User's Guide
SLUUB51 – August 2014
User's Guide for WCSP Packaged bq25100 250-mA
Battery Charger EVM
The bq25100 evaluation module (EVM) on PWR654 PCB is a complete charger module for evaluating a
compact, flexible, high-efficiency, USB-friendly, linear charge management solution for single-cell, Li-ion
and Li-polymer batteries used in wearables and low-power portable applications.
1
2
3
Contents
Introduction ................................................................................................................... 2
1.1
bq25100 IC Features ............................................................................................... 2
1.2
bq25100 EVM - 654 Features ..................................................................................... 2
1.3
Schematic ............................................................................................................ 2
1.4
I/O Description ...................................................................................................... 3
1.5
Test Points ........................................................................................................... 3
1.6
Control and Key Parameters Setting ............................................................................. 4
1.7
Recommended Operating Conditions ............................................................................ 4
Test Summary ................................................................................................................ 5
2.1
Definitions ............................................................................................................ 5
2.2
Recommended Test Equipment .................................................................................. 5
2.3
Recommended Test Equipment Setup .......................................................................... 6
2.4
Recommended Test Procedure ................................................................................... 7
Bill of Materials and Board Layout ......................................................................................... 9
3.1
Bill of Materials ...................................................................................................... 9
3.2
Board Layout ....................................................................................................... 10
List of Figures
1
bq25100EVM (PWR654) Schematic ...................................................................................... 2
2
BAT Load (PR1010) Schematic
3
4
5
6
7
8
9
10
........................................................................................... 5
Test Setup for bq25100 EVM (PWR654) ................................................................................. 6
Top Overlay ................................................................................................................. 10
Top Solder Mask .......................................................................................................... 10
Top Layer.................................................................................................................... 11
Bottom Layer ................................................................................................................ 11
Bottom Solder Mask ....................................................................................................... 12
Drill Drawing ................................................................................................................ 12
Board Dimensions .......................................................................................................... 13
SLUUB51 – August 2014
Submit Documentation Feedback
User's Guide for WCSP Packaged bq25100 250-mA Battery Charger EVM
Copyright © 2014, Texas Instruments Incorporated
1
Introduction
www.ti.com
1
Introduction
1.1
bq25100 IC Features
The bq2510x series of devices are highly integrated Li-Ion and Li-Pol linear chargers targeted at spacelimited portable applications. It integrates input current sensing, high-accuracy current and voltage
regulation, and charge termination into a chipscale package. Key integrated circuit (IC) features include:
• Extremely small package size 0.9 mm x 1.6 mm
• Programmable charge current from below 10 mA to 250 mA
• Programmable termination current down to 1 mA
• Extremely low battery leakage current < 1 µA
• 30 V maximum input voltage rating
For details, see the bq2510x data sheet (SLUSBV8).
1.2
bq25100 EVM - 654 Features
The bq25100 EVM on PWR654 PCB is a complete charger module for evaluating compact, flexible, highefficiency, USB-friendly, linear battery charge solution for single-cell, Li-ion and Li-polymer batterypowered systems used in wearables and low-power portable applications. Key EVM features include:
• Programmable charge current, pre_charge/termination current
• IN operating range of 4.45 to 6.45 V
• LED indication for status signals
• Test points for key signals available for testing purposes; easy probe hook-up
1.3
Schematic
J2
TP1
IN
R9
DNP
DNI
J5
TP4
4.45 V to 6.45V
R8
0
U1
A2
DNPC3
DNI
GND
C1
1µF
TP2
ISET
IN
B2
ISET
J1
R1
453
GND
C1
TP3
R10
DNP
DNI
R2
TS
PRETERM
VSS
J4
OUT (BAT+)
GND (BAT-)
TS
GND
A1
TP5
B1
TP6
C2
1
2
3
4
OUT (BAT +)
GND (BAT -)
TS
GND
BQ25100YFP
PRETERM/CHG
R3
499
J3
OUT
1
2
3
IN
R5
1.00k
D1
J9
R6
1.00k
C2DNPC4 DNPC5
1µF DNI
DNI
J6
TS GND
DNPC6
DNI
R4
Green
50k ohm
1
2
3
20k ohm
J7
R7
PRETERM
J8
50k ohm
CHG
J10
GND
GND
RISET
GND
Figure 1. bq25100EVM (PWR654) Schematic
2
User's Guide for WCSP Packaged bq25100 250-mA Battery Charger EVM
Copyright © 2014, Texas Instruments Incorporated
SLUUB51 – August 2014
Submit Documentation Feedback
Introduction
www.ti.com
1.4
1.5
I/O Description
Header or Terminal Block
Description
J1-IN/GND
Terminal block for connecting IN and GND pins to input supply
positive and negative connections
J2-IN
Headers for extra connections to IN pin
J3-GND
Headers for GND
J4-OUT/TS
Terminal block for connecting BAT and GND pins to battery positive
and negative connections
J5-OUT
Headers for extra connections to OUT pin
J6-GND
Headers for connecting GND pin to battery or measurement device
negative connection
J7-Preterm/CHG
Headers for connecting PRETERM pin to external Preterm resistor or
external LED for /CHG
J8-ISET
Headers for connecting ISET pin to external resistor or GND
J9-TS/GND
Headers for connecting TS pin to battery NTC or ground connections
J10-GND
Headers for connecting GND pin to battery or measurement device
negative connection
Test Points
SLUUB51 – August 2014
Submit Documentation Feedback
Test Point
Description
TP1
Test point connecting to IN pin
TP2
Test point connecting to ISET pin
TP3
Test point connecting to PRETERM pin
TP4
Test point connecting to OUT pin
TP5
Test point connecting to TS pin
TP6
Test point connecting to VSS pin
User's Guide for WCSP Packaged bq25100 250-mA Battery Charger EVM
Copyright © 2014, Texas Instruments Incorporated
3
Introduction
1.6
www.ti.com
Control and Key Parameters Setting
IC
1.7
Jumper
Description
Default Factory Setting
All
JP1
Connects IN and GND to the positive and negative connection
of the input power source
All
JP2
Not used
N/A
All
JP3
Not used
N/A
All
JP4
Connects BAT and GND pins to battery positive and negative
connections
N/A
All
JP5
Not used
N/A
All
JP6
Not used
N/A
BQ25100/100A
JP7
/100H/100L
1-2: (PRETERM/CHG = PRETERM): Connects to external
PRETERM resistor to program the pre_charge/termination
percentage
2-3: (PRETERM/CHG = /CHG): Connects to external LED to
indicate the charge status
1-2 (PRETERM/CHG = PRETERM)
BQ25101/101H JP7
1-2: (PRETERM/CHG = PRETERM): Connects to external
PRETERM resistor to program the pre_charge/termination
percentage
2-3: (PRETERM/CHG = /CHG): Connects to external LED to
indicate the charge status
2-3 (PRETERM/CHG = /CHG)
All
JP8
Connects the external resistor to ISET pin to program the
charge current
Installed
All
J9
1-2: (TS = TS voltage): Connects to programmable voltage to
mimic battery NTC
2-3: (TS = GND): Connects to VSS to disable charging
1-2 (TS = TS voltage)
All
J10
Not used
N/A
N/A
Recommended Operating Conditions
MIN
4
VIN
Supply voltage
Operating input voltage from AC adapter (No charging for
VIN < VINDPM threshold = 4.4V)
IIN(MAX)
Supply current
ICHRG(MAX)
Max fast charge
current
TJ
Operating junction temperature range
RPRETERM
Programs pre_charge and termination current thresholds
RISET
Fast-charge current programming resistor
RTS
10 k NTC thermistor range without entering BAT_EN or TTDM
1.66
TYP
MAX UNIT
4.45
6.45
V
Maximum input current limit
0.100
0.25
A
Maximum charging current limit
0.100
0.25
A
0
125
°C
3
30
kΩ
0.54
13.5
kΩ
258
kΩ
User's Guide for WCSP Packaged bq25100 250-mA Battery Charger EVM
Copyright © 2014, Texas Instruments Incorporated
SLUUB51 – August 2014
Submit Documentation Feedback
Test Summary
www.ti.com
2
Test Summary
This procedure describes one test configuration of the bq25100EVM-654 evaluation board for bench
evaluation.
2.1
Definitions
The following naming conventions are used;
VXXX :
LOAD#:
V(TPyyy):
V(Jxx):
V(XXX, YYY):
I(JXX(YYY)):
Jxx(BBB):
JPx ON :
JPx OFF:
JPx (-YY-)
Measure: → A, B
Observe → A, B
External voltage supply name (VIN, VUSB)
External load name
Voltage at internal test point TPyyy. For example, V(TP12) means the voltage at
TP12.
Voltage at header Jxx
Voltage across point XXX and YYY
Current going out from the YYY terminal of header XX
Terminal or pin BBB of header xx
Internal jumper Jxx terminals are shorted
Internal jumper Jxx terminals are open
ON: Internal jumper Jxx adjacent terminals marked as YY are shorted
Check specified parameters A, B. If measured values are not within specified limits,
the unit under test has failed.
Observe if A, B occur. If they do not occur, the unit under test has failed.
Assembly drawings have locations for jumpers, test points, and individual components.
2.2
Recommended Test Equipment
2.2.1
Power Supplies
1. Power supply number 1 (PS#1): a power supply capable of supplying 5 V at 1 A is required
2. Power supply number 2 (PS#2): a power supply capable of supplying 5 V at 1 A is required
2.2.2
Load Number 1 Between BAT and GND
Testing with an actual battery is the best way to verify operation in the system. If a battery is unavailable,
then a sourcemeter like a Keithley 2420, capable of both sourcing and sinking current, or a circuit similar
to the one shown in Figure 2 can simulate a battery when connected to PS#2.
Figure 2. BAT Load (PR1010) Schematic
SLUUB51 – August 2014
Submit Documentation Feedback
User's Guide for WCSP Packaged bq25100 250-mA Battery Charger EVM
Copyright © 2014, Texas Instruments Incorporated
5
Test Summary
2.2.3
www.ti.com
Meters
Three equivalent voltage meters (VM#x) and two equivalent current meters (CM#x) are required. The
current meters must be able to measure at least 0.5-A current.
2.3
Recommended Test Equipment Setup
1. For all power connections, use short, twisted-pair wires of appropriate gauge wire for the amount of the
current.
2. Set PS#1 for 5 V ±100 mV DC, 1-A current limit and then turn off supply.
3. Connect the positive output of PS#1 through a current meter (CM#2) to IN of J1 or J2 and negative
output to GND of J1 or J3.
4. Connect a voltage meter (VM#1) across J2 and J3 or TP1 (IN) and TP6 (GND).
5. If BAT_Load (PR1010), as shown in Figure 2, is used, connect PS#2 set to approximately 3.1 V to the
input side (PS#2±) of BAT_Load (PR1010), then turn off PS#2.
CAUTION
The heat sinks on PR1010 will be very hot.
6. Connect the output side of the battery or BAT_Load (PR1010) in series with CM#1 to J5 and J6 (BAT,
GND). Ensure that VM#2 is connected across J5 or TP4 and J6 or TP6 (BAT, GND).
7. Connect a DMM (VM#3) capable of measuring both voltage and resistance across TP2(ISET) and
TP6(GND) or J10(GND).
8. Ensure jumpers are at the default factory settings per Section 1.6.
9. After the preceding steps are accomplished, the test setup for bq25100EVM-654 is as shown in
Figure 3.
Figure 3. Test Setup for bq25100 EVM (PWR654)
6
User's Guide for WCSP Packaged bq25100 250-mA Battery Charger EVM
Copyright © 2014, Texas Instruments Incorporated
SLUUB51 – August 2014
Submit Documentation Feedback
Test Summary
www.ti.com
2.4
Recommended Test Procedure
The following test procedure may be useful for evaluating the charger IC outside of a real system, if no
battery is available to connect to the output and a circuit similar to PR1010 is used to simulate a battery.
2.4.1
Test Setup
1. Ensure that the Section 2.3 steps are followed.
2. Set VM#3 DMM to measure resistance.
3. Turn the potentiometer R2 until:
Measure on VM#3 → R[TP2(ISET), TP6(GND)] = 1.3 kΩ–1.4 kΩ
4. Move the positive side of VM#3 DMM to TP5 (TS).
5. Turn the potentiometer R7 until:
Measure on VM#3 → R[TP5(TS), TP6(GND)] = 9 kΩ–11 kΩ
6. Move the positive side of VM#3 DMM to TP3(PRETERM).
7. Turn the potentiometer R4 until
Measure on VM#3 → R[TP3(PRETERM), TP6(GND)] = 5.5 kΩ–6.5 kΩ
8. Move the positive side of VM#3 DMM to TP2 (ISET).
9. Set VM#3 DMM to measure voltage.
10. Move the shunt on J9 (TS) to GND.
11. Enable PS#1 and PS#2.
12. Measure on VM#3 → V[TP2(ISET), TP6(GND)] < 0.1 V
Measure on CM#1 → ICHRG ≤ 0–5 mA
Measure on CM#2 → IIN ≤ 10 mA
13. Disable PS#1 and PS#2.
14. Move the shunt on J9 (TS) to pin1 of the jumper.
15. Enable PS#1 and PS#2.
16. Adjust PS#2 so that the voltage measured by VM#2, across BAT and GND, measures 3.0 V–3.5 V.
17. Adjust the PS#1 so that VM#1 still reads 5.0 V ±100 mV
Measure on VM#3 → V[TP2(ISET), TP6(GND)] = 1.45–1.55 V
Measure on CM#1 → ICHRG = 90–100 mA
Measure on CM#2 → IIN = 93–113 mA
18. Disable PS#1 and PS#2.
19. Disable all power supplies and remove all connections being careful not to disturb the potentiometer
settings.
SLUUB51 – August 2014
Submit Documentation Feedback
User's Guide for WCSP Packaged bq25100 250-mA Battery Charger EVM
Copyright © 2014, Texas Instruments Incorporated
7
Test Summary
www.ti.com
2.4.2
Helpful Hints
1. The leads and cables to the various power supplies have resistance. The current meters also have
series resistance. Therefore, voltmeters must be used to measure the voltage as close to the IC pins
as possible instead of relying on each supply's digital measurement.
2. When using a sourcemeter as your battery simulator, it is highly recommended to configure the
sourcemeter for 4-wire sensing, eliminating the need for a separate voltmeter to measure the voltage
at the OUT pin.
3. To observe the taper current as the battery voltage approaches the set regulation voltage, allow the
battery to charge, or if using BAT_Load (PR1010), slowly increase the PS#2 voltage powering
BAT_Load (PR1010). Use VM#2 across OUT and GND to measure the battery voltage seen by the IC.
4. For precise measurements of charge current and battery regulation near termination, remove the
current meter in series with the battery or battery simulator. An alternate method for measuring charge
current is to either use an oscilloscope with hall effect current probe or place a 1% or better, thermally
capable (for example, 0.010 Ω in 1210 or larger footprint) resistor in series between the OUT or GND
pins and battery and measure the voltage across that resistor. PR1010 resistor R3 is such a resistor.
5. To observe the VINDPM function, lower the current limit on PS#1 (with 3.1 V < VBAT < 4.2 V).
8
User's Guide for WCSP Packaged bq25100 250-mA Battery Charger EVM
Copyright © 2014, Texas Instruments Incorporated
SLUUB51 – August 2014
Submit Documentation Feedback
Bill of Materials and Board Layout
www.ti.com
3
Bill of Materials and Board Layout
3.1
Bill of Materials
Table 1. Bill of Materials – PWR654A
Designator
Qty
Value
Description
Package Reference
Part Number
Manufacturer
C1
1
1uF
CAP, CERM, 1uF, 35V, +/-10%, JB, 0402
0402
C1005JB1V105K050BC
TDK
C2
1
1uF
CAP, CERM, 1uF, 10V, +/-10%, X5R, 0402
0402
GRM155R61A105KE15D
MuRata
D1
1
Green
LED, Green, SMD
1.6x0.8x0.8mm
LTST-C190GKT
Lite-On
J1
1
2x1
Conn Term Block, 2POS, 3.81mm, TH
PhoenixConact_1727010
1727010
Phoenix Contact
J2, J3, J5, J6, J8,
J10
6
Header, TH, 100mil, 2x1, Gold plated, 230 mil above
insulator
TSW-102-07-G-S
TSW-102-07-G-S
Samtec, Inc.
J4
1
Terminal Block, 6A, 3.5mm Pitch, 4-Pos, TH
14x8.2x6.5mm
ED555/4DS
On-Shore Technology
J7, J9
2
Header, TH, 100mil, 3x1, Gold plated, 230 mil above
insulator
TSW-103-07-G-S
TSW-103-07-G-S
Samtec, Inc.
LBL1
1
Thermal Transfer Printable Labels, 0.650" W x 0.200" H 10,000 per roll
PCB Label 0.650"H x
0.200"W
THT-14-423-10
Brady
R1
1
453
RES, 453 ohm, 1%, 0.063W, 0402
0402
CRCW0402453RFKED
Vishay-Dale
R2
1
20k ohm
TRIMMER, 20K, 0.5W, TH
9.5x10x4.8mm
3296Y-1-203LF
Bourns
R3
1
499
RES, 499 ohm, 1%, 0.063W, 0402
0402
CRCW0402499RFKED
Vishay-Dale
R4, R7
2
TRIMMER, 50k ohm, 0.5W, TH
9.5x10x4.8mm
3296Y-1-503LF
Bourns
R5, R6
2
1.00k
RES, 1.00k ohm, 1%, 0.063W, 0402
0402
CRCW04021K00FKED
Vishay-Dale
R8
1
0
RES, 0 ohm, 5%, 0.1W, 0603
0603
CRCW06030000Z0EA
Vishay-Dale
SH-JP1, SH-JP2,
SH-JP3
3
1x2
Shunt, 100mil, Gold plated, Black
Shunt
969102-0000-DA
3M
TP1, TP2, TP3,
TP4, TP5, TP6
6
Blue
Test Point, TH, Compact, Blue
Keystone5122
5122
Keystone
U1
1
250 mA Single-Input, Single Cell Li-Ion Battery Chargers,
YFP0006AFAV
YFP0006AFAV
BQ25100YFP
Texas Instruments
C3, C4, C5
0
1uF
CAP, CERM, 1uF, 35V, +/-10%, X5R, 0603
0603
GMK107BJ105KA-T
Taiyo Yuden
C6
0
0.01uF
CAP, CERM, 0.01uF, 100V, +/-5%, X7R, 0603
0603
06031C103JAT2A
AVX
R9
0
0
RES, 0 ohm, 5%, 0.1W, 0603
0603
CRCW06030000Z0EA
Vishay-Dale
R10
0
RES, 1.00k ohm, 1%, 0.063W, 0402
0402
CRCW04021K00FKED
Vishay-Dale
SLUUB51 – August 2014
Submit Documentation Feedback
Alternate Part
Number
Alternate
Manufacturer
-
-
SNT-100-BK-G
Samtec
None
User's Guide for WCSP Packaged bq25100 250-mA Battery Charger EVM
Copyright © 2014, Texas Instruments Incorporated
9
Bill of Materials and Board Layout
3.2
www.ti.com
Board Layout
Figure 4. Top Overlay
Figure 5. Top Solder Mask
10
User's Guide for WCSP Packaged bq25100 250-mA Battery Charger EVM
Copyright © 2014, Texas Instruments Incorporated
SLUUB51 – August 2014
Submit Documentation Feedback
Bill of Materials and Board Layout
www.ti.com
Figure 6. Top Layer
Figure 7. Bottom Layer
SLUUB51 – August 2014
Submit Documentation Feedback
User's Guide for WCSP Packaged bq25100 250-mA Battery Charger EVM
Copyright © 2014, Texas Instruments Incorporated
11
Bill of Materials and Board Layout
www.ti.com
Figure 8. Bottom Solder Mask
Figure 9. Drill Drawing
12
User's Guide for WCSP Packaged bq25100 250-mA Battery Charger EVM
Copyright © 2014, Texas Instruments Incorporated
SLUUB51 – August 2014
Submit Documentation Feedback
Bill of Materials and Board Layout
www.ti.com
Figure 10. Board Dimensions
SLUUB51 – August 2014
Submit Documentation Feedback
User's Guide for WCSP Packaged bq25100 250-mA Battery Charger EVM
Copyright © 2014, Texas Instruments Incorporated
13
ADDITIONAL TERMS AND CONDITIONS, WARNINGS, RESTRICTIONS, AND DISCLAIMERS FOR
EVALUATION MODULES
Texas Instruments Incorporated (TI) markets, sells, and loans all evaluation boards, kits, and/or modules (EVMs) pursuant to, and user
expressly acknowledges, represents, and agrees, and takes sole responsibility and risk with respect to, the following:
1.
User agrees and acknowledges that EVMs are intended to be handled and used for feasibility evaluation only in laboratory and/or
development environments. Notwithstanding the foregoing, in certain instances, TI makes certain EVMs available to users that do not
handle and use EVMs solely for feasibility evaluation only in laboratory and/or development environments, but may use EVMs in a
hobbyist environment. All EVMs made available to hobbyist users are FCC certified, as applicable. Hobbyist users acknowledge, agree,
and shall comply with all applicable terms, conditions, warnings, and restrictions in this document and are subject to the disclaimer and
indemnity provisions included in this document.
2. Unless otherwise indicated, EVMs are not finished products and not intended for consumer use. EVMs are intended solely for use by
technically qualified electronics experts who are familiar with the dangers and application risks associated with handling electrical
mechanical components, systems, and subsystems.
3. User agrees that EVMs shall not be used as, or incorporated into, all or any part of a finished product.
4. User agrees and acknowledges that certain EVMs may not be designed or manufactured by TI.
5. User must read the user's guide and all other documentation accompanying EVMs, including without limitation any warning or
restriction notices, prior to handling and/or using EVMs. Such notices contain important safety information related to, for example,
temperatures and voltages. For additional information on TI's environmental and/or safety programs, please visit www.ti.com/esh or
contact TI.
6. User assumes all responsibility, obligation, and any corresponding liability for proper and safe handling and use of EVMs.
7. Should any EVM not meet the specifications indicated in the user’s guide or other documentation accompanying such EVM, the EVM
may be returned to TI within 30 days from the date of delivery for a full refund. THE FOREGOING LIMITED WARRANTY IS THE
EXCLUSIVE WARRANTY MADE BY TI TO USER AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR
STATUTORY, INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. TI SHALL
NOT BE LIABLE TO USER FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES RELATED TO THE
HANDLING OR USE OF ANY EVM.
8. No license is granted under any patent right or other intellectual property right of TI covering or relating to any machine, process, or
combination in which EVMs might be or are used. TI currently deals with a variety of customers, and therefore TI’s arrangement with
the user is not exclusive. TI assumes no liability for applications assistance, customer product design, software performance, or
infringement of patents or services with respect to the handling or use of EVMs.
9. User assumes sole responsibility to determine whether EVMs may be subject to any applicable federal, state, or local laws and
regulatory requirements (including but not limited to U.S. Food and Drug Administration regulations, if applicable) related to its handling
and use of EVMs and, if applicable, compliance in all respects with such laws and regulations.
10. User has sole responsibility to ensure the safety of any activities to be conducted by it and its employees, affiliates, contractors or
designees, with respect to handling and using EVMs. Further, user is responsible to ensure that any interfaces (electronic and/or
mechanical) between EVMs and any human body are designed with suitable isolation and means to safely limit accessible leakage
currents to minimize the risk of electrical shock hazard.
11. User shall employ reasonable safeguards to ensure that user’s use of EVMs will not result in any property damage, injury or death,
even if EVMs should fail to perform as described or expected.
12. User shall be solely responsible for proper disposal and recycling of EVMs consistent with all applicable federal, state, and local
requirements.
Certain Instructions. User shall operate EVMs within TI’s recommended specifications and environmental considerations per the user’s
guide, accompanying documentation, and any other applicable requirements. Exceeding the specified ratings (including but not limited to
input and output voltage, current, power, and environmental ranges) for EVMs may cause property damage, personal injury or death. If
there are questions concerning these ratings, user should contact a TI field representative prior to connecting interface electronics including
input power and intended loads. Any loads applied outside of the specified output range may result in unintended and/or inaccurate
operation and/or possible permanent damage to the EVM and/or interface electronics. Please consult the applicable EVM user's guide prior
to connecting any load to the EVM output. If there is uncertainty as to the load specification, please contact a TI field representative. During
normal operation, some circuit components may have case temperatures greater than 60°C as long as the input and output are maintained
at a normal ambient operating temperature. These components include but are not limited to linear regulators, switching transistors, pass
transistors, and current sense resistors which can be identified using EVMs’ schematics located in the applicable EVM user's guide. When
placing measurement probes near EVMs during normal operation, please be aware that EVMs may become very warm. As with all
electronic evaluation tools, only qualified personnel knowledgeable in electronic measurement and diagnostics normally found in
development environments should use EVMs.
Agreement to Defend, Indemnify and Hold Harmless. User agrees to defend, indemnify, and hold TI, its directors, officers, employees,
agents, representatives, affiliates, licensors and their representatives harmless from and against any and all claims, damages, losses,
expenses, costs and liabilities (collectively, "Claims") arising out of, or in connection with, any handling and/or use of EVMs. User’s
indemnity shall apply whether Claims arise under law of tort or contract or any other legal theory, and even if EVMs fail to perform as
described or expected.
Safety-Critical or Life-Critical Applications. If user intends to use EVMs in evaluations of safety critical applications (such as life support),
and a failure of a TI product considered for purchase by user for use in user’s product would reasonably be expected to cause severe
personal injury or death such as devices which are classified as FDA Class III or similar classification, then user must specifically notify TI
of such intent and enter into a separate Assurance and Indemnity Agreement.
RADIO FREQUENCY REGULATORY COMPLIANCE INFORMATION FOR EVALUATION MODULES
Texas Instruments Incorporated (TI) evaluation boards, kits, and/or modules (EVMs) and/or accompanying hardware that is marketed, sold,
or loaned to users may or may not be subject to radio frequency regulations in specific countries.
General Statement for EVMs Not Including a Radio
For EVMs not including a radio and not subject to the U.S. Federal Communications Commission (FCC) or Industry Canada (IC)
regulations, TI intends EVMs to be used only for engineering development, demonstration, or evaluation purposes. EVMs are not finished
products typically fit for general consumer use. EVMs may nonetheless generate, use, or radiate radio frequency energy, but have not been
tested for compliance with the limits of computing devices pursuant to part 15 of FCC or the ICES-003 rules. Operation of such EVMs may
cause interference with radio communications, in which case the user at his own expense will be required to take whatever measures may
be required to correct this interference.
General Statement for EVMs including a radio
User Power/Frequency Use Obligations: For EVMs including a radio, the radio included in such EVMs is intended for development and/or
professional use only in legally allocated frequency and power limits. Any use of radio frequencies and/or power availability in such EVMs
and their development application(s) must comply with local laws governing radio spectrum allocation and power limits for such EVMs. It is
the user’s sole responsibility to only operate this radio in legally acceptable frequency space and within legally mandated power limitations.
Any exceptions to this are strictly prohibited and unauthorized by TI unless user has obtained appropriate experimental and/or development
licenses from local regulatory authorities, which is the sole responsibility of the user, including its acceptable authorization.
U.S. Federal Communications Commission Compliance
For EVMs Annotated as FCC – FEDERAL COMMUNICATIONS COMMISSION Part 15 Compliant
Caution
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications could void the user's authority to operate the equipment.
FCC Interference Statement for Class A EVM devices
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the interference at its own expense.
FCC Interference Statement for Class B EVM devices
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Industry Canada Compliance (English)
For EVMs Annotated as IC – INDUSTRY CANADA Compliant:
This Class A or B digital apparatus complies with Canadian ICES-003.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the
equipment.
Concerning EVMs Including Radio Transmitters
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired
operation of the device.
Concerning EVMs Including Detachable Antennas
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain
approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should
be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
This radio transmitter has been approved by Industry Canada to operate with the antenna types listed in the user guide with the maximum
permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain
greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
Canada Industry Canada Compliance (French)
Cet appareil numérique de la classe A ou B est conforme à la norme NMB-003 du Canada
Les changements ou les modifications pas expressément approuvés par la partie responsable de la conformité ont pu vider l’autorité de
l'utilisateur pour actionner l'équipement.
Concernant les EVMs avec appareils radio
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est
autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout
brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Concernant les EVMs avec antennes détachables
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain
maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à
l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente
(p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante.
Le présent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés dans le manuel
d’usage et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus dans
cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2014, Texas Instruments Incorporated
spacer
Important Notice for Users of EVMs Considered “Radio Frequency Products” in Japan
EVMs entering Japan are NOT certified by TI as conforming to Technical Regulations of Radio Law of Japan.
If user uses EVMs in Japan, user is required by Radio Law of Japan to follow the instructions below with respect to EVMs:
1.
2.
3.
Use EVMs in a shielded room or any other test facility as defined in the notification #173 issued by Ministry of Internal Affairs and
Communications on March 28, 2006, based on Sub-section 1.1 of Article 6 of the Ministry’s Rule for Enforcement of Radio Law of
Japan,
Use EVMs only after user obtains the license of Test Radio Station as provided in Radio Law of Japan with respect to EVMs, or
Use of EVMs only after user obtains the Technical Regulations Conformity Certification as provided in Radio Law of Japan with respect
to EVMs. Also, do not transfer EVMs, unless user gives the same notice above to the transferee. Please note that if user does not
follow the instructions above, user will be subject to penalties of Radio Law of Japan.
http://www.tij.co.jp
【無線電波を送信する製品の開発キットをお使いになる際の注意事項】 本開発キットは技術基準適合証明を受けておりません。 本製品の
ご使用に際しては、電波法遵守のため、以下のいずれかの措置を取っていただく必要がありますのでご注意ください。
1.
2.
3.
電波法施行規則第6条第1項第1号に基づく平成18年3月28日総務省告示第173号で定められた電波暗室等の試験設備でご使用いただく。
実験局の免許を取得後ご使用いただく。
技術基準適合証明を取得後ご使用いただく。。
なお、本製品は、上記の「ご使用にあたっての注意」を譲渡先、移転先に通知しない限り、譲渡、移転できないものとします
上記を遵守頂けない場合は、電波法の罰則が適用される可能性があることをご留意ください。
日本テキサス・インスツルメンツ株式会社
東京都新宿区西新宿6丁目24番1号
西新宿三井ビル
http://www.tij.co.jp
Texas Instruments Japan Limited
(address) 24-1, Nishi-Shinjuku 6 chome, Shinjuku-ku, Tokyo, Japan
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2014, Texas Instruments Incorporated