SMB7H-J-P-HN-RA-TH1

REVISION E SMB7H-J-P-XX-RA-TH1 DESIGNED & DIMENSIONED IN MILLIMETERS[INCHES] TERMINATION -TH1: THROUGH HOLE ORIENTATION -RA: RIGHT ANGLE PLATING -HN: HEAVY GOLD/NICKEL (SEE NOTE 6 & 7) (SMB7H-J-P-H-RA-TH1-PIN) (SMB7H-J-P-F-RA-TH1-SHL) (SMB7H-J-P-N-RA-TH1-BDY) GENDER -J: JACK TYPE -P: PCB E 3.45±0.05 .136±.002 TO INSULATOR 0.98±0.20 .039±.008 -H: HEAVY GOLD (SEE NOTE 6 & 7) (SMB7H-J-P-H-RA-TH1-PIN) (SMB7H-J-P-F-RA-TH1-SHL) (SMB7H-J-P-F-RA-TH1-BDY) INSULATOR 1 (SMB7H-J-P-RA-TH1-INS1) SHELL (SMB7H-J-P-X-RA-TH1-SHL) "A" 0.51 .020 REF 8.50 .335 (REF) BODY (SMB7H-J-P-X-RA-TH1-BDY) 11.00 .433 (REF) SMB7H-J-P-H-RA-TH1 (SHOWN) 5.00 .197 'B' 2.50 .098 (REF) "A" 0.96 .038 REF INSULATOR 1 (SMB7H-J-P-RA-TH1-INS2) SECTION "A"-"A" PIN (SMB7H-J-P-X-RA-TH1-PIN) 5.08 .200 (REF) 7.00 .276 (REF) 5.08 .200 (REF) RECOMMENDED MOUNTING HOLE NOTES: DETAIL 'B' SCALE 16 : 1 FLUSH 0.10 1. REPRESENTS A CRITICAL DIMENSION. 2. PUSHOUT FORCE FOR INSULATOR: 35.58 N [8.0 LB] MIN. 3. PUSHOUT FORCE FOR CENTER CONTACT: 17.79 N [4.0 LB] MIN. 4. PRODUCT TO BE PACKAGED PER PACKAGING STANDARD CO-HD-WI-3040-M. 5. RoHs COMPLIANT. 6. COMPONENT PLATING DESIGNATIONS: -H: 0.00076[0.000030] (MIN) GOLD OVER 0.00127[0.000050] (MIN) NICKEL. -F: 0.00008[0.000003] (MIN) GOLD OVER 0.00127[0.000050] (MIN) NICKEL. -N: 0.00254[0.000100] (MIN) NICKEL. 7. ASSEMBLY PLATING DESIGNATIONS: -HN: (CENTER CONTACT)-H: (OUTER CONTACT)-F: (REMAINING METAL PARTS)-N: -H: (CENTER CONTACT)-H: (OUTER CONTACT)-F: (REMAINING METAL PARTS)-F: 1.60 .063 (4 PLC) 5.08 .200 14.10 .555 (REF) 1.20 .047 5.08 .200 F:\DWG\MISC\MKTG\SMB7H-J-P-XX-RA-TH1-MKT.SLDDRW UNLESS OTHERWISE SPECIFIED, DIMENSIONS ARE IN MILLIMETERS. TOLERANCES ARE: DECIMALS ANGLES .X: 0.3 [.01] 2 .XX: 0.13 [.005] .XXX: 0.051 [.0020] PROPRIETARY NOTE THIS DOCUMENT CONTAINS INFORMATION CONFIDENTIAL AND PROPRIETARY TO SAMTEC, INC. AND SHALL NOT BE REPRODUCED OR TRANSFERRED TO OTHER DOCUMENTS OR DISCLOSED TO OTHERS OR USED FOR ANY PURPOSE OTHER THAN THAT WHICH IT WAS OBTAINED WITHOUT THE EXPRESSED WRITTEN CONSENT OF SAMTEC, INC. DO NOT SCALE DRAWING MATERIAL: CONTACT, SHELL, BODY: BRASS DIELECTRIC: PFTE SHEET SCALE: 3:1 520 PARK EAST BLVD, NEW ALBANY, IN 47150 PHONE: 812-944-6733 FAX: 812-948-5047 e-Mail: info@SAMTEC.com code: 55322 DESCRIPTION: SMB7 RIGHT ANGLE JACK- 75 OHM DWG. NO. SMB7H-J-P-XX-RA-TH1 BY: G. HERMAN 03/25/2008 SHEET 1 OF 1