宁波中车时代传感技术有限公司 www.csrsensor.com
NACF.500C-S5/V 电流传感器 Current Transducer
版本:A
Applications
产 品 说 明
NACF.500C-S5/V 开环霍尔电流传感器适用于对交流、直流、脉冲电流的隔离精确测量,测量时一次
侧与二次侧间完全绝缘。
For the electronic measurement of currents: AC, DC,pulsed…,with galvanic separation between the
primary circuits and the secondary circuits.
产品优点 Advantages
体积小 Small size and space savings
产品应用领域 Applications
变频器 Static converters
不间断电源Uninterruptible Power
Supplies (UPS)
参照标准
Standards
EN 50178: 1997
IEC60950-1:2001
主要电气参数 Main electrical data
(@±IPN, RL = 10 kΩ, TA = 25℃)
额定测量电流 IPN
Primary nominal current
500A
测量范围 IPM
Primary current measuring range
±900A
电源电压 VC
Supply voltage
DC±15(1±5%)V
电流消耗 IC
Current consumption
≤±30mA
额定测量输出 VOUT
Output voltage
±4V
输出内阻 ROUT
Output internal resistance
100Ω
负载电阻 RL
Load resistance
≥10kΩ
精度 - 动态参数 Accuracy - Dynamic performance data
基本误差δi(IPN,TA=25℃)
Accuracy(excluding offset)
≤±1%of IPN
零点输出误差δZ(TA = 25℃)
Electrical offset voltage
≤±30mV
Temperature coefficient of δZt
≤±1mV/℃
Temperature coefficient of VOUT
≤±0.1%/℃
Step response time to 90 % of IPN
≤3µS
线性度δL(0 … ±IPN)
磁滞失调电压VOH(IP=0,1×IPN冲击后)
零点温度漂移δZt(TA = -40℃~+85℃)
满量程温度漂移
δFSt(TA =-40℃~+85℃)
响应时间
TR(90% of IPN&di/dt > 50 A/µS)
带宽(−3dB)BW
Linearity error
Hysteresis offset voltage
@ IP=0,after an excursion of 1×IPN
≤±1%of IPN
≤±35mV
Frequency bandwidth (−3dB)
DC … 25kHz
Ambient operating temperature
-40~+85℃
一般数据 General data
工作温度 Ta
宁波中车时代传感技术有限公司 www.csrsensor.com
储存温度 Ts
Ambient storage temperature
-45~+90℃
重量 m
Mass
≤80g
绝缘耐压 Insulation coordination
耐压
Voltage for AC insulation test, 50Hz,1min
3kV
绝缘电阻 RIS
Isolation resistance
≥1000MΩ
爬电距离
Creepage distance
7.08mm
电气间隙
Clearance
6.23mm
NACF.500C-S5/V 电压传感器外形图 Dimensions NACF.500C-S5/V Series (in mm)
电气连接 Connection
宁波中车时代传感技术有限公司 www.csrsensor.com
机械特征 Mechanical characteristics
备注 Remark
当测量电流方向与传感器上标示
的
方向一致时,传感器输出
VOUT 为正。
2. 产品二次侧连接线优选屏蔽线,屏
蔽层接近产品端连接线可接机壳,
负电源或电源 0V
3. 传感器安装螺钉孔的垂直度要求:
要求在国家标准 8 级或以上(或
0.06 以下)
。
4. 传感器接插件要求:接插件必须选
用厂家提供的配件,禁止使用其它
同型号类似配件。
传感器安装平面度要求:
(a) . 大平面安装平面度国家标准 11 级
或以上(或平面起伏小于 0.25mm)
;
(b). 安装面若有小圆凸台设计时平面
度要求达国家标准 12 级或以上(或平
面起伏小于 0.5mm)
。
1.
未注公差
General tolerance
±0.5mm
传感器安装
Transducer fastening
1 hole ø4.5mm
1 M4 steel screws
推荐力矩
Recommended fastening torque
0.75 N·m
穿心孔
Primary through-hole
20.4×10.4mm
次边电气连接
Connection of secondary
MOLEX 4芯连接器
很抱歉,暂时无法提供与“NACF.500C-S5/V”相匹配的价格&库存,您可以联系我们找货
免费人工找货