Product
Folder
Sample &
Buy
Support &
Community
Tools &
Software
Technical
Documents
LM3686
SNVS520F – AUGUST 2008 – REVISED NOVEMBER 2016
LM3686 Step-Down DC-DC Converter With Integrated Post Linear Regulators System And
Low-Noise Linear Regulator
1 Features
2 Applications
•
•
•
•
•
1
•
•
•
DC-DC Regulator
– VOUT_DCDC = 1.2 V to 2.5 V
– 600-mA Maximum ILOAD
– 3-MHz Typical PWM Fixed Switching
Frequency
– Automatic PFM/PWM Mode Switching
– Internal Synchronous Rectification
– Internal Soft Start
Dual-Rail Linear Regulator: LILO
– Load Transients < 50-mV Peak Typical
– Line Transients < 1-mV Peak Typical
– VOUT_LILO = 0.7 V to 2 V
– 70-µA Typical IQ and 300-mA Maximum ILOAD
Linear Regulator: LDO
– Load Transients < 80-mV Peak Typical
– Line Transients < 1-mV Peak Typical
– VOUT_LDO = 1.5 V to 3.3 V
– 50-µA Typical IQ and 350-mA Maximum ILOAD
Combined Global Features
– VBATT ≥ Maximum (VOUT_LILO + 1.5 V, 2.7 V)
– Operates From a Single Li-Ion Cell or 3-Cell
NiMH/NiCd Batteries
– 100-µA IQ and 900-mA Maximum ILOAD
Mobile TVs, Hand-Held Radios
Personal Digital Assistants, Palm-Top PCs
Portable Instruments and Personal Clients
Battery-Powered Devices
3 Description
The LM3686 is a step-down DC-DC converter with a
very low-dropout linear regulator and a low-noise
linear regulator optimized for powering ultra-low
voltage circuits. It provides three outputs with
combined load current up to 900 mA over an input
voltage range from 2.7 V to 5.5 V.
The device offers superior features and performance
for many applications. Automatic intelligent switching
between PWM low-noise and PFM low-current mode
offers improved system control. During full-power
operation, a fixed-frequency 3 MHz (typical), PWM
mode drives loads from approximately 70 mA to 600
mA maximum. Hysteretic PFM mode extends the
battery life through reduction of the quiescent current
to 28 μA (typical) at light load and system standby.
Internal synchronous rectification provides high
efficiency.
Device Information(1)
PART NUMBER
PACKAGE
LM3686
DSBGA (12)
BODY SIZE (NOM)
2.435 mm × 1.687 mm
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
Typical Application
VBATT
2.7 V to 5.5 V
4.7 PF, 0603
EN_DCDC
LM3686
3 MHz
DC-DC
PGND
1 PH
SW
1.8 V
FB_DCDC
VIN_LILO
10 PF
0603
PGND
EN_LILO
Dual Rail
LILO
350 mA
EN_LDO
VIN_LDO
LILO
2.2 PF,
0402
Linear Regulator
300 mA
LDO
1 PF,
0402
1 PF, 0402
PGND
0.7 V to 2 V
350 mA
QGND
1.2 V to 3.3 V
300 mA
QGND
QGND
QGND
Copyright © 2016, Texas Instruments Incorporated
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
LM3686
SNVS520F – AUGUST 2008 – REVISED NOVEMBER 2016
www.ti.com
Table of Contents
1
2
3
4
5
6
7
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Description (Continued) ........................................
Pin Configuration and Functions .........................
Specifications.........................................................
1
1
1
2
3
3
4
7.1
7.2
7.3
7.4
7.5
7.6
7.7
7.8
Absolute Maximum Ratings ...................................... 4
ESD Ratings.............................................................. 4
Recommended Operating Conditions....................... 4
Thermal Information .................................................. 4
Electrical Characteristics: Linear Regulator - LILO ... 5
Electrical Characteristics: Linear Regulator - LDO ... 6
Electrical Characteristics: DC-DC Converter ............ 7
Electrical Characteristics: Global Parameters (DCDC,
LILO, and LDO).......................................................... 8
7.9 Typical Characteristics .............................................. 9
8
Detailed Description ............................................ 11
8.1 Overview ................................................................. 11
8.2 Functional Block Diagram ....................................... 12
8.3 Feature Description................................................. 12
8.4 Device Functional Modes........................................ 16
9
Application and Implementation ........................ 17
9.1 Application Information............................................ 17
9.2 Typical Application ................................................. 17
10 Power Supply Recommendations ..................... 22
11 Layout................................................................... 22
11.1 Layout Guidelines ................................................ 22
11.2 Layout Example .................................................... 23
11.3 DSBGA Package Assembly and Use ................... 23
12 Device and Documentation Support ................. 24
12.1
12.2
12.3
12.4
12.5
12.6
12.7
Device Support......................................................
Related Documentation .......................................
Receiving Notification of Documentation Updates
Community Resources..........................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
24
24
24
24
24
24
24
13 Mechanical, Packaging, and Orderable
Information ........................................................... 24
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision E (May 2013) to Revision F
Page
•
Deleted "one integrated" ........................................................................................................................................................ 1
•
Deleted "from a single Li-Ion cell or 3-cell NiMH/NiCd batteries." ......................................................................................... 1
•
Added Device Information and ESD Ratings tables, Pin Configuration and Functions, Feature Description, Device
Functional Modes, Application and Implementation, Power Supply Recommendations, Layout, Device and
Documentation Support, and Mechanical, Packaging, and Orderable Information sections ................................................. 1
•
Combine some bullet items and delete parentheticals from Features to get more space .................................................... 1
•
Deleted out-of-date Device Comparison table ...................................................................................................................... 3
•
Deleted lead temperature from Abs Max per TI data sheet standard ................................................................................... 4
•
Changed RθJA from "120°C/W" to "80.9°C/W"; added additional thermal values ................................................................... 4
•
Changed "drains conductor" to "drains inductor" on Figure 13 ............................................................................................ 14
Changes from Revision D (April 2013) to Revision E
•
2
Page
Changed layout of National Semiconductor data sheet to TI format.................................................................................... 22
Submit Documentation Feedback
Copyright © 2008–2016, Texas Instruments Incorporated
Product Folder Links: LM3686
LM3686
www.ti.com
SNVS520F – AUGUST 2008 – REVISED NOVEMBER 2016
5 Description (Continued)
Three enable (EN_x) pins allow the separate operation of either the DC-DC, post-regulation linear regulator, or
the linear regulator alone. If the DC-DC is not enabled during start-up of the post-regulation linear regulator, a
parallel small-pass transistor supplies the linear regulator from VBATT with maximal 50 mA. In the combined
operation where both enables are raised together, the small-pass transistor is deactivated and the big pass
transistor provides 350 mA output current. In shutdown mode (EN_x pins pulled low), the device turns off and
reduces battery consumption to 2.5 μA (typical).
The LM3686 is available in a 12-pin DSBGA package. A high-switching frequency of 3 MHz (typical) allows the
use of a few tiny surface-mount components. Only six external surface-mount components, an inductor and five
ceramic capacitors, are required to establish a 15.66 mm2 total solution size.
6 Pin Configuration and Functions
YZR Package
12-Pin DSBGA
Top View
YZR Package
12-Pin DSBGA
Bottom View
A3
B3
C3
D3
D3
C3
B3
A3
A2
B2
C2
D2
D2
C2
B2
A2
A1
B1
C1
D1
D1
C1
B1
A1
Pin Functions
PIN
TYPE
DESCRIPTION
NO.
NAME
A1
PGND
Ground
Power ground pin
A2
SW
Analog
Switching node connection to the internal PFET switch and NFET synchronous rectifier.
A3
FB_DCDC
Input
B1
VBATT
Power
B2
EN_LILO
Input
Enable input for the linear regulator. The linear regulator is in shutdown mode if voltage at
this pin is
< 0.4 V and enabled if > 1.1 V. Do not leave this pin floating.
B3
EN_DCDC
Input
Enable input for the DC-DC converter. The DC-DC converter is in shutdown mode if voltage
at this pin is < 0.4 V and enabled if > 1.1 V. Do not leave this pin floating.
C1
VIN_LDO
Input
Input power to LDO — must tie to VBATT at all times.
C2
EN_LDO
Input
Enable input for the linear regulator. The linear regulator is in shutdown mode if voltage at
this pin is
< 0.4 V and enabled if > 1.1 V. Do not leave this pin floating.
C3
QGND
Ground
Quiet GND pin for LDO and reference circuit
D1
VOUT_LDO
Output
Voltage output of the linear regulator
D2
VOUT_LILO
Output
Voltage output of the low input linear regulator
D3
VIN_LILO
Input
Feedback analog input for the DC-DC converter. Connect to the output filter capacitor.
Power supply input for switcher. Connect to the input filter capacitor.
Input power to LILO (VIN_LILO) connects to output of DCDC or standalone.
Submit Documentation Feedback
Copyright © 2008–2016, Texas Instruments Incorporated
Product Folder Links: LM3686
3
LM3686
SNVS520F – AUGUST 2008 – REVISED NOVEMBER 2016
www.ti.com
7 Specifications
7.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted) (1) (2) (3) (4)
VBATT pin to GND and QGND
MIN
MAX
UNIT
–0.2
6
V
(GND – 0.2 V) to (VBATT+0.2 V) with 6 V
maximum
EN_x pins, FB_DC-DC pin, SW pin
Continuous power dissipation (5)
Internally limited
Junction temperature, TJ-MAX
Storage temperature, Tstg
(1)
(2)
(3)
(4)
(5)
–65
150
°C
150
°C
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
All voltages are with respect to the potential at the GND pin.
If Military/Aerospace specified devices are required, contact the Texas Instruments Sales Office/Distributors for availability and
specifications.
For detailed soldering specifications and information, see AN-1112 DSBGA Wafer Level Chip Scale Package.
Internal thermal shutdown circuitry protects the device from permanent damage. Thermal shutdown engages at TJ = 150°C (typical) and
disengages at TJ = 130°C (typical).
7.2 ESD Ratings
VALUE
V(ESD)
(1)
(2)
Electrostatic discharge
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001 (1)
±2000
Charged-device model (CDM), per JEDEC specification JESD22-C101 (2)
±200
UNIT
V
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
7.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
MIN
MAX
Input voltage, VBATT (DC-DC and LDO)
2.7
5.5
V
Junction temperature, TJ
–40
125
°C
Ambient temperature, TA (1)
–40
85
°C
(1)
UNIT
In applications where high power dissipation and/or poor package thermal resistance is present, the maximum ambient temperature may
have to be derated. Maximum ambient temperature (TA-MAX) is dependent on the maximum operating junction temperature (TJ-MAX-OP =
125°C), the maximum power dissipation of the device in the application (PD-MAX), and the junction-to ambient thermal resistance of the
part/package in the application (RθJA), as given by the following equation: TA-MAX = TJ-MAX-OP – (RθJA × PD-MAX).
7.4 Thermal Information
LM3686
THERMAL METRIC (1)
YZR (DSBGA)
UNIT
12 PINS
RθJA
Junction-to-ambient thermal resistance
80.9
°C/W
RθJC(top)
Junction-to-case (top) thermal resistance
0.4
°C/W
RθJB
Junction-to-board thermal resistance
16.8
°C/W
ψJT
Junction-to-top characterization parameter
0.2
°C/W
ψJB
Junction-to-board characterization parameter
16.9
°C/W
(1)
4
For more information about traditional and new thermal metrics, see Semiconductor and IC Package Thermal Metrics.
Submit Documentation Feedback
Copyright © 2008–2016, Texas Instruments Incorporated
Product Folder Links: LM3686
LM3686
www.ti.com
SNVS520F – AUGUST 2008 – REVISED NOVEMBER 2016
7.5 Electrical Characteristics: Linear Regulator - LILO
Unless otherwise noted, limits apply for TA = 25°C, specifications apply to the closed-loop typical application circuits (linear
regulator) with VIN_LDO = VBATT = 3.6 V (1) , VIN_LILO = VOUT_DCDC(NOM), VEN (All) = VBATT, CIN_DC = 4.7 μF, COUT_LILO = 2.2 μF,
CIN_LDO = 1 μF , COUT_LDO = 1 μF, COUT_DC = CIN_LILO = 10 μF. (2) (3) (4) (5)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
EN_DC-DC = EN_LILO = ON – LARGE NMOS
ΔVOUT_LILO,
VOUT_LILO
ΔVOUT_LILO /
ΔmA
VDROP
Output voltage accuracy,
VOUT-LILO
Load regulation
(6)
Dropout voltage
IOUT_LILO = 1 mA to 350 mA,
VIN_LILO = VOUT_DCDC
VBATT = 3.6 V
IOUT_LILO = 1 mA to 350 mA,
VIN_LILO = VOUT_DCDC
VBATT = 3.6 V, –40°C ≤ TA = TJ ≤ 85°C
1.2
V
1.176
IOUT_LILO = 1 mA to 350 mA,
VIN_LILO = VOUT_DCDC
VBATT = 3.6 V
1.224
4
μV/mA
IOUT_LILO = 1 mA to 350 mA,
VIN_LILO = VOUT_DCDC
VBATT = 3.6 V, –40°C ≤ TA = TJ ≤ 85°C
(7)
12
VBATT = VOUT_LILO + 1.5 V (VIN_LILO
disconnected from VOUT_DCDC)
IOUT = 350 mA
50
mV
VBATT = VOUT_LILO + 1.5 V (VIN_LILO
disconnected from VOUT_DCDC)
IOUT = 350 mA, –40°C ≤ TA = TJ ≤ 85°C
80
VBATT = VIN_LILO = 3.6 V
IQ_VIN_LILO
Quiescent current
ISC_LILO
Short-circuit current limit
70
VBATT = VIN_LILO = 3.6 V
–40°C ≤ TA = TJ ≤ 85°C
VOUT = GND (VOUT_LILO = 0)
–40°C ≤ TA = TJ ≤ 85°C
µA
90
400
mA
EN_DC-DC = OFF, EN_LILO = ON – SMALL NMOS
ΔVOUT_LILO,
VOUT_LILO
Output voltage accuracy
VOUT_LILO
ΔVOUT_LILO,
ΔVBATT
VIN_LILO = (VOUT_LILO + 0.3 V) to 5.5 V
Line regulation (small NMOS) (8) VIN_LILO = (VOUT_LILO + 0.3 V) to 5.5 V
–40°C ≤ TA = TJ ≤ 85°C
ISC_LILO
Short-circuit current
VOUT_LILO = GND, –40°C ≤ TA = TJ ≤
85°C
TSTARTUP
Start-up time
EN to 0.95 VOUT
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
IOUT = 1 mA to 50 mA
–40°C ≤ TA = TJ ≤ 85°C
1.176
1.224
V
0.4
1.5
mV/V
70
70
µs
VIN_LDO must be ON at all time for biasing internal reference circuits.
All voltages are with respect to the potential at the GND pin.
Minimum (MIN) and maximum (MAX) limits are specified by design, test, or statistical analysis. Typical (TYP) numbers represent the
most likely norm. Unless otherwise specified, conditions for typical specifications are: VBATT = 3.6 V and TA = 25°C.
The parameters in the electrical characteristic table are tested at VBATT = 3.6 V unless otherwise specified. For performance over the
input voltage range refer to Typical Characteristics.
The input voltage ranges recommended for ideal application performance for the specified output voltages are:
VBATT = 2.7 V to 5.5 V for 1 V ≤ VOUT_DCDC < 1.8 V
VBATT = (VOUT_DCDC + 1 V) to 5.5 V for 1.8 V ≤ VOUT_DCDC < 3.6 V.
To calculate the output voltage from the load regulation specified, use the following equation:
ΔVOUT = load regulation (%/mA) × nominal VOUT (V) × ΔIOUT (mA).
Dropout voltage is defined as the input to output voltage differential at which the output voltage falls to 100 mV below the nominal output
voltage.
To calculate the output voltage from the line regulation specified, use the following equation:
ΔVOUT = line regulation (%/V) × nominal VOUT (V) × ΔVIN (V).
Submit Documentation Feedback
Copyright © 2008–2016, Texas Instruments Incorporated
Product Folder Links: LM3686
5
LM3686
SNVS520F – AUGUST 2008 – REVISED NOVEMBER 2016
www.ti.com
Electrical Characteristics: Linear Regulator - LILO (continued)
Unless otherwise noted, limits apply for TA = 25°C, specifications apply to the closed-loop typical application circuits (linear
regulator) with VIN_LDO = VBATT = 3.6 V(1) , VIN_LILO = VOUT_DCDC(NOM), VEN (All) = VBATT, CIN_DC = 4.7 μF, COUT_LILO = 2.2 μF,
CIN_LDO = 1 μF , COUT_LDO = 1 μF, COUT_DC = CIN_LILO = 10 μF.(2)(3)(4)(5)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
SYSTEM CHARACTERISTICS (9)
PSRR
Power supply rejection ratio
Signal to VBATT = 3.6 V, VIN_LILO = 1.8 V,
IOUT = 200 mA, ƒ = 100 Hz
68
Signal to VIN_LILO = 1.8 V,
IOUT = 200 mA, ƒ = 100 kHz
60
dB
eN_LILO
Output noise voltage
BW = 10 Hz to 100 kHz, VIN_LILO = 1.8 V,
IOUT = 200 mA, VIN_LDO = 3.6 V
ΔVOUT_LILO
Dynamic load transient
response
Pulsed load 1 mA to 350 mA
di/dt = 350 mA / 1 µs
±30 (10)
mV
ΔVIN_LILO
Dynamic load transient
response on VBATT
VBATT = 3.1 V to 3.7 V
VIN_LILO = VOUT_DCDC
tr, tf = 10 µs, IOUT = 200 mA
±15 (10)
mV
166
µVRMS
(9) Specified by design. Not production tested.
(10) For line and load transient specifications, the + symbol represents an overshoot in the output voltage and the – symbol represents an
undershoot in the output voltage. The first value signifies overshoot or undershoot at the rising edge and the second value signifies the
overshoot or undershoot at the falling edge.
7.6 Electrical Characteristics: Linear Regulator - LDO
Unless otherwise noted, limits apply for TA = 25°C. (1) (2) (3) (4)
PARAMETER
VIN_LDO
TEST CONDITIONS
LDO input voltage range
MIN
VIN = 3.6 V, IOUT_LDO = 1 mA and 300 mA
ΔVOUT_LDO Output voltage accuracy, VOUT/ VOUT_LDO LDO
VIN = 3.6 V, IOUT_LDO = 1 mA and 300 mA
–40°C ≤ TA = TJ ≤ 85°C
ΔVOUT_LDO
Load regulation (5)
/ ΔmA
IOUT_LDO = 1 mA and 300 mA
ΔVOUT_LDO
Line regulation (6)
/ ΔVBATT
2.744
3
V
mV/V
IOUT = 300 mA
120
Ven = 0.95 V, IOUT = 0 mA
–40°C ≤ TA = TJ ≤ 85°C
ISC_LDO
Short-circuit current limit
VOUT = GND, –40°C ≤ TA = TJ ≤ 85°C
6
3.06
2.94
IOUT = 300 mA, –40°C ≤ TA = TJ ≤ 85°C
200
Ven = 0.95 V, IOUT = 0 mA
(7)
2.856
0.2
Quiescent current
(6)
V
VIN_LDO = (VOUT_LDO(NOM) + 0.3 V) to 5.5 V
IQ
(5)
UNIT
μV/mA
Dropout voltage (7)
(4)
5.5
8
VDROP
(3)
MAX
2.8
VIN = 3.6 V, IOUT_LDO = 1 mA and 300 mA
VIN = 3.6 V, IOUT_LDO = 1 mA and 300 mA
–40°C ≤ TA = TJ ≤ 85°C
(1)
(2)
TYP
2.7
mV
50
80
350
µA
mA
All voltages are with respect to the potential at the GND pin.
Minimum (MIN) and maximum (MAX) limits are specified by design, test, or statistical analysis. Typical (TYP) numbers represent the
most likely norm. Unless otherwise specified, conditions for typical specifications are: VBATT = 3.6 V and TA = 25°C.
The parameters in the Electrical Characteristics tables are tested at VBATT = 3.6 V unless otherwise specified. For performance over the
input voltage range refer to Typical Characteristics.
The input voltage ranges recommended for ideal application performance for the specified output voltages are
VBATT = 2.7 V to 5.5 V for 1 V ≤ VOUT_DCDC < 1.8 V
VBATT = (VOUT_DCDC + 1 V) to 5.5 V for 1.8 V ≤ VOUT_DCDC < 3.6 V
To calculate the output voltage from the load regulation specified, use the following equation:
ΔVOUT = load regulation (%/mA) × nominal VOUT (V) × ΔIOUT (mA)
To calculate the output voltage from the line regulation specified, use the following equation:
ΔVOUT = line regulation (%/V) × nominal VOUT (V) × ΔVIN (V)
Dropout voltage is defined as the input to output voltage differential at which the output voltage falls to 100 mV below the nominal output
voltage.
Submit Documentation Feedback
Copyright © 2008–2016, Texas Instruments Incorporated
Product Folder Links: LM3686
LM3686
www.ti.com
SNVS520F – AUGUST 2008 – REVISED NOVEMBER 2016
Electrical Characteristics: Linear Regulator - LDO (continued)
Unless otherwise noted, limits apply for TA = 25°C.(1)(2)(3)(4)
PARAMETER
SYSTEM CHARACTERISTICS
PSRR
TEST CONDITIONS
TYP
Power supply rejection ratio
EN_DC = EN_LILO = GND
IOUT = 200 mA, ƒ = 1 kHz
85
Signal to VIN_LDO = 3.6 V,
IOUT = 200 mA, ƒ = 10 kHz
70
6.7
eN_LDO
Output noise voltage
BW = 10 Hz to 100 kHz, VIN_LDO = 3.6 V,
IOUT = 200 mA
ΔVIN_LDO
Dynamic line transient response
VIN_LDO = 3.8 V to 4.4 V
tr, tf = 30 µs, IOUT = 1 mA
ΔVIN_LILO
Dynamic load transient
response on VBATT
Pulsed load 1 mA and 300 mA
tr, tf = 10 µs
(8)
(9)
MIN
MAX
UNIT
(8)
dB
µVRMS
±2 (9)
mV
±30 (9)
mV
Specified by design. Not production tested.
For line and load transient specifications, the + symbol represents an overshoot in the output voltage and the – symbol represents an
undershoot in the output voltage. The first value signifies overshoot or undershoot at the rising edge and the second value signifies the
overshoot or undershoot at the falling edge.
7.7 Electrical Characteristics: DC-DC Converter
Unless otherwise noted, limits apply for TA = 25°C. (1) (2) (3) (4)
PARAMETER
TEST CONDITIONS
MIN
PWM mode (5)
TYP
MAX
UNIT
VFB_DCDC
Feedback voltage
accuracy
VREF
Internal reference
voltage
RDSON(P)
Pin-pin resistance for
PFET
VBATT = 3.6 V
ISW = 100 mA
350
450
mΩ
RDSON(N)
Pin-pin resistance for
NFET
VBATT = 3.6 V
ISW = 100 mA
150
250
mΩ
Quiescent current for
auto mode
No load, device is not switching, FB = HIGH
IQ_AUTO
ILIM
Switch peak current
limit
Open loop
ƒOSC
Internal oscillator
frequency
PWM mode
(1)
(2)
(3)
(4)
(5)
1.8
PWM mode (5), –40°C ≤ TA = TJ ≤ 85°C
1.746
V
1.836
0.5
V
28
No load, device is not switching, FB = HIGH
–40°C ≤ TA = TJ ≤ 85°C
µA
40
1.22
Open loop, –40°C ≤ TA = TJ ≤ 85°C
1.035
3
PWM mode, –40°C ≤ TA = TJ ≤ 85°C
2.4
A
1.375
3.4
MHz
All voltages are with respect to the potential at the GND pin.
Minimum (MIN) and maximum (MAX) limits are specified by design, test, or statistical analysis. Typical (TYP) numbers represent the
most likely norm. Unless otherwise specified, conditions for typical specifications are: VBATT = 3.6 V and TA = 25°C.
The parameters in the electrical characteristic table are tested at VBATT = 3.6 V unless otherwise specified. For performance over the
input voltage range refer to Typical Characteristics.
The input voltage ranges recommended for ideal application performance for the specified output voltages are:
VBATT = 2.7 V to 5.5 V for 1 V ≤ VOUT_DCDC < 1.8 V
VBATT = (VOUT_DCDC + 1 V) to 5.5 V for 1.8 V ≤ VOUT_DCDC < 3.6 V
Electrical Characteristics tables reflects open loop data (FB = 0 V and current drawn from SW pin ramped up until cycle by cycle current
limit is activated). Closed loop current limit is the peak inductor current measured in the application circuit by increasing output current
until output voltage drops by 10%.
Submit Documentation Feedback
Copyright © 2008–2016, Texas Instruments Incorporated
Product Folder Links: LM3686
7
LM3686
SNVS520F – AUGUST 2008 – REVISED NOVEMBER 2016
www.ti.com
7.8 Electrical Characteristics: Global Parameters (DCDC, LILO, and LDO)
Unless otherwise noted, limits apply for TA = 25°C. (1) (2) (3) (4)
PARAMETER
IQ_VBATT
IQ_GLOBAL
Quiescent current into
VBATT
Shutdown current into
VBATT
TEST CONDITIONS
MIN
Full power mode
IOUT_DCDC = IOUT_LILO = IOUT_LDO = 0 mA, DC-DC
is not switching (FB_DCDC forced higher than
VOUT_DCDC)
Ven = 1.1V,
TYP
MAX
UNIT
100
µA
Full power mode
IOUT_DCDC = IOUT_LILO = IOUT_LDO = 0 mA, DC-DC
is not switching (FB_DCDC forced higher than
VOUT_DCDC)
Ven = 1.1V,
–40°C ≤ TA = TJ ≤ 85°C
130
VEN_DCDC = VEN_LILO = VEN_LDO = 0 V
2.5
VEN_DCDC = VEN_LILO = VEN_LDO = 0
–40°C ≤ TA = TJ ≤ 85°C
4
µA
ENABLE PINS (EN_DCDC, EN_LILO, EN_LDO)
IEN
Enable pin input
current
All EN = 0 V
VIH
Logic high input
–40°C ≤ TA = TJ ≤ 85°C
VIL
Logic low input
–40°C ≤ TA = TJ ≤ 85°C
(1)
(2)
(3)
(4)
8
.01
All EN = 0 V, –40°C ≤ TA = TJ ≤ 85°C
µA
1
1.1
V
0.4
V
All voltages are with respect to the potential at the GND pin.
Mininum (MIN) and maximum (MAX) limits are specified by design, test, or statistical analysis. Typical (TYP) numbers represent the
most likely norm. Unless otherwise specified, conditions for typical specifications are: VBATT = 3.6 V and TA = 25°C.
The parameters in the Electrical Characteristics tables are tested at VBATT = 3.6 V unless otherwise specified. For performance over the
input voltage range refer to Typical Characteristics.
The input voltage ranges recommended for ideal application performance for the specified output voltages are:
VBATT = 2.7 V to 5.5 V for 1 V ≤ VOUT_DCDC < 1.8 V
VBATT = (VOUT_DCDC + 1 V) to 5.5 V for 1.8 V ≤ VOUT_DCDC < 3.6 V
Submit Documentation Feedback
Copyright © 2008–2016, Texas Instruments Incorporated
Product Folder Links: LM3686
LM3686
www.ti.com
SNVS520F – AUGUST 2008 – REVISED NOVEMBER 2016
7.9 Typical Characteristics
Unless otherwise specified, typical application (post regulation), VBATT = 3.6 V, TA = 25°C, enable pins tied to VBATT, VOUT_DCDC
= 1.8 V, VOUT_LILO = 1.2 V, VOUT_LDO = 2.8 V.
1.830
1. 203
VIN = 3.6V
1. 202
OUTPUT VOLTAGE (V)
OUTPUT VOLTAGE (V)
1.825
VIN = 2.9V
1.820
1.815
1.810
.
VIN = 4.5 V
1. 201
1. 200
VIN = 2.9V
1. 199
VIN = 4.5V
1. 198
1. 197
1. 196
VIN = 3.6V
1. 195
1.805
.
1. 194
1. 193
1.800
.
0
100
200
300
400
500
600
0
50
100
150
200
250
300
OUTPUT CURRENT ( mA)
OUTPUT CURRENT DC-DC (mA)
Figure 1. VOUT_DCDC vs IOUT_DCDC
Figure 2. VOUT_LILO vs IOUT_LILO
0
-10
PSRR (dB)
-20
-30
-40
-50
-60
ILILO = 200 mA
-70
-80
100
1k
10k
100k
1000k 10000k
FREQUENCY (Hz)
LILO – VIN_LILO = 3.6 V
Figure 3. Efficiency DC-DC vs Output Current LILO and LDO
Disabled
Figure 4. PSRR vs Frequency
0
-20
PSRR (dB)
-40
-60
ILDO = 200 mA
-80
-100
-120
100
1k
10k
100k
1000k 10000k
FREQUENCY (Hz)
LDO – VIN_LDO = 3.6 V
LDO – VIN_LDO = 3.6 V
Figure 6. Noise vs Frequency
Figure 5. PSRR vs Frequency
Submit Documentation Feedback
Copyright © 2008–2016, Texas Instruments Incorporated
Product Folder Links: LM3686
9
LM3686
SNVS520F – AUGUST 2008 – REVISED NOVEMBER 2016
www.ti.com
Typical Characteristics (continued)
Unless otherwise specified, typical application (post regulation), VBATT = 3.6 V, TA = 25°C, enable pins tied to VBATT, VOUT_DCDC
= 1.8 V, VOUT_LILO = 1.2 V, VOUT_LDO = 2.8 V.
Open Loop
Figure 7. Switching Frequency vs Temperature
Figure 8. Current Limit vs Temperature
All Three Enables Tied
Together
Figure 9. RDSON vs Temperature
10
Figure 10. Start-up
Submit Documentation Feedback
Copyright © 2008–2016, Texas Instruments Incorporated
Product Folder Links: LM3686
LM3686
www.ti.com
SNVS520F – AUGUST 2008 – REVISED NOVEMBER 2016
8 Detailed Description
8.1 Overview
The LM3686 incorporates a high efficiency synchronous switching step-down DC-DC converter, a very low
dropout linear regulator (LILO), and ultra-low-noise linear regulator.
The DC-DC converter delivers a constant voltage from a single Li- Ion battery and input voltage rails from 2.7 V
to 5.5 V to portable devices such as cell phones and PDAs. Using a voltage mode architecture with synchronous
rectification, it has the ability to deliver up to 600-mA load current (when not powering the LILO) depending on
the input voltage, output voltage, ambient temperature, and the inductor chosen.
The linear regulator delivers a constant voltage biased from VIN_LILO power input typically the output voltage of
the DC-DC converter is used (post regulation) with a maximum load current of 350 mA.
The other linear regulator delivers a constant voltage biased from VIN_LDO power input with a maximum load
current of 300 mA.
Three enable pins allow the independent control of the three outputs. Shutdown mode turns off the device,
offering the lowest current consumption (ISHUTDOWN = 2.5 µA typical).
Besides the shutdown feature, there are two more modes of operation for the DC-DC converter, depending on
the current required:
• Pulse width modulation (PWM) and
• Pulse frequency modulation (PFM).
The device operates in PWM mode at load current of approximately 80 mA or higher. Lighter load current cause
the device to automatically switch into PFM for reduced current consumption (IQ_VBATT = 28 µA typical) and a
longer battery life.
Additional features include soft-start, start-up mode of the linear regulator, undervoltage protection, current
overload protection, and overtemperature protection.
An internal reference generates a 1.8-V biasing an internal resistive divider to create a reference voltage range
from 0.7 V to 1.8 V (in 50-mV steps) for the LILO and the 0.5-V reference used for the DC-DC converter. The
ultra-low-noise linear regulator also has internal reference that generates a 1.8-V biasing for a internal resistor
divider, thus creating a reference voltage ranging from 1.5 V to 3.3 V.
The undervoltage lockout feature enables the device to start-up once VBATT has reached 2.65 V typically and
turns the device off if VBATT drops below 2.41 V typically.
NOTE
Post regulation: When the DC-DC converter is switched off while the linear regulator is still
enabled, the LILO can still support up to 50 mA. The linear regulator LILO is turned on via
a small NMOS device supplied by VIN_LDO . The maximum current is 50 mA when this
small NMOS is ON. If higher current > 50 mA is desired the following condition must be
met:
• EN_DC = HIGH
When the condition is met, the LILO transitions to the large NMOS and can support up to
350 mA.
Submit Documentation Feedback
Copyright © 2008–2016, Texas Instruments Incorporated
Product Folder Links: LM3686
11
LM3686
SNVS520F – AUGUST 2008 – REVISED NOVEMBER 2016
www.ti.com
8.2 Functional Block Diagram
VIN_LDO/VIN_VBATT
VBATT
VIN_LILO
Driver
LDO
Digital
VREF
LILO
SW
Analog
buck
(error amplifier)
Buck system
VOUT_LDO
VOUT_LILO
PGND
(Power ground)
QGND
(Analog ground)
Copyright © 2016, Texas Instruments Incorporated
Always connect VIN_LDO to VBATT.
8.3 Feature Description
8.3.1 DC-DC Converter Operation
During the first part of each switching cycle, the control block in the LM3686 turns on the internal PFET switch.
This allows current to flow from the input VBATT through the switch pin SW and the inductor to the output filter
capacitor and load. The inductor limits the current to a ramp with a slope of (VBATT – VOUT_DCDC) / L, by storing
energy in the magnetic field.
During the second part of each cycle, the controller turns the PFET switch off, blocking current flow from the
input, and then turns the NFET synchronous rectifier on. The inductor draws current from ground through the
NFET to the output filter capacitor and load, which ramps the inductor current down with a slope of (– VOUT_DCDC
/ L).
The output filter stores charge when the inductor current is high, and releases it when low, smoothing the voltage
across the load.
The output voltage is regulated by modulating the PFET switch on time to control the average current sent to the
load. The effect is identical to sending a duty-cycle modulated rectangular wave formed by the switch and
synchronous rectifier at the SW pin to a low-pass filter formed by the inductor and output filter capacitor. The
output voltage is equal to the average voltage at the SW pin.
12
Submit Documentation Feedback
Copyright © 2008–2016, Texas Instruments Incorporated
Product Folder Links: LM3686
LM3686
www.ti.com
SNVS520F – AUGUST 2008 – REVISED NOVEMBER 2016
Feature Description (continued)
8.3.1.1 PWM Operation
During pulse width modulation (PWM) operation the converter operates as a voltage-mode controller with input
voltage feed forward. This allows the converter to achieve good load and line regulation. The DC gain of the
power stage is proportional to the input voltage. To eliminate this dependency, feed forward inversely
proportional to the input voltage is introduced.
While in PWM mode, the output voltage is regulated by switching at a constant frequency and then modulating
the energy per cycle to control power to the load. At the beginning of each clock cycle the PFET switch is turned
on and the inductor current ramps up until the duty-cycle comparator trips and the control logic turns off the
switch. The current limit comparator can also turn off the switch in case the current limit of the PFET is
exceeded. Then the NFET switch is turned on and the inductor current ramps down. The next cycle is initiated by
the clock turning off the NFET and turning on the PFET.
2V/DIV
VSW
VBATT = 3.6V
VOUT = 1.8V
IOUT = 500 mA
IL
200 mA/DIV
VOUT
2 mV/DIV
AC Coupled
TIME (330 ns/DIV)
Figure 11. Typical PWM Operation
8.3.1.2 PFM Operation
At very light load, the DC-DC converter enters PFM mode and operates with reduced switching frequency and
supply current to maintain high efficiency. The part automatically transitions into PFM mode when either of two
conditions occurs for a duration of 32 or more clock cycles:
1. The NFET current reaches zero.
2. The peak PMOS switch current drops below the IMODE level, (typically IMODE < 75 mA + VBATT / 55 Ω ).
VBATT = 3.6V
VSW
IL
VOUT = 1.8V
IOUT = 20 mA
VOUT
TIME (1 µs/DIV)
Figure 12. Typical PFM Operation
Submit Documentation Feedback
Copyright © 2008–2016, Texas Instruments Incorporated
Product Folder Links: LM3686
13
LM3686
SNVS520F – AUGUST 2008 – REVISED NOVEMBER 2016
www.ti.com
Feature Description (continued)
During PFM operation, the DC-DC converter positions the output voltage slightly higher than the nominal output
voltage during PWM operation, allowing additional headroom for voltage drop during a load transient from light to
heavy load. The PFM comparators sense the output voltage via the feedback pin and control the switching of the
output FETs such that the output voltage ramps between approximately 0.2% and approximately 1.8% above the
nominal PWM output voltage. If the output voltage is below the high PFM comparator threshold, the PMOS
power switch is turned on. It remains on until the output voltage reaches the high PFM threshold or the peak
current exceeds the IPFM level set for PFM mode. The typical peak current in PFM mode is: IPFM = 112 mA +
VBATT / 20 Ω.
Once the PMOS power switch is turned off, the NMOS power switch is turned on until the inductor current ramps
to zero. When the NMOS zero-current condition is detected, the NMOS power switch is turned off. If the output
voltage is below the high PFM comparator threshold (see Figure 13), the PMOS switch is again turned on and
the cycle is repeated until the output reaches the desired level. Once the output reaches the high PFM threshold,
the NMOS switch is turned on briefly to ramp the inductor current to zero. Both output switches are then turned
off, and the device enters an extremely low power mode. Quiescent supply current during this sleep mode is 28
µA (typical), which allows the part to achieve high efficiency under extremely light load conditions.
If the load current should increase during PFM mode (see Figure 13) causing the output voltage to fall below the
low2 PFM threshold, the part automatically transitions into fixed-frequency PWM mode.
When VBATT = 2.7 V the device transitions from PWM to PFM mode at approximately 35 mA output current and
from PFM mode to PWM mode at approximately 95 mA. When VBATT= 3.6 V, PWM-to-PFM transition happens at
approximately 42 mA and PFM-to-PWM transition happens at approximately 115 mA. When VBATT = 4.5 V,
PWM-to-PFM transition happens at approximately 60 mA and PFM-to-PWM transition happens at approximately
135 mA.
High PFM Threshold
~1.017*Vout
PFM Mode at Light Load
Load current
increases
Low1 PFM Threshold
~1.006*Vout
ZA
xi
s
High PFM
Voltage
Threshold
reached,
go into
sleep mode
Low PFM
Threshold,
turn on
PFET
Low2 PFM Threshold,
switch back to PWMmode
Zs
Axi
Pfet on
until
Ipfm limit
reached
Nfet on
drains
inductor
current
until
I inductor = 0
Current load
increases,
draws Vout
towards
Low2 PFM
Threshold
Low2 PFM Threshold
Vout
PWM Mode at
Moderate to Heavy
Loads
Figure 13. Operation In PFM Mode and Transfer to PWM Mode
8.3.1.3 Internal Synchronous Rectification
While in PWM mode, the DC-DC converter uses an internal NFET as a synchronous rectifier to reduce rectifier
forward voltage drop and associated power loss. Synchronous rectification provides a significant improvement in
efficiency whenever the output voltage is relatively low compared to the voltage drop across an ordinary rectifier
diode.
14
Submit Documentation Feedback
Copyright © 2008–2016, Texas Instruments Incorporated
Product Folder Links: LM3686
LM3686
www.ti.com
SNVS520F – AUGUST 2008 – REVISED NOVEMBER 2016
Feature Description (continued)
8.3.1.4 Current Limiting
A current limit feature allows the LM3686 to protect itself and external components during overload conditions.
PWM mode implements current limiting using an internal comparator that trips at 1220 mA (typical). If the output
is shorted to ground the device enters a timed current limit mode where the NFET is turned on for a longer
duration until the inductor current falls below a low threshold. This allows the inductor current more time to
decay, thereby preventing runaway.
8.3.1.5 Soft Start
The DC-DC converter has a soft-start circuit that limits in-rush current during start-up. During start-up the switchcurrent limit is increased in steps. Soft start is activated only if EN_DCDC goes from logic low to logic high after
VBATT reaches 2.7 V. Soft start is implemented by increasing switch current limit in steps of 200 mA, 400 mA, 600
mA and 1220 mA (typical switch current limit). The start-up time thereby depends on the output capacitor and
load current demanded at start-up. Typical start-up times with a 10 µF output capacitor and 200 mA load is 350
µs and with 1 mA load is 200 µs.
8.3.2 Linear Regulator Operation (LILO)
In a typical post-regulation application the power input voltage VIN_LILO for the linear regulator is generated by the
DC-DC converter. Using a buck converter to reduce the battery voltage to a lower input voltage for the linear
regulator translates to higher efficiency and lower power dissipation.
It is also possible to operate the linear regulator independent of the DC-DC converter output voltage either from
VIN_LDO/VBATT or from a different source (VIN_LILO) – (IOUT_LILO = 50 mA maximum in independent mode).
An input capacitor of 1 µF at VIN_LILO is needed to be added if no other filter or bypass capacitor is present in the
VIN_LILO path.
8.3.2.1 Start-up Mode
If VIN_LILO > VOUT_LILO(NOM) + 250 mV the main regulator is active, offering a rated output current of 350 mA and
supplied by VIN_LILO (large NMOS).
If VIN_LILO < VOUT_LILO(NOM) + 150 mV the start-up LILO is active, providing a reduced rated output current of 50
mA typical, supplied by VBATT (small NMOS).
Figure 14. Start-Up Sequence, VEN_DCDC = VEN_LILO = V
EN_LDO
= VBATT
8.3.3 Current Limiting (LDO and LILO)
The LM3686 incorporates also a current limit for the LDO and LILO to protect itself and external components
during overload conditions at their outputs. In the event of a peak overcurrent condition at VOUT_LDO or VOUT_LILO ,
the output current through the NFET pass device is limited.
Submit Documentation Feedback
Copyright © 2008–2016, Texas Instruments Incorporated
Product Folder Links: LM3686
15
LM3686
SNVS520F – AUGUST 2008 – REVISED NOVEMBER 2016
www.ti.com
8.4 Device Functional Modes
Table 1. Enable Combinations
EN_DCDC
EN_LILO
EN_LDO
0
0
0
No outputs
0
0
1
Linear regulator enabled only (EN_LDO), supply from VIN_LDO, IOUT_MAX = 300 mA
0
1
0
Linear regulator enabled only LILO supplies from VIN_LDO,
IOUT_MAX = 50 mA, VIN_LDO > = VOUT_LILO
1
0
0
DC-DC converter enabled only
1
1
0
Linear regulator and DC-DC enabled
1. VIN_LILO < VOUT_LILO + 150 mV (typical), the small NMOS device is active (IMAX = 50
mA) and supplied by VIN_LDO.
2. If VIN_LILO > VOUT_LILO + 250 mV (typical), the large NMOS device is active (IMAX =
350 mA) and supplied by VIN_LILO. Maxium current of DC-DC when EN_LILO = High
is 250 mA (1) (2)
1
1
1
DC-DC converter and linear regulator active.
Linear regulator starts after DC-DC converter.
(1)
(2)
FUNCTION
The LILO is turned on via a small NMOS device supplied by VIN_LDO . The maximum current is 50 mA when this small NMOS is ON. If
higher current > 50 mA is desired this condition must be done: EN_DC = HIGH .
When the switcher is enabled, a transition occurs from the small NMOS to a larger NMOS. The transition occurs when VIN_LILO >
VOUT_LILO + 250 mV. If VIN_LILO < VOUT_LILO + 150 mV, the LILO switches back to small NMOS (switcher EN = low).
1.8V
VOUT-DCDC
0V
1.2V
VOUT-LILO
0V
LARGE NMOS
IOUT-LILO > 50 mA
FET OF LILO (SMALL NMOS)
IOUT-LILO 7 50 mA
(SMALL NMOS TO LARGE NMOS TRANSITION)
Figure 15. Mode Transition
16
Submit Documentation Feedback
Copyright © 2008–2016, Texas Instruments Incorporated
Product Folder Links: LM3686
LM3686
www.ti.com
SNVS520F – AUGUST 2008 – REVISED NOVEMBER 2016
9 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
9.1 Application Information
The LM3686 is a step-down DC-DC converter with integrated low-dropout linear regular and a low-noise linear
regulator optimized for powering ultra-low voltage circuits from a single Li-Ion cell or 3-cell NiMH/NiCd batteries.
It provides three outputs with combined load current up to 900 mA over an input-voltage range from 2.7 V to 5.5
V.
9.2 Typical Application
VBATT
2.7 V to 5.5 V
4.7 PF, 0603
EN_DCDC
LM3686
PGND
1 PH
SW
3 MHz
DC-DC
1.8 V
FB_DCDC
VIN_LILO
10 PF
0603
PGND
EN_LILO
Dual Rail
LILO
350 mA
LILO
EN_LDO
2.2 PF,
0402
VIN_LDO
350 mA
QGND
1.2 V to 3.3 V
LDO
Linear Regulator
300 mA
300 mA
1 PF,
0402
1 PF, 0402
PGND
0.7 V to 2 V
QGND
QGND
QGND
Copyright © 2016, Texas Instruments Incorporated
Figure 16. LM3686 Typical Application
9.2.1 Design Requirements
For typical step-down DC-DC converter applications, use the parameters listed in Table 2.
Table 2. Design Parameters
DESIGN PARAMETER
EXAMPLE VALUE
Input voltage
2.7 V to 5.5 V
Output voltage
1.8 V
Output current
100 mA
Minimum switching frequency
2.55 MHz
RMS noise, 10 Hz to100 kHz
166 μVRMS
PSRR at 100 kHz
60 dB
Submit Documentation Feedback
Copyright © 2008–2016, Texas Instruments Incorporated
Product Folder Links: LM3686
17
LM3686
SNVS520F – AUGUST 2008 – REVISED NOVEMBER 2016
www.ti.com
9.2.2 Detailed Design Procedure
9.2.2.1 Application Selection
TI strongly recommends selection of the required components for the LM3686 device as described within the
data sheet. If other components are selected, the device will not perform up to standards, and electrical
characteristics cannot be ensured.
9.2.2.2 Inductor Selection
There are two main considerations when choosing an inductor: the inductor must not saturate, and the inductor
current ripple must be small enough to achieve the desired output voltage ripple. Different saturation current
rating specifications are followed by different manufacturers so attention must be given to details. Saturation
current ratings are typically specified at 25°C. However, ratings at the maximum ambient temperature of
application should be requested from the manufacturer. The minimum value of inductance to ensure good
performance is 0.7 µH at ILIM (typical) DC current over the ambient temperature range. Shielded inductors radiate
less noise and are preferred. There are two methods to choose the inductor saturation current rating.
9.2.2.2.1 Method 1
The saturation current must be greater than the sum of the maximum load current and the worst case averageto-peak inductor current. This can be written as:
ISAT > IOUT_DCDC_MAX + IRIPPLE
(1)
where
ISAT ! IOUTMAX + IRIPPLE
where IRIPPLE =
•
•
•
•
•
§VBATT - VOUT· x § VOUT · x § 1 ·
¨ 2 x L ¸ ¨VBATT¸ ¨ f ¸
©
¹ ©
¹ © ¹
IRIPPLE: average-to-peak inductor current
IOUT_DCDCMAX: maximum load current (600 mA)
VBATT: maximum input voltage in application
L: minimum inductor value including worst case tolerances (30% drop can be considered for Method 1)
f: minimum switching frequency (2.55 MHz)
(2)
9.2.2.2.2 Method 2
A more conservative and recommended approach is to choose an inductor that has a saturation current rating
greater than the maximum current limit of 1375 mA.
A 1-µH inductor with a saturation current rating of at least 1375 mA is recommended for most applications.
Resistance of the inductor must less than 0.3 Ω for good efficiency. Table 3 lists suggested inductors and
suppliers. For low-cost applications, an unshielded bobbin inductor could be considered. For noise critical
applications, a toroidal or shielded- bobbin inductor should be used. A good practice is to lay out the board with
overlapping footprints of both types for design flexibility. This allows substitution of a low-noise shielded inductor,
in the event that noise from low-cost bobbin models is unacceptable.
Table 3. Suggested Inductors and Their Suppliers
MODEL
VENDOR
DIMENSIONS L × W × H (mm)
DCR (maximum)
BRL2518T1R0M
TAIYO YUDEN
2.5 × 1.8 × 1.2
80
MDT2520CR1R0M
TOKO
2.5 × 2.0 × 1.0
80
KSLI252010AG1R0
HITACHI METALS
2.5 × 2.0 × 1.0
75
9.2.2.3 External Capacitors
As common with most regulators, the LM3686 requires external capacitors to ensure stable operation. The
LM3686 is specifically designed for portable applications requiring minimum board space and the smallest size
components. These capacitors must be correctly selected for good performance.
18
Submit Documentation Feedback
Copyright © 2008–2016, Texas Instruments Incorporated
Product Folder Links: LM3686
LM3686
www.ti.com
SNVS520F – AUGUST 2008 – REVISED NOVEMBER 2016
9.2.2.4 Input Capacitor Selection
9.2.2.4.1 CIN_DC-DC
A ceramic input capacitor of 4.7 µF, 6.3 V is sufficient for most applications. Place the input capacitor as close as
possible to the VBATT pin of the device. A larger value may be used for improved input voltage filtering. Use X7R
or X5R types; do not use Y5V. DC bias characteristics of ceramic capacitors must be considered when selecting
case sizes like 0805 and 0603. The minimum input capacitance to ensure good performance is 2.2 µF at 3-V DC
bias; 1.5 µF at 5-V DC bias including tolerances and over ambient temperature range. The input filter capacitor
supplies current to the PFET switch of the LM3686 DC-DC converter in the first half of each cycle and reduces
voltage ripple imposed on the input power source. The low ESR of a ceramic capacitor provides the best noise
filtering of the input voltage spikes due to this rapidly changing current. Select a capacitor with sufficient ripple
current rating. The input current ripple can be calculated as:
IRMS = IOUTMAX x
r=
VOUT
VBATT
§
©
x ¨1 -
VOUT
VBATT
2
+
r
12
·
¸
¹
(VBATT - VOUT) x VOUT
L x f x IOUTMAX x VBATT
The worst case is when VBATT = 2 x VOUT
(3)
9.2.2.4.2 CIN_LILO
If the LILO is used as post regulation no additional capacitor is needed at VIN_LILO as the output filter capacitor of
the DC-DC converter is close by and therefore sufficient.
In case of independent mode use, a 1-µF ceramic capacitor is recommended at VIN_LILO if no other filter capacitor
is present in the VIN_LILO supply path. This capacitor must be located a distance of not more than 1 cm from the
VIN_LILO input pin and returned to QGND.
9.2.2.4.3 CIN_LDO
An input capacitor is required for stability. TI recommends using a 1-µF ceramic capacitor and connected
between the VIN_LDO and QGND.
9.2.2.5 Output Capacitor
9.2.2.5.1 COUT_DCDC
A ceramic output capacitor of 10 µF, 6.3 V is sufficient for most applications. Use X7R or X5R types; do not use
Y5V. DC bias characteristics of ceramic capacitors must be considered when selecting case sizes like 0805 and
0603. DC bias characteristics vary from manufacturer to manufacturer, and DC bias curves should be requested
from them as part of the capacitor selection process.
The minimum output capacitance to ensure good performance is 5.75 µF at 1.8-V DC bias including tolerances
and over ambient temperature range. The output filter capacitor smooths out current flow from the inductor to the
load, helps maintain a steady output voltage during transient load changes and reduces output voltage ripple.
These capacitors must be selected with sufficient capacitance and sufficiently low equivalent series resistance
(ESR) to perform these functions.
The output voltage ripple is caused by the charging and discharging of the output capacitor and by the RESR and
can be calculated as:
Voltage peak-to-peak ripple due to capacitance can be expressed as:
VPP-C =
IRIPPLE
4xfxC
(4)
Voltage peak-to-peak ripple due to ESR can be expressed as:
VPP-ESR = (2 × IRIPPLE) × RESR
(5)
Submit Documentation Feedback
Copyright © 2008–2016, Texas Instruments Incorporated
Product Folder Links: LM3686
19
LM3686
SNVS520F – AUGUST 2008 – REVISED NOVEMBER 2016
www.ti.com
Because these two components are out of phase, the root mean squared (RMS) value can be used to get an
approximate value of peak-to-peak ripple. The peak-to-peak ripple voltage, RMS value can be expressed as:
VPP-RMS =
VPP-C2 + VPP-ESR2
(6)
Note that the output voltage ripple is dependent on the inductor current ripple and the ESR of the output
capacitor (RESR). The RESR is frequency dependent (as well as temperature dependent); make sure the value
used for calculations is at the switching frequency of the part.
9.2.2.5.2 COUT_LILO
The linear regulator is designed specifically to work with very small ceramic output capacitors. A ceramic
capacitor (dielectric types X7R, Z5U, or Y5V) in the 2.2-µF range (up to 10 µF) and with an ESR between 3 mΩ
to 300 mΩ is suitable as COUT_LIN in the LM3686 application circuit.
This capacitor must be located a distance of not more than 1 cm from the VOUT_LILO pin and returned to a clean
analog ground. Tantalum or film capacitors may also be used at the device output, VOUT_LILO but these are not as
attractive for reasons of size and cost (see Table 4).
9.2.2.5.3 COUT_LDO
CAP VALUE (% of Nom. 1 PF)
A ceramic capacitor in the 1-uF to 2.2-uF range, and with ESR between 5 mΩ to 500 mΩ, is suitable for the
linear regulator. Connect this output capacitor no more than 1 cm from VOUT_LDO and QGND.
0603, 10V, X5R
100%
80%
60%
0402, 6.3V, X5R
40%
20%
0
1.0
2.0
3.0
4.0
5.0
DC BIAS (V)
Figure 17. Graph Showing A Typical Variation In Capacitance vs DC Bias
Table 4. Suggested Capacitors and Their Suppliers
CAPACITANCE (µF)
MODEL
VOLTAGE RATING (V)
Vendor
Type
Case Size / Inch (mm)
20
10
C1608X5R0J106K
6.3
TDK
Ceramic, X5R
0603 (1608)
4.7
C1608X5R0J475
6.3
TDK
Ceramic, X5R
0603 (1608)
2.2
C1608X5R0J225M
6.3
TDK
Ceramic, X5R
0603 (1608)
1
C1005JB0J105KT
6.3
TDK
Ceramic, X5R
0402 (1005)
Submit Documentation Feedback
Copyright © 2008–2016, Texas Instruments Incorporated
Product Folder Links: LM3686
LM3686
www.ti.com
SNVS520F – AUGUST 2008 – REVISED NOVEMBER 2016
9.2.3 Application Curves
Figure 18. VBATT Line Transient Response
Figure 19. Line Transient Response
PFM Mode: 1 mA to
150 mA
PWM Mode: 100 mA to
350 mA
Figure 20. Load Transient Response DC-DC
LILO 50 mA to 250 mA
Figure 21. Load Transient Response DC-DC
LDO 100 mA to 250 mA
Figure 22. Load Transient Response
Figure 23. Load Transient Response
Submit Documentation Feedback
Copyright © 2008–2016, Texas Instruments Incorporated
Product Folder Links: LM3686
21
LM3686
SNVS520F – AUGUST 2008 – REVISED NOVEMBER 2016
www.ti.com
10 Power Supply Recommendations
The LM3686 requires a single supply input voltage. This voltage can range between 2.7 V to 5.5 V and must be
able to supply enough current for a given application.
11 Layout
11.1
Layout Guidelines
PC board layout is an important part of DC-DC converter design. Poor board layout can disrupt the performance
of a DC-DC converter and surrounding circuitry by contributing to EMI, ground bounce, and resistive voltage loss
in the traces. These can send erroneous signals to the DC-DC converter device, resulting in poor regulation or
instability. Implement good layout for the LM3686 by following a few simple design rules:
1. Place the LM3686, inductor,and filter capacitor close together and make the traces short. The traces
between these components carry relatively high switching currents and act as antennas. Following this rule
reduces radiated noise. Special care must be given to place the input filter capacitor very close to the VBATT
and PGND pin. Place the output capacitor of the linear regulator close to the output pin.
2. Arrange the components so that the switching current loops curl in the same direction. During the first half of
each cycle, current flows from the input filter capacitor through the LM3686 and inductor to the output filter
capacitor and back through ground, forming a current loop. In the second half of each cycle, current is pulled
up from ground through the LM3686 by the inductor to the output filter capacitor and then back through
ground forming a second current loop. Routing these loops so the current curls in the same direction
prevents magnetic field reversal between the two half-cycles and reduces radiated noise.
3. Connect the ground pins of the LM3686 and filter capacitors together using generous component-side
copper fill as a pseudo-ground plane. Then, connect this to the ground-plane (if one is used) with several
vias. This reduces ground-plane noise by preventing the switching currents from circulating through the
ground plane. It also reduces ground bounce at the LM3686 by giving it a low impedance ground connection.
Route SGND to the ground-plane by a separate trace.
4. Use wide traces between the power components and for power connections to the DC-DC converter circuit.
This reduces voltage errors caused by resistive losses across the traces.
5. Route noise sensitive traces, such as the voltage feedback path (FB_DCDC), away from noisy traces
between the power components. The voltage feedback trace must remain close to the LM3686 circuit, must
be direct, and must be routed opposite to noisy components. This reduces EMI radiated onto the DC-DC
converter voltage feedback trace. A good approach is to route the feedback trace on another layer and to
have a ground plane between the top layer and layer on which the feedback trace is routed.
6. Place noise sensitive circuitry, such as radio IF blocks, away from the DC-DC converter, CMOS digital blocks
and other noisy circuitry. Interference with noise sensitive circuitry in the system can be reduced through
distance.
In mobile phones, for example, a common practice is to place the DC-DC converter on one corner of the board,
arrange the CMOS digital circuitry around it (since this also generates noise), and then place sensitive preamplifiers and IF stages on the diagonally opposing corner. Often, the sensitive circuitry is shielded with a metal
plane; power to it is post-regulated to reduce conducted noise, a good field of application for the on-chip lowdropout linear regulator.
22
Submit Documentation Feedback
Copyright © 2008–2016, Texas Instruments Incorporated
Product Folder Links: LM3686
LM3686
www.ti.com
SNVS520F – AUGUST 2008 – REVISED NOVEMBER 2016
11.2 Layout Example
Figure 24. LM3686 Layout
11.3 DSBGA Package Assembly and Use
Use of the DSBGA package requires specialized board layout, precision mounting and careful re-flow
techniques, as detailed in AN-1112 DSBGA Wafer Level Chip Scale Package. Refer to the section Surface
Mount Technology (SMD) Assembly Considerations. For best results in assembly, alignment ordinals on the PC
board must be used to facilitate placement of the device. The pad style used with DSBGA package must be the
non-solder mask defined (NSMD) type. This means that the solder-mask opening is larger than the pad size.
This prevents a lip that otherwise forms if the solder mask and pad overlap, from holding the device off the
surface of the board and interfering with mounting. See AN-1112 DSBGA Wafer Level Chip Scale Package for
specific instructions how to do this. The 12-pin package used for LM3686 has 300 micron solder balls and
requires 275 micron pads for mounting on the circuit board. The trace to each pad must enter the pad with a 90°
entry angle to prevent debris from being caught in deep corners. Initially, the trace to each pad must not exceed
183 micron, for a section approximately 183 micron long or longer, as a thermal relief —then each trace must
neck up or down to its optimal width. The important criteria is symmetry. This ensures the solder bumps on the
LM3686 re-flow evenly and that the device solders level to the board. In particular, special attention must be paid
to the pads for bumps A1 and B1 because PGND and VBATT are typically connected to large copper planes,
inadequate thermal relief can result in late or inadequate re-flow of these bumps. The DSBGA package is
optimized for the smallest possible size in applications with red or infrared opaque cases. Because the DSBGA
package lacks the plastic encapsulation characteristic of larger devices, it is vulnerable to light. Backside
metallization and/or epoxy coating, along with frontside shading by the printed circuit board, reduce this
sensitivity. However, the package has exposed die edges. In particular, DSBGA devices are sensitive to light, in
the red and infrared range, shining on the exposed die edges of the package.
Submit Documentation Feedback
Copyright © 2008–2016, Texas Instruments Incorporated
Product Folder Links: LM3686
23
LM3686
SNVS520F – AUGUST 2008 – REVISED NOVEMBER 2016
www.ti.com
12 Device and Documentation Support
12.1 Device Support
12.1.1 Third-Party Products Disclaimer
TI'S PUBLICATION OF INFORMATION REGARDING THIRD-PARTY PRODUCTS OR SERVICES DOES NOT
CONSTITUTE AN ENDORSEMENT REGARDING THE SUITABILITY OF SUCH PRODUCTS OR SERVICES
OR A WARRANTY, REPRESENTATION OR ENDORSEMENT OF SUCH PRODUCTS OR SERVICES, EITHER
ALONE OR IN COMBINATION WITH ANY TI PRODUCT OR SERVICE.
12.2 Related Documentation
For additional information, see the following:
AN-1112 DSBGA Wafer Level Chip Scale Package
12.3 Receiving Notification of Documentation Updates
To receive notification of documentation updates, navigate to the device product folder on ti.com. In the upper
right corner, click on Alert me to register and receive a weekly digest of any product information that has
changed. For change details, review the revision history included in any revised document.
12.4 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
12.5 Trademarks
E2E is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
12.6 Electrostatic Discharge Caution
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
12.7 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
13 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
24
Submit Documentation Feedback
Copyright © 2008–2016, Texas Instruments Incorporated
Product Folder Links: LM3686
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
(2)
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
(4/5)
(6)
LM3686TLE-AADW/NOPB
ACTIVE
DSBGA
YZR
12
250
RoHS & Green
SNAGCU
Level-1-260C-UNLIM
-30 to 85
SUEB
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of