VL822-Q7

Data Sheet VL822 USB 3.1 Gen2 Hub Controller December 26th, 2018 Revision 0.90 VLI VL822-Q5 USB 3.1 Gen 2 2-Port Hub Controller QFN56 V VLI VL822-Q7 V VLI VL822-Q8 USB 3.1 Gen 2 4-Port Hub Controller USB 3.1 Gen 2 4-Port Hub Controller w/ USB-C™ Support QFN-76 QFN-88 VL822 USB 3.1 Gen2 Hub Controller Revision History Rev Date 0.90 12/26/2018 Note First Preliminary Release Initial EC -2- VL822 USB 3.1 Gen2 Hub Controller Contents Revision History ........................................................................................... 2 Contents ..................................................................................................... 3 List of Figures .............................................................................................. 3 Product Features .......................................................................................... 4 VL822 System Overview ............................................................................... 5 USB Battery Charging Behavior ..................................................................... 8 Pinout (VL822-Q7) ....................................................................................... 9 Pin List (VL822-Q7) ..................................................................................... 10 Pin Descriptions (VL822-Q7) ......................................................................... 11 Pinout (VL822-Q8) ...................................................................................... 14 Pin List (VL822-Q8) ..................................................................................... 15 Pin Descriptions (VL822-Q8) ......................................................................... 16 Pinout (VL822-Q5) ...................................................................................... 20 Pin List (VL822-Q5) ..................................................................................... 21 Pin Descriptions (VL822-Q5) ......................................................................... 22 Electrical Specification.................................................................................. 25 Timing Requirements for SPI Flash ................................................................ 26 General Reflow Profile Guidelines ................................................................... 27 Package Mechanical Specifications (VL822-Q7) ............................................... 28 Package Mechanical Specifications (VL822-Q8) ............................................... 29 Package Mechanical Specifications (VL822-Q5) ............................................... 30 Package Top Side Marking & Ordering Information ........................................... 31 List of Figures Figure 1 – VL822-Q7 Block Diagram ............................................................... 6 Figure 2 – VL822-Q8 Block Diagram ............................................................... 6 Figure 3 – VL822-Q5 Block Diagram ............................................................... 7 Figure 4 – VL822-Q7 Pin Diagram .................................................................. 9 Figure 5 – VL822-Q8 Pin Diagram.................................................................. 14 Figure 6 – VL822-Q5 Pin Diagram.................................................................. 20 Figure 7 – SPI Timing .................................................................................. 26 Figure 8 – Reflow ........................................................................................ 27 Figure 9 – Mechanical Specification – Q7 (QFN 76L 9x9x0.85 mm) Package ........ 28 Figure 10 – Mechanical Specification – Q8 (QFN 88L 10x10x0.85 mm) Package .. 29 Figure 11 – Mechanical Specification – Q5 (QFN 56L 7x7x0.85 mm) Package ...... 30 Figure 12 –Package Top Side Marking ............................................................ 31 -3- VL822 USB 3.1 Gen2 Hub Controller Product Features VL822-Q8 / VL822-Q7 / VL822-Q5 USB 3.1 Gen2 SuperSpeed Plus 4/2-Port USB Hub Controller  USB 3.1 Compliant – Compliant to Universal Serial Bus 3.1 Specification – SuperSpeed Plus USB (USB 3.1 Gen2) – Compliant to Universal Serial Bus 2.0 Specification – USB 2.0 Hub Supports MTT – Supports Simultaneous Operation of Any Combination of SuperSpeed Plus, SuperSpeed, High-Speed, Full-Speed, and Low-Speed Devices – Supports USB Power Saving Features such as Link Power Management, Ux States, Selective Suspend, and Function Suspend – In-house USB PHY employs advanced CMOS process for low power consumption  USB Type-C 1.0 Rev 1.2 Compliant – Compliant to USB Type-C Specification Rev 1.3 – VL822-Q8: Integrated 10Gbps Mux for UFP and 2x DFP – Requires External CC Logic Controller for Orientation Detection/Vconn (Such as VP246 or VP225) – Additional USB-C DFP support requires separate CC Logic and Mux  Integrated USB Devices – USB Billboard Class 1.21 Device Implemented as a USB 2.0 Virtual Device Configurable Behavior – Expose When Necessary / Always Present / Disabled – USB HID Class Device Implemented as a USB 2.0 Virtual Device, Facilitates FW Update or Media Control Buttons Configurable Behavior – Always Present / Disabled  Full Sideband Signal Support – Supports Any Combination of Individual or Ganged Mode Over-Current for All Ports – Supports PWM LED Status Lights – SPI Interface for Firmware. – Firmware Upgradable over USB  Comprehensive USB Battery Charging Support – Supports USB Battery Charging Specification v1.2 (SDP, CDP, DCP) – Support for Vendor Specific Charging Modes eg. Apple 2.4A, Samsung, etc. – Supports YD/T 1591-2009 – Supports Stand-Alone Charging when System is Suspend, Shut Down, or Disconnected – Any Combination of DFPs can be Configured to Support USB Battery Charging  Power and Package – Requires 3.3V and 1.05V Inputs – VL822-Q8: QFN 88L green package (10x10x0.85 mm) – VL822-Q7: QFN 76L green package (9x9x0.85 mm) – VL822-Q5: QFN 56L green package (7x7x0.85 mm) – Pin Compatibility with VL820 – 25MHz Xtal -4- VL822 USB 3.1 Gen2 Hub Controller VL822 System Overview VIA Lab’s VL822 is USB 3.1 Gen2 Hub Controller and it features highly integrated, application specific design. VL822 features 1x upstream port and 4x/2x downstream ports, all of which support 10Gbps USB 3.1 Gen2 operation. The downstream ports can support any combination of SuperSpeed Plus (10Gbps), SuperSpeed (5Gbps), High Speed (480Mbps), Full Speed (12Mbps), and Low Speed (1.5Mbps) devices. VL822’s integrated USB 2.0 hub features Multiple Transaction Translators, providing increased bandwidth and performance when multiple Full Speed devices are simultaneously used. VL822 comes in three variants: VL822-Q8 utilizes the QFN88 10x10x0.85 mm package while the VL822-Q7 utilizes the smaller QFN76 9x9x0.85mm package and VL822-Q5 utilizes the smaller QFN56 7x7x0.85mm package for two port configure. The larger QFN88 variant features integrated 10Gbps Muxes for the Upstream Facing Port and two Downstream Facings Ports whereas the smaller QFN76/QFN56 variant does not. The integrated 10Gbps Muxes are ideal for Data-Only USB-C applications that would otherwise require an external Mux, with the advantage of potential board area savings and improved signal integrity. If additional USB-C Ports are need, separate CC Logic and Mux solutions. VL822 features an optionally configurable USB Billboard Device when used in USB-PD Alternate Mode applications, and an optionally configurable USB HID endpoint to support Media Control Buttons such as Play/Pause, Volume Up/Down, etc. VL822 features flexible firmware architecture, providing a framework for custom functions in addition to in-field updates. Various parameters including USB configuration, Tx equalization setting, and GPIO behavior are changeable via firmware. VL822 also features an optionally configurable USB Charging Controller for charging various devices such as smartphones and tablets that can be configure on a per-port basis. VL822-based hub devices work under Windows, Mac OS X, and various Linux kernels without additional drivers. VL822-based hub devices are also compatible with non-x86 devices and platforms that support USB hub functions such as smart phones, tablets, and set-top boxes. It is well suited for all USB hub applications such as standalone USB hubs, Notebook/Ultrabook docking stations/port-replicators, desktop PC front panel, motherboard on-board hub, and USB hub compound devices. -5- VL822 USB 3.1 Gen2 Hub Controller Figure 1 – VL822-Q7 Block Diagram Figure 2 – VL822-Q8 Block Diagram -6- VL822 USB 3.1 Gen2 Hub Controller Figure 3 – VL822-Q5 Block Diagram -7- VL822 USB 3.1 Gen2 Hub Controller USB Battery Charging Behavior 3 Concepts of Rapid Charging over USB:  Rapid Charging over USB enables charging of devices at rates in excess of baseline USB standards. The current limit of USB 2.0 is 500mA for configured devices, and the current limit of USB 3.0 is 900mA for configured devices. Depending on the device, Rapid Charging implementations typically feature current limits between 1000mA to 2400mA.  It is the Host/Hub’s responsibility to advertise Rapid Charging capabilities, and it is the Device’s responsibility to recognize and determine those capabilities. Rapid Charging over USB enables charging at rates in excess of baseline USB specifications, so in order to prevent a situation where a device sinks more current than what a port is rated for, different manufacturers employ various charging schemes in an attempt to ensure safe and reliable operation with their respective device and charger. It goes without saying that Rapid Charging will only occur when both Host/Hub and Device supports it.  The rate at which a device charges is dependent upon the device. This means that the device must determine the host/hub port’s capabilities to determine which charging mode to use. Also, the rate at which a device charges can vary depending on the status of the device. For example, some devices only charge at their maximum rate when the battery is nearly depleted. When the battery is nearly full, they may switch to a tricklecharge mode. The Host/Hub rapid-charging port has no control over this behavior. Supported USB Charging Modes SDP – Standard Downstream Port This is a typical USB 2.0 or USB 3.0 port and does not explicitly support Rapid USB Charging. SDP is constrained to the current limits as defined in the USB 2.0 or USB 3.0 spec which are 500mA and 900mA respectively. While the actual current limit is enforced by the polyfuse or power-switch providing current-limiting functionality for the downstream port, most USB devices will not draw more than 500mA or 900mA under USB 2.0 or USB 3.0 modes. CDP – Charging Downstream Port CDP is defined in the USB Battery Charging Specification 1.2 and enables devices that are able to correctly recognize CDP to simultaneously function as a USB device while drawing up to 1.5A for Rapid Charging when connected to the downstream port of a USB Host or Hub that advertises CDP capability. DCP – Dedicated Charging Port DCP is defined in the USB Battery Charging Specification 1.2 and has been in use on an unofficial basis prior to the official USB Battery Charging Specification. DCP is a dedicated charging mode, so when a device is charging under DCP, regular USB operations such as data transfer to the device are not supported. Special Modes Various vendors such as Apple, RIM, Motorola, etc. may employ different detection mechanisms compared to other USB devices and thus, may enter Rapid Charging under the previously mentioned charging modes. VL822 supports an auto detection mechanism that provides charging for the majority of devices. -8- VL822 USB 3.1 Gen2 Hub Controller Pinout (VL822-Q7) Figure 4 – VL822-Q7 Pin Diagram -9- VL822 USB 3.1 Gen2 Hub Controller Pin List (VL822-Q7) Table 1 – VL822-Q7 Pin List Pin Pin Name Pin Pin Name 1 USBOC1 39 USBPE4 2 USBPE1 40 USBOC4 3 SSTX1+ 41 USBOC0 4 SSTX1– 42 USBPE0 5 VCC10I 43 VBUSDET0 6 SSRX1+ 44 USB3XO 7 SSRX1– 45 USB3XI 8 VCC10I 46 VCC33I 9 HSD1+ 47 REXT 10 HSD1– 48 VDD 11 VDD 49 SSTX0– 12 SSTX2+ 50 SSTX0+ 13 SSTX2– 51 VCC10I 14 VCC10I 52 SSRX0– 15 SSRX2+ 53 SSRX0+ 16 SSRX2– 54 VCC10I 17 VCC33I 55 HSD0+ 18 HSD2+ 56 HSD0– 19 HSD2– 57 GPIO0/HID0 20 USBOC3 58 GPIO1/HID1 21 USBPE3 59 GPIO2/HID2 22 HSD3+ 60 GPIO3/HID3 23 HSD3– 61 GPIO4/HID4 24 VCC33I 62 VCC33I 25 SSTX3+ 63 GPIO5/EXTPWRON/WAKE 26 SSTX3– 64 GPIO6 / USBSUS 27 VCC10I 65 GPIO7 / SMDAT 28 SSRX3+ 66 GPIO8 / SMCLK 29 SSRX3– 67 VDD 30 VDD 68 RESET# 31 SSTX4+ 69 USBLED1 / SPISI 32 SSTX4– 70 USBLED2 / SPICK 33 VCC10I 71 USBLED3 / SPISO 34 SSRX4+ 72 USBLED4 / SPICS 35 SSRX4– 73 VCC33I 36 VCC10I 74 TESTEN 37 HSD4+ 75 USBOC2 38 HSD4– 76 USBPE2 - 10 - VL822 USB 3.1 Gen2 Hub Controller Pin Descriptions (VL822-Q7) Signal Type Definition Name Type Signal Description Input I A logic input-only signal Output O A logic output only signal Input/ Output I/O A logic bi-directional signal Power PWR A power pin Ground GND A ground pin USB 3.1 Interface Pin Name Pin # I/O Signal Description SSTX0- 49 O USB 3.1 UFP Differential TX– SSTX0+ 50 O USB 3.1 UFP Differential TX+ SSRX0- 52 I USB 3.1 UFP Differential RX– SSRX0+ 53 I USB 3.1 UFP Differential RX+ SSTX1+ 3 O USB 3.1 DFP1 Differential TX+ SSTX1- 4 O USB 3.1 DFP1 Differential TX– SSRX1+ 6 I USB 3.1 DFP1 Differential RX+ SSRX1- 7 I USB 3.1 DFP1 Differential RX– SSTX2+ 12 O USB 3.1 DFP2 Differential TX+ SSTX2- 13 O USB 3.1 DFP2 Differential TX– SSRX2+ 15 I USB 3.1 DFP2 Differential RX+ SSRX2- 16 I USB 3.1 DFP2 Differential RX– SSTX3+ 25 O USB 3.1 DFP3 Differential TX+ SSTX3- 26 O USB 3.1 DFP3 Differential TX– SSRX3+ 28 I USB 3.1 DFP3 Differential RX+ SSRX3- 29 I USB 3.1 DFP3 Differential RX– SSTX4+ 31 O USB 3.1 DFP4 Differential TX+ SSTX4- 32 O USB 3.1 DFP4 Differential TX– SSRX4+ 34 I USB 3.1 DFP4 Differential RX+ SSRX4- 35 I USB 3.1 DFP4 Differential RX– Analog Command Block Pin Name Pin # I/O Signal Description USB3XO 44 O 25M Crystal Output USB3XI 45 I 25M Crystal Input REXT 47 I Connect to External Reference Resistor (12.4K+/- 1%) - 11 - VL822 USB 3.1 Gen2 Hub Controller Test Pin Pin Name Pin # I/O TESTEN 74 I GPIO7 / SMDAT 65 I/O GPIO8 / SMCLK 66 I/O Signal Description Test Mode Enable Low: Normal mode. High: Test mode. Available for GPIO Use, Config via Firmware Setting. SMBus data with Proprietary Data Format. (Open Drain) Available for GPIO Use, Config via Firmware Setting. SMBus clock with Proprietary Data Format. (Open Drain) USB 2.0 Interface Pin Name Pin # I/O Signal Description HSD0+ 55 I/O USB 2.0 UFP Differential D+ HSD0– 56 I/O USB 2.0 UFP Differential D– HSD1+ 9 I/O USB 2.0 DFP1 Differential D+ HSD1– 10 I/O USB 2.0 DFP1 Differential D– HSD2+ 18 I/O USB 2.0 DFP2 Differential D+ HSD2– 19 I/O USB 2.0 DFP2 Differential D– HSD3+ 22 I/O USB 2.0 DFP3 Differential D+ HSD3– 23 I/O USB 2.0 DFP3 Differential D– HSD4+ 37 I/O USB 2.0 DFP4 Differential D+ HSD4– 38 I/O USB 2.0 DFP4 Differential D– Power and Ground Pin Name Pin # I/O Signal Description GND EPAD GND Ground VDD 11, 30, 48, 67 PWR 1.05V Core Power PWR 1.05V Analog Power PWR 3.3V Analog Power VCC10I VCC33I 5, 8, 14, 27, 33, 36, 51, 54 17, 24, 46, 62, 73 Side Band Signal and Miscellaneous Pin Name Pin # I/O USBOC0 41 I or I/O USBPE0 42 O USBOC1 1 I or I/O USBPE1 2 O Signal Description UFP Over Current Detection Open Drain (3.3V Max); Pin must be pulled high if NC. High: Normal Low: Port Over Current Event UFP USB PE USB Power Enable Mode High: Enable Low: Off DFP1 Over Current Detection Open Drain (3.3V Max); Pin must be pulled high if NC. High: Normal Low: Port Over Current Event DFP1 USB PE USB Power Enable Mode High: Enable Low: Off - 12 - VL822 USB 3.1 Gen2 Hub Controller Side Band Signal and Miscellaneous Pin Name Pin # I/O USBOC2 75 I or I/O USBPE2 76 O USBOC3 20 I or I/O USBPE3 21 O USBPE4 39 I or I/O USBOC4 40 O GPIO0 / HID0 57 I/O GPIO1 / HID1 58 I/O GPIO2 / HID2 59 I/O GPIO3 / HID3 60 I/O GPIO4 / HID4 61 I/O GPIO5 / EXTPWRON / WAKE 63 I/O GPIO6 / USBSUS 64 I/O RESET# 68 I USBLED1 / SPISI 69 I/O USBLED2 / SPICLK 70 I/O USBLED3 / SPISO 71 I/O USBLED4 / SPICS 72 I/O VBUSDET0 43 I Signal Description DFP2 Over Current Detection Open Drain (3.3V Max); Pin must be pulled high if NC. High: Normal Low: Port Over Current Event DFP2 USB PE USB Power Enable Mode High: Enable Low: Off DFP3 Over Current Detection Open Drain (3.3V Max); Pin must be pulled high if NC. High: Normal Low: Port Over Current Event DFP3 USB PE USB Power Enable Mode High: Enable Low: Off DFP4 USB PE USB Power Enable Mode High: Enable Low: Off DFP4 Over Current Detection Open Drain (3.3V Max); Pin must be pulled high if NC. High: Normal Low: Port Over Current Event GPIO / HID Shared Pin. Available for GPIO Use, Config via Firmware Setting. Available for HID button Use, Config via Firmware Setting. GPIO / HID Shared Pin. Available for GPIO Use, Config via Firmware Setting. Available for HID button Use, Config via Firmware Setting. GPIO / HID Shared Pin. Available for GPIO Use, Config via Firmware Setting. Available for HID button Use, Config via Firmware Setting. GPIO / HID Shared Pin. Available for GPIO Use, Config via Firmware Setting. Available for HID button Use, Config via Firmware Setting. GPIO / HID Shared Pin. Available for GPIO Use, Config via Firmware Setting. Available for HID button Use, Config via Firmware Setting. GPIO / External Power Status / Wake Shared pin. Available for GPIO Use, Config via Firmware Setting. DC Jack Power Source Insert Detection (3.3V Max) Available for Connected Standby use, Config via Firmware Setting. GPIO Available for GPIO Use, Config via Firmware Setting. Reset Input of Hub Controller Low: Reset High: Normal Operation Power On sequence, Refer to Appendix-1. DFP1 LED Indicator / SPISI shared pin. Active High Output for LED Use. DFP2 LED Indicator / SPISCLK shared pin. Active High Output for LED Use. DFP3 LED Indicator / SPISO shared pin. Active High Output for LED Use. DFP4 LED Indicator / SPICS shared pin. Active High Output for LED Use UFP Vbus Detection (3.3V Max) - 13 - VL822 USB 3.1 Gen2 Hub Controller Pinout (VL822-Q8) Figure 5 – VL822-Q8 Pin Diagram - 14 - VL822 USB 3.1 Gen2 Hub Controller Pin List (VL822-Q8) Table 2 – VL822-Q8 Pin List Pin Pin Name Pin Pin Name 1 SSTX1A+ 45 USBPE4 2 SSTX1A– 46 USBOC4 3 SSTX1B– 47 USBOC0 4 SSTX1B+ 48 USBPE0 5 VCC10I 49 VBUSDET0 6 SSRX1A+ 50 USB3XO 7 SSRX1A– 51 USB3XI 8 SSRX1B– 52 VCC33I 9 SSRX1B+ 53 REXT 10 VCC10I 54 VDD 11 HSD1+ 55 SSTX0A+ 12 HSD1– 56 SSTX0A– 13 VDD 57 SSTX0B– 14 SSTX2+ 58 SSTX0B+ 15 SSTX2– 59 VCC10I 16 VCC10I 60 SSRX0A+ 17 SSRX2+ 61 SSRX0A– 18 SSRX2– 62 SSRX0B– 19 VCC33I 63 SSRX0B+ 20 HSD2+ 64 VCC10I 21 HSD2– 65 HSD0+ 22 USBOC3 66 HSD0– 23 USBPE3 67 GPIO0/HID0/ATT0 24 HSD3+ 68 GPIO1/HID1/ORI0 25 HSD3– 69 GPIO2/HID2/ATT1 26 VCC33I 70 GPIO3/HID3/ORI1 27 SSTX3+ 71 GPIO4/HID4/ATT4 28 SSTX3– 72 VCC33I 29 VCC10I 73 GPIO5/EXTPWRON/WAKE/ORI4 30 SSRX3+ 74 GPIO6 31 SSRX3– 75 GPIO7 / SMDAT 32 VDD 76 GPIO8 / SMCLK 33 SSTX4A+ 77 VDD 34 SSTX4A– 78 RESET# 35 SSTX4B– 79 USBLED1 / SPISI 36 SSTX4B+ 80 USBLED2 / SPICK 37 VCC10I 81 USBLED3 / SPISO 38 SSRX4A+ 82 USBLED4 / SPICS 39 SSRX4A– 83 VCC33I 40 SSRX4B– 84 TESTEN 41 SSRX4B+ 85 USBOC2 42 VCC10I 86 USBPE2 43 HSD4+ 87 USBOC1 44 HSD4– 88 USBPE1 - 15 - VL822 USB 3.1 Gen2 Hub Controller Pin Descriptions (VL822-Q8) Signal Type Definition Name Type Signal Description Input I A logic input-only signal Output O A logic output only signal Input/ Output I/O A logic bi-directional signal Power PWR A power pin Ground GND A ground pin Pin Name Pin # I/O Signal Description SSTX0A+ 55 O USB 3.1 UFP Differential TX+; Side A SSTX0A- 56 O USB 3.1 UFP Differential TX–; Side A SSTX0B- 57 O USB 3.1 UFP Differential TX–; Side B SSTX0B+ 58 O USB 3.1 UFP Differential TX+; Side B SSRX0A+ 60 I USB 3.1 UFP Differential RX+; Side A SSRX0A- 61 I USB 3.1 UFP Differential RX–; Side A SSRX0B- 62 I USB 3.1 UFP Differential RX–; Side B SSRX0B+ 63 I USB 3.1 UFP Differential RX+; Side B SSTX1A+ 1 O USB 3.1 DFP1 Differential TX+; Side A SSTX1A- 2 O USB 3.1 DFP1 Differential TX–; Side A SSTX1B- 3 O USB 3.1 DFP1 Differential TX–; Side B SSTX1B+ 4 O USB 3.1 DFP1 Differential TX+; Side B SSRX1A+ 6 I USB 3.1 DFP1 Differential RX+; Side A SSRX1A- 7 I USB 3.1 DFP1 Differential RX–; Side A SSRX1B- 8 I USB 3.1 DFP1 Differential RX–; Side B SSRX1B+ 9 I USB 3.1 DFP1 Differential RX+; Side B SSTX2+ 14 O USB 3.1 DFP2 Differential TX+ SSTX2- 15 O USB 3.1 DFP2 Differential TX– SSRX2+ 17 I USB 3.1 DFP2 Differential RX+ SSRX2- 18 I USB 3.1 DFP2 Differential RX– SSTX3+ 27 O USB 3.1 DFP3 Differential TX+ SSTX3- 28 O USB 3.1 DFP3 Differential TX– SSRX3+ 30 I USB 3.1 DFP3 Differential RX+ SSRX3- 31 I USB 3.1 DFP3 Differential RX– SSTX4A+ 33 O USB 3.1 DFP4 Differential TX+; Side A SSTX4A- 34 O USB 3.1 DFP4 Differential TX–; Side A SSTX4B- 35 O USB 3.1 DFP4 Differential TX–; Side B SSTX4B+ 36 O USB 3.1 DFP4 Differential TX+; Side B SSRX4A+ 38 I USB 3.1 DFP4 Differential RX+; Side A SSRX4A- 39 I USB 3.1 DFP4 Differential RX–; Side A SSRX4B- 40 I USB 3.1 DFP4 Differential RX–; Side B SSRX4B+ 41 I USB 3.1 DFP4 Differential RX+; Side B USB 3.1 Interface - 16 - VL822 USB 3.1 Gen2 Hub Controller USB 2.0 Interface Pin Name Pin # I/O Signal Description HSD0+ 65 I/O USB 2.0 UFP Differential D+ HSD0– 66 I/O USB 2.0 UFP Differential D– HSD1+ 11 I/O USB 2.0 DFP1 Differential D+ HSD1– 12 I/O USB 2.0 DFP1 Differential D– HSD2+ 20 I/O USB 2.0 DFP2 Differential D+ HSD2– 21 I/O USB 2.0 DFP2 Differential D– HSD3+ 24 I/O USB 2.0 DFP3 Differential D+ HSD3– 25 I/O USB 2.0 DFP3 Differential D– HSD4+ 43 I/O USB 2.0 DFP4 Differential D+ HSD4– 44 I/O USB 2.0 DFP4 Differential D– Analog Command Block Pin Name Pin # I/O Signal Description USB3XO 50 O 25M Crystal Output USB3XI 51 I 25M Crystal Input REXT 53 I Connect to External Reference Resistor (12.4K+/- 1%) Pin Name Pin # I/O Signal Description GND EPAD GND Ground VDD 13,32,54, 77 5, 10, 16, 29, 37, 42, 59. 64, 19, 26, 52, 72, 83 PWR 1.05V Core Power PWR 1.05V Analog Power PWR 3.3V Analog Power Pin Name Pin # I/O TESTEN 84 I GPIO7 / SMDAT 75 I/O GPIO8 / SMCLK 76 I/O Signal Description Test Mode Enable Low: Normal mode. High: Test mode. Available for GPIO Use, Config via Firmware Setting. SMBus data with Proprietary Data Format. (Open Drain) Available for GPIO Use, Config via Firmware Setting. SMBus clock with Proprietary Data Format. (Open Drain) Power and Ground VCC10I VCC33I Test Pin - 17 - VL822 USB 3.1 Gen2 Hub Controller Side Band Signal and Miscellaneous Pin Name Pin # I/O USBOC0 47 I or I/O USBPE0 48 O USBOC1 87 I or I/O USBPE1 88 O USBOC2 85 I or I/O USBPE2 86 O USBOC3 22 I or I/O USBPE3 23 O USBPE4 45 I or I/O USBOC4 46 O Signal Description UFP Over Current Detection Open Drain (3.3V Max); Pin must High: Normal Low: Port Over Current Event UFP USB PE USB Power Enable Mode High: Enable Low: Off DFP1 Over Current Detection Open Drain (3.3V Max); Pin must High: Normal Low: Port Over Current Event DFP1 USB PE USB Power Enable Mode High: Enable Low: Off DFP2 Over Current Detection Open Drain (3.3V Max); Pin must High: Normal Low: Port Over Current Event DFP2 USB PE USB Power Enable Mode High: Enable Low: Off DFP3 Over Current Detection Open Drain (3.3V Max); Pin must High: Normal Low: Port Over Current Event DFP3 USB PE USB Power Enable Mode High: Enable Low: Off DFP4 USB PE USB Power Enable Mode High: Enable Low: Off DFP4 Over Current Detection Open Drain (3.3V Max); Pin must High: Normal Low: Port Over Current Event - 18 - be pulled high if NC. be pulled high if NC. be pulled high if NC. be pulled high if NC. be pulled high if NC. VL822 USB 3.1 Gen2 Hub Controller Side Band Signal and Miscellaneous Pin Name Pin # I/O GPIO0 / HID0 / ATT0 67 I/O GPIO1 / HID1 / ORI0 68 I/O GPIO2 / HID2 / ATT1 69 I/O GPIO3 / HID3 / ORI1 70 I/O GPIO4 / HID4 / ATT4 71 I/O GPIO5 / EXTPWRON / WAKE / ORI4 73 I/O GPIO6 74 I/O RESET# 78 I USBLED1/SPISI 79 I/O USBLED2/SPICLK 80 I/O USBLED3/SPISO 81 I/O USBLED4/SPICS 82 I/O VBUSDET0 49 I Signal Description GPIO / HID Shared Pin. Available for GPIO Use, Config via Firmware Setting. Available for HID button Use, Config via Firmware Setting. UFP Host Attach Status Input Pin, Refer to Appendix-2. GPIO / HID Shared Pin. Available for GPIO Use, Config via Firmware Setting. Available for HID button Use, Config via Firmware Setting. UFP Mux Orientation Setting Input Pin, Refer to Appendix-2. GPIO / HID Shared Pin. Available for GPIO Use, Config via Firmware Setting. Available for HID button Use, Config via Firmware Setting. DFP1 Device Attach Status Input Pin, Refer to Appendix-2. GPIO / HID Shared Pin. Available for GPIO Use, Config via Firmware Setting. Available for HID button Use, Config via Firmware Setting. DFP1 Mux Orientation Setting Input Pin, Refer to Appendix-2. GPIO / HID Shared Pin. Available for GPIO Use, Config via Firmware Setting. Available for HID button Use, Config via Firmware Setting. DFP4 Device Attach Status Input Pin, Refer to Appendix-2. GPIO / External Power Status / Wake Shared pin. Available for GPIO Use, Config via Firmware Setting. DC Jack Power Source Insert Detection (3.3V Max). Available for Connected Standby use, Config via Firmware Setting. DFP4 Mux Orientation Setting Input Pin, Refer to Appendix-2. GPIO Available for GPIO Use, Config via Firmware Setting. Reset Input of Hub Controller Low: Reset High: Normal Operation Power On sequence, Refer to Appendix-1. DFP1 LED Indicator / SPISI shared pin. Active High Output for LED Use. DFP2 LED Indicator / SPISCLK shared pin. Active High Output for LED Use. DFP3 LED Indicator / SPISO shared pin. Active High Output for LED Use. DFP4 LED Indicator / SPICS shared pin. Active High Output for LED Use UFP Vbus Detection (3.3V Max) - 19 - VL822 USB 3.1 Gen2 Hub Controller Pinout (VL822-Q5) Figure 6 – VL822-Q5 Pin Diagram - 20 - VL822 USB 3.1 Gen2 Hub Controller Pin List (VL822-Q5) Table 3 – VL822-Q5 Pin List Pin Pin Name Pin Pin Name 1 SSTX1+ 29 VCC33I 2 SSTX1– 30 REXT 3 VCC10I 31 VDD 4 SSRX1+ 32 SSTX0– 5 SSRX1– 33 SSTX0+ 6 VCC10I 34 VCC10I 7 HSD1+ 35 SSRX0– 8 HSD1– 36 SSRX0+ 9 VDD 37 VCC10I 10 SSTX2+ 38 HSD0+ 11 SSTX2– 39 HSD0– 12 VCC10I 40 GPIO0/HID0 13 SSRX2+ 41 VCC33I 14 SSRX2– 42 GPIO6 / USBSUS 15 VCC33I 43 GPIO7 / SMDAT 16 HSD2+ 44 GPIO8 / SMCLK 17 HSD2– 45 VDD 18 GPIO/SDA3 46 RESET# 19 GPIO/SCL3 47 USBLED1 / SPISI 20 VCC33I 48 USBLED2 / SPICK 21 VCC10I 49 SPISO 22 VDD 50 SPICS 23 VCC10I 51 VCC33I 24 USB3XI 52 TESTEN 25 USB3XO 53 USBOC2 26 VBUSDET0 54 USBPE2 27 GPIO/SCL4 55 USBOC1 28 GPIO/SDA4 56 USBPE1 - 21 - VL822 USB 3.1 Gen2 Hub Controller Pin Descriptions (VL822-Q5) Signal Type Definition Name Type Signal Description Input I A logic input-only signal Output O A logic output only signal Input/ Output I/O A logic bi-directional signal Power PWR A power pin Ground GND A ground pin USB 3.1 Interface Pin Name Pin # I/O Signal Description SSTX0- 32 O USB 3.1 UFP Differential TX– SSTX0+ 33 O USB 3.1 UFP Differential TX+ SSRX0- 35 I USB 3.1 UFP Differential RX– SSRX0+ 36 I USB 3.1 UFP Differential RX+ SSTX1+ 1 O USB 3.1 DFP1 Differential TX+ SSTX1- 2 O USB 3.1 DFP1 Differential TX– SSRX1+ 4 I USB 3.1 DFP1 Differential RX+ SSRX1- 5 I USB 3.1 DFP1 Differential RX– SSTX2+ 10 O USB 3.1 DFP2 Differential TX+ SSTX2- 11 O USB 3.1 DFP2 Differential TX– SSRX2+ 13 I USB 3.1 DFP2 Differential RX+ SSRX2- 14 I USB 3.1 DFP2 Differential RX– Analog Command Block Pin Name Pin # I/O Signal Description USB3XO 25 O 25M Crystal Output USB3XI 24 I 25M Crystal Input REXT 30 I Connect to External Reference Resistor (12.4K+/- 1%) - 22 - VL822 USB 3.1 Gen2 Hub Controller Test Pin Pin Name Pin # I/O TESTEN 52 I GPIO7 / SMDAT 43 I/O GPIO8 / SMCLK 44 I/O Signal Description Test Mode Enable Low: Normal mode. High: Test mode. Available for GPIO Use, Config via Firmware Setting. SMBus data with Proprietary Data Format. (Open Drain) Pin must be pulled high if NC. Available for GPIO Use, Config via Firmware Setting. SMBus clock with Proprietary Data Format. (Open Drain) Pin must be pulled high if NC. USB 2.0 Interface Pin Name Pin # I/O Signal Description HSD0+ 38 I/O USB 2.0 UFP Differential D+ HSD0– 39 I/O USB 2.0 UFP Differential D– HSD1+ 7 I/O USB 2.0 DFP1 Differential D+ HSD1– 8 I/O USB 2.0 DFP1 Differential D– HSD2+ 16 I/O USB 2.0 DFP2 Differential D+ HSD2– 17 I/O USB 2.0 DFP2 Differential D– Power and Ground Pin Name Pin # I/O Signal Description GND EPAD GND Ground VDD 9, 22, 31, 45 PWR 1.05V Core Power VCC10I 3, 6, 12, 21, 23, 34, 37 PWR 1.05V Analog Power VCC33I 15, 20, 29, 41, 51 PWR 3.3V Analog Power Side Band Signal and Miscellaneous Pin Name Pin # I/O USBOC1 55 I or I/O USBPE1 56 O USBOC2 53 I or I/O USBPE2 54 O Signal Description DFP1 Over Current Detection Open Drain (3.3V Max); Pin must be pulled high if NC. High: Normal Low: Port Over Current Event DFP1 USB PE USB Power Enable Mode High: Enable Low: Off DFP2 Over Current Detection Open Drain (3.3V Max); Pin must be pulled high if NC. High: Normal Low: Port Over Current Event DFP2 USB PE USB Power Enable Mode High: Enable Low: Off - 23 - VL822 USB 3.1 Gen2 Hub Controller Side Band Signal and Miscellaneous Pin Name Pin # I/O Signal Description GPIO0 / HID0 40 I/O GPIO6 / USBSUS 42 I/O RESET# 46 I USBLED1 / SPISI 47 I/O USBLED2 / SPICLK 48 I/O SPISO 49 I/O SPISO pin. SPICS 50 I/O SPICS pin. VBUSDET0 26 I UFP Vbus Detection (3.3V Max) GPIO / HID Shared Pin. Available for GPIO Use, Config via Firmware Setting. Available for HID button Use, Config via Firmware Setting. GPIO Available for GPIO Use, Config via Firmware Setting. Reset Input of Hub Controller Low: Reset High: Normal Operation Power On sequence, Refer to Appendix-1. DFP1 LED Indicator / SPISI shared pin. Active High Output for LED Use. DFP2 LED Indicator / SPISCLK shared pin. Active High Output for LED Use. GPIO/SDA3 18 I or I/O GPIO / I2C Data Shared Pin. Available for GPIO Use, Config via Firmware Setting. Available for I2C Use, Config via Firmware Setting. Open Drain (3.3V Max); Pin must be pulled high if NC. GPIO/SCL3 19 O GPIO / I2C Clock Shared Pin. Available for GPIO Use, Config via Firmware Setting. Available for I2C Use, Config via Firmware Setting. GPIO/SDA4 28 I or I/O GPIO / I2C Data Shared Pin. Available for GPIO Use, Config via Firmware Setting. Available for I2C Use, Config via Firmware Setting. Open Drain (3.3V Max); Pin must be pulled high if NC. GPIO/SCL4 27 O GPIO / I2C Clock Shared Pin. Available for GPIO Use, Config via Firmware Setting. Available for I2C Use, Config via Firmware Setting. - 24 - VL822 USB 3.1 Gen2 Hub Controller Electrical Specification Absolute Maximum Rating Symbol Parameter Min Max Unit Note TSTG Storage Temperature -55 125 °C — V33 3.3V Power Supply Voltage -0.5 3.63 V — V10 1.05V Input Voltage -0.5 V — VIN Input voltage at I/O pins -0.5 1.1 (≦ 3.63) and (≦ V33+0.3) V — VESD Electrostatic Discharge -2000 2000 V θjc θja Thermal resistance between junction and case Thermal resistance between junction and ambient TBD °C/W TBD °C/W PD Power dissipation — TBD Note: Stress above conditions may cause permanent damage to the device. Functional operation of this device should be restricted to the conditions described. Human Body Model 4L PCB definitions follow JESD51-7 W Note: About thermal factors, Ta is the concerned ambient temperature, and θca = θja - θjc TJ = θja * PD + Ta Tc = θca * PD + Ta Operating Conditions Symbol Parameter Min Max Unit Note TA Ambient Temperature 0 70 °C — Tj Junction Temperature 0 125 °C — V33 3.3V Power Supply Voltage 3.0 3.6 V — V10 1.05V Input Voltage 1.0 1.1 V — VIL Input Low Voltage — 0.8 V — VIH Input High Voltage 2.3 — V — VOL Output Low Voltage — 0.4 V IOL=4mA VOH Output High Voltage 2.4 — V IOH=4mA IIL Input Leakage Current — +/-10 µA 0