BT05AG_1

BT05AG 5-4000 MHz Wideband Drive Amplifier Device Features      OIP3 = 40.0 dBm @ 1900 MHz Gain = 20.8 dB @ 900 MHz Output P1 dB = 22.4 dBm @ 900 MHz 50 Ω Cascadable Lead-free/RoHS-compliant SOT-89 SMT package Typical Performance1 Parameter 900 Gain S11 S22 OIP3 P1dB Noise Figure 1 2 Product Description BeRex’s BT05AG is a high performance and a high dynamic range amplifier in a low cost surface mount package(SOT-89) with a RoHS -compliant, that incorporates reliable heterojunction-bipolar-transistor (HBT) devices fabricated with InGaP GaAs technology. This device is designed for use where high linearity is required and features high OIP3 and P1 with low consumption current (85mA) and requires a few external matching components such as a DC blocking capacitors on the In/Output pin, a bypass capacitor and a RF choke for the out port. All devices are 100% RF/DC tested. Applications  Base station Infrastructure/RFID  Commercial/Industrial/Military wireless system Frequency 1900 16.3 -20.0 -12.0 40.0 19.5 4.4 2450 14.3 -22.0 -12.0 37.5 23.0 4.3 3500 11.1 -16.0 -13.0 40.0 22.8 4.5 Unit MHz dB dB dB dBm dBm dB 20.8 -14.0 -12.0 2 37.0 22.4 4.5 Device performance _ measured on a BeRex evaluation board at 25°C, 50 Ω system. OIP3 _ measured with two tones at an output of 10 dBm per tone separated by 1 MHz. Min. Bandwidth IC @ (Vc = 5V) VC RTH 5 75 Typical 85 5.0 50 Max. 4000 95 Unit MHz mA V °C/W Absolute Maximum Ratings Parameter Operating Case Temperature Storage Temperature Junction Temperature Operating Voltage Supply Current Input RF Power Rating -40 to +85 -55 to +155 +220 +7.0 180 23 Unit °C °C °C V mA dBm Application Circuits Vcc Bypass RF Choke RF In DC Block BT05AG RF Out DC Block *Operation of this device above any of these parameters may result in permanent damage. *external matching circuit: refer to the page 5 to 11. BeRex ● website: www.berex.com ● email: sales@berex.com 1 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark o f BeRex. All other trademarks are the property of their respective owners. © 2010 BeRex Rev. C BT05AG 5-4000 MHz Wideband Drive Amplifier V-I Characteristics BeRex SOT89 Evaluation Board BeRex Evaluation Board *Dielectric constant _ 4.2 *RF pattern width 52mil *31mil thick FR4 PCB Typical Device Data S-parameters (Vc=5V, Ic=84mA, T=25°C) BeRex ● website: www.berex.com ● email: sales@berex.com 2 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark o f BeRex. All other trademarks are the property of their respective owners. © 2010 BeRex Rev. C BT05AG 5-4000 MHz Wideband Drive Amplifier S-Parameter (Vdevice = 5.0V, Icc = 84mA, T = 25 °C, calibrated to device leads) Freq [MHz] 100 500 1000 1500 2000 2500 3000 3500 4000 S11 -10.6001 -6.89632 -4.83571 -4.36842 -4.49519 -4.82222 -4.64574 -3.85543 -3.0184 S11 -176.08 171.969 137.774 107.055 77.2739 43.2334 3.39018 -35.846 -66.883 S21 24.3773 22.4951 19.3111 16.5624 14.5732 13.1214 11.7047 9.92492 8.4767 S21 166.26 118.889 75.4763 42.7846 13.4329 -15.725 -45.735 -74.765 -100.82 S12 -29.173 -28.510 -27.637 -27.010 -26.080 -25.166 -24.318 -25.101 -24.247 S12 -0.828 -5.512 -16.88 -29.70 -41.79 -58.33 -79.25 -100.4 -119.41 S22 -21.805 -20.525 -17.519 -16.447 -17.536 -22.101 -27.037 -16.664 -11.732 S22 -27.056 -120.815 170.039 137.451 118.289 99.7268 4.66192 -50.8784 -71.031 WCDMA 6FA 2140 -55dBc BeRex ● website: www.berex.com ● email: sales@berex.com 3 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark o f BeRex. All other trademarks are the property of their respective owners. © 2010 BeRex Rev. C BT05AG 5-4000 MHz Wideband Drive Amplifier WCDMA 6FA 2140 -60dBc ACLR BeRex ● website: www.berex.com ● email: sales@berex.com 4 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark o f BeRex. All other trademarks are the property of their respective owners. © 2010 BeRex Rev. C BT05AG 5-4000 MHz Wideband Drive Amplifier Application Circuit: 900 MHz Schematic Diagram C1 C2 C3 BOM +5V Tolerance ±5% ±5% ±20% ±5% ±5% ±5% ±5% ±5% ±5% L1 RFin C4 C7 BT05AG C5 RFout C6 L2 C1 C2 C3 C4 C5 C6 C7 L1 L2 100pF 1000pF 10uF 100pF 100pF 1pF 4.7pF 39nH 5.6nH Note: 10uF 1. 2. PCB: 31mil thick FR4 Distance between the center of the series cap (C7) and the input pin of BT05AG _ 2.0mm. Distance between the center of the shunt inductor(L2) and the input pin of BT05AG _ 4.1mm. Distance between the center of the shunt cap (C6) and the input pin of BT05AG _ 6.5mm. 1000 pF 100pF 100 pF 4.7pF 100pF 1pF 5.6nH BT05AG BT013 39nH 3. 100pF B B B 4. Typical Performance 0 0 +25C -5 +25C -30C -5 -30C +85C +85C S11 [dB] -10 S22 [dB] 850 900 950 1000 -10 -15 -15 -20 800 -20 800 850 900 950 1000 Freq [MHz] Freq [MHz] BeRex ● website: www.berex.com ● email: sales@berex.com 5 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark o f BeRex. All other trademarks are the property of their respective owners. © 2010 BeRex Rev. C BT05AG 5-4000 MHz Wideband Drive Amplifier 23 25 70 60 22 20 50 21 S21 [dB] 20 Po, G 15 40 30 20 10 19 +25C 18 -30C +85C 5 Po G PAE 10 0 -20 -14 -8 -2 4 10 17 800 850 900 950 1000 0 Freq [MHz] Pin [dBm ] F1=900MHz, F2=901MHz 40 38 36 34 32 30 28 26 10 12 14 16 18 +25C -30C +85C 0 -10 -20 900MHz, 885KHz offset 9-Ch FWD, IS-95 +25C -30C +85C OIP3 [dBm] ACPR [dBc] -30 -40 -50 -60 -70 -80 10 12 14 16 Po, 2tone [dBm ] Po [dBm ] BeRex ● website: www.berex.com ● email: sales@berex.com PAE [%] 18 6 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark o f BeRex. All other trademarks are the property of their respective owners. © 2010 BeRex Rev. C BT05AG 5-4000 MHz Wideband Drive Amplifier Application Circuit: 1900 MHz Schematic Diagram C1 C2 C3 BOM +5V Tolerance ±5% ±5% ±20% ±5% ±5% ±5% ±5% ±5% ±5% L1 RFin C4 BT05AG L2 C5 C6 C7 RFout C1 C2 C3 C4 C5 C6 C7 L1 L2 100pF 100pF 10uF 100pF 100pF 2pF 1pF 39nH 3.3nH Note: 10uF 1. 2. PCB: 31mil thick FR4 Distance between the center of the shunt cap (C6) and the input pin of BT05AG _ 1.8mm. Distance between the center of the series inductor(L2) and the output pin of BT05AG _ 3.5mm. Distance between the center of the shunt cap (C7) and the output pin of BT05AG _ 5.9mm. 1000 pF 100pF 100 pF BT05AG BT013 39nH 3. 100pF 100pF 2pF B B B 3.3nH 1pF 4. Typical Performance BeRex ● website: www.berex.com ● email: sales@berex.com 7 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark o f BeRex. All other trademarks are the property of their respective owners. © 2010 BeRex Rev. C BT05AG 5-4000 MHz Wideband Drive Amplifier BeRex ● website: www.berex.com ● email: sales@berex.com 8 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark o f BeRex. All other trademarks are the property of their respective owners. © 2010 BeRex Rev. C BT05AG 5-4000 MHz Wideband Drive Amplifier Application Circuit: 2450MHz Schematic Diagram C1 C2 C3 BOM +5V Tolerance ±5% ±5% ±20% ±5% ±5% ±5% ±5% L1 RFin C4 BT05AG C5 C6 RFout C1 C2 C3 C4 C5 C6 L1 100pF 1000pF 10uF 100pF 100pF 1.2pF 39nH Note: 10uF 1. 2. PCB: 31mil thick FR4 Distance between the center of the shunt cap (C6) and the input pin of BT05AG _ 0.5mm. 1000 pF 100pF 100 pF BT05AG BT013 39nH 100pF 1.2pF B B B 100pF Typical Performance BeRex ● website: www.berex.com ● email: sales@berex.com 9 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark o f BeRex. All other trademarks are the property of their respective owners. © 2010 BeRex Rev. C BT05AG 5-4000 MHz Wideband Drive Amplifier BeRex ● website: www.berex.com ● email: sales@berex.com 10 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark o f BeRex. All other trademarks are the property of their respective owners. © 2010 BeRex Rev. C BT05AG 5-4000 MHz Wideband Drive Amplifier Application Circuit: 3500MHz Schematic Diagram C1 C2 C3 BOM +5V Tolerance ±5% ±5% ±20% ±5% ±5% ±5% ±5% ±5% ±5% L1 RFin C4 L2 BT05AG RFout C7 C5 C6 C1 C2 C3 C4 C5 C6 C7 L1 L2 100pF 1000pF 10uF 18pF 18pF 0.75pF 0.5pF 33nH 2.7nH Note: 10uF 1. 2. PCB: 31mil thick FR4 Distance between the center of the series inductor(L2) and the input pin of BT05AG _ 2.0mm. Distance between the center of the shunt cap(C6) and the input pin of BT05AG _ 0.5mm. Distance between the center of the shunt cap(C7) and the output pin of BT05AG _ 10.0mm. 1000 pF 100pF 100 pF 2.7nH 18pF 0.75pF BT05AG BT013 33nH 3. 18pF 0.5pF B B B 4. Typical Performance BeRex ● website: www.berex.com ● email: sales@berex.com 11 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark o f BeRex. All other trademarks are the property of their respective owners. © 2010 BeRex Rev. C BT05AG 5-4000 MHz Wideband Drive Amplifier BeRex ● website: www.berex.com ● email: sales@berex.com 12 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark o f BeRex. All other trademarks are the property of their respective owners. © 2010 BeRex Rev. C BT05AG 5-4000 MHz Wideband Drive Amplifier Package Outline Dimension Suggested PCB Land Pattern and PAD Layout PCB Land Pattern 0.40 1.30 0.40 PCB Mounting Ø0.40 0.40 0.75 1.20 1.20 0.45 1.20 1.20 1.50 1.00 0.65 0.35 2.80 2.15 0.50 Note : All dimension _ millimeters PCB lay out _ on BeRex website BeRex ● website: www.berex.com ● email: sales@berex.com 13 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark o f BeRex. All other trademarks are the property of their respective owners. © 2010 BeRex Rev. C BT05AG 5-4000 MHz Wideband Drive Amplifier Tape & Reel SOT89 Packaging information: Tape Width (mm): 12 Reel Size (inches): 7 Device Cavity Pitch (mm): 8 Devices Per Reel: 1000 Lead plating finish 100% Tin Matte finish (All BeRex products undergoes a 1 hour, 150 degree C, Anneal bake to eliminate thin whisker growth concerns.) MSL / ESD Rating ESD Rating: Value: Test: Standard: Class 1B Passes