AME1084ACCS

Analog Microelectronics, Inc. AME1084 5A Low Dropout Positive Voltage Regulator n General Description The AME1084 is a 5A low-dropout positive voltage regulator. It is available in fixed and adjustable output voltage versions. Overcurrent and thermal protection are integrated onto the chip. Output current will limit as it reaches the pre-set current or temperature limit. At full rated output current the dropout voltage is 1.4V (max.). AME1084 series regulators provide excellent regulation over line, load and temperature variations. n Key Features l l l l l l l l Low dropout voltage … 1.4V at 5A Adjustable or 3.3V fixed voltage Line regulation typically 0.015% Load regulation typically 0.05% Adjust pin (ADJ) current less than 90µA Overcurrent protection Thermal protection Available in TO-220, TO-263, TO-252 n Applications l l l l High Efficiency Linear Regulators Post Regulators for Switching Supplies 5V to 3.3V Voltage Converter Battery Charger n Functional Block Diagram Input n Typical Application V IN AME1084V O U T GND 10 µF Tan Load Current Limiting Amplifier Thermal Protection 4.75V to 5.25V 10 µF Tan Output Figure 2 Error Amp. Bandgap Reference Figure 1 ADJ/GND 1 Analog Microelectronics, Inc. AME1084 5A Low Dropout Positive Voltage Regulator n Pin Configuration AME1084 AME 1084 1 2 3 A D J / G N D V OUT ADJ/GND V IN V O U T V IN TO-220 Front View T o-252 Front View AME 1084 1 2 3 AME 1084 1 2 3 A D J / G N D V OUT V IN A D J / G N D V OUT V IN TO-263-2 Front View TO-263-3 Front View 2 Analog Microelectronics, Inc. AME1084 5A Low Dropout Positive Voltage Regulator n Ordering Information P a rt Num be r A M E 1084A CB T M a rking A M E 1084 A CB T y y ww A M E 1084 B CB T y y ww A M E 1084 CCB T y y ww A M E 1084 DCB T y y ww A M E 1084 A CDT-3 y y ww A M E 1084 B CDT-3 y y ww A M E 1084 CCDT-3 y y ww A M E 1084 DCDT-3 y y ww A M E 1084 A CDT y y ww A M E 1084 B CDT y y ww A M E 1084 CCDT y y ww A M E 1084 DCDT y y ww A M E 1084 A CCS y y ww A M E 1084 B CCS y y ww A M E 1084 CCCS y y ww A M E 1084 DCCS y y ww Output V olta ge A DJ P a cka ge TO-220 A M E 1084B CB T 1.5 TO-220 A M E 1084CCB T 2.5 TO-220 A M E 1084DCB T 3.3 TO-220 A M E 1084A CDT-3 A DJ TO-263-3 A M E 1084B CDT-3 1.5 TO-263-3 A M E 1084CCDT-3 2.5 TO-263-3 A M E 1084DCDT-3 3.3 TO-263-3 A M E 1084A CDT A DJ TO-263-2 A M E 1084B CDT 1.5 TO-263-2 A M E 1084CCDT 2.5 TO-263-2 A M E 1084DCDT 3.3 TO-263-2 A M E 1084A CCS A DJ TO-252 A M E 1084B CCS 1.5 TO-252 A M E 1084CCCS 2.5 TO-252 A M E 1084DCCS 3.3 TO-252 3 Analog Microelectronics, Inc. AME1084 5A Low Dropout Positive Voltage Regulator n Absolute Maximum Ratings Parameter Input Voltage Thermal Resistance (Junction to Case) TO-220 TO-252 TO-263 TO-220 TO-252 TO-263 Symbol Maximum VIN 7 3 5 θJC 3 50 90 θJA 50 TJ 0 to 125 TSTG TLEAD -65 to 150 260 Unit V o C/W Thermal Resistance (Junction to Ambient) Operating Junction Temperature Range Storage Temperature Range Lead Temperature (10 sec) o C 4 Analog Microelectronics, Inc. AME1084 5A Low Dropout Positive Voltage Regulator n Electrical Characteristics 1. 1084AXXX Parameter Reference voltage (adjustable voltage) Line regulation Load regulation Dropout voltage ∆ VOUT, ∆ V REF = 1% Current limit Temperature Coefficient Adjust pin current Adjust pin current change Temperature stability Minimum load current RMS output noise Ripple rejection ratio Symbol V REF RegLINE RegLOAD VD IS TC IADJ ∆ IADJ TS IO VN RA VIN = 5V IO = 10mA VIN = 2.75 - 7V IO = 10mA VIN = 5V IO = 10mA - 5A VIN = 2.75 - 7V IO = 10mA - 5A VIN = 2.75 - 7V, Over temp. VIN = 2.75 - 7V, IO = 10mA - 5A VIN = 2.75 - 7V IO = 10mA - 5A TJ = 25 C Over temp. O Test Conditions TJ =25OC TJ = 25OC Over temp. TJ = 25OC Over temp. TJ = 25OC Over temp. Min. 1.238 5.0 0.5 60 Typ. 1.250 0.015 0.035 0.05 0.2 1.2 1.3 0.005 55 0.2 0.5 5 0.003 72 Max. 1.262 1.275 0.2 0.2 0.3 0.4 1.4 90 5 10 - Units V % % V A %/OC Over temp. 1.225 VIN = 2.75 - 7V, IO = 10mA - 5A Over temp. VIN = 5V, IO = 500mA, Over temp. VIN = 5V TJ = 25 C VIN = 5V, IO = 5A, Over temp. O µA % mA %V O dB 2. 1084DXXX Parameter Output voltage (fixed voltage) Line regulation Load regulation Dropout voltage ∆ V OUT, ∆ V REF = 1% Current limit Quiescent current (fixed model) Temperature Coefficient Temperature stability RMS output noise Ripple rejection ratio Symbol Vo RegLINE RegLOAD VD IS IQ TC TS VN RA V IN = 5V IO = 0A V IN = 4.5 - 7V IO = 0A V IN = 5V IO = 0A - 5A V IN = 4.5 - 7V IO = 0A - 5A V IN = 4.5 - 7V, Over temp. V IN =5V, Io=0-5A, Over temp. V IN = 4.5 - 7V, IO = 0A - 5A V IN = 5V, IO = 500mA, Over temp. TJ = 25 C V IN = 5V, IO = 5A, Over temp. O Test Conditions TJ = 25 C TJ = 25OC Over temp. TJ = 25OC Over temp. TJ = 25OC Over temp. O Min. 3.267 5.0 0.5 60 Typ. 3.300 0.015 0.035 0.05 0.2 1.2 1.3 12 0.005 0.5 0.003 72 Max. 3.333 3.366 0.2 0.2 0.3 0.4 1.4 13 - Units V % % V A mA %/ 0C % %V O dB 5 Over temp. 3.234 Analog Microelectronics, Inc. AME1084 5A Low Dropout Positive Voltage Regulator 3. Current limit protection AME1084 is protected against overload conditions. Current protection is triggered at typical 7.5A. 4. Stability and load regulation AME1084 requires a capacitor from VOUT to GND t o provide compensation feedback to the internal gain stage. This is to ensure stability at the output terminal. Typically, a 10µF tantalum or 50 µ F aluminum electrolytic is sufficient. Note: It is important that the ESR for this capacitor does not exceed 0.5Ω. The output capacitor dose not have a theoretical upper limit and increasing its value will increase stability. COUT = 100µF or more is typical for high current regulator design. For the adjustable version, the best load regulation is accomplished when the top of theresistor divider (R1) is connected directly to theoutput pin of the AME1084. When so connected, RP is not multiplied by the divider ratio. For fixed output versions, the top of R1 is internally connected to the output. The ground pin can be connected to low side of the load to eliminate ground loop errors. n Application Description 1. Output voltage adjustment Like most regulators, the AME1084 regulates the output by comparing the output voltage to an internally generated reference voltage. On the adjustable version, the VREF is available externally as 1.25V between VOUT and ADJ. The voltage ratio formed by R1 and R2 should be set to conduct 10mA (minimum output load). The output voltage is given by the following equation: R2 ) + IADJ x R2 VOUT = VREF ( 1 + R1 On fixed versions of AME1084, the voltage divider is provided internally. V IN C1 IN ADJ I AD J 50 µA OUT V REF R1 V OUT R2 V O U T = V R E F ( 1+ R 2 ) + I A D J x R 2 R1 Figure 3 RP Parasitic Line Resistance V IN IN ADJ OUT 2. Thermal protection AME1084 has thermal protection which limits junction temperature to 150OC. However, device functionality is only guaranteed to a maximum junction temperature of +125OC. The power dissipation and junction temperature for AME1084 in TO-220 package are given by PD = (VIN - VOUT) x IOUT TJUNCTION = TAMBIENT + ( PD x θJA) Note: TJUNCTION must not exceed 125OC R1 (Connect R1 to case) RL R2 Connect R2 to load Figure 4 6 Analog Microelectronics, Inc. AME1084 5A Low Dropout Positive Voltage Regulator 5. Thermal consideration The AME1084 series contain thermal limiting circuitry designed to protect itself for overtemperature conditions. Even for normal load conditions, maximum junction temperature ratings must not be exceed. As mention in thermal protection section, we need to consider all sources of thermal resistance between junction and ambient. It includes junction-to-case, case-to-heat-sink interface and heat sink thermal resistance itself. Junction-to-case thermal resistance is specified from the IC junction to the bottom of the case directly below the die. Proper mounting is required to ensure the best possible thermal flow from this area of the package to the heat sink. The case of all devices in this series is electrically connected to the output. Therefore, if the case of the device must be electrically isolated, a thermally conductive spacer is recommended. 7 Analog Microelectronics, Inc. AME1084 5A Low Dropout Positive Voltage Regulator n Advanced Applications V IN = 5 V AME1084 V OUT V IN ADJ R1 10 µF 1K * V O = 1 .5 - 3.45V 10 µF 10 µF ** R2 2K * VO = VREF (1 + R2 ) + IADJ x R2 R1 ** Optional for improved ripple rejection Figure 5 Adjustable Output Voltage V IN AME1084 V IN GND V OUT R1 * 20m Ω VO I O = 0 t o 10A 10 µF 10 µF AME1084 V IN GND V OUT R2 * 20m Ω * 20mW is ballast resistance The inter - connection of #18 wire could act as ballast resistance Figure 6 Paralleling Regulators 8 Analog Microelectronics, Inc. AME1084 5A Low Dropout Positive Voltage Regulator n Advanced Applications (Cont.) V IN V IN GND 10 µF 10 µF 1K 10 µF AME1084 V OUT * VO ** Zener diode or voltage reference * VO = VREF + VZ (VZ: breakdown voltage of Zener diode) ** Optional for improved ripple rejection Figure 7 Regulator with Reference * V IN 10 µF AME1084 V OUT GND VO 100 µF Figure 8 Regulator with Reverse Diode Protection 9 Analog Microelectronics, Inc. AME1084 5A Low Dropout Positive Voltage Regulator n Performance Characteristics Drop-out Voltage vs. Load Current 1.30 1.25 Minimum Operation Current vs Input/Output Differential Voltage 7 Minimum Operation Current (mA) 6 5 4 3 2 1 0 0 1 2 3 4 5 6 7 8 9 Drop-out Volatge (V) 1.20 1.15 1.10 1.05 1.00 0.95 0.90 0 1 2 3 4 5 Load Current (A) Input/Output Differential Voltage(V) Output Short circuit Current vs Input/Output Differential Voltage Output Short Circuit Current (A) 9 8 7 6 5 4 3 2 1 0 1 2 3 4 5 6 7 8 9 Input/Output Differential Voltage(V) 10 Analog Microelectronics, Inc. AME1084 5A Low Dropout Positive Voltage Regulator n External Resistor Divider Table for Customized Voltage R1(ohm) Vout 1.25 1.30 1.35 1.40 1.45 1.50 1.55 1.60 1.65 1.70 1.75 1.80 1.85 1.90 1.95 2.00 2.05 2.10 2.15 2.20 2.25 2.30 2.35 2.40 2.45 2.50 2.55 2.60 2.65 2.70 2.75 2.80 2.85 2.90 2.95 3.00 3.05 3.10 100 0.000 3.984 7.968 11.95 15.94 19.92 23.90 27.89 31.87 35.86 39.84 43.82 47.81 51.79 55.78 59.76 63.75 67.73 71.71 75.70 79.68 83.67 87.65 91.63 95.62 99.60 103.6 107.6 111.6 115.5 119.5 123.5 127.5 131.5 135.5 139.4 143.4 147.4 102 0.000 4.063 8.127 12.19 16.25 20.32 24.38 28.44 32.51 36.57 40.63 44.70 48.76 52.82 56.89 60.95 65.01 69.08 73.14 77.21 81.27 85.33 89.40 93.46 97.52 101.6 105.6 109.7 113.8 117.8 121.9 126.0 130.0 134.1 138.2 142.2 146.3 150.3 105 107 110 113 115 118 R2(ohm)=(Vout-1.25)*R1/(1.25+50u*R1) 0.000 0.000 0.000 0.000 0.000 0.000 4.182 4.262 4.381 4.500 4.579 4.698 8.365 8.524 8.761 8.999 9.158 9.396 12.55 12.79 13.14 13.50 13.74 14.09 16.73 17.05 17.52 18.00 18.32 18.79 20.91 21.31 21.90 22.50 22.89 23.49 25.09 25.57 26.28 27.00 27.47 28.19 29.28 29.83 30.67 31.50 32.05 32.88 33.46 34.09 35.05 36.00 36.63 37.58 37.64 38.36 39.43 40.50 41.21 42.28 41.82 42.62 43.81 45.00 45.79 46.98 46.01 46.88 48.19 49.50 50.37 51.68 50.19 51.14 52.57 54.00 54.95 56.37 54.37 55.40 56.95 58.50 59.53 61.07 58.55 59.66 61.33 63.00 64.11 65.77 62.74 63.93 65.71 67.49 68.68 70.47 66.92 68.19 70.09 71.99 73.26 75.17 71.10 72.45 74.47 76.49 77.84 79.86 75.28 76.71 78.85 80.99 82.42 84.56 79.47 80.97 83.23 85.49 87.00 89.26 83.65 85.24 87.61 89.99 91.58 93.96 87.83 89.50 92.00 94.49 96.16 98.65 92.01 93.76 96.38 98.99 100.7 103.4 96.20 98.02 100.8 103.5 105.3 108.1 100.4 102.3 105.1 108.0 109.9 112.7 104.6 106.5 109.5 112.5 114.5 117.4 108.7 110.8 113.9 117.0 119.1 122.1 112.9 115.1 118.3 121.5 123.6 126.8 117.1 119.3 122.7 126.0 128.2 131.5 121.3 123.6 127.0 130.5 132.8 136.2 125.5 127.9 131.4 135.0 137.4 140.9 129.7 132.1 135.8 139.5 141.9 145.6 133.8 136.4 140.2 144.0 146.5 150.3 138.0 140.6 144.6 148.5 151.1 155.0 142.2 144.9 148.9 153.0 155.7 159.7 146.4 149.2 153.3 157.5 160.3 164.4 150.6 153.4 157.7 162.0 164.8 169.1 154.8 157.7 162.1 166.5 169.4 173.8 121 0.000 4.817 9.633 14.45 19.27 24.08 28.90 33.72 38.53 43.35 48.17 52.98 57.80 62.62 67.43 72.25 77.07 81.88 86.70 91.52 96.33 101.2 106.0 110.8 115.6 120.4 125.2 130.1 134.9 139.7 144.5 149.3 154.1 159.0 163.8 168.6 173.4 178.2 124 0.000 4.936 9.871 14.81 19.74 24.68 29.61 34.55 39.48 44.42 49.36 54.29 59.23 64.16 69.10 74.03 78.97 83.90 88.84 93.77 98.71 103.6 108.6 113.5 118.5 123.4 128.3 133.3 138.2 143.1 148.1 153.0 157.9 162.9 167.8 172.7 177.7 182.6 11 Analog Microelectronics, Inc. AME1084 5A Low Dropout Positive Voltage Regulator n External Resistor Divider Table for Customized Voltage R1(ohm) Vout 3.15 3.20 3.25 3.30 3.35 3.40 3.45 3.50 3.55 3.60 3.65 3.70 3.75 3.80 3.85 3.90 3.95 4.00 4.05 4.10 4.15 4.20 4.25 4.30 4.35 4.40 4.45 4.50 4.55 4.60 4.65 4.70 4.75 4.80 4.85 4.90 4.95 5.00 100 151.4 155.4 159.4 163.3 167.3 171.3 175.3 179.3 183.3 187.3 191.2 195.2 199.2 203.2 207.2 211.2 215.1 219.1 223.1 227.1 231.1 235.1 239.0 243.0 247.0 251.0 255.0 259.0 262.9 266.9 270.9 274.9 278.9 282.9 286.9 290.8 294.8 298.8 102 154.4 158.5 162.5 166.6 170.7 174.7 178.8 182.9 186.9 191.0 195.0 199.1 203.2 207.2 211.3 215.4 219.4 223.5 227.6 231.6 235.7 239.7 243.8 247.9 251.9 256.0 260.1 264.1 268.2 272.2 276.3 280.4 284.4 288.5 292.6 296.6 300.7 304.8 105 107 110 113 115 118 R2(ohm)=(Vout-1.25)*R1/(1.25+50u*R1) 158.9 161.9 166.5 171.0 174.0 178.5 163.1 166.2 170.8 175.5 178.6 183.2 167.3 170.5 175.2 180.0 183.2 187.9 171.5 174.7 179.6 184.5 187.7 192.6 175.7 179.0 184.0 189.0 192.3 197.3 179.8 183.3 188.4 193.5 196.9 202.0 184.0 187.5 192.8 198.0 201.5 206.7 188.2 191.8 197.1 202.5 206.1 211.4 192.4 196.0 201.5 207.0 210.6 216.1 196.6 200.3 205.9 211.5 215.2 220.8 200.8 204.6 210.3 216.0 219.8 225.5 204.9 208.8 214.7 220.5 224.4 230.2 209.1 213.1 219.0 225.0 228.9 234.9 213.3 217.3 223.4 229.5 233.5 239.6 217.5 221.6 227.8 234.0 238.1 244.3 221.7 225.9 232.2 238.5 242.7 249.0 225.9 230.1 236.6 243.0 247.3 253.7 230.0 234.4 240.9 247.5 251.8 258.4 234.2 238.7 245.3 252.0 256.4 263.1 238.4 242.9 249.7 256.5 261.0 267.8 242.6 247.2 254.1 261.0 265.6 272.5 246.8 251.4 258.5 265.5 270.2 277.2 250.9 255.7 262.8 270.0 274.7 281.9 255.1 260.0 267.2 274.5 279.3 286.6 259.3 264.2 271.6 279.0 283.9 291.3 263.5 268.5 276.0 283.5 288.5 296.0 267.7 272.8 280.4 288.0 293.1 300.7 271.9 277.0 284.7 292.5 297.6 305.4 276.0 281.3 289.1 297.0 302.2 310.1 280.2 285.5 293.5 301.5 306.8 314.8 284.4 289.8 297.9 306.0 311.4 319.5 288.6 294.1 302.3 310.5 315.9 324.2 292.8 298.3 306.7 315.0 320.5 328.8 297.0 302.6 311.0 319.5 325.1 333.5 301.1 306.8 315.4 324.0 329.7 338.2 305.3 311.1 319.8 328.5 334.3 342.9 309.5 315.4 324.2 333.0 338.8 347.6 313.7 319.6 328.6 337.5 343.4 352.3 121 183.0 187.9 192.7 197.5 202.3 207.1 211.9 216.8 221.6 226.4 231.2 236.0 240.8 245.7 250.5 255.3 260.1 264.9 269.7 274.6 279.4 284.2 289.0 293.8 298.6 303.5 308.3 313.1 317.9 322.7 327.5 332.4 337.2 342.0 346.8 351.6 356.4 361.3 124 187.5 192.5 197.4 202.4 207.3 212.2 217.2 222.1 227.0 232.0 236.9 241.8 246.8 251.7 256.6 261.6 266.5 271.5 276.4 281.3 286.3 291.2 296.1 301.1 306.0 310.9 315.9 320.8 325.7 330.7 335.6 340.6 345.5 350.4 355.4 360.3 365.2 370.2 12 Analog Microelectronics, Inc. AME1084 5A Low Dropout Positive Voltage Regulator n Package Dimension TO-220 SYMBOLS A b C1 D E e e1 e3 f H1 K CP Q L a b1 R MILLIMETERS MIN MAX 4.06 4.83 0.63 1.02 0.35 0.60 14.22 14.99 9.66 10.54 2.79 4.83 5.33 1.14 1.40 1.14 1.40 5.94 6.55 2.29 2.92 3.71 3.96 2.62 2.87 12.70 14.27 3D 7D 1.14 1.52 6.17 REF. INCHES MIN MAX 0.160 0.190 0.025 0.040 0.0138 0.0236 0.056 0.590 0.385 0.415 0.110 0.190 0.210 0.045 0.055 0.045 0.055 0.234 0.258 0.090 0.115 0.146 0.156 0.103 0.113 0.500 0.5618 3D 7D 0.0449 0.06 0.243 REF. Notes : 1. Dimension C1 apply for tin plate finish. 2. For solder dip lead finish dimension C1 should be 0.015"-0.027" (0.38-0.69) TO-263-3 SYM BOLS A B C D E G H K L M N P R S W * M ILLIM ETER S M IN M AX 9.65 10.41 8.28 9.65 4.06 4.83 0.51 1.02 1.14 1.40 * 2.54 14.61 15.88 1.02 1.68 0.00 0.97 2.49 2.74 0.43 0.58 2.29 2.79 o 8? 0 2.41 2.67 0.254 0.508 IN CHES M IN M AX 0.380 0.410 0.326 0.380 0.160 0.190 0.020 0.040 0.045 0.055 * 0.100 0.575 0.625 0.040 0.066 0.000 0.038 0.098 0.108 0.017 0.023 0.090 0.110 o 0 8? 0.095 0.105 0.010 0.020 : Typical value N OTES : 1. CON TR OLLIN G D IM EN SION : M ILLIM ETER S. 2M AXIM UM LEAD THICKN ESS IN CLUD ES LEAD FIN ISH THICKN ESS M IN IM UM LEAD THICKN ESS IS THE M IN IM UM THICKN ESS OF BASE M ATER IA. 13 Analog Microelectronics, Inc. AME1084 5A Low Dropout Positive Voltage Regulator n Package Dimension TO-263-2 SYMBOLS A B C D E G H K L M N P R S W * MILLIMETERS MIN MAX 9.65 10.41 8.28 9.65 4.06 4.83 0.51 1.02 1.14 1.40 * 2.54 14.61 15.88 1.02 1.68 0.00 0.97 2.49 2.74 0.43 0.58 2.29 2.79 o 8? 0 2.41 2.67 0.254 0.508 INCHES MIN MAX 0.380 0.410 0.326 0.380 0.160 0.190 0.020 0.040 0.045 0.055 * 0.100 0.575 0.625 0.040 0.066 0.000 0.038 0.098 0.108 0.017 0.023 0.090 0.110 o 0 8? 0.095 0.105 0.010 0.020 : Typical value NOTES : 1. CONTROLLING DIMENSION : MILLIMETERS. 2MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH THICKNESS MINIMUM LEAD THICKNESS IS THE MINIMUM THICKNESS OF BASE MATERIA. 14 Analog Microelectronics, Inc. AME1084 5A Low Dropout Positive Voltage Regulator n Package Dimension TO-252 (DPAK) SYMBOLS A B C D E F G H I J K L * : Typical value NOTES : 1. CONTROLLING DIMENSION : MILLIMETERS. 2. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH THICKNESS MINIMUM LEAD THICKNESS IS THE MINIMUM THICKNESS OF BASE MATERIAL. MILLIMETERS MIN MAX 0.45 0.58 1.60 1.95 0.51 0.45 0.60 6.40 6.80 5.40 5.80 2.20 2.85 * 2.30 0.90 0.97 5.20 5.50 0.89 2.03 INCHES MIN MAX 0.0177 0.023 0.06 0.0768 0.02 0.0177 0.0236 0.252 0.2677 0.2126 0.2283 0.0866 0.1122 * 0.0906 0.0354 0.038 0.20 0.22 0.035 0.08 TO-252 (DPAK) SYMBOLS A B C D E F G H I J K L * : Typical value NOTES : 1. CONTROLLING DIMENSION : MILLIMETERS. 2. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH THICKNESS MINIMUM LEAD THICKNESS IS THE MINIMUM THICKNESS OF BASE MATERIAL. MILLIMETERS MIN MAX 0.45 0.58 1.60 1.95 0.51 0.45 0.60 6.40 6.80 5.40 5.80 2.20 2.85 * 2.30 0.90 0.97 5.20 5.50 0.89 2.03 INCHES MIN MAX 0.0177 0.023 0.06 0.0768 0.02 0.0177 0.0236 0.252 0.2677 0.2126 0.2283 0.0866 0.1122 * 0.0906 0.0354 0.038 0.20 0.22 0.035 0.08 15 www.analogmicro.com E-Mail: info@analogmicro.com Life Support Policy: These products of Analog Microelectronics, Inc. are not authorized for use as critical components in lifesupport devices or systems, without the express written approval of the president of Analog Microelectronics, Inc. Analog Microelectronics, Inc. reserves the right to make changes in the circuitry and specifications of its devices and advises its customers to obtain the latest version of relevant information. © Analog Microelectronics, Inc. , July 2001 Document: 1012-doc-B-0704 Corporate Headquarters Analog Microelectronics, Inc. 3100 De La Cruz Blvd. Suite 201 Santa Clara, CA. 95054-2046 Tel : (408) 988-2388 Fax: (408) 988-2489 Asia Pacific Headquarters AME, Inc. 2F, 187 ,Kang-Chien Rd, Nei-Hu District Taipei 114, Taiwan, R.O.C. Tel : 886 2 2627-8687 Fax : 886 2 2659-2989