GS1500M-SDK2-HW-R2

GS1500M 802.11 b/g/n LOW-POWER WI-FI MODULE DATA SHEET Reference: GS1500M-DS Version: SP-1.4 Date: November 2014 GS1500M DATA SHEET Information in this document is provided in connection with GainSpan products. No license, express or implied, to any intellectual property rights is granted by this document. GainSpan assumes no liability whatsoever, and disclaims any express or implied warranty, relating to sale and/or use of GainSpan products including liability or warranties relating to fitness for a particular purpose, merchantability, or infringement of any patent, copyright or other intellectual property right. GainSpan products are not authorized for use as critical components in medical, lifesaving, or life-sustaining applications GainSpan may make changes to specifications and product descriptions at any time, without notice. *Other names and brands may be claimed as the property of others. Copyright © 2014 by GainSpan Corporation All Rights Reserved. Version Date Remarks 0.1 12-Apr-11 0.9 10-Nov-11 0.95 27-Jan-12 0.98 26-Mar-12 Updated description for usage of MSPI interface 1.0 30-Oct-12 Updated ordering info for module rev 2.2 Added note related to module firmware in ordering section 1.1 4-Mar-13 Updated section 5.1.1 reflow profile info and package info 1.2 17-Sept-13 1.3 August 2014 Added figure and notations to describe the thermocouple locations on the GS1500M module. 1.4 November 2014 Added Pre-heat temperature starting point. See section 5.1.1 Surface Mount Assembly. Initial Release Modified Package and Layout Updated Artwork Updated Power Consumption Table Updated Sleep States Includes reflow profile information Updated power consumption numbers Updated section 5.1outline drawings and note to reflect up to date tolerances and module dimensions GAINSPAN CONFIDENTIAL PAGE 2 OF 50 GS1500M DATA SHEET Table of Contents 1 OVERVIEW ----------------------------------------------------------------------------------------- 7 1.1 Document Overview ------------------------------------------------------------------------------------------------------------ 7 1.2 Product Overview ---------------------------------------------------------------------------------------------------------------- 7 2 2.1 ARCHITECTURE ---------------------------------------------------------------------------------- 9 G1500M Block Diagram ------------------------------------------------------------------------------------------------------- 9 2.2 Block Diagram Description -------------------------------------------------------------------------------------------------- 9 2.2.1 Overview ----------------------------------------------------------------------------------------------------------------------- 9 2.2.2 Wireless LAN and System Control Subsystem ---------------------------------------------------------------- 10 2.2.3 Network Services Subsystem ----------------------------------------------------------------------------------------- 10 2.2.4 Memory Subsystem ------------------------------------------------------------------------------------------------------- 10 2.2.5 Clock Circuitries ------------------------------------------------------------------------------------------------------------ 10 2.3 Peripherals ------------------------------------------------------------------------------------------------------------------------- 13 2.3.1 SPI ------------------------------------------------------------------------------------------------------------------------------- 13 2 2.3.2 I C -------------------------------------------------------------------------------------------------------------------------------- 14 2.3.3 UART --------------------------------------------------------------------------------------------------------------------------- 15 2.3.4 JTAG ---------------------------------------------------------------------------------------------------------------------------- 15 2.3.5 GPIO & LED Driver / GPIO -------------------------------------------------------------------------------------------- 16 2.3.6 ADC ----------------------------------------------------------------------------------------------------------------------------- 16 2.4 3 System States --------------------------------------------------------------------------------------------------------------------- 17 PIN-OUT AND SIGNAL DESCRIPTION ---------------------------------------------------- 20 3.1 GS1500M Device Pin-out Diagram (Module top view) --------------------------------------------------------- 20 3.1.1 GS1500M Module Pins Description -------------------------------------------------------------------------------- 21 3.1.2 Example Module Pin Connections ---------------------------------------------------------------------------------- 24 3.2 4 Power Supply Connections ------------------------------------------------------------------------------------------------ 25 ELECTRICAL CHARACTERISTICS--------------------------------------------------------- 27 4.1 Absolute Maximum Ratings ------------------------------------------------------------------------------------------------ 27 4.2 Operating Conditions --------------------------------------------------------------------------------------------------------- 27 4.3 Internal 1.8V regulator -------------------------------------------------------------------------------------------------------- 27 4.4 I/O DC Specifications ---------------------------------------------------------------------------------------------------------- 28 4.4.1 Digital Input Specifications --------------------------------------------------------------------------------------------- 28 4.4.2 Digital Output Specification -------------------------------------------------------------------------------------------- 28 4.4.3 I/O Digital Specifications (Tri-State) -------------------------------------------------------------------------------- 28 4.4.4 RTC Input Specifications (with Schmitt Trigger) --------------------------------------------------------------- 29 GAINSPAN CONFIDENTIAL PAGE 3 OF 50 GS1500M DATA SHEET 4.4.5 RTC Output Specifications --------------------------------------------------------------------------------------------- 29 4.5 Power Consumption ----------------------------------------------------------------------------------------------------------- 30 4.6 Radio Parameters --------------------------------------------------------------------------------------------------------------- 30 4.7 ADC Parameters ----------------------------------------------------------------------------------------------------------------- 31 4.8 SPI Interface Timing ----------------------------------------------------------------------------------------------------------- 32 4.8.1 Motorola SPI, clock polarity SPO = 0, clock phase SPH = 0 --------------------------------------------- 32 4.8.2 Motorola SPI, clock polarity SPO = 0, clock phase SPH = 1 --------------------------------------------- 34 4.8.3 Motorola SPI, clock polarity SPO = 1, clock phase SPH = 0 --------------------------------------------- 36 4.8.4 Motorola SPI, clock polarity SPO = 1, clock phase SPH = 1 --------------------------------------------- 38 5 PACKAGE AND LAYOUT GUIDELINES -------------------------------------------------- 40 5.1 GS1500M Recommended PCB Footprint and Dimensions ------------------------------------------------- 40 5.1.1 Surface Mount Assembly ----------------------------------------------------------------------------------------------- 42 6 ORDERING INFORMATION ------------------------------------------------------------------- 46 7 REGULATORY NOTES------------------------------------------------------------------------- 47 8 LIMITATIONS ------------------------------------------------------------------------------------- 49 9 REFERENCES ------------------------------------------------------------------------------------ 50 GAINSPAN CONFIDENTIAL PAGE 4 OF 50 GS1500M DATA SHEET Figures Figure 2-1: GS1500M Block Diagram ........................................................................................................ 9 Figure 2-2: RTC Interface Diagram .......................................................................................................... 12 Figure 2-3: GS1500M System States ........................................................................................................ 17 Figure 3-1: GS1500M Device Pin-out Diagram (Module top view)......................................................... 20 Figure 3-2: Module pin connection diagram ............................................................................................. 24 Figure 3-3 : GS1500M Always ON Power Supply Connection ................................................................ 25 Figure 3-4 : GS1500M with 3.3V IO and Standby Support ...................................................................... 26 Figure 4-1: timing diagram, Master mode, SPO=SPH=0......................................................................... 32 Figure 4-2: timing diagram, Slave mode, SPO=SPH=0. .......................................................................... 33 Figure 4-3: timing diagram, Master, SPO=0, SPH=1................................................................................ 34 Figure 4-4: timing diagram, Slave, SPO=0, SPH=1. ................................................................................. 35 Figure 4-5: timing diagram, Master mode, SPO=1, SPH=0. ..................................................................... 36 Figure 4-6: timing diagram, Slave mode, SPO=1, SPH=0. ....................................................................... 37 Figure 4-7: timing diagram, Master mode, SPO=SPH=1.......................................................................... 38 Figure 4-8: timing diagram, Slave mode, SPO=SPH=1. ........................................................................... 39 Figure 5-1: GS1500M Module Recommended PCB Footprint (dimensions are in inches) ..................... 40 Figure 5-2: GS1500M Module Dimensions (in inches) ........................................................................... 41 Figure 5-3: Reflow temperature profile. ................................................................................................... 42 Figure 5-4: Thermocouple Locations ........................................................................................................ 44 GAINSPAN CONFIDENTIAL PAGE 5 OF 50 GS1500M DATA SHEET Tables Table 3-1: Signal Description .................................................................................................................... 23 Table 4-1: Absolute Maximum Ratings .................................................................................................... 27 Table 4-2: Operating Conditions ............................................................................................................... 27 Table 4-3: Internal 1.8V Regulator ........................................................................................................... 27 Table 4-4: Digital Input Parameters .......................................................................................................... 28 Table 4-5: Digital Output Parameters........................................................................................................ 28 Table 4-6: I/O Digital Parameters ............................................................................................................. 29 Table 4-7: RTC Input Parameters.............................................................................................................. 29 Table 4-8: RTC Output Parameters ........................................................................................................... 29 Table 4-9: Power Consumption in Different States................................................................................... 30 Table 4-10: Radio Parameters ................................................................................................................... 30 Table 4-11: ADC Parameters .................................................................................................................... 31 Table 4-12: timing parameters, Master mode, SPO=SPH=0. ................................................................... 32 Table 4-13: timing parameters, Slave mode, SPO=SPH=0. ..................................................................... 33 Table 4-14: timing parameters, Master mode; SPO=0, SPH=1. ............................................................... 34 Table 4-15: timing parameters, Slave mode, SPO=0, SPH=1. .................................................................. 35 Table 4-16: timing parameters, Master mode, SPO=1, SPH=0................................................................ 36 Table 4-17: timing parameters, Slave mode, SPO=1, SPH=0. .................................................................. 37 Table 4-18: timing parameters, Master mode, SPO=SPH=1. ................................................................... 38 Table 4-19: timing parameters, Master mode, SPO=SPH=1. ................................................................... 39 Table 5-1: Recommended reflow parameters........................................................................................... 42 GAINSPAN CONFIDENTIAL PAGE 6 OF 50 GS1500M DATA SHEET 1 Overview 1.1 Document Overview the GS1500M Low Power module hardware specification. The GS1500M Tmodule providesdescribes a cost effective, low power, and flexible platform to add Wi-Fi® connectivity for HIS DOCUMENT embedded devices for a variety of applications, such as wireless sensors and thermostats. It combines ARM7-based processors with an RF transceiver, 802.11 MAC, security, & PHY functions, FLASH and SRAM, onboard and off module certified antenna options, and various RF front end options for end customer range needs in order to provide a WiFi and regulatory certified IEEE 802.11 radio with concurrent application processing services for variety of applications, while leverage existing 802.11 [1] wireless network infrastructures. 1.2 Product Overview ► GS1500M module: • • Dimensions are 1.450 inches by 0.900 inches by 0.143 inches (Length * Width * Height) 48pin Dual Flat pack PCB Surface Mount Package. Simple API for embedded markets covering large areas of applications ► Compliant with IEEE 802.11and regulatory domains: • • • Fully compatible with IEEE 802.11b/g/n. o DSSS modulation for data rate of 1 Mb/s and 2 Mb/s; CCK modulation rates of 5.5 and 11 Mb/s. o OFDM modulation for data rates of 6, 9, 12, 18, 24, 36, 48 and 54 Mb/s. o 802.11n 1x1 HT20 for data rates of MCS0 – 7. Supports short preamble and short slot times. WiFi Certified Solution o Supports 802.11i security  WPA™ - Enterprise, Personal  WPA2™ - Enterprise, Personal  Vendor EAP Type(s) • EAP-TTLS/MSCHAPv2, PEAPv0/EAP-MSCHAPv2, PEAPv1/EAPGTC, EAP-FAST, EAP-TLS Hardware encryption/decryption engines for WEP, WPA/WPA2 (AES and TKIP) RoHS and CE compliant • FCC/IC/ETSI Certified • • ► Dual ARM7 Processor Platform: • • • • 1st ARM7 processor (WLAN CPU) for WLAN software 2nd ARM7 (APP CPU) for networking software Based on Advanced Microprocessor Bus Architecture (AMBA) system: o AMBA High-Speed Bus (AHB). o AMBA Peripheral Bus (APB). On-chip WLAN boot code located in dedicated boot ROM. GAINSPAN CONFIDENTIAL PAGE 7 OF 50 GS1500M DATA SHEET ► Interfaces: • • • • • • • • • • PCB or external antenna options, electronically selected. Two SPI interfaces o One Master SPI for external flash memory device only o One Slave SPI interface (which can be configured as master, or slave or fast slave SPI). This interface can be used for external CPU interface, or for sensors and memory.. Two multi-purpose UART interfaces. Up to 23 configure able general purpose I/Os. Single 3.3V supply option One PWM output I2C master/slave interface. Two 10-bit ADC channels, aggregate sample rate 32 kS/s. Two alarm inputs to asynchronously awaken the chip. Support of up to two control outputs for power supply and sensors. ► Embedded RTC (Real Time Clock) can run directly from battery. ► Power supply monitoring capability. ► Low-power mode operations ► Standby, Sleep and Deep Sleep GAINSPAN CONFIDENTIAL PAGE 8 OF 50 GS1500M DATA SHEET 2 Architecture 2.1 G1500M Block Diagram Figure 2-1: GS1500M Block Diagram 2.2 Block Diagram Description 2.2.1 Overview • The GS1500M module includes: o a highly integrated IEEE 802.11b/g/n WLAN chip, which contains a MAC, baseband, security and radio functions in a single package o a GS1011 Chip (ultra-low power Wi-Fi system-on-chip (SOC), containing two ARM7based processors (one dedicated to Networking services, and the other dedicated to Wireless services), on-chip flash memory and SRAM in a single package • The module carries an 802.11b/g/n radio with onboard 32 KHz & 44 MHz crystal circuitries, RF, and certified PCB antenna or external antenna options. • Variety of interfaces are available such as two UART blocks using only two data lines per port with optional hardware flow controls, two SPI block, I2C with Master or slave operation, JTAG port, low-power 10-bit ADC capable of running at up to 32 KSamples/sec., GPIO’s, and LED Drivers/GPIO with 20mA capabilities. • GS1500M requires an always available power source on the VBAT pin, which powers the Real Time Clock (RTC). Frequently this is connected directly to a battery. The GS1500M contains a 1.8V regulator, which is turned on and off by the EV_1V8 pin. In systems that enable standby GAINSPAN CONFIDENTIAL PAGE 9 OF 50 GS1500M DATA SHEET mode, this pin is driven from the DC_DC_CNTL pin. The GS1500M also has a VDDIO power supply input that provides the logic signal level for the I/O pins. VDDIO must turn on and off with the 1.8V power. So, if the 1.8V power is controlled by the DC_DC_CNTL signal, then the DC_DC_CNTL signal also must turn VDDIO and VIN 3V3 on and off. The VIN_3V3 pin provides the input power for the 1.8V regulator. In addition this pin provides power for the external 802.11 radio. 2.2.2 Wireless LAN and System Control Subsystem The GS1500M Wireless LAN and system control subsystem consists of an ARM7 TDMI-S CPU providing system control functions which provides for control and management functions of the external 802.11b/g/n WLAN chip. 2.2.3 Network Services Subsystem 2.2.3.1 APP CPU The Network services subsystem consists of an APP CPU which is based on an ARM7 TDMI-S core. It incorporates an AHB interface and a JTAG debug interface. The network RTOS, network stack, and customer application code can reside on this CPU. For more information, consult the GS1011 Peripheral and Register Description [2] and GS1011 SoC data sheet [3] for detailed descriptions. 2.2.4 Memory Subsystem 2.2.4.1 Overview The GS1500M module contains several memory blocks: ► Boot ROM blocks. ► The software contained in this ROM provides the capability to download new firmware via the SPI Slave or UART interfaces and to control the update of WLAN and APP Flash Memory. ► 384 Kbytes of Embedded Flash to store program code. ► Three embedded Flash blocks of 128K bytes each ► WLAN Flash (contains the wireless LAN and system control subsystem software) ► APP Flash 0 and 1 (contain the Network/Application Software) ► 128 Kbytes of RAM shared between the two integrated CPU’s. ► 512 bytes of RTC memory ((retains data in all states, as long as the battery or other voltage supply is present) For more information, consult the GS1011 Peripheral and Register Description [2] and GS1011 SoC data sheet [3] for detailed descriptions. 2.2.5 Clock Circuitries The GS1500M architecture uses a low-power oscillator (i.e. 32 kHz) to provide a minimal subset of functions when the chip is in its low-power deep sleep mode, and a high-speed 44 MHz oscillator to provide clock signals for the processors, bus, and interfaces during active operation. Intermediate modes of operation, in which the 44 MHz oscillator is active but some modules are inactive, are obtained by gating the clock signal to different subsystems. The Clock & Reset Controller, within the device, is GAINSPAN CONFIDENTIAL PAGE 10 OF 50 GS1500M DATA SHEET responsible for generation, selection and gating of the clocks used in the module to reduce power consumption in various power states. 2.2.5.1 Real Time Clock (RTC) Overview To provide global time (and date) to the system, the GS1500M is equipped with a low-power Real Time Clock (RTC). RTC key features include: ► 32.768 kHz crystal support. ► Two external alarm inputs to wake up the device. ► Two programmable periodic outputs (one for a DC/DC regulator and one for a sensor). ► Embedded 128x32 non-volatile (battery-powered) RAM. ► Embedded Power On Reset. ► Real Time Counter (48 bits; 46 bits effective). An overview of RTC block diagram is shown in Figure 2-3. The RTC contains a low-power oscillator that can use 32.768 kHz crystals. In normal operation the RTC is always powered up, even in the Power Up state (see Figure 2-3). Two programmable embedded alarm counters (wrap-around) are provided to enable periodic wake-up of the remainder of the system, and one independent external component (typically a sensor). Two external alarm inputs enable wake-up of the system on external events. The global times are recorded on each external event and if the system is in the Power-ON state (see Figure 2-8), an interrupt is provided. The RTC includes a Power-On Reset (POR) circuit, to eliminate the need for an external component. The RTC contains low-leakage non-volatile (battery-powered) RAM, to enable storage of data that needs to be preserved. Total current consumption of the RTC in the worst case is typically less than 5 µA without data storage, using the 32.768 kHz oscillator. GAINSPAN CONFIDENTIAL PAGE 11 OF 50 GS1500M DATA SHEET Figure 2-2: RTC Interface Diagram Resolution of the wake-up timer is one clock cycle, and, with onboard 32KHz. CLK, each 32bit effective register can provide up to 1.5 days’ worth of standby duration as the longest standby period. Polarity of the rtc_out1 pin is programmable. 2.2.5.2 Real Time Counter The Real Time Counter features: ► 48-bit length (with absolute duration dependent on the crystal frequency used). ► Low-power design. This counter is automatically reset by power-on-reset. This counter wraps around (returns to “all-0” once it has reached the highest possible “all-1” value). 2.2.5.3 RTC Outputs There are two RTC outputs (dc_dc_cntl and rtc_out1) that can be used to control external devices, such as sensors or voltage regulators. For more information, consult the GS1011 Peripheral and Register Description for detailed descriptions. GAINSPAN CONFIDENTIAL PAGE 12 OF 50 GS1500M DATA SHEET 2.2.5.3.1 DC_DC_CNTL During RTC Power-on-Reset (e.g. when the battery is connected), the dc_dc_cntl pin is held low; it goes high to indicate completion of RTC power-on-reset. This pin can be used as an enable into an external device such as voltage regulator. For more information, consult the GS1011 Peripheral and Register Description for detailed descriptions. 2.2.5.3.2 RTC_OUT1 The rtc_out1 signal can be disabled or driven by the Wake-up Counter 2. This counter is 34 bits long, and operates in the same fashion as Wake-up Counter 1. The rtc_out1 signal can be configured to output the low-power crystal oscillator clock (i.e. the 32 kHz clock) instead of a simple state transition. Wakeup Counter 2 is automatically reset at Power-on-Reset. For more information, consult the GS1011 Peripheral and Register Description for detailed descriptions. 2.2.5.4 RTC Alarm Inputs 1 and 2 The RTC inputs alarm1 and alarm2 operate as follows: ► dc_dc_cntl is set to “1” (typically enabling the power supply to the rest of the GS1500M) whenever either of these inputs changes state. ► The RTC counter value is stored each time either of these inputs changes state. The inputs alarm1 and alarm2 have programmable polarity. Their task is to wake up the system (by setting dc_dc_cntl output pin to “1”) when an external event occurs. For more information, consult the GS1011 Peripheral and Register Description [2] and GS1011 SoC data sheet [3] for detailed descriptions. 2.3 Peripherals Note: For register identification and additional details on the use of shared peripherals, refer to the GS1011 Peripheral and Register Description [3]. 2.3.1 SPI There are two SPI interfaces. The Master SPI (MSPI) is used by WLAN CPU to communicate to external flash memory device only. The MSPI interface cannot be controlled directly by the APP CPU and hence the MSPI interface cannot be used for general purpose SPI devices The Slave SPI (SSPI) is general purpose and is configurable as master, slave or fast slave SPI. The SSPI interface could be used for external sensors, memory, or external CPU interface; The Fast SPI Slave is not shared, and is accessible only by the APP CPU. The Fast SPI operates only in the Motorolacompatible SPI slave mode, using 8-bit words and a 64-word FIFO buffer for both transmit and receive. The Serial to Wi-Fi firmware which uses SPI interface uses this Fast SPI mode. The recommended host clock speed when using the Serial to Wi-Fi firmware with SPI interface is 1.4MHz. Each block provides synchronous serial communication with slave or master devices, using one of the following protocols: ► Motorola Serial Peripheral Interface (SPI). ► Texas Instruments Synchronous Serial Protocol (SSP). ► National Semiconductor Microwire Protocol. Only Motorola Serial Peripheral Interface (SPI) timing is shown in this data sheet; however, National Semiconductor Microwire Protocol or Texas Instruments Synchronous Serial Protocol (SSP) modes are certainly supported. The SPI interface can also be used to access non-volatile external memory, such as an EEPROM block. The interface uses the SPI master mode to allow easy connection to industrystandard EEPROMs. GAINSPAN CONFIDENTIAL PAGE 13 OF 50 GS1500M DATA SHEET The SPI block provides the following general features: ► 32-bit AMBA APB interface to allow access to data, control, and status information by the host processor. ► Full-duplex serial-master or serial-slave operation. ► Two clock design: • APB bus clock for bus interface and registers. • Serial input clock for core logic. ► The Slave SPI block supports connections of external EEPROM or other non-volatile memory when used in Master mode. ► Programmable choice of Motorola SPI, Texas Instruments Synchronous Serial Protocol or National Semiconductor Microwire. ► Programmable control of the serial bit rate of the data transfer in serial-master mode of operation. ► Programmable phase and polarity of the bit rate clock. ► Programmable transfer modes to perform transmit and receive, transmit only, receive only and EEPROM read transfers. ► Programmable data word size (8, 16, 24 & 32 bits) for each data transfer. ► Transmit and receive FIFO buffer depth 8 words (of the selected size). ► Configurable number of slave select outputs in serial-master mode of operation: 1 to 4 serial slave- select output signals can be generated. ► Combined interrupt line with independent masking of interrupts. ► Transmit FIFO overflow, transmit FIFO empty, transmit FIFO underflow, receive FIFO full, receive FIFO underflow, receive FIFO overflow, and receive FIFO timeout interrupts. ► Transmit FIFO empty and receive FIFO full interrupts provide programmable threshold values. Both SPI blocks are configured to provide a FIFO depth of eight entries. The SPI slave interface can be used to provide control of the GS1500M from an external CPU. In master mode SPI chip select (MSPI_CS0 or MSPI_CS1) signals frame each data word. If the chip select is required to remain asserted for multiple data words, then a GPIO pin should be used for the chip select instead of the SPI chip select signals. For clock architecture and rates, please refer to section 7.1 Clock Architecture of GS1011 Peripheral and Register Description [2]. For other SPI Interface Timing, please refer to section 4.8. 2.3.2 I2C The I2C block provides a two-wire I2C serial interface. It provides the following features: ► 32-bit AMBA APB interface to allow access to data, control, and status Information by the host processor. ► Serial 2-wire I C bus, compliant to the I C Bus Specification Version 2.1. 2 2 ► Supports only one transfer in Standard mode (100 Kb/s) and fast speed mode with a bit rate of up to 392 Kb/s. ► Supports Multi-Master System Architecture through I C bus SCL line Synchronization and 2 Arbitration. GAINSPAN CONFIDENTIAL PAGE 14 OF 50 GS1500M DATA SHEET ► Transmitter and Receiver: The I C block can act as the Transmitter or Receiver depending on the 2 operation being performed. ► Master or slave I C operation. 2 ► 7- or 10-bit addressing. ► Ignores CBUS addresses (an older ancestor of I C that used to share the I C bus). 2 2 ► Interrupt or polled mode operation. ► Combined interrupt line triggered by: • • • • • • • • Tx FIFO not FULL. Rx FIFO not EMPTY. Rx FIFO FULL (can be used to transfer data by host interface in bursts). Tx FIFO EMPTY (can be used to transfer data by host interface in bursts). Rx FIFO OVER RUN. Master mode to Slave Transfer Request. Slave Transmit Request. Break Interrupt (master mode): No Acknowledge received from slave for slave address or write data. ► Digital de-bounce logic for the received SDA and SCL lines. ► Hold Delay Insertion on SDA line. 2.3.3 UART The GS1500M includes two UART blocks. Each UART block provides an asynchronous communication interface, using only two data lines: Rx data and Tx data. Hardware flow control using RTS/CTS signaling is provided as an option. The UART is a standard asynchronous serial interface, 16450/16550 compatible. It provides the following features: ► Operation in full-duplex mode. ► All standard bit rates up to 921.6 kbps are supported. ► RTS/CTS flow control handshake (standard 16550 approach). ► 5, 6, 7 and 8-bit character format. ► 1 or 2 stop bits (1.5 in case of a 5-bit character format). ► Parity bit: none, even, odd, mark, or space. ► 16-byte Rx and 16-byte Tx FIFOs. The UART Serial port can be used to communicate with a PC or other devices, for debug or additional functionality. 2.3.4 JTAG The JTAG ports facilitate debugging of the board and system designs. This block has the following features: ► Compliant to IEEE-1149.1 TAP ports. ► One JTAG boundary scans TAP port. ► One set of JTAG pins, which support the following mode of operation: GAINSPAN CONFIDENTIAL PAGE 15 OF 50 GS1500M DATA SHEET • APP ARM7TDMI-S Debug Mode. 2.3.5 GPIO & LED Driver / GPIO The GPIO ports are referenced to VDDIO. Two GPIO pins called GPIO30_LED1 & GPO31_LED2 have the capability to sink/source 20 mA typical (VDDIO=3.3V) to connect to devices such as switch contacts or LEDs. I2C_DATA/GPIO8 & I2C_CLK/GPIO9 have the capability to sink/source 12 mA typical (VDDIO=3.3V). Other GPIO’s have the capability to sink/source 4 mA typical (VDDIO=3.3V). All inputs are capable of generating processor interrupts. They can be individually programmed to provide edge- or level-triggered interrupts. For details on configuring GPIO ports, refer to the GS1011 Peripheral and Register Description [2]. 2.3.6 ADC The ADC is a 10-bit, low-power, A-to-D converter capable of running at up to 32 ksps. The ADC contains an internal band-gap reference which provides a stable 1.2 V reference voltage. The ADC can be programmed to use the 1.8 V supply as the full-scale reference. The ADC uses an input clock with a maximum frequency of 1 MHz. A conversion requires 32 clock cycles. When the internal band-gap reference is used, the reported integer Value at temperature T (ºC) is related to the voltage Vactual at the input pin as:  1.2444 − 0.00014 (25 − T ) Vactual = Value    1023 When the 1.8V supply voltage is used as the reference, the corresponding relation is: − 0.036  V Vactual = Value  DD, ADC   1023 To reduce power consumption the ADC can be disabled automatically between periodic measurements and after single measurements. For more information, consult the GS1011 Peripheral and Register Description [2] and GS1011 SoC data sheet [3] for detailed descriptions. GAINSPAN CONFIDENTIAL PAGE 16 OF 50 GS1500M DATA SHEET 2.4 System States Figure 2-8 shows the power management/clock states of the GS1500M system. Figure 2-3: GS1500M System States The system states of the GS1500M system are as follows: Power OFF: No power source connected to the system. I/O’s should not be driven high by an external device during this state. Standby: In the standby state, only the RTC portion of the GS1500M is powered from the VBAT pin. The other power supplies are turned off by the DC_DC_CNTL pin being low. Power supplies which MUST be powered on and off together, controlled by the DC_DC_CNTL pin, include the EN_1V8 pin (which controls VOUT_1V8), VDDIO, and the VIN_3V3 pin. In standby state the 32.768KHz oscillator keeps running and only the RTC RAM retains the state. SRAM, CPUs and I/Os are all in OFF state, as there is no 1.8V and no VDDIO being supplied to the GS1011 device. I/O pins (except alarms) should not be driven high by an external device during standby state due to diodes in the internal ESD protection circuitry. GAINSPAN CONFIDENTIAL PAGE 17 OF 50 GS1500M DATA SHEET Driving I/O pins high during standby could result in incorrect operation on exit from standby state. This is the lowest-power-consumption state. In a typical application, the system returns to the Standby state between periods of activity, to keep the average power very low and enable years of operation using conventional batteries. During standby, the RTC isolates itself from the rest of the chip, since the signals from the rest of the chip are invalid. This prevents corruption of the RTC registers. Exit from standby occurs when a pre-specified wakeup time occurs, or when one of the two alarm pins sees the programmed polarity of signal edge. When one of the wakeup conditions occurs, the RTC asserts reset to the chip and sets the DC_DC_CNTL pin high to enable power to the rest of the module. After 3mS, the power to the rest of the module is assumed to be good, the isolation between the RTC and the rest of the chip is released, and the EXT_RESETn pin is released. The WLAN CPU now runs at 32KHz for another 10mS until the 44MHz oscillator is stable, at which time it switches over to running at 22MHz. Another ~900mS are required to initialize the application software. Note that the alarm pins are strictly edge detected, and cannot be read like GPIO pins. If it is necessary to read the DC level of an alarm input, the signal must be connected to a GPIO pin thru an over-voltage tolerant buffer, powered from VDDIO, so that it stops driving the GPIO pin when VDDIO is turned off in standby mode. Note: During first battery plug, i.e. when power is applied the first time to the RTC power rail (VBAT), the power detection circuit in the RTC also causes a wakeup request. The RTC startup up latency will be at least a couple of hundred ms (and may be as much as 3 seconds) as it is waiting for stabilization of the 32KHz crystal. After the oscillator startup delay, at first battery plug, there is a 7.8mS delay for power to be assumed good and a 31.25mS delay for 44MHz oscillator startup. These delays are reduced for subsequent startups by the first battery plug software. Again, ~900mS are required to initialize the application software. System Configuration: When a power-up is requested, the system transitions from the Standby state to the System Configuration state. In this state, the WLAN CPU is released from reset by the RTC. The APP CPU remains in the reset state during System Configuration. The WLAN CPU then executes the required system configurations, releases the APP CPU from reset, and transitions to the Power-ON state. The System Configuration state is also entered on transition from the Power-ON state to the Standby state, to complete necessary preparations before shutting off the power to the core system. Finally, the System Configuration state is used for firmware updates. Power-ON: This is the active state where all system components can be running. The Power-ON state has various sub-states, in which unused parts of the system can be in sleep mode, reducing power consumption. Sleep states are implemented by gating the clock signal off for a specific system component. Sleep: In the Sleep state, the 44MHz crystal remains running, but it is gated off to one or both CPUs. Each CPU can independently control its own entry into Sleep state. Any enabled interrupt will cause the interrupted CPU to exit from Sleep state, and this will occur within a few clock cycles. Deep Sleep: Deep sleep is entered only when both CPUs agree that the wakeup latency is OK. In Deep Sleep mode, the 44MHz crystal oscillator is turned off to save power, but all power supplies remain turned on. Thus all registers, memory, and I/O pins retain their state. Any enabled interrupt will cause an exit from Deep Sleep state, but this now requires startup of the 44MHz oscillator, which requires 10mS. GAINSPAN CONFIDENTIAL PAGE 18 OF 50 GS1500M DATA SHEET The following are not system states, but are related design notes: Power Control: The GS1500M was designed with the intent that power to the non-RTC portions of the chip be controlled from the DC_DC_CNTL signal. In applications where it is preferred that an external host control the power, this is OK if ALL power, including VBAT power, is turned on and off by the external host. In this case, all state is lost when power goes off, and the latencies from first battery plug apply. If these latencies are not acceptable, then the GS1500M MUST control power. The external host would use an alarm to wake it up, and a serial command to put it into standby. And the DC_DC_CNTL pin would control the power supplies. It is NOT reliable for the external host to directly control the power supplies if VBAT is to be left turned on. This is because the RTC would not know when to isolate itself from the rest of the chip, and might get corrupted during power up or power down. EXT_RESETn pin: If the external host is driving the EXT_RESETn pin, it MUST do so with an open drain driver. This is because this pin also must be able to be driven low by the RTC and by the voltage monitor chip on the GS module. In addition, if an external host is connected to the EXT_RESETn pin, there must be an external 10K ohm pull-up resistor on the board, pulling up to VDDIO. This is needed to overcome a possible pull-down in the host at first power application. It is also recommended that the host not actively assert EXT_RESETn until all the startup latencies have expired. One possible usage of the EXT_RESETn pin by an external host is to monitor the pin as an input to detect when the 32KHz oscillator has started up after first application of VBAT power. When the EXT_RESETn pin goes high, the oscillator has started. Under most conditions, this will be considerably faster than the 3 second worst case. It should also be noted that the constraint that I/O pins not be driven high during standby also applies to the EXT_RESETn pin. It should be pulled only to VDDIO, which shuts off in standby mode. For more information, consult the GS1011 Peripheral and Register Description [2] and GS1011 SoC data sheet [3] for detailed descriptions. GAINSPAN CONFIDENTIAL PAGE 19 OF 50 GS1500M DATA SHEET 3 Pin-out and Signal Description 3.1 GS1500M Device Pin-out Diagram (Module top view) Figure 3-1: GS1500M Device Pin-out Diagram (Module top view) GAINSPAN CONFIDENTIAL PAGE 20 OF 50 GS1500M DATA SHEET 3.1.1 GS1500M Module Pins Description PINS 3 4 5 6 7 8 9 10 11 12 14 15 16 18 19 20 21 22 NAME VOLTAGE INTERNAL BI- SIGNAL DESCRIPTION GND 0V Not Applicable Analog port Ground JTAG_TCK VDDIO Pull-up (See Note 1) Digital Input Joint Test Action Group Test Clock JTAG_TDO VDDIO Not Applicable Digital Output Joint Test Action Group Test Data Out JTAG_TDI VDDIO Pull-up (See Note 1) Digital Input Joint Test Action Group Test Data In JTAG_TMS VDDIO Pull-up (See Note 1) Digital Input Joint Test Action Group Test Mode Select JTAG_nTRST VDDIO Pull-up (See Note 1) Digital Input Joint Test Action Group Test Mode Reset Active Low ALARM1 VBAT Pull-down (See Note 1) RTC Input Embedded Real Time Clock Wake Up Input 1 RTC_OUT1 VBAT Not Applicable RTC Output Embedded Real Time Clock Wake Up Output 1 VBAT VBAT Not Applicable Analog port Embedded Real Time Clock Power Supply DC_DC_CNTL VBAT Not Applicable Digital Output VIN_3V3 Regulator Control Output ADC1 VDD18 Not Applicable Analog Input General Analog to Digital Converter 1 Not Applicable Analog Input General Analog to Digital Converter 2 (internal) ADC2 VDD18 (internal) ALARM2 VBAT Pull-down (See Note 1) RTC Input Embedded Real Time Clock Wake Up Input 2 MSPI_DIN / GPIO6 VDDIO Pull-down Digital Input / Output Master Serial Peripheral Interface Bus Data Input / General Purpose Input Output MSPI_DOUT / GPIO7 VDDIO Pull-down Digital Input / Output Master Serial Peripheral Interface Bus Data Output / General Purpose Input Output VOUT_1V8 VIN_3V3 Not Applicable Analog port Internal 1.8V Vout (internally regulated) GND 0V Not Applicable Analog port Ground MSPI_CLK / GPIO5 VDDIO Pull-down Digital Input / Output Master Serial Peripheral Interface Bus Clock / General Purpose Input Output MSPI_CS0 / GPIO4 VDDIO Pull-down Digital Input / Output Master Serial Peripheral Interface Bus Chip Select 0 / General Purpose Input Output MSPI_CS1 / GPIO13 VDDIO Pull-down Digital Input / Output Master Serial Peripheral Interface Bus Chip Select 1 / General Purpose Input Output GPO21_11MHZ VDDIO Pull-down Digital Input / Output Internal Clock Circuitry Test Point / General Purpose Input Output GPO20_22MHZ VDDIO Pull-down Digital Input / Output Internal Clock Circuitry Test Point / General Purpose Input Output GAINSPAN CONFIDENTIAL PAGE 21 OF 50 GS1500M DATA SHEET PINS 23 24 25 26 28 29 30 31 32 33 34 35 36 37 38 39 40 41 NAME VOLTAGE INTERNAL BI- SIGNAL DESCRIPTION GPO19_44MHZ VDDIO Pull-down Digital Input / Output Internal Clock Circuitry Test Point / General Purpose Input Output PWM0 / GPIO10 VDDIO Pull-down Digital Input / Output Pulse Width Modulator / General Purpose Input Output I2C_CLK/GPIO9 VDDIO Pull-down (NOTE 4) Digital Input / Output Inter-Integrated Circuit Clock / General Purpose Input Output I2C_DATA/GPIO8 VDDIO Pull-down (NOTE 4) Digital Input / Output Inter-Integrated Circuit Data / General Purpose Input Output SSPI_DOUT VDDIO Pull-up (See Note 1) Digital Output SSPI_CLK VDDIO Pull-up (See Note 1) Digital Input SSPI_CS VDDIO Pull-up (See Note 1) Digital Input SSPI_DIN VDDIO Pull-down (See Note 1) Digital Input SPI Slave Transmit Data Output to the HOST SPI Slave Clock Input from the HOST SPI Slave Chip Select Input from the HOST SPI Slave Receive Data Input from the HOST VIN_3V3 VIN_3V3 Not Applicable Analog port Single Supply Port GND 0V Not Applicable Analog port Ground EN_1V8 VDDIO Need to be driven HIGH or LOW externally Digital Input Internal 1.8V regulator enable port-Active High VDDIO VDDIO Not Applicable Analog port All I/O voltage domain (can be tied to VIN_3V3 or tied to HOST I/O supply) UART1_CTS / GPIO26 VDDIO Pull-down Digital Input / Output Universal Asynchronous Receiver Transmitter 1 Clear to Send Input (See Note 6) / General Purpose Input Output UART1_RTS / GPIO27 VDDIO Pull-down Digital Inut / Output Universal Asynchronous Receiver Transmitter 1 Request to Send Output (See Note 6) / General Purpose Input Output UART1_RX / GPIO3 VDDIO Pull-down Digital Input / Output Universal Asynchronous Receiver Transmitter 1 Receive Input / General Purpose Input Output VDDIO Pull-down Digital Input/ Output Universal Asynchronous Receiver Transmitter 1 Transmitter Output / General Purpose Input Output UART0_TX / GPIO1 VDDIO Pull-down Digital Input / Output Universal Asynchronous Receiver Transmitter 0 Transmitter Output / General Purpose Input Output UART0_RTS / GPIO25 VDDIO Pull-down Digital Input / Output Universal Asynchronous Receiver Transmitter 0 Request to Send Output (See Note 6) / General Purpose Input Output UART0_RX / GPIO0 VDDIO Pull-down Digital Input / Output Universal Asynchronous Receiver Transmitter 0 Receive Input / General Purpose Input Output (See Note 2) UART1_TX/ GPIO2 GAINSPAN CONFIDENTIAL PAGE 22 OF 50 GS1500M DATA SHEET PINS NAME 42 43 44 45 VOLTAGE INTERNAL VDDIO Pull-down Digital Input / Output Universal Asynchronous Receiver Transmitter 0 Clear to Send Input (See Note 6) / General Purpose Input Output GPO31_LED2 VDDIO Pull-down Digital Input / Output Light Emitting Diode Driver / General Purpose Input Output GPIO30_LED1 VDDIO Pull-down Digital Input / Output Light Emitting Diode Driver / General Purpose Input Output GPIO29 VDDIO Pull-down Digital Input / Output General Purpose Input Output Digital Input / Output General Purpose Input Output Digital Open Drain Module Hardware Reset Input and Power Supply Reset Monitor Indictor Input / Out- Active Low Analog port Ground GPIO28 VDDIO Pull-down (See Note 3) EXT_RESETn 47 VDDIO Pull-up (See Note 5) GND 48 DESCRIPTION UART0_CTS / GPIO24 (See Note 3) 46 SIGNAL 0V Not Applicable Table 3-1: Signal Description Notes: 1. These pins have onboard hardware configured pull-ups/downs and cannot be changed by software. 2. If UART1_RTS (GPIO27) is high during reset or power on, then the GS1500M will wait for Flash download via UART0 or SSPI interface. Route this pin on the base board so it can be pulled up to VDDIO for programming the module. 3. GPIO 28 and 29 are sampled at reset to establish JTAG configuration for debugging. These signals should not be driven from an external device. If using JTAG, configure these pins as outputs. 4. If I C interface is used, provide 2K Ohm pull-ups, to VDDIO, for pins 25 and 26 (I2C_CLK and I2C_DATA) 5. EXT_RESETn is an active low signal. It is an output during power up, indicating to the system when GS1500M is out of power-on-reset. After power-on-reset, this pin is an input. It is not necessary to assert reset to the GS1500M after power on, since the GS1500M has a built-in power on reset. Also, the EXT_RESETn signal does not clear the RTC RAM or the SRAM. 6. CTS and RTS signals indicate it is clear to send or ready to send when they are LOW. If signals are high, indicates device is not ready. 7. The WLAN CPU controls the MSPI interface and its driver supports an external Flash Memory device only (compatible with Numonyx M25P80 device). The MSPI interface cannot be controlled directly by the APP CPU and hence the MSPI interface cannot be used for general purpose SPI devices. 2 GAINSPAN CONFIDENTIAL PAGE 23 OF 50 GS1500M DATA SHEET 3.1.2 Example Module Pin Connections Figure 3-2: Module pin connection diagram Note 1) For the noted pin configurations, please refer to data sheet power supply section. Note 2) If I2C interface is used, provide 2KOhm pull-ups, to VDDIO, for pins 25 and 26 (I2C_CLK and I2C_DATA). If not used, leave pins 25 and 26 as No Connects. Note 3) Connect to external HOST SPI (can be left as No Connects if not used). Note 4) Connect to external serial HOST UART (can be left as No Connections if not used) Note 5) This switch enables the programming of GS1500M onboard flash. Switch is recommended for development purposes. For production it is recommended designers provide option to pull this pin (GPIO27) high during reset or power-on for in-circuit programming of the module. . Note 6) The need for external flash memory depends on advanced firmware features selected/required such as factory backup, a more robust over-the-air firmware update and Wi-Fi direct. The serial flash memory should be instruction set compliant with Numonyx M25P80. GAINSPAN CONFIDENTIAL PAGE 24 OF 50 GS1500M DATA SHEET 3.2 Power Supply Connections In this section, diagrams are shown for various application power supply connection. Figure 3-3 : GS1500M Always ON Power Supply Connection Notes: 1) This connection applies generally for designs that target to keep system power on always and use 3.3V I/O 2) Always On is obtained by tying EN_1V8 high which is the enable for the 1.8V voltage regulator. 3) In this state system can still go to deep sleep state and take advantage of low power consumption, but system will not go into the lowest power consumption state (i.e. standby state). GAINSPAN CONFIDENTIAL PAGE 25 OF 50 GS1500M DATA SHEET Figure 3-4 : GS1500M with 3.3V IO and Standby Support Applications that require Standby Mode and use GS1500M MUST use this connection configuration to take advantage of the lowest power consumption during standby mode. In this connection it is important to note the following: 1) GS1500M is supplied with VIN_3V3 and supports the in-rush current for RF transmission; thus, the 3.3V DC/DC Regulator may have to be an Up/Down regulator depending on if a is battery used For GS1500M VDDIO and VIN_3V3, power MUST be shut OFF in standby mode so there is no leakage and thus achieve the lowest current consumption. GAINSPAN CONFIDENTIAL PAGE 26 OF 50 GS1500M DATA SHEET 4 Electrical Characteristics 4.1 Absolute Maximum Ratings Conditions beyond those cited in Table 4-1 may cause permanent damage to the GS1500M, and must be avoided. Sustained operation beyond the normal operating conditions my affect long term reliability of the module. Parameter Storage temperature RTC Power Supply I/O Supply voltage Single Supply Port Symbol TST Vbat VDDIO VIN_3V3 Minimum -55 -0.5 -0.5 -0.5 Typical 3.3 Maximum +125 4.0 4.0 4.0 Unit ºC V V V Table 4-1: Absolute Maximum Ratings NOTE: For limitations on state voltage ranges, please consult section 2.6.1. 4.2 Operating Conditions Parameter Extended temp. range RTC Power Supply I/O Supply voltage Single Supply Port GS1500M Symbol TA Vbat VDDIO Minimum -40 1.6 3.0 Typical 3.3 3.3 Maximum +85 3.6 3.6 Unit ºC V V VIN_3V3 3.14 3.3 3.46 V Table 4-2: Operating Conditions 4.3 Internal 1.8V regulator VIN_3V3=VDDIO=Vbat=3.3V Temp=25ºC fOSC=3.0MHz Parameter Symbol Output Voltage Maximum Output Current Oscillation Frequency 1.8V Regulator Enable "H" Voltage 1.8V Regulator Enable "L" Voltage Test conditions Minimum Typical 1.8 30 Maximum Unit V mA MHz VOUT_1V8 IVOUT_1V8 fOSC 1.6 50 3.45 EN_1V8 1.0 VIN_3V3 V EN_1V8 0 0.25 V Table 4-3: Internal 1.8V Regulator GAINSPAN CONFIDENTIAL PAGE 27 OF 50 GS1500M DATA SHEET 4.4 I/O DC Specifications 4.4.1 Digital Input Specifications Parameter Input Low Voltage Symbol VIL Input High Voltage VIH Minimum -0.3 0.8* VDDIO Typical Maximum 0.25* VDDIO Unit V VDDIO V Note Table 4-4: Digital Input Parameters 4.4.2 Digital Output Specification Parameter Output Low Voltage Output High Voltage Output rise time @ VDDIO=3.3V Output fall time @ VDDIO=3.3V Symbol Mininum VOL VOH Typical Maximum Unit Note 0 0.4 V With 4 mA load 2.4V VDDIO V tTLH 7 ns tTHL 7 ns VDDIO=3.0V, DC current load 4.0 mA With 4 mA, 33 pF load With 4 mA, 33 pF load Table 4-5: Digital Output Parameters 4.4.3 I/O Digital Specifications (Tri-State) Parameter Input Low Voltage Input High Voltage Schmitt trig. Low to High threshold point Schmitt trig. High to Low threshold point Input Leakage Current Tri-State Output Leakage Current Pull-Up Resistor Pull-Down Resistor Output Low Voltage Symbol VIL VIH Mininum -0.3 0.8* VDDIO VT+ 1.5 Typical Maximum 0.25* VDDIO Unit V VDDIO V V VT- 1 V IL 5 µA OzL 5 µA Ru 0.05 1 MΩ Rd 0.05 1 MΩ VOL 0 0.4 V GAINSPAN CONFIDENTIAL Note Pull up/down disabled Pull up/down disabled With 4/12/20 mA load PAGE 28 OF 50 GS1500M DATA SHEET Parameter Output High Voltage Output rise time @ VDDIO =3.3V Symbol Mininum VOH 2.4V Output fall time @ VDDIO = 3.3V Input rise time Input fall time Typical Maximum Unit VDDIO V tToLH 7 ns tToHL 7 ns tTiLH tTiHL 7 7 ns ns Note With 4/12/20 mA load With 4/12/20 mA load, 33 pF With 4/12/20 mA load, 33 pF Table 4-6: I/O Digital Parameters 4.4.4 RTC Input Specifications (with Schmitt Trigger) Parameter I/O Supply Voltage Input Low Voltage Input High Voltage Schmitt trig. Low to High threshold point Schmitt trig. High to Low threshold point Input Leakage Current Symbol VDDRTC VIL VIH Mininum 1.2 -0.3 0.8*VDDRTC VT+ VT- Maximum Vbat 0.25*VDDRTC VDDRTC Unit V V V 0.57*VDDRTC 0.68*VDDRTC V 0.27*VDDRTC 0.35*VDDRTC V IL Typical 260 Note pA Table 4-7: RTC Input Parameters 4.4.5 RTC Output Specifications Parameter I/O Supply Voltage Output Low Voltage Output High Voltage Output rise time Output fall time Input Leakage Current Symbol VDDRTC VOL VOH tTLH tTHL IL Mininum 1.2 0 0.8*VDDRTC 19 21 Typical Maximum Vbat 0.4 VDDRTC 142 195 730 Unit V V V ns ns pA Table 4-8: RTC Output Parameters GAINSPAN CONFIDENTIAL PAGE 29 OF 50 Note 50 pF load 50 pF load GS1500M DATA SHEET 4.5 Power Consumption Test Conditions: VDD33=VDDIO=Vbat=3.3V Temp=25ºC System State Deep Sleep Standby Sleep PS poll, DTIM=1 TX @ 802.11b TX @ 802.11g/n Receive Current (Typ.) 1.3mA 7uA 8mA 3.6mA 245mA 200mA 65mA Table 4-9: Power Consumption in Different States 4.6 Radio Parameters Test Conditions: VIN_3V3=VDDIO=Vbat=3.3V Temp=25ºC Parameter RF Frequency range Radio bit rate Minimum 2412 Typical 1 Maximum 2497 HT20 MCS7 Unit MHz Notes Mbps Transmit/Recieve specification for GS1500M 13 14 13 12 12 11 Output power (average) Spectrum Mask F0 +/- 11 MHz Offset >= 22 MHz Receive Sensitivity at antenna port -30 -50 -96 -88 -91 -75 -92 -72 dBm 11b, 1, Mbps, BPSK/DSSS 11b, 11 Mbps, CCK/DSSS 11g, 6 Mbps, BPSK/OFDM 11g, 54 Mbps, 64-QAM/OFDM 11n, MCS 0 (6.5 Mbps), BPSK/OFDM 11n, MCS 7 (65 Mbps), 64-QAM/OFDM dBr Modulated signal at antenna port dBm 11b, 1, Mbps, BPSK/DSSS 11b, 11 Mbps, CCK/DSSS 11g, 6 Mbps, BPSK/OFDM 11g, 54 Mbps, 64-QAM/OFDM 11n, MCS 0 (6.5 Mbps), BPSK/OFDM 11n, MCS 7 (65 Mbps), 64-QAM/OFDM Table 4-10: Radio Parameters GAINSPAN CONFIDENTIAL PAGE 30 OF 50 GS1500M DATA SHEET 4.7 ADC Parameters Test Conditions: VIN_3V3=VDDIO=Vbat=3.3V Temp=25ºC Parameter ADC Resolution ADC Sample Freq ADC input Clock Freq Minimum 1.024 Typical 10 - Maximum 31.25 Unit Bits ksps 32.768 - 1000 kHz ADC Full Scale Voltage VOUT_1V8 – 0.036 V 32 Clocks Conversion Time ADC Integral Non-Linearity (INL) -2.0 - 2.0 LSB ADC Differential non-linearity (DNL) -1.0 - 1.0 LSB - 400 800 µA ADC Offset Error -10 - 10 mV ADC Gain Error -10 - 10 mV - 1 µS AVDD Power Supply current (operational) Settling Time Input resistance 1 - - MOhm Input Capacitance - 10 - pF 1.179 1.24 1.301 V Bandgap Output Voltage (Vref) (T = 25 ºC) Notes Reference = VOUT_1V8 Based on internally generated 1MHz or 32.768 KHz Clocks Table 4-11: ADC Parameters GAINSPAN CONFIDENTIAL PAGE 31 OF 50 GS1500M DATA SHEET 4.8 SPI Interface Timing Test Conditions: VIN_3V3=VDDIO=Vbat=3.3V Temp=25ºC 4.8.1 Motorola SPI, clock polarity SPO = 0, clock phase SPH = 0 Figure 4-1: timing diagram, Master mode, SPO=SPH=0. Parameter tSSetup tTxdDelay tRxdSetup tRxdHold tSSHold Description Minimum Minimum time between falling edge of Select line and first rising edge of SPI clock 1 mixed 30 nsec 10 nsec 1 MSPI clock period Table 4-12: timing parameters, Master mode, SPO=SPH=0. GAINSPAN CONFIDENTIAL Unit MSPI clock period 2 core SPI clock periods + 3 nsec Delay in Master asserting TX line after falling edge of Select line Time before rising edge of SPI clock by which received data must be ready Time for which received data must be stable after rising edge of SPI clock Time for which the Select line will be held after the sampling edge for the final bit to be transferred Maximum PAGE 32 OF 50 GS1500M DATA SHEET Figure 4-2: timing diagram, Slave mode, SPO=SPH=0. Parameter tSSetup tTxdDelay tRxdSetup Description Minimum Minimum time between falling edge of Select line and first rising edge of SPI clock. 4 core SPI clock periods + 68 ns Delay in Slave asserting TX line after falling edge of SPI clock, or the first bit after falling edge of the Select line. Time before rising edge of SPI clock by which received data must be ready tRxdHold Time for which received data must be stable after rising edge of SPI clock tSSHold Time for which the Select line will be held after the sampling edge for the final bit to be transferred Maximum mixed 4 core SPI clock periods + 68 ns 15 3 core SPI clock periods + 14 ns 3 core SPI clock periods + 14 ns Table 4-13: timing parameters, Slave mode, SPO=SPH=0. GAINSPAN CONFIDENTIAL Unit PAGE 33 OF 50 mixed ns mixed mixed GS1500M DATA SHEET 4.8.2 Motorola SPI, clock polarity SPO = 0, clock phase SPH = 1 Figure 4-3: timing diagram, Master, SPO=0, SPH=1. Parameter tSSetup tTxdDelay tRxdSetup tRxdHold tSSHold Description Minimum time between falling edge of select line and first rising edge of SPI clock. Delay in Master asserting TX line after rising edge of SPI clock. Time before falling edge of SPI clock by which received data must be ready. Time for which received data must be stable after falling edge of SPI clock. Time for which the Select line will be held low after the sampling edge for the final bit to be transferred. Minimum Maximum MSPI clock period 1.5 0 ns 30 ns 10 ns 0.5 MSPI clock period Table 4-14: timing parameters, Master mode; SPO=0, SPH=1. GAINSPAN CONFIDENTIAL Unit PAGE 34 OF 50 GS1500M DATA SHEET Figure 4-4: timing diagram, Slave, SPO=0, SPH=1. Parameter Description tSSetup Minimum time between falling edge of select line and first rising edge of SPI clock. tTxdDelay Delay in Slave asserting TX line after rising edge of SPI clock. tRxdSetup Time before falling edge of SPI clock by which received data must be ready. tRxdHold Time for which received data must be stable after falling edge of SPI clock. tSSHold Time for which the Select line will be held low after the sampling edge for the final bit to be transferred. Minimum Maximum 15 ns 4 core SPI clock periods + 68 ns 15 mixed ns 3 core SPI clock periods + 14 ns 3 core SPI clock periods + 14 ns Table 4-15: timing parameters, Slave mode, SPO=0, SPH=1. GAINSPAN CONFIDENTIAL Unit PAGE 35 OF 50 mixed mixed GS1500M DATA SHEET 4.8.3 Motorola SPI, clock polarity SPO = 1, clock phase SPH = 0 Figure 4-5: timing diagram, Master mode, SPO=1, SPH=0. Parameter Description Minimum tSSetup Minimum time between falling edge of select line and first falling edge of SPI clock. 1 tTxdDelay Delay in Master asserting TX line after falling edge of Select line. tRxdSetup tRxdHold tSSHold Time before falling edge of SPI clock by which received data must be ready. Time for which received data must be stable after falling edge of SPI clock. Time for which the Select line will be held low after the sampling edge for the final bit to be transferred. Maximum MSPI clock period 2 core SPI clock periods + 3 ns mixed 30 ns 10 ns 1 MSPI clock period Table 4-16: timing parameters, Master mode, SPO=1, SPH=0. GAINSPAN CONFIDENTIAL Unit PAGE 36 OF 50 GS1500M DATA SHEET Figure 4-6: timing diagram, Slave mode, SPO=1, SPH=0. Parameter tSSetup tTxdDelay tRxdSetup Description Minimum Minimum time between falling edge of Select line and first falling edge of SPI clock. 4 core SPI clock periods + 68 ns Delay in Slave asserting TX line after rising edge of SPI clock, or the first bit after falling edge of the Select line. Time before falling edge of SPI clock by which received data must be ready. tRxdHold Time for which received data must be stable after falling edge of SPI clock. tSSHold Time for which the Select line will be held low after the sampling edge for the final bit to be transferred. Maximum Mixed 4 core SPI clock periods + 68 ns 15 Mixed ns 3 core SPI clock periods + 14 ns 3 core SPI clock periods + 14 ns Table 4-17: timing parameters, Slave mode, SPO=1, SPH=0. GAINSPAN CONFIDENTIAL Unit PAGE 37 OF 50 Mixed MSPI clock period GS1500M DATA SHEET 4.8.4 Motorola SPI, clock polarity SPO = 1, clock phase SPH = 1 Figure 4-7: timing diagram, Master mode, SPO=SPH=1. Parameter tSSetup tTxdDelay tRxdSetup tRxdHold tSSHold Description Minimum time between falling edge of select line and first falling edge of SPI clock. Delay in Master asserting TX line after falling edge of SPI clock. Time before rising edge of SPI clock by which received data must be ready. Time for which received data must be stable after rising edge of SPI clock. Time for which the Select line will be held low after the sampling edge for the final bit to be transferred. Minimum Maximum MSPI clock period 1.5 0 ns 30 ns 10 ns 0.5 MSPI clock period Table 4-18: timing parameters, Master mode, SPO=SPH=1. GAINSPAN CONFIDENTIAL Unit PAGE 38 OF 50 GS1500M DATA SHEET Figure 4-8: timing diagram, Slave mode, SPO=SPH=1. Parameter Description Minimum tSSetup Minimum time between falling edge of select line and first falling edge of SPI clock. 15 tTxdDelay Delay in Slave asserting TX line after falling edge of SPI clock. tRxdSetup Time before rising edge of SPI clock by which received data must be ready. tRxdHold Time for which received data must be stable after rising edge of SPI clock. tSSHold Time for which the Select line will be held low after the sampling edge for the final bit to be transferred. Maximum ns 4 core SPI clock periods + 68 ns 15 Mixed ns 3 core SPI clock periods + 14 ns 3 core SPI clock periods + 14 ns Table 4-19: timing parameters, Master mode, SPO=SPH=1. GAINSPAN CONFIDENTIAL Unit PAGE 39 OF 50 Mixed Mixed GS1500M DATA SHEET 5 Package and Layout Guidelines 5.1 GS1500M Recommended PCB Footprint and Dimensions Figure 5-1: GS1500M Module Recommended PCB Footprint (dimensions are in inches) GAINSPAN CONFIDENTIAL PAGE 40 OF 50 GS1500M DATA SHEET Figure 5-2: GS1500M Module Dimensions (in inches) Notes: 1. All Dimensions are in inches. Tolerances shall be ±0.010 for .xxx and ±0.02 for .xx inches. 2. Absolutely no metal trace or ground layer underneath this area. 3. It is recommended not to run circuit traces underneath the module especially near these holes; The RF shield mounting holes are grounded. If traces must be routed under the GS1500M, it is recommended that extra thick solder mask (5 mils) be used to prevent shorting. High speed signals should be kept as far as possible from the antenna and RF areas of the GS1500M. 4. In performing SMT or manual soldering of the module to the base board, first align the row of pins from #18 thru 31 onto the base board and then match the other two rows. In addition to the guidelines in Figure 5-1, note the following suggestions: • External Bypass capacitors for all module supplies should be as close as possible to the module pins. • Never place the antenna very close to metallic objects If the PCB Antenna is to be used: • For best RF performance, it is recommended that the PCB antenna hang over the edge of the base board, so that there is no FR4 under it or next to it. • The PCB antenna keep out area, as shown in Figure 5-1, must be adhered to. Ground plane on the base board should be kept further away if possible, and should not fully enclose the PCB antenna. • In addition it is recommended to have clearance above and below the PCB trace antenna (Figure 5-3) for optimal range performance. • Do not use a metallic or metalized plastic for the end product enclosure. GAINSPAN CONFIDENTIAL PAGE 41 OF 50 GS1500M DATA SHEET • Recommendation is to keep plastic enclosure clearance of 1cm from top and bottom of the GS1500M PCB antenna keep-out area, if possible. 5-mm (0.2 in) clearance shall be the minimum as shown in Figure 5-3. Figure 5-3 Recommended clearance above and below the GS1500M trace antenna 5.1.1 Surface Mount Assembly The reflow profile1 is shown in Figure 5-3. Recommended reflow parameters are summarized in Table 5-1. Figure 5-3: Reflow temperature profile. C2 C1 PreHeat 2 Temperature Ramp up rate for (A) 1.5~3.5 °C/s Pre-heat time (B)3 Pre-heat starting temperature (C1) Pre-heat ending temperature (C2) 80 to 130 seconds 125 to 135 ° C 180 to 200 ° C 5 Heating Peak Temperature range (D) 4 Melting time that is the time over 220 °C (E) Cool Down Ramp (F) 240 to 250 °C 50 to 75 seconds >2 °C/s Table 5-1: Recommended reflow parameters. GAINSPAN CONFIDENTIAL PAGE 42 OF 50 GS1500M DATA SHEET Note: 1. Perform adequate test in advance as the reflow temperature profile will vary accordingly to the conditions of the parts and boards, and the specifications of the reflow furnace. 2. Max number of reflows supported are two. 3. Temperature uniformity inside the IR reflow oven must be tightly controlled and multiple thermocouples should be used. An example of possible thermocouple locations is given in Figure 5-4. The locations should also include multiple points INSIDE the module RF shield (e.g., TC1, TC5, and TC7 in Figure 5-4). The temperature profile of ALL thermocouples must meet the requirements of Table 5-1. 4. Pay close attention to “Melting Time over 220oC”. Sufficient time is necessary to completely melt all solder. 5. Be careful about rapid temperature rise in preheat zone as it may cause excessive slumping of the solder paste. 6. If the preheat is insufficient, rather large solder balls tend to be generated. Conversely, if performed excessively, fine balls and large balls will generate in clusters at a time. 7. If the temperature is too low, non-melting tends to be caused in the area with large heat capacity after reflow. 8. Be careful about sudden rise in temperature as it may worsen the slump of solder paste. 9. Be careful about slow cooling as it may cause the positional shift of parts and decline in joining strength at times. 10. A no clean flux should be used during SMT process. GAINSPAN CONFIDENTIAL PAGE 43 OF 50 GS1500M DATA SHEET Figure 5-4: Thermocouple Locations GAINSPAN CONFIDENTIAL PAGE 44 OF 50 GS1500M DATA SHEET Note: The modules are shipped in sealed trays with the following conditions: 250 GAINSPAN CONFIDENTIAL PAGE 45 OF 50 GS1500M DATA SHEET 6 Ordering Information DEVICE DESCRIPTION ORDERING NUMBER Rev Low power module using PCB antenna GS1500M Rev 2.0 Low power module using PCB antenna GS1500M Rev 2.21 1 Rev 2.2 uses B0 version of the GS1011 SoC Note: Modules ship with only test code. Designers must first program the modules with a released firmware version. Designers should bring out GPIO27 pin (option to pull this pin to VDDIO during reset or power-on) and UART0 or SSPI pins to enable programming of firmware into the module. For details refer to the Programming GainSpan Modules document. GAINSPAN CONFIDENTIAL PAGE 46 OF 50 GS1500M DATA SHEET 7 Regulatory Notes Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: To assure continued compliance, (example - use only shielded interface cables when connecting to computer or peripheral devices). Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE: FCC & IC Radiation Exposure Statement: This equipment complies with FCC & IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). IMPORTANT NOTE: In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the FCC & IC authorizations are no longer considered valid and the FCC & IC IDs cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining separate FCC & IC authorizations. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users (for example access points, routers, wireless ADSL modems, and similar equipment). The final end product must be labeled in a visible area with the corresponding FCC ID number. GAINSPAN CONFIDENTIAL PAGE 47 OF 50 GS1500M DATA SHEET IC Certification — Canada The labeling requirements for Industry Canada are similar to those of the FCC. A visible label on the outside of the final product must display the IC labeling. The user is responsible for the end product to comply with IC ICES-003 (Unintentional radiators) Manual Information That Must be Included The user’s manual for end users must include the following in-formation in a prominent location. IMPORTANT NOTE: To comply with FCC & IC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. Other notes: GainSpan modules have been built or under development for near body exposure applications. The 20cm statement is a standard note because absorption rate testing (commonly known as SAR or Specific absorption rate) is not modularly transferable for FCC/IC. Thus, if a radio is being used against the body, the end user is still responsible to test for regulatory near body exposure testing (for USA, please refer to the following): • FCC Part 1.1037 • FCC Part 2.1091 Mobile Devices • FCC Part 2.1093 Portable Devices • FCC Part 15.247 (b) (4) GAINSPAN CONFIDENTIAL PAGE 48 OF 50 GS1500M DATA SHEET 8 Limitations THIS DEVICE AND ASSOCIATED SOFTWARE ARE NOT DESIGNED, MANUFACTURED OR INTENDED FOR USE OR RESALE FOR THE OPERATION OF APPLICATION IN A HAZARDOUS ENVIRONMENT, OR REQUIRING FAIL-SAFE PERFORMANCE, OR IN WHICH THE FAILURE OF PRODUCTS COULD LEAD DIRECTLY TO DEATH, PERSONAL INJURY, OR SEVERE PHYSICAL OR ENVIRONMENTAL DAMAGE (COLLECTIVELY, "HIGH RISK APPLICATIONS"). YOU AGREE AND ACKNOWLEDGE THAT YOU HAVE NO LICENSE TO, AND SHALL NOT (AND SHALL NOT ALLOW A THIRD PARTY TO) USE THE TECHNOLOGY IN ANY HIGH RISK APPLICATIONS, AND LICENSOR SPECIFICALLY DISCLAIMS ANY WARRANTY REGARDING, AND ANY LIABILITY ARISING OUT OF, HIGH RISK APPLICATIONS. GAINSPAN CONFIDENTIAL PAGE 49 OF 50 GS1500M DATA SHEET 9 References [1] Title Reference Version Source Wireless LAN Medium Access Control (MAC) and Physical Layer (PHY) Specifications IEEE Standard 802.11-2007 June 12, 2007 Date IEEE [2] Title Reference Version Source GS1011 Peripheral and Register Description GS1011-PRD 1.0 Date GainSpan [3] Title Reference Version Source GS1011 ULTRA LOW-POWER WIRELESS SYSTEM-ON-CHIP DATA SHEET GS1011-DS 1.0 November 9, 2009 Date GainSpan GAINSPAN CONFIDENTIAL November 11, 2009 PAGE 50 OF 50