L maxi
Model Series A B
e
øB
S1
øA
M
S3
E maxi
e
E
L L1) M S1 S3
ECP
0S
12 12.4 M9x0.6 8.5 18.5 18.5 2.5 8.2 11
ECP
1S
16 15.8 M12x1.0 10.0 20.2 20.5 3.5 10.5 14
ECP
2S
20 19.2 M15x1.0 11.0 24.5 26.0 3.5 13.5 17
ECP
3S
24 25.0 M18x1.0 14.0 29.0 30.0 4.5 16.5 22
P1 Panel cut-out (page 158)
Note: 1) unipole model.
Note: The 3S series is delivered with a conical nut.
ECP Fixed socket with two nuts, long threaded shell, straight contact for printed circuit (back panel mounting)
Dimensions (mm)
Reference
Model Series A B
N
M
e
øB
S3
øA
L
e
E M N S1 S3
ECP
0S
12 12.4 M9x0.6 8.5 2.5 15.0 8.2 11
ECP
1S
16 15.8 M12x1.0 10.0 3.5 17.5 10.5 14
ECP
2S
20 19.2 M15x1.0 11.0 3.5 20.0 13.5 17
ECP
3S
24 25.0 M18x1.0 14.0 4.5 24.0 16.5 22
P1 Panel cut-out (page 158)
S1
E maxi
P21 PCB drilling pattern (page 166)
Note: The 3S series is delivered with a conical nut.
Note: this contact type is available for all Ell socket models.
See page 167 for table of available types.
Length «L» depends on the number of contacts, see table on page 167.
ECP Fixed socket with two nuts, long threaded shell, elbow (90°) contacts for printed circuit (back panel mounting)
Dimensions (mm)
Reference
Model Series A B
L
N
20 mini
E maxi
øA
M
e
øB
S3S1
e
E M N S1 S3
ECP
0S
ECP
1S
16 15.8 M12x1.0 10.0 3.5 17.5 10.5 14
ECP
2S
20 19.2 M15x1.0 11.0 3.5 20.0 13.5 17
ECP
3S
24 25.0 M18x1.0 14.0 4.5 24.0 16.5 22
12 12.4 M9x0.6 8.5 2.5 15.0 8.2 11
P1 Panel cut-out (page 158)
P24 PCB drilling pattern (page 168)
2
Note: The 3S series is delivered with a conical nut.
Note: this contact type is available for all back panel mounting socket
types. See page 168 for available types.
Length «L» depends on the number of contacts, see PCB drilling pattern on page 168.
82
www.lemo.com
®
PCA
Free socket, cable collet
Reference
øA
~L
S2
PCA
Model
Series
PCA
00
PCA
0S
PCA
1S
PCA
2S
PCA
3S
PCA
4S
PCA
5S
PCA
6S
Reference
Model
A
L
S2
33.5
6.5
6.5
25.0
11.9
40.5
8.9
14.8
17.8
24.8
34.7
4.5
8.5
50.0 11.0
59.0 14.0
75.0 19.0
99.0 29.0
46.0 102.0 38.0
Series
PCA
00
PCA
0S
PCA
1S
PCA
2S
PCA
3S
PCA
4S
A
6.5
Dimensions (mm)
B
8.0
8.9 10.0
11.9 13.0
14.8 18.0
17.8 21.0
L
33.0
44.5
S1
S2
9.0
8.5
7.0
6.5
55.0 12.0 11.0
65.0 14.0 14.0
83.0 19.0 19.0
24.8 31.8 105.0 28.5 29.0
M2 Cable assembly (pages 175 and 178)
øA
øB
~L
PCA
Dimensions (mm)
M1 Cable assembly (pages 175 to 177)
Free socket with oversize cable collet 1)
S2
®
Note: 1) correspond to K type of collet, the fitting of oversize collets onto
this model allows them to be fitted to the cables that can be accommodated
by the next housing size up (see page 115).
S1
Free socket, cable collet and nut for fitting a bend relief 1)
Reference
øA
~L
S2
Model
Series
PCA
00
PCA
0S
PCA
1S
PCA
2S
PCA
3S
PCA
4S
Dimensions (mm)
A
L
6.5 25.0
8.9 33.5
11.9 40.5
S2
6
7
9
14.8 50.0
12
24.8 75.0
20
17.8 59.0
14
M1 Cable assembly (pages 175 and 176)
Note: 1) to order, add a «Z» at the end of the reference.
The bend relief must be ordered separately (see page 145).
www.lemo.com
83
®
®
PSA Fixed socket, nut fixing, cable collet
Dimensions (mm)
Reference
Model Series A B
~L
øB
e
E maxi
S2
M
øA
S3
S1
e
E
L M S1 S2 S3
PSA
00
PSA
0S
10 12.4 M9x0.6 7.0 33.5 1.2 8.2 6.5 11
PSA
1S
14 15.8 M12x1.0 7.5 40.5 1.5 10.5 8.5 14
PSA
2S
18 19.2 M15x1.0 8.5 50.0 1.8 13.5 11.0 17
PSA
3S
22 25.0 M18x1.0 11.5 59.0 2.0 16.5 14.0 22
PSA
4S
28 34.0 M25x1.0 12.0 75.0 2.5 23.5 19.0 30
PSA
5S
40 40.0 M35x1.0 15.5 99.0 3.0 33.5 29.0 –
PSA
6S
54 54.0 M48x1.5 16.0 102.0 3.5 45.5 38.0 –
8 10.2 M7x0.5 5.5 25.0 1.0 6.3 4.5 9
M1 Cable assembly (pages 175 to 177)
P1 Panel cut-out (page 158)
Note: the 5S series is delivered with a tapered washer and a round nut.
The 6S series is delivered without a locking washer and with a round nut.
PSP Fixed socket, nut fixing, cable collet and inner anti-rotating device
~L
S3
M
Dimensions (mm)
Reference
E maxi
S2
øB
e
øA
Model Series A B
S1
e
E
L M S1 S2 S3
PSP
2S
18 19.2 M15x1.0 8.5 50.0 1.8 13.5 11.0 17
PSP
3S
22 25.0 M18x1.0 11.5 59.0 2.0 16.5 14.0 22
PSP
4S
28 34.0 M25x1.0 12.0 75.0 2.5 23.5 19.0 30
M1 Cable assembly (pages 175 and 176)
P1 Panel cut-out (page 158)
PSS Fixed socket, nut fixing for cable crimping
L
S3
M
øB
øA
e
Reference
Model Series A B
PSS
S2
E maxi
Dimensions (mm)
00
e
E
L M S1 S2 S3
8 10.2 M7x0.5 5.5 30 1 6.3 5.5 9
S1
M5 Cable assembly (page 175)
P1 Panel cut-out (page 158)
Note: Model available only with crimp backnut E31 similar to 00.250 series.
84
www.lemo.com
®
®
RMA Free coupler
Reference
øA
~L
Model
Series
RMA
00
RMA
0S
RMA
1S
RMA
2S
RMA
3S
RMA
4S
RMA
5S
Dim. (mm)
A
L
6.4 22.0
8.9 25.0
11.9 28.5
14.8 31.5
17.8 38.5
24.8 46.5
34.7 60.5
Note: see page 114 for the available plug and contact configurations and
in order to ensure correct contact alignment.
RAD Fixed coupler, nut fixing
Reference
L
øA
e
E maxi
Series
RAD
00
RAD
0S
RAD
1S
RAD
2S
RAD
3S
RAD
4S
RAD
5S
M
S1
øB
S3
Model
A
8
B
10.2
10 12.4
Dimensions (mm)
e
M7x0.5
M9x0.6
14 15.8 M12x1.0
18 19.2 M15x1.0
E
L
M
5.5 22.0 1.0
7.0 25.0 1.2
S1
6.3
S2
9
8.2 11
7.5 28.5 1.5 10.5 14
8.5 31.5 1.8 13.5 17
22 25.0 M18x1.0 11.5 38.5 2.0 16.5 22
28 34.0 M25x1.0 12.0 46.5 2.5
40 40.0 M35x1.0 15.5 60.5 3.0
P1 Panel cut-out (page 158)
–
–
30
–
P2 Panel cut-out 4S and 5S series (page 158)
Note: the 5S series is delivered with a tapered washer and a round nut.
Note: See page 114 for the available plug and contact configurations
and in order to ensure correct contact alignment.
www.lemo.com
85
®
®
New design models
FGZ Straight plug, cable collet
Reference
~L
Model
Series
FGZ
0S
FGZ
1S
FGZ
2S
øA
~M
S2
S1
A
9.5
12.0
15.0
Dimensions (mm)
L
36
43
50
M
S1
S2
32
10
9
26
38
M1 Cable assembly (page 169)
8
13
7
12
Note: D type collets of the B series are used in this model (see page 67).
FGZ Straight plug, cable collet and nut for fitting a bend relief 1)
~L
Model
Series
FGZ
0S
FGZ
1S
FGZ
2S
øA
~M
S2
S1
Reference
A
9.5
12.0
15.0
Dimensions (mm)
L
35
42
49
M
S1
31
10
25
37
M1 Cable assembly (page 169)
8
13
S2
7
9
12
Note: D type collets of the B series are used in this model (see page 67).
Note: 1) to order, add a «Z» at the end of the reference.
The bend relief must be ordered separately (see page 145).
PGZ Free socket, cable collet
Reference
Model
Series
PGZ
0S
PGZ
1S
PGZ
2S
øA
~L
S2
S1
A
Dim. (mm)
L
9.5 35.5
12.5 40.5
15.0 49.0
S1
S2
10
9
8
13
M1 Cable assembly (page 169)
7
12
Note: D type collets of the B series are used in this model (see page 67).
PGZ Free socket, cable collet and nut for fitting a bend relief 1)
øA
~L
S2
86
S1
Reference
Model
Series
PGZ
0S
PGZ
1S
PGZ
2S
A
Dim. (mm)
L
9.5 34.5
12.5 39.5
15.0 48.0
S1
S2
10
9
8
13
M1 Cable assembly (page 169)
7
12
Note: D type collets of the B series are used in this model (see page 67).
Note: 1) to order, add a «Z» at the end of the reference.
The bend relief must be ordered separately (see page 145).
www.lemo.com
®
®
Elbow socket models
Technical Characteristics
Materials and Treatment
Types
Component
Surface
Treat. (µm)
Material
Cu Ni Au
PPS 1) –
Housing
Series
Type
1
0S, 1S
3
303
2
304
2
3
3
1
2
3
5
4
2
3
0.5 3 –
Insulator
PEEK –
Female contact
Bronze
0.5 3 1.5
1
4
3
2
4
2
306
3
4
1.20
4.5
Types
Model Series
1S
5
Bronze
Rated
current (A)
4
305
6
Earthing crown
Test voltage
(kV rms)1)
1
1S
1
0.5 3 –
3
0S, 1S
1
Brass
Electrical
1
2
Metallic parts
Note: 1) not used for all sizes.
The surface treatment standards are as follows:
– Nickel SAE AMS QQ N 290
– Gold: ISO 27874
2
2
2
0.5 3 –
1
302
0S, 1S
Brass
1
5
16
5
4
EPL
0S
EXP
0S
EPL
1S
EXP
1S
EPL
1S
EXP
1S
302-303-304
302-303-304
1.20
4.5
305-306
0.70
4.5
Note: 1) see calculation method, caution and suggested standard on
page 190.
EPL Elbow (90°) socket for printed circuit (solder or screw fixing)
Dimensions (mm)
Part number
øA
7.62
A
L
K
H
I
K
L
N
EPL.0S.302.HLN
EPL.0S.303.HLN
9 14.6 6.7 12.6 13.3 25 11.7
EPL.0S.304.HLN
EPL.1S.302.HLN
EPL.1S.303.HLN
EPL.1S.304.HLN
11 16.6 7.5 14.0 13.3 27 12.6
EPL.1S.305.HLN
EPL.1S.306.HLN
3.2
H
I
N
D
ø 0.7
M 1.6
D
Note: to replace the 4 ground pins by 4 screws (M1.6) add an «S» to the
end of the part number. (e.g.: EPL.1S.303.HLNS)
P22 PCB drilling pattern (page 168)
www.lemo.com
87
®
®
EPL Elbow (90°) socket for printed circuit
7
øA
5.08
L
Dimensions (mm)
Part number
H
I
A
EPL.00.113.NLN
ø 0.7
H
I
6.8 10
7
P23 PCB drilling pattern (page 168)
EPL Elbow (90°) socket for printed circuit
K
5.08
2.54
L
N
Dimensions (mm)
Part number
øA
I
3
A
ø1
EPL.0S.116.DTL
D
H
8.8 16 12
I
K
L
N
9 7.7 22.7 9
Note: available only in unipole version.
D
P23 PCB drilling pattern (page 168)
EXP Elbow (90°) socket for printed circuit with two nuts (solder or screw fixing)
Dimensions (mm)
Part number
A B
N
7.62
K
L
S3
øA
e
E H
I
K L M N S3
EXP.0S.302.HLN
EXP.0S.303.HLN
12 12.4 14.6 M9x0.6 6.0 6.7 12.6 13.3 25 2.5 11.7 11
EXP.0S.304.HLN
EXP.1S.302.HLN
EXP.1S.303.HLN
EXP.1S.304.HLN
14 15.0 16.6 M11x0.5 7.5 7.5 14.0 13.3 27 3.5 12.6 13
EXP.1S.305.HLN
EXP.1S.306.HLN
3.2
øB
H
I
e
M
D
ø 0.7
M 1.6
E maxi
D
2.54
Note: to replace the 4 ground pins by 4 screws (M1.6) add an «S» to the end of the
part number. (e.g.: EXP.1S.303.HLNS).
P2 Panel cut-out 0S series (page 158)
P10 Panel cut-out 1S series (page 158)
P22 PCB drilling pattern (page 168)
88
www.lemo.com
®
®
Plastic housing models
These connectors are particularly recommended for all applications requiring maximum electrical insulation when mated. The
design, including a latch sleeve and a metal earthing crown, guarantees EMC screening efficiency to meet most requirements.
Technical Characteristics
Mechanical and Climatical
Colour
Characteristics
PEEK
natural (beige)
black
Value
POM
PSU
Standard
PPSU
white or grey
cream
> 5000 cycles
> 5000 cycles
Temperature range
- 50° C/+ 250° C
- 50° C/+ 115° C
- 50° C/+ 150° C
- 50° C/+ 180° C
Resistance to organic solvents
very good
very good
limited
good
Humidity
Sterilization
resistance2)
> 200 cycles
> 5000 cycles
–
Endurance1)
up to 95% at 60° C
none
~20 cycles
> 5000 cycles
IEC 60512-5 test 9a
> 100 cycles
–
–
IEC 60601-1 § 44.7
–
Note: 1) see page 189, contact resistance after mating cycles. See page 185, mechanical endurance latching force. 2) Steam sterilization
FFA
FFP
Straight plug, cable collet, PEEK or POM outer shell
Straight plug, cable collet, PEEK or POM outer shell and inner anti-rotating device
Reference
~L
øA
~M
S2
FFP
Model
Series
FFA
00
FFP
1S
FFP
2S
FFP
3S
Dimensions (mm)
A
L
M
7
33.5 25.5
15
52.0 40.0
12
18
S2
6
42.5 31.5
10
61.0 46.0
14
12
M1 Cable assembly (pages 175 and 176)
Straight plug, cable collet, PEEK or POM outer shell, inner anti-rotating device
and nut for fitting a bend relief 1)
Reference
~L
øA
~M
S2
Model
Series
FFP
1S
FFP
2S
FFP
3S
Dimensions (mm)
A
L
M
12
41.5 30.5
18
61.0 46.0
15
51.0 39.0
S2
10
12
14
M1 Cable assembly (pages 175 and 176)
Note: 1) to order, add a «Z» at the end of the reference.
The bend relief must be ordered separately (see page 145).
www.lemo.com
89
®
FFL
®
Straight plug, cable collet, with PSU and PPSU outer shell, inner anti-rotating device
and nut for fitting a bend relief 1)
Reference
~L
øA
~M
Model
Series
FFL
2S
Dimensions (mm)
A
L
M
16.5 51.5 39.5
M4 Cable assembly (page 177)
S2
S2
13
Note: 1) to order, add a «Z» at the end of the reference.
The bend relief must be ordered separately (see page 145).
ERN
Note: This model is fitted with a «D or M» type collet system. It is also
adapted for crimp contacts. Available only for multipole.
Fixed socket, nut fixing, with earthing tag, PEEK or POM outer shell
Reference
L maxi
M
øA
e
øB
S3
E maxi
S1
Model
Series
ERN
00
ERN
0S
ERN
1S
ERN
2S
ERN
3S
A
9
B
10.2
11 12.4
e
Dimensions (mm)
M7x0.5
M9x0.6
14 15.8 M12x1.0
18 19.2 M15x1.0
E
5.5
L
–
L1)
M
14.5 1.0
6.4 19.3 19.3 1.8
S1
6.3
S3
9
8.2 11
7.5 22.4 22.4 1.5 10.5 14
8.5 26.3 26.3 2.0 13.5 17
22 25.0 M18x1.0 11.5 29.8 29.8 2.0 16.5 22
P1 Panel cut-out (page 158)
Note: 1) unipole model
90
www.lemo.com
®
®
Watertight or vacuumtight models
These socket or coupler models allow the device on which they are fitted to reach a protection index of IP68 as per IEC
60529. They are fully compatible with plugs of the same series and are widely used for portable radios, military, laboratory
equipment, aviation, etc.
These models are identified by a letter «P» at the end of the reference.
Most of these models are also available in a vacuumtight version. Such models are identified by an additional letter «V» at
the end of the part number (certificate on request).
Epoxy resin is used to seal these models.
Technical Characteristics
Mechanical and Climatical
Characteristics
Endurance1)
Value
> 5000 cycles
Humidity
Characteristics
IEC 60512-5 test 9a
up to 95% at 60° C
Temperature range
Salt spray corrosion
Climatical category
Leakage rate
Standard
(He)2)
0S-1S
- 20° C/ + 100° C
2S-6S
- 20° C/+ 80° C
test4)
Maximum operating
pressure3)
Value
Standard
0S
60 bar
IEC 60512-7 test 14d
1S
60 bar
IEC 60512-7 test 14d
2S
40 bar
IEC 60512-7 test 14d
3S
30 bar
IEC 60512-7 test 14d
4S
15 bar
IEC 60512-7 test 14d
> 1000h
IEC 60512-6 test 11f
20/80/21
IEC 60068-1
5S
5 bar
IEC 60512-7 test 14d
IEC 60512-7 test 14b
6S
5 bar
IEC 60512-7 test 14d
<
10-7
mbar.l.s-1
Note: 1) see page 189, contact resistance after mating cycles. See page 185, mechanical endurance latching force.
2) only for vacuumtight models. Residual traces of grease used during (He) leak testing are on the o-ring. Please contact us for further details.
3) this value corresponds to the maximum allowed pressure difference for the assembled socket. 4) for chrome plated product (« C » material code).
HGP Fixed socket, nut fixing, watertight or vacuumtight
Reference
Dimensions (mm)
Model Series A B
L maxi
øA
M
e
øB
S3 S1
E maxi
e
E
L L1) M S1 S3
HGP
0S
18 15.8 M12x1.0 11.5 20.5 21.5 4.0 10.5 14
HGP
1S
20 19.2 M14x1.0 15.5 25.0 22.0 4.0 12.5 17
HGP
2S
20 21.5 M16x1.0 17.0 29.5 28.0 4.0 14.5 19
HGP
3S
28 27.0 M20x1.0 18.0 33.0 34.0 6.0 18.5 24
HGP
4S
34 34.0 M25x1.0 22.5 39.0 43.0 6.5 23.5 30
HGP
5S
45 40.0 M35x1.0 28.0 50.5 78.5 7.5 33.5 –
HGP
6S
58 54.0 M48x1.5 22.0 51.0 –
6.0 45.5 –
P3 Panel cut-out (page 158)
Note: 1) unipole model.
Note: The 5S and 6S series are delivered with a round nut.
HGW Fixed socket, nut fixing, with back washer, watertight or vacuumtight
L maxi
S3
M
Reference
Dimensions (mm)
E mini/maxi
øA
e
øB
Model Series A B
E
E
e
mini maxi
L M S3
HGW
0S
10 15 M9x0.6 2
3 20.5 1.2 11
HGW
1S
14 18 M12x1.0 2
4 25.0 1.5 14
P11 Panel cut-out (page 158)
Note: vacuumtight version is only available in the 0S series.
www.lemo.com
91
®
®
EWB Fixed socket, nut fixing, with two flats on the flange, watertight or vacuumtight
Reference
L maxi
øA
M
e
øB
S3 S1
S4
E maxi
HCP
Model
Series
EWB
0S
EWB
1S
EWB
2S
EWB
4S
A
B
Dimensions (mm)
e
E
L
18 15.8 M12x1.0 11.0 20.5
L1)
–
M
S1 S3 S4
4.0 10.5 14 14
20 19.2 M14x1.0 15.5 25.5 25.5 4.0 12.5 17 16
20 21.5 M16x1.0 17.0 28.0 26.5 4.0 14.5 19 16
34 34.0 M25x1.0 22.5 43.0
P3 Panel cut-out (page 158)
–
6.5 23.5 30 27
Note: 1) unipole model
Fixed socket, nut fixing, watertight or vacuumtight (back panel mounting)
L maxi
Reference
e
øB
øA
M
S1
E maxi
SWH Fixed coupler, nut fixing, watertight or vacuumtight
L
øA
e
øB
M
E maxi
Series
HCP
1S
HCP
2S
HCP
4S
A
B
e
E
L
M
P
18
20 M14x1.0
27
34 M25x1.0 15.5 41.0 4.5 20.0 23.5
20
8.6 25.5 3.5 12.0
S1
–
20 M16x1.0 12.5 29.0 3.5 16.5 14.5
P3 Panel cut-out (page 158)
P
S3
Model
Dimensions (mm)
S1
Note: the 2S and 4S series are delivered with a conical nut.
Reference
Model
Series
SWH
0S
SWH
1S
SWH
2S
SWH
3S
SWH
4S
SWH
5S
SWH
6S
A
B
Dimensions (mm)
e
E
L
M
S1
S3
14 13.8 M10x0.75 17
34
2.0
20 21.5 M16x1.00 25
44
4.0 15.0 19
17 15.8 M12x1.00 28
25 27.0 M20x1.00 30
34 34.0 M25x1.00 50
45 40.0 M35x1.00 58
58 54.0 M48x1.50 55
P4 Panel cut-out (page 158)
39
53
65
80
81
9.0 12
2.5 10.5 14
4.0 18.5 24
4.0 23.5 30
5.0 33.5
6.0 45.5
–
–
Note: The 5S and 6S series are delivered with a round nut.
Note: see page 114 for the available plug and contact configurations and
in order to ensure correct contact alignment.
92
www.lemo.com
E Series
®
®
E series connectors have been specifically designed for outdoor applications.
They include an inner sleeve and two seals to prevent penetration of solids or liquids into the housing formed by the plug,
free socket, fixed socket or coupler. All models of these series are watertight when mated and give a protection index of
IP 68 as per IEC 60529 standard (in mated condition) when correctly assembled to an appropriate cable (IP 66 otherwise).
– security of the Push-Pull latching system
– watertight connection (IP 68/IP 66)
– unipole types transmitting current up to 230 A
– polarization by stepped insert (half-moon)
and multipole types with up to 106 contacts
fitted with male and female contacts
– wide range of models satisfying most applications
– solder or print contacts (straight or elbow)
– 360° screening for full EMC shielding
– rugged housing for extreme working condition.
Metal housing models (page 95)
Straight plug
Straight plugs
FZP*
FFA, FFP*
Fixed plug
FFA
Fixed sockets
Free sockets
ERA
EEP
ERC
EEP
ERB*
EEP
PCA, PCP*
PCA
FAA
Elbow plug
FFA
FLM
PCA
Fixed socket
FFF
EHP*
PSA
Free coupler
FLA
Watertight or vacuumtight models (page 101)
Fixed sockets
HGP
www.lemo.com
Fixed coupler
EBR
SWH
RMA
Note: * Contact LEMO for details.
93
®
®
Part Numbering System
Plug
Free socket
F F A . 1 E . 3 0 4 . C L A C 3 5
P C A . 1 E . 3 0 4 . C L L C 3 5 Z
Variant: (page 121)
Cable ø: (page 119)
Collet type: (page 119)
Fixed socket
E R A . 1 E . 3 0 4 . C L L
Coupler
R M A . 1 E . 3 0 4 . C L L
Variant: (page 121)
Model: (page 95)
Contact: (page 112)
Series: (page 95)
Insulator: (page 112)
Insert configuration: (p. 103)
Housing: (page 112)
FFA.1E.304.CLAC35 = straight plug with cable collet, 1E series, multipole type with 4 contacts, outer shell in chrome-plated brass, PEEK
insulator, 2 male and 2 female solder contacts, C type collet for a 3.5 mm diameter cable.
PCA.1E.304.CLLC35Z = free socket with cable collet, 1E series, multipole type with 4 contacts, outer shell in chrome-plated brass, PEEK
insulator, 2 female and 2 male solder contacts, C type collet for a 3.5 mm diameter cable and collet nut for fitting a bend relief.
ERA.1E.304.CLL = fixed socket, nut fixing, 1E series, multipole type with 4 contacts, outer shell in chrome-plated brass, PEEK insulator,
2 female and 2 male solder contacts.
RMA.1E.304.CLL = straight coupler, 1E series, multipole type with 4 contacts, outer shell in chrome-plated brass, PEEK insulator, 2
female and 2 male contacts each end.
Part Section Showing Internal Components
Straight plug
Fixed socket
1
2
3
4
5
6
7
8
outer shell
earthing crown
retaining ring
hexagonal nut
insulator
male contact
female contact
o-ring
5
2
3
8
4
1
8
7
6
9
8
2
3
7
6
1
4
10
12
11
5
1
2
3
4
5
6
7
8
9
10
11
12
outer shell
latch sleeve
inner shell
retaining ring
collet nut
centre-piece
insulator
male contact
female contact
earthing cone
collet + washer 1)
gasket
Note: 1) depending on models.
94
www.lemo.com
®
®
Metal housing models
Technical Characteristics
Electrical
Mechanical and Climatical
Characteristics
Endurance1)
Value
> 5000 cycles
Humidity
Temperature
Standard
IEC 60512-5 test 9a
up to 95% at 60° C
range2)
- 55° C, + 200° C
Resistance to vibrations
10-2000 Hz, 15g IEC 60512-4 test 6d
Shock resistance
100 g, 6 ms
IEC 60512-4 test 6c
Salt spray corrosion test4)
> 1000h
IEC 60512-6 test 11f
Protection index (mated)3)
IP 68/IP 66
IEC 60529
Climatical category
50/175/21
IEC 60068-1
Characteristics
Shielding
efficiency
Value
Standard
at 10 MHz
> 95 dB
IEC 60169-1-3
at 1 GHz
> 80 dB
IEC 60169-1-3
Note: the various tests have been carried out with FFA and ERA connector
pairs, with chrome-plated brass shell, PEEK insulator and silicone O-ring.
Detailed electrical characteristics, as well as materials and treatment are
presented in the chapter Technical Characteristics on page 182.
1) see page 189, contact resistance after mating cycles. See page 185,
mechanical endurance latching force.
2) minimum operating temperature is -20°C for sockets fitted with an FPM
(Viton®) O-ring.
3) IP68 achieved providing that the cable is perfectly circular and that
assembly process ensures a high integrity seal.
4) for chrome plated product (« C » material code).
FFA Straight plug, cable collet
Reference
Dimensions (mm)
Model Series A
~L
øA
~M
S2
L
M S2
FFA
0E
11 34 23.0 8
FFA
1E
13 42 28.0 9
FFA
2E
16 52 36.0 12
FFA
3E
19 61 41.0 15
FFA
4E
25 71 50.5 19
FFA
5E
38 92 67.0 32
FGG1) 6E
47 118 89.0 38
Note: 1) with key (G)
M1 Cable assembly (pages 179 to 181)
FFA Straight plug with oversize cable collet 1)
Reference
Dimensions (mm)
Model Series A
~L
øB
øA
~M
S2
www.lemo.com
S1
B
L
M S1 S2
FFA
1E
13 14.5 55 41 12 12
FFA
2E
16 17.0 65 49 15 15
FFA
3E
19 22.0 80 60 19 19
FFA
4E
25 36.0 118 84 30 32
M2 Cable assembly (pages 179 and 181)
Note: 1) correspond to K type of collet, the fitting of oversize collets onto
this model allows them to be fitted to the cables that can be accommodated
by the next housing size up (see page 119).
95
®
FFA
®
Straight plug, cable collet and nut for fitting a bend relief 1)
Reference
~L
øA
~M
S2
Model
Series
FFA
0E
FFA
1E
FFA
2E
FFA
3E
FFA
4E
Dimensions (mm)
A
L
M
S2
28.0
9
11
34
23.0
16
52
36.0
12
50.5
19
13
19
25
42
60
71
40.0
7
15
M1 Cable assembly (pages 179 and 180)
FFF
Note: 1) to order, add a «Z» at the end of the reference.
The bend relief must be ordered separately (see page 145).
Straight plug non-latching cable collet
~L
Reference
øA
~M
S2
FAA
øA
M
e
øB
FLM
FFF
0E
FFF
1E
Reference
L maxi
A
11
13
L
34
42
M
S2
28
9
23
8
Model
Series
FAA
0E
FAA
1E
FAA
2E
FAA
3E
A
B
e
Dimensions (mm)
E
L
L1)
M
S1
S3
18 19.2 M14x1.0 3.5 19.5 19.5 13.0 12.5 17
20 21.5 M16x1.0 3.5 23.0 23.0 16.0 14.5 19
25 27.0 M20x1.0 4.0 27.0 27.0 18.0 18.5 24
31 34.0 M24x1.0 4.5 32.5 32.5 22.5 22.5 30
P1 Panel cut-out (page 159)
S1
E maxi
Series
M1 Cable assembly (pages 179 and 180)
Fixed plug non-latching, nut fixing
S3
Model
Dimensions (mm)
Note: 1) unipole model
Elbow (90°) plug, cable collet
~L
S1
~H
øA
~M
S3
S2
D
96
Reference
Model
Series
FLM
0E
FLM
1E
FLM
2E
A
D
Dimensions (mm)
H
L
M
S1
S2
S3
28
11
9
10
11
7.3
25
36
25
16
10.2
40
51
35
13
8.7
33
42
M3 Cable assembly (pages 179 and 180)
9
14
8
12
8
13
www.lemo.com
®
®
FLA Elbow (90°) plug, cable collet
~L
S1
øA
~M
Dimensions (mm)
Reference
H
Model Series A
S3
S2
D
D
H
L
M S1 S2 S3
FLA
3E
21.0 11.5 47
60 40.0 18
15
16
FLA
4E
27.5 15.5 57
72 51.5 24
19
22
M3 Cable assembly (pages 179 and 180)
ERA Fixed socket, nut fixing
Reference
Dimensions (mm)
Model Series A B
L maxi
øA
M
e
øB
S3
E maxi
S1
e
E L L1) M S1 S3
ERA
0E
18 19.2 M14x1.0 5.5 19.5 20.5 4.0 12.5 17
ERA
1E
20 21.5 M16x1.0 9.0 24.0 25.3 4.5 14.5 19
ERA
2E
25 27.0 M20x1.0 9.0 28.5 30.0 5.0 18.5 24
ERA
3E
31 34.0 M24x1.0 11.0 34.0 35.0 6.0 22.5 30
ERA
4E
37 40.5 M30x1.0 9.0 36.0 38.0 6.5 28.5 36
ERA
5E
55 54.0 M45x1.5 10.0 44.5 78.0 9.0 42.5 –
EGG2) 6E
65 65.0 M55x2.0 10.5 48.5 – 10.0 52.0 –
P1 Panel cut-out (page 159)
Note: 1) unipole model.
2) with key (G).
Note: The 5E and 6E series are delivered with a round nut.
ERC Fixed socket, nut fixing with slot in the flange
L maxi
S3
M
Dimensions (mm)
øA
e
øB
F
Reference
E maxi
S1
A
B e E
F
L
L1) M S1 S3
Model Series
ERC
0E
18 19.2 M14x1.0 5.5 1.5 19.5 20.5 4.0 12.5 17
ERC
3E
31 34.0 M24x1.0 11.0 3.0 34.0 35.0 6.0 22.5 30
ERC
4E
37 40.5 M30x1.0 9.0 3.0 36.0 38.0 6.5 28.5 36
P1 Panel cut-out (page 159)
Note: 1) unipole model.
www.lemo.com
97
®
EEP
®
Fixed socket, nut fixing (back panel mounting)
L maxi
P
e
øB
øA
M
S1
EEP
0E
EEP
1E
EEP
2E
EEP
3E
A
B
e
E
L
L1)
M
18
18 M14x1.0 3.5 19.5 20.5 3.5
25
25 M20x1.0 6.5 28.5 30.0 3.5
20
30
P
7
S1
12.5
20 M16x1.0 6.5 24.0 25.3 3.5
10 14.5
31 M24x1.0 7.5 34.0 35.0 4.5
12 22.5
10 18.5
Note: 1) unipole model
Fixed socket, nut fixing, with straight contact for printed circuit (back panel mounting)
Reference
N
P
e
øB
øA
M
S1
Model
Series
EEP
0E
EEP
1E
EEP
2E
EEP
3E
A
B
Dimensions (mm)
e
E
M
N
P
18
18 M14x1.0 3.5
3.5 16.0
25
25 M20x1.0 6.5
3.5 24.0 10 18.5
20
30
20 M16x1.0 6.5
31 M24x1.0 7.5
P1 Panel cut-out (page 159)
7
S1
12.5
3.5 21.5 10 14.5
4.5 29.5 12 22.5
P21 PCB drilling pattern (page 166)
Note: The 3E series is delivered with a conical nut.
E maxi
Note: this contact type is available for all Ell socket models.
See page 167 for table of available types.
Length «L» depends on the number of contacts, see PCB drilling pattern
on page 167.
Fixed socket, nut fixing, with elbow (90°) contacts for printed circuit (back panel mounting)
L
N
Reference
P
E maxi
2
øA
e
M
20 mini
øB
S1
98
Series
Note: the 3E series is delivered with a conical nut.
L
EEP
Model
Dimensions (mm)
P1 Panel cut-out (page 159)
E maxi
EEP
Reference
Model
Series
EEP
1E
EEP
2E
A
20
25
B
Dimensions (mm)
e
E
20 M16x1.0 6.5
25 M20x1.0 6.5
P1 Panel cut-out (page 159)
M
N
P
S1
3.5 21.5 10 14.5
3.5 24.0 10 18.5
P24 PCB drilling pattern (page 168)
Note: this contact type is available for all back panel mounting socket
types. See page 168 for available types.
Length «L» depends on the number of contacts, see PCB drilling pattern
on page 168.
www.lemo.com
®
PCA
Free socket, cable collet
Reference
øA
~L
S2
Model
Series
PCA
0E
PCA
1E
PCA
2E
PCA
3E
PCA
4E
PCA
5E
PHG1)
PCA
6E
Reference
~L
A
L
S2
13
34.0
19
54.0
12
75.5
19
15
23
29
42
52
8
45.0
9
65.0
15
95.0
32
125.0
38
Note: 1) with key (G)
Model
Series
PCA
1E
PCA
2E
PCA
3E
PCA
4E
A
Dimensions (mm)
B
L
S1
S2
67.0
15
15
15
14.5
58.0
23
22.0
84.0
19
29
17.0
36.0 109.0
M2 Cable assembly (page 181)
øA
øB
PCA
Dimensions (mm)
M1 Cable assembly (pages 179 to 181)
Free socket with oversize cable collet 1)
S2
®
12
19
30
12
19
32
Note: 1) correspond to K type of collet, the fitting of oversize collets onto
this model allows them to be fitted to the cables that can be accommodated
by the next housing size up (see page 119).
S1
Free socket, cable collet and nut for fitting a bend relief 1)
Reference
øA
~L
Model
Series
PCA
0E
PCA
1E
PCA
2E
PCA
3E
PCA
4E
S2
Dimensions (mm)
A
L
S2
45.0
9
13
34.0
19
54.0
12
75.5
19
15
23
29
64.0
7
15
M1 Cable assembly (pages 179 and 180)
Note: 1) to order, add a «Z» at the end of the reference.
The bend relief must be ordered separately (see page 145).
www.lemo.com
99
®
PSA
®
Fixed socket, nut fixing, cable collet
Reference
L maxi
øA
M
e
øB
S3
Model
Series
PSA
0E
PSA
1E
PSA
2E
PSA
3E
PSA
4E
PSA
5E
PKG1)
S2
E maxi
S1
6E
A
B
e
Dimensions (mm)
E
L
M
S1
S2 S3
18 19.2 M14x1.0
5.5
34.0
4.0 12.5
8
17
25 27.0 M20x1.0
9.0
54.0
5.0 18.5 12
24
20 21.5 M16x1.0
9.0
31 34.0 M24x1.0 11.0
37 40.5 M30x1.0
9.0
51 54.0 M45x1.5 10.0
45.0
65.0
75.5
95.0
4.5 14.5
6.0 22.5 15
6.5 28.5 19
9.0
65 65.0 M55x2.0 10.5 125.0 10.0
P1 Panel cut-out (page 159)
9
–
–
32
38
19
30
36
54
–
M1 Cable assembly (pages 179 to 181)
Note: The 5E and 6E series are delivered with a round nut.
Note: 1) with key (G).
RMA Free coupler
Reference
øA
L maxi
Model
Series
RMA
0E
RMA
1E
RMA
2E
RMA
3E
RMA
4E
RMA
5E
Dim. (mm)
A
14
16
20
25
30
44
L
30
40
44
54
57
67
Note: see page 114 for the available plug and contact configurations and
in order to ensure correct contact alignment.
100
www.lemo.com
®
®
Watertight or vacuumtight models
These socket or coupler models allow the device on which they are fitted to reach a protection index of IP 68 as per IEC 60529.
They are fully compatible with plugs of the same series and are widely used for portable radios, military, laboratory equipment,
aviation, etc.
These models are identified by a letter «P» at the end of the reference.
Most of these models are also available in a vacuumtight version. Such models are identified by an additional letter «V» at the
end of the part number (certificate on request).
Epoxy resin is used to seal these models.
Technical Characteristics
Mechanical and Climatical
Characteristics
Value
Endurance1)
> 5000 cycles
Humidity
Characteristics
IEC 60512-5 test 9a
up to 95% at 60° C
Temperature range
0E-1E
- 20° C, + 100° C
2E-6E
- 20° C, + 80° C
Salt spray corrosion test
Climatical category
Leakage rate
Standard
(He)2)
4)
Maximum operating
pressure3)
Value
Standard
0E
60 bar
IEC 60512-7 test 14d
1E
60 bar
IEC 60512-7 test 14d
2E
40 bar
IEC 60512-7 test 14d
3E
30 bar
IEC 60512-7 test 14d
4E
15 bar
IEC 60512-7 test 14d
> 1000h
IEC 60512-6 test 11f
20/80/21
IEC 60068-1
5E
5 bar
IEC 60512-7 test 14d
IEC 60512-7 test 14b
6E
5 bar
IEC 60512-7 test 14d
<
10-7
mbar.l.s-1
Note: 1) see page 189, contact resistance after mating cycles. See page 185, mechanical endurance latching force.
2) only for vacuumtight models. Residual traces of grease used during (He) leak testing are on the o-ring. Please contact us for further details.
3) this value corresponds to the maximum allowed pressure difference for the assembled socket. 4) for chrome plated product (« C » material code).
HGP Fixed socket, nut fixing, watertight or vacuumtight
Reference
Dimensions (mm)
Model Series A B
L maxi
M
øA
e
øB
S3
E maxi
S1
e
E
L L1) M S1 S3
HGP
0E
18 19.2 M14x1.0 5.5 23.5 22.0 4.0 12.5 17
HGP
1E
20 21.5 M16x1.0 9.0 29.5 28.0 4.5 14.5 19
HGP
2E
25 27.0 M20x1.0 10.5 32.5 28.0 5.0 18.5 24
HGP
3E
31 34.0 M24x1.0 15.5 39.5 38.5 6.0 22.5 30
HGP
4E
37 40.5 M30x1.0 17.5 43.0 44.0 6.5 28.5 36
HGP
5E
55 54.0 M45x1.5 20.0 52.0 76.0 9.0 42.5 –
HGP2) 6E
65 65.0 M55x2.0 20.5 52.0 – 10.0 52.0 –
P1 Panel cut-out (page 159)
Note: 1) unipole model.
2) with key (G).
Note: The 5E and 6E series are delivered with a round nut.
www.lemo.com
101
®
EBR
®
Fixed socket with round flange, watertight, protruding shell and screw fixing
N
~L
H1
H2
øA
øB
~M
Reference
Model
Series
EBR
2E
A
28
B
15
P6 Panel cut-out (page 159)
øC
C
Dimensions (mm)
H1
H2
L
2.8 11.8 20.4 32.5
L1)
28
M
19
N
25
Note: 1) unipole model.
SWH Fixed coupler, nut fixing, watertight or vacuumtight
L
M
øA
e
øB
S3
Note: This model is only available in a watertight version.
Reference
Model
Series
SWH
0E
SWH
1E
SWH
2E
SWH
3E
SWH
4E
SWH
5E
SWH1)
E maxi
S1
6E
A
B
Dimensions (mm)
e
E
L
M
S1
S3
18 19.2 M14x1.0 22.5 36.0
4.0 12.5 17
25 27.0 M20x1.0 28.0 52.4
5.0 18.5 24
20 21.5 M16x1.0 30.5 47.0
31 34.0 M24x1.0 33.0 64.2
37 40.5 M30x1.0 44.5 70.0
55 54.0 M45x1.5 47.0 81.0
4.5 14.5 19
6.0 22.5 30
6.5 28.5 36
9.0 42.5
65 65.0 M55x2.0 12.0 76.0 10.0
P1 Panel cut-out (page 159)
–
–
–
Note: 1) with key (G).
Note: The 5E and 6E series are delivered with a round nut.
Note: See page 114 for the available plug and contact configurations
and in order to ensure correct contact alignment.
102
www.lemo.com
®
®
Rated current (A)1)
Test voltage (kV dc)1)
min.
max.
Solder (max.)
Print (elbow)
Crimp
Solder
Test voltage (kV rms)1)
AWG
Crimp
Contact ø (mm)
Watertight
Standard
Reference
1
Contact
type
Series
Print (straight)
Solder contacts
Number of LV contacts
Unipole
Insert configuration (S and E series)
113
00
–
1.3
l2)
l
–
–
20
26
18
0.8
1.2
8
116
0S
0E
1.6
l2)
–
–
–
18
–
–
1.5
2.1
12
120
1S
1E
2.0
l2)
–
–
–
16
–
–
1.9
2.7
18
1S
1E
2E
3.0
3.0
l
–
–
–
12
–
–
–
1.5
2.1
2.1
3.0
25
30
2S
2E
4.0
l
–
–
–
10
–
–
1.7
2.4
40
4S
–
4.0
l
–
–
–
10
–
–
3.0
4.2
46
1.7
2.4
65
130
140
160
112
2S
3S
l
3E
4.0
3S
3E
4E
6.0
6.0
l
5S
5E
12.0
l
4S
l
l
–
–
–
–
–
–
12
10
–
–
–
2.3
3.3
43
–
–
–
8
–
–
–
2.7
3.9
70
–
–
–
0
–
–
1.5
2.1
230
–
–
–
8
–
Note: 1) see calculation method, caution and suggested standard on page 190. 2) also available with inversed contacts: plug = female, socket = male.
l First choice alternative
www.lemo.com
l Special order alternative
103
®
®
Multipole
Contact
type
Print (straight)
l
l 22 32 20 1.1 1.6 103)
1S
1E
1.3 l
l
l
l 20 26 18 1.2 1.8 153)
1
1
302
2S
2E
1.6 l
l
l
l 18 22 14 1.7 2.4 204)
2
2
3S
3E
2.0 l
–
l
– 16 –
–
3.0 4.2 23
4S
4E
4.0 l
–
l
– 10 –
–
2.1 3.0 35
5S
5E
6.0 l
–
–
– 8 –
–
3.7 5.2 50
3
0S
0E
0.7 l
l
l
l 26 32 22 1.0 1.5 73)
1S
1E
0.9 l
l
l
l 22 32 20 1.2 1.8 103)
2
1
1
3
2
3
303
2S
2E
1.3 l
l
l
l 20 26 18 1.5 2.1 154)
3S
3E
2.0 l
–
l
– 16 –
–
1.5 2.1 20
4S
4E
3.0 l
–
l
– 12 –
–
2.1 3.0 25
5E
1x6.0
2x4.0
l
–
–
8
– –
10
–
50
3.7 5.2
35
6.0 l
–
–
– 8 –
–
3.0 4.2 50
5S
max.
Crimp
l
min.
Solder
0.9 l
Solder (max.)
Watertight
0E
Print (elbow)
Standard
0S
Reference
2
Contact ø (mm)
Crimp
Crimp contacts
Rated current (A)1)
AWG
Test voltage (kV dc)1) 2)
Series
Test voltage (kV rms)1) 2)
Number of LV contacts
Solder contacts
3
1
1
2
3
3
2
4
2
1
1
2
3
4
4
3
303
– 6E
0S
0E
0.7 l
l
l
l 26 32 22 1.0 1.5 73)
1S
1E
0.9 l
l
l
l 22 32 20 1.2 1.8 103)
2S
2E
1.3 l
l
l
l 20 26 18 1.7 2.4 154)
304 3S
3E
2.0 l
–
l
– 16 –
–
1.5 2.1 18
4S
4E
3.0 l
–
l
– 12 –
–
2.1 3.0 22
5S
5E
4.0 l
–
–
– 10 –
–
3.7 5.2 35
6S
–
8.0 l
–
–
– 4 –
–
3.0 4.2 60
8.0 l
–
–
– 4 –
–
3.0 4.2 60
4
2
1
1
2
3
4
4
3
304
– 6E
Note: 1) see calculation method, caution and suggested standard on page 190. 2) lowest measured value; contact to contact or contact to shell.
3) rated current = 6A for socket with elbow (90°) contacts for printed circuit. 4) rated current = 12A for socket with elbow (90°) contacts for printed circuit.
l First choice alternative
104
Special order alternative
www.lemo.com
®
®
Multipole
Contact
type
2
2
1
1
4
3E
2x2.0
l
–
l
3x1.3
4S
4E
5S
2
2
1
4
4
6
6
5
4
2
5E
1S
1E
0.7 l
l
l
l 26 32 22 1.2 1.7 73)
2S
2E
1.3 l
l4)
l
l 20 26 18 1.5 2.1 12
306 3S
3E
1.3 l
–
l
– 20 –
–
2.1 3.0 14
4S
4E
2.0 l
–
l
– 16 –
–
2.1 3.0 16
5S
5E
3.0 l
–
–
– 12 –
–
3.0 4.2 25
2S
2E
3x1.3
4x0.9 l
l
l
20 26 18
123)
l
0.8
1.2 93)
22 32 20
307 3S
3E
1.3 l
–
l
– 20 –
–
1.0 1.5 12
4S
4E
3x2.0
4x1.3 l
–
l
16
– –
20
–
16
2.1
3.0 13
2S
2E
0.9 l
l
l
l 22 32 20 0.8 1.2 93)
3S
3E
1.3 l
–
l
l 20 –
–
1.0 1.5 10
4S
4E
1.3 l
–
l
– 20 –
–
2.7 3.9 13
5S
5E
3.0 l
–
–
– 12 –
–
2.1 3.0 22
309 4S
4E
1.3 l
–
l
– 20 –
–
2.1 3.0 12
2S
2E
0.9 l
l
l
l 22 32 20 0.8 1.2 73)
3S
3E
1.3 l
–
l
l 20 – –
5
3
2
1
5
4
1
5
7
7
6
6
8
3
2
9
3
4
8
2
6
4
5
3
3
6
9
9
7
3
2
1
8
1
9
8
7
–
–
7
8
2
–
4
5
8
308
5
6
1
9
10
6
7
2
1
7
4
7
5
10
1
8
5
6
3
2
1
4
18
1.5 2.1 14
22
2.1
3.0 16
35
3.0
4.2 25
2x3.0
l
–
l
3x2.0
2x4.0
l
–
–
3x3.0
7
3
l 20 26 18 1.5 2.1 134)
16
– –
20
12
– –
16
10
– –
12
3
1
l
max.
305 3S
l
min.
1.3 l
6
3
Solder (max.)
2E
5
5
Print (elbow)
2S
3
4
Print (straight)
2x0.9
22 20
103)
l
l l l 32
1.5
2.1 73)
3x0.7
26
22
Crimp
Watertight
1E
Solder
Standard
Reference
1S
5
3
Contact ø (mm)
Crimp
Crimp contacts
Rated current (A)1)
AWG
Test voltage (kV dc)1) 2)
Series
Test voltage (kV rms)1) 2)
Number of LV contacts
Solder contacts
4
10
5
6
310
1.0 1.5
9
Note: 1) see calculation method, caution and suggested standard on page 190. 2) lowest measured value; contact to contact or contact to shell.
3) rated current = 6A for socket with elbow (90°) contacts for printed circuit. 4) only for FFL model.
l First choice alternative
www.lemo.com
Special order alternative
105
®
®
Multipole
10
7
12
10
9
8
2
9
1
6
10
3
7
11
12
12
3
4
2
11
12
1
11
1
3
l
– 20 –
–
2.1 3.0 11
5S
5E
2.0 l
–
–
– 16 –
–
2.1 3.0 18
312 3S
3E
0.9 l
–
l
l 22 –
–
1.5 2.1
8
4S
4E
1.3 l
–
l
– 20 –
–
2.1 3.0
9
–
4.0 l
–
–
– 10 –
–
2.1 3.0 22
5.0 l
–
–
– 8 –
–
2.1 3.0 22
12
4
5
12
6
14
7
3
7
11
14
3
13
8
10
3
12
13
7
11
1
9
3
1
4
8
12
10 11
13
9
8
4
5
12
7
6
1
3
12
14
4
8
312 5S
5E
2.0 l
–
–
– 16 –
–
2.1 3.0 18
313 3S
3E
0.9 l
–
l
l 22 –
–
1.5 2.1
8
313 4S
–
1.3 l
–
l
– 20 –
–
2.1 3.0
9
314 3S
3E
0.9 l
–
l
l 22 –
–
1.5 2.1
7
9
1
2
1
– 6E
8
4
8
2
11 10
6
11
4
8
312 6S
5
7
1
13
4
Rated current (A)1)
–
1
11
7
11
8
12
12
8
6
7
2
7
10
12
3
3
4
5
10
2
13
3
9
6
9
6
10
9
4
5
1
10
8
12
1
2
11
12
7
7
8
3
7
2
5
6
6
310
max.
Print (straight)
1.3 l
5
min.
Crimp
4E
4
1
Solder (max.)
Solder
1
6
3
2
2
Print (elbow)
Watertight
3
Contact ø (mm)
Standard
4S
Reference
4
5
Test voltage (kV dc)1) 2)
AWG
Crimp
Crimp contacts
10
13
Contact
type
Series
Test voltage (kV rms)1) 2)
Number of LV contacts
Solder contacts
7
11
Note: 1) see calculation method, caution and suggested standard on page 190. 2) lowest measured value; contact to contact or contact to shell.
l First choice alternative
106
Special order alternative
www.lemo.com
®
®
Multipole
Contact
type
13
14
2
2
1.3 l
–
l
– 20 –
–
2.1 3.0
4
5
13
9
4
1
6
1
8
9
314 5S
5E
2x3.0
12x2.0 l
–
–
12
– –
16
–
20
1.8
2.4 15
3S
3E
0.9 l
–
l
l 22 –
–
1.0 1.5
7
4S
4E
0.9 l
–
l
– 22 –
–
2.1 3.0
7
11
5
4
5
316 5S
5E
2.0 l
–
–
– 16 –
–
1.8 2.4 15
– 6E
3.0 l
–
–
– 12 –
–
1.5 2.1 14
4
9
4
2
2
13
1
6
15
12
16
9
3
18
7
5
6
4
11
12
3
3
1
16
15
13
14
5
4
6
8
9
18
16
14
13
12
3S
3E
0.9 l
–
l
l 22 –
–
1.0 1.5
6
4S
4E
0.9 l
–
l
– 22 –
–
2.1 3.0
7
318 5S
5E
2x3.0
16x1.6 l
–
–
12
– –
18
–
18
1.8
2.4 11
7
17
1
15
318
18
2
2
18
10
14
15
17
9
4
10
15
8
9
5
316
6
7
1
5
10
5
13
14
15
8
1
18
12
16
7
4
4
11
10
8
14
9
10
9
1
16
15
6
9
1
9
13
8
3
2
10
14
16
11
2
11
12
18
12
11
10
4
5
7
15
8
Standard
5
14
13
1
316
16
3
3
14
8
12
13
13
6
9
10
1
5
9
16
7
8
1
12
16
12
11
10
4
8
7
14
12
9
5
13
14
16
6
8
3
5
7
2
2
13
7
14
3
6
max.
4E
4
12
9
8
14
3
11
10
10
7
16
1
1
min.
Print (straight)
11
Solder (max.)
Crimp
6
12
Print (elbow)
Solder
3
4
5
Watertight
314 4S
Reference
14
Contact ø (mm)
Crimp
Crimp contacts
Rated current (A)1)
AWG
Test voltage (kV dc)1) 2)
Series
Test voltage (kV rms)1) 2)
Number of LV contacts
Solder contacts
10
11
Note: 1) see calculation method, caution and suggested standard on page 190. 2) lowest measured value; contact to contact or contact to shell.
l First choice alternative
www.lemo.com
Special order alternative
107
®
®
Multipole
6
10
16
20
3
10
1
20
11
20
4
20
16
19
11
12
14
13
1
5
18
11
19
16
4
5
6
320 4S
4E
0.9 l
–
l
– 22 – –
2.1 3.0
320 5S
5E
1.6 l
–
–
– 18 –
–
1.8 2.4 11
320 6S
–
3.0 l
–
–
– 12 –
–
1.5 2.1 14
8
14
12
13
1
3.0 l
–
–
– 12 –
–
1.5 2.1 14
–
2.1 3.0
5
10
15
16
19
4
3
2
2
5
6
17
16
1
7
15
18
10
1
20
22
7
8
9
3
12
16
22
21
5
6
4
18
19
11
12
13
3
16
14
15
12
1
2
4
22
5
6
18
19
14
21
13
12
322 4S
4E
0.9 l
–
l
– 22 –
322 5S
5E
2x3.0
20x1.6 l
–
–
12
– – –
18
7
8
20
22
15
11
7
20
17
16
– 6E
6
16
21
320
9
10
11
1
2
1
8
19
12
17
2
22
21
7
3
20
10
3
7
17
17
20
13
13
12
2
6
11
11
14
14
20
19
7
11
18
22
9
10
11
1
9
1.2 1.8 16
7
6
3
17
8
–
20
15
16
7
6
19
20
20
10
18
2
15
5
4
16
2
6
20
20
15
10
Rated current (A)1)
– 10 –
17
17
1
15
Test voltage (kV dc)1) 2)
–
max.
–
min.
4.0 l
Solder (max.)
–
5
15
3
1
3
11
2
2
18
10
1
16
3
17
9
6
16
18
5
6
7
8
13
18
4
6
9
16
17
4
15
17
5
14
17
5
2
10
14
18
1
3
6
Print (elbow)
Print (straight)
3
Watertight
Crimp
1
Standard
318 6S
Reference
2
5
9
Contact ø (mm)
Crimp
Crimp contacts
13
20
AWG
Solder
18
Contact
type
Series
Test voltage (kV rms)1) 2)
Number of LV contacts
Solder contacts
9
10
16
1.8
2.4 9
11
Note: 1) see calculation method, caution and suggested standard on page 190. 2) lowest measured value; contact to contact or contact to shell.
l First choice alternative
108
Special order alternative
www.lemo.com
®
®
Multipole
Contact
type
Print (straight)
5
6
7
18
22
4
19
9
21
22
11
30
1
16
24
10
12
23
4E
0.9 l
–
l
– 22 –
–
2.1 3.0
7
324 5S
5E
1.6 l
–
–
– 18 –
–
2.7 3.9
9
–
3.0 l
–
–
– 12 –
–
1.2 1.8 12
3.0 l
–
–
– 12 –
–
1.2 1.8 12
1
4
10
21
16
26
22
30
4
9
9
28
21
22
24
25
12
12
25
19
19
26
36
3
1
4
25
29
19
19
29
25
33
30
36
34
6E
2.0 l
–
–
– 16 –
–
2.1 3.0 10
– 6E
2.0 l
–
–
– 16 –
–
1.5 2.1 10
332
336 5S
5E
1.3 l
–
–
– 20 –
–
1.8 2.4
7
336 6S
–
2.0 l
–
–
– 16 –
–
1.5 2.1
8
7
12
24
330 6S
3
4
8
13
8
36
32
13
1.8 2.4
11
25
8
–
31
1
7
5
26
32
12
– 20 –
32
18
18
–
28
1
6
6
31
16
17
29
1
–
4
8
29
5
1.3 l
30
5
18
36
26
25
32
15
16
9
5E
4
5
10
1
5
330 5S
30
27
17
11
22
1
8
24
36
15
28
27
– 6E
8
1
5
16
2
23
1
324
11
12
29
9
32
13
1
29
15
9
10
22
16
23
30
8
21
23
3
28
7
9
9
16
6
19
24
3
6S
20
14
22
30
16
14
2
8
5
4
15
15
24
18
1
12
21
17
15
13
22
2
17
7
17
3
2
3
13
18
3
18
20
8
8
8
13
24
1
4
max.
Crimp
17
21
24
4
min.
Solder
12
1
Solder (max.)
Watertight
3
7
Print (elbow)
Standard
4S
Reference
24
Contact ø (mm)
Crimp
Crimp contacts
Rated current (A)1)
AWG
Test voltage (kV dc)1) 2)
Series
Test voltage (kV rms)1) 2)
Number of LV contacts
Solder contacts
18
24
30
33
34
36
Note: 1) see calculation method, caution and suggested standard on page 190. 2) lowest measured value; contact to contact or contact to shell.
l First choice alternative
www.lemo.com
Special order alternative
109
®
®
Multipole
Contact
type
30
36
21
31
40
1
13
34
40
35
21
21
1
7
14
2
8
22
30
23
37
16
3
9
1
4
30
33
1
39
31
47
40
1
30
39
47
48
2
40
32
41
48
55
13
5
31
40
48
49
–
1.5 2.1
8
max.
– 16 –
min.
–
Solder (max.)
–
Print (elbow)
2.0 l
Watertight
– 6E
5E
1.3 l
–
–
– 20 –
–
1.2 1.8
6
5S
5E
1.3 l
–
–
– 20 –
–
1.2 1.8
6
6S
6E
2.0 l
–
–
– 16 –
–
1.5 2.1
7
360 6S
6E
1.6 l
–
–
– 18 –
–
1.5 2.1
5
362
6E
1.6 l
–
–
– 18 –
–
1.5 2.1
5
364 6S
6E
1.3 l
–
–
– 20 –
–
1.2 1.8
4
348
55
56
61
62
1
6
6
14
22
42
33
51
43
59
52
60
1
5
13
22
14
23
32
64
22
41
62
64
7
14
32
56
1.2 1.8
7
23
49
61
1
8
15
23
–
60
2
31
– 20 –
54
55
15
–
21
40
8
–
13
31
55
22
1.3 l
6
22
48
7
39
45
14
22
5E
5S
344 5S
16
48
7
14
54
9
33
40
7
14
3
32
1
13
21
60
1
4
46
30
4
1.5
2.1
22
43
44
24
46
6
22
25
40
48
–
14
37
10
25
45
7
17
17
39
1
2
340
34
31
10
32
62
8
40
38
24
60
28
35
38
44
12
23
31
43
48
15
15
6
20
29
29
20
– –
8
– 6E
32
1
7
13
336
31
34
7
28
30
36
33
6
12
44
35
33
20
–
20
21
34
32
–
11
12
35
30x1.3
6x5.0 l
5
6
12
Print (straight)
1
6
Crimp
1
Solder
5
11
20
Standard
Reference
36
Contact ø (mm)
Crimp
Crimp contacts
Rated current (A)1)
AWG
Test voltage (kV dc)1) 2)
Series
Test voltage (kV rms)1) 2)
Number of LV contacts
Solder contacts
32
23
33
42
43
51
52
59
60
64
Note: 1) see calculation method, caution and suggested standard on page 190. 2) lowest measured value; contact to contact or contact to shell.
l First choice alternative
110
Special order alternative
www.lemo.com
®
®
Multipole
Contact
type
18
46
37
55
47
72
106
46
2
9
1
56
18
18
70
80
37
48
60
60
71
89
81
97
104
11
106
105
3
1
4
53
70
89
76
66
77
87
96
104
4
1
3
11
2
0.9 l
–
–
– 22 –
–
0.8 1.2
2
max.
0.8 1.2
min.
–
Solder (max.)
– 22 –
Print (elbow)
–
Watertight
–
20
77
86
54
0.9 l
106
30
54
– 6E
104
21
42
106
97
31
42
65
106
47
59
80
12
31
4
17
36
90
21
86
9
81
12
1.2 1.8
26
105
30
2
98
41
95
103
1
10
71
90
98
–
72
27
27
37
48
– 20 –
70
3
10
–
372 6S
63
64
3
17
20
55
71
26
106
36
47
71
36
47
59
–
26
37
56
1.3 l
17
27
64
6E
9
18
27
63
2
10
10
70
1
3
3
Print (straight)
1
Crimp
2
Solder
9
17
26
36
Standard
Reference
72
Contact ø (mm)
Crimp
Crimp contacts
Rated current (A)1)
AWG
Test voltage (kV dc)1) 2)
Series
Test voltage (kV rms)1) 2)
Number of LV contacts
Solder contacts
41
53
65
66
76
87
96
106 6S
–
95
103
104
106
Note: 1) see calculation method, caution and suggested standard on page 190. 2) lowest measured value; contact to contact or contact to shell.
l First choice alternative
www.lemo.com
Special order alternative
111
®
®
Housings (S and E series)
Outer shell and collet nut
Ref.
Material
Surf. treatment
Brass
gold-plated
Brass
C
D
Brass
N
K
S
T
U
L
B
G
P
Brass
Stainless steel
Latch sleeve + earthing crown
Material
chrome
brass/bronze
brass/bronze
nickel
brass/bronze
black chrome 3) brass/bronze
Stainless steel
–
Surf. treatment
nickel 2)
nickel
nickel
nickel 2)
brass/bronze
nickel 2)
stainless steel
–
stainless steel
Aluminium alloy
anodized
brass/bronze
nickel 2)
PEEK (natural)
–
brass/bronze
nickel
–
brass/bronze
POM (black)
H
–
PSU
–
PPS/brass
–/nickel
PPSU
R
–
brass/bronze
brass/bronze
brass/bronze
–
l
nickel
l
brass
l
–
l
2)
brass
nickel
2)
brass
stainless steel
2)
brass
l
nickel
nickel
nickel
l
nickel
brass
brass
2)
nickel
nickel
nickel
nickel
nickel
brass
nickel
brass
2)
Note
Surf. treatment
brass
2)
Remarks
Material
brass
2)
–
Stainless steel
Other metallic components
l
1)
nickel
Only for FFP, ERN and PCP (S series)
brass
nickel
Only for FFL (S series)
brass
nickel
Only for EPL and EXP (S series)
nickel
Note: detailed characteristics of these materials and treatments are presented on page 182.
1) see «variant» for the colour.
2) in the E series, the latch sleeve is chrome-plated.
3) surface not conductive use socket with earthing tag (ERN model) to carry shield.
Only for FFP, ERN and PCP (S series)
Only for FFL (S series)
1)
1)
l
l
l
l
l
l
l First choice alternative
l Special order alternative
Insulators (S and E series)
Ref.
L
Y
T
T
V
N
Material
Contact type
Remarks
PEEK
Solder or print
PTFE
Solder
only for unipole types
PI
Solder
only for multipole types of the S or E series
PEEK
FEP
PA6.6
Crimp
Solder
Solder
l
l
l
only for multipole types of the S or E series
l
material for 5S/5E and 6S/6E series multipole inserts
l
Note: detailed characteristics of these materials are presented on page 187.
l First choice alternative
Note
l
l Special order alternative
Contacts (S and E series)
Soldering characteristics
– no need to order specific tools, a simple soldering iron
is sufficient
– ideal for very small and fragile conductors
– contacts with solder cups to allow the solder to flow
Note: see page 188 for more information.
112
Crimping characteristics
–
–
–
–
practical, quick contact fixing outside the insulator
possible use at high temperature
need to order specific tools
no risk of heating the insulator during the conductorcontact fixing
– high tensile strength
– totally lead-free solution
www.lemo.com
Contacts reference for plugs, free or fixed sockets
Reference
Contact type
Male Female
Solder
øA
(mm)
0.5
0.7
0.9
øA
1.3
1.6
øC
øA
A
øC
L
2.0
3.0
4.0
5.0
6.0
8.0
Crimp
fig. 1
øA
øC
øA
øC
fig. 2
øA
øC
øC
øA
Print
Contact
øC
Form
(mm) per fig.
0.45
–
0.80
–
0.60
1.00
1.40
1.80
2.70
3.70
5.20
5.20
7.00
12.0
11.50
0.7
0.45
0.7
–
–
Solid
AWG Section
max.
max.
(mm2)
28
24
22
0.34
®
Conductor
Stranded
AWG
Section (mm2)
Fr 1)
(N) Notes
min.
max.
min.
max.
–
26
–
0.14
–
–
28
–
18
–
1.00
–
202)
14
1.50
–
16
–
10
4.00
–
–
12
–
–
–
–
10
6.00
–
10
–
–
–
–
–
8
–
–
–
–
–
–
–
–
–
–
–
–
–
8
4
0
0.80
1
0.9
1.10
1
0.9
0.45
2
–
–
32
28
2
–
–
24
20
–
–
–
0.34
–
1.00
0.09
–
0.50
16
–
222)
20
–
–
0.09
0.25
®
0.50
1.50
4.00
10.00
–
–
21.00
26
222)
0.140
–
24
20
0.250
–
–
10.00
–
–
6.00
–
–
–
50.00
l
–
–
–
0.34
22
0.50
30
l
C
M
B
P
C
M
B
P
G
U
C
M
B
P
G
U
C
M
B
P
C
M
B
P
D
N
L dimensions and C are detailed in the section on PCB drilling pattern.
See page 167.
l
V
V
L dimensions and C are detailed in the section on PCB drilling pattern.
See page 168.
l
0.9
1.3
1.3
1.3
1.6
1.6
2.0
2.0
0.80
1.40
1.10
0.80
1.90
1.40
2.40
1.90
2
–
–
2
–
–
1
2
–
–
–
–
–
32
26
20
26
28
l
18
0.500
1.00
40
l
40
l
l
40
18
0.340
1.00
50
l
65
l
–
16
122)
18
0.50
30
0.34
–
–
0.250
0.09
0.140
1
–
0.035
222)
18
2
l
30
–
22
l
0.34
–
–
22
0.140
1
–
0.09
222)
142)
2
0.035
14
1.000
1.500
1.500
1.50
2.50
1.50
50
65
l
l
l
L
øC
øA
øA
øC
L
Print (elbow)
L
øA
øC
Note:
1)
2)
contact retention force in the insulator (according to IEC 60512-8 test 15 a).
for a given AWG, the diameter of some stranded conductor designs is larger than the solder cup diameter.
Make sure that the maximum conductor diameter is smaller than ø C.
l First choice alternative
www.lemo.com
l Special order alternative
113
®
®
Contacts reference for coupler and plug with socket
A
L
M
Contact type
Male - Female
Female - Male
Female - Female
Remarks
contact configuration is explained below
contact configuration is explained below
contact configuration is explained below
Contacts reference for fixed and free couplers RMA, RAD and SWH
L
A
A
Unipole
1
Multipole
(odd)
3
1
4
6
Multipole
(even)
2
1
3
A
2
5
Reference for plug
A
M
Female - Male
Reference for plug
Unipole
Reference for plug
L
Reference for plug
Male - Female
Reference for plug
A
L
A
L
A
2
Female - Female
Unipole
2
Multipole
(odd)
1
3
6
4
Multipole
(even)
1
3
3
2
2
1
3
6
4
5
A1)
A
Reference for plug
Ref.
5
A
2
1
A1)
3
2
3
1
4
6
A1)
5
Use of plugs for mating with RAD, RMA and SWH couplers
Unipole type:
Reference M for coupling two identical plugs fitted with male contact (contact reference A).
Reference L for coupling a plug fitted with male contacts (contact reference A) at the flange end for RAD and SWH and
an inverted plug fitted with female contacts (contact reference L) at the other end.
Reference A for the inverted version of code L.
Multipole type:
Reference L
for coupling a standard plug (contact reference A) at the flange end for RAD and SWH and an inverted plug
(contact reference as indicated in the above table) at the other end.
Reference M for coupling two standard plugs (contact type A).
Only available for RAD and RMA models.
Note: 1) this connector combination does not allow for contact numbering. One of the plugs has to be cable mounted in a way to ensure correct
signal continuity.
114
www.lemo.com
®
®
Collets (S and E series)
C, K and L type collets for S series
L type
(non EMC)
Reference
00
0S
1S
Type
Code
C
17
C
22
C
27
C
31
K
37
K
42
L
27
L
31
C
22
C
32
C
37
C
44
K
52
K
57
K
62
L
22
L
32
L
37
L
44
L
48
C
22
C
32
C
42
C
52
C
57
C
62
K
72
K
82
K
87
øA
øB
øA
K type
oversize
cable collet
øA
øB
C type
Collet ø
øA
1.7
2.2
2.7
ø B
1.5
–
–
3.1
2.7
4.2
3.7
3.7
2.7
3.1
–
–
–
Cable ø
max.
1.7
3.7
4.4
2.6
3.0
3.7
–
3.7
3.7
5.7
5.2
2.2
–
5.2
6.2
3.2
3.7
4.4
4.8
–
5.2
–
–
–
–
5.2
5.7
6.2
2.2
7.2
–
6.2
8.2
8.7
5.2
6.7
6.7
52
L
62
L
66
C
27
C
32
C
42
> 3.2
C
52
C
62
> 4.2
C
72
C
82
C
87
K
97
K
11
L
32
L
42
L
52
L
62
L
72
L
82
L
87
> 3.7
2.2
2.6
1.3
> 5.7
> 3.2
2)
4.4
1.4
> 2.2
5.2
> 4.2
6.2
7.2
8.2
8.7
3)
2)
3.2
5.7
2)
1.3
3.5
4.8
2)
> 5.2
4.3
3.7
1S
> 3.2
> 2.2
4.2
5.2
L
3.2
–
5.7
42
> 3.7
4.2
–
L
> 2.2
4.4
2.2
5.2
32
> 2.2
–
–
L
3.2
2.2
3.2
22
> 2.7
2.2
4.4
L
1.3
3.1
–
–
Code
> 1.7
2.7
Reference
Type
2.2
2.2
3.2
min.
Notes
> 3.2
2)
1) 2)
1) 2)
2S
Collet ø
Cable ø
øA
ø B
max.
min.
3.2
–
3.2
> 2.2
2.2
4.2
5.2
6.2
–
–
–
–
2.2
4.2
5.2
1.2
> 3.2
> 4.2
6.2
> 5.2
2.7
1.3
6.6
–
6.5
3.2
–
3.2
> 2.5
5.2
> 4.2
2.7
4.2
5.2
6.2
–
–
–
–
7.2
6.7
8.7
6.7
8.2
9.7
10.5
3.2
4.2
5.2
6.2
7.2
8.2
8.7
6.7
9.0
4.2
6.2
7.2
8.2
8.7
9.7
5.9
> 5.2
–
–
7.2
8.2
8.7
1) 2)
> 8.7
6.2
–
2)
> 8.2
> 3.2
–
2)
> 7.2
4.2
5.2
2)
> 6.2
–
–
2)
> 5.2
10.5
3.2
2)
> 3.2
9.0
–
Notes
> 9.5
2.5
2)
> 4.2
2)
> 6.2
> 7.2
> 8.2
2)
2)
2)
2)
1) 2)
> 5.2
> 5.7
> 6.2
> 7.2
> 8.2
Note: All dimensions are in millimetres.
1) these collets cannot be used for connectors models with nut for fitting a bend relief. 2) these collets cannot be used for elbow connectors. 3) the inner
diameter of the smallest bend relief available is 2.5 mm.
www.lemo.com
115
®
®
C, K and L type collets for S series
L type
(non EMC)
Reference
3S
4S
Type
Code
C
42
C
57
C
72
C
87
C
97
C
11
K
12
K
13
L
42
L
57
L
72
L
87
L
97
L
11
C
52
C
62
C
72
C
82
C
92
C
10
C
11
øA
øB
øA
K type
oversize
cable collet
øA
øB
C type
Collet ø
øA
4.2
5.7
7.2
8.7
9.7
10.5
ø B
7.7
7.7
7.7
8.7
9.0
Cable ø
max.
4.2
5.7
7.2
8.7
9.7
min.
2.6
4.3
5.8
13.2
12.2
13.0
12.1
5.7
–
5.7
> 4.2
8.7
> 7.2
4.2
7.2
8.7
9.7
–
–
–
–
12.0
4.2
7.2
9.7
10.7
–
10.7
6.2
–
6.0
5.2
7.2
8.2
9.2
10.2
11.2
–
–
–
–
–
–
5.0
7.0
8.0
9.0
10.0
11.0
4S
8.8
10.5
–
Reference
7.3
9.0
12.2
Notes
9.8
11.1
2.6
2)
> 5.7
2)
> 8.7
> 9.7
4.1
2)
2)
2)
1) 2)
5.1
6.1
7.1
8.1
9.1
10.1
Type
Code
C
12
C
13
K
14
K
15
K
16
K
17
K
18
K
19
K
20
K
21
K
22
L
52
L
62
L
72
L
82
L
92
L
10
L
11
L
12
L
13
Collet ø
Cable ø
øA
ø B
max.
min.
13.2
12.2
13.0
12.6
15.2
–
12.2
14.2
16.2
17.2
18.2
19.2
–
–
–
–
–
–
20.2
19.7
22.2
19.7
21.2
5.2
6.2
7.2
8.2
9.2
19.7
–
–
–
–
–
12.0
14.0
15.0
16.0
17.0
18.0
19.0
20.0
21.0
22.0
5.0
6.0
7.0
8.0
9.0
10.2
–
10.0
12.2
–
12.0
11.2
13.2
–
–
11.1
Notes
13.1
1)
15.1
1)
14.1
16.1
17.1
18.1
19.1
20.1
21.1
4.1
5.1
6.1
7.1
8.1
9.1
11.0
10.1
13.0
12.6
11.1
1)
1)
1)
1)
1)
1)
1)
2)
2)
2)
2)
2)
2)
2)
2)
2)
Note: All dimensions are in millimetres.
1) these collets cannot be used for connectors models with nut for fitting a bend relief.
2) these collets cannot be used for elbow connectors.
116
www.lemo.com
®
®
C, K and L type collets for S series
L type
(non EMC)
Reference
5S
Type
Code
C
72
C
82
C
92
C
10
C
11
C
12
C
13
C
14
C
15
C
16
C
17
C
18
C
19
C
20
C
21
C
22
K
23
K
24
K
25
øA
øB
øA
K type
oversize
cable collet
øA
øB
C type
Collet ø
øA
7.2
8.2
9.2
ø B
–
–
–
Cable ø
max.
7.0
8.0
9.0
10.2
–
10.0
12.2
–
12.0
11.2
13.2
14.2
15.2
16.2
17.2
18.2
19.2
–
–
–
–
–
–
–
–
20.2
19.7
22.2
19.7
21.2
23.2
24.2
25.2
19.7
–
–
–
min.
6.1
7.1
8.1
9.1
11.0
10.1
13.0
12.1
14.0
15.0
16.0
17.0
18.0
19.0
20.0
21.0
22.0
23.0
24.0
25.0
11.1
13.1
14.1
15.1
16.1
17.1
18.1
19.1
20.1
21.1
22.1
23.1
24.1
Notes
1)
1)
1)
Reference
5S
1)
1)
1)
1)
1)
1)
1)
1)
1)
1)
1)
1)
1)
1)
1)
1)
Type
Code
K
26
K
27
K
28
K
29
K
30
L
92
L
10
L
11
L
12
L
13
L
14
L
15
L
16
L
17
L
18
L
19
L
20
L
21
Collet ø
Cable ø
øA
ø B
max.
min.
27.2
–
27.0
26.1
26.2
–
28.2
27.2
30.2
27.2
29.2
9.2
27.2
–
26.0
28.0
29.0
30.0
9.0
13.0
12.1
12.0
15.2
16.2
17.2
18.2
19.2
20.2
21.2
–
–
–
–
–
–
–
–
1)
1) 2)
–
14.2
1)
10.1
12.2
–
29.1
1)
11.0
10.0
13.2
28.1
1)
1) 2)
–
–
27.1
1)
8.1
10.2
11.2
25.1
Notes
14.0
15.0
16.0
17.0
18.0
19.0
20.0
21.0
9.1
11.1
13.1
14.1
15.1
16.1
17.1
18.1
19.1
20.1
1) 2)
1) 2)
1) 2)
1) 2)
1) 2)
1) 2)
1) 2)
1) 2)
1) 2)
1) 2)
1) 2)
Note: All dimensions are in millimetres.
The 5S.112 is only available with L type of collet.
1) these collets cannot be used for connectors models with nut for fitting a bend relief.
2) these collets cannot be used for elbow connectors.
www.lemo.com
117
®
®
C, K and L type collets for S series
L type
(non EMC)
Reference
6S
Type
Code
C
12
C
13
C
14
C
15
C
16
C
17
C
18
C
19
C
20
C
21
C
22
C
23
C
24
C
25
C
26
C
27
C
28
C
29
C
30
øA
øB
øA
K type
oversize
cable collet
øA
øB
C type
Collet ø
øA
12.2
13.2
14.2
15.2
16.2
17.2
18.2
19.2
20.2
21.2
22.2
ø B
–
–
–
–
–
–
–
–
–
–
–
23.2
–
25.2
–
24.2
26.2
27.2
–
–
–
28.2
27.2
30.2
27.2
29.2
27.2
Cable ø
max.
12.0
13.0
14.0
15.0
16.0
17.0
18.0
19.0
20.0
21.0
22.0
23.0
24.0
25.0
26.0
27.0
28.0
29.0
30.0
min.
11.1
12.1
13.1
14.1
15.1
16.1
17.1
18.1
19.1
20.1
21.1
22.1
23.1
24.1
25.1
26.1
27.1
28.1
29.1
Notes
1)
1)
1)
Reference
6S
1)
1)
1)
1)
1)
1)
1)
1)
1)
1)
1)
1)
1)
1)
1)
1)
Note: All dimensions are in millimetres.
1) these collets cannot be used for connectors models with nut for fitting a bend relief.
2) these collets cannot be used for elbow connectors..
118
Type
Code
L
12
L
13
L
14
L
15
L
16
L
17
L
18
L
19
L
20
L
21
L
22
L
23
L
24
L
25
L
26
L
27
L
28
L
29
L
30
Collet ø
Cable ø
øA
ø B
max.
min.
13.2
–
13.0
12.1
12.2
14.2
15.2
16.2
17.2
18.2
19.2
20.2
21.2
22.2
23.2
24.2
25.2
26.2
27.2
28.2
29.2
30.2
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
12.0
14.0
15.0
16.0
17.0
18.0
19.0
20.0
21.0
22.0
23.0
24.0
25.0
26.0
27.0
28.0
29.0
30.0
11.1
13.1
14.1
15.1
16.1
17.1
18.1
19.1
20.1
21.1
22.1
23.1
24.1
25.1
26.1
27.1
28.1
29.1
Notes
1) 2)
1) 2)
1) 2)
1) 2)
1) 2)
1) 2)
1) 2)
1) 2)
1) 2)
1) 2)
1) 2)
1) 2)
1) 2)
1) 2)
1) 2)
1) 2)
1) 2)
1) 2)
1) 2)
www.lemo.com
®
®
C and K type collets for E series
Reference
øB
K type
oversize
cable collet
øA
øA
øB
C type
Collet ø
Cable ø
Reference
Collet ø
Cable ø
Type Code
C
70
7.2
–
7.0
6.6
C
75
8.2
8.2
7.5
7.1
Notes
0E
1E
2E
C
10
1.6
–
1.2
1.0
1)
C
15
1.6
–
1.5
1.3
1)
C
20
2.1
–
2.0
1.6
1)
C
80
8.2
8.2
8.0
7.6
C
25
3.1
–
2.5
2.1
C
85
9.2
8.6
8.5
8.1
C
30
3.1
–
3.0
2.6
K
90
9.2
–
9.0
8.6
4)
C
35
4.2
4.2
3.5
3.1
K
95
10.2 10.2
9.5
9.1
4)
C
40
4.2
4.2
4.0
3.6
K
10
10.2 10.2 10.0
9.6
4)
C
45
5.2
5.2
4.5
4.1
K
11
11.2 10.6 10.5 10.1
C
50
5.2
5.2
5.0
4.6
C
30
3.2
–
3.0
2.6
C
15
1.6
–
1.5
1.3
C
35
4.2
–
3.5
3.1
C
20
2.2
–
2.0
1.6
C
40
4.2
–
4.0
3.6
C
25
3.2
–
2.5
2.1
C
45
5.2
–
4.5
4.1
C
30
3.2
–
3.0
2.6
C
50
5.2
–
5.0
4.6
C
35
4.2
–
3.5
3.1
C
55
6.2
–
5.5
5.1
C
40
4.2
–
4.0
3.6
C
60
6.2
–
6.0
5.6
C
45
5.2
–
4.5
4.1
C
65
7.2
–
6.5
6.1
C
50
5.2
–
5.0
4.6
C
70
7.2
–
7.0
6.6
C
55
6.2
6.2
5.5
5.1
C
75
8.2
–
7.5
7.1
C
60
6.2
6.2
6.0
5.6
C
80
8.2
–
8.0
7.6
C
65
7.2
6.7
6.5
6.1
C
85
9.2
–
8.5
8.1
K
70
7.2
–
7.0
6.6
3)
C
90
9.2
–
9.0
8.6
K
75
8.2
8.2
7.5
7.1
3)
C
95
10.2 10.2
9.5
9.1
K
80
8.2
8.2
8.0
7.6
3)
C
10
10.2 10.2 10.0
9.6
K
85
9.2
8.6
8.5
8.1
3)
C
11
11.2 10.6 10.5 10.1
C
15
2.2
–
1.5
1.3
K
11
12.3
12.0 10.6
5)
C
20
2.2
–
2.0
1.6
K
12
13.8 13.8 12.8 12.1
5)
C
25
3.2
–
2.5
2.1
K
13
13.8 13.8 13.5 12.9
5)
C
30
3.2
–
3.0
2.6
K
14
15.3 15.3 14.0 13.6
5)
C
35
4.2
–
3.5
3.1
K
15
15.3 15.3 15.0 14.1
2)
C
40
4.2
–
4.0
3.6
C
45
5.2
–
4.5
4.1
C
50
5.2
–
5.0
4.6
C
55
6.2
–
5.5
5.1
C
60
6.2
–
6.0
5.6
C
65
7.2
–
6.5
6.1
www.lemo.com
ø A
ø B
max.
Notes
Type Code
min.
2E
3E
ø A
ø B
–
max.
min.
4)
Note: all dimensions are in millimetres.
1) the inner diameter of the smallest bend relief available is 2.5 mm.
2) the inner diameter of the largest bend relief available is 14.5 mm.
3) for 2B bend relief.
4) for 3B bend relief.
5) for 4B bend relief.
119
®
®
C and K type collets for E series
øA
øB
C type
Reference
4E
Collet ø
ø B
Cable ø
Type Code
ø A
max.
min.
C
50
6.3
–
5.0
4.8
C
55
6.3
–
5.5
5.1
C
60
6.3
–
6.0
C
65
7.3
–
6.5
C
70
7.3
–
C
75
8.3
C
80
C
Reference
Notes
øA
øB
øB
øA
C type
K type
oversize
cable collet
Collet ø
Type Code
ø A
C
10
11.8
C
11
5.6
C
6.1
C
7.0
6.6
–
7.5
8.3
–
85
9.3
C
90
C
Notes
max.
min.
–
10.5
9.6
11.8
–
11.5 10.6
12
13.8
–
12.5 11.6
13
13.8
–
13.5 12.6
C
14
15.8
–
14.5 13.6
7.1
C
15
15.8
–
15.5 14.6
1)
8.0
7.6
C
16
17.8
–
16.5 15.6
1)
–
8.5
8.1
C
17
17.8
–
17.5 16.6
1)
9.3
–
9.0
8.6
C
18
19.8
–
18.5 17.6
1)
95
10.8
–
9.5
9.1
C
19
19.8
–
19.5 18.6
1)
C
10
10.8
–
10.5
9.6
C
20
21.8
–
20.5 19.6
1)
C
11
12.3
–
12.0 10.6
C
21
21.8
–
21.5 20.6
1)
C
12
13.8 13.8 12.8 12.1
C
22
23.8 23.8 22.5 21.6
1)
C
13
13.8 13.8 13.5 12.9
C
23
23.8 23.8 23.5 22.6
1)
C
14
15.3 15.3 14.0 13.6
C
14
14.2
–
14.0 13.0
1)
C
15
15.3 15.3 15.0 14.1
2)
C
15
15.2
–
15.0 14.1
1)
K
16
17.8
–
16.5 15.6
1)
C
16
15.7
–
15.5 14.6
1)
K
17
17.8
–
17.5 16.6
1)
C
17
16.7
–
16.5 15.6
1)
K
18
19.8
–
18.5 17.6
1)
C
18
18.2
–
18.0 17.1
1)
K
19
19.8
–
19.5 18.6
1)
C
21
23.2
–
21.5 20.6
1)
K
20
21.8
–
20.5 19.6
1)
C
22
23.2
–
22.0 21.1
1)
K
21
21.8
–
21.5 20.6
1)
C
23
23.2
–
23.0 22.1
1)
K
22
23.8 23.8 22.5 21.6
1)
C
27
27.2
–
27.0 26.1
1)
K
23
23.8 23.8 23.5 22.6
1)
L
30
30.2
–
30.0 29.5
1)
5E
6E
ø B
Cable ø
Note: all dimensions are in millimetres.
1) these collets cannot be used for connector models with nut for fitting a bend relief. No bend relief available for this cable size.
2) the inner diameter of the largest bend relief available is 14.5 mm.
120
www.lemo.com
®
®
Variant (S and E series)
Bend relief for S series models with collet
Need to be ordered
00
0S
1S
2S
3S
4S
Ref.
Z
Z
Z
Z
Z
Z
www.lemo.com
Collet
Code
Need to be ordered
separately
(see pages 145 and 146)
K
37 to 42
GMA.0B.0ll.Dl
C
32 to 44
GMA.0B.0ll.Dl
32 to 48
GMA.0B.0ll.Dl
Type
C
L
17 to 31
27 to 31
K
52 to 62
C
32 to 62
L
K
72 to 87
C
42 to 87
L
32 to 66
K
97 to 11
C
57 to 97
L
42 to 87
K
12 to 13
C
82 to 13
L
L
57 to 97
82 to 13
GMA.00.0ll.Dl
GMA.00.0ll.Dl
GMA.1B.0ll.Dl
GMA.1B.0ll.Dl
GMA.2B.0ll.Dl
GMA.1B.0ll.Dl
GMA.2B.0ll.Dl
GMA.3B.0ll.Dl
GMA.2B.0ll.Dl
GMA.3B.0ll.Dl
GMA.4B.0ll.Dl
GMA.3B.0ll.Dl
Bend relief for E series models with collet
Need to be ordered
0E
1E
2E
3E
4E
5E
Ref.
Z
Type
Collet
Code
Need to be ordered
separately
(see pages 145 and 146)
15 to 65
GMA.1B.lll.ll
C
10 to 50
GMA.0B.lll.ll
K
70 to 85
GMA.2B.lll.ll
Z
C
Z
C
15 to 85
Z
C
30 to 10
K
K
90 to 10
11 to
15 1)
Z
C
50 to 15 2)
Z
C
10 to 14
Note: all dimensions are in millimetres.
1) for K15 see page 119.
2) for C15 see page 120.
GMA.2B.lll.ll
GMA.3B.lll.ll
GMA.3B.lll.ll
GMA.4B.lll.ll
GMA.4B.lll.ll
GMA.4B.lll.ll
GMA.4B.0ll.Dl
GMA.4B.0ll.Dl
121
®
®
Colour of connectors shell made of plastic material and aluminium alloys
Ref.
Colour
A
blue
B
Plastic shell
PSU
PPSU
Aluminium alloys
PA.6
Anodized colour
l
l
white
l
l
G
grey
l
l
J
yellow
l
M
brown
l
N
black
l
l
R
red
l
l
S
orange
l
Anodized colour
for bend relief collet nut
l
T
natural
l
V
green
l
l
L
black
l
X
natural
l
F
cream
l
Note: other anodizing colours are available for
connectors with collet nut for bend relief. Please
consult us.
Watertight and vacumtight socket and coupler models (S and E series) (not connected)
Reference
Model
Watertight Vacuumtight
S
P
PV
EWB, HCP, HGP,
HGW, SWH
E
P
PV
EBR, HGP, SWH
O-ring and gasket material (E series)
Standard connectors are delivered with silicone o-ring and gaskets. The vacuumtight models, identified with the letter «PV»,
are delivered with Viton® gaskets. Other gaskets material can be delivered upon special request.
O-ring material
Ref.
H
FPM (Viton®)
E
EPDM
D
FPM (Viton®) and collet nut for bend relief
122
www.lemo.com
®
®
M Series
The M Series connector offers a new innovative design for avionics, aerospace, military, security, motorsport and heavy
duty applications.
Made of high-strength aluminium, this connector is one of the lightest and most compact of the LEMO product line.
A one-grip ratchet screw system enables quick and secure coupling of the connectors. The arctic grip makes it easy to
manipulate the connector while wearing gloves or when the connector is located in a difficult to access area.
Features
– Ratchet-coupling mechanism
– Compact design for space savings
– Oil and fuel resistant
– 360° screening for full EMC shielding
– Colour coding / keying
– Scoop proof
– Threaded for MIL-DTL-38999L backshell
Metal housing models
– Quick mating: less than 3/4 turn to seat
– Lightweight
– High vibration and shock resistance
– Sealed to IP68 when mated
– Reverse gender configuration
– Pin configuration from 2 to 114 contacts
Straight plugs
Free sockets
Fixed sockets
FA•
FG•
FM•
EG•
FA•
FG•
FM•
EG•
PM•
PV•
PB•
FA•
FG•
FM•
EC•
FW•
FX•
EC•
FW•
FX•
ED•
PE•
PF•
PH•
FW•
FX•
ED•
PE•
PF•
PH•
Straight plugs
USB models
FG•
Fibre optic models
www.lemo.com
PM•
PV•
PB•
FM•
Straight plugs
PM•
Fixed sockets
EG•
PV•
PB•
Watertight
model
(unmated)
EG•
Fixed sockets
Free sockets
FM•
EG•
PM•
FG•
ED•
PH•
PH•
Fixed socket
HE•
123
®
®
Part Numbering System
Plug
F M N . 1 M. 3 0 5 . X L C
F G N . 1 M. 3 0 5 . X L C M
Free socket
Fixed socket
Model
P M N . 1 M. 3 0 5 . X L M T
H E N . 1 M. 3 0 5 . X L N P
Variant:
T = Mold stop
P = Potted
M = MIL-DTL-38999L shell thread
Alignment key
Series
Contact
Insert configuration
Insulator:
L = PEEK (multipole)
R = PEEK (mixed multipole)
Housing:
C = Chrome-plated brass
X = Nickel-plated aluminium alloy 1)
I = NiCorAlTM Nickel
fluorocarbon polymer
aluminium alloy 2)
FMN.1M.305.XLC = straight plug with key (N), 1M series, multipole type with 5 contacts, outer shell in anthracite nickel-plated aluminium
alloy, PEEK insulator, male crimp contacts
FGN.1M.305.XLCM = straight plug with key (N), arctic grip, 1M series, multipole type with 5 contacts, outer shell in anthracite nickelplated aluminium alloy, PEEK insulator, male crimp contacts and with MIL-DTL-38999L thread for additional backshell (not supplied).
PMN.1M.305.XLMT = free socket with key (N), 1M series, multipole type with 5 contacts, outer shell in anthracite nickel-plated aluminium
alloy, PEEK insulator, female crimp contacts and mold stop.
HEN.1M.305.XLNP = fixed socket, nut fixing, with key (N), 1M series, multipole type with 5 contacts, outer shell in anthracite nickelplated aluminium alloy, PEEK insulator, female print contacts, watertight.
Note: 1) anthracite colour / 48 hours salt fog resistance. 2) anthracite colour / 500 hours salt fog resistance RoHS 2/REACH.
Part Section Showing Internal Components
Fixed socket
1
2
3
4
5
6
5
4
6
3
2
1
1
3
2
7
5
6
outer shell
o-ring
hexagonal nut
insulator
female contact
earthing crown
Straight plug
4
1
2
3
4
5
6
7
outer shell
insulator
male contact
rear seal
tightening screw
ratchet mechanism
spring
More informations on: https://www.lemo.com/catalog/ROW/UK_English/M_series.pdf
124
www.lemo.com
F Series
®
®
The F series connectors have been specially developed to meet the most demanding requirements in terms of dimensions, weight and watertightness. Our manufacturing programme includes now 8 series. This series provides customers
with many features and benefits including:
– push-pull self-latching system for safe connection
– sealed to IP67 for environmental protection when mated according to IEC 60529
– compact scoop-proof design and use of aluminium alloy
– high shock and vibration resistance
– multipole types with 2 to 68 contacts or multifibre optic or mixed FO + LV in 2F series
– crimp or print contacts (straight or elbow)
– keys ensuring ease of blind mating
– colour coded key options for system security.
The F series connectors are available in 3 different materials:
– for high shock and vibration resistance, LEMO recommends using Y code material (with beryllium copper latch sleeve).
– for environmental resistance and latching cycle endurance, LEMO recommends using the C code material
(brass outershell).
– for lightweight and latching cycle endurance, LEMO recommends using X code material (aluminium shell).
– for lightweight and salt spray corrosion resistance, LEMO recommends using I code material (aluminium shell).
Each series includes several models of plugs and sockets available in contact configurations adapted to all round cables,
including up to 68 conductors, and a maximum diameter of 34 mm. Since LEMO connectors are perfectly screened and
designed to guarantee very low resistance to shell electrical continuity, they are particularly adapted to applications
where electromagnetic compatibility (EMC) is important. A large number of accessories as well as tooling for cable
assembly are available.
Metal housing models
Straight plugs
FGl
Fixed sockets
Fixed sockets
ECl
EGl
EDl
Free socket
PEl
PHl
FNl
ECl
EEl
PBl
EHl
EFl
Models for fibre optic
Straight plug
FGl
www.lemo.com
Watertight models
Fixed socket
Fixed sockets
EHl
HEl
HEl
125
®
®
Part Numbering System
T 66 Z
F G N . 0 F . 3 0 5 . Y L C or
Plug
P H N . 0 F . 3 0 5 . X L M
Free socket
Fixed socket
Model
H E N . 0 F . 3 0 5 . X L N P
T = f.o. cable adapter and ø 5)
Z = collet nut for bend relief
Variant:
F = reduced unlatching force 1)
S = o-ring & gasket in silicone 2)
Variant 3)
Contact 4)
Alignment key
Insulator: L = PEEK
Series
Housing
Insert configuration
FGN.0F.305.YLC = straight plug with key (N), 0F series, multipole type with 5 contacts, outer shell in anthracite nickel-plated aluminium
alloy, beryllium copper latch sleeve, PEEK insulator, male crimp contacts.
PHN.0F.305.XLM = free socket with key (N), 0F series, multipole type with 5 contacts, outer shell in anthracite nickel-plated aluminium
alloy, PEEK insulator, female crimp contacts.
HEN.0F.305.XLNP = fixed socket, nut fixing, with key (N), 0F series, multipole type with 5 contacts, outer shell in anthracite nickel-plated
aluminium alloy, PEEK insulator, female print contacts, watertight.
Note:
1)
5)
for straight plug only. 2) with shell material code X or Y. 3) potting for HEl only. 4) HEl available only with print contacts (straight or elbow).
connectors for fibre-optic are delivered without the fibre optic contacts, they must be ordered separately.
Part Section Showing Internal Components
Straight socket
Straight plug
5
1
2
3
4
5
6
3
2
4
1
6
1
4
5
3
5
outer shell
earthing crown
insulator
female contact
rear seal
front nut
2
6
1
2
3
4
5
6
outer shell
latch sleeve
insulator
male contact
gasket
rear seal
More informations on: https://www.lemo.com/catalog/ROW/UK_English/f_series.pdf
126
www.lemo.com
SPARE PARTS
®
®
Spare parts for crimp contacts
Insulator part number
Male contact
ø (mm)
Female contact
A
C
Cond. AWG
Fig.
Types
min. max.
00
TT
302 / 303 / 304
FGG.00.30l.YL EGG.00.40l.YL
0B
0K
0T
302 / 303
FGG.0B.30l.YL EGG.0B.40l.YL
304 / 305
FGG.0B.30l.YL EGG.0B.40l.YL
0.80 1 26 22
0.7
0.45 2 32 28
306 / 307 / 309
FGG.0B.30l.YL
0.5 0.45 1
0S
1B
1K
1T
1S
2B
2K
2T
302
–
–
–
303 / 304
302 / 303
FGG.1B.30l.YL EGG.1B.40l.YL
304 / 305
–
–
FGG.1B.30l.YL EGG.1B.40l.YL
0.5 0.45 1
FGG.0B.560.ZZC EGG.0B.660.ZZM
0.45 2 32 28
FGG.0B.562.ZZC EGG.0B.662.ZZM
0.9 0.80 2
26 22
32 28
0.80 1 26 22
0.7
0.45 2 32 28
1.40 1 20 18
1.3
1.10 2 24 20
1.10 1 24 20
0.9
0.80 2 26 22
302
–
1.40 1 20 18
1.3
1.10 2 24 20
FGG.2B.302.YL EGG.2B.402.YL
303
FGG.2B.303.YL EGG.2B.403.YL
304 / 305
306 / 307
FGG.2B.30l.YL EGG.2B.40l.YL
312 / 314 / 316
318 / 319
FGG.2B.3ll.YL EGG.2B.4ll.YL
FGG.2B.3ll.YL EGG.2B.4ll.YL
FGG.0B.554.ZZC
–
FGG.0B.562.ZZC EGG.0B.662.ZZM
26 22
0.5 0.45 1
302
FGG.0B.556.ZZC EGG.0B.656.ZZM
0.45 2 32 28
0.9 0.80 2
–
–
FGG.0B.555.ZZC EGG.0B.655.ZZM
FGG.0B.560.ZZC EGG.0B.660.ZZM
FGG.1B.3ll.YL
–
FGG.0B.561.ZZC EGG.0B.661.ZZM
1.10 1 24 20
310 / 314 / 316
Female
1.10 1 24 20
FGG.1B.30l.YL EGG.1B.40l.YL
304
Male
FGG.00.554.ZZC EGG.00.654.ZZM
306 / 307 / 308
–
32 28
0.80 1 26 22
0.7
0.45 2 32 28
308 / 310
128
Contact part number
32 28
1.10 1 24 20
0.9
0.80 2 26 22
2.40 1 16 12
2.0
1.90 2 18 14
1.90 1 18 14
1.6
1.40 2 22 18
FGG.0B.561.ZZC EGG.0B.661.ZZM
FGG.0B.555.ZZC EGG.0B.655.ZZM
FGG.0B.556.ZZC EGG.0B.656.ZZM
FGG.1B.565.ZZC EGG.1B.665.ZZM
FGG.1B.566.ZZC EGG.1B.666.ZZM
FGG.1B.560.ZZC EGG.1B.660.ZZM
FGG.1B.561.ZZC EGG.1B.661.ZZM
FGG.1B.555.ZZC EGG.1B.655.ZZM
FGG.1B.554.ZZC
FGG.1B.556.ZZC EGG.1B.656.ZZM
–
FGG.1B.565.ZZC EGG.1B.665.ZZM
FGG.1B.566.ZZC EGG.1B.666.ZZM
FGG.1B.560.ZZC EGG.1B.660.ZZM
FGG.1B.561.ZZC EGG.1B.661.ZZM
FGG.2B.575.ZZC EGG.2B.675.ZZM
FGG.2B.576.ZZC EGG.2B.676.ZZM
FGG.2B.570.ZZC EGG.2B.670.ZZM
FGG.2B.571.ZZC EGG.2B.671.ZZM
1.40 1 20 18
FGG.2B.565.ZZC EGG.2B.665.ZZM
0.80 2 26 22
FGG.2B.567.ZZC EGG.2B.667.ZZM
0.9 0.80 2
26 22
FGG.2B.561.ZZC EGG.2B.661.ZZM
0.80 1 26 22
0.7
0.45 2 32 28
FGG.2B.555.ZZC EGG.2B.655.ZZM
24 20
FGG.2B.566.ZZC EGG.2B.666.ZZM
1.10 1 24 20
FGG.2B.560.ZZC EGG.2B.660.ZZM
0.45 2 32 28
FGG.2B.562.ZZC EGG.2B.662.ZZM
1.3 1.10 2
FGG.2B.556.ZZC EGG.2B.656.ZZM
www.lemo.com
®
®
Tools for crimp contacts
Positioners part number 1)
Types
00
TT
0B
0K
0T
302 / 303 / 304
DCE.91.050.0VC DCE.91.050.0VM
DCC.05.02B.LAG
Male contact
FGG-EGG Crimp contacts
øA
302 / 303
DCE.91.090.BVC DCE.91.090.BVM
DCC.09.05B.LAG
DCE.91.090.AVC DCE.91.090.AVM
306 / 307 / 309
302
DCE.91.070.BVC DCE.91.070.BVM
DCE.91.050.BVC DCE.91.050.BVM
DCE.91.090.BVC DCE.91.090.BVM
DCE.91.070.BVC DCE.91.070.BVM
øA
øA
DCC.05.02B.LAG
DCC.09.05B.LAG
EGG
1S
2B
2K
2T
øC
Fig. 2
øA
øC
FGG-EGG Insulators
DCC.07.04B.LAG
302 / 303
DCE.91.131.BVC DCE.91.131.BVM
DCC.13.15B.LAG
304 / 305
DCE.91.091.BVC DCE.91.091.BVM
DCC.09.05B.LAG
306 / 307 / 308
DCE.91.071.BVC DCE.91.071.BVM
DCC.07.04B.LAG
310 / 314 / 316
DCE.91.051.BVC DCE.91.051.BVM
DCC.05.02B.LAG
302
DCE.91.131.BVC DCE.91.131.BVM
DCC.13.15B.LAG
304
DCE.91.091.BVC DCE.91.091.BVM
DCC.09.05B.LAG
302
DCE.91.202.BVCM
DCC.20.25B.LAG
303
DCE.91.162.BVCM
EGG
male
308 / 310
DCE.91.132.BVC DCE.91.132.BVM
DCC.16.25B.LAG
DCC.13.15B.LAG
female
Note: each insulator can be used both for crimp contacts of normal shape (fig. 1) or with reduced crimp
barrel (fig. 2).
DCE Positioners ø 0.5-0.7-0.9-1.3 mm 1)
male
304 / 305
306 / 307
øC
Note: a wide variation of strand number and diameter
combinations are quoted as being AWG, some of which
do not have a large enough cross section to guarantee
a crimp as per either MIL-C-22520/1-01 or /7-01.
FGG
1B
1K
1T
øC
FGG
DCC.07.04B.LAG
DCE.91.090.AVC DCE.91.090.AVM
303 / 304
Fig. 1
FGG
EGG
304 / 305
0S
Female contact
Extractors part
number for male/
female contacts
female
These positioners are suitable for use with both manual
and pneumatic crimping tools according to the MIL-C22520/7-01 standard.
DCE Turret for ø 1.6-2.0-3.0-4.0 mm 1)
DCE.91.132.CVC DCE.91.132.CVM
DCE.91.092.BVC DCE.91.092.BVM
DCC.09.05B.LAG
DCE.91.092.AVC DCE.91.092.AVM
312 / 314 / 316
318 / 319
DCE.91.072.BVC DCE.91.072.BVM
Note: 1) please consult page 132 for the corresponding crimping tools.
DCC.07.04B.LAG
Note: these turrets can be used with manual crimping
tool according to MIL-C-22520/1-01 standard.
DCC Manual extractors
www.lemo.com
129
®
®
Spare parts for crimp contacts
2S
3B
3K
3T
306
–
Female contact
–
A
C
min. max.
Contact part number
Male
Female
1.40 1 20 18
FGG.2B.565.ZZC EGG.2B.665.ZZM
1.3 1.10 2
24 20
FGG.2B.566.ZZC EGG.2B.666.ZZM
0.80 2 26 22
FGG.2B.567.ZZC EGG.2B.667.ZZM
FGG.3B.302.YL EGG.3B.402.YL
3.0 3.20 1
14 10
FGG.3B.580.ZZC EGG.3B.680.ZZM
303 / 304 / 309
FGG.3B.30l.YL 1) EGG.3B.40l.YL 1)
2.40 1 16 12
2.0
1.90 2 18 14
FGG.3B.575.ZZC EGG.3B.675.ZZM
FGG.3B.30l.YL EGG.3B.40l.YL
1.90 1 18 14
1.6
1.40 2 22 18
FGG.3B.570.ZZC EGG.3B.670.ZZM
FGG.3B.565.ZZC EGG.3B.665.ZZM
FGG.3B.3ll.YL 1) EGG.3B.4ll.YL 1)
1.40 1 20 18
1.3 1.10 2 24 20
0.80 2 26 22
FGG.3B.567.ZZC EGG.3B.667.ZZM
FGG.3B.560.ZZC EGG.3B.660.ZZM
FGG.3B.3ll.YL EGG.3B.4ll.YL
1.10 1 24 20
0.9 0.80 2 26 22
0.45 2 32 28
FGG.3B.562.ZZC EGG.3B.662.ZZM
320 / 322 / 324
326 / 330
FGG.3B.3ll.YL EGG.3B.4ll.YL
0.80 1 26 22
0.7
0.45 2 32 28
FGG.3B.555.ZZC EGG.3B.655.ZZM
304
FGG.4B.304.YL EGG.4B.404.YL
3.0 3.20 1
14 10
FGG.4B.580.ZZC EGG.4B.680.ZZM
306 / 307
FGG.4B.30l.YL EGG.4B.40l.YL
2.40 1 16 12
2.0
1.90 2 18 14
FGG.4B.575.ZZC EGG.4B.675.ZZM
310
FGG.4B.310.YL EGG.4B.410.YL
1.90 1 18 14
1.6
1.40 2 22 18
FGG.4B.570.ZZC EGG.4B.670.ZZM
FGG.4B.312.YL EGG.4B.412.YL
1.40 1 20 18
1.3
1.10 2 24 20
FGG.4B.565.ZZC EGG.4B.665.ZZM
316 / 320
324 / 330
FGG.4B.3ll.YL EGG.4B.4ll.YL
1.10 1 24 20
0.9
0.80 2 26 22
FGG.4B.560.ZZC EGG.4B.660.ZZM
340 / 348
FGG.4B.3ll.YL EGG.4B.4ll.YL
0.80 1 26 22
0.7
0.45 2 32 28
FGG.4B.555.ZZC EGG.4B.655.ZZM
304
FGG.5B.304.ML EGG.5B.404.ML
4.0 4.00 1
12 10
FGG.5B.582.ZZC EGG.5B.682.ZZM
310
FGG.5B.310.YL EGG.5B.410.YL
3.0 3.20 1
14 10
FGG.5B.580.ZZC EGG.5B.680.ZZM
314 / 316
FGG.5B.3ll.YL EGG.5B.4ll.YL
2.40 1 16 12
2.0
1.90 2 18 14
FGG.5B.575.ZZC EGG.5B.675.ZZM
320
FGG.5B.320.YL EGG.5B.420.YL
1.90 1 18 14
1.6
1.40 2 22 18
FGG.5B.570.ZZC EGG.5B.670.ZZM
FGG.5B.3ll.YL EGG.5B.4ll.YL
1.40 1 20 18
1.3 1.10 2 24 20
FGG.5B.565.ZZC EGG.5B.665.ZZM
330 / 340 / 348
0.80 2 26 22
FGG.5B.567.ZZC EGG.5B.667.ZZM
1.10 1 24 20
0.9
0.80 2 26 22
FGG.5B.560.ZZC EGG.5B.660.ZZM
308 / 309 / 310
312 / 314
316 / 318
312
5B
5K
Male contact
Cond. AWG
302
305 / 306 / 307
4B
4K
ø (mm)
Fig.
Insulator part number
Types
350 / 354 / 364
FGG.5B.3ll.YL EGG.5B.4ll.YL
FGG.3B.576.ZZC EGG.3B.676.ZZM
FGG.3B.571.ZZC EGG.3B.671.ZZM
FGG.3B.566.ZZC EGG.3B.666.ZZM
FGG.3B.561.ZZC EGG.3B.661.ZZM
FGG.3B.556.ZZC EGG.3B.656.ZZM
FGG.4B.576.ZZC EGG.4B.676.ZZM
FGG.4B.571.ZZC EGG.4B.671.ZZM
FGG.4B.566.ZZC EGG.4B.666.ZZM
FGG.4B.561.ZZC EGG.4B.661.ZZM
FGG.4B.556.ZZC EGG.4B.656.ZZM
FGG.5B.576.ZZC EGG.5B.676.ZZM
FGG.5B.571.ZZC EGG.5B.671.ZZM
FGG.5B.566.ZZC EGG.5B.666.ZZM
FGG.5B.561.ZZC EGG.5B.661.ZZM
Note: 1) for 309 type the insulator part number is FGG.3B.309.ML (male contact) and EGG.3B.409.ML (female contact).
130
www.lemo.com
®
®
Tools for crimp contacts
Positioners part number 1)
Types
2S
306
Male contact
Female contact
DCE.91.132.BVC DCE.91.132.BVM
Extractors part
number for male/
female contacts
DCC.13.15B.LAG
302
Fig. 1
øC
FGG
øA
DCC.30.35B.LAG
øA
øC
Fig. 2
øC
303 / 304 / 309
DCE.91.203.BVCM
DCC.20.25B.LAG
305 / 306 / 307
DCE.91.163.BVCM
DCC.16.25B.LAG
308 / 309 / 310
DCE.91.133.BVC DCE.91.133.BVM
DCC.13.15B.LAG
Note: a wide variation of strand number and diameter
combinations are quoted as being AWG, some of which
do not have a large enough cross section to guarantee
a crimp as per either MIL-C-22520/1-01 or /7-01.
312 / 314
316 / 318
DCE.91.093.BVC DCE.91.093.BVM
DCC.09.05B.LAG
FGG-EGG Insulators
320 / 322 / 324
326 / 330
4B
4K
DCE.91.303.BVCM
øA
EGG
DCE.91.132.CVC DCE.91.132.CVM
3B
3K
3T
FGG-EGG Crimp contacts
DCE.91.093.BVG 2) DCE.91.093.BVU 2)
FGG
EGG
øA
FGG
DCE.91.073.BVC DCE.91.073.BVM
DCC.07.04B.LAG
304
DCE.91.304.BVCM
DCC.30.35B.LAG
306 / 307
DCE.91.204.BVCM
DCC.20.25B.LAG
310
DCE.91.164.BVCM
DCC.16.25B.LAG
øC
EGG
male
female
Note: each insulator can be used both for crimp contacts of normal shape (fig. 1) or with reduced crimp
barrel (fig. 2).
DCE Positioners ø 0.5-0.7-0.9-1.3 mm 1)
5B
5K
312
DCE.91.134.BVC DCE.91.134.BVM
DCC.13.15B.LAG
316 / 320
324 / 330
DCE.91.094.BVC DCE.91.094.BVM
DCC.09.05B.LAG
340 / 348
DCE.91.074.BVC DCE.91.074.BVM
DCC.07.04B.LAG
304
DCE.91.405.BVCM
DCC.40.45B.LAG
310
DCE.91.305.BVCM
DCC.30.35B.LAG
314 / 316
DCE.91.205.BVCM
DCC.20.25B.LAG
320
DCE.91.165.BVCM
DCC.16.25B.LAG
330 / 340 / 348
DCE.91.135.BVC DCE.91.135.BVM
DCE.91.095.BVC DCE.91.095.BVM
female
These positioners are suitable for use with both manual
and pneumatic crimping tools according to the MIL-C22520/7-01 standard.
DCE Turret for ø 1.6-2.0-3.0-4.0 mm 1)
DCC.13.15B.LAG
Note: these turrets can be used with manual crimping
tool according to MIL-C-22520/1-01 standard.
DCE.91.135.BVG DCE.91.135.BVU
350 / 354 / 364
male
DCC.09.05B.LAG
DCC Manual extractors
Note:
1) please consult page 132 for the corresponding crimping tools.
2) «G» and «U» positioners for reduced crimp barrel (see p. 65 - fig. 2 for contact type details).
www.lemo.com
131
®
®
Crimping tools for electrical contacts
Manual crimping tools
Fig. A
Part number
Fig. B
contact ø 0.5-0.7 contact ø 1.6-2.0 contact ø 3.0-4.0
0.9-1.3 (Fig. A)
(Fig. B)
(Fig. B)
DPC.91.701.V1) DPC.91.101.A2) DPC.91.102.V
MH8601)
AF82)
6163361)
6157082)
1)
2)
M300BT
–
Supplier
LEMO
DANIELS
ASTRO
According to specification MIL-C-22520/7-01.
According to specification MIL-C-22520/1-01.
Pneumatic crimping tools
Part number
Supplier
DPC.91.701.C
LEMO
85230
BALMAR
621101
BUCHANAN
According to specification MIL-C-22520/7-01.
For LEMO contacts ø 0.5-0.7-0.9-1.3 mm
132
www.lemo.com
®
®
Spare parts
GBA Locking washers
Part number
GBA.00.250.FN
øA
L
øC
GBA.0S.250.FN
GBA.1S.250.FN
GBA.0E.250.FN
GBA.1E.250.FN
GBA.2S.250.FN
GBA.3S.250.FN
GBA.4S.250.FN
GBB Tapered washers
Part number
GBB.00.250.LN
øA
L
øC
GBB.0S.250.LN
GBB.1S.250.LN
GBB.2S.250.LN
GBB.3S.250.LN
GBB.4S.250.LN
GBB.5S.250.LN
0S-0B-0T
1S-1B-1T
XB
1E-1K
2S-2B-2T
3S-3B-3T
4S-4B
A
9.5
C
L
7.1
1.0
16.0 12.1
1.0
12.5
9.1
19.6 14.1
21.8 16.1
19.5 15.1
25.0 18.1
32.0 25.1
1.0
1.2
1.2
1.2
1.4
1.4
Series
00
Dimensions (mm)
A
7.1
2.0
15
12.1
3.5
22
18.1
11
2S-2B
18
3S-3B
4S-4B
5S-5B
L
9
0S-0B
1S-1B
C
28
40
9.1
15.1
25.2
35.2
2.5
4.0
4.5
5.0
7.5
Note: sockets of series 5B and 5S are always supplied with a tapered
washer. To order this accessory separately, use the above part numbers.
The panel cut out diameters are larger when using tapered washer.
l Material: Nickel-plated brass (3 µm)
GEG Notched nut
Part number
øA
L
e
GEG.00.240.LC
øB
GEG.0S.240.LC
GEG.0E.240.LC
GEG.1S.240.LC
Model 1
GEG.1E.240.LC
GEG.1S.242.LC
GEG.2S.240.LC
øA
L
e
GEG.2S.241.LC
øB
GEG.2E.240.LC
www.lemo.com
00-TT
Dimensions (mm)
Note: to order this accessory separately, use the above part numbers.
l Material: Nickel-plated bronze (3 µm)
Model 2
Series
Model
1
A
8.6
Dimensions (mm)
B
M7 x 0.5
2.5
18
M14 x 1.0
3.5
20
M16 x 1.0
10.5
12
1
14.0
16
2
1
2
2
2
15.8
17.5
12.1
17.5
20.5
22.5
L
10
1
1
e
14
20
24
25
M9 x 0.6
M12 x 1.0
M11 x 0.5
M15 x 1.0
M19 x 1.0
M20 x 1.0
l Material: Chrome-plated brass (Ni 3 µm + Cr 0.3 µm)
2.5
3.5
3.5
3.5
3.5
3.5
3.5
Note: 00, TT, 0B, 0T, 0S, 1B, 1T, 1S, 2B, 2T and 2S series fixed and
free sockets for back panel mounting are always delivered with this notched
nut. To order this accessory separately, use the above part numbers.
133
®
®
GEA Hexagonal nuts
A
Series
GEA.00.240.LN
00-TT
9
10.2
GEA.0S.240.LN
0S-0B-0T
11
GEA.0S.241.LN
0S-0B
12
0E-0K
GEA.0E.240.LN
L
øB
e
1S-1B-XB
A
B
e
L
M7 x 0.50
2.0
12.4
M9 x 0.60
2.0
13.8
M10 x 0.75
2.5
17
19.2
M14 x 1.00
2.5
GEA.1S.240.LN
1S-1B-1T
14
15.8
M12 x 1.00
2.5
GEA.1S.241.LN
1B
13
14.8
M11 x 0.50
2.5
1E-1K
19
21.5
M16 x 1.00
3.0
GEA.1E.240.LN
l Material: Nickel-plated brass (3 µm), natural anodized aluminium alloy,
stainless steel
Dimensions (mm)
Part number
2S-2B
GEA.2S.240.LN
2S-2B-2T
17
19.2
M15 x 1.00
2.7
GEA.2E.240.LN
2E-2K
24
27.0
M20 x 1.00
4.0
GEA.3S.240.LN
3S-3B-3T
22
25.0
M18 x 1.00
3.0
GEA.3E.240.LN
3E-3K
30
34.0
M24 x 1.00
5.0
GEA.4S.240.LN
4S-4B
30
34.0
M25 x 1.00
5.0
GEA.4E.240.LN
4E-4K
36
40.5
M30 x 1.00
7.0
Note: to order this part separately, use the above part numbers. The last letters «LN» of the part number refer to the nut material and treatment. If a nut
in aluminium alloy or stainless steel is desired, replace the last letters of the part number by «PT» or «AZ» respectively.
GEC Conical nuts
Part number
A
L
øB
e
l Material: Chrome-plated brass (Ni 3 µm + Cr 0.3 µm)
Note: 3B, 3K, 3T, 3S, 3E, 4B, 4K, 4S, 4E, 5B, 5K, 5S, 5E, 6S and 6E series
fixed and free sockets for back panel mounting are always delivered with
a conical nut. To order this accessory separately, use the part numbers
in the adjacent table.
134
Dimensions (mm)
A
B
e
L
GEC.00.240.LC
8
10.0
M7 x 0.5
2.5
GEC.0S.240.LC
10
12.0
M9 x 0.6
2.5
GEC.0E.240.LC
16
18.0
M14 x 1.0
3.0
GEC.1S.240.LC
13
16.0
M12 x 1.0
3.2
GEC.1S.241.LC
17
20.0
M16 x 1.0
4.0
GEC.1S.242.LC
12
14.0
M11 x 0.5
3.2
GEC.2S.240.LC
17
20.0
M15 x 1.0
3.8
GEC.2S.241.LC
20
24.0
M19 x 1.0
5.8
GEC.2E.240.LC
22
25.0
M20 x 1.0
5.0
GEC.3S.240.LC
20
24.0
M18 x 1.0
4.5
GEC.3E.240.LC
27
30.0
M24 x 1.0
4.5
GEC.4S.240.LC
27
30.0
M25 x 1.0
4.5
GEC.4K.241.LC
32
35.5
M30 x 1.0
5.0
GEC.5S.240.LC
37
41.0
M35 x 1.0
5.0
www.lemo.com
®
®
GEB Round nuts
Part number
øA
e
GEB.00.240.LN
L
GEB.0S.240.LN
GEB.0E.240.LN
GEB.1S.240.LN
GEB.1E.240.LN
Model 1
GEB.2S.240.LN
GEB.2B.240.LN
GEB.3S.240.LN
GEB.4S.240.LN
øA
e
L
GEB.5S.240.LN
GEB.5E.240.LN
GEB.6S.241.LN
GEB.6E.240.LN
Model 2
www.lemo.com
Model
1
A
Dimensions (mm)
M7 x 0.50
4.0
18.0
M14 x 1.00
5.0
20.0
M16 x 1.00
11.0
1
14.0
1
1
1
1
1
2
2
2
2
L
9.0
1
1
e
18.0
17.5
22.0
28.0
40.0
54.0
54.0
65.0
l Material: Nickel-plated brass (3 µm)
M9 x 0.60
M12 x 1.00
M15 x 1.00
M15 x 0.75
M18 x 1.00
M25 x 1.00
M35 x 1.00
M45 x 1.50
M48 x 1.50
M55 x 2.00
4.0
5.0
5.0
5.5
2.5
5.5
6.0
8.0
8.0
8.0
9.0
Note: 5B, 5K, 5S, 5E, 6S and 6E series sockets are always supplied with
model 2 round nuts. To order this accessory separately, use the part
numbers in the adjacent table.
135
®
136
®
www.lemo.com
TOOLING
ACCESSORIES
®
®
Accessories
BFG Plug caps
Dimensions (mm)
L
Part number
Series
B
øA
A
N
l
l
l
l
l
B
L N1)
BFG.00.100.PCSG
00
7.5 9.8 10.0 60
BFG.0B.100.PCZG
0S-0B
9.5 12.5 11.2 85
BFG.1B.100.PCZG
1S-1B
12.0 15.5 12.3 85
BFG.2B.100.PCSG
2S-2B
15.0 18.0 15.0 85
BFG.3B.100.PCSG
3S-3B
18.5 22.0 18.5 95
Note: 1) the tolerance on this dimension is ± 5 mm.
This cap is available only with an alignment key (G). Upon request this
cap can be supplied in black and the last letter «G» of the part number
should be replaced with «N».
Body material: Polyoxymethylene (POM) grey (or black)
Cord material: Polyamide 6, grey (or black)
Gasket material: Silicone rubber
Maximum operating temperature: 100°C
Watertightness: IP51 according to IEC 60529
Fitting the cord
Slide the plug into the loop of the cord.
Place the loop into the groove in front of the collet nut and
tighten the loop.
BFA Plug caps
Dimensions (mm)
Part number
L
A
B
L N1)
BFA.0E.100.NAS
0E
14.0
6
12.5 85
BFA.1E.100.NAS
1E
16.0
6
15.5 85
BFA.2E.100.NAS
2E
19.5
6
17.5 85
BFA.3E.100.NAS
3E
23.0
6
22.0 120
BFA.4E.100.NAS
4E
29.0 10 22.5 120
BFA.4S.100.NAS
4S
25.0 10 22.2 120
BFA.5E.100.NAS
5E
44.0 10 27.0 150
BFA.5S.100.NAS
5S
36.0 10 30.2 150
BFA.6S.100.NAS
6S
46.0 10 33.0 150
N
øA
B
Series
sliding loop
l
l
l
l
l
l
Body material: Nickel-plated brass (Ni 3µm)
Lanyard material: Stainless steel
Crimp ferrule material: Nickel-plated brass + polyolefin
O-ring material: Silicone rubber or FPM
Operating temperature: -50°/135°C (Silicone rubber & Polyolefine)
Watertightness: IP68 according to IEC 60529 for E series
138
Note: 1) the tolerance on this dimension is ± 5 mm.
The last letter «S» of the part number stands for the material of the O-ring
(silicone rubber). O-ring’s made from FPM are also available; if required,
replace the letter «S» by «V».
www.lemo.com
®
®
BFG Plug caps with key (G)
Dimensions (mm)
Part number
B
A
B
L N1)
BFG.0K.100.NAS
0K
14.0
6
12.5 85
BFG.1K.100.NAS
1K
16.0
6
15.5 85
BFG.2K.100.NAS
2K
19.5
6
17.5 85
BFG.3K.100.NAS
3K
23.0
6
22.0 120
BFG.4B.100.NAS
4B
25.0 10 20.2 120
BFG.4K.100.NAS
4K
29.0 10 22.5 120
BFG.5B.100.NAS
5B
36.0 10 27.2 150
BFG.5K.100.NAS
5K
44.0 10 27.0 150
BFG.6E.100.NAS
6E
54.0 10 31.0 150
N
øA
L
Series
sliding loop
l
l
l
l
l
l
Body material: Nickel-plated brass (Ni 3µm)
Lanyard material: Stainless steel
Crimp ferrule material: Nickel-plated brass + polyolefin
O-ring material: Silicone rubber or FPM
Operating temperature: -50°/135°C (Silicone rubber & Polyolefine)
Watertightness: IP68 according to IEC 60529 for E and K series
Note: 1) the tolerance on this dimension is ± 5 mm.
This cap is available only with an alignment key (G). The last letter «S»
of the part number stands for the material of the O-ring (silicone rubber).
O-ring’s made from FPM are also available; if required, replace the letter
«S» by «V».
BHG Plug caps, nut fixing or flange
Dimensions (mm)
Part number
B
ø 3.5
N
øA
L
l
l
l
l
l
l
Body material: Nickel-plated brass (Ni 3µm)
Lanyard material: Stainless steel
Crimp ferrule material: Nickel-plated brass + polyolefin
O-ring material: Silicone rubber or FPM
Operating temperature: -50°/135°C (Silicone rubber & Polyolefine)
Watertightness: IP68 according to IEC 60529 for E and K series
Series
A
B
L N1)
BHG.0K.100.NAS
0K
14.0
6
12.5 85
BHG.1K.100.NAS
1K
16.0
6
15.5 85
BHG.2K.100.NAS
2K
19.5
6
17.5 85
BHG.3K.100.NAS
3K
23.0
6
22.0 120
BHG.4B.100.NAS
4B
25.0 10 20.2 120
BHG.4K.100.NAS
4K
29.0 10 22.5 120
BHG.5B.100.NAS
5B
36.0 10 27.2 150
BHG.5K.100.NAS
5K
44.0 10 27.0 150
BHG.6E.100.NAS
6E
54.0 10 31.0 150
Note: 1) the tolerance on this dimension is ± 5 mm.
This cap is available only with an alignment key (G). The last letter «S»
of the part number stands for the material of the O-ring (silicone rubber).
O-ring’s made from FPM are also available; if required, replace the letter
«S» by «V».
BFG Plug cap
L
Dimensions (mm)
Series
øA
Part number
A
BFG.3K.100.EAN
N
3K
L N1)
26 31 155
l Material: black ALCRYN®
l Lanyard material: Stainless steel
l Crimp ferrule material: Stainless steel AISI 304 + polyolefin
Note: 1) the tolerance on this dimension is ± 5 mm.
These caps are suitable for use with any alignment key configuration.
www.lemo.com
139
®
®
BHA Plug cap
L
Dimensions (mm)
øA
Part number
A
BHA.3K.100.EAN
3K
L N1)
26 31 120
l Material: black ALCRYN®
l Lanyard material: Stainless steel
l Crimp ferrule material: Stainless steel AISI 304 + polyolefin
ø 3.2
N
Series
Note: 1) the tolerance on this dimension is ± 5 mm.
These caps are suitable for use with any alignment key configuration.
BRA Blanking caps for fixed sockets and free straight sockets
L
Dimensions (mm)
M
Part number
Series
B
ø 3.5
øA
A
N
l
l
l
l
l
B
L
M N1)
BRA.00.200.PCSG
00
7.5 9.8 9.0 3.5 60
BRA.0B.200.PCSG
0S-0B
10.0 12.5 11.0 4.8 60
BRA.1B.200.PCSG
1S-1B
14.0 17.0 13.5 5.6 60
BRA.2B.200.PCSG
2S-2B
18.0 21.0 14.5 6.0 60
BRA.3B.200.PCSG
3S-3B
22.0 25.5 17.0 7.0 60
Note: 1) the tolerance on this dimension is ± 5 mm.
These caps are suitable for use with any alignment key configuration. On
request this cap can be supplied in black. If so, replace the last letter «G»
of the part number by «N».
Body material: Polyoxymethylene (POM) grey (or black)
Cord material: Polyamide 6, grey (or black)
Gasket material: Silicone rubber
Maximum operating temperature: 100°C
Watertightness: IP61 according to IEC 60529
BRE Blanking caps for fixed sockets
Dimensions (mm)
Part number
Series
A
L
B
L
M N1)
BRE.00.200.NAS
00
8 7.5 8.8 3.5 60
BRE.0S.200.NAS
0S-0B
10 9.5 10.5 4.5 85
BRE.1S.200.NAS
1S-1B
14 11.0 12.5 5.0 85
BRE.2S.200.NAS
2S-2B
18 12.0 14.0 6.0 85
BRE.3S.200.NAS
3S-3B
22 14.0 18.0 8.0 120
BRE.4S.200.NAS
4S-4B
28 20.0 23.0 10.0 120
BRE.5S.200.NAS
5S-5B
40 22.0 30.0 12.0 150
BRE.6S.200.NAS
6S
54 22.0 30.0 12.0 150
BRE.6E.200.NAS
6E
57 24.0 31.5 14.0 150
N
øA
M
B
ø 3.5
l
l
l
l
l
l
Body material: Nickel-plated brass (Ni 3 µm)
Lanyard material: Stainless steel
Crimp ferrule material: Nickel-plated brass + polyolefin
O-ring material: Silicone rubber or FPM
Operating temperature: -50°/135°C (Silicone rubber & Polyolefine)
Watertightness: IP61 according to IEC 60529 for S series
140
Note: 1) the tolerance on this dimension is ± 5 mm.
These caps are suitable for use with any alignment key configuration. The
last letter «S» of the part number stands for the O-ring material (silicone
rubber). O-ring’s made from FPM are also available; if required, replace
the letter «S» by «V».
www.lemo.com
®
®
BRE Blanking caps for fixed sockets
L
B
Dimensions (mm)
Part number
M
A
ø 3.5
N
øA
l
l
l
l
l
l
Series
Body material: Nickel-plated brass (Ni 3 µm)
Lanyard material: Stainless steel
Crimp ferrule material: Nickel-plated brass + polyolefin
O-ring material: Silicone rubber or FPM
Operating temperature: -50°/135°C (Silicone rubber & Polyolefine)
Watertightness: IP68 according to IEC 60529
B
L
M N1)
BRE.0K.200.NAS
0K-0E
15.0 10 15.0
4
85
BRE.1K.200.NAS
1K-1E
17.0 12 20.0
6
85
BRE.2K.200.NAS
2K-2E
20.5 14 24.0
8
85
BRE.3K.200.NAS
3K-3E
24.0 14 28.0
8
120
BRE.4K.200.NAS
4K-4E
30.0 20 30.5 10 120
BRE.5K.200.NAS
5K-5E
44.0 22 37.0 12 150
Note: 1) the tolerance on this dimension is ± 5 mm.
These caps are suitable for use with any alignment key configuration. The
last letter «S» of the part number stands for the O-ring material (silicone
rubber). O-ring’s made from FPM are also available; if required, replace
the letter «S» by «V».
BRA Blanking caps for fixed sockets
L
M
Dimensions (mm)
Part number
Series
ø 3.2
øA
A
L
M N1)
BRA.3K.200.EAN
3K
26 27 14.5 120
BRA.4K.200.EAN
4K
31 31 17.0 120
l Material: black ALCRYN®
l Lanyard material: Stainless steel
l Crimp ferrule material: Stainless steel AISI 304 + polyolefin
N
Note: 1) the tolerance on this dimension is ± 5 mm.
These caps are suitable for use with any alignment key configuration.
BRF Blanking caps for free sockets
L
M
Dimensions (mm)
Part number
Series
øA
A
BRF.3K.200.EAN
N
3K
L
M N1)
26 27 14.5 155
l Material: black ALCRYN®
l Lanyard material: Stainless steel
l Crimp ferrule material: Stainless steel AISI 304 + polyolefin
Note: 1) the tolerance on this dimension is ± 5 mm.
These caps are suitable for use with any alignment key configuration.
www.lemo.com
141
®
®
BRD Blanking caps for free sockets
L
M
Dimensions (mm)
Part number
Series
B
øA
A
N
l
l
l
l
l
B
L
M N1)
BRD.00.200.PCSG
00
BRD.0B.200.PCSG
0S-0B
BRD.1B.200.PCSG
1S-1B
14.0 17.0 13.5 5.6
85
BRD.2B.200.PCSG
2S-2B
18.0 21.0 14.5 6.0
85
BRD.3B.200.PCSG
3S-3B
22.0 25.5 17.0 7.0
95
7.5 9.8 9.0 3.5 85
10.0 12.5 11.0 4.8
85
Note: 1) the tolerance on this dimension is ± 5 mm.
On request this cap is available in black. If required, replace the last letter
«G» of the part number by «N».
Body material: Polyoxymethylene (POM) grey (or black)
Cord material: Polyamide 6, grey (or black)
Gasket material: Silicone rubber
Maximum operating temperature: 100°C
Watertightness: IP61 according to IEC 60529
Fitting the cord
Slide the socket into the loop of the cord.
Place the loop into the groove in front of the collet nut.
Tighten the loop.
BRF Blanking caps for free sockets
Dimensions (mm)
Part number
L
A
B
N
øA
M
sliding loop
l
l
l
l
l
l
Body material: Nickel-plated brass (Ni 3 µm)
Lanyard material: Stainless steel
Crimp ferrule material: Nickel-plated brass + polyolefin
O-ring material: Silicone rubber or FPM
Operating temperature: -50°/135°C (Silicone rubber & Polyolefine)
Watertightness: IP61 according to IEC 60529 for S series
142
Series
B
L
M N1)
BRF.00.200.NAS
00
8 7.5 8.8 3.5 85
BRF.0S.200.NAS
0S-0B
10 9.5 10.5 4.5 85
BRF.1S.200.NAS
1S-1B
14 11.0 12.5 5.0 85
BRF.2S.200.NAS
2S-2B
18 12.0 14.0 6.0 85
BRF.3S.200.NAS
3S-3B
22 14.0 18.0 8.0 120
BRF.4S.200.NAS
4S-4B
28 20.0 23.0 10.0 120
BRF.5S.200.NAS
5S-5B
40 22.0 30.0 12.0 150
BRF.6S.200.NAS
6S
54 22.0 30.0 12.0 150
Note: 1) the tolerance on this dimension is ± 5 mm.
These caps are suitable for use with any alignment key configuration. The
last letter «S» of the part number stands for the O-ring material (silicone
rubber). O-ring’s made from FPM are also available; if required, replace
the letter «S» by «V».
www.lemo.com
®
®
BRF Blanking caps for free sockets
L
Dimensions (mm)
B
Part number
Series
A
B
L
M N1)
BRF.0K.200.NAS
0K-0E
15.0 10 15.0
4
85
BRF.1K.200.NAS
1K-1E
17.0 12 20.0
6
85
BRF.2K.200.NAS
2K-2E
20.5 14 24.0
8
85
BRF.3K.200.NAS
3K-3E
24.0 14 28.0
8
120
BRF.4K.200.NAS
4K-4E
30.0 20 30.5 10 120
BRF.5K.200.NAS
5K-5E
44.0 22 37.0 12 150
N
øA
M
sliding loop
l
l
l
l
l
l
Body material: Nickel-plated brass (Ni 3 µm)
Lanyard material: Stainless steel
Crimp ferrule material: Nickel-plated brass + polyolefin
O-ring material: Silicone rubber or FPM
Operating temperature: -50°/135°C (Silicone rubber & Polyolefine)
Watertightness: IP68 according to IEC 60529
Note: 1) the tolerance on this dimension is ± 5 mm.
These caps are suitable for use with any alignment key configuration. The
last letter «S» of the part number stands for the O-ring material (silicone
rubber). O-ring’s made from FPM are also available; if required, replace
the letter «S» by «V».
BRR Spring loaded dust caps for ERA, ERN and EGl sockets or PSA and PKl fixed sockets
Dimensions (mm)
Part number
Series
A B C E L M N
N
L
øC
B
øA
BRR.0S.200.PZVG
0S-0B
11.0 13.3 9.0 5.8 5.0 1.2 15.3
BRR.1S.200.PZVG
1S-1B
14.2 17.1 12.0 6.0 6.3 1.5 20.3
BRR.2S.200.PZVG
2S-2B
18.6 22.4 15.2 6.5 8.2 2.0 26.2
BRR.3S.200.PZVG
3S-3B
22.5 26.5 18.2 9.0 8.8 2.5 30.8
Note: On request, this cap is available in black, blue or white. If so
replace the last letter «G» of the part number by «N», «A» or «B».
l
l
l
l
l
l
M
E maxi
Body material: PSU
Gasket material: FKM
Spring material: Stainless steel
Axes material: Nickel-plated brass
Maximum operating temperature: 100°C
Watertightness: IP61 according to IEC 60529
BRR Spring loaded dust cap for EDl and EBl fixed sockets
Dimensions (mm)
Part number
N
A B C L M N
L
øA
Series
BRR.3K.200.PZSG
3K
29 29 23 8.1 3 33.2
øC
B
Note: Use Allen key (0.9 mm flat) to secure cap on connector.
M
www.lemo.com
l
l
l
l
l
l
l
Cap material: Polyoxymethylene (POM) grey
Body material: Nickel-plated brass
Gasket material: Silicone rubber
Spring material: Stainless steel
Axes material: Nickel-plated brass
Maximum operating temperature: 100°C
Watertightness: IP61 according to IEC 60529
143
®
®
BFG Blanking caps for plugs (T series)
BHG Blanking caps for fixed plugs (T series)
L
B
L
N
N
øA
øA
B
ø 3.5
sliding loop
Dimensions (mm)
Part number
A
B
L N1)
Part number
BFG.TT.100.CAS
7.0 4.3 9.0 60
BHG.TT.100.CAS
BFG.0T.100.CAS
9.5 5.0 11.0 85
BHG.0T.100.CAS
BFG.1T.100.CAS
12.0 6.3 12.4 85
BHG.1T.100.CAS
BFG.2T.100.CAS
15.0 6.4 13.8 85
BHG.2T.100.CAS
BFG.3T.100.CAS
18.8 6.4 17.6 120
BHG.3T.100.CAS
l
l
l
l
l
l
Note: 1) the tolerance on this dimension is ± 5 mm.
BRF Blanking caps for free sockets (T series)
B
Body material: Chrome-plated brass (Ni 3 µm)
Lanyard material: Stainless steel
Crimp ferrule material: Nickel-plated brass + polyolefin
O-ring material: Silicone
Operating temperature: -50°/135°C (Silicone rubber & Polyolefine)
Watertightness: IP68 according to IEC 60529
BRE Blanking caps for sockets (T series)
B
L
øA
øA
L
M
N
N
M
ø 3.5
sliding loop
Dimensions (mm)
Part number
A
B
L
M N1)
Part number
BRF.TT.200.CAZ
7.0 4.3 10.4 2.4 60
BRE.TT.200.CAZ
BRF.0T.200.CAZ
9.5 5.0 13.2 3.2 85
BRE.0T.200.CAZ
BRF.1T.200.CAZ
12.0 6.3 15.1 4.2
85
BRE.1T.200.CAZ
BRF.2T.200.CAZ
15.0 6.4 17.1 5.2
85
BRE.2T.200.CAZ
BRF.3T.200.CAZ
18.8 6.4 21.2 6.4 120
BRE.3T.200.CAZ
144
l
l
l
l
l
Body material: Chrome-plated brass (Ni 3 µm)
Lanyard material: Stainless steel
Crimp ferrule material: Nickel-plated brass + polyolefin
Operating temperature: -50°/135°C (Silicone rubber & Polyolefine)
Watertightness: IP68 according to IEC 60529
Note: 1) the tolerance on this dimension is ± 5 mm.
www.lemo.com
®
®
GMl
Bend relief (TPU)
A bend relief made from thermoplastic polyurethane elastomer can be fitted over LEMO plugs and sockets that are
supplied with nut for fitting such bend relief.
They are available in nine different colours match with the
GRA insulating washers (see page 149).
Use the part numbers shown below to order this accessory
separately.
øA
L
Main characteristics
l Material: TPU (Thermoplastic Polyurethane)
l Temperature range in dry atmosphere: -40°C
Bend relief
+80°C
Cable ø
Series
Part number
Bend relief
A
L
min.
max.
GMA.00.012.DG 1)
1.2
22
1.1
1.4
GMA.2B.040.DG
GMA.00.018.DG
1)
1.8
22
1.8
2.1
GMA.2B.045.DG
GMB.00.025.DG
1)
2.5
22
2.5
2.8
GMA.2B.050.DG
GMB.00.028.DG 1)
2.8
22
2.8
3.1
GMA.2B.060.DG
00-TT
2B
2S
2E-2K-2T
3.2
22
3.2
3.5
GMA.2B.070.DG
GMD.00.025.DG 1)
2.5
22
2.5
2.8
GMA.2B.080.DG 1)
GMD.00.028.DG
1)
2.8
22
2.8
3.1
GMA.3B.050.DG 1)
GMD.00.032.DG
1)
3.2
22
3.2
3.5
GMA.3B.060.DG
GMB.00.032.DG 1)
GMA.0B.025.DG
2.5
GMA.0B.030.DG
0B
GMA.0B.035.DG
GMA.0B.040.DG
1)
GMA.0B.045.DG
1)
3.0
24
24
2.5
3.0
2.9
3.4
3E-3K-3T
GMA.3B.080.DG
4S
3.5
3.9
GMA.3B.090.DG
0E-0K-0T
4.0
24
4.0
4.4
GMA.4B.080.DG 1)
GMA.1B.030.DG
3.0
24
30
30
4.5
2.5
3.0
5.2
GMA.4B.010.DG 1)
2.9
GMA.4B.011.DG
1)
3.4
GMA.4B.012.DG
1)
GMA.4B.013.DG
1)
GMA.1B.035.DG
1B-XB
3.5
30
3.5
3.9
GMA.1B.040.DG
1S
4.0
30
4.0
4.4
GMA.1B.045.DG
1E-1K-1T
4.5
30
4.5
4.9
5.4
30
5.4
6.0
6.5
30
6.5
7.0
GMA.1B.065.DG
GMA.3B.070.DG
24
2.5
1)
3B
3.5
GMA.1B.025.DG
GMA.1B.054.DG
3S
0S
4.5
Cable ø
Series
Part number
4S
4B
4E-4K
5E-5K
A
L
min.
max.
4.0
36
4.0
4.5
4.5
36
4.5
5.0
5.0
36
5.0
5.5
6.0
36
6.0
6.5
7.0
36
7.0
7.7
7.8
36
7.8
8.8
4.5
42
4.5
5.2
6.0
42
6.0
6.9
7.0
42
7.0
7.9
8.0
42
8.0
8.9
9.0
42
9.0
10.0
8.0
60
8.0
9.0
10.0
60
10.0
10.9
11.0
60
11.0
11.9
12.0
60
12.0
13.0
13.5
60
13.5
14.5
Note: all dimensions are in millimetres.
Note: 1) Design may differ from other bend relief, model without stripes. The «GMD» are thin bend reliefs (for very flexible cables).
The last letter «G» of the part number indicates the grey colour of the bend relief. For ordering a bend relief with another colour, see table on page 146
and replace the letter «G» by the letter of the required colour. See also detailed information for each series: B series on page 71; K series on page 71;
T series on page 71; S series on page 121; E series on page 121.
www.lemo.com
145
®
®
GMA Bend relief (Silicone)
A bend relief has been designed for connectors used in
applications at high temperature or requiring vapour sterilization.
These bend reliefs are different from previous ones as for
their material, a silicone elastomer which is noted for its
retention of flexibility over a wide temperature range. They
are available in nine colours.
Use the part numbers shown below to order this accessory
separately.
øA
L
Main characteristics
l Material: Silicone elastomer VMQ
l Temperature range in dry atmosphere: -60°C
l Temperature range in water steam: +140°C
Part number
Series
Bend relief
Cable ø
Part number
L
min. max.
1.7
27
1.7 2.4
GMA.2B.040.RG
2.5
27
2.5 2.9
GMA.2B.045.RG
3.0
27
3.0 3.4
GMA.2B.051.RG
3.5
27
3.5 3.9
GMA.2B.057.RG
4.0
27
4.0 4.4
GMA.0B.045.RG
4.5
27
GMA.1B.025.RG
2.5
GMA.1B.030.RG
GMA.0B.018.RG
GMA.0B.025.RG
GMA.0B.030.RG
GMA.0B.035.RG
GMA.0B.040.RG
0B
0S
0E-0K-0T
GMA.1B.035.RG
GMA.1B.040.RG
GMA.1B.045.RG
GMA.1B.051.RG
1B
1S
1E-1K-1T
A
+200°C
Series
Bend relief
L
min. max.
4.0
41
4.0 4.4
4.5
41
4.5 5.0
2B
5.1
41
5.1 5.6
2S
5.7
41
5.7 6.2
GMA.2B.063.RG
2E-2K-2T 6.3
41
6.3 7.0
4.5 5.2
GMA.2B.071.RG
7.1
41
7.1 7.9
34
2.5 2.9
GMA.2B.080.RG
8.0
41
8.0 9.0
3.0
34
3.0 3.4
3.5
34
3.5 3.9
4.0
34
4.0 4.4
4.5
34
4.5 5.0
5.1
34
5.1 5.6
GMA.1B.057.RG
5.7
34
5.7 6.2
GMA.1B.063.RG
6.3
34
6.3 7.0
A
Cable ø
Note: The last letter «G» of the part number indicates the grey colour of the bend relief. For ordering a bend relief with another colour, see table on page
146 and replace the letter «G» by the letter of the required colour. See also detailed information for each series: B series on page 71; K series on page
71; T series on page 71; S series on page 121; E series on page 121.
Note: the selection of pigments, which should remain
stable at high temperature, is limited by the new regulations. For this reason, some colours will be a shade
different from those used for Thermoplastic Polyurethane
(TPU) bend reliefs. The selected solutions represent the
best possible compromise.
146
Ref.
Colour
Ref.
Colour
Ref.
Colour
A
blue
J
yellow
R
red
B
white
M
brown
S
orange
G
grey
N
black
V
green
www.lemo.com
®
®
GMl
Overall bend relief for plugs and sockets
GMF
Bend relief for straight plug
Overall bend reliefs, type GMF for plugs and GMP for sockets offer optimum protection against mechanical damage and
give a protection index of IP65 according to IEC 60529 (mated position). These bend reliefs slide easily over the connector
shell and are positioned by slightly pressing the bend relief backnut.
The special design of the bend relief for plug provides for easy use of the push-pull self-latching system.
Part number
L
GMF.0B.035.060EN
øA
GMF.1B.062.072EN
GMP
GMF.2B.082.095EN
Series
Bend relief
A
Part number
L
GMP.0B.035.069EN
øA
GMP.1B.062.079EN
GMP.2B.082.102EN
min.
max.
72.0
2.5
6.2
11.0
60.5
2S-2B
22.0
95.0
16.0
l Material: Elastomer rubber black colour
l Operating temperature: -30°C to +120°C
Bend relief for free socket
L
0S-0B
1S-1B
Series
Bend relief
A
8.2
Cable ø
max.
80.0
2.5
6.2
69.0
2S-2B
21.0
102.5
l Material: Elastomer rubber black colour
l Operating temperature: -30°C to +120°C
5.0
3.5
min.
11.0
16.0
1.0
L
0S-0B
1S-1B
Cable ø
1.0
5.0
3.5
8.2
– The overall bend relief shall be installed over plug or free socket fitted with a nut for bend relief.
– The typical applications are shown below.
– The overall bend relief can be cut at different length depending on cable diameter.
Plug-free socket
Plug-fixed socket
Optimum protection is offered only when using
front panel mounting fixed sockets
www.lemo.com
PCA
FFA
S series
PHG
FGG
B series
ERA
FFA
S series
EGG
FGG
B series
147
®
®
GMF
Bend relief with cap for plug
Part number
For
models
Cut
4E
FFA
A
35
ø 31
ø 31
ø
131
Series
160
Bend relief with cap for free socket
Part number
ø 31
ø 35
GSC Lead-through with cable collet
~L
S3
GSC.00.290.CDll
M
øA
e
øB
GSC.1S.290.NDll
E maxi
148
S1
S2
GSC.3S.290.NDll
14.9
Cut
4E
PCA
A
4K
PHG
A
6.5
B
8.1
12.0 12.5
min.
max.
9.0
9.9
8.0
8.9
B
10.0
11.4
D
13.0
14.9
C
11.5
E
E
16.5
admissible ø (mm)
12.9
15.0
Dimensions (mm)
e
12.9
15.0
–
l Material: Black EPDM
Part number
13.0
For
models
AB C D E
160
D
E
GMP.4K.080.EANZ
9.9
8.9
11.5
Series
17
9.0
8.0
11.4
FGG
ø
156
max.
10.0
4K
l Material: Black EPDM
min.
B
C
GMF.4K.080.EANZ
AB C D E
GMP
–
admissible ø (mm)
L
M5x0.5 1.5 16
M9x0.6 5.0 26
M
4.0
16.5
S1 S2 S3
5
7.5 11
17.0 19.5 M15x1.0 8.1 30 12.0
–
6
9
7
11
14 17
Note: ll = collet cable diameter of the B series. For cable diameter refer
to page 67. Other surface treatment available.
The cable collet system stands for both screened and unscreened cables.
It can be delivered with a nut for fitting a bend relief it you add a «Z» at
the end of the part number.
www.lemo.com
®
®
GCA Earthing washer
Dimensions (mm)
Part number
Series
A
GCA.00.255.LT
GCA.0S.255.LT
GCA.0E.255.LT
øA
L
øB
GCA.1S.255.LT
GCA.1E.255.LT
N
GCA.2S.255.LT
GCA.2E.255.LT
GCA.3S.255.LT
00-TT
B
L
N
9.5 7.1 0.4 18.2
0S-0B-0T 13.0 9.1 0.4 22.0
0E-0K
17.0 14.1 0.5 27.5
1S-1B-1T 17.0 12.2 0.5 27.5
20.0 16.2 0.5 32.0
1E-1K
2S-2B-2T 20.0 15.2 0.5 32.0
25.0 20.2 0.5 39.0
2E-2K
3S-3B-3T 25.0 18.2 0.5 39.0
GCA.3E.255.LT
3E-3K
31.0 24.0 0.5 43.0
GCA.4S.255.LT
4S-4B
35.0 25.6 0.6 50.0
GCA.4E.255.LT
4E-4K
35.0 30.6 0.6 50.0
GCA.5S.255.LT
5S-5B
42.0 35.1 0.3 57.5
l Material: CuSnZn plated brass (2 µm)
GRA Insulating washers
Sockets or plugs mounted on panels can be fitted with insulating washers. The nine colours available combined with those
for the bend reliefs makes colour coding possible.
Dimensions (mm)
Part number
Series
A B E L M S T
GRA.00.269.GG
00
10.0 8.8 4.5 1.8 1.0 6.4 8.0
GRA.0S.269.GG
0S-0B
12.0
10.8 6.0 1.8 1.0 8.3 9.9
GRA.1S.269.GG
1S-1B
16.0 13.8 6.5 1.8 1.0 10.6 12.2
GRA.2S.269.GG
2S-2B
21.1 17.9 7.3 2.3 1.3 13.6 16.2
GRA.3S.269.GG
3S-3B
25.0 21.8 10.3 2.2 1.2 16.7 20.2
GRA.4S.269.GG
4S-4B
31.9 28.7 10.5 2.5 1.5 23.6 27.1
Note: insulating washers for series 5B are available on request.
Caution: these insulating washers can be used with fixed and free sockets
with across flat dimension S1 equivalent to the S dimension of the washer.
L
M
øA
l Material: Polyamide
l Maximum operating temperature: 90° C
S
øB
Ref.
E maxi
T
Colour
Ref.
Colour
Ref.
Colour
A
blue
J
yellow
R
red
B
white
M
brown
S
orange
G
grey
N
black
V
green
Note: the last letter «G» of the part number indicates the colour grey for
the insulating washer. To obtain an insulating washer of another colour,
refer to the table above and change the letter «G» of the part number to
the corresponding letter of the colour required. For the panel cut-out,
please consult chapter «Panel cut-out» on page 158.
www.lemo.com
149
®
®
GRC Double panel washers
Double panel washers have been designed to make the drilling of panel holes easier for mounting fixed and free sockets.
The combination of the nine different colours of the double panel washers and of the bend reliefs makes colour coding
possible.
Part number
GRC.0S.260.HG
GRC.1B.260.HG
Series
0S-0B
1S-1B
B
Dimensions (mm)
E H
L
M
N
R
S
10.9 5 14 2.5 1.5 26.5 12.5 8.3
13.9 5 20 3.3 1.8 34.5 14.5 10.6
Caution: these double panel washers can be used with fixed or free sockets with across flat dimension S1 equivalent to the S dimension of the
washer.
l Material: Polyamide
l Maximum operating temperature: 90° C
L
Ref.
R
M
A
S
B
øB
H
N
G
Colour
blue
white
grey
Ref.
J
M
N
Colour
yellow
brown
black
Ref.
R
S
V
Colour
red
orange
green
Note: the last letter «G» of the washer’s part number indicates the colour
grey. For other colours, refer to the above table and replace letter «G»
by the one corresponding to the colour required. For the panel cut-out,
please consult chapter «Panel cut-out» on page 158.
E maxi
150
www.lemo.com
®
®
Tooling
DCG Spanners for hexagonal nuts
N
L
øB
Dimensions (mm)
N
Part number
of the nut
(page 134)
DCG.91.149.0TN 14 40 50
GEA.00.240.LN
DCG.91.161.1TN 16 45 52
GEA.0S.240.LN
DCG.91.201.4TN 20 52 65
GEA.1S.240.LN
DCG.91.231.7TN 23 62 68
GEA.2S.240.LN
DCG.91.282.2TN 28 76 73
GEA.3S.240.LN
Part number
B
L
l Material: blackened steel
DCA Spanners for hexagonal nuts with locator for flats on socket thread
N
L max
øB
Dimensions (mm)
N
Part number
of the nut
(page 134)
DCA.91.149.0TN 14 65 50
GEA.00.240.LN
DCA.91.161.1TN 16 73 52
GEA.0S.240.LN
DCA.91.201.4TN 20 85 65
GEA.1S.240.LN
DCA.91.231.7TN 23 100 68
GEA.2S.240.LN
DCA.91.282.2TN 28 120 73
GEA.3S.240.LN
Part number
B
L
l Material: blackened steel
DCB Spanners for round nuts
N
L
øB
Dimensions (mm)
N
Part number
of the nut
(page 135)
DCB.91.119.0TN 11 40 50
GEB.00.240.LN
DCB.91.131.1TN 13 45 50
GEB.0S.240.LN
DCB.91.161.4TN 16 52 65
GEB.1S.240.LN
DCB.91.201.8TN 20 62 65
GEB.2S.240.LN
DCB.91.242.2TN 24 76 70
GEB.3S.240.LN
Part number
B
L
l Material: blackened steel
www.lemo.com
151
®
®
DCH Spanners for conical nuts
øA
øB
L
Part number
N
Dimensions (mm)
A
B
L
N
Part number
of the nut
(page 134)
DCH.91.101.PN
10.1 12.8 124 48.3 GEC.00.240.LC
DCH.91.121.PN
12.1 14.8 124 49.3 GEC.0S.240.LC
DCH.91.161.PN
16.1 21.0 124 51.9 GEC.1S.240.LC
DCH.91.201.PN
20.1 22.8 129 53.5 GEC.2S.240.LC
l Material: dark grey polyurethane
DCH Spanners for notched nuts
øA
Part number
L
øB
N
Dimensions (mm)
A
B
L
N
Part number
of the nut
(page 133)
DCH.91.101.PA
10.1 12.8 124 48.3 GEG.00.240.LC
DCH.91.121.PA
12.1 14.8 124 49.3 GEG.0S.240.LC
DCH.91.181.PA
18.1 22.8 129 53.1 GEG.0E.240.LC
DCH.91.161.PA
16.1 21.0 124 51.2 GEG.1S.240.LC
DCH.91.201.PA
20.1 22.8 129 53.5 GEG.1E.240.LC
DCH.91.141.PA
14.1 18.6 124 51.2 GEG.1S.242.LC
DCH.91.201.PA
20.1 22.8 129 53.5 GEG.2S.240.LC
DCH.91.241.PA
24.1 30.8 134 52.6 GEG.2S.241.LC
DCH.91.251.PA
25.1 32.8 134 55.5 GEG.2E.240.LC
l Material: blue polyurethane
DCP Flat spanners for collet nut
M
N
L
S1
S1
Part number
Dimensions (mm)
L
M
N S1
DCP.99.040.TC
70 0.95 10.5 4.0
DCP.99.045.TC
70 2.00 10.5 4.5
DCP.99.050.TC
78 2.00 12.6 5.0
DCP.99.055.TC
78 2.00 12.6 5.5
DCP.99.060.TC
78 2.00 12.6 6.0
l Material: chrome-plated steel
152
www.lemo.com
®
®
DCP Set of flat spanners for collet nuts
Dimensions (mm)
N
Part number
S1
Series
L
S2
M
DCP.91.001.TN
M N S1 S2
0B-0K 95 2.5 21
8.1 7.1
1B-1K 95 2.5 25 10.1 9.1
DCP.91.023.TN
2B-2K 115 3.0 30 13.1 12.1
L
3B-3K 115 3.0 35 15.1 14.1
DCP.91.045.TN
4B
130 3.0 44 21.1 20.1
5B
130 3.0 54 31.1 30.1
l Material: blackened steel
DCP Set of flat spanners for collet nuts
N
S1
S2
M
Dimensions (mm)
Part number
Series
L
L
DCP.0T.110.TN
DCP.2T.110.TN
M N S1 S2
0T
95 2.5 21 7.55 7.05
1T
95 2.5 25 11.05 9.05
2T
115
3.0
30 14.05 12.05
3T
115
3.0
35 16.05 14.05
l Material: blackened steel
DCP Set of flat spanners for FSl retaining ring & collet nuts
N
M
Dimensions (mm)
L
Part number
Series
L
DCP.91.FSG.TN
00-0B-1B-2B 152
DCP.91.FSG.TN3B
3B
153
M N
2
24
2
32
l Material: blackened steel
DCP Set of flat spanners for FSl retaining ring & collet nuts
M
L
N
Dimensions (mm)
Part number
Series
L
DCP.TT.FSG.TN
TT-0T-1T-2T 152
M N
2
25
l Material: blackened steel
www.lemo.com
153
®
®
DCL Spanners for assembling plugs with 2 latches
N
Dimensions (mm)
Part number
Series
DCL.91.105.0TK
00
10 45 13.5
DCL.91.127.0TK
0S
12 47 17.0
DCL.91.149.0TK
1S
14 52 19.0
B
L
N
L
øB
l Material: blackened steel
DCN Spanners for assembling plugs with 3 latches
øB
N
L
Part number
Series
Dimensions (mm)
B
L
N
DCN.91.905.0TK
00
9 42 12
DCN.91.125.0TK
0S
12 47 17
DCN.91.149.0TK
1S
14 53 19
DCN.91.201.5TK
3S
20 74 22
l Material: blackened steel
154
www.lemo.com
®
Assembly tool for FVB.00.303.NLA plugs
Part number
øA
DCL
L
Series
DCL.91.516.5TK
DPF
Pliers for assembling plugs (series K and E)
øA
220
Pliers DPF
00
A
5
L
165
Dim. (mm)
Series
DPF.91.001.TA
0E-0K
1E-1K
10
DPF.91.023.TA
2E-2K
15
Example for use
Spanner
Dim. (mm)
Part number
øB
DTA
®
3E-3K
A
B
–
12
–
18
–
–
The plug end must be held in the pliers whilst the nut is
tightened with the flat spanner.
Taps
Part number
DTA.99.700.5Z
DTA.99.900.6Z
www.lemo.com
Series
00
0S-0B
Thread
M7 x 0.5
M9 x 0.6
155
®
156
®
www.lemo.com
Panel cut-outs
P2-P5-P10-P11
L mini
P6-P7
P8
B + 0.1
0
B and T series
00-TT
0B-0T
1B-1T
XB
2B-2T
3B-3T
4B
5B
120° x 3
B + 0.1
0
ø A + 0.1
0
0.1
B +0
Series
øC
øA
ø A+ 0.1
0
L mini
H
P1-P3-P4-P9
®
®
ø A1)
7.1
P1
B
L
P2
øA L
6.4 12.5 7.1 11.5
9.1
øA
–
P3
B
–
L
–
øA
–
8.3 14.5 9.1 13.5 14.1 12.6 20.1 10.1
P4
B
øA
P6
B
H
øA
P8
B
C
9.1 15.0 8.30 10.5
–
–
–
–
–
–
–
–
–
–
–
–
P5
ø A2) L
L
–
–
–
12.1 10.6 18.5
–
–
16.1 14.6 22.0 14.1 12.6 21.0 11.17 14.0
15.1 13.6 22.5
–
–
19.2 17.1 28.0 16.1 15.1 23.0 13.95 18.0
14.1 12.6 21.5
18.2 16.6 27.0
25.2 23.6 36.0
35.2 33.6 44.0
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
ø A + 0.1
0
–
–
–
20.2 18.6 29.5
–
–
35.2 33.6 47.1
–
–
25.2 23.6 36.1
–
–
–
–
–
–
–
–
–
–
–
–
3.3 35.2
–
–
–
–
–
–
34
–
–
–
–
–
–
–
–
–
–
–
2.8 35.2
–
øA
7.1
P9
B
–
9.1 8.3
L
12
–
–
19
11.1
17
–
–
–
–
15
–
12.1 10.6
–
15.1 13.6
23
–
25.2 23.6
36
–
47
–
–
18.2 16.6
35.2 33.6
P10
øA
L
–
27
47
–
–
–
–
Note: 1) when using the tapered washer (GBB) a round hole apply 00-TT: ø 7.6 mm / 0B-0T: ø 9.6 mm / 1B-1T: ø 12.6 mm / 2B-2T: ø 15.7 mm /
3B-3T: ø 18.8 mm / 4B: ø 26 mm / 5B: ø 36 mm (tolerance: 0/+0.02). 2) tolerance: 0/+0.02
Cut-out types
Model
ECG
EEG
EGG
EFG
EHG
EJG
Type
Model
P1
EKG
P1
ENY
P1
ENG
P2
ESG
P1
EXG
P5
EYG
Mounting nut torque
Series
00-TT
Type
Model
P1
FAG
P1
HCG
P1
P1/P2
P2/P10
P1/P10
FWG
HEG
HGG
HHG
Type
P1
P9
Model
HMG
HNG
P3
PEG
P9
PKG
P9
P9
PFG
Rll
Type
Model
Sll
P4/P93)
P1
XPF
P2
P1
P1
P4
XBG
XRB
YHG
–
–
–
Type
P9
P9
–
P2
P2
P9
Note: 3) in series 1B use P9.
Torque (Nm)
Metal shell Plastic shell4)
0B-0T
1B-1T
XB
2B-2T
3B-3T
4B
5B
www.lemo.com
1.0
0.4
4.5
0.7
2.5
5.0
0.4
–
6.0
0.8
12.0
5.0
9.0
17.0
1.0
–
Note: 4) these values apply when metal shell are mounted with insulating washer.
157
®
®
S series
Series
00
0S
1S
2S
3S
4S
5S
6S
P1
B
øA
P4
B
9.1 13.5 12.1 10.6 20.0 10.1
9.1
15
15.1 13.6 22.5 15.1 21.5 16.1 14.6 22.0 16.1 15.1
23
ø A1)
7.1
L
6.4 12.5
9.1
8.3 14.5
P2
øA
L
7.1 11.5
øA
–
P3
B
L
–
–
–
–
12.1 10.6 18.5 12.1 19.0 14.1 12.6 21.0 12.1 10.6
18.2 16.6 27.0 18.2 27.0 20.2 18.6 30.0 20.2 18.6
25.2 23.6 36.0 25.2 34.0 25.2 23.6 36.0 25.2 23.6
35.2 33.6 44.0 35.2 44.0 35.2 33.6 47.0 35.2 33.6
48.3 45.6 58.0 48.3 58.0 48.3 45.6 60.0 48.3 45.6
P5
ø A2) L
L
–
–
18
–
–
–
–
–
–
–
øA
P6
B
–
–
–
–
H
øA
P7
B
H
–
–
–
–
–
–
–
–
–
–
–
–
–
P10
øA
L
–
–
–
11.92 15.5 3.3 12.1 12.7 2.7 11.1 12.4 11.1
29
–
36
47
–
60
–
–
–
–
3.3 15.1 15.5
3.3 18.2 18.0
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
4.4 35.2 36.8
–
–
–
P11
øA L
–
–
–
9.1 16
–
–
–
–
–
–
17 12.1 19
–
–
–
–
–
–
–
–
–
–
–
Note: 1) when using the tapered washer (GBB) a round hole apply 00: ø 7.6 mm / 0S: ø 9.6 mm / 1S: ø 12.6 mm / 2S: ø 15.7 mm / 3S: ø 18.8 mm /
4S: ø 26 mm / 5S: ø 36 mm (tolerance: 0/+0.02). 2) tolerance: 0/+0.02
Cut-out types
EBC
EBD
EBS
ECP
EEP
EHP
Type
Model
P6
ERA
P6
ERC
P7
ERD
P1
ERN
P1
ERS
P2/P1
EXP
Mounting nut torque
Series
0S
Type
P1
P1
P1
P1
P2
P2/P10
Model
EWB
Type
P3
PSP
P34)
RAD
FAA
P1/P23)
HGP
P3
HCP
HGW
PSA
Model
P11
P1
PSS
Type
P1
P1
SWH
P1/P25)
P4
Note: 3) in series 6S use P2. 4) use only ø A in 1S series. 5) in series 4S and 5S use P2.
Torque (Nm)
Metal shell Plastic shell6)
2.5
0.4
6.0
0.8
4.5
1S
2S
9.0
3S
12.0
4S
17.0
5S
22.0
6S
0.7
1.0
5.0
–
–
Note: 6) these values apply when metal shell are mounted with insulating washer. 1 N = 0.102 kg
Panel cut-out for mounting with insulating washer
(S-B series)
GRA
Series
0.1
ø A+ 0
00
0S-0B
1S-1B
0.1
B +0
2S-2B
3S-3B
4S-4B
Dim. (mm)
øA
B
8.9
Panel cut-out for mounting with double panel washer
(S-B series)
GRC
øA
8.1
10.9 10.0
13.9 12.3
H
Model
18.0 16.3
21.9 20.3
29.1 27.4
Series
0S-0B
L mini
Note: for nut tightening torques please refer to the corresponding series in the table on page 157.
158
–
1S-1B
Dimensions (mm)
øA
H
L
11
14
14
20
13.5
17.0
www.lemo.com
®
P1
P6-P7
L mini
H
ø A+ 0.1
0
B + 0.1
0
ø A + 0.1
0
0.1
B +0
K series
Series
øA
P1
B
16.1 14.6 22.5
1K
20.2 18.6 29.0
2K
3K
5K
3E
4E
5E
6E
EBR
EEP
EHP
ERA
ERB
ERC
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
4.5
45.1 44.0
Model
P7
ENG
P1
FAG
EVG
FXG
P1
øA
HEG
P1
B
L
14.1 12.6 20.5
16.1 14.6 22.5
3.5
P1
øA
–
–
–
55.3 52.1 68.0
Type
Model
P6
FAA
P1
PSA
P1
P1
P1
P1
www.lemo.com
HGP
PSP
SWH
P73)
PKG
P1
PEG
30.2 28.6 43.0
45.2 42.6 57.0
PBG
P1
P6
–
–
–
–
–
P6
H
–
–
–
–
–
–
–
0K
1K
2K
3K
4K
5K
Torque
(Nm)
5
7
9
12
17
22
1 N = 0.102 kg
P1
P1
15.1 11.8x20.4
–
Series
P1
Sll
B
30.1 29.0
Type
HGG
P1
3.5
Model
P1
2.9
24.2 22.6 35.5
28.6 27.0
Type
20.2 18.6 29.0
Cut-out types E series
Model
–
–
42.6 38.0
P1
2E
H
4.5
EGG
1E
P7
B
45.2 42.6 57.0
EDG
0E
øA
23.1 23.0
P72)
Series
H
3.5
Type
E series
P6
B
22.6 20.6
Model
EHG
øA
3.5
Cut-out types
EEG
Mounting nut torque
24.2 22.6 35.5
30.2 28.6 43.0
4K
EBG
L
14.1 12.6 20.5
0K
®
–
–
Note: 2) for this model dimension B = 18.1. 3) for this model dimension B = 19.1.
Mounting nut torque
Series
0E
1E
2E
3E
4E
5E
6E
Torque
(Nm)
5
7
9
12
17
22
27
1 N = 0.102 kg
Type
P1
P1
P1
P1
P1
159
®
®
PCB drilling pattern
Fixed socket with straight print contact (B-K-T series)
P15
302
øA
A
2
5
1B-1K-1T 0.8
3.00 120°
2B-2K-2T 0.8
4.60 120°
3B-3K-3T 0.8
5.60 120°
Series
Dimensions
A
B
00-TT
0.5
6
72°
0B-0K-0T 0.6
3.0
60°
1B-1K-1T 0.8
3.7
60°
C°
7
2
3
øB
6
5
4
308
8
3
7
C°
3.70
60°
5.80
60°
3B-3K-3T 0.8
7.08
60°
6
Dimensions
A
B
C
2B-2K-2T 0.8
6.4
45°
3B-3K-3T 0.8
7.5
45°
5
4.4
Series
Dimensions
A
B
00-TT
1B-1K-1T 0.8
3.1
45°
øB
2B-2K-2T 0.8
5.0
45°
3B-3K-3T 0.8
6.2
45°
1
5
4
1
5
6
2
4
3
308
1
2
7
8
3
6
4
C
2.8
72°
1B-1K-1T 0.8
3.4
72°
2B-2K-2T 0.8
5.2
72°
3B-3K-3T 0.8
6.7
72°
Dimensions
A
B
C
2B-2K-2T 0.8
5.6
72°
3B-3K-3T 0.8
7.1
72°
Dimensions
A
B
1B-1K-1T
0.8
3.8
C
51°26’
5
309
Series
C°
Dimensions
A
B
0B-0K-0T 0.6
Series
C°
C
3
Series
60°
2B-2K-2T 0.8
2B-2K-2T 0.8
45°
306
1
2
9
3
øA
4
øB
øA
1
3.00
C
1B-1K-1T 0.8
Series
C°
Dimensions
A
B
0B-0K-0T 0.6
øA
C°
Series
2.8
45°
2
C°
307
1
C
2.2
1B-1K-1T 0.8
2.5
øA
4
3
5
øB
øA
1
2
Dimensions
A
B
0B-0K-0T 0.8
Series
2
Series
1.2
1.6
4
3
306
0.6
0.6
1
305
3
C°
2
1.7
C
00-TT
0B-0K-0T 0.6
C°
øA
2.30 120°
øB
4
2
1.35 120°
øB
1
øA
305
0.6
0B-0K-0T 0.8
304
øB
øB
00-TT
C
Dimensions
A
B
øB
øA
3
2
Dimensions
A
B
4
8
7
6
øB
C°
1
Series
øA
303
øA
A
øB
1
Series
Dimensions
A
B
C
0B-0K-0T 0.6
3.2
45°
3B-3K-3T 0.8
7.5
45°
5
Note: contact numbering is for female contact version only.
160
www.lemo.com
®
®
310
Series
2B-2K-2T 0.8 6.30 45° 22°30’ 2.15
3B-3K-3T 0.8 7.90 45° 22°30’ 2.80
5
øA
Series
XB
Dimensions
A B C D
H
312
C°
0.8 5.40 45° 22°30’ 2.40
316
øH
øB
3B-3K-3T 0.8 8.2 90° 3.40
Series
E°
D°
Dimensions
A B D
E
H
4.4 32°44’ 2.00
°
H
318
C°
0.6 10.5 32°44’ 16°22’ 5.00
Series
Dimensions
A B C D E H
E°
D°
2B-2K-2T 0.8 6.7 60° 30° 15° 3.50
3B-3K-3T 0.8 8.4 60° 30° 15° 4.34
øA
øA
4B-4K
Dimensions
A B C D E H
Series
øH
3B-3K-3T 0.8 8.4 32°44’ 16°22’ 3.86
øB
Dimensions
B D
72
2B-2K-2T 0.8 6.6 32°44’ 16°22’ 3.10
øH
A
1B-1K-1T 0.6
2B-2K-2T 0.8 6.5 90° 2.65
øA
316
Series
D°
øA
1B-1K-1T 0.6 4.4 90° 1.90
øH
36°
Dimensions
A B C H
H
øB
øB
øH
°
36
°
Dimensions
A B C D
3B-3K-3T 0.8 8.20 45° 22°30’ 3.40
øA
øA
Series
72
Series
2B-2K-2T 0.8 6.50 45° 22°30’ 2.80
D°
øH
D°
314
C°
0.5 3.3 40° 20° 1.25
120°
312
C°
0B-0T
øB
6
D°
Dimensions
A B C D H
øA
4
9
C°
1B-1K-1T 0.6 3.95 45° 22°30’ 1.40
Series
øB
10
312
øB
3
7
H
øH
2
8
øB
1
H
C°
D°
Dimensions
A B C D
319
E°
D°
2B-2K-2T 0.8 6.7 60° 30° 15° 3.5
øB
øA
Series
°2
H
øB
4B-4K
0.6 11.00 51°26’ 27°42’ 6.00
E°
XB
Dimensions
A B D
E
H
322
C°
Series
Dimensions
A B C D
E H
0.6 5.7 25°42’ 12°51’ 3.1
3B-3K-3T 0.6 8.8 45° 25°43’ 22°30’ 5
E°
øA
2B-2K-2T.326
ø 0.6
40°
ø9
øE
ø 5.6
0°
ø7
øA
40°
12
0°
0.6 11.1 45° 25°43’ 2.2 6.65
25°43'
25°43'
12
4B-4K
øB
øH
D°
3B-3K-3T 0.6 8.8 45° 25°43’ 1.8 5.30
3B-3K-3T.326
ø 4.2
Dimensions
A B C D E H
ø 1.6
Series
C°
ø 2.1
øA
324
øB
øH
D°
øB
øH
D°
51
Dimensions
B
C
D
C°
322
5’
A
3B-3K-3T 0.6 8.62 51°26’ 27°42’ 4.78
øA
øH
D°
Series
øH
C°
320
ø 0.6
Note: contact numbering is for female contact version only.
www.lemo.com
161
®
3B-3K.332
32°44’
ø 5.7
ø7
4.6
2.6
21°11’
5B-5K.350
5B-5K.354
0'
ø 0.6
15'
5°
22°30'
1
ø 3.8
ø 19.2
ø 13.73
ø 3.1
'
40°
ø 8.36
12
0°
ø 12
ø 8.65
ø 5.3
ø2
0°
12
ø 0.6
15°40
17°8'34''
11°
ø9
ø 7.94
2
7°3
24°
40°
36°
ø 0.6
ø 4.24
18°
ø 11.64
2'
27°4
4°
ø 19.4
4B-4K.348
'
°26
51
ø 7.2
21°11'
ø 14.2
4B-4K.340
ø 0.6
ø 0.6
ø9
ø 0.6
2.6
2.2
36°
ø9
°
72
ø 11.4
11°15'
22°
30
'
ø 5.7
2.2
22°
30
'
11°15'
36°
7.4
°
90
ø 7.0
36°
°
90
2B-2K-2T.332
ø 0.6
4B-4K.330
ø 3.1
3B-3K-3T.330
ø 2.2
®
ø 0.6
5B-5K.364
18
°5
7
°
ø 19.84
ø 14.96
ø 5.05
60
'
ø 10.08
13°5
1'
ø 0.6
27°41'32''
Note: all views are from the side of the socket.
162
www.lemo.com
®
®
00
TT
øC
0.5
302/303/304
0B
0K
0T
302/303
312
1B
1K
1T
302/303/304/305/306/307/308
XB
312
302/303/304/305/306/307
308/310/312/314/316/318/319
303/304/305/306/307/308/309
310/312/314/316/318
316/320/324/330/340/348
5B
5K
3.0
0.7
3.0
0.7
3.0
350/354/364
4.0
3.0
0B
302/303
306/307/309
1B
302/303/304/305/306/307/308
302/303/304/305/306/307/308
310/312/314/316/318/319
Ell
3.0
0.5
5.0
0.5
5.0
0.7
4.5
0.5
3.0
–
–
4.5
0.7
3.0
0.7
3.8
–
–
0.7
5.5
–
–
0.5
310/314/316
2B
Models
EZG/EYG
XPF
øC
L
øC
L
0.5
304/305
–
3.8
–
–
–
EZG/EYG/XPF
3.0
0.7
0.7
348
3.2
0.7
0.5
320/322/324/326/330/332
4B
4K
3.0
0.5
326/332
3B
3K
3T
0.4
0.5
322
2B
2K
2T
3.2
0.5
310/314/316
3.0
0.7
0.5
304/305/306/307/309
L
Type
øC
Dimensions
Type
Length of straight print contacts
(for socket EZG/EYG/XPF)
øC
Length of straight print contacts
(for socket Ell)
L
L
5.0
5.0
Note: This table does not apply for socket Hll; socket EHl and plugs FAl/FWl.
Fixed socket for printed circuit (B series)
Holes for fixing the housing
EYG-EZG
B
øA
Series
00
0B
1B
2B
P16
Dimensions
A
B
0.81)
5.08
1.72)
7.62
1.72)
1.72)
7.62
XPF.0B
B
Series
øA
0B
Dimensions
A
B
1.7
5.08
10.16
Note: Mounting torque for screws: 0.1 Nm. 1) to solder. 2) to screw.
www.lemo.com
163
®
®
Fixed socket with elbow print contact (B-K-T series)
P17
302
øA
1
A
A
Series
Dim.
A
00-TT
0.6
0B-0K-0T 0.7
2
1B-1K-1T 0.9
2.54
2B-2K-2T 0.9
303
Dimensions
A L
00-TT
0.6 1.27
304
øA
Series
Dimensions
A L
00-TT
0.6 2.54
L
øA
Series
0B-0K-0T 0.7 1.27
3
4
3
0B-0K-0T 0.7 2.54
1
2
1B-1K-1T 0.7 2.54
L
1
1B-1K-1T 0.9 1.27
L
2
2B-2K-2T 0.9 2.54
2.54
2B-2K-2T 0.9 3.50
2.54
3B-3K-3T 0.9 2.54
3
4
1.27
2.54
2
2.54 2.54
1B-1K-1T / 2B-2K-2T /
3B-3K-3T.314
14
6
13
12
2
2
3
4
11
15
13
14
10
2
3
5
1
2.54 2.54 2.54 2.54
4
3
2.54 2.54
2.54 2.54
7
6
8
12
11
5
1
9
10
4
2
3
2.54 2.54 2.54
3B-3K-3T.318
9
11
12
18
17
14
15
3
4
7
16
2
10
9
18
17
13
16
14
15
3
4
11
8
13
1
4
2
4
2.54 2.54 2.54
10
5
8
2B-2K-2T / 3B-3K-3T.312
2B-2K-2T.318
6
3
1.27
2.54 2.54 2.54 2.54
16
2
4
9
8
7
12
1
5
6
8
10
3
1.27
5
9
7
11
1
6
9
2B-2K-2T / 3B-3K-3T.316
ø 0.7
10
7
1
2.54 2.54
8
9
8
7
6
1
5
2.54 2.54
ø 0.6
1.27
5
3
2
1B-1K-1T / 2B-2K-2T /
3B-3K-3T.310
1.27
1
0B-0K-0T.309
ø 0.7
6
2.54 2.54
ø 0.7
ø 0.9
(3B-3K)
7
1
7
12
6
7
6
1
5
1.27
8
2
2.54
ø 0.7
2B-2K-2T / 3B-3K-3T.308
4
7
0.92
1.27
1.27
2.54 2.54
3
2
5
6
1.27
1
2
8
1B-1K-1T.308
2.54 2.54 2.54
4
7
3
2
2.54 2.54
2B-2K-2T.307
ø 0.7
1
6
ø 0.9
3
4
ø 0.7
0B-0K-0T / 1B-1K-1T.307
5
6
1
2.54 2.54
2.54 2.54
4
5
3
1.27
2B-2K-2T / 3B-3K-3T.306
2
ø 0.9
1.27
1.27
2.54 2.54
5
6
ø 0.7
3
2
1
ø 0.7
ø 0.9
(3B-3K)
3
ø 0.7
4
1.27
4
1
5
ø 0.7
2
ø 0.7
ø 0.9
(3B-3K)
4
ø 0.7
5
1
5
0B-0K-0T / 1B-1K-1T.306
2B-2K-2T.305
ø 0.9
1B-1K-1T / 3B-3K-3T.305
2.54 2.54
0B-0K-0T.305
5
5.08
2.54
Note: contact numbering is for female contact version only.
164
www.lemo.com
®
®
Fixed socket with elbow print contact (B-K-T series)
2B-2K-2T.319
P17
3B-3K-3T.320
3B-3K-3T.324
2B-2K-2T.326
ø 0.6
11
7
16
15
3
4
2
5
7
16
17
3
1.27
1.27
18
15
2.54 2.54 2.54 2.54
23
15
19
8
20
1.27
4
5
6
5
2.54 2.54 2.54 2.54 2.54
3B-3K.332
ø 0.7
13
13
12
16
15
25
24
11
32
31
23
15
17
27
1
18
2
3
30
22
20
21
7
28
6
25
32
18
31
30
19
20
3
4
2
10
24
29
1
8
5
11
27
17
9
23
22
21
4
2.54 2.54 2.54 2.54 2.54 2.54
12
26
9
29
14
16
10
19
21
7
3
17
4
28
22
2
4
1.27
9
29
7
18
3
26
23
28
18
6
5
2.54 2.54 2.54 2.54 2.54
27
1
18
17
24
8
19
25
2
14
11
30
17
7
3
25
16
19
16
2
12
26
ø 0.6
10
26
8
25
13
15
20
24
1
14
9
26
15
16
2.54 2.54 2.54 2.54
ø 0.7
10
22
14
23
1
6
5
9
20
24
2B-2K-2T.332
11
21
14
4
3B-3K-3T.330
12
18
17
3
5
ø 0.7
13
7
16
2
21
22
19
24
10
13
8
15
1.27
3B-3K-3T.326
4
23
1
6
12
9
20
14
8
1
1.27
2
14
6
10
21
22
1.27
19
14
12
13
9
8
7
6
5
6
2.54 2.54 2.54 2.54 2.54 2.54
1.27
8
13
1
19
11
ø 0.7
17
20
12
13
1.27
18
11
12
10
ø 0.7
9
ø 0.7
10
11
2.54 2.54 2.54 2.54 2.54 2.54
Note: contact numbering is for female contact version only.
P20
P18 - EPG.00.302 - XBG.00.302
XRB.00.3021)
5.08
P18 - EPG.00.3032) - XBG.00.3032)
XRB.00.3031)
=
A
=
=
=
ø 0.6
A
1.9
ø 0.8
2.54
1.27
2.54
1.27
ø 0.8
7.62
ø 1.7
7.62
1.27
1.9
1.9
5.08
5.08
ø 0.6
7.62
1.27
P19 - EPG-EXG (0B/1B.302)
Screw mount
2.54
5.08
ø 0.6
2.54
ø 0.8
P19 - EPG-EXG (0B/1B.302)
Solder mount
1.27
5.08
P18 - EPG.00.305
1.9
ø 0.6
1.27
P18 - EPG.00.304 - XBG.00.304
XRB.00.3041)
ø 0.8
5.08
ø 0.8
ø 0.8
2.54
1.27
P19
0.63
P18
7.62
Elbow socket (90°) for printed circuit (B series)
ø 0.8
2.54
Note: 1) for the XRB.00 series the holes for shell fixing are different (see p. 35).
2) the dimensions for the EPG.00.303.HLN and XBG.00.303.HLN models are given on page 26. For other models please contact factory.
www.lemo.com
165
®
7.62
7.62
2.54
7.62
1.27
2.54
7.62
7.62
1.27
2.54
7.62
7.62
ø 0.8
1.27
ø 1.7
12.7
12.7
12.7
ø 0.7
1.27
Series
Dimensions
A
B
0S-0E 0.8
2.2
1S-1E 0.8
3.0
2S-2E 0.8
4.5
P21
303
C°
øB
øA
Fixed socket with straight print contact (S-E series)
øB
1.27
ø 0.8
1.27
2.54
1.27
166
1.27
7.62
1.27
ø 0.8
2.54
øA
ø 1.7
7.62
P20 - EPG.1B.314
Screw mount
ø 0.7
302
P19 - EPG-EXG (1B.310)
Screw mount
ø 0.8
7.62
ø 0.8
1.27
P20 - EPG.1B.314
Solder mount
1.27
2.54
7.62
1.27
2.54
ø 0.8
1.27
ø 0.8
1.27
P19 - EPG-EXG (1B.310)
Solder mount
ø 1.7
7.62
7.62
1.27
2.54
P19 - EPG-EXG (0B.309)
Screw mount
ø 0.8
ø 1.7
7.62
ø 0.8
1.27
2.54
7.62
P19 - EPG-EXG (1B.308)
Screw mount
ø 0.8
7.62
ø 0.8
1.27
2.54
12.7
7.62
2.54
7.62
1.27
2.54
7.62
1.27
2.54
ø 0.8
1.27
P19 - EPG-EXG (0B.309)
Solder mount
ø 0.8
2.54
P19 - EPG-EXG (1B.308)
Solder mount
ø 1.7
7.62
ø 1.7
7.62
ø 0.8
2.54
P19 - EPG-EXG (0B/1B.307)
Screw mount
ø 0.8
P19 - EPG-EXG (0B/1B.306)
Screw mount
ø 0.8
7.62
ø 0.8
2.54
P19 - EPG-EXG (0B/1B.307)
Solder mount
ø 0.8
2.54
P19 - EPG-EXG (0B/1B.306)
Solder mount
ø 1.7
7.62
ø 0.8
2.54
7.62
2.54
P19 - EPG-EXG (0B/1B.305)
Screw mount
2.54
ø 0.8
ø 1.7
7.62
ø 0.8
2.54
7.62
2.54
P19 - EPG-EXG (0B/1B.305)
Solder mount
P19 - EPG-EXG (0B/1B.304)
Screw mount
ø 0.8
7.62
ø 0.8
2.54
ø 0.8
2.54
7.62
P19 - EPG-EXG (0B/1B.304)
Solder mount
ø 1.7
7.62
P20
7.62
2.54
ø 0.8
7.62
P19
P19 - EPG-EXG (0B/1B.303)
Screw mount
7.62
2.54
P19 - EPG-EXG (0B/1B.303)
Solder mount
P18
2.54
Elbow socket (90°) for printed circuit (B series)
2.54
®
Series
Dimensions
A
B
C
0S-0E 0.6
2.8
45°
1S-1E 0.8
3.5
45°
2S-2E 0.8
5.5
60°
www.lemo.com
®
®
Fixed socket with straight print contact (S-E series)
3.5
45°
2S-2E 0.8
5.0
45°
Series
øB
øA
1S-1E 0.8
3.5
60°
2S-2E 0.8
5.5
60°
3S-3E 0.8
6.5
60°
Series
øB
A
Dimensions
B C
2S-2E 0.8
6.5
45° 22°30’
3S-3E 0.8
7.8
45° 22°30’
60°
310
D
Series
Dimensions
D E
F
2S-2E 45° 22°30’ 2.75
3.25
3S-3E 45° 22°30’ 3.25
3.90
Series
D°
C°
C
Dimensions
A B C D
E
2S-2E 0.8 6.5 45° 22°30’ 1.25
3S-3E 0.8 7.8 45° 22°30’ 1.50
øA
3S-3E.313
3S-3E.314
ø 0.8
1.3
1.3
3.2
3.2
3S-3E.316
6 x 1.2
6 x 1.2
8x1
2.9
6 x 1.2
1.2
3S-3E.312
ø 0.8
D
D°
C°
ø 0.8
øA
C°
D°
307
3.2
308
C
Dimensions
B C
2S-2E 0.8 5.5 60° 60°
D°
1.3
C°
Dimensions
A
B
øB
1S-1E 0.8
A
1S-1E 0.8 3.5 60° 45°
F
45°
Series
E
2.8
C°
øA
0S-0E 0.6
305
øB
306
C
ø 0.8
øB
Dimensions
A
B
E
Series
øA
C°
ø 0.8
304
P21
3S-3E.318
ø 0.8
1.2
2.9
8x1
Note: all views are from the side of the socket.
øC
Length of straight print contacts (for socket Ell)
L
Type
Dimensions
øC
L
0S
0E
302
0.7
3.0
303/304
0.5
3.0
1S
1E
302
0.7/1.5 3.0/5.0
303/304/305
0.7
3.0
305/306
0.5
3.0
Type
Dimensions
øC
L
2S
2E
303/304/305/306/307/308/310
0.7
3.0
3S
3E
305/306/307/308/310
312/313/314/316/318
0.7
3.0
Note: This table does not apply for HGP and EHP sockets and for FAA plugs.
www.lemo.com
167
®
Elbow socket (90°) for printed circuit (S series)
P22 - EPL - EXP
Solder mount
P22 - EPL - EXP
Screw mount
P23
P23 - EPL.00.113
P23 - EPL.0S.116
5.08
5.08
ø 1.7
7.62
ø 0.8
2.54
2.54
ø 1.1
=
=
7.62
2.54
7.62
2.54
2.54
2.54
2.54
=
2.54
ø 0.8
7.62
2.54
P22
=
®
2.54
2.54
2.54
Note: all dimensions are in millimetres.
Fixed socket with elbow print contact (S-E series)
P24
302
øA
1
A
Dim.
A
Series
0.7
0S-0E
0.9
1S-1E
2
A
2.54
Series
øA
A
0.7
C
0S-0E
B
1S-1E
2
2.00
0.7
1
3
Dimensions
B
C
1.00
2.48
304
0S-0E
1.24
4
2
3
3
2S-2E
0.9
2S-2E
4
2.54 2.54
6
2
5
3
4
2.0
0.9
3.5
3.5
Dim.
A
Series
0.7
1S-1E
øA
0.7
1S-1E
1
0.7
0.7
1S-1E
306
2.4 2.4
2
Dim.
A
Series
5
øA
1
2.54 2.54
1
2.54
2.54
305
Dimensions
A
B
Series
øA
B
303
0.9
2S-2E
2.54
2S-2E.307
2S-2E / 3S-3E.310
3S-3E.312
1.2
2S-2E.308
5
2.54 2.54
4
5
2.54 2.54 2.54
6
2.54 2.54 2.54
7
4
8
5
9
6
10
11
ø 0.7
10
3
1
2.4
9
3
5
1.25
4
1.75
4
1.75
3
6
7
2
12
1.2
3
8
2
ø 0.7
1
7
6
6
1.27
8
ø 0.7
6
2
1
2
2.5
7
ø 0.7
1
2.54 2.54 2.54
3S-3E.316
1.2
3S-3E.314
8
6
10
7
11
2
13
10
13
14
3
14
15
7
11
8
12
4
16
1.2
2.54 2.54 2.54
6
2
1.2
3
9
2.4
9
ø 0.7
5
5
1
12
ø 0.7
4
1
2.54 2.54 2.54
168
www.lemo.com
®
®
Cable assembly (B, K, T, S and E series)
Cable stripping lengths (B series)
M3
straight plugs and sockets with cable collet, clamping type D or M (solder or crimp contacts)
elbow plugs (90°) with cable collet, clamping type D or M (solder or crimp contacts)
Type
00
ø contact A
(mm)
M1
302/303/304
305/306
0B1)
302/303
304/305
306/307/3092)
312
1B1)
302/303
304/305
306/307/308
310/314/316
XB
312
322
2B
302
303
304/305/306/307
308/310
312/314/316/318/319
326/332
3B
302
303/304
305/306/307
308/310
309
312/314/316/318
320/322/324/326/330/332
L
Solder
S
7.0
4
0.5
7.0
0.9
0.5
0.35
0.7
T
M1
Cable stripping lengths (mm)
L
Crimp
S
–
–
4
2.5
10.0
14.5
7
3.5
14.0
7
2.5
14.5
0.35 14.0
7
7
2.5
3.5
2.5
T
L
Solder
S
9.5
4
4
3.0
9.5
17.0
7
4.0
18.0
7
3.0
17.0
–
7
–
–
4.0
–
T
M3
L
Crimp
S
–
–
22.0
7
4
2.5
12.5
19.5
7
3.5
22.0
19.0
7
2.5
23.0
19.5
19.0
7
7
2.5
3.5
2.5
18.0
8
4.0
25.5
8
3.5
28.0
0.7
14.5
8
3.0
18.0
8
4.0
25.5
8
3.0
28.0
0.5
16.5
8
3.0
2.5
18.0
–
8
–
4.0
–
0.7
16.5
7.5
3.5
–
–
–
2.0
19.0
9
4.0
22.0
9
1.3
18.0
9
3.5
20.0
9
0.5
1.6
0.9
0.7
0.5
17.5
19.0
17.0
17.0
17.0
8
9
9
9
9
4.0
3.5
3.0
3.0
2.5
–
22.0
20.0
20.0
–
–
9
9
9
–
25.5
27.5
8
8
–
–
5.5
30.0
4.0
29.0
–
5.5
4.0
4.0
–
–
30.0
28.0
28.0
28.0
3.0
2.5
7
3.0
8
3.5
8
4.0
28.0
8
14.5
7
–
14.5
0.9
3.0
–
1.3
–
T
4
–
4.0
–
8
4.0
8
4.0
–
4.0
–
–
–
–
–
9
4.0
33.0
9
5.5
9
3.5
31.0
9
4.0
–
9
9
9
9
–
3.5
3.0
3.0
2.5
–
33.0
31.0
31.0
–
–
9
9
9
–
–
5.5
4.0
–
24.0
10
4.5
28.0
10
5.5
35.0
10
4.5
39.0
10
5.5
1.6
23.0
10
3.5
27.0
10
5.5
34.0
10
3.5
38.0
10
5.5
1.3
1.3
2.0
0.9
0.7
23.0
22.0
22.0
21.0
21.0
10
10
10
10
10
4.0
3.5
3.5
4.0
3.0
3.0
27.0
25.0
25.0
25.0
25.0
10
10
10
10
10
5.5
4.0
4.0
5.5
4.0
4.0
34.0
33.0
33.0
32.0
32.0
10
10
10
10
10
4.0
3.5
3.5
4.0
3.0
3.0
38.0
36.0
36.0
36.0
36.0
10
10
10
10
10
S
4.0
3.0
2.0
L
T
5.5
4.0
4.0
5.5
4.0
4.0
Note: 1) In 0B and 1B series, «L» and «S» dimensions shall be increased by 2 mm for the largest collet (D56 in 0B series; D76 in 1B series).
The tolerances on these dimensions are: L: ± 0.5 mm; S: ± 0.5 mm; T: ± 0.2 mm.
www.lemo.com
169
®
®
Cable stripping lengths (B series)
M1
straight plugs and sockets with cable collet, clamping type D or M (solder or crimp contacts)
M3
elbow plugs (90°) with cable collet, clamping type D or M (solder or crimp contacts)
ø contact A
(mm)
L
304
3.0
33.0
12
4.5
36.0
12
5.5
41.0
12
4.5
45.0
12
5.5
306/307
2.0
32.0
12
4.0
36.0
12
5.5
41.0
12
4.0
45.0
12
5.5
310
1.6
32.0
12
3.5
36.0
12
5.5
39.0
12
3.5
43.0
12
5.5
312
1.3
32.0
12
3.5
36.0
12
4.0
39.0
12
3.5
43.0
12
4.0
Type
4B
5B1)
Cable stripping lengths (mm)
M1
Solder
S
T
M3
L
Crimp
S
T
L
Solder
S
T
L
Crimp
S
T
L
T
316/320/324/330
0.9
32.0
12
3.0
34.0
12
4.0
39.0
12
3.0
43.0
12
4.0
340/348
0.7
32.0
12
3.0
34.0
12
4.0
39.0
12
3.0
43.0
12
4.0
302
6.0
42.0
18
7.5
–
–
–
70.0
18
7.5
–
–
–
304
4.0
47.0
18
5.5
50.0
18
7.0
75.0
18
5.5
78.0
18
7.0
310
3.0
47.0
18
4.5
50.0
18
7.0
75.0
18
4.5
78.0
18
7.0
314/316
2.0
46.0
18
4.0
49.0
18
5.5
74.0
18
4.0
77.0
18
5.5
320
1.6
46.0
18
3.5
49.0
18
5.5
74.0
18
3.5
77.0
18
5.5
330/340/348
1.3
45.0
18
3.5
48.0
18
4.0
74.0
18
3.5
77.0
18
4.0
350/354/364
0.9
45.0
18
3.0
48.0
18
4.0
74.0
18
3.0
77.0
18
4.0
S
Note: 1) In 5B series, «L» and «S» dimensions shall be increased by 13 mm for the largest collet (D25).
elbow plugs (90°) with cable collet, clamping type D or M (solder or crimp contacts) (FSG model)
00
0B
Type
ø contact A
(mm)
M5
302/303/304
0.5
12.0
4
2.5
15.0
5
3.0
305/306
0.35 12.0
4
2.5
–
–
–
302/303
0.9
21.5
7
3.5
24.0
7
4.0
304/305
0.7
21.5
7
3.5
24.0
7
4.0
306/307/3091)
0.5
21.0
7
3.5
24.0
7
3.0
0.35 21.0
7
3.5
–
–
–
302/303
1.3
27.0
8
3.5
32.0
8
4.0
304/305
0.9
27.0
8
3.5
32.0
8
4.0
306/3072)/308
0.7
27.0
8
3.5
32.0
8
4.0
310/314/3163)
0.5
29.0
8
3.5
–
–
–
302
2.0
35.0
9
4.0
38.0
9
5.5
303
1.6
35.0
9
4.0
38.0
9
5.5
304/305/306/307
1.3
34.0
9
4.0
36.0
9
4.0
308/310
0.9
33.0
9
4.0
36.0
9
4.0
312/314/316/318/319
0.7
33.0
9
3.5
36.0
9
4.0
326/332
0.5
33.0
9
3.5
–
–
–
312
1B
2B
Cable stripping lengths (mm)
M5
Solder
Crimp
T
L
S
T
L
S
L
T
S
Note: 1) center wire L = 16.5. 2) center wire L = 20.5. 3) 5 center wires L = 20.5.
The tolerances on these dimensions are: L: ± 0.5 mm; S: ± 0.5 mm; T: ± 0.2 mm.
170
www.lemo.com
®
®
Cable stripping lengths (B series)
straight plug, short version, clamping type D or M (solder or crimp contacts)
ø contact A
(mm)
M4
Cable stripping lengths (mm)
M4
Solder
Crimp
T
L
S
T
L
S
302/303
0.9
9.5
8
3.0
13.0
8
4.0
304/305
0.7
9.5
8
3.0
13.0
8
4.0
306/307/3092)
0.5
10.0
8
2.5
13.5
8
3.0
Type
0B
T
S
straight plug, long version, clamping type D or M (solder or crimp contacts)
Cable stripping lengths (mm)
M2
Solder
Crimp
L
S
T
L
S
T
Type
ø contact A
(mm)
M2
L
302/303
1.3
39.5
8
3.5
43.0
8
4.0
304/305
0.9
39.5
8
3.0
43.0
8
4.0
306/307/308
0.7
39.5
8
3.0
43.0
8
4.0
310/314/316
0.5
42.0
8
2.5
–
–
–
302
2.0
49.0
9
4.0
53.0
9
5.5
303
1.6
49.0
9
3.5
53.0
9
5.5
304/305/306/307
1.3
48.0
9
3.5
50.0
9
4.0
308/310
0.9
47.0
9
3.0
49.0
9
4.0
312/314/316/318/319
0.7
47.0
9
3.0
49.0
9
4.0
326/332
0.5
47.0
9
2.5
–
–
–
1B1)
2B
L
T
S
Note: 1) In 1B series, «L» and «S» dimensions shall be increased by 2 mm for the largest collet (D76 in 1B series).
2) Crimp contacts are available only for connectors fitted with male contacts.
The tolerances on these dimensions are: L: ± 0.5 mm; S: ± 0.5 mm; T: ± 0.2 mm.
www.lemo.com
171
®
®
Cable stripping lengths (K series)
M1
straight plugs and sockets with cable collet, clamping type C (solder or crimp contacts)
M3
elbow plug (90°) with cable collet, clamping type C (solder or crimp contacts)
0K
2K
0.9 9.5 6 3.5
12.0 6 4.0
22.5 6 3.5
25.0 6 4.0
304/305
0.7 9.5 6 3.5
12.0 6 4.0
22.5 6 3.5
25.0 6 4.0
306/307/3091)
13.0 6 4.0
22.0 6 2.5
26.0 6 4.0
0.5 9.0 6 2.5
4K
5K
0.35
9.0
6
2.5
–
–
– 22.0 6 2.5 –
–
–
302/303
1.3
11.0 7 3.5
14.5 7 4.0
27.5 7 3.5
31.0 7 4.0
304/305
0.9
11.0 7 3.0
14.5 7 4.0
27.5 7 3.0
31.0 7 4.0
306/307/308
11.0 7 3.0
14.5 7 4.0
27.5 7 3.0
31.0 7 4.0
0.7
310/314/316
0.5
13.0 7
2.5 14.0
7
3.0 29.5 7 2.5 –
–
–
302
2.0
16.5 8 4.0
19.5 8 5.5
36.0 8 4.0
39.0 8 5.5
303
1.6
16.5 8 3.5
19.5 8 5.5
36.0 8 3.5
39.0 8 5.5
304/305/306/307
15.5 8 3.5
17.5 8 4.0
35.0 8 3.5
37.0 8 4.0
1.3
308/310
14.5 8 3.0
17.5 8 4.0
34.0 8 3.0
37.0 8 4.0
0.9
312/314/316/318/319
14.5 8 3.0
17.5 8 4.0
34.0 8 3.0
37.0 8 4.0
0.7
326/332
3K
T
302/303
312
1K
ø contact A
(mm)
Type
Cable stripping lengths (mm)
M1
M3
Solder Crimp Solder Crimp
L S
T L S
T L S
T L S
0.5
14.5 8
2.5
–
–
– 34.0 8 2.5 –
–
–
302
3.0 19.0 10 4.5 23.0 10 5.5 48.0 10 4.5 53.0 10 5.5
303/304
2.0 18.0 10 4.0 22.0 10 5.5 48.0 10 4.0 52.0 10 5.5
305/306/307
1.6 18.0 10 3.5 22.0 10 5.5 48.0 10 3.5 52.0 10 5.5
308/310
1.3 17.0 10 3.5 20.0 10 4.0 47.0 10 3.5 50.0 10 4.0
309
1.3 3.5 4.0 3.5 4.0
17.0
10 20.0
10 47.0
10 50.0
10
2.0 4.0 5.5 4.0
5.5
312/314/316/318
0.9 16.0 10 3.0 20.0 10 4.0 46.0 10 3.0 50.0 10 4.0
320/322/324/326/330
0.7 16.0 10 3.0 20.0 10 4.0 46.0 10 3.0 50.0 10 4.0
304
3.0 22.0 11 4.5 25.0 11 5.5 52.0 11 4.5 55.0 11 5.5
306/307
2.0 21.0 11 4.0 25.0 11 5.5 51.0 11 4.0 55.0 11 5.5
310
1.6 21.0 11 3.5 25.0 11 5.5 51.0 11 3.5 55.0 11 5.5
312
1.3 21.0 11 3.5 25.0 11 4.0 51.0 11 3.5 55.0 11 4.0
316/320/324/330
0.9 21.0 11 3.0 23.0 11 4.0 51.0 11 3.0 53.0 11 4.0
340/348
0.7 21.0 11 3.0 23.0 11 4.0 51.0 11 3.0 53.0 11 4.0
302
6.0 24.0 14 7.5
–
–
–
–
–
–
–
–
–
304
4.0 29.0 14 5.5 32.0 14 7.0 –
–
–
–
–
–
310
3.0 29.0 14 4.5 32.0 14 7.0 –
–
–
–
–
–
314/316
2.0 28.0 14 4.0 31.0 14 5.5 –
–
–
–
–
–
320
1.6 28.0 14 3.5 31.0 14 5.5 –
–
–
–
–
–
330/340/348
1.3 27.0 14 3.5 30.0 14 4.0 –
–
–
–
–
–
350/354/364
0.9 27.0 14 3.0 30.0 14 4.0 –
–
–
–
–
–
L
T
S
Note: 1) crimp contacts are available only for connectors fitted with male contacts. The tolerances on these dim. are: L: ± 0.5 mm; S: ± 0.5 mm; T: ± 0.2 mm.
172
www.lemo.com
®
®
Cable stripping lengths (K series)
straight plug and socket with oversize cable collet, clamping type K (solder or crimp contacts)
Type
1K
302/303
304/305
306/307/308
310/314/316
2K
302
303
304/305/306/307
308/310
312/314/316/318/319
326/332
3K
302
303/304
305/306/307
308/310
309
312/314/316/318
4K
320/322/324/326/330
304
306/307
310
312
316/320/324/330
340/348
ø contact A
(mm)
M2
Cable stripping lengths (mm)
M2
Solder
Crimp
L
S
T
L
S
T
1.3
23.5
8
3.5
27.5
8
4.0
0.7
23.5
8
3.0
27.5
8
4.0
0.9
0.5
23.5
24.5
8
8
3.0
2.5
27.5
–
8
–
–
2.0
29.5
10
4.0
32.5
10
5.5
1.3
28.5
10
3.5
30.5
10
4.0
1.6
0.9
0.7
0.5
29.5
27.5
27.5
27.5
10
10
10
10
3.5
3.0
3.0
2.5
32.5
30.5
30.5
–
10
10
10
–
5.5
4.0
4.0
–
3.0
37.0
11
4.5
41.0
11
5.5
1.6
36.0
11
3.5
40.0
11
5.5
2.0
1.3
1.3
2.0
0.9
0.7
36.0
35.0
35.0
34.0
34.0
11
11
11
11
11
4.0
3.5
3.5
4.0
3.0
3.0
40.0
38.0
38.0
38.0
38.0
11
11
11
11
11
5.5
4.0
4.0
14
4.5
48.0
14
5.5
1.6
44.0
14
3.5
48.0
14
5.5
1.3
0.9
0.7
44.0
44.0
44.0
44.0
14
14
14
14
4.0
3.5
3.0
3.0
48.0
48.0
46.0
46.0
14
14
14
14
S
4.0
5.5
45.0
2.0
L
T
4.0
3.0
Note: the tolerances on these dim. are: L: ± 0.5 mm; S: ± 0.5 mm; T: ± 0.2 mm.
www.lemo.com
4.0
5.5
4.0
4.0
4.0
173
®
®
Cable stripping lengths (T series)
M1
straight plugs and sockets with cable collet, clamping type C (solder or crimp contacts)
M2
straight plugs and sockets with cable collet, clamping type K (solder or crimp contacts)
T
0.5 10.0 4.5 2.5 13.5 4.5 3.0 –
–
–
–
–
–
305
0.35 10.0 4.5
306
0.35 11.0 4.5 2.5
Type
TT
0T
302/303/304
2T
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
0.9 11.5 6.0 3.0 13.5 6.0 4.0 22.0 7.0 3.0 24.0 7.0 4.0
304/305
0.7 11.5 6.0 3.0 13.5 6.0 4.0 22.0 7.0 3.0 24.0 7.0 4.0
306/307/3091)
0.5 10.5 6.0 2.5 14.0 6.0 3.0 21.0 7.0 2.5 24.5 7.0 3.0
0.35 10.5 6.0
2.5
–
–
– 21.0 7.0 2.5 –
–
–
302/303
1.3 12.0 8.0 3.5 14.0 8.0 4.0 26.0 8.5 3.5 28.0 8.5 4.0
304/305
0.9 11.5 8.0 3.0 14.0 8.0 4.0 26.0 8.5 3.0 28.5 8.5 4.0
306/307/308
0.7 11.5 8.0 3.0 14.0 8.0 4.0 26.0 8.5 3.0 28.5 8.5 4.0
310/314/316
0.5 11.5 8.0 2.5 15.0 8.0
3.0 25.5 8.5 2.5 29.0 8.5
2.0 16.0 9.5 4.0 19.0 9.5 5.5 30.0 9.0 4.0 33.0 9.0 5.5
303
1.6 16.0 9.5 3.5 19.0 9.5 5.5 30.0 9.0 3.5 33.0 9.0 5.5
304/305/306/307
1.3 16.0 9.5 3.5 19.0 9.5 4.0 30.0 9.0 3.5 33.0 9.0 4.0
308/310
0.9 16.0 9.5 3.0 19.0 9.5
4.0 30.0 9.0 3.0 33.0 9.0
4.0
312/314/316/318/319
0.7 16.0 9.5 3.0 19.0 9.5
4.0 30.0 9.0 3.0 33.0 9.0
4.0
0.5 16.0 9.5 2.5
–
–
– 30.0 9.0 2.5 –
–
T
S
–
302
3.0 20.5 11.0 4.5 23.5 11.0 7.0 40.5 13.0 4.5 43.5 13.0 7.0
303/304
2.0 20.5 11.0 4.0 23.5 11.0 5.5 40.5 13.0 4.0 43.5 13.0 5.5
305/306/307
1.6 20.5 11.0 3.5 23.5 11.0 5.5 40.5 13.0 3.5 43.5 13.0 5.5
308/310
1.3 20.5 11.0 3.5 23.5 11.0 4.0 40.5 13.0 3.5 43.5 13.0 4.0
1.3 3.5 4.0 3.5
4.0
20.5 11.0 23.5 11.0 40.5 13.0 43.5 13.0
2.0 4.0 5.5 4.0 5.5
309
L
3.0
302
326/332
3T
2.5
302/303
312
1T
ø contact A
(mm)
Cable stripping lengths (mm)
M1
M2
Solder Crimp Solder Crimp
L S
T L S
T L S
T L S
312/314/316/318
0.9 20.5 11.0 3.0 23.5 11.0 4.0 40.5 13.0 3.0 43.5 13.0 4.0
320/322/324/326/330
0.7 20.5 11.0 3.0 23.5 11.0 4.0 40.5 13.0 3.0 43.5 13.0 4.0
Note:
1) crimp contacts are available only for connectors fitted with male contacts. The tolerances on these dim. are: L: ± 0.5 mm; S: ± 0.5 mm; T: ± 0.2 mm.
174
www.lemo.com
®
®
Cable stripping lengths for unipole connectors (S series)
M1
straight plugs and sockets with cable collet, clamping type C (solder contacts)
M3
elbow plugs (90°) with cable collet, clamping type C (solder contacts)
M6
elbow plugs (90°) with cable crimping type E (crimp contacts)
Type
00
0S
1S
2S
3S
4S
5S
M2
ø contact A
(mm)
straight plugs and sockets with cable crimping type E (crimp contacts)
L
T
4
19
5
7
7
4
5
4
–
–
–
8
5
1.3
9
116
1.6
11
120
130
130
140
140
160
140
160
112
2.0
3.0
3.0
4.0
4.0
6.0
4.0
6.0
12.0
Cable stripping lengths (mm)
M5
M3
Crimp
Solder
L
S
T
L
S
T
M1
Solder
S
113
13
13
18
18
21
21
25
25
12
4
8
8
9
9
9
9
9
9
15
5
5
6
6
7
9
7
9
12
–
–
–
–
–
–
–
–
–
–
–
–
–
15
–
–
–
–
–
–
–
13
–
–
–
–
–
–
–
13
15
19
19
23
23
–
8
8
9
9
9
9
9
9
–
2
L
17
M6
Crimp
S
T
2
–
–
–
2
2
2
2
2
2
2
2
–
–
–
–
–
–
–
–
–
–
5
–
–
–
–
–
–
–
–
–
7
–
–
L
T
–
–
–
S
–
–
–
–
straight plugs and sockets with oversize cable collet, clamping type K (solder contacts)
Type
00
0S
1S
2S
3S
4S
www.lemo.com
ø contact A
(mm)
M5
Cable stripping
lengths (mm)
L
M2
Solder
S
T
113
1.3
16
116
1.6
19
5
4
3.0
25
8
5
120
130
130
140
140
160
140
160
2.0
25
4
8
4
5
3.0
34
9
6
4.0
39
9
7
4.0
50
9
7
4.0
6.0
6.0
34
39
50
9
9
9
L
T
S
6
9
9
175
®
®
Cable stripping lengths for multipole connectors (S series)
M1
straight plugs and sockets with cable collet, clamping type C (solder or crimp contacts)
M3
elbow plugs (90°) with cable collet, clamping type C (solder or crimp contacts)
ø contact A
(mm)
L
302
0.9
10.0
5
3.5
15
5
4.0
10.0
5
3.5
15
5
4.0
303/304
0.7
10.0
5
3.5
15
5
4.0
10.0
5
3.5
15
5
4.0
302
1.3
12.5
8
3.5
17
8
4.0
14.5
8
3.5
17
8
4.0
303/304
0.9
12.0
8
3.0
17
8
4.0
14.0
8
3.0
17
8
4.0
305
0.9
0.7
12.0
8
3.0
17
8
4.0
14.0
8
3.0
17
8
4.0
306
0.7
12.5
8
3.0
17
8
4.0
14.5
8
3.0
17
8
4.0
302
1.6
17.0
9
3.5
22
9
5.5
17.0
9
3.5
22
9
5.5
303/304/305/306
1.3
17.5
9
3.5
22
9
4.0
17.5
9
3.5
22
9
4.0
307
1.3
0.9
17.5
9
3.5
3.0
22
9
4.0
17.5
9
3.5
3.0
22
9
4.0
308/310
0.9
17.0
9
3.0
22
9
4.0
17.0
9
3.0
22
9
4.0
302/303/304
2.0
20.0
9
4.0
–
–
–
–
–
–
–
–
–
305
2.0
1.3
20.0
9
4.0
3.5
–
–
–
–
–
–
–
–
–
306/307/308/310
1.3
20.5
9
3.5
–
–
–
–
–
–
–
–
–
312/313/314/316/318
0.9
20.0
9
3.0
–
–
–
–
–
–
–
–
–
302
4.0
25.0
9
7.0
–
–
–
–
–
–
–
–
–
303/304
3.0
23.5
9
4.5
–
–
–
–
–
–
–
–
–
305
3.0
2.0
23.5
9
4.5
4.0
–
–
–
–
–
–
–
–
–
306
2.0
21.0
9
4.0
–
–
–
–
–
–
–
–
–
307
2.0
1.3
21.0
9
4.0
3.5
–
–
–
–
–
–
–
–
–
308/309/310/312/313/314
1.3
24.5
9
3.5
–
–
–
–
–
–
–
–
–
316/318/320/322/324
0.9
24.5
9
3.5
–
–
–
–
–
–
–
–
–
Type
0S
1S
2S
3S
4S
176
Cable stripping lengths (mm)
M1
Solder
S
T
M3
L
Crimp
S
T
L
Solder
S
T
L
Crimp
S
T
L
T
S
www.lemo.com
®
®
Cable stripping lengths for multipole connectors (S series)
elbow plugs (90°) with cable collet, clamping type C (solder contacts)
Type
5S
302
303
304
305
306/308
310/312/316
314
318/322
320/324
6S
330/336/340/344/348
304
312/318
320/324
330/336/348
360
364/372
106
M4
ø contact A
(mm)
M3
straight plugs and sockets with cable collet, clamping type C (solder contacts)
Cable stripping lengths (mm)
M1
M3
Solder
Solder
T
L
S
T
L
S
6.0
33.5
22
7.5
33.5
22
7.5
4.0
33.5
22
5.5
33.5
22
5.5
6.0
4.0
4.0
3.0
3.0
2.0
3.0
2.0
3.0
1.6
1.6
1.3
33.5
33.5
33.5
32.0
33.5
33.5
34.0
34.5
22
22
22
22
22
22
22
22
7.5
5.5
5.5
4.5
4.5
4.0
4.5
4.0
4.5
3.5
3.5
3.5
33.5
33.5
33.5
32.0
33.5
33.5
34.0
34.5
22
22
22
22
22
22
22
22
7.5
5.5
5.5
4.5
4.5
4.0
4.5
4.0
10.0 37.0
15
10.0
3.0
37.0
15
6.0
15
6.0
2.0
1.6
1.3
0.9
37.0
37.0
37.0
37.0
15
15
15
15
15
7.0
37.0
7.0
37.0
4.5
4.0
4.0
37.0
37.0
37.0
37.0
15
15
15
15
15
S
3.5
15
37.0
T
3.5
37.0
4.0
L
4.5
3.5
8.0
7.0
7.0
4.5
4.0
4.0
straight plug with cable collet, clamping type D or M (solder or crimp contacts)
Type
2S
302
303/304/305/306
307
308/310
www.lemo.com
ø contact A
(mm)
M1
Cable stripping lengths (mm)
M4
Solder
Crimp
L
S
T
L
S
T
1.6
47.0
9
3.5
52
9
5.5
1.3
0.9
47.5
9
3.5
3.0
52
9
4.0
1.3
0.7
47.5
47.0
9
9
3.5
3.0
52
52
9
9
L
T
4.0
S
4.0
177
®
®
Cable stripping lengths for multipole connectors (S series)
straight plugs and sockets with oversize cable collet, clamping type K (solder or crimp contacts)
0S
1S
2S
3S
4S
5S
178
Type
ø contact A
(mm)
M2
302
0.9
19.5
5
3.5
23
5
4.0
303/304
0.7
20.0
5
3.5
23
5
4.0
302
1.3
24.5
8
3.5
28
8
4.0
303/304
0.9
24.0
8
3.0
28
8
4.0
305
0.9
0.7
24.0
8
3.0
28
8
4.0
306
0.7
24.5
8
3.0
28
8
4.0
302
1.6
33.0
9
3.5
38
9
5.5
303/304/305/306
1.3
33.5
9
3.5
38
9
4.0
307
1.3
0.9
33.5
9
3.5
3.0
38
9
4.0
308/310
0.9
33.0
9
3.0
38
9
4.0
302/303/304
2.0
38.0
9
4.0
–
–
–
305
2.0
1.3
38.0
9
4.0
3.5
–
–
–
306/307/308/310
1.3
38.5
9
3.5
–
–
–
312/313/314/316/318
0.9
38.0
9
3.0
–
–
–
302
4.0
50.0
9
7.0
–
–
–
303/304
3.0
48.5
9
4.5
–
–
–
305
3.0
2.0
48.5
9
4.5
4.0
–
–
–
306
2.0
49.0
9
4.0
–
–
–
307
2.0
1.3
49.0
9
4.0
3.5
–
–
–
308/309/310/312/313/314
1.3
49.5
9
3.5
–
–
–
316/318/320/322/324
0.9
49.0
9
3.0
–
–
–
302
6.0
68.5
22
7.5
–
–
–
303
6.0
4.0
68.5
22
7.5
5.5
–
–
–
304
4.0
68.5
22
5.5
–
–
–
305
4.0
3.0
68.5
22
5.5
4.5
–
–
–
306/308
3.0
68.5
22
4.5
–
–
–
310/312/316
2.0
67.0
22
4.0
–
–
–
314
3.0
2.0
68.5
22
4.5
4.0
–
–
–
318/322
3.0
1.6
68.5
22
4.5
3.5
–
–
–
320/324
1.6
69.0
22
3.5
–
–
–
330/336/340/344/348
1.3
69.5
22
3.5
–
–
–
Cable stripping lengths (mm)
M2
Solder
Crimp
L
S
T
L
S
T
L
T
S
www.lemo.com
®
®
Cable stripping lengths for unipole connectors (E series)
elbow plugs (90°) with cable collet, clamping type C (solder contacts)
Type
0E
1E
2E
3E
4E
5E
M2
116
120
130
ø contact A
(mm)
M3
straight plugs and sockets with cable collet, clamping type C (solder contacts)
1.6
2.0
3.0
Cable stripping lengths (mm)
M1
M3
Solder
Solder
T
L
S
T
L
S
9
5
4
20
5
4
13
8
5
25
8
5
12
8
5
25
8
5
3.0
16
9
6
33
9
6
4.0
19
9
7
40
9
7
160
6.0
23
9
9
50
9
9
112
12.0
12
15
12
–
–
–
130
140
140
160
4.0
6.0
15
20
9
9
6
9
33
9
40
L
T
6
9
9
S
straight plugs and sockets with oversize cable collet, clamping type K (solder contacts)
Type
1E
2E
3E
4E
www.lemo.com
120
130
130
140
140
160
160
ø contact A
(mm)
M1
Cable stripping
lengths (mm)
L
M2
Solder
S
T
26
8
5
2.0
25
3.0
28
4.0
36
6.0
50
3.0
4.0
6.0
27
37
8
9
9
9
9
9
5
L
T
6
6
7
S
9
9
179
®
®
Cable stripping lengths for multipole connectors (E series)
straight plugs and sockets with cable collet, clamping type C (solder or crimp contacts)
M3
elbow plugs (90°) with cable collet, clamping type C (solder or crimp contacts)
ø contact A
(mm)
M1
L
302
0.9
9.0
4
3.5
12
5
4.0
19.5
5
3.5
23
5
4.0
303/304
0.7
9.0
4
3.5
12
5
4.0
19.0
5
2.5
23
5
4.0
302
1.3
10.5
6
3.5
15
8
4.0
23.5
8
3.5
28
8
4.0
303/304
0.9
10.5
6
3.0
15
8
4.0
23.0
8
3.0
28
8
4.0
305
0.9
0.7
10.5
6
3.0
15
8
4.0
23.0
8
3.0
28
8
4.0
306
0.7
10.5
6
3.0
15
8
4.0
23.5
8
3.0
28
8
4.0
302
1.6
14.0
9
3.5
19
9
5.5
32.0
9
3.5
37
9
5.5
303/304/305/306
1.3
14.5
9
3.5
19
9
4.0
32.5
9
3.5
37
9
4.0
307
1.3
0.9
14.5
9
3.5
3.0
19
9
4.0
32.5
9
3.5
3.0
37
9
4.0
308/310
0.9
14.0
9
3.0
19
9
4.0
32.0
9
3.0
37
9
4.0
302/303/304
2.0
17.0
9
4.0
–
–
–
38.0
9
4.0
–
–
–
305
2.0
1.3
17.0
9
4.0
3.5
–
–
–
38.0
9
4.0
3.5
–
–
–
306/307/308/310
1.3
17.5
9
3.5
–
–
–
38.5
9
3.5
–
–
–
312/313/314/316/318
0.9
17.0
9
4.0
–
–
–
38.0
9
3.0
–
–
–
302
4.0
23.0
9
7.0
–
–
–
50.0
9
7.0
–
–
–
303/304
3.0
21.5
9
4.5
–
–
–
48.5
9
4.5
–
–
–
305
3.0
2.0
21.5
9
4.5
4.0
–
–
–
48.5
9
4.5
4.0
–
–
–
306
2.0
22.0
9
4.0
–
–
–
49.0
9
4.0
–
–
–
307
2.0
1.3
22.0
9
4.0
3.5
–
–
–
49.0
9
4.0
3.5
–
–
–
308/309/310/312/313/314
1.3
22.5
9
3.5
–
–
–
49.5
9
3.5
–
–
–
316/318/320/322/324
0.9
22.0
9
4.0
–
–
–
49.0
9
3.0
–
–
–
302
6.0
46.5
15
7.5
–
–
–
–
–
–
–
–
–
303
6.0
4.0
46.5
15
7.5
5.5
–
–
–
–
–
–
–
–
–
304
4.0
46.5
15
5.5
–
–
–
–
–
–
–
–
–
305
4.0
3.0
46.5
15
5.5
4.5
–
–
–
–
–
–
–
–
–
306/308
3.0
46.5
15
4.5
–
–
–
–
–
–
–
–
–
310/312/316
2.0
45.0
15
4.0
–
–
–
–
–
–
–
–
–
314
3.0
2.0
45.5
15
4.5
4.0
–
–
–
–
–
–
–
–
–
318/322
3.0
1.6
45.5
15
4.5
3.5
–
–
–
–
–
–
–
–
–
320/324
1.6
47.0
15
3.5
–
–
–
–
–
–
–
–
–
330/336/340/344/348
1.3
47.5
15
3.5
–
–
–
–
–
–
–
–
–
Type
0E
1E
2E
3E
4E
5E
180
Cable stripping lengths (mm)
M1
Solder
S
T
M3
L
Crimp
S
T
L
Solder
S
T
L
Crimp
S
T
L
T
S
www.lemo.com
®
®
Cable stripping lengths for multipole connectors (E series)
M3
straight plugs and sockets with cable collet, clamping type C (solder contacts)
elbow plugs (90°) with cable collet, clamping type C (solder contacts)
Type
6E
ø contact A
(mm)
M1
6.0
303
8.0
304
5.0
312
3.0
316/320/324
2.0
330/332/340/348
1.3
5.0
336
360/362
106
70
70
70
70
70
30
–
–
10.0
–
–
30
6.0
–
–
30
30
30
30
0.9
70
30
70
9.0
30
70
30
8.0
7.0
–
–
–
–
–
–
–
4.0
–
–
4.0
–
–
–
–
4.0
8.0
4.5
–
L
T
–
–
–
–
–
–
S
–
straight plugs and sockets with oversize cable collet, clamping type K (solder or crimp contacts)
Type
1E
ø contact A
(mm)
M2
70
1.6
1.3
364/372
Cable stripping lengths (mm)
M1
M3
Solder
Solder
T
L
S
T
L
S
302
303/304
305
306
2E
302
303/304/305/306
307
308/310
3E
302/303/304
305
306/307/308/310
4E
312/313/314/316/318
302
303/304
305
306
307
308/309/310/312/313/314
316/318/320/322/324
www.lemo.com
Cable stripping lengths (mm)
M2
Solder
Crimp
L
S
T
L
S
T
1.3
23.5
8
3.5
28
8
4.0
0.9
0.7
23.0
8
3.0
28
8
4.0
0.9
0.7
23.0
23.5
8
8
3.0
3.0
28
28
8
8
4.0
4.0
1.6
26.0
9
3.5
31
9
5.5
1.3
0.9
26.5
9
3.5
3.0
31
9
4.0
1.3
0.9
2.0
2.0
1.3
26.5
26.0
34.0
34.0
9
9
9
9
3.0
–
–
50.0
9
3.0
2.0
2.0
2.0
1.3
1.3
0.9
48.5
49.0
49.0
49.5
49.0
–
–
4.0
48.5
–
9
–
9
3.0
4.0
31
9
4.0
3.5
34.5
34.0
3.0
31
9
1.3
0.9
3.5
9
9
9
9
9
9
3.5
7.0
4.5
4.5
4.0
4.0
4.0
3.5
3.5
3.0
–
–
–
–
–
–
–
–
4.0
4.0
–
–
–
–
–
–
–
–
–
–
–
S
–
–
–
T
–
–
–
L
–
–
181
®
®
Technical characteristics
Outer shell
Brass
In most cases, LEMO connectors have a brass outer shell
which is suitable for most general purpose applications,
including civilian and military. The brass outer shells have
a chrome nickel-plated surface which ensures very good
protection against industrial atmosphere, salt air and most
corrosive agents.
Alternative protective coatings are available to satisfy other
specific environmental conditions:
– electrolytic nickel
– nickel-gold
– nickel-black chrome. After the black chrome treatment,
the part is coated with non conductive protective organic
film.
Stainless steel
For applications where there are severe environmental conditions that may rapidly damage the surface finish, we recommend using stainless steel. The AISI 303 stainless steel
is a material for general use adapted to most applications
requiring a product made entirely of stainless metal.
For the nuclear industry where elements are subject to
radiation and to vaporous nitric acid, we offer AISI 304
stainless steel.
Grade AISI 316L is recommended for medical applications,
highly demanding with regard to non-corrosiveness. This
material is also used for connector shells soldered by
electronic beam onto a device made of the same stainless
steel. These parts have no surface treatment.
Aluminium alloy
The aluminium alloy outer shells find numerous applications
where light weight is a predominant factor; such as in the
aeronautics and space industries, and for portable and
mobile equipment.
These materials have high mechanical strength and excellent
resistance to corrosion. The shell surface is protected by
anodizing which is available in six colours: blue, yellow,
black, red, green, and natural.
182
Plastic materials
Some connector model shells can be made of plastic. This
solution offers optimum electrical insulating properties
particularly suitable for medical applications. Black Polyoxymethylene (POM) is particularly adapted to products of
the 00 or S series.
Grey or white polysulfone (PSU) and beige PEEK offers
excellent mechanical properties and is suitable for gas or
vapour sterilization.
Some models of the 2B and 3B series are available with
an outer shell of cream-coloured polyphenylsulfone (PPSU).
We recommend this material particularly for applications
where products are to withstand hundreds of vapour
sterilization cycles.
Bridge plug or plugs with parallel sockets are made of
polyamide (PA.6) available in 9 colours: blue, white, grey,
yellow, brown, black, red, orange and green.
Some elbow socket shells for printed circuits are overmoulded
in polyphenilene sulfide (PPS).
Other metallic components
In general, most metallic components are manufactured in
brass. However, bronze or beryllium copper are used where
good elasticity is required (for example: earthing crown).
Depending on the application, these parts have electrolytic
nickel or nickel-gold plating.
These parts can also be manufactured in stainless steel.
Sealing gasket
In general, sealing gaskets are made of silicone rubber
MQ/MVQ. However, for vacuumtight sockets and couplers,
gaskets are made of fluorosilicone rubber (FPM).
Sealing resin
An epoxy resin is used to seal both watertight and vacuumtight
socket and coupler models.
www.lemo.com
®
®
Materials and Treatments
Component
Material (Standard)
Brass (UNS C 38500)
Stainless steel (AISI 303, 304 or 316L)
Aluminium alloy (AA 6262A or AA 6023)
Outer shell,
collet nut, conical nut
or notched nut and oversized collet
Aluminium alloy (AA 6262A or AA 6023)
chrome
Cu Ni Cr
0.5
3
–
–
Surface treatment (µm)
nickel
gold
black chr. Notes
Cu Ni Cu Ni Au Ni Cr
0.3 0.5
–
3
0.5
3
0.5
1
2
5
–
–
–
–
–
without treatment
–
POM (Delrin® or Ertacetal®), Polyoxymethylene, black
anodized
PEEK, Polyether ethercetone, beige
PSU
(Udel®),
PPSU (Radel®), Polyphenylsulfone, cream
Earthing crown
Latch sleeve
Locking washer
Hexagonal or round nut
Other metallic components
O-ring and gaskets
Sealing resin
Bronze (UNS C 54400) or special brass
Beryllium Copper (UNS C 17300)
Stainless steel (AISI 416 or 316L)
Special brass
Stainless steel (AISI 416 or 316L)
Bronze (UNS C 52100)
Brass (UNS C 38500)
Stainless steel (AISI 303, 304 or 316L)
Aluminium alloy (AA 6262A or AA 6023)
Brass (UNS C 38500)
Stainless steel (AISI 303, 304 or 316L)
Silicone MQ/MVQ or FPM/FKM (Viton®)
Epoxy (Araldite® or Stycast®)
–
4)
3)
4)
–
–
–
–
–
0.5
3
–
–
–
–
–
–
–
–
0.5
0.5
–
–
–
3
5)
0.5
0.5
3
3
without treatment
0.3 0.5
–
3
0.5
–
1.0
–
–
3
0.5
–
–
3
0.5
3
0.5
–
–
3
0.5
3
without treatment
anodized natural
0.5
–
0.5
without treatment
0.5
1.0
3
3
0.5
3
without treatment
Notes: standards for surface treatment are as follows:
– chrome-plated: SAE AMS 2460
– nickel-plated: SAE AMS QQ N 290, or MIL DTL 32119
– gold-plated: ISO 27874
– black chrome: MIL DTL 14538 with a minimum of 10 µm of lacquer protection
1) anthracite colour (other colours upon request)
2) for FFP, PCP and ERN models of the 0S to 3S series
3) for FFP, PCP and ERN models of the 0S to 3S series and FGG and ENG models of the 1B, 3B and 4B series
4) for the FGY and ENY models of the 2B and 3B series
5) for bridge plugs of the B series
6) for S and B series elbow sockets for printed circuits
7) gold-plating for unipole types
8) used in 00 series free and fixed sockets and couplers
9) AISI 416 steel is used with shells made of AISI 303 or 304
10) delivered with free and fixed sockets with aluminium alloy or stainless steel shell
11) FPM/FKM (Viton®) o-ring and gaskets are installed upon special request. However standard for vacuumtight models.
www.lemo.com
2)
–
PA.6 (Grilon®), Polyamid
PPS (Ryton®), Polyphenilene sulfide, brown
–
–
Polysulfone, grey or white
1)
–
–
0.5
0.5
–
–
–
–
6)
7)
8)
9)
9)
10)
10)
11)
183
®
®
Technical characteristics of plastic materials
Type
Standard
Units POM PEEK PSU PPSU PPS PA.6 Silicone FPM Epoxy
Density
ASTM D 792
Tensile strength (at 23°C)
ASTM D 638/ ISO R527 MPa
Flexurale strength (at 23°C)
ASTM D 790/ ISO R178 MPA
–
Dielectric strength
ASTM D 149/IEC 60243 kV/mm
60
Volume resis. at 50% HR and 23°C
ASTM D 257/IEC 60093 Ω l cm
1015
Surface resistivity
ASTM D 257
Thermal conductivity
ASTM C 177
Comparative tracking index
IEC 60112
–
1.24
1.3
1.67
1.14
~1.2
~1.9
1.58
70
70
121
55
> 9
> 12
16
170
106
91
179
75
–
–
24
19-25
17-20
15
17
35
18-30
–
15
1016
5x1016
–
1016
1015
1014
–
1014
Ω 1013
1015
–
–
–
– –
–
–
W/K l m 0.31
0.25
0.26
–
0.3
–
–
–
0.8
–
–
CTI>600
V
1.4
1.3-1.4
70-80 92-142
CTI 600 CTI 150 CTI 150
–
CTI 200 CTI 600
Maxi. continuous service temperature UL 746
°C
90
250
140
180
220
80
200
200
80
Min. continuous service temperature
UL 746
°C
-50
-55
-60
-50
-60
-40
-50
-20
-20
Max. short-time service temperature
°C
140
300
160
200
250
150
> 250
300
120
Water absorption in 24h at 23°C
ASTM D 570/ISO R62A
%
0.85
0.12
0.3
0.37
< 0.05
> 3
–
–
0.25
Gy1) 8x103
107
105
–
5x103
105
8x104
2x106
–
–
V-0/4
–
>
107
Radiation resistance
–
Flammability rating
ASTM D 635/UL 94
–
HB V-0/1.5 V-0/4.4 V-0/1.6 V-0/5V V-2
Resistance to steam sterilization
–
bad excel. good excel. excel. bad good good bad
–
Notes: 1) 1 Gy (Gray) = 100 rad.
ASTM = American Society for Testing Material
ISO = International Standards Organisation
184
UL
IEC
= Underwriters Laboratories
= International Electrotechnical Commission
www.lemo.com
®
®
Standard series
Fd
Fa
7
14
Fv
9
www.lemo.com
55
65 85 100
13 25
40 60
75
Force
(N)
Series
00 0B 1B 2B 3B 4B 5B
9
Fd
Fa
10
7
8
14 15
17
11 12
14
39
38
48
38
100 180 300 300 400 600 800
Keyed watertight series
Force
(N)
TT 0K 0T 1K
14
Fv
12
Fd
14 15
9
13
Series
1T 2K 2T 3K 3T 4K 5K
16 16
10 14
20 20
32 28
13 15
25 24
65 85
40 60
80 250 130 300 250 400 250 550 400 700 800
Fa
(dBOhm)
5
(dB)
30
40
-5
50
-10
60
-15
70
-20
80
-25
90
-30
100
-35
110
FGG + PHG.1B
1G
500 M
200 M
50 M
100 M
Frequency
20 M
Transfer impedance
Shielding efficiency
0
5M
The design of LEMO connectors with metal shell and earthing crown guarantee optimum shielding efficiency in all
applications where electromagnetic compatibility (EMC) is
critical. The performance of a connector is measured through
shielding efficiency, a value that represents the ratio between
the electromagnetic field on the outside and the inside of
the shell. Our measurements are carried out according to
the IEC 60169-1-3 standard.
70
Keyed series
10 K
When selecting a connector, screen or shielding efficiency
and low resistance to electric continuity between the cable
and the connector should be considered.
10
20 32
250 300 400 550 700 800 900
The electromagnetic compatibility of a device can only be
ensured by meeting a number of basic rules with the design
of the device and by carefully selecting components, cables
and connectors.
a) reduce the emission of generated electromagnetic
disturbance to a level where radios and telecommunication
and other devices can properly function;
b) electromagnetic immunity against electromagnetic
disturbance so that they can properly function.
40
Fa
Electromagnetic compatibility (EMC)
and shielding efficiency
Electrical and electronic devices are to be designed to ensure
the following:
25
60
10 M
1N = 0.102 kg.
16
2M
Notes: forces were measured on outer shells not fitted with contacts.
Mechanical endurance: 5000 cycles (3000 cycles for T series).
The values were measured according to the standard IEC 60512-7 test 13a.
14
500 K
1M
Fa: average pull force with axial pull on the collet nut
10 11
40
Series
0E 1E 2E 3E 4E 5E 6E
Force
(N)
20 K
Fd: average unmating force with axial pull on
the outer shell.
9
20
120 140 250 350 500 650 750 900
Fv
Fv: average latching force.
15 17
Watertight series
Fd
Fa
14
200 K
Fd
9
Fv
50 K
Fv
Series
00 0S 1S 2S 3S 4S 5S 6S
Force
(N)
100 K
Mechanical latching characteristics
(Hz)
FGG + PHG.1K
The performance of S and B series connectors is comparable to the results of measurements carried out on a pair
of FGG + PHG.1B connectors.
The performance of E and K series connectors is comparable to the results of measurements carried out on a pair
of FGG + PHG.1K connectors.
185
®
®
Shell electrical continuity:
(measured according to IEC 60512-2 test 2f)
Test current: 1A
A = Ammeter
mV = Millivoltmeter
G = Generator
Standard series
Values with earthing crown and latch sleeve or inner-sleeve nickelR1 plated.
Values with gold-plated earthing crown and nickel-plated latch sleeve
R2 or inner sleeve.
Series
00
0S
1S
A
mV
2S
G
Keyed series
Series
00
0B
1B
XB
A
mV
G
2B
3B
4B
5B
Watertight series
Keyed watertight series
Series
0E-0K
1E-1K
2E-2K
A
mV
3E-3K
G
4E-4K
5E-5K
6E
186
R1
(mΩ)
R2
(mΩ)
Series
2.8
1.6
4S
3.5
2.2
1.8
2.8
1.5
1.2
3S
5S
6S
R1
(mΩ)
R2
(mΩ)
Series
3.5
1.3
0T
3.5
2.5
2.5
2.2
2.2
1.5
1.5
2.8
1.1
1.1
0.9
0.7
0.5
0.3
R1
(mΩ)
R2
(mΩ)
2.2
1.5
2.8
1.8
1.6
1.4
1.4
1.0
TT
1T
2T
3T
4T
5T
R1
(mΩ)
R2
(mΩ)
1.4
1.0
1.6
1.4
1.0
1.2
1.0
0.5
R1
(mΩ)
3.5
3.5
2.5
2.2
2.2
1.5
1.5
1.6
1.2
1.2
1.0
1.0
0.5
www.lemo.com
®
®
Insulator
Plastic material used by LEMO for manufacturing insulators
is selected according to the electric and thermal properties
required for the various connector types.
Characteristics examined for the two connector types are:
Dielectric strength, Comparative tracking index,
Surface and volume resistivity, Radiation resistance,
Continuous service temperature, Water absorption,
Flammability rating, Resistance to hydrocarbon.
Radiation resistance
Mechanical and Electrical Properties
PI
Mechanical characteristics of thermoplastics, such as PA
6.6, and PEEK, are improved by the addition of glass fibres.
By adding glass fibres in the resin the performance of this
material (mechanical strength and radiation resistance) is
enhanced and water absorption rate is reduced. From an
electric point of view, the addition of glass fibres improves
dielectric strength.
103
rads
Gray (Gy) 101
PA 6.6
PEEK
PTFE
FEP
104 105 106 107 108 109 1010
102 103 104 105 106 107 108
Radiation dose γ
Damage
Minimum to slight (almost available usable)
Slight to medium (often satisfactory)
Medium to serious (not usable)
Selection of the insulator
Note: technical data in this chapter provide general information on plastics
used by LEMO as electrical insulators. LEMO reserves the right to propose new materials with better technical characteristics, and to withdraw,
without notice, any material mentioned in the present catalogue or any
other publications edited by LEMO S.A. and/or its subsidiaries. LEMO SA
and its subsidiaries use only plastic granules, powder or bars supplied by
specialized companies, and thus cannot in any case take responsibility
with regard to this material.
A number of thermoplastics have common characteristics,
some of them are identical with other insulating materials.
In this case, the insulator material is selected according to
the specific difference in features to provide all the required
parameters for the given type.
Technical characteristics
Type
Dielectric strength
Standard
ASTM D 149 / IEC 60243
Units PA6.6 PEEK PTFE FEP
20
PI
kV/mm
15-17
19-25
17.2-24
Ω l cm
5.8x1015
1016
1018
>
1016
22
> 1016
1015
1017
> 1016
> 1015
Volume resistivity at 50% RH and 23°C
ASTM D 257 / IEC 60093
Surface resistivity
ASTM D 257 / IEC 60093
Thermal conductivity
ASTM C 177
Comparative tracking index
IEC 60112
V
CTI 600
CTI 150
CTI 500
–
–
Dielectric constant (106 Hz)
ASTM D 150 / IEC 60250
–
4
3.2-3.5
2-2.1
2.1
3.6
Dissipation factor (106 Hz)
ASTM D 150 / IEC 60250
–
–
< 0.005 < 0.0003 < 0.001
Maximum continuous service temperature
UL 746
°C 120 250 260 200 350
Maximum short-time service temperature
–
°C 150 300 300 260 480
Minimum continuous service temperature
–
°C
Water absorption in 24h at 23°C
ASTM D 570 / ISO R624
%
Radiation resistance
Gy 5x103
Flammability rating
ASTM D 635 / UL 94
Designation
chemical commercial
Symbol
Ω 1012
W/K l m
0.21 0.25 0.23 0.24 0.35
–
Standard
< 0.7
–
–
-55 -200 -200 –
< 0.3
< 0.01
< 0.01
0.24
107
2x102
2x104
106
V-0/1.5
V-0
V-0
–
Unipole
Multipole
00 S E 00 S E B K T
l
l
l
l l
l
l
– l
l
Polyamide (glass fitted)
Nylatron®
PA 6.6
Polyether Ethercetone
Peek®
l l
PEEK –
–
l
l
l
l
PTFE
ASTM D 1457-83
Tetrafluorethylene –
FEP
ASTM D 2116-81
Polyimide Vespel®
PI
Note: values of insulation resistance between contacts are given on page 189.
l
l
l
Polytetrafluorethylene –
www.lemo.com
–
< 0.0034
l First choice alternative
l Special order alternative
187
®
®
Electrical contact
Technical description
The secure reliable electromechanical connection achieved
with LEMO female cylindrical contacts is mainly due to
two important design features :
1. Prod proof entry on the mating side which ensures
perfect concentric mating even with carelessly handled
connectors.
2. The pressure spring, with good elasticity, maintains a
constant even force on the male contact when mated.
The leading edge of the pressure spring preserves the
surface treatment (gold-plated) and prevents undue
wear.
Contact material and treatment
LEMO female contacts are made of bronze beryllium (QQC-530) or bronze (UNS C 54400). These materials are chosen
because of their high modulus of elasticity, their excellent
electrical conductivity and a high mechanical strength.
Au
Ni
Cu
LEMO male solder and print contacts are made of brass
(UNS C 38500). Male crimp contacts are made of brass
(UNS C 34500) or annealed brass (UNS C 38500) with
optimum hardness (HV) for crimping onto the wire.
Type
Male crimp
Bronze
or brass
Female crimp / print
Clips
Connection
wire2)
Thickness comparison between the outside and the inside of female contacts
P
Contact
øA
(mm)
male
(µm)
0.50
1.0
0.35
2.5
P
2.5
0.70
0.90
1.30
1.60
Note: P = inspection point
188
2.00
1.0
1.0
1.0
1.0
1.0
1.0
Gold thickness
female
outside
(µm)
inside
(%)
1.5
65
1.5
1.5
1.5
1.5
1.5
1.5
Notes: 1) contacts are silver plated
Brass (UNS C 34500)
Brass (UNS C 38500)
Male print
Notes: the standard surface treatment are as follows:
– nickel: SAE AMS QQ N 290 or MIL DTL 32119
– gold: ISO 27874.
1) minimum value
2) for elbow print contacts
3) treatment completed by 6 µm Sn (lead free) tin-plating
Material (standard)
65
70
75
75
75
75
Brass (UNS C 38500)
Bronze (UNS C 54400)
Cu-Be (FS QQ-C-530)
Cu-Be (FS QQ-C-530)
Stainless steel
Brass
male
(µm)
4.00
1.0
5.00
6.00
8.00
12.001)
0.5
3
1.0
0.5
3
1.0
0.5
3
1.0
1.0
1.0
1.0
–
1.0
0.5
3
1.5
–
–
–
–
–
–
Contact
øA
(mm)
3.00
Surf. treatment (µm)
Cu
Ni
Au1)
–
33)
–
Gold thickness
female
outside
(µm)
inside
(%)
1.5
75
1.5
1.5
1.5
1.5
–
75
75
75
75
–
www.lemo.com
®
Contact resistance with relation to the number
of mating cyles
(measured according to IEC 60512-2 test 2a)
Average values measured after the mating cycles and
the salt spray test according to IEC 60512-6 test 11f.
Aø
(mm)
0.35
0.5
0.7
0.9
1.3
1.6
2.0
Contact resistance (mΩ)
1000
cycles
3000
cycles
5000
cycles
7.5
8.3
8.7
4.1
4.2
4.8
8.0
5.6
2.8
2.9
2.6
–
5.7
2.9
3.1
2.7
–
6.1
3.6
3.5
3.3
Aø
(mm)
3.0
4.0
5.0
6.0
8.0
12.0
Contact resistance (mΩ)
1000
cycles
3000
cycles
5000
cycles
1.6
2.0
2.8
2.0
1.4
1.2
0.8
0.7
2.2
–
–
–
–
3.1
–
®
Insulation resistance between the contacts
and contact/shell
(measured according to IEC 60512-2 test 3a)
Multipole
PEEK
Insulating material
new
after humidity
> 1012 Ω
test1)
>
1010
Ω
Unipole
PTFE
> 1012 Ω
> 1010 Ω
Note: 1) 21 days at 95% RH according to IEC 60068-2-3.
–
–
–
Solder contacts
The conductor bucket of these contacts is machined at an
angle to form a cup into which the solder can flow.
See page 8 for the range of cable dimensions that can be
soldered.
Crimp contacts
The square form crimp method is used (MIL-C-22520F,
class I, type 2) photo 1 for unipole contacts.
For multipole contacts the standard four identer crimp
method is used, MIL-C-22520F, class I, type 1), photo 2.
The crimp method requires a controlled compression to
obtain a symmetrical deformation of the conductor strand
and of the contact material. The radial hole in the side of
the contact makes it possible to check whether the conductor
is correctly positioned within the contact. A good crimping
is characterized by only slightly reduced conductor section
and practically no gap.
For optimum crimping of bronze or brass contacts they are
annealed to relieve internal stress and reduce material
hardening during the crimping process.
Only the crimping zone is annealed with the help of an
induction heating machine designed by the LEMO Research
and Development Department (see photo 3).
Crimp contacts
The crimp contacts can be with two forms: a standard crimp
barrel for large conductors (see fig. 1) or with a reduced
crimp barrel for smaller conductors (see fig. 2).
Fig. 1
www.lemo.com
Advantages of crimping
– practical, quick contact fixing outside the insulator
– possible use at high temperature
– no risk of heating the insulator during the conductorcontact fixing
– high tensile strength
Crimp contacts are available in standard version (form 1)
for mounting maximum size conductors.
For some dimensions, these crimp contacts can be produced
with reduced crimp barrels (form 2) for mounting reduced
size conductors.
1
2
3
The range of cable dimensions that can be crimped into
our contacts are indicated on the table on page 8.
Fig. 2
189
®
®
Print contacts
Print contacts are available in straight or elbow versions
for certain connector types, mostly for straight and elbow
socket models. Connection is made on flexible or rigid
printed circuits by soldering.
Straight print contacts are gold-plated which guarantees
optimum soldering, even after long-term storage. However
straight
for wave soldering, we recommend removal the gold-plating from the contact end on the printed circuit side before
soldering according to the assembly procedures.
Print elbow contacts include a tinned lead free brass wire
crimped into a crimp contact.
elbow
Test voltage
Test voltage (Ue) :
(measured according to the IEC 60512-2 test 4a standard)
It corresponds to 75% of the mean breakdown voltage.
Test voltage is applied at 500 V/s and the test duration is
1 minute.
This test has been carried out with a mated plug and socket,
with power supply only on the plug end.
The operating voltage value definition is at the entire
responsibility of the customer who defines this value
according to the safety factors that they apply to their
equipment and system.
Caution:
For a number of applications, safety requirements for
electrical appliances are more severe with regard to
operating voltage.
In such cases operating voltage is defined according
to creepage distance and air clearance) between live parts.
Please consult us for the choice of a connector by indicating the safety standard to be met by the product.
Voltage values are given in the table on insulator types for
each series.
They correspond with values measured at sea level. They
are adapted to all applications up to an altitude of 2000 m.
In case a device is used at a higher altitude, air clearance
between live parts has to be multiplied by the following
coefficients.
It means also that test voltage has to be divided by this
coefficient.
altitude (m)
coefficient
2000
1.00
3000
1.14
4000
1.29
5000
1.48
Rated current
Rated current (A)
The current values are indicated in the table of insulator
types in each series.
For use at higher temperatures acceptable rated current will
be lower. It tends towards zero as the material is used at the
maximum operating temperature accepted for the insulator.
100%
In most case the current depend on the conductor dimension
(see table on page 196) or on the printed circuit dimension.
50%
Caution:
In general, connectors should not be unmated while live.
190
75%
25%
0
for the insulator
The specified rated current can be applied simultaneously
to all the contacts.
It corresponds with an average temperature rise of 40°C
of the connector.
For connectors with PEEK insulator, maximum admissible
current will follow the curve below depending on the operating temperature T.
Maximum operating temperature
(measured according to IEC 60512-3 test 5a)
T (°C)
50
100
150
200
250
www.lemo.com
®
®
Cable fixing
Cables are fixed into LEMO connectors with cable collet systems. These collets with latches have a design which is very
similar to those used for tool machines. This solution guarantees excellent cable retention and ensures perfectly symmetrical
deformation of the cable.
The 00 multipole series is also available with hexagonal crimping (MIL-C-22520F).
Material and treatment
Component
Center piece
Collet
Crimp ferrule
Reducer
Reducing cone
Earthing cone
Metal washer
Gasket
Material (standard)
Brass (UNS C 38500)
Surface treatment (µm)
Nickel1)
Gold
Cu
Ni
Cu
Ni
Au
0.5
Brass (UNS C 38500)
0.5
Brass (UNS C 38500)
0.5
3
3
Copper (UNS C 18700) 0.5
Brass (UNS C 38500)
Brass (UNS C 38500)
Brass (UNS C 38500)
Silicone MQ/MVQ
3
3
0.5
3
0.5
3
0.5
3
FPM (Viton®)2)
–
–
0.5
3
–
–
–
–
–
–
–
–
–
–
–
–
–
0.5
–
–
–
–
Notes:
1) standards for surface treatment are as follows:
– nickel-plated: SAE AMS QQ N 290.
2) available upon special request.
–
Cable clamping system
B series (D and M cable clamping)
See assembly instructions under www.lemo.com.
6
7
5
Type D
1
3
7
6
5
4
3
Type M
9
7
6
5
2
1
Plug and socket
¿ collet nut
¡ reducing cone
¬ collet
√ reducer
ƒ split insert carriers
≈ insulator + contacts
∆ housing subassy.
Elbow plug
¿ collet nut
¡ reducing cone
¬ collet
√ reducer
ƒ elbow outlet
≈ insert carrier
∆ insulator + contacts
« housing subassy.
» hex cap
8
www.lemo.com
191
®
®
K series (C and K cable clamping)
See assembly instructions under www.lemo.com.
7
6
5
7
1
Type C
6
4
3
2
1
5
9
7
8
6
Type K
7
5
6
3
Elbow plug
¿ collet nut
¡ collet
¬ flexible gasket
√ earthing cone
ƒ split insert carrier
≈ elbow inner shell
∆ insulator + contacts
« hex cap
» housing subassy.
Plug and socket
¿ collet nut
¡ collet
¬ flexible gasket
√ earthing cone
ƒ split centre-pieces
≈ insulator + contacts
∆ housing subassy.
w. oversized back
1
4
Plug and socket
¿ collet nut
¡ collet
¬ flexible gasket
√ earthing cone
ƒ split insert carriers
≈ insulator + contacts
∆ housing subassy.
2
1
T series (C cable clamping)
See assembly instructions under www.lemo.com.
7
6
5
1
Type C
4
3
2
1
7
192
6
5
Plug and socket
¿ collet nut
¡ collet
¬ flexible gasket
√ earthing cone
ƒ split insert carriers
≈ insulator + contacts
∆ housing subassy.
www.lemo.com
®
®
S series (C, L and K cable clamping)
See assembly instructions under www.lemo.com.
1
Type K
2
3
5
6
7
Plug and socket
¿ collet nut
¡ collet
¬ oversize collet
housing (type K)
√ earthing
centre-piece (type C)
ƒ split centre-pieces
(type K and C)
≈ insulator + contacts
∆ housing subassy.
1
6
F ●●
Type L*
2
6
1
7
4
1
Type C
2
6
5
P ●●
6
7
5
4
6
* «L» type collet does not allow to connect the screen to
the connector shell. It does not allow full EMC shielding.
8
FLA
Elbow plug
¿ collet nut
¡ collet
√ threaded sleeve
ƒ bracket
≈ insulator + contacts
∆ insulating sleeve
« housing subassy.
E series (C and K cable clamping)
See assembly instructions under www.lemo.com.
Type K
7
8
2
3
4
5
6
1
7
1
5
7
8
6
7
4
Type C
3
1
2
5
9
FLA
www.lemo.com
7
6
8
1
Plug and socket
¿ collet nut
¡ collet
¬ flexible gasket
√ earthing cone
ƒ split centre-pieces
(type K)
ƒ earthing
centre-piece (type C)
≈ oversize collet
housing (type K)
≈ earthing
centre-piece (type C)
∆ insulator + contacts
« housing subassy.
Elbow plug
¿ collet nut
¡ collet
¬ flexible gasket
√ earthing cone
ƒ split insert carrier
≈ elbow inner shell
∆ insulator + contacts
« hex cap
» housing subassy.
193
®
®
Maximum metal collet nut tightening torque
Standard series
Torque (Nm)
00
0S
0.25 0.5
Keyed series
Torque (Nm)
00
0B
0.25 0.5
1S
Series
2S 3S
1.5
2.5
1B
Series
XB 2B
1.5
2.0
3
2.5
4S
5S
8
10
3B
4B
4
7
Watertight series
6S
Torque (Nm)
12
Torque (Nm)
00
0B
1B
0.2 0.25 0.5
Series
2B 3B
0.5
1.5
4B
3
5B
10
5B
Torque (Nm)
194
0S
1S
2S
Series
3S 1B
2B
Torque (Nm)
0.8
TT 0K
2E
2
0T
0E
0.8
1E
3B
4B
0.15 0.45 0.50 0.50 1.00 0.50 0.50 1.00 1.50
3
1K
1
Series
2E 3E
1.2
Watertight keyed series
Torque (Nm)
Series
3E 4E
0K
0.8
1K
1
1.5
Series
2K 3K
1.2
1.5
5E
5
1T
0.25 0.7 0.7 0.8 0.8
Watertight series
Torque (Nm)
5
Maximum plastic collet nut tightening torque 1)
00
0.7
1E
Watertight keyed series
Maximum elbow plug hex cap tightening torque
Keyed series
0E
6E
8
12
Series
2K 2T
2
2
4E
5E
4K
5K
3
3
3K
3
3T
3
4K
5
5K
8
5
5
1N = 0.102 kg
Note:
1) For applications subject to strong vibration, we recommend fixing the collet nut
with epoxy resin. We recommend to tight to the maximum value. Optimal torque
may depend on cable jacket design.
www.lemo.com
®
®
Technical tables
Table of American Wire Gauge
Construction
AWG
Strand
nb
AWG/
strand
1
817
30
0
2
4
6
8
8
10
10
10
259
259
133
133
168
133
105
37
1
12
37
12 1)
7
12
12
19
1
14
41
14 1)
7
14
14
19
1
16 1)
65
16
19
16
16 1)
16
26
7
1
18 1)
65
18
19
18 1)
18
18
18
42
16
7
1
www.lemo.com
ø wire max
(mm)
(in)
Wire section
(mm2)
(sq in)
24
11.277
0.444
52.90
0.0820
26
8.89
0.35
33.20
0.0514
25
27
30
29
30
26
10
28
25
20
12
30
27
22
14
34
30
29
24
16
36
34
30
30
26
18
9.702
0.382
6.9596
0.274
4.4450
0.175
5.5118
4.3942
3.3020
0.217
0.173
0.13
2.9210
0.115
2.3114
0.091
2.6162
2.3622
2.5400
0.103
0.093
0.10
2.0828
0.082
1.8542
0.073
2.0574
2.0828
1.6510
1.5748
1.5748
1.4986
1.5494
1.3208
1.2700
1.2700
0.081
0.082
0.065
0.062
0.062
0.059
0.061
0.052
0.05
0.05
1.3208
0.052
1.2700
0.05
1.2954
1.0414
0.051
0.041
41.40
21.5925
13.5885
8.5127
8.6053
5.3204
4.7397
5.2614
2.9765
3.0847
3.6321
3.3081
2.0775
1.9413
2.2704
2.0820
1.3072
1.3174
1.2293
1.4330
1.3076
0.8234
0.8447
0.9627
0.8107
0.8967
0.8229
0.0641
0.0335
0.0211
0.0132
0.0133
0.0082
0.0073
Construction
AWG
Strand
nb
AWG/
strand
20
19
32
20
7
22
19
22
1
20 1)
20
20
22
24 1)
42
10
1
7
42
ø wire max
(in)
(mm2)
1.0414
0.041
0.6162
0.0010
28
0.9906
0.039
0.5631
8.7x10-4
34
0.8382
0.033
0.3821
5.9x10-4
0.6604
0.026
36
30
20
30
22
40
(mm)
Wire section
1.0160
1.0160
0.8382
0.7874
0.6604
0.04
0.04
0.033
0.031
0.026
0.5320
0.5067
0.5189
0.3547
0.3243
0.2045
(sq in)
8.2x10-4
7.9x10-4
8.0x10-4
5.5x10-4
5.0x10-4
3.2x10-4
0.0082
24
19
36
0.6858
0.027
0.2407
3.7x10-4
0.0048
24
1
24
0.5588
0.022
0.2047
3.2x10-4
0.0046
0.0056
0.0051
0.0032
0.0030
24
26
19
26
1
26
19
28
1
28
0.0020
30
0.0020
0.0019
0.0022
0.0020
0.0013
0.0013
0.0015
0.0013
0.0014
7
28 1)
0.0035
0.0032
7
30
32
32
34
36
38
40
7
7
1
7
1
1
1
1
1
32
38
34
26
40
36
28
38
30
40
32
34
36
38
40
0.6350
0.025
0.2270
0.5588
0.022
0.4318
0.017
0.1281
2.0x10-4
0.016
0.0887
1.4x10-4
0.5080
0.02
0.4318
0.017
0.3302
0.013
0.4064
0.3302
0.2794
0.2794
0.2286
0.1693
0.127
0.1016
0.078
Note: 1) not included in the standard
0.013
0.011
0.011
0.009
0.007
0.005
0.004
0.003
0.1540
3.5x10-4
0.1408
0.0925
0.0804
0.0568
0.0507
0.0341
0.0324
0.0201
0.0127
0.0081
0.0049
2.4x10-4
2.2x10-4
1.4x10-4
1.2x10-4
8.8x10-5
7.9x10-5
5.3x10-5
5.0x10-5
3.1x10-5
2.0x10-5
1.3x10-5
7.5x10-6
0.0013
195
®
®
Table of wire gauges according to IEC-60228 standard
Conductor no
x Ø (mm)
196x0.40
Conductor no
x Ø (mm)
Max Ø
(mm)
Max Ø
(in)
Section
(mm2)
Section
(sq in)
6.10
0.240
25.00
0.0387
32x0.20
0.0248
1x1.15
7.50
7x2.14
125x0.40
6.00
7x1.72
4.90
1x4.50
4.50
80x0.40
4.70
7x1.38
3.95
1x3.60
3.60
84x0.30
3.70
7x1.50
3.15
1x2.76
2.76
56x0.30
2.80
7x0.86
2.58
1x2.25
2.25
50x0.25
2.15
7x0.68
2.04
1x1.78
1.78
30x0.25
1.60
7x0.52
1.56
0.295
0.236
0.192
0.177
0.155
0.155
25.00
16.00
16.00
16.00
10.00
10.00
0.141
10.00
0.124
6.00
0.145
0.108
0.110
0.098
0.082
0.084
0.080
0.070
0.062
0.061
6.00
6.00
4.00
4.00
4.00
2.50
2.50
2.50
1.50
1.50
0.0387
0.0248
1x1.40
7x0.43
0.0248
42x0.15
0.0155
1x1.00
0.0155
28x0.20
0.0155
28x0.15
0.0093
1x0.80
0.0093
0.0093
0.0062
1.35
0.053
1.00
0.0015
1.40
1.29
1.15
1.20
1.15
1.00
0.95
0.055
0.050
0.045
0.047
0.045
0.039
0.037
1.50
1.00
1.00
0.75
0.75
0.75
0.50
0.0023
0.0015
0.0015
0.0011
0.0011
0.0011
7.7x10-4
0.50
7.7x10-4
7x0.25
0.75
0.029
0.34
5.2x10-4
1x0.60
18x0.10
0.0038
21x0.07
0.0023
Section
(sq in)
0.035
0.0038
0.0023
Section
(mm2)
0.90
14x0.15
0.0038
Max Ø
(in)
16x0.20
0.0062
0.0062
Max Ø
(mm)
7x0.20
14x0.10
14x0.10
0.80
0.60
0.75
0.65
0.50
0.40
0.40
0.40
0.031
0.023
0.029
0.023
0.019
0.015
0.015
0.015
0.50
0.28
0.25
0.22
0.14
0.11
0.09
0.09
7.7x10-4
4.3x10-4
3.8x10-4
3.4x10-4
2.1x10-4
1.7x10-4
1.3x10-4
1.3x10-4
Maximum current rating for conductor
Maximum current on insulated conductors up to an ambiant temperature of 30° C (from VDE 0100, parts 430 and 532 as
well as other VDE regulations).
Nominal
section
mm2
0.08
0.14
0.25
0.34
0.50
1.0
2.0
4.0
6.0
1.5
3.0
5.0
8.0
12.0
15.0
19.0
12.0
1.50
18.0
2.50
Group 3
Intens.
max. A
9.0
0.75
1.00
196
Group 2
Intens.
max. A
26.0
15.0
24.0
32.0
Group 2 Multi-conductor, e. g. solid cable under sheath, shielded cable, lead-sheath cables, …
Group 3 Single conductor and single conductor cable laid on open air in a way to leave at least a
space between them equal to their diameter
www.lemo.com
®
Some formulae
Resistance R of a conductor: R = ρ
Impedance of coaxial line:
Z =
l
l
[Ω]
A
Conversion of some units:
millimeters into inches:
1 cm = 0.0328 ft
feet (12 in) into centimeters:
square centimeters into square inches:
square inches into square centimeters:
bar into pounds per square inch:
bar into Pascal:
newtonmeter (Nm) into inch pound (in lb)
www.lemo.com
l
1 ft = 30.48 cm
1 cm2 = 0.155 sq in
1 sq in = 6.4516 cm2
1 bar = 14.51 psi
1 bar = 105 Pa
°C into °F:
l
U1 = input signal voltage
U2 = output signal voltage
1 in = 25.4 mm
centimeters into feet:
l
U1
[dB]
U2
1 mm = 0.0394 in
inches into millimeters:
l
εr = dielectric constant
D = dielectric outer diameter
d = center conductor outer diameter
l
l
mbar l s-1 into Torr l s-1
Where: ρ = conductor resistivity
l = conductor length
A = conductor cross-section
138
D
log [Ω]
√εr
d
Signal attenuation: Attenuation = 20 log
®
l
°F = °C 1.8 + 32
l
1 Nm = 8.85 in lb
l
1 mbar l s-1 = 1.33 Torr l s-1
l
l
l
l
197
®
®
Product safety notice
PLEASE READ AND FOLLOW ALL INSTUCTIONS CAREFULLY AND CONSULT ALL RELEVENT NATIONAL AND
INTERNATIONAL SAFETY REGULATIONS FOR YOUR APPLICATION.
IMPROPER HANDLING, CABLE ASSEMBLY, OR WRONG USE OF CONNECTORS CAN RESULT IN HAZARDOUS
SITUATIONS.
1. SHOCK AND FIRE HAZARD
Incorrect wiring, the use of damaged components, presence of foreign objects (such as metal debris), and / or residue
(such as cleaning fluids), can result in short circuits, overheating, and / or risk of electric shock.
Mated components should never be disconnected while live as this may result in an exposed electric arc and local
overheating, resulting in possible damage to components.
2. HANDLING
Connectors and their components should be visually inspected for damage prior to installation and assembly. Suspect
components should be rejected or returned to the factory for verification.
Connector assembly and installation should only be carried out by properly trained personnel. Proper tools must be used
during installation and / or assembly in order to obtain safe and reliable performance.
3. USE
Connectors with exposed contacts should never be live (or on the current supply side of a circuit). Under general
conditions voltages above 30 VAC and 42 VDC are considered hazardous and proper measures should be taken to
eliminate all risk of transmission of such voltages to any exposed metal part of the connector.
4. TEST AND OPERATING VOLTAGES
The maximum admissible operating voltage depends upon the national or international standards in force for the
application in question. Air and creepage distances impact the operating voltage; reference values are indicated in the
catalog however these may be influenced by PC board design and / or wiring harnesses.
The test voltage indicated in the catalog is 75% of the mean breakdown voltage; the test is applied at 500 V/s and the
test duration is 1 minute.
5. CE MARKING
CE marking
means that the appliance or equipment bearing it complies with the protection requirements of one or
several European safety directives.
CE marking
applies to complete products or equipment, but not to electromechanical components, such as
connectors.
6. PRODUCT IMPROVEMENTS
The LEMO Group reserves the right to modify and improve to our products or specifications without providing prior
notification.
7.
WARNING (Prop 65 State of California)
Proposition 65 requires businesses to provide warnings to Californians about significant exposures to chemicals that
cause cancer, birth defects or other reproductive harm. LEMO products are exempt from proposition 65 warnings because
they are manufactured, marketed, and sold solely for commercial and industrial use. For further information, please visit
https://www.lemo.com/quality/LEMO-Prop-65-compliance-declaration.pdf.
198
www.lemo.com
®
®
Disclaimers
LEMO works constantly to improve the quality of its products; the information and illustrations figuring in this document
may therefore vary and are not binding. In any case, LEMO makes no specific warranty of merchantability, fitness for a
particular purpose, third party components as such or included in assembly, non-infringement, title, accuracy, completeness,
or security. The user is fully responsible for his products and applications using LEMO component.
In no event shall LEMO, its affiliates, officers, agents or employees be liable for any incidental, indirect, special or
consequential damages in connection with the products or services provided by LEMO, including (without limitation) loss
of profits or revenues, interruption of business, loss of use of the products or any associated equipment, materials,
components or products, damages to associated equipment or in combination with other components, materials.
Reproduction of significant portions of LEMO information in LEMO data books or data sheets is permissible only if
reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices.
LEMO is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
www.lemo.com
199
®
®
Notes
200
www.lemo.com
LEMO complete product range
B
K
T
•
Unipole
Multipole
S
•
•
E
F
00
01
0A
3T
4A 4M
3K.
1D
93C
Y
05
5G
2G
2C
L
H
M
R
N
03
V
W
T7
P
SP
D
K/S 01 DIN
•
•
•
•
Coaxial 50 Ω
Coaxial 75 Ω
Multi Coaxial
Mixed Coax + LV
Triaxial 50 Ω
Triaxial 75 Ω
Mixed Triax + LV
Quadrax
High Voltage
Multi High Voltage
Mixed HV + LV
Fibre Optic
Multi Fibre Optic
Mixed FO + LV
Thermocouple
Fluidic
Multi Fluidic
Mixed Fluidic + LV
• included in this catalogue
Most frequently used in darker colour
B Series Keyed
S Series
K Series Keyed
T Series
E Series
F Series Keyed
00 Series
01 Series
0A Series
3T Series
4A Series
4M Series Keyed
3K.93C Series Keyed
1D Series
Y Series
05 Series
5G Series Keyed
2G Series Keyed
2C Series
L Series Keyed
H Series
M Series Keyed
R Series Keyed
N Series Keyed
03 Series Keyed
V Series
W Series Keyed
Cable assembly
REDEL D Series
01 Series Keyed
VAA Series
TAA Series
REDEL T7 Series
REDEL P Series Keyed REDEL SP Series Keyed
No reproduction or use without express permission of editorial or pictorial content, in any manner.
LEMO SA reserves the right to modify and improve specifications, at all times, without any notification.
LEMO HEADQUARTERS
SWITZERLAND
LEMO SA
Chemin des Champs-Courbes 28 - P.O. Box 194 - CH-1024 Ecublens
Tel. +41 21 695 16 00 - e-mail: info@lemo.com
SUBSIDIARIES
AUSTRIA
LEMO Elektronik GesmbH
Lemböckgasse 49/E6-3
1230 Wien
Tel: +43 1 914 23 20 0
Fax:+43 1 914 23 20 11
salesAT@lemo.com
BRAZIL
LEMO Latin America Ltda
Av. Dr. Adhemar de Barros,
566 – Sala 1407, Vila Adyana
CEP: 12245-011
São José dos Campos - SP - Brazil
Tel: +55 11 94242 4293
info-la@lemo.com
CANADA
LEMO Canada Inc
44 East Beaver Creek Road, unit 20
Richmond Hill, Ontario L4B 1G8
Tel: +1 905 889 56 78
Fax: +1 905 889 49 70
info-canada@lemo.com
CHINA / HONG KONG
LEMO Electronics (Shanghai) Co., Ltd
First Floor, Block E,
18 Jindian Road, Pudong
Shanghai, China, 201206
Tel: +86 21 5899 7721
Fax: +86 21 5899 7727
cn.sales@lemo.com
DENMARK
LEMO Denmark A/S
Mandal Allé 16A
5500 Middelfart
Tel: +45 45 20 44 00
Fax: +45 45 20 44 01
info-dk@lemo.com
FRANCE
LEMO France Sàrl
24/28 Avenue Graham Bell
Bâtiment Balthus 4
Bussy Saint Georges
77607 Marne la Vallée Cedex 3
Tel: +33 1 60 94 60 94
Fax: +33 1 60 94 60 90
info-fr@lemo.com
GERMANY
LEMO Elektronik GmbH
Hanns-Schwindt-Str. 6
81829 München
Tel: +49 89 42 77 03
Fax: +49 89 420 21 92
info@lemo.de
HUNGARY
REDEL Elektronika Kft
Nagysándor József u. 6-12
1201 Budapest
Tel: +36 1 421 47 10
Fax: +36 1 421 47 57
info-hu@lemo.com
ITALY
LEMO Italia srl
Viale Lunigiana 25
20125 Milano
Tel: +39 02 66 71 10 46
Fax: +39 02 37 90 80 46
sales.it@lemo.com
JAPAN
LEMO Japan Ltd
2-7-22, Mita,
Minato-ku, Tokyo, 108-0073
Tel: +81 3 54 46 55 10
Fax: +81 3 54 46 55 11
info-jp@lemo.com
LEMO
NETHERLANDS / BELGIUM
LEMO Connectors Nederland B.V.
Jacques Meuwissenweg 6
2031 AD Haarlem
Tel. +31 23 206 07 01
info-nl@lemo.com
NORWAY / ICELAND
LEMO Norway A/S
Soerumsandvegen 69,
1920 Soerumsand
Tel: +47 22 91 70 40
Fax: +47 22 91 70 41
info-no@lemo.com
SINGAPORE
LEMO Asia Pte Ltd
4 Leng Kee Road,
#06-09 SiS Building
Singapore 159088
Tel: +65 6476 0672
Fax: +65 6474 0672
sg.sales@lemo.com
SPAIN / PORTUGAL
IBERLEMO SAU
Brasil, 45, 08402 Granollers
Barcelona
Tel: +34 93 860 44 20
Fax: +34 93 879 10 77
info-es@lemo.com
SWEDEN / FINLAND
LEMO Nordic AB
Gunnebogatan 30
163 53 Spånga
Tel: +46 8 635 60 60
Fax: +46 8 635 60 61
info-se@lemo.com
SWITZERLAND
LEMO Verkauf AG
Grundstrasse 22 B,
6343 Rotkreuz
Tel: +41 41 790 49 40
ch.sales@lemo.com
TAIWAN
TAOYUAN TAIWAN
Tel: +886 967 132 824
speng@lemo.com
UNITED ARAB EMIRATES
LEMO Middle East Connectors LLC
Concorde Tower 11th Floor,
Office 1102, Dubai Media City,
P.O. Box 449849
Dubai, United Arab Emirates
Tel: +971 4 568 1904
info-me@lemo.com
UNITED KINGDOM
LEMO UK Ltd
12-20 North Street, Worthing,
West Sussex, BN11 1DU
Tel: +44 1903 23 45 43
lemouk@lemo.com
USA
LEMO USA Inc
P.O. Box 2408
Rohnert Park, CA 94927-2408
Tel: +1 707 578 88 11
+1 800 444 53 66
Fax: +1 707 578 08 69
info-US@lemo.com
DISTRIBUTORS
ARGENTINA, AUSTRALIA, BRAZIL, CHILE, COLOMBIA, CZECH REPUBLIC,
GREECE, INDIA, ISRAEL, NEW ZEALAND, PERU, POLAND, SOUTH AFRICA,
SOUTH KOREA, TURKEY, UKRAINE
www.lemo.com
CAT.UM.LEN.P1217, © LEMO / Data subject to change, printed in Switzerland, pdf updated November 2022
LEMO
工商网监
湘ICP备2023018690号
