PTH03060WAZT

PTH03060 3.3 Vin single output DC-DC CONVERTERS • • • • • • • • • • • POLA Non-isolated 1 NEW Product 10 A output current 3.3 V input voltage Wide-output voltage adjust (0.8 Vdc to 2.5 Vdc) Auto-track™ sequencing* Margin up/down controls Pre-bias start-up capability Efficiencies up to 93% Output ON/OFF inhibit Output voltage sense Point-of-Load-Alliance (POLA) compatible Available RoHS compliant The PTH03060 is a next generation series of non-isolated dc-dc converters offering some of the most advanced POL features available in the industry. The primary new feature provides for sequencing between multiple modules, a function, which is becoming a necessity for powering advanced silicon including DSP’s, FPGA’s and ASIC’s requiring controlled power-up and power down. Other industry leading features include margin up/down controls, pre-bias start-up capability and efficiencies up to 93%. The PTH03060 has an input voltage of 2.95 Vdc to 3.65 Vdc and offers a wide 0.8 Vdc to 2.5 Vdc output voltage range with up to 10 A output current, which allows for maximum design flexibility and a pathway for future upgrades. 2 YEAR WARRANTY All specifications are typical at nominal input, full load at 25 °C unless otherwise stated Cin = 330 µF, Cout = 0 µF OUTPUT SPECIFICATIONS Voltage adjustability EMC CHARACTERISTICS (See Note 4) Setpoint accuracy 0.8-2.5 Vdc ±2.0% Vo Line regulation ±10 mV typ. Load regulation ±12 mV typ. Total regulation ±3.0% Vo Minimum load Ripple and noise 0A 20 MHz bandwidth Temperature co-efficient -40 ºC to +85 ºC 20 mV pk-pk ±0.5% Vo 70 µs recovery time Overshoot/undershoot 100 mV Transient response (See Note 5) Margin adjustment ±5.0% Vo Electrostatic discharge Conducted immunity Radiated immunity EN61000-4-2, IEC801-2 EN61000-4-6 EN61000-4-3 GENERAL SPECIFICATIONS Efficiency (See Efficiency Table) Insulation voltage 300 kHz typ. ±25 kHz Switching frequency Approvals and standards EN60950 UL/cUL60950 Material flammability Dimensions Input voltage range (See Note 3) Input current No load Remote ON/OFF (See Note 1) 2.95-3.65 Vdc 10 mA typ. Positive logic Start-up time 1 V/ms 2.8-2.95 Vdc typ. Undervoltage lockout Pin 8 (See Note 6, 7) MTBF 93% max. Non-isolated UL94V-0 (L x W x H) 25.27 x 15.75 x 9.00 mm 0.995 x 0.620 x 0.354 in Weight INPUT SPECIFICATIONS Track input voltage SPECIFICATIONS 3.7 g (0.13 oz) Telcordia SR-332 7,092,000 hours ENVIRONMENTAL SPECIFICATIONS Thermal performance (See Note 2) MSL (‘Z’ suffix only) Operating ambient, temperature Non-operating JEDEC J-STD-020C -40 ºC to +85 ºC -40 ºC to +125 ºC Level 3 ±0.3 Vin PROTECTION International Safety Standard Approvals UL/cUL CAN/CSA-C22.2 No. 60950-1-03/UL 60950-1, File No. E174104 TÜV Product Service (EN60950) Certificate No. B 04 06 38572 044 CB Report and Certificate to IEC60950, Certificate No. US/8292/UL Short-circuit Auto reset 20 A typ. *Auto-track™ is a trade mark of Texas Instruments File Name: pth03060.pdf Rev: 28 Jun 2006 PTH03060 3.3 Vin single output DC-DC CONVERTERS POLA Non-isolated 2 For the most current data and application support visit www.artesyn.com/powergroup/products.htm NEW Product OUTPUT POWER (MAX.) INPUT VOLTAGE OUTPUT VOLTAGE OUTPUT CURRENT (MIN.) OUTPUT CURRENT (MAX.) EFFICIENCY (MAX.) LINE LOAD MODEL NUMBER (9,10) 25 W 2.95-3.65 Vdc 0.8-2.5 Vdc 0A 10 A 93% ±10 mV ±12 mV PTH03060 Part Number System with Options REGULATION PTH03060WAST Product Family Point of Load Alliance Compatible Input Voltage 03 = 3.3 V Output Current 06 = 10 A Mechanical Package Always 0 Packaging Options No Suffix = Trays T = Tape and Reel (8) Mounting Option (9) D = Horizontal Through-Hole (Matte Sn) H = Horizontal Through-Hole (Sn/Pb) S = Surface-Mount (63/37 Sn/Pb pin solder material) Z = Surface-Mount (95.5/3.8/0.7 Sn/Ag/Cu pin solder material) Pin Option A = Through-Hole Std. Pin Length (0.140”) A = Surface-Mount Tin/Lead Solder Ball Output Voltage Code W = Wide Output Voltage Adjustment of the PTH03060 Series The ultra-wide output voltage trim range offers major advantages to users who select the PTH03060. It is no longer necessary to purchase a variety of modules in order to cover different output voltages. The output voltage can be trimmed in a range of 0.8 Vdc to 2.5 Vdc. When the PTH03060 converter leaves the factory the output has been adjusted to the default voltage of 0.8 V. Notes Remote ON/OFF. Positive Logic ON: Pin 3 open; or V > Vin - 0.5 V OFF: Pin 3 GND; or V < 0.8 V (min - 0.2 V). 2 See Figure 1 for safe operating curve. 3 A 330 µF electrolytic input capacitor is required for proper operation. The capacitor must be rated for a minimum of 700 mA rms of ripple current. 4 An external output capacitor is not required for basic operation. Adding 330 µF of distributed capacitance at the load will improve the transient response. 5 1 A/µs load step, 50 to 100% Iomax, Cout = 330 µF. 6 If utilized Vout will track applied voltage by ±0.3 V (up to Vo set point). 7 The pre-bias start-up feature is not compatible with Auto-Track™. This is because when the module is under Auto-Track™ control, it is fully active and will sink current if the output voltage is below that of a back-feeding source. Therefore to ensure a pre-bias hold-off, one of the following two techniques must be followed when input power is first applied to the module. The Auto-Track™ function must either be disabled, or the module’s output held off using the Inhibit pin. Refer to Application Note 154 for more details. 8 Tape and reel packaging only available on the surface-mount versions. 9 To order Pb-free (RoHS compatible) surface-mount parts replace the mounting option ‘S’ with ‘Z’, e.g. PTH03060WAZ. To order Pb-free (RoHS compatible) through-hole parts replace the mounting option ‘H’ with ‘D’, e.g. PTH03060WAD. 10 NOTICE: Some models do not support all options. Please contact your local Artesyn representative or use the on-line model number search tool at http://www.artesyn.com/powergroup/products.htm to find a suitable alternative. 1 EFFICIENCY TABLE (IO = 7 A) OUTPUT VOLTAGE EFFICIENCY Vo = 1.0 V 85% Vo = 1.2 V 87% Vo = 1.5 V 89% Vo = 1.8 V 91% Vo = 2.0 V 92% Vo = 2.5 V 93% File Name: pth03060.pdf Rev: 28 Jun 2006 PTH03060 3.3 Vin single output DC-DC CONVERTERS POLA Non-isolated 3 For the most current data and application support visit www.artesyn.com/powergroup/products.htm NEW Product 80 100 70 90 400LFM 60 200LFM 100LFM Nat conv 50 40 30 EFFICIENCY (%) TEMPERATURE (ºC) 90 Vout 2.5V 1.8V 1.2V 80 70 0.8V 60 50 40 20 0 0 2 4 6 8 2 4 6 8 10 10 OUTPUT CURRENT (A) OUTPUT CURRENT (A) Figure 2 - Efficiency vs Load Current Vin = 3.3 V (See Note B) Figure 1 - Safe Operating Area Vin = 3.3 V, Output Voltage = 2.5 V (See Note A) Notes Track Margin Down Margin Up 10 9 A SOA curves represent the conditions at which internal components are within the Artesyn derating guidelines. B Characteristic data has been developed from actual products tested at 25 °C. This data is considered typical data for the converter. 8 1 7 PTH03060 (Top View) Vin Vout 6 2 3 Inhibit + Cin 330µF (Required) 4 5 Vo Sense RSET 1%, 0.1W (Required) + Cout 330µF (Optional) L O A D GND GND Figure 3 - Standard Application File Name: pth03060.pdf Rev: 28 Jun 2006 PTH03060 3.3 Vin single output DC-DC CONVERTERS POLA Non-isolated 4 For the most current data and application support visit www.artesyn.com/powergroup/products.htm 0.995 (25.27) 0.125 (3.18) 0.125 (3.18) 0.060 (1.52) 0.140 (3.55) 0.060 (1.52) 0.250 (6.35) 0.375 (9.52) 1 9 10 8 ø0.040 (1.02) 5 Places. 7 0.070 (1.78) (Standoff Shoulder) 0.620 0.500 (12.70) (15.75) 2 3 5 4 Lowest Component 0.010 min. (0.25) Bottom side Clearance 6 PIN CONNECTIONS TOP VIEW Host Board Dimensions in Inches (mm) Tolerances (unless otherwise specified) 2 Places ±0.030 (±0.76) 3 Places ±0.010 (±0.25) 1 9 10 0.060 (1.52) 0.250 (6.35) 8 Ground 2 Vin SIDE VIEW 3 Inhibit* 4 Vo adjust 5 Vo sense 6 Vout 7 Ground 8 Track 9 Margin down* 10 Margin up* 0.354 (9.00) max.* 7 3 4 TOP VIEW 5 *After solder reflow on customer board *Denotes negative logic: Open = Normal operation Ground = Function active Solder Ball 0.040 (1.02) 10 Places 0.500 0.620 (12.70) (15.75) 2 FUNCTION 1 0.995 (25.27) 0.125 (3.18) 0.125 (3.18) 0.375 (9.52) PIN NO. 0.354 (9.00) MAX. Figure 1 - Plated Through-Hole Mechanical Drawing 0.060 (1.52) NEW Product 6 SIDE VIEW Dimensions in Inches (mm) Tolerances (unless otherwise specified) 2 Places ±0.030 (±0.76) 3 Places ±0.010 (±0.25) Figure 2 - Surface-Mount Mechanical Drawing Datasheet © Artesyn Technologies® 2006 The information and specifications contained in this datasheet are believed to be correct at time of publication. However, Artesyn Technologies accepts no responsibility for consequences arising from printing errors or inaccuracies. The information and specifications contained or described herein are subject to change in any manner at any time without notice. No rights under any patent accompany the sale of any such product(s) or information contained herein. Please consult our website for the following items: 4 Application Note www.artesyn.com File Name: pth03060.pdf Rev: 28 Jun 2006