User's Guide
SLUUA15 – October 2012
bq34z110EVM Wide-Range Impedance Track™ Enabled
Fuel Gauge Solution for Lead-Acid Batteries
This evaluation module (EVM) is a complete evaluation system for the bq34z110 wide-range fuel gauge
for lead-acid chemistries when combined with an EV2300 USB adapter and Windows®-based PC
software, downloadable from the TI.com website.
The circuit module includes one bq34z110 integrated circuit (IC) and all other components necessary to
monitor and predict capacity in 2 or more series cell Lead Acid battery packs. The circuit module connects
directly across the battery.
With the EV2300 interface adapter and software, it is possible to read the bq34z110 data registers,
program the chip for different pack configurations, log cycling data for further evaluation, and evaluate the
overall functionality of the bq34z110 solution under different charge and discharge conditions.
1
2
3
4
5
Contents
Features ...................................................................................................................... 2
1.1
Kit Contents ......................................................................................................... 2
1.2
Ordering Information ............................................................................................... 2
bq34z110 Device-Based Circuit Module ................................................................................. 3
2.1
Circuit Module Connections ...................................................................................... 3
2.2
Pin Descriptions .................................................................................................... 3
bq34z110 Circuit Module .................................................................................................. 3
3.1
Choosing SingleCell (1S) or MultiCell operation ............................................................... 3
3.2
Choosing Maximum MultiCell Battery Voltage ................................................................. 3
3.3
Choosing the LED configuration ................................................................................. 4
3.4
Choosing the ALERT configuration .............................................................................. 4
Circuit Module Physical Layouts, Schematic, and Bill of Materials ................................................... 4
4.1
Board Layout ....................................................................................................... 4
4.2
Schematic ........................................................................................................... 8
4.3
bq34z110 Circuit Module Performance Specification Summary ........................................... 11
EVM Hardware and Software Setup .................................................................................... 11
5.1
System Requirements ........................................................................................... 11
5.2
Software Installation .............................................................................................. 11
5.3
Troubleshooting Unexpected Dialog Boxes ................................................................... 11
5.4
Hardware Connection ............................................................................................ 11
5.5
Operation .......................................................................................................... 13
5.6
Calibration Screen ................................................................................................ 16
5.7
I2C Pro (Advanced) Screen ..................................................................................... 17
5.8
Send HDQ Screen ................................................................................................ 18
5.9
bqChem ............................................................................................................ 19
5.10 Related Documentation from Texas Instruments ............................................................ 19
List of Figures
1
bq34z110EVM Layout (Silkscreen) ....................................................................................... 4
2
bq34z110EVM Top Assembly ............................................................................................. 5
3
bq34z110EVM Top Layer .................................................................................................. 5
Impedance Track is a trademark of Texas Instruments, Inc..
Windows is a registered trademark of Microsoft Corporation.
SLUUA15 – October 2012
Submit Documentation Feedback
bq34z110EVM Wide-Range Impedance Track™ Enabled Fuel Gauge
Solution for Lead-Acid Batteries
Copyright © 2012, Texas Instruments Incorporated
1
Features
www.ti.com
4
bq34z110EVM Inner Layer 1 .............................................................................................. 6
5
bq34z110EVM Inner Layer 2 .............................................................................................. 6
6
bq34z110EVM Bottom Layer .............................................................................................. 7
7
bq34z110EVM Schematic
8
9
10
11
12
13
14
................................................................................................. 8
bq34z110 Circuit Module Connection to Cells and System Load and Charger ................................... 12
Data RAM Screen ......................................................................................................... 14
Data Flash Screen, Gas Gauging Class ............................................................................... 15
Calibration Screen ......................................................................................................... 16
I2C Pro (Advanced) Screen .............................................................................................. 17
Send HDQ Screen ........................................................................................................ 18
bqChem Screen ........................................................................................................... 19
List of Tables
1
1
Ordering Information ........................................................................................................ 2
2
bq34z110EVM Bill of Materials............................................................................................ 9
3
Performance Specification Summary ................................................................................... 11
4
Circuit Module to EV2300 or EV2400 Connections ................................................................... 12
Features
•
•
•
1.1
Kit Contents
•
•
1.2
Complete evaluation system for the bq34z110 advanced gas gauge with Impedance Track™
technology.
Populated circuit module for quick setup
Link to software allowing data logging for system analysis
bq34z110 circuit module
Support documentation
Ordering Information
Table 1. Ordering Information
2
EVM Part Number
Chemistry
Configuration
Capacity
bq34z110EVM
Lead Acid
3 V–65 V
Any
bq34z110EVM Wide-Range Impedance Track™ Enabled Fuel Gauge
Solution for Lead-Acid Batteries
Copyright © 2012, Texas Instruments Incorporated
SLUUA15 – October 2012
Submit Documentation Feedback
bq34z110 Device-Based Circuit Module
www.ti.com
2
bq34z110 Device-Based Circuit Module
The bq34z110-based circuit module is a complete and compact example solution of a bq34z110 fuel
gauge solution for Lead Acid packs. The circuit module incorporates a bq34z110 fuel gauge IC and
various option components and jumpers necessary for evaluation under various battery voltage, LED, and
ALERT signal configurations.
2.1
Circuit Module Connections
Contacts on the circuit module provide the following connections:
• Direct connection to BAT+ and BAT–
• The system load and charger connect across BAT+ and PACK–
• To the I2C and HDQ serial communication ports
• To the ALERT output
2.2
Pin Descriptions
PIN NAME
BAT +
BAT –
PACK –
SDA
SCL
GND
HDQ
ALERT
3
DESCRIPTION
Positive battery stack and pack connection
Negative battery stack connection
Pack negative terminal
I2C data signal
I2C clock signal
Communication and ALERT grounds
HDQ serial communication signal
ALERT output signal
bq34z110 Circuit Module
This section contains information on the schematic for the bq34z110 implementation.
3.1
Choosing SingleCell (1S) or MultiCell operation
The bq34z110 operates in one of two modes for measuring battery voltage. Place two jumpers on header
J5 to select the mode of operation. Refer to the silk screen markings near J5 on the EVM.
WARNING
Applying a voltage higher than 5 V when jumpers are configured
for ≤ 5-V operation is very likely to damage the IC.
The ≤ 5-V mode simplifies the circuit from that shown in the schematic. Most of the components shown to
the left of the bq34z110 are not necessary.
3.2
Choosing Maximum MultiCell Battery Voltage
In the MultiCell > 5-V setup, three levels of maximum battery voltage: 16, 32, and 48 V are selectable on
the header J2. Refer to the schematic and silkscreen markings on the EVM for jumper placement. Ideally,
the total divider ratio, including the 16.5-kΩ resistor, R28, converts the maximum expected voltage on the
battery to something between 0.8 V and 1.0 V at the BAT pin of the gauge. For this reason, test points
TP1 and TP2 are provided to customize the top leg of the divider for your application. While the bq34z110
firmware is able to handle battery voltage up to 65 V, voltages above 50 V should never be applied to the
EVM.
SLUUA15 – October 2012
Submit Documentation Feedback
bq34z110EVM Wide-Range Impedance Track™ Enabled Fuel Gauge
Solution for Lead-Acid Batteries
Copyright © 2012, Texas Instruments Incorporated
3
Circuit Module Physical Layouts, Schematic, and Bill of Materials
3.3
www.ti.com
Choosing the LED configuration
When configuring the data flash registers, choose one of five LED/Comm configuration codes (refer to
Table 12 in the bq34z110 datasheet). After reviewing those possibilities, select the jumper pattern desired
for the J6 header on the EVM. For single-LED mode, place a jumper on the pair marked A. For four-direct
LED mode, place jumpers on A, B, C, and D. For external LEDs using the shift register option, place a
single jumper on EXT. In all cases, where one or more LED’s are used, place a jumper across the J1
header to provide power to the LED.
3.4
Choosing the ALERT configuration
The pin used to provide the ALERT output depends on the LED mode selected in the LED/Comm data
flash register. Refer to Table 13 in the bq34z110 datasheet for a guide to the proper ALERT pin, then
place one and only one jumper on the J3 header accordingly.
4
Circuit Module Physical Layouts, Schematic, and Bill of Materials
This section contains the board layout, assembly drawings, schematic, and bill of materials for the
bq34z110 circuit module.
4.1
Board Layout
Figure 1 through Figure 6 show the PCB layers, and assembly drawing for the bq34z110 module.
TP4
TP5
J7
TP3
TP8
TP7
TP6
U1
U3
J6
J1
J4
J3
J5
RT1
J2
U2
TB3
SW1
TB1
Figure 1. bq34z110EVM Layout (Silkscreen)
4
bq34z110EVM Wide-Range Impedance Track™ Enabled Fuel Gauge
Solution for Lead-Acid Batteries
Copyright © 2012, Texas Instruments Incorporated
SLUUA15 – October 2012
Submit Documentation Feedback
Circuit Module Physical Layouts, Schematic, and Bill of Materials
www.ti.com
D17
D15
D16
D14
D9
R9
R10
R11
R8
1
R36
R35
U3
U1
TP5
J7
Q6
J6
R16
C1
R7
1
TP4
D1
D4
R17
TP3
R12
R18
R20
R22
R23
R24
R19
D5
TP8
TP7
TP6
C4
1
D10
D11
D12
D13
C3
D6
R34
R37
D3
1
J3
J1
Q2
R33
R32
Q1
1
R29
R31
R15
D8
J4
R13
R14
J5
1
R21
D2
R28
C8
J2
TP2
C2
C9
U2
C5
C6
C7
R30
TB3
R5
R6
Q7
RT1
R2
R4
R1
R26
R27
1
R3
R25
R38
TP1
Q5
Q4
Q3
Q8
D7
SW1
R40
R39
TB1
Figure 2. bq34z110EVM Top Assembly
Figure 3. bq34z110EVM Top Layer
SLUUA15 – October 2012
Submit Documentation Feedback
bq34z110EVM Wide-Range Impedance Track™ Enabled Fuel Gauge
Solution for Lead-Acid Batteries
Copyright © 2012, Texas Instruments Incorporated
5
Circuit Module Physical Layouts, Schematic, and Bill of Materials
www.ti.com
Figure 4. bq34z110EVM Inner Layer 1
Figure 5. bq34z110EVM Inner Layer 2
6
bq34z110EVM Wide-Range Impedance Track™ Enabled Fuel Gauge
Solution for Lead-Acid Batteries
Copyright © 2012, Texas Instruments Incorporated
SLUUA15 – October 2012
Submit Documentation Feedback
www.ti.com
Circuit Module Physical Layouts, Schematic, and Bill of Materials
Figure 6. bq34z110EVM Bottom Layer
SLUUA15 – October 2012
Submit Documentation Feedback
bq34z110EVM Wide-Range Impedance Track™ Enabled Fuel Gauge
Solution for Lead-Acid Batteries
Copyright © 2012, Texas Instruments Incorporated
7
Circuit Module Physical Layouts, Schematic, and Bill of Materials
4.2
www.ti.com
Schematic
R2
100K
R4
165K
1
Q4
BSS138
1
GND
REGIN
R35
100
R36
R37
100
R34
100
4
100
J2
1
2
3
4
5
6
Q5
BSS84
1
R1
R26
300K .1%
R27
300K .1%
16V
3
P3
32V
2
P1
GND
R41 27K
Q3
2N7002
R39
47
4
Q8
2N7002
C2
J5
5V
8
SH2
BAT +
16.5K .1%
3
Q6
2SK3019
REG25
7
R28
2
J3
D5
Q2
2SK3019
LED CONFIGURATION OPTIONS
GND
LED5
D13 QTLP610C-3 YEL
R12
1.5K
LED4
D14 QTLP610C-3 YEL
R18
1.5K
LED3
D15 QTLP610C-4 GRN
R20
1.5K
LED2
D16 QTLP610C-4 GRN
R22
1.5K
J6
Fiducial Marks
GND
GND
P4
P3
P2
P1
U1
SN74HC164PW
1
A
REGIN
VCC
14
C4
0.1uF
2
B
QH
13
TP8
LED1
D17 QTLP610C-4 GRN
R23
1.5K
3
QA
QG
12
TP7
LED0
D6
R24
1.5K
4
QB
QF
11
TP6
10
TP5
QTLP610C-4 GRN
TP3
5
QC
QE
TP4
6
QD
~CLR
9
7
GND
CLK
8
GND
R32
1M
R33
1M
GND
GND
1
2
3
4
5
6
7
8
9
10
D
C
B
A
EXT
P2
GND
1
2
3
4
Optional for additional power saving
Adjust for minimum current consumption in the application
I2C pullups normally implemented in the host. Duplicated here since EV2300 does not provide
Optimize for required LED power dissipation
Figure 7. bq34z110EVM Schematic
8
bq34z110EVM Wide-Range Impedance Track™ Enabled Fuel Gauge Solution
for Lead-Acid Batteries
Copyright © 2012, Texas Instruments Incorporated
SLUUA15 – October 2012
Submit Documentation Feedback
Circuit Module Physical Layouts, Schematic, and Bill of Materials
www.ti.com
4.2.1
Bill of Materials
Table 2 is the BOM for the bq34z110EVM.
Table 2. bq34z110EVM Bill of Materials
Count
RefDes
Value
Description
Size
Part Number
MFR
2
C1, C8
1uF
Capacitor, Ceramic, 6.3V, X7R, 20%
0603
Std
Any
6
C2–C7
0.1uF
Capacitor, Ceramic, 50V, X7R, 20%
0603
Std
Any
1
1
C9
3300 pF
Capacitor, Ceramic, 50V, X7R, 20%
0603
Std
Any
2
2
D1, D2
AZ23C5V6-7
Diode, Dual, Zener, 5.6 V, 300mW
SOT23
AZ23C5V6-7
Diodes
3
3
D12, D13, D14
QTLP610C-3 YEL
Diode, LED yellow, 30-mA
0.126 x 0.087 inch
QTLP610C-3
Fairchild
8
8
D3–D6, D8, D15–D17
QTLP610C-4 GRN
Diode, LED green, 30-mA
0.126 x 0.087 inch
QTLP610C-4
Fairchild
1
1
D7
BZT52C5V6S-7
Diode, Zener, 200mW, 5.6V
SOD-323
BZT52C5V6S-7
Diodes Inc
3
3
D9, D10, D11
QTLP610C-7 RED
Diode, LED red, 30-mA
0.126 x 0.087 inch
QTLP610C-7
Fairchild
1
1
J1
PEC02SAAN
Header, Male 2-pin, 100mil spacing,
0.100 inch x 2
PEC02SAAN
Sullins
1
1
J2
PEC03DAAN
Header, Male 2x3-pin, 100mil spacing
0.20 inch x 0.30
PEC03DAAN
Sullins
1
1
J3
PEC04DAAN
Header, Male 2x4-pin, 100mil spacing
0.20 x 0.40 inch
PEC04DAAN
Sullins
2
2
J4, J7
22-05-3041
Header, Friction Lock Ass'y, 4-pin Right Angle
0.400 x 0.500
22-05-3041
Molex
1
1
J5
PEC08SAAN
Header, Male 8-pin, 100mil spacing,
0.100 inch x 8
PEC08SAAN
Sullins
1
1
J6
PEC05DAAN
Header, Male 2x5-pin, 100mil spacing
0.100 inch x 5 X 2
PEC05DAAN
Sullins
4
4
Q1, Q2, Q6, Q7
2SK3019
MOSFET, Nch, 30V, 100mA, 8 Ohm
SC-75A
2SK3019
Rohm
2
2
Q3 Q8
2N7002
MOSFET, N-ch, 60-V, 115-mA, 1.2-Ohms
SOT23
2N7000-7-F
Diodes Inc
1
1
Q4
BSS138
MOSFET, Nch, 50V, 0.22A, 3.5 Ohm
SOT23
BSS138
Fairchild
1
1
Q5
BSS84
MOSFET, P-ch, 50-V, 130-mA, 10-Ohms
SOT23
BSS84
Fairchild
3
3
R1, R26, R27
300K 0.1%
Resistor, Chip, 0.1W, 0.1%, 25 ppm
0603
RG1608P-304-B-T5
SSM
1
1
R2
100K
Resistor, Chip, 1/16-W, 1%
0402
Std
Std
2
2
R3, R41
27K
Resistor, Chip, 1/16-W, 5%
0402
Std
Std
1
1
R4
165K
Resistor, Chip, 1/16-W, 1%
0402
Std
Std
8
8
R5, R6, R13, R14, R34–R37
100
Resistor, Chip, 1/16W, 5%
0603
Std
Any
1
1
R7
2M
Resistor, Chip, 1/16-W, 5%
0402
Std
Std
14
14
R8–R12, R15–R20,
R22–R24
1.5K
Resistor, Chip, 1/16-W, 5%
0402
Std
Std
1
1
R21
220K
Resistor, Chip, 1/16-W, 5%
0402
Std
Std
1
1
R25
200
Resistor, Chip, 1/16W, 5%
0603
Std
Any
1
1
R28
16.5K .1%
Resistor, Chip, 0.1W, 0.1%, 25 ppm
0603
RG1608P-1652-B-T5
SSM
2
2
R29, R31
10K
Resistor, Chip, 1/16-W, 5%
0402
Std
Std
1
1
R30
.010 75ppm
Resistor, Chip, 1/2W, 1%, 75ppm
2010
WSL2010R0100FEA
Dale
2
2
R32, R33
1M
Resistor, Chip, 1/16-W, 5%
0402
Std
Std
1
1
R38
1k
Resistor, Chip, 1/16-W, 5%
402
Std
Std
2
2
R39-40
47
Resistor, Chip, 1/16-W, 5%
402
Std
Std
1
1
RT1
10K
Thermistor, NTC, 3-A
0.095 X 0.150 inch
103AT-2
Semitec
1
1
SW1
EVQ-PLHA15
Switch, Push button, Momentary, N.O. Low Profile
0.200 x 0.200 inch
EVQ-PLHA15
Panasonic
-001
-002
2
6
SLUUA15 – October 2012
Submit Documentation Feedback
bq34z110EVM Wide-Range Impedance Track™ Enabled Fuel Gauge Solution
for Lead-Acid Batteries
Copyright © 2012, Texas Instruments Incorporated
9
Circuit Module Physical Layouts, Schematic, and Bill of Materials
www.ti.com
Table 2. bq34z110EVM Bill of Materials (continued)
Count
RefDes
Value
Description
Size
Part Number
MFR
2
TB1, TB3
ED555/3DS
Terminal Block, 3-pin, 6A, 3.5mm
0.41 x 0.25 inch
ED555/3DS
OST
1
TP1
Vscale Hi
Test Point, Black, Thru Hole Color Keyed
0.100 x 0.100 inch
5001
Keystone
1
1
TP2
Vscale Lo
Test Point, Black, Thru Hole Color Keyed
0.100 x 0.100 inch
5001
Keystone
0
0
TP3–TP8
STD
Test Point, 0.020 Hole
Std
Std
2
2
U1, U3
SN74HC164PW
IC, 8-Bit Parallel-Out Serial Shift Registers
TSSOP-14
SN74HC164PW
TI
1
0
U2
BQ34Z100PW
IC, Gas Gauge
TSSOP
BQ34Z100PW
0
1
U2
BQ34Z110PW
IC, Gas Gauge
TSSOP
BQ34Z110PW
1
1
—
2
2
J4 mate
Connector, Female, 0.100 Centers
Molex
22-01-3047
8
8
N/A
Terminals, Crimp, Tin
Molex
05-50-0114
N/A
Wire, Insulated 24 Awg, Red, 18 inches (+/-3 inches) (USB_5V)
Alpha
1854-3
N/A
Wire, Insulated 24 Awg, White, 18 inches (+/-3 inches) (SCL)
Alpha
1854-1
N/A
Wire, Insulated 24 Awg, Black, 18 inches (+/-3 inches) (GND)
Alpha
1854-2
N/A
Wire, Insulated 24 Awg, Brown, 18 inches (+/-3 inches) (SDA)
Alpha
1854-7
N/A
Heatshrink 1"
Any
Any
-001
-002
2
1
PCB, 68 mm x 50 mm x 1 mm
PWR111
Any
CONNECTOR
1
1
last row
Notes: 1. These assemblies are ESD sensitive, observe ESD precautions.
2. These assemblies must be clean and free from flux and all contaminants. Use of no-clean flux is not acceptable.
3. These assemblies must comply with workmanship standards IPC-A-610 Class 2.
4. Reference designators marked with an asterisk ('**') cannot be substituted. All other components can be substituted with equivalent MFG's components.
5. Make one SMBus connector wire assembly for each assembly produced, from J4 mate, 4–24 Awg wires and crimp terminals. Wire colors for pin numbers are listed below. Place a J4 mate on each end of the wire assembly.
6. Install label after final wash. Make text 8 pt font and exactly as shown in the Assembly Number Label table below
Assembly Number Label
10
Assembly Number
Text
PWR111-001
BQ34Z100EVM
PWR111-002
BQ34Z100EVM
bq34z110EVM Wide-Range Impedance Track™ Enabled Fuel Gauge Solution
for Lead-Acid Batteries
Copyright © 2012, Texas Instruments Incorporated
SLUUA15 – October 2012
Submit Documentation Feedback
EVM Hardware and Software Setup
www.ti.com
4.3
bq34z110 Circuit Module Performance Specification Summary
This section summarizes the performance specifications of the bq34z110 circuit module.
Table 3. Performance Specification Summary
Specification
Min
Input voltage BAT+ to BAT- in ≤ 5-V mode
5
Typ
Max
Units
2.7
4
5
V
Input voltage BAT+ to BAT- in MultiCell > 5-V mode
5
28
50
V
Charge and discharge current
0
2
7
A
EVM Hardware and Software Setup
This section describes how to install the bq34z110EVM PC software and how to connect the different
components of the EVM.
5.1
System Requirements
The bq34z110EVSW requires Windows 2000, Windows XP, Windows Vista, or Windows 7.
5.2
Software Installation
NOTE: For the latest software archive, contact the Texas Instruments field representative assigned
to this device.
Install the bq34z110EVSW software with the following steps:
1. Save the archive to a temporary directory.
2. Double-click the executable filename and follow the installer instructions to complete the bq34z110
EVSW installation.
If the EV2300 or EV2400 was not previously installed: After bq34z110 EVSW installation, a TI USB
DRIVER INSTALLER pops up. Click Yes for the agreement message and follow its instructions.
3. Plug the EV2300 or EV2400 into a USB port.
5.3
Troubleshooting Unexpected Dialog Boxes
Users downloading the files must be logged in as the administrator, or must have privileges to install new
programs.
The driver is not signed, so the administrator must allow installation of unsigned drivers.
5.4
Hardware Connection
The bq34z110EVM comprises two hardware components: the bq34z110 circuit module and either the
EV2300 or EV2400 PC-interface box.
SLUUA15 – October 2012
Submit Documentation Feedback
bq34z110EVM Wide-Range Impedance Track™ Enabled Fuel Gauge
Solution for Lead-Acid Batteries
Copyright © 2012, Texas Instruments Incorporated
11
EVM Hardware and Software Setup
5.4.1
www.ti.com
Connecting the bq34z110 Circuit Module to a Battery Pack
Figure 8 shows how to connect the bq34z110 circuit module to the cells and system load and charger.
Figure 8. bq34z110 Circuit Module Connection to Cells and System Load and Charger
5.4.2
PC Interface Connection
Configure the hardware to interface with the PC by doing the following:
1. Connect the bq34z110 device-based smart battery to the EV2300 or EV2400 using the provided cable
or the connections shown in Table 4.
Table 4. Circuit Module to EV2300 or EV2400 Connections
bq34z110 Device-Based Battery
EV2300
SDA
I2C SDA
SCL
I2C SCL
GND
GND
2. Connect the PC USB cable to the EV2300 or EV2400 and the PC USB port.
The bq34z110EVM-001 is now set up for operation.
12
bq34z110EVM Wide-Range Impedance Track™ Enabled Fuel Gauge
Solution for Lead-Acid Batteries
Copyright © 2012, Texas Instruments Incorporated
SLUUA15 – October 2012
Submit Documentation Feedback
EVM Hardware and Software Setup
www.ti.com
5.5
Operation
This section details the operation of the bq34z110 EVSW software.
NOTE: Neither the EV2300 or EV2400 driver supports Windows Sleep or Hibernate states. If
communicating with the EV2300 or EV2400 or the EVM presents a problem, unplug the USB
cable and then plug it back in.
5.5.1
Starting the Program
With the EV2300 or EV2400 and the bq34z110EVM connected to the computer, run bq34z110 EVSW
from the Desktop Icon or Start | All Programs | Texas Instruments | bq Evaluation Software menu
sequence. The Data RAM Screen appears. Data begins to appear once the Refresh (single time scan)
button is clicked, or when the Keep Scanning check box is checked. To disable the scan feature,
deselect Keep Scanning.
The continuous scanning period can be set using the Options and Set Scan Interval menu selections. The
range for this interval is 0 ms to 65535 ms. Only items that are selected for scanning are scanned within
this period.
The bq34z110 EVSW provides a logging function that logs the values that were last scanned by the
EVSW. To enable this function, click the Start Logging button; this causes the Keep Scanning button to
be selected. When logging is Stopped, the Keep Scanning button is still selected and must be manually
unchecked.
The logging interval is specified under the Options menu with the maximum value of 65535 ms. The Log
interval cannot be smaller than the scan interval because this results in the same value being logged at
least twice.
SLUUA15 – October 2012
Submit Documentation Feedback
bq34z110EVM Wide-Range Impedance Track™ Enabled Fuel Gauge
Solution for Lead-Acid Batteries
Copyright © 2012, Texas Instruments Incorporated
13
EVM Hardware and Software Setup
www.ti.com
Figure 9. Data RAM Screen
Figure 9 shows the Data RAM set along with additional ManuFacturersAccess() command information,
such as individual cell measurements.
Dragging the splitter bar, the line that separates the Flags/Static data from Data RAM values, changes the
height of the Flags/Static Data display. Selecting View then Auto Arrange returns the splitter bar to its
original location.
5.5.2
Setting Programmable bq34z110 Options
The bq34z110 data flash comes configured according to the default settings detailed in the bq34z110
Wide Range Fuel Gauge with Impedance Track™ Technology Datasheet (SLUSB55). Ensure that the
settings are correctly changed to match the pack and application for the bq34z110 solution being
evaluated.
NOTE: Set these options correctly to get the best performance.
14
bq34z110EVM Wide-Range Impedance Track™ Enabled Fuel Gauge
Solution for Lead-Acid Batteries
Copyright © 2012, Texas Instruments Incorporated
SLUUA15 – October 2012
Submit Documentation Feedback
EVM Hardware and Software Setup
www.ti.com
Use Figure 10, the Data Flash Screen to configure the settings.
Figure 10. Data Flash Screen, Gas Gauging Class
Click on menu option | Data Flash | Read All | to read all the data from the bq34z110 data flash.
Write to a data flash location by clicking on the desired location and entering the data. Clicking Enter
writes the entire tab of flash data. Writing to a data flash location can also be accomplished by selecting
menu option | Data Flash | Write All |. The data flash must be read before any writes are performed to
avoid having incorrect data written to the device.
The | File | Special Export | menu option allows the data flash to be exported.
Save the data flash configuration to a file by selecting | File | Export | and entering a file name. A data
flash file also can be retrieved in this way, imported, and written to the bq34z110 using the Write All
button.
The configuration information of the bq34z110 data is held in the data flash.
The bq34z110 allows for an automatic data flash export function, similar to the Data RAM logging
function. This feature, when selected using | Options | Auto Export |, exports data flash to a sequential
series of files named FilenameNNNNN.gg; where N = a decimal number from 0 to 9.
The AutoExport interval is set under the | Options menu | with a minimum value of 15 s. The AutoExport
filename is set under the | Options menu |.
When a check is next to | AutoExport |, the AutoExport is in progress. The same menu selection is used
to turn AutoExport on and off.
If the data-flash screen is blank, the bq34z110 used may not be supported by the bqEVSW version in use.
An upgrade may be required.
SLUUA15 – October 2012
Submit Documentation Feedback
bq34z110EVM Wide-Range Impedance Track™ Enabled Fuel Gauge
Solution for Lead-Acid Batteries
Copyright © 2012, Texas Instruments Incorporated
15
EVM Hardware and Software Setup
5.6
5.6.1
www.ti.com
Calibration Screen
How to Calibrate
Calibrate the bq34z110 using appropriate floating power supplies before the cells are attached. Complete
the following before the bq34z110 is calibrated:
• Connect and measure a 1- to 2-A stable current source from BAT(–) to PACK(–). The positive lead
from the current source is connected to PACK(-) simulating a discharge current.
• Connect and measure a stable voltage source from BAT(+) to BAT(–).
• Measure the temperature near the thermistor.
Whether all of the preceding steps are required depends on the type of calibration being performed.
5.6.2
Calibrating the bq34z110
Calibrate the bq34z110 using the following sequential steps:
1. Select the types of calibration to be performed.
2. Enter the measured values for the types of calibration selected (except for offset calibrations).
3. If Temperature Calibration is selected, select the sensor that is to be calibrated.
4. Click the appropriate button to initiate calibration.
Figure 11. Calibration Screen
16
bq34z110EVM Wide-Range Impedance Track™ Enabled Fuel Gauge
Solution for Lead-Acid Batteries
Copyright © 2012, Texas Instruments Incorporated
SLUUA15 – October 2012
Submit Documentation Feedback
EVM Hardware and Software Setup
www.ti.com
5.7
5.7.1
2
I C Pro (Advanced) Screen
I2C Communication
The set of read and write operations over I2C bus are not specific to any gas gauge. These are provided
as general-purpose communication tools.
5.7.2
Reprogramming
Reprogram the device using the following:
• Ensure that the gauge is in Full Access mode. The SS and FAS flags in the Control Status register
must both be unasserted (Green). If not, use the appropriate data block codes to command (0x00) to
clear the flags. Type default codes of 0414,3672 into the Write I2C Data Block feature to unseal and
ffff, ffff for full access, or into the value field of the control register on the Data Ram screen followed by
pressing Enter. Stop the scan during this operation to ensure the words are received consecutively.
• With scanning enabled, using the Write I2C Data Block feature commands the gauge to stop executing
and enter ROM mode. Send data block code 0x000f to command 0x00. If successful, the status at the
bottom of the screen changes from Communication OK to Communication Error.
• Use the file browser button to locate the desired .senc file, press the Program button.
• When programming is complete, pushing the Execute button initiates program execution. Within a few
seconds Communication OK appears in the status area.
• Close and re-open the Evaluation Software to ensure data file synchronization.
Figure 12. I2C Pro (Advanced) Screen
SLUUA15 – October 2012
Submit Documentation Feedback
bq34z110EVM Wide-Range Impedance Track™ Enabled Fuel Gauge
Solution for Lead-Acid Batteries
Copyright © 2012, Texas Instruments Incorporated
17
EVM Hardware and Software Setup
5.8
www.ti.com
Send HDQ Screen
When using the HDQ single wire serial communication feature, the mode of the gauge must be changed
with a special command. This screen provides a button for this purpose. Note the warning message. The
process is not reversible. Once in HDQ mode, the HDQ pro screen is available for testing commands and
reprogramming the device. For register scanning and data flash access, use the companion evaluation
program for HDQ.
Figure 13. Send HDQ Screen
18
bq34z110EVM Wide-Range Impedance Track™ Enabled Fuel Gauge
Solution for Lead-Acid Batteries
Copyright © 2012, Texas Instruments Incorporated
SLUUA15 – October 2012
Submit Documentation Feedback
EVM Hardware and Software Setup
www.ti.com
5.9
bqChem
bqChem provides access to the library of previously characterized Lithium-Ion cell chemistries. bqChem
also lets you program the chemical database into the gauge. Users can sort by chemical ID or by cell
manufacturer. For help identifying the chemistry for the cells, contact the Texas Instruments field
representative.
Figure 14. bqChem Screen
5.10 Related Documentation from Texas Instruments
For related documentation, contact the TI field representative.
Documents:
bq34z110/bq30z55-R1 SBS 1.1-Compliant Gas Gauge With Impedance Track™
Datasheet
EV2300 EVM Interface Board User's Guide
EV2400 EVM Interface Board User's Guide
SLUUA15 – October 2012
Submit Documentation Feedback
Literature Number:
SLUSB55
SLUU159
SLUU446
bq34z110EVM Wide-Range Impedance Track™ Enabled Fuel Gauge
Solution for Lead-Acid Batteries
Copyright © 2012, Texas Instruments Incorporated
19
EVALUATION BOARD/KIT/MODULE (EVM) ADDITIONAL TERMS
Texas Instruments (TI) provides the enclosed Evaluation Board/Kit/Module (EVM) under the following conditions:
The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user indemnifies TI from all claims
arising from the handling or use of the goods.
Should this evaluation board/kit not meet the specifications indicated in the User’s Guide, the board/kit may be returned within 30 days from
the date of delivery for a full refund. THE FOREGOING LIMITED WARRANTY IS THE EXCLUSIVE WARRANTY MADE BY SELLER TO
BUYER AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING ANY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. EXCEPT TO THE EXTENT OF THE INDEMNITY SET FORTH
ABOVE, NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL
DAMAGES.
Please read the User's Guide and, specifically, the Warnings and Restrictions notice in the User's Guide prior to handling the product. This
notice contains important safety information about temperatures and voltages. For additional information on TI's environmental and/or safety
programs, please visit www.ti.com/esh or contact TI.
No license is granted under any patent right or other intellectual property right of TI covering or relating to any machine, process, or
combination in which such TI products or services might be or are used. TI currently deals with a variety of customers for products, and
therefore our arrangement with the user is not exclusive. TI assumes no liability for applications assistance, customer product design,
software performance, or infringement of patents or services described herein.
REGULATORY COMPLIANCE INFORMATION
As noted in the EVM User’s Guide and/or EVM itself, this EVM and/or accompanying hardware may or may not be subject to the Federal
Communications Commission (FCC) and Industry Canada (IC) rules.
For EVMs not subject to the above rules, this evaluation board/kit/module is intended for use for ENGINEERING DEVELOPMENT,
DEMONSTRATION OR EVALUATION PURPOSES ONLY and is not considered by TI to be a finished end product fit for general consumer
use. It generates, uses, and can radiate radio frequency energy and has not been tested for compliance with the limits of computing
devices pursuant to part 15 of FCC or ICES-003 rules, which are designed to provide reasonable protection against radio frequency
interference. Operation of the equipment may cause interference with radio communications, in which case the user at his own expense will
be required to take whatever measures may be required to correct this interference.
General Statement for EVMs including a radio
User Power/Frequency Use Obligations: This radio is intended for development/professional use only in legally allocated frequency and
power limits. Any use of radio frequencies and/or power availability of this EVM and its development application(s) must comply with local
laws governing radio spectrum allocation and power limits for this evaluation module. It is the user’s sole responsibility to only operate this
radio in legally acceptable frequency space and within legally mandated power limitations. Any exceptions to this are strictly prohibited and
unauthorized by Texas Instruments unless user has obtained appropriate experimental/development licenses from local regulatory
authorities, which is responsibility of user including its acceptable authorization.
For EVMs annotated as FCC – FEDERAL COMMUNICATIONS COMMISSION Part 15 Compliant
Caution
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the
equipment.
FCC Interference Statement for Class A EVM devices
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the interference at his own expense.
FCC Interference Statement for Class B EVM devices
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
For EVMs annotated as IC – INDUSTRY CANADA Compliant
This Class A or B digital apparatus complies with Canadian ICES-003.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the
equipment.
Concerning EVMs including radio transmitters
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired
operation of the device.
Concerning EVMs including detachable antennas
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain
approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should
be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
This radio transmitter has been approved by Industry Canada to operate with the antenna types listed in the user guide with the maximum
permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain
greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
Cet appareil numérique de la classe A ou B est conforme à la norme NMB-003 du Canada.
Les changements ou les modifications pas expressément approuvés par la partie responsable de la conformité ont pu vider l’autorité de
l'utilisateur pour actionner l'équipement.
Concernant les EVMs avec appareils radio
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est
autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout
brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Concernant les EVMs avec antennes détachables
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain
maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à
l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente
(p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante.
Le présent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés dans le manuel
d’usage et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus dans
cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur.
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
【Important Notice for Users of this Product in Japan】
】
This development kit is NOT certified as Confirming to Technical Regulations of Radio Law of Japan
If you use this product in Japan, you are required by Radio Law of Japan to follow the instructions below with respect to this product:
1.
2.
3.
Use this product in a shielded room or any other test facility as defined in the notification #173 issued by Ministry of Internal Affairs and
Communications on March 28, 2006, based on Sub-section 1.1 of Article 6 of the Ministry’s Rule for Enforcement of Radio Law of
Japan,
Use this product only after you obtained the license of Test Radio Station as provided in Radio Law of Japan with respect to this
product, or
Use of this product only after you obtained the Technical Regulations Conformity Certification as provided in Radio Law of Japan with
respect to this product. Also, please do not transfer this product, unless you give the same notice above to the transferee. Please note
that if you could not follow the instructions above, you will be subject to penalties of Radio Law of Japan.
Texas Instruments Japan Limited
(address) 24-1, Nishi-Shinjuku 6 chome, Shinjuku-ku, Tokyo, Japan
http://www.tij.co.jp
【ご使用にあたっての注】
本開発キットは技術基準適合証明を受けておりません。
本製品のご使用に際しては、電波法遵守のため、以下のいずれかの措置を取っていただく必要がありますのでご注意ください。
1.
2.
3.
電波法施行規則第6条第1項第1号に基づく平成18年3月28日総務省告示第173号で定められた電波暗室等の試験設備でご使用いただく。
実験局の免許を取得後ご使用いただく。
技術基準適合証明を取得後ご使用いただく。
なお、本製品は、上記の「ご使用にあたっての注意」を譲渡先、移転先に通知しない限り、譲渡、移転できないものとします。
上記を遵守頂けない場合は、電波法の罰則が適用される可能性があることをご留意ください。
日本テキサス・インスツルメンツ株式会社
東京都新宿区西新宿６丁目２４番１号
西新宿三井ビル
http://www.tij.co.jp
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
EVALUATION BOARD/KIT/MODULE (EVM)
WARNINGS, RESTRICTIONS AND DISCLAIMERS
For Feasibility Evaluation Only, in Laboratory/Development Environments. Unless otherwise indicated, this EVM is not a finished
electrical equipment and not intended for consumer use. It is intended solely for use for preliminary feasibility evaluation in
laboratory/development environments by technically qualified electronics experts who are familiar with the dangers and application risks
associated with handling electrical mechanical components, systems and subsystems. It should not be used as all or part of a finished end
product.
Your Sole Responsibility and Risk. You acknowledge, represent and agree that:
1.
2.
3.
4.
You have unique knowledge concerning Federal, State and local regulatory requirements (including but not limited to Food and Drug
Administration regulations, if applicable) which relate to your products and which relate to your use (and/or that of your employees,
affiliates, contractors or designees) of the EVM for evaluation, testing and other purposes.
You have full and exclusive responsibility to assure the safety and compliance of your products with all such laws and other applicable
regulatory requirements, and also to assure the safety of any activities to be conducted by you and/or your employees, affiliates,
contractors or designees, using the EVM. Further, you are responsible to assure that any interfaces (electronic and/or mechanical)
between the EVM and any human body are designed with suitable isolation and means to safely limit accessible leakage currents to
minimize the risk of electrical shock hazard.
You will employ reasonable safeguards to ensure that your use of the EVM will not result in any property damage, injury or death, even
if the EVM should fail to perform as described or expected.
You will take care of proper disposal and recycling of the EVM’s electronic components and packing materials.
Certain Instructions. It is important to operate this EVM within TI’s recommended specifications and environmental considerations per the
user guidelines. Exceeding the specified EVM ratings (including but not limited to input and output voltage, current, power, and
environmental ranges) may cause property damage, personal injury or death. If there are questions concerning these ratings please contact
a TI field representative prior to connecting interface electronics including input power and intended loads. Any loads applied outside of the
specified output range may result in unintended and/or inaccurate operation and/or possible permanent damage to the EVM and/or
interface electronics. Please consult the EVM User's Guide prior to connecting any load to the EVM output. If there is uncertainty as to the
load specification, please contact a TI field representative. During normal operation, some circuit components may have case temperatures
greater than 60°C as long as the input and output are maintained at a normal ambient operating temperature. These components include
but are not limited to linear regulators, switching transistors, pass transistors, and current sense resistors which can be identified using the
EVM schematic located in the EVM User's Guide. When placing measurement probes near these devices during normal operation, please
be aware that these devices may be very warm to the touch. As with all electronic evaluation tools, only qualified personnel knowledgeable
in electronic measurement and diagnostics normally found in development environments should use these EVMs.
Agreement to Defend, Indemnify and Hold Harmless. You agree to defend, indemnify and hold TI, its licensors and their representatives
harmless from and against any and all claims, damages, losses, expenses, costs and liabilities (collectively, "Claims") arising out of or in
connection with any use of the EVM that is not in accordance with the terms of the agreement. This obligation shall apply whether Claims
arise under law of tort or contract or any other legal theory, and even if the EVM fails to perform as described or expected.
Safety-Critical or Life-Critical Applications. If you intend to evaluate the components for possible use in safety critical applications (such
as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, such as devices
which are classified as FDA Class III or similar classification, then you must specifically notify TI of such intent and enter into a separate
Assurance and Indemnity Agreement.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which
have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such
components to meet such requirements.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated
工商网监
湘ICP备2023018690号
