PE7/PE8 Series
Specifications:
POWER ENTRY MODULES
Combination
Rated Voltage: 250VAC Maximum - 50/60 Hz
Rated Current:
115VAC
250VAC
3A
3A
6A
6A
Current Overload: 6X for 8 Seconds
Hi-Pot Test (1 min):
Line to Ground
1500VAC
Line to Line
1768VDC
Insulation Resistance: 9 x 109 Ω at 100VDC
Ambient Temperature: 40°C Max. at Rated Current
Humidity Range: 0% to 95% R.H.
Termination:
• IEC Receptacle
• Wire Wrap/Solder
Maximum Leakage Current:
Each Line to Ground
PE7, PE 8
115VAC, 60Hz:
0.25mA
250VAC, 50Hz:
0.40mA
Voltage Select Card: Installed in 120VAC position
unless otherwise specified
Agency Approvals:
Refer to Page 55 for Ordering Instructions
Features:
• RFI Filter Module Combines IEC Connector, Fusing,
and Voltage Select Features in One Unit
• PE7 Series Filters Provide 20% More Differential Mode
Attenuation Than Comparable Units
• Accepts Either U.S. or European Standard Fuse Sizes
PE7 Series Simplified Schematic
FUSING
LINE
G
L
SERIES-SERIES
110-220240 V
VOLTAGE
SELECTOR
1-POLE
B
A
a
b
G
FOR TRANSFORMERS WITH TAP
LOAD
C
A
C
240V
220V
c
D
D
N
Voltage Contacts
110V
b,e
220V
b,c
240V
a
d
H
F
E
e
2-POLE
E
F
2a
110V
G
52
MINIMUM INSERTION LOSS - dB (50 ohm Circuit)
Nominal
Current
Rating
Part
Number
3A
PE7XXX03
PE8XXX03
IEC/Solder
Tabs
6A
PE7XXX06
PE8XXX06
IEC/Solder
Tabs
www.curtisind.com
Termination
Line/Load
MODE
Frequency - MHz
1.0
5.0
.15
.50
Common
Differential
18
8
24
18
30
24
Common
Differential
10
8
19
18
24
24
Curtis Industries
A Division of Powers Holdings, Inc.
10
30
45
46
45
50
50
40
39
39
44
40
50
40
Specifications subject to change.
Dimensions are shown for
reference purposes only.
PE7 Series Simplified Schematic
FUSING
LINE
1-POLE
G
L
SERIES-PARALLEL
100-120220-240 V
VOLTAGE
SELECTOR
B
A
a
b
G
FOR TRANSFORMERS WITH TWO SEPARATE
WINDINGS
LOAD
120V
A
C
C
100V
c
D
D
d
H
N
e
F
Voltage Contacts
100V
a,c,e
120V
b,c,e
220V
a,d
240V
b,d
120V
E
E
F
2-POLE
G
B
a
b
G
B
A
C
A
C
115V
c
D
D
d
H
N
F
e
Voltage Contacts
115V
a,b d,e
230V
c
115V
E
E
F
2-POLE
Combination
G
L
G
LINE
ROCKER
SWITCH
FUSING
1-POLE
G
L
1-POLE
1
1a
LOAD
L
G
H
N
2-POLE
2
2a
POWER ENTRY MODULES
PE8 Series Simplified Schematic
N
2-POLE
G
Dimensions are in inches and millimeters
unless otherwise specified.
Values in parentheses are metric equivalents.
Curtis Industries
A Division of Powers Holdings, Inc.
1-800-657-0853
53
PE7/PE8 Series (continued)
PE7/PE8
Snap-Mount Series
(3 and 6Amp) Dimensions
Refer to Page 55
for Standard
Mounting Cutouts
2.266
(57,55)
1.260
(32,0)
1.051
(26,70)
.22
(5,5)
POWER ENTRY MODULES
Combination
2.283
(58,0)
.100
(2,7) Q.C. Terminals All Locations
LINE
LOAD
1.091
(27,71)
PE7/PE8
Screw-Mount Series
(3 and 6Amp) Dimensions
Refer to Page 55
for Standard
Mounting Cutouts
1.969
(50,0)
2.266
(57,55)
1.575
(40,0)
.22
(5,5)
1.051
(26,70)
1.142
(29,0)
2.283
(58,0)
LINE
54
www.curtisind.com
.126
(3,20)
Dia. Holes
LOAD
.100
(2,7) Terminals Except Switch
Curtis Industries
A Division of Powers Holdings, Inc.
1.091
(27,71)
Specifications subject to change.
Dimensions are shown for
reference purposes only.
How to Order
PE7
PE8
X
X
X
X
X
SERIES
PE = Power Entry
CURRENT RATING
3 = 3 AMP
6 = 6 AMP
OPTIONS
(Consult Factory)
0 = Standard Units
SWITCH
0 = No Switch
1 = SPST Rocker Switch
w/Q.C.
2 = DPST Rocker Switch
w/Q.C.
VOLTAGE SELECTOR
0 = No Selector (PE80 Series)
1 = 110-220-240 VAC
2 = 100-120-220-240 VAC
3 = 115-230 VAC
1.10
(27,9)
2.20
(55,9)
1.575
(40,0)
1.122
(28,50)
Cutout
.031" - .079" use 2.20"
.080" - .125" use 2.22"
Dimensions are in inches and millimeters
unless otherwise specified.
Values in parentheses are metric equivalents.
POWER ENTRY MODULES
.08 R
(2,0)
*See Below
1.122
(28,50)
*Panel Thickness
PE7/PE8
To change fuse, remove power cord
and open the front cover on the module.
Remove fuse holder and replace fuse.
Reinsert fuse holder and close cover.
To change the operating voltage on the
PE7 Series, remove the power cord and
open front cover. Rotate voltage select
wheel until desired voltage appears in
window of cover.
• Filter shipped without fuse.
Always use caution when selecting
and changing fuses and voltage
requirements. Curtis Industries is not
responsible for malfunction due to
improper installation/selection of fuse
and/or voltage select.
PE7/PE8 Screw Mount Series
PE7/PE8 Snap-Mount Series
2.20
(55,9)
INSTALLATION INSTRUCTION
IMPORTANT – CHANGING
FUSE/VOLTAGE
Combination
MOUNTING
METHOD & FUSING
0 = Snap Mount Metric Fuse
1 = Snap Mount U.S. Fuse
2 = Snap Mount 2 Metric Fuse
3 = Snap Mount 2 U.S. Fuses
6 = Screw Mount Metric Fuse
7 = Screw Mount U.S. Fuse
8 = Screw Mount 2 Metric Fuses
9 = Screw Mount 2 U.S. Fuses
4-40
(M3)
.08 R
(2,0)
Curtis Industries
A Division of Powers Holdings, Inc.
1-800-657-0853
55
