郑州中景园电子技术有限公司
ZHENG ZHOU ZHONG JING YUAN TECHNOLOGY CO.,LTD
TEL：18601955397
Product Specification
Part Name:
OLED Display Module
Customer Part ID:
Zhong JingYuan ID: ZJY096S0700WG01
Ver: A
Customer:
Approved by
From: Zhong JingYuan technology Co.,Ltd.
Approved by
Notes:
1. Please contact Zhong JingYuan technology Co.,Ltd. before assigning your product based on this
module specification
2. The information contained herein is presented merely to indicate the characteristics and
performance
of our products. No responsibility is assumed by Zhong JingYuan technology Co.,Ltd. for any
intellectual property claims or other problems that may result from application based on the
module described herein.
1
https://oled-zjy.taobao.com
郑州中景园电子技术有限公司
ZHENG ZHOU ZHONG JING YUAN TECHNOLOGY CO.,LTD
TEL：18601955397
Revised History
Part Number
Revision
ZJY096S0700WG01
A
Revision Content
New
2020-06-06
2
https://oled-zjy.taobao.com
Revised on
郑州中景园电子技术有限公司
ZHENG ZHOU ZHONG JING YUAN TECHNOLOGY CO.,LTD
TEL：18601955397
TABLE OF Contents
Part Name: OLED Display Module................................................................................................................1
1. Basic Specifications.................................................................................................................................... 5
2.
3.
1.1
Display Specifications.................................................................................................................. 5
1.2
Mechanical Specifications........................................................................................................... 5
1.3
Active Area / Memory Mapping & Pixel Construction................................................................5
1.4
Mechanical Drawing....................................................................................................................6
1.5
Pin Definition...............................................................................................................................7
1.6
product picture............................................................................................................................7
1.7
Schematic Diagram....................................................................................................................8
Absolute Maximum Ratings......................................................................................................................9
Optics & Electrical Characteristics..........................................................................................................10
3.1
Optics Characteristics................................................................................................................10
3.2
DC Characteristics......................................................................................................................10
3.3
AC Characteristics......................................................................................................................11
3.3.1
4.
5.
6.
7.
SPI Interface Timing Characteristics:................................................................................11
Functional Specification.......................................................................................................................... 13
4.1
Commands.................................................................................................................................13
4.2
VCC Generated by Internal DC/DC Circuit.................................................................................14
Reliability...................................................................................................................................................18
5.1
Contents of Reliability Tests......................................................................................................18
5.2
Failure Check Standard..............................................................................................................18
Outgoing Quality Control Specifications.............................................................................................. 18
6.1
Environment Required.............................................................................................................. 18
6.2
Sampling Plan............................................................................................................................ 19
6.3
Criteria & Acceptable Quality Level.......................................................................................... 19
6.3.1
Cosmetic Check (Display Off) in Non-Active Area............................................................. 19
6.3.2
Cosmetic Check (Display Off) in Active Area..................................................................... 19
6.3.3
Pattern Check (Display On) in Active Area........................................................................ 21
Precautions When Using These OEL Display Modules........................................................................22
7.1
Handling Precautions................................................................................................................ 22
3
https://oled-zjy.taobao.com
郑州中景园电子技术有限公司
ZHENG ZHOU ZHONG JING YUAN TECHNOLOGY CO.,LTD
TEL：18601955397
7.2
Storage Precautions.................................................................................................................. 23
7.3
Designing Precautions............................................................................................................... 24
7.4
Precautions when disposing of the OEL display modules.........................................................24
7.5
Other Precautions..................................................................................................................... 24
Notice:...............................................................................................................................................................25
4
https://oled-zjy.taobao.com
郑州中景园电子技术有限公司
ZHENG ZHOU ZHONG JING YUAN TECHNOLOGY CO.,LTD
TEL：18601955397
1. Basic Specifications
1.1Display Specifications
1)
2)
3)
Display Mode:
Display Color:
Drive Duty:
Passive Matrix
Monochrome (White)
1/64 Duty
1.2Mechanical Specifications
1)
Outline Drawing:
According to the annexed outline drawing
2)
3)
4)
5)
6)
Number of Pixels:
PCB Size:
Active Area:
Pixel Pitch:
Pixel Size:
128 64
27.327.8 2.65 (mm)
21.744 10.864 (mm)
0.17 0.17 (mm)
0.154 0.154 (mm)
1.3Active Area / Memory Mapping & Pixel Construction
5
https://oled-zjy.taobao.com
4.27
6.37
6.65
10.86(AA)
19.26(PANEL)
23.80(HOLE)
27.80 (PCBA)
2.00
2.000
50
3.
?
4 - .0 0
2
4 -?
https://oled-zjy.taobao.com
14.00
1.50
6
NOTES:
1.DISPLAY TYPE: 0.96" OLED
2.VIEWING DIRECTION: All
3.POLARIZER MODE: TRANSMISSIVE/NORMALLY BLACK
4.DRIVER IC: SSD1306
5.Resolution：128x64
6.INTERFACE:SPI/IIC(The default is SPI interface)
7.VOLTAGE:3.3V
7.OPERATING TEMP: -40°C~70°C
6.65
27.30(PCBA)
26.70( PANEL)
23.30(HOLE)
21.74(AA)
1.45
1.20
2.65
Customer Approval
Signature
mm
Tolerance
Dimension ±0.3
Angle
±1
General Roughness
Unit
Unless Otherwise Specified
D1
RES
DC
CS
3
4
5
6
7
HBK
20190425
By
Drawn
E.E.
Panel / E.
ZJY096S0700WG01 PM OLED Display Module
Pixel Number: 128x64, Monochrome
Date
Title
Zhengzhou Zhongjingyuan Electronic Technology Co. LTD
郑州中景园电子技术有限公司
VCC
D0
2
GND
Pin Symbol
1
P.M.
A
Rev.
Scale
1:1
Sheet
1 of 1
Size
A4
Soda Lime / Polyimide
Material
Drawing Number
A
Pin Descriptions
Remark
Original Drawing
Date
20190425
Item
郑州中景园电子技术有限公司
ZHENG ZHOU ZHONG JING YUAN TECHNOLOGY CO.,LTD
TEL：18601955397
1.4Mechanical Drawing
郑州中景园电子技术有限公司
ZHENG ZHOU ZHONG JING YUAN TECHNOLOGY CO.,LTD
TEL：18601955397
1.5Pin Definition
PIN No.
Symbol
1
GND
2
VCC
3
4
SCL
SDA
5
RES
6
DC
7
CS
Description
Ground of Logic Circuit
This is a ground pin. It must be connected to ground
Power Supply for OLED
This is a voltage supply pin. It must be connected to source
The serial clock input SCL
The serial data input SDA
Power Reset for Controller and Driver
This pin is reset signal input. When the pin is low, initialization
of the chip is executed. Keep this pin pull high during normal
operation
Data/Command Control
This pin is Data/Command control pin. When the pin is pulled high,
the input at SDA is treated as display data. When the pin is pulled
low, the input at SDA will be transferred to the command register.
Chip Select
This pin is the chip select pin.Low enable, high disable.
1.6product picture
Top view
Bottom view
7
https://oled-zjy.taobao.com
郑州中景园电子技术有限公司
ZHENG ZHOU ZHONG JING YUAN TECHNOLOGY CO.,LTD
TEL：18601955397
1.7 Schematic Diagram
SPI Switch to IIC :
1. Change R3 to R1.
2. Ground DC pin and CS pin.
3. Use IIC program.
8
https://oled-zjy.taobao.com
郑州中景园电子技术有限公司
ZHENG ZHOU ZHONG JING YUAN TECHNOLOGY CO.,LTD
TEL：18601955397
2. Absolute Maximum Ratings
Parameter
Symbol
Min
Max
Unit
Notes
Supply Voltage for Display
VCC
3
5
V
1, 2
Supply Voltage for Logic
SCL/SDA/RES/DC/CS
1.65
3.3
V
Operating Temperature
TOP
-40
80
C
Storage Temperature
TSTG
-40
85
C
3
Life Time (120 cd/m2)
10,000
-
hour
4
2
30,000
-
hour
4
2
50,000
-
hour
4
Life Time (80 cd/m )
Life Time (60 cd/m )
Note 1: All the above voltages are on the basis of “GND = 0V”.
Note 2: When this module is used beyond the above absolute maximum ratings, permanent
breakage of the module may occur. Also, for normal operations, it is desirable to use this
module under the conditions according to Section 3. “Optics & Electrical Characteristics”.
If this module is used beyond these conditions, malfunctioning of the module can occur
and the reliability of the module may deteriorate.
Note 3: The defined temperature ranges do not include the polarizer. The maximum withstood
temperature of the polarizer should be 80C.
Note 4: VCC = 3.3 V, Ta = 25°C, 50% Checkerboard.
Software configuration follows Section 4.4 Initialization.
End of lifetime is specified as 50% of initial brightness reached. The average operating
lifetime at room temperature is estimated by the accelerated operation at high
temperature conditions.
9
https://oled-zjy.taobao.com
郑州中景园电子技术有限公司
ZHENG ZHOU ZHONG JING YUAN TECHNOLOGY CO.,LTD
TEL：18601955397
3.Optics & Electrical Characteristics
3.1Optics Characteristics
Characteristics
Symbol
Conditions
Min
Typ
Max
Unit
Lbr
Note 5
150
-
-
cd/m2
Lbr
Note 6
150
180
-
cd/m2
C.I.E.
(x)
(y)
C.I.E. 1931
0.28
0.31
0.32
0.35
0.36
0.39
Dark Room Contrast
CR
-
2000:1
-
-
Free
-
Brightness
(VCC Supplied Externally)
Brightness
(VCC Generated Internal
DC/DC)
Viewing Angle
degree
* Optical measurement taken at VDD = 2.8V, VCC = 7.25V.
Software configuration follows Section 4.2 Initialization.
3.2DC Characteristics
Characteristics
Symbol
Supply Voltage for Logic
VDD
Supply Voltage for Display
(Supplied Externally)
VCC
Supply Voltage for DC/DC
Min
Typ
Max
Unit
1.65
2.8
3.3
V
Note 5
(Internal DC/DC Disable)
11.5
12
12.5
V
VBAT
Internal DC/DC Enable
3.5
-
4.2
V
Supply Voltage for Display
(Generated by Internal
DC/DC)
VCC
Note 6
(Internal DC/DC Enable)
7.0
-
7.5
V
High Level Input
VIH
IOUT = 100μA, 3.3MHz
0.8xVDD
-
VDD
V
Low Level Input
VIL
IOUT = 100μA, 3.3MHz
0
-
0.2xVDD
V
High Level Output
VOH
IOUT = 100μA, 3.3MHz
0.9xVDD
-
VDD
V
Low Level Output
VOL
IOUT = 100μA, 3.3MHz
0
-
0.1xVDD
V
Operating Current for VDD
IDD
-
180
300
uA
Operating Current for VCC
(VCC Supplied Externally)
Operating Current for VBAT
(VCC Generated by Internal
Conditions
ICC
Note 7
-
9
15
mA
IBAT
Note 8
-
25.6
32
mA
10
https://oled-zjy.taobao.com
郑州中景园电子技术有限公司
ZHENG ZHOU ZHONG JING YUAN TECHNOLOGY CO.,LTD
TEL：18601955397
DC/DC)
Sleep Mode Current for VDD
IDD,SLEEP
-
1
5
uA
Sleep Mode Current for VCC
ICC,SLEEP
-
2
10
uA
Note 5 & 6: Brightness (Lbr) and Supply Voltage for Display (VPP) are subject to the change of the
panel characteristics and the customer’s request.
Note 7: VDD = 2.8V, VCC = 12V, 100% Display Area Turn on.
Note 8: VDD = 2.8V, VCC = 7.25V, 100% Display Area Turn on.
* Software configuration follows Section 4.2 Initialization.
3.3AC Characteristics
3.3.1
SPI Interface Timing Characteristics:
Symbol
tcycle
tCSS
tCSH
tDSW
tDHW
tCLKL
tCLKH
tR
tF
Description
Min
Max
Unit
Clock Cycle Time
100
-
ns
Chip Select Setup Time
20
-
ns
Chip Select Hold Time
10
-
ns
Write Data Setup Time
15
-
ns
Write Data Hold Time
15
-
ns
Clock Low Time
20
-
ns
Clock High Time
20
-
ns
Rise Time
-
40
ns
Fall Time
-
40
ns
* (VDD - VSS = 1.65V to 3.3V, Ta = 25°C)
11
https://oled-zjy.taobao.com
郑州中景园电子技术有限公司
ZHENG ZHOU ZHONG JING YUAN TECHNOLOGY CO.,LTD
TEL：18601955397
12
https://oled-zjy.taobao.com
郑州中景园电子技术有限公司
ZHENG ZHOU ZHONG JING YUAN TECHNOLOGY CO.,LTD
TEL：18601955397
4. Functional Specification
4.1Commands
D/C Hex
D
#
71
0
81
0
A[7:0] A7
D
60
A6
D
50
A5
D D3 D2
40
0
0
A4
A3
A2
D D0 Command
Description
10
1 Set Contrast Control Double byte command to select 1 out of
A1 A0
256 contrast steps. Contrast increases as
the value increases.
(RESET = 7Fh )
0
DB
1
1
0
1
1
0
1
1
0
A[7:0
0
A6
A5
A4
0
0
0
0
0
A6/A7 1
0
1
0
0
1
1
X0 Set
Normal/Inverse
Display
0
AE
AF
1
0
1
0
1
1
1
X0
0
A0/A1 1
0
1
0
0
0
0
X0 Set Segment
Re-map
A0h, X[0]=0b: column address 0 is
mapped to SEG0 (RESET)
A1h, X[0]=1b: column address 127 is
mapped to SEG0
0
C0/C8
1
0
0
X3
0
0
0
C0h, X[3]=0b: normal mode (RESET) Scan
from COM0 to COM[N –1]
C8h, X[3]=1b: remapped mode.
Scan from COM[N-1] to
COM0
Where N is the Multiplex ratio.
Set VCOMH Deselect
Level
]
1
000b
010b
011b
Hex
cod
00h
20h
30h
V COMH deselect level
~ 0.65 x VCC
~ 0.77 x VCC (RESET)
~ 0.83 x VCC
A6h, X[0]=0b: Normal display (RESET) 0
in RAM: OFF in display panel 1
in RAM: ON in display panel
A7h, X[0]=1b: Inverse display
0 in RAM: ON in display panel
1
in RAM: OFF
in (sleep
displaymode)
panel
OFF
Set Display ON/OFF AEh, X[0]=0b:Display
(RESET)
AFh X[0]=1b:Display ON in normal mode
Set COM
Output Scan
Direction
13
https://oled-zjy.taobao.com
A[6:4]
郑州中景园电子技术有限公司
ZHENG ZHOU ZHONG JING YUAN TECHNOLOGY CO.,LTD
TEL：18601955397
4.2VCC Generated by Internal DC/DC Circuit
If the noise is accidentally occurred at the displaying window during the operation, please reset the
display in order to recover the display function.
14
https://oled-zjy.taobao.com
郑州中景园电子技术有限公司
ZHENG ZHOU ZHONG JING YUAN TECHNOLOGY CO.,LTD
TEL：18601955397
Normal Operation
Power Stabilized
(100ms Delay Recommended)
Set Display Off
0xAE
Power down VBAT
(50ms Delay Recommended)
Set Charge Pump
0x8D, 0x10
Power down VDD
VDD/VBAT off State
Normal Operation
Set Charge Pump
0x8D, 0x10
Set Display Off
0xAE
Power down VBAT
Sleep Mode
Sleep Mode
Set Charge Pump
0x8D, 0x14
Power Stabilized
(100ms Delay Recommended)
Power up VBAT
(100ms Delay Recommended)
Set Display On
0xAF
Normal Operation
15
https://oled-zjy.taobao.com
郑州中景园电子技术有限公司
ZHENG ZHOU ZHONG JING YUAN TECHNOLOGY CO.,LTD
TEL：18601955397
void OLED_Init(void)
{
//OLED 复位
OLED_RES_Clr();//RES 置 0
delay_ms(200);//延时 200ms
OLED_RES_Set();//RES 置 1
//OLED 初始化
OLED_WR_Byte(0xAE,OLED_CMD);//--turn off oled panel
OLED_WR_Byte(0x00,OLED_CMD);//---set low column address
OLED_WR_Byte(0x10,OLED_CMD);//---set high column address
OLED_WR_Byte(0x40,OLED_CMD);//--set start line address
OLED_WR_Byte(0x81,OLED_CMD);//--set contrast control register
OLED_WR_Byte(0xCF,OLED_CMD);// Set SEG Output Current Brightness
OLED_WR_Byte(0xA1,OLED_CMD);//--Set SEG/Column Mapping
0xa0 左右反置
0xa1 正常
OLED_WR_Byte(0xC8,OLED_CMD);//Set COM/Row Scan Direction
0xc0 上下反置
0xc8 正常
OLED_WR_Byte(0xA6,OLED_CMD);//--set normal display
OLED_WR_Byte(0xA8,OLED_CMD);//--set multiplex ratio(1 to 64)
OLED_WR_Byte(0x3f,OLED_CMD);//--1/64 duty
OLED_WR_Byte(0xD3,OLED_CMD);//-set display offset Shift
Mapping
RAM
Counter (0x00~0x3F)
OLED_WR_Byte(0x00,OLED_CMD);//-not offset
OLED_WR_Byte(0xd5,OLED_CMD);//--set display clock divide ratio/oscillator
frequency
OLED_WR_Byte(0x80,OLED_CMD);//--set divide ratio, Set Clock as 100 Frames/Sec
OLED_WR_Byte(0xD9,OLED_CMD);//--set pre-charge period
OLED_WR_Byte(0xF1,OLED_CMD);//Set Pre-Charge as 15 Clocks & Discharge as 1
Clock
OLED_WR_Byte(0xDA,OLED_CMD);//--set com pins hardware configuration
OLED_WR_Byte(0x12,OLED_CMD);
OLED_WR_Byte(0xDB,OLED_CMD);//--set vcomh
OLED_WR_Byte(0x30,OLED_CMD);//Set VCOM Deselect Level
OLED_WR_Byte(0x20,OLED_CMD);//-Set Page Addressing Mode (0x00/0x01/0x02)
OLED_WR_Byte(0x02,OLED_CMD);//
OLED_WR_Byte(0x8D,OLED_CMD);//--set Charge Pump enable/disable
OLED_WR_Byte(0x14,OLED_CMD);//--set(0x10) disable
OLED_Clear();
16
https://oled-zjy.taobao.com
郑州中景园电子技术有限公司
ZHENG ZHOU ZHONG JING YUAN TECHNOLOGY CO.,LTD
TEL：18601955397
OLED_WR_Byte(0xAF,OLED_CMD);
}
#define OLED_CMD 0 //write command
#define OLED_DATA 1 //write data
void OLED_WR_Byte(u8 dat,u8 cmd)
{
u8 i;
if(cmd)
OLED_DC_Set();
else
OLED_DC_Clr();
OLED_CS_Clr();
for(i=0;i 0.1
L≤2
n≤1
L>2
n=0
Φ ≤ 0.1
Ignore
0.1 < Φ ≤ 0.25
n≤1
0.25 < Φ
n=0
Φ ≤ 0.5
Ignore if no Influence on Display
0.5 < Φ
n=0
Not Allowable
* Protective film should not be tear off when cosmetic check.
** Definition of W & L & Φ (Unit: mm): Φ = (a + b) / 2
L
b: Minor Axis
W
a: Major Axis
20
https://oled-zjy.taobao.com
郑州中景园电子技术有限公司
ZHENG ZHOU ZHONG JING YUAN TECHNOLOGY CO.,LTD
TEL：18601955397
6.3.3
Pattern Check (Display On) in Active Area
Check Item
Classification
No Display
Major
Missing Line
Major
Pixel Short
Major
Darker Pixel
Major
Wrong Display
Major
21
https://oled-zjy.taobao.com
Criteria
郑州中景园电子技术有限公司
ZHENG ZHOU ZHONG JING YUAN TECHNOLOGY CO.,LTD
TEL：18601955397
Un-uniform
Major
7. Precautions When Using These OEL Display
Modules
7.1Handling Precautions
1)
2)
3)
4)
5)
Since the display panel is being made of glass, do not apply mechanical impacts such us
dropping from a high position.
If the display panel is broken by some accident and the internal organic substance leaks
out, be careful not to inhale nor lick the organic substance.
If pressure is applied to the display surface or its neighborhood of the OEL display
module, the cell structure may be damaged and be careful not to apply pressure to these
sections.
The polarizer covering the surface of the OEL display module is soft and easily scratched.
Please be careful when handling the OEL display module.
When the surface of the polarizer of the OEL display module has soil, clean the surface.
It takes advantage of by using following adhesion tape.
* Scotch Mending Tape No. 810 or an equivalent
Never try to breathe upon the soiled surface nor wipe the surface using cloth containing solvent such as ethyl alcohol, since the
surface of the polarizer will become cloudy.
Also, pay attention that the following liquid and solvent may spoil the polarizer:
6)
* Water
* Ketone
* Aromatic Solvents
Hold OEL display module very carefully when placing OEL display module into the system
housing. Do not apply excessive stress or pressure to OEL display module. And, do not
over bend the film with electrode pattern layouts. These stresses will influence the
display performance. Also, secure sufficient rigidity for the outer cases.
22
https://oled-zjy.taobao.com
郑州中景园电子技术有限公司
ZHENG ZHOU ZHONG JING YUAN TECHNOLOGY CO.,LTD
TEL：18601955397
7)
8)
9)
10)
Do not apply stress to the driver IC and the surrounding molded sections.
Do not disassemble nor modify the OEL display module.
Do not apply input signals while the logic power is off.
Pay sufficient attention to the working environments when handing OEL display modules
to prevent occurrence of element breakage accidents by static electricity.
* Be sure to make human body grounding when handling OEL display modules.
* Be sure to ground tools to use or assembly such as soldering irons.
* To suppress generation of static electricity, avoid carrying out assembly work under dry
environments.
* Protective film is being applied to the surface of the display panel of the OEL display
module. Be careful since static electricity may be generated when exfoliating the
protective film.
11) Protection film is being applied to the surface of the display panel and removes the
protection film before assembling it. At this time, if the OEL display module has been
stored for a long period of time, residue adhesive material of the protection film may
remain on the surface of the display panel after removed of the film. In such case,
remove the residue material by the method introduced in the above Section 5).
12) If electric current is applied when the OEL display module is being dewed or when it is
placed under high humidity environments, the electrodes may be corroded and be
careful to avoid the above.
7.2Storage Precautions
1)
When storing OEL display modules, put them in static electricity preventive bags avoiding
exposure to direct sun light nor to lights of fluorescent lamps. and, also, avoiding high
temperature and high humidity environment or low temperature (less than 0 C)
environments. (We recommend you to store these modules in the packaged state when
they were shipped from ZhongJingYuan technology Co.,Ltd.)
At that time, be careful not to let water drops adhere to the packages or bags nor let dewing occur with them.
2)
If electric current is applied when water drops are adhering to the surface of the OEL
display module, when the OEL display module is being dewed or when it is placed under
high humidity environments, the electrodes may be corroded and be careful about the
above.
23
https://oled-zjy.taobao.com
郑州中景园电子技术有限公司
ZHENG ZHOU ZHONG JING YUAN TECHNOLOGY CO.,LTD
TEL：18601955397
7.3Designing Precautions
1)
The absolute maximum ratings are the ratings which cannot be exceeded for OEL display
module, and if these values are exceeded, panel damage may be happen.
2) To prevent occurrence of malfunctioning by noise, pay attention to satisfy the VIL and VIH
specifications and, at the same time, to make the signal line cable as short as possible.
3) We recommend you to install excess current preventive unit (fuses, etc.) to the power
circuit (VDD). (Recommend value: 0.5A)
4) Pay sufficient attention to avoid occurrence of mutual noise interference with the
neighboring devices.
5) As for EMI, take necessary measures on the equipment side basically.
6) When fastening the OEL display module, fasten the external plastic housing section.
7) If power supply to the OEL display module is forcibly shut down by such errors as taking
out the main battery while the OEL display panel is in operation, we cannot guarantee the
quality of this OEL display module.
8) The electric potential to be connected to the rear face of the IC chip should be as follows:
SSD1306
* Connection (contact) to any other potential than the above may lead to rupture of the IC.
7.4Precautions when disposing of the OEL display modules
1) Request the qualified companies to handle industrial wastes when disposing of the OEL display
modules. Or, when burning them, be sure to observe the environmental and hygienic laws and
regulations.
7.5Other Precautions
1)
2)
When an OEL display module is operated for a long of time with fixed pattern may
remain as an after image or slight contrast deviation may occur.
Nonetheless, if the operation is interrupted and left unused for a while, normal state can
be restored. Also, there will be no problem in the reliability of the module.
To protect OEL display modules from performance drops by static electricity rapture, etc.,
do not touch the following sections whenever possible while handling the OEL display
modules.
* Pins and electrodes
* Pattern layouts such as the FPC
24
https://oled-zjy.taobao.com
郑州中景园电子技术有限公司
ZHENG ZHOU ZHONG JING YUAN TECHNOLOGY CO.,LTD
TEL：18601955397
3)
With this OEL display module, the OEL driver is being exposed. Generally speaking,
semiconductor elements change their characteristics when light is radiated according to
the principle of the solar battery. Consequently, if this OEL driver is exposed to light,
malfunctioning may occur.
* Design the product and installation method so that the OEL driver may be shielded from light in
actual usage.
* Design the product and installation method so that the OEL driver may be shielded from light
during the inspection processes.
4)
5)
Although this OEL display module stores the operation state data by the commands and
the indication data, when excessive external noise, etc. enters into the module, the
internal status may be changed. It therefore is necessary to take appropriate measures
to suppress noise generation or to protect from influences of noise on the system design.
We recommend you to construct its software to make periodical refreshment of the
operation statuses (re-setting of the commands and re-transference of the display data)
to cope with catastrophic noise.
Warranty:
The warranty period shall last twelve (12) months from the date of delivery. Buyer shall be
completed to assemble all the processes within the effective twelve (12) months. ZhongJingYuan
technology Co.,Ltd. shall be liable for replacing any products which contain defective material or
process which do not conform to the product specification, applicable drawings and specifications
during the warranty period. All products must be preserved, handled and appearance to permit
efficient handling during warranty period. The warranty coverage would be exclusive while the
returned goods are out of the terms above.
Notice:
No part of this material may be reproduces or duplicated in any form or by any means without the
written permission of ZhongJingYuan technology Co.,Ltd. ZhongJingYuan technology Co.,Ltd.
reserves the right to make changes to this material without notice. ZhongJingYuan technology
Co.,Ltd. does not assume any liability of any kind arising out of any inaccuracies contained in this
material or due to its application or use in any product or circuit and, further, there is no
representation that this material is applicable to products requiring high level reliability, such as,
medical products. Moreover, no license to any intellectual property rights is granted by implication
or otherwise, and there is no representation or warranty that anything made in accordance with this
25
https://oled-zjy.taobao.com
郑州中景园电子技术有限公司
ZHENG ZHOU ZHONG JING YUAN TECHNOLOGY CO.,LTD
TEL：18601955397
material will be free from any patent or copyright infringement of a third party. This material or
portions thereof may contain technology or the subject relating to strategic products under the
control of Foreign Exchange and Foreign Trade Law of Taiwan and may require an export license from
the Ministry of International Trade and Industry or other approval from another government agency.
26
https://oled-zjy.taobao.com
工商网监
湘ICP备2023018690号
