Evaluation Board User Guide
UG-280
One Technology Way • P.O. Box 9106 • Norwood, MA 02062-9106, U.S.A. • Tel: 781.329.4700 • Fax: 781.461.3113 • www.analog.com
Evaluation Board for the AD7191 Pin-Programmable, 24-Bit Σ-Δ ADC
FEATURES
GENERAL DESCRIPTION
Full-featured evaluation board for the AD7191
Standalone interface using microcontroller and LCD display
PC software for control of AD7191 using USB interface
Various linking options
The AD7191 evaluation kit is a powerful tool for exploring and
evaluating the AD7191 features.
INTRODUCTION
The evaluation board can be operated in complete standalone,
battery powered mode. The LCD display is used to display the
conversion data.
This user guide describes the evaluation board for the AD7191,
which is a pin-programmable, ultralow noise, 24-bit sigmadelta (Σ-Δ) ADC. The AD7191 is a complete analog front end
for low frequency measurement applications. It contains two
differential inputs and includes a low noise PGA and a low-side
power switch.
When the board is connected to (and possibly powered from) a
PC via a standard USB interface, the PC software allows the
graphical display of real-time data, logs them into a text file,
allows the user to modify the settings of the AD7191, and
generally helps in understanding the part features and
performance.
Full data on the AD7191 is available in the AD7191 data sheet
available from Analog Devices, Inc., and should be consulted in
conjunction with this user guide when using the evaluation board.
Finally, the board’s flexible interface structure allows it to be
connected in a number of useful configurations. For example,
the digital section of the evaluation board can be used independently as a convenient digital interface for a user’s own
sensor design PCB or module containing the AD7191.
Alternatively, an external microcontroller can be interfaced to
the AD7191 and, thus, the evaluation board can act as a
complete analog front end for creating and debugging software
on the user’s own digital platform.
EVALUATION BOARD CONNECTION DIAGRAM
BATT
EXT
VOLTAGE
REGULATOR
VOLTAGE
REGULATOR
NOISE TEST
CIRCUITRY
ANALOG
INPUTS
PC
AND
LabVIEW™
BASED
SOFTWARE
SPI/USB
INTERFACE
AD7191
MICRO
VOLTAGE
REFERENCE
DRIVERS
REFIN
Figure 1. AD7191 Evaluation Board
PLEASE SEE THE LAST PAGE FOR AN IMPORTANT
WARNING AND LEGAL TERMS AND CONDITIONS.
Rev. 0 | Page 1 of 20
LCD
09880-001
SENSOR
CONNECTOR
UG-280
Evaluation Board User Guide
TABLE OF CONTENTS
Features .............................................................................................. 1
Software Installation .....................................................................6
Introduction ...................................................................................... 1
Evaluation Software Installation .................................................6
General Description ......................................................................... 1
Evaluation Board Installation ......................................................6
Evaluation Board Connection Diagram........................................ 1
Using the Software ........................................................................6
Revision History ............................................................................... 2
Main Window ................................................................................7
Evaluation Board Hardware ............................................................ 3
ADC Setup .....................................................................................8
Power Supplies .............................................................................. 3
Low Noise Quick Test ...................................................................9
Sockets ........................................................................................... 3
WeighScale Demo ...................................................................... 10
Noise Test....................................................................................... 4
User Units Setup......................................................................... 11
Using an Absolute Reference ...................................................... 4
Evaluation Board Schematics and Artwork................................ 12
Connecting the AD7191 to an External Microcontroller....... 4
Ordering Information.................................................................... 16
Using the AD7191 Evaluation Board in Standalone Mode ........ 5
Bill of Materials........................................................................... 16
Using the AD7191 Evaluation Board with the PC Software....... 6
Related Links................................................................................... 17
REVISION HISTORY
6/11—Revision 0: Initial Version
Rev. 0 | Page 2 of 20
Evaluation Board User Guide
UG-280
EVALUATION BOARD HARDWARE
An external power supply can be applied via J10. Place Link J1
in Position EXT.
POWER SUPPLIES
There are several power supply options on the AD7191
evaluation board.
Standalone Operation
Connected to USB Connector
The AD7191 evaluation board is powered via the 5 V supply
from the USB connector, J51. This 5 V supply can be used to
power the AD7191 directly. Link J1 should be placed in the 5 V
USB position.
The 5 V supply from the USB connector can be regulated to
3.3 V using the on-board ADP3303-3.3, a high precision, low
power, 3.3 V output voltage regulator. Therefore, via Link J1, the
3.3 V can be used as the power supply to the AD7191. Link J1
should be placed in the 3.3 V position.
The AD7191 can be powered using a 9 V battery, B1, or using
an external 9 V dc source connected at J31. The 9 V is regulated
down to 5 V using the on-board ADP3303ARZ-5, a high
precision, low power 5 V output regulator. Using Link J1, this
regulated 5 V can be used as the supply to the AD7191. To use
this option, Link J1 should be placed in the 5 V BAT position.
The AD7191 evaluation board can be powered using a 9 V
battery, B1, or using an external 9 V dc source connected at
J31. The 9 V is regulated down to 5 V using the on-board
ADP3303ARZ-5, a high precision, low power 5 V output
regulator. Using Link J1, this regulated 5 V can be used as the
supply to the AD7191. To use this option, place Link J1 in the
5 V BAT position.
An external power supply can be applied via J10. Place Link J1
in Position EXT.
SOCKETS
There are five sockets relevant to the operation of the AD7191
on this evaluation board. The functions of these sockets are
outlined in Table 1.
Table 1. Socket Functions
Socket
REF+
REF−
AIN1
AIN2
MCLK
Description
Subminiature BNC (SMB) connector. This socket is used in conjunction with REF− to apply an external reference to the AD7191.
The voltage for the REFIN(+) input of the AD7191 is applied to this socket.
Subminiature BNC (SMB) connector. This socket is used in conjunction with REF+ to apply an external reference to the AD7191.
The voltage for the REFIN(−) input of the AD7191 is applied to this socket.
Subminiature BNC (SMB) connector. This socket is used to apply an analog input signal to AIN1.
Subminiature BNC (SMB) connector. This socket is used to apply an analog input signal to AIN2.
Subminiature BNC (SMB) connector. An external clock source can be applied to the AD7191 using this socket.
Rev. 0 | Page 3 of 20
UG-280
Evaluation Board User Guide
NOISE TEST
Figure 4 shows the positions of the switches on S6.
OFF
ON
ODR2
ODR1
CLKSEL
VREF
PGA2
PGA1
CHAN
Figure 2. Link Positions for Noise Testing
TEMP
AVDD
S6
AVDD
Figure 4. Switch S6 Positions
REFIN(+)
USING AN ABSOLUTE REFERENCE
1kΩ
As shown in Figure 3, inserting the links in Header J3 connects
a resistor network to the AD7191. The reference to the ADC is
provided by AVDD. The resistor divider generates a bias voltage
of approximately AVDD/2. Channel AIN1 and Channel AIN2 are
connected to this voltage. Thus, conversions can be performed
using this external short to measure the rms noise, peak-to-peak
noise, and peak-to-peak resolution. The ADC is configured
using the DIP switch (S6) on the board. The AD7191 should be
configured as follows:
Output Data Rate = 10 Hz
VREF
J3
09880-005
Figure 3. Noise Test Connections
REF+
AVDD
REFIN(–)
09880-003
100Ω
REF–
1kΩ
AGND
An ADR421 is included on the AD7191 evaluation board so
that the part can also be evaluated using an absolute reference.
The reference can be connected to the REFIN(±) pins of the
AD7191 by connecting the links of Header J3 as shown in
Figure 5.
AD7191
AIN2
AIN2
AIN1
AIN1
09880-004
J3
09880-002
REF+
REF–
AGND
AIN1
AIN2
AVDD
Header J3 allows the user to perform noise testing of the
AD7191. With all links in the vertical position (see Figure 2),
the analog and reference inputs are applied to the AD7191, as
shown in Figure 3.
Figure 5. Connecting an Absolute Reference to the AD7191
CONNECTING THE AD7191 TO AN EXTERNAL
MICROCONTROLLER
The AD7191 evaluation board can be connected to an external
microcontroller using Header J2. With all links in place, the
AD7191 is connected to the on-board microcontroller. However,
with these links removed, the AD7191 is disconnected from
the evaluation board microcontroller. The user can then use a
header to interface the AD7191 to the external microcontroller.
Gain = 128
Channel = AIN1 − AIN2
Rev. 0 | Page 4 of 20
Evaluation Board User Guide
UG-280
USING THE AD7191 EVALUATION BOARD IN STANDALONE MODE
OFF
The AD7191 evaluation board can be operated in standalone
mode. In this mode, the evaluation board functions as a weigh
scale demonstration. Channel AIN3/AIN4 is the analog input
channel. The AIN3 and AIN4 pins, along with REFIN(+),
REFIN(−), AVDD, and AGND, are connected to the J4 header.
This header allows the user to connect a load cell to the AD7191.
The load cell should be connected to the header as shown in
Figure 6. A 6-wire load cell is shown, but a 4-wire load cell can
also be connected.
ODR1
CLKSEL
PGA2
PGA1
CHAN
S6
09880-007
TEMP
EXC+
Figure 7. Switch S6 Positions for Load Cell Connection
SENSE+
The conversions from the AD7191 are displayed on the LCD
display. The four buttons beneath the LCD display allow the
user to calibrate the weigh scale system, adjust the LCD contrast, and read the offset and gain registers. The function of
each button is listed at the bottom of the LCD display.
GND/SHLD
AVDD/EXC
REF1(+)
OUT+
AIN3(+)
AIN4(–)
OUT–
REF1–
GND/SHLD
J4
09880-006
PWR_SW
SENSE–
EXC–
ON
ODR2
Figure 6. Load Cell Connection to Header J4
The AD7191 is configured for an update rate of 10 Hz. The gain
is programmed to 128. Channel AIN3/AIN4 is selected as the
active channel. Figure 7 shows the positions of the switches on S6.
To operate the weigh scale demonstration, connect the load cell
to Header J4, as shown in Figure 6. Apply power to the AD7191
evaluation board using either a 9 V battery or a 9 V DC power
source. Ensure that Link J1 is in the 5 V BAT/EXT position. The
weigh scale demonstration can also be powered from the USB
connector if the board is connected to a PC. Link J1 should be
in the 5 V USB position in this case.
With no weight on the weigh scale, an offset calibration should
be performed (selectable from the buttons below the LCD
display). The expected full-scale weight should then be placed
on the load cell and the full-scale calibration performed. The
user should select the corresponding full-scale weight on the
LCD display because the weigh scale demonstration supports
full-scale weights of 500 g to 10 kg. The software then continuously reads conversions from the AD7191, scales the conversions
appropriately, and displays the resulting weight on the LCD
display.
Rev. 0 | Page 5 of 20
UG-280
Evaluation Board User Guide
USING THE AD7191 EVALUATION BOARD WITH THE PC SOFTWARE
SOFTWARE INSTALLATION
EVALUATION BOARD INSTALLATION
The AD7191 evaluation board software should be installed
before connecting the AD7191 evaluation board to the PC.
1.
EVALUATION SOFTWARE INSTALLATION
2.
3.
Insert the AD7191 evaluation kit CD in the CD-ROM
drive of your PC. The Evaluation software installation
wizard should start automatically after inserting the CD.
If the wizard does not start, navigate to the AD7191
evaluation kit CD on your PC and start the Setup.exe file.
At the prompt, select a destination directory, which is
C:\Program Files\Analog Devices\AD7191 by default.
When the directory is selected, the installation procedure
copies the files into the relevant directories on the hard
drive. The installation program creates a program group
called Analog Devices with the subgroup AD7191 in the
Start menu of the taskbar.
After the installation procedure is complete, double-click
the AD7191 icon to start the program.
2.
USING THE SOFTWARE
Start the AD7191 evaluation software on the PC.
Click on the Windows® Start button, then click All Programs,
Analog Devices, AD7191, and finally AD7191 evaluation
software.
The software allows you to configure the AD7191, gather
samples, and analyze the data. Consult the AD7191 data sheet
for further information on the register bits and their functions.
Figure 8 shows the main window that is displayed when the
program starts. The Main Window section briefly describes
the various menu and button options in the main window.
The data that has been read can be exported to other packages,
such as MathCAD™ or Microsoft® Excel, for further analysis.
09880-008
1.
Connect the AD7191 evaluation board to your PC USB
connector using the USB cable included in the evaluation
kit. The power LED on the evaluation board should turn
on and Found new hardware wizard should start automatically on the PC.
Follow the steps in the wizard until the installation is
completed.
Figure 8. AD7191 Evaluation Software Main Window
Rev. 0 | Page 6 of 20
Evaluation Board User Guide
UG-280
Data
Display Units
MAIN WINDOW
Menu Bar
File
This allows you to write the current set of data to a file for later
use, log data as it is gathered, and exit the program.
Board
This allows you to display the conversions in hexadecimal,
decimal, volts, or user-specified units. If the conversions are
displayed in volts, the value of the reference voltage must be
entered in the Vref box.
Autoscale
This allows you to alter the contrast on the LCD display.
This allows you to enable or disable the autoscale function on
the waveform plot.
Buttons
Delete Data Clear Graphs
X-scale
This allows you to delete the data displayed in the graph.
ADC Reset
This allows you to reset the AD7191 to its default (power-on)
settings.
ADC Setup
This allows you to have a fixed x-axis or a dynamic x-axis.
When the x-axis is fixed, the number of samples to display must
be entered in the X-scale Samples box.
Analysis
Channel
This opens the ADC Setup window, which reflects the current
status of Switch S6.
The data channel to be analyzed is selected using this button.
Low Noise Quick Test
The software can process the conversions as they are being
gathered, or it can process the samples when the ADC has
completed the selected number of conversions.
This allows you to access the noise testing software.
WeighScale Demo
After Sampling
Analyse All Samples
This allows you to access the weigh scale demonstration
software.
This allows you to process all samples gathered. Alternatively, you
can fix the sample size used for analyzing by selecting Analyse
Last # Samples. When Analyse Last # Samples is selected, the
sample size must be entered in the Last # Samples box.
This allows you to change the display units on the graph and
histogram.
Sampling
This allows you to sample continuously or to sample a specific
number of samples. When the Sampling: Capture Defined
Sample Set option is selected, the sample size is entered in the
Samples box.
The software captures all samples generated by the AD7191. If
the software fails to gather all samples, the message shown in
Figure 9 appears.
09880-009
User Units Setup
Figure 9. Error Message When Samples Not Captured
Start Sampling
The software may drop samples for the following reasons:
This allows you to read samples from the AD7191.
•
•
•
Rev. 0 | Page 7 of 20
The data is being analyzed in parallel with the gathering of
samples. You should delay the analysis until the samples
are gathered.
Other programs are running on the PC.
The PC is too slow.
UG-280
Evaluation Board User Guide
ADC SETUP
09880-010
The ADC Setup window reflects the current setup of the
AD7191. The channel, gain, output data rate, and clock source
are selected using the DIP switch, S6. The Setup Pins section
indicates the polarity of the ODR2, ODR1, CLKSEL, PGA1,
PGA2, CHAN, and TEMP pins. The resulting gain, channel,
and clock source are shown in the ADC Setup section. The
value of the voltage reference applied to the AD7191 can also be
programmed.
Figure 10. ADC Setup Window
Rev. 0 | Page 8 of 20
Evaluation Board User Guide
UG-280
09880-011
LOW NOISE QUICK TEST
Figure 11. Low Noise Quick Test
When the Low Noise Quick Test button is clicked, you can
quickly and easily measure the rms noise of the AD7191.
The software provides instructions on the configuration of
the AD7191. When the instructions given on each window
are completed, click the ok button, The AD7191 gathers
100 samples, displays the results in the waveform, and analyzes
the data to calculate the maximum conversion, minimum
conversion, and average conversion. The rms noise, peak-topeak noise, and resolution are also calculated.
Rev. 0 | Page 9 of 20
UG-280
Evaluation Board User Guide
09880-012
WEIGHSCALE DEMO
Figure 12. Weigh Scale Demo
A load cell can be connected directly to the AD7191 evaluation
board. When the WeighScale Demo button is clicked, you are
guided through a series of windows that give information on
connecting the load cell to the AD7191 evaluation board. The
last window gives instructions on configuring the AD7191.
When the instructions given on each window are completed,
click OK. The AD7191 evaluation board gathers samples continuously and uses batches of 20 samples to analyze the data. The
software displays the maximum voltage measured, the average
voltage, the minimum voltage, the rms noise, and the resolution. The sample size used to process the data can be changed
using the Last # Samples box in the main window.
Rev. 0 | Page 10 of 20
Evaluation Board User Guide
UG-280
09880-013
USER UNITS SETUP
Figure 13. User Units Setup Window
The User Units Setup window allows you to define the display
units for the conversions. For example, if a load cell is connected to the AD7191, the conversions from the ADC can be
displayed in grams. The offset and gain error of the system can
also be calibrated. You can perform a system offset and system
full-scale calibration. The resulting coefficients are held in
memory.
Rev. 0 | Page 11 of 20
UG-280
Evaluation Board User Guide
EVALUATION BOARD SCHEMATICS AND ARTWORK
09880-017
Figure 14. EVAL-AD7191EBZ, Schematic (Digital Section)
Rev. 0 | Page 12 of 20
Evaluation Board User Guide
UG-280
09880-018
Figure 15. EVAL-AD7191EBZ, Schematic (Analog Section)
Rev. 0 | Page 13 of 20
Evaluation Board User Guide
09880-014
UG-280
09880-015
Figure 16. EVAL-AD7191EBZ, Component Side
Figure 17. EVAL-AD7191EBZ Silkscreen
Rev. 0 | Page 14 of 20
UG-280
09880-016
Evaluation Board User Guide
Figure 18. EVAL-AD7191EBZ, Solder Side
Rev. 0 | Page 15 of 20
UG-280
Evaluation Board User Guide
ORDERING INFORMATION
BILL OF MATERIALS
Table 2.
Designator
U1
U2
U31
U32
U50
U51
U52
U53
LED4 to LED8
XTAL1
XTAL51
D1
D31 to D34
Q51
C5 to C7, C15, C16
C52, C53
C8, C10, C11, C13
C19 to C24, C31 to
C33, C50, C54 to C61
C9, C12, C14
C34 to C38, C51
C17, C18, C25, C30
L1
R1, R2
R3 to R4, R8, R20 to
R25, R54
R6, R7, R52, R53
R12 to R15, R19, R50
R16
R17, R75, R76
R18, R31 to R37, R55
to R57, R61 to R70,
R72, R73
R58, R59
R74
S1 to S5
S6
B1
J1
J2, J3
J4
J5 to J9
J10
J31
J51
J52
Qty.
1
1
1
1
1
1
1
1
5
Manufacturer
Analog Devices
Analog Devices
Analog Devices
Analog Devices
Analog Devices
Cypress Semiconductor
Microchip Technology, Inc.
FCI
Avago Technology
Not inserted
AVX
ON Semiconductor
Philips
Infineon
Not inserted
Phycomp
Phycomp
Phycomp
Order No.
AD7191BRUZ
ADR421BRZ
ADP3303ARZ-5
ADP3303ARZ-3.3
AD5258BRMZ10
CY7C68013A-56LFXC
24LC64-I/SN
76341-308LF
HSME-C191
1
1
4
1
5
2
4
18
Description
AD7191
ADR421 reference
5 V voltage regulator
3.3 V voltage regulator
10 kΩ, 64-step digital potentiometer
USB controller
64k I2C EEPROM
LCD connector
LED green, high intensity (>50 mCd), 0603
4.9152 MHz crystal
24 MHz crystal
Diode
Diode
N-MOSFET
Capacitor ceramic
12 pF ceramic capacitor
0.01 μF ceramic capacitor
0.1 μF ceramic capacitor
3
6
4
1
2
10
1 μF ceramic capacitor
4.7 μF ceramic capacitor
10 μF tantalum capacitor
Ferrite bead
0 Ω resistor
100 Ω resistor
Phycomp
Phycomp
AVX
Tyco
Phycomp
Phycomp
2238 246 13663
2255 206 13672
TAJA106M016R
BMB2A1000LN2
232270296001
232270461001
4
10
1
1 kΩ resistor
10 kΩ resistor
1.5 Ω resistor
Resistor
100 kΩ resistor
Phycomp
Phycomp
Phycomp
Not inserted
Phycomp
232270461002
232270461003
232270461508
10 Ω resistor
47 Ω resistor
Switch
Switch, 8-way
Clip for 9 V battery
2 × 4 way header
2 × 8 way header
1 × 8 way header
Connector, 50 Ω, straight, SMB
Screw terminal block
Connector, power jack, barrel, 2.1 mm, SMD
Connector, USB Mini-B, SMD
Header
LCD module 2 × 16 char, 1 × 16-pin, top
LCD header
Phycomp
Phycomp
Omron
Omron
Keystone
Tyco/Amp
Tyco/Amp
Phoenix Contact
Not inserted
Phoenix Contact
Lumberg
Molex
Not inserted
Everbouquet
Tyco
232270461009
232270464709
B3S-1000
A6S-8102-H
593+594
1241050-4
1241050-8
1803332
23
2
1
5
1
1
1
2
1
1
1
1
1
1
Rev. 0 | Page 16 of 20
CX5032GB24000H0PESZZ
P6SMB6.8AT3G
BAT721C
BSS138N
2238 867 15129
2238 586 15636
2238 786 15649
232270461004
1727010
1613_14
548190572
MC1602C-SYR
1-826629-6
Evaluation Board User Guide
UG-280
RELATED LINKS
Resource
AD7191
ADR421
ADP3303
AD5258
Description
Product Page, Pin-Programmable, Ultralow Noise, 24-Bit, Sigma-Delta ADC for Bridge Sensors
Product Page, Ultraprecision, Low Noise, 2.500 V XFET® Voltage References
Product Page, High Accuracy anyCAP® 200 mA Low Dropout Linear Regulator
Product Page, Nonvolatile, I2C®-Compatible 64-Position, Digital Potentiometer
Rev. 0 | Page 17 of 20
UG-280
Evaluation Board User Guide
NOTES
Rev. 0 | Page 18 of 20
Evaluation Board User Guide
UG-280
NOTES
Rev. 0 | Page 19 of 20
UG-280
Evaluation Board User Guide
NOTES
I2C refers to a communications protocol originally developed by Philips Semiconductors (now NXP Semiconductors).
ESD Caution
ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection
circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality.
Legal Terms and Conditions
By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and conditions
set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation Board until you
have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you (“Customer”) and Analog Devices, Inc.
(“ADI”), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to Customer a free, limited, personal,
temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and agrees that the Evaluation Board is provided
for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted is expressly made subject to the following additional
limitations: Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board; and (ii) permit any Third Party to access the Evaluation Board. As used herein, the term
“Third Party” includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is NOT sold to Customer; all rights not expressly granted herein, including
ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all be considered the confidential and proprietary information of ADI. Customer may
not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of use of the Evaluation Board or termination of this Agreement, Customer agrees to
promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any
occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited to soldering or any other activity that affects the material content of the Evaluation Board.
Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice
to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS” AND ADI MAKES NO
WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED
TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL
PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S POSSESSION OR USE OF
THE EVALUATION BOARD, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE
AMOUNT OF ONE HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable
United States federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of
Massachusetts (excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby
submits to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly disclaimed.
©2011 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
UG09880-0-6/11(0)
Rev. 0 | Page 20 of 20
工商网监
湘ICP备2023018690号
