LMX2352SLBX

LMX2350,LMX2352 LMX2350/LMX2352 PLLatinum Fractional N RF / Integer N IF Dual Low Power Frequency Synthesizer Literature Number: SNAS022B LMX2350/LMX2352 PLLatinum Fractional N RF / Integer N IF Dual Low Power Frequency Synthesizer LMX2350 2.5 GHz/550 MHz LMX2352 1.2 GHz/550 MHz LMX2352 family features very low current consumption; typically LMX2350 (2.5 GHz) 6.5 mA, LMX2352 (1.2 GHz) 4.75 mA at 3.0V. The LMX2350/2352 are available in a 24-pin TSSOP and 24-pin CSP surface mount plastic package. General Description The LMX2350/2352 is part of a family of monolithic integrated fractional N/ Integer N frequency synthesizers designed to be used in a local oscillator subsystem for a radio transceiver. It is fabricated using National’s 0.5µ ABiC V silicon BiCMOS process. The LMX2350/2352 contains dual modulus prescalers along with modulo 15 or 16 fractional compensation circuitry in the RF divider. A 16/17 or 32/33 prescale ratio can be selected for the LMX2350, and the LMX2352 provides 8/9 or 16/17 prescale ratios. The IF circuitry for both the LMX2350 and LMX2352 contains an 8/9 prescaler, and is fully programmable. Using a fractional N phase locked loop technique, the LMX2350 /52 can generate very stable low noise control signals for UHF and VHF voltage controlled oscillators (VCOs). For the RF PLL, a highly flexible 16 level programmable charge pump supplies output current magnitudes from 100µA to 1.6mA. Two uncommitted CMOS outputs can be used to provide external control signals, or configured to FastLock™ mode. Serial data is transferred into the LMX2350/2352 via a three wire interface (Data, LE, Clock). Supply voltage can range from 2.7 V to 5.5 V. The LMX2350/ Features n 2.7 V to 5.5 V operation n Low current consumption LMX2350: Icc = 6.75mA typ at 3v LMX2352: Icc = 5.00mA typ at 3v n Programmable or logical power down mode Icc = 5 µA typ at 3v n Modulo 15 or 16 fractional RF N divider supports ratios of 1, 2, 3, 4, 5, 8, 15, or 16 n Programmable charge pump current levels RF 100µA to 1.6mA in 100µA steps IF 100µA or 800 µA n Digital filtered lock detect Applications n Portable wireless communications (PCS/PCN, cordless) n Dual mode cellular telephone systems n Zero blind slot TDMA systems n Spread spectrum communication systems (CDMA) n Cable TV Tuners (CATV) Block Diagram DS100831-1 © 2001 National Semiconductor Corporation DS100831 www.national.com LMX2350/LMX2352 PLLatinum Fractional N RF / Integer N IF Dual Low Power Frequency Synthesizer March 2001 LMX2350/LMX2352 Connection Diagrams DS100831-2 Order Number LMX2350TM or LMX2352TM NS Package Number MTC24 DS100831-22 Pin Descriptions Pin No. for CSP Package Pin No. for TSSOP package 24 1 Pin Name I/O Description 1 OUT0 O Programmable CMOS output. Level of the output is controlled by IF_N [17] bit. 2 VccRF - RF PLL power supply voltage input. Must be equal to VccIF. May range from 2.7 V to 5.5 V. Bypass capacitors should be placed as close as possible to this pin and be connected directly to the ground plane. 2 3 VpRF - Power supply for RF charge pump. Must be ≥VccRF and VccIF. 3 4 CPoRF O RF charge pump output. Connected to a loop filter for driving the control input of an external VCO. 4 5 GND - Ground for RF PLL digital circuitry. 5 6 fin RF I RF prescaler input. Small signal input from the VCO. 6 7 fin RF I RF prescaler complimentary input. A bypass capacitor should be placed as close as possible to this pin and be connected directly to the ground plane. 7 8 GND - 8 9 OSCx I/O www.national.com Ground for RF PLL analog circuitry. Dual mode oscillator output or RF R counter input. Has a Vcc/2 input threshold when configured as an input and can be driven from an external CMOS or TTL logic gate. Can also be configured as an output to work in conjunction with OSCin to form a crystal oscillator. (See functional description 1.1 and programming description 3.1.) 2 (Continued) Pin No. for CSP Package Pin No. for TSSOP package 9 10 OSCin I Oscillator input which can be configured to drive both the IF and RF R counter inputs or only the IF R counter depending on the state of the OSC programming bit. (See functional description 1.1 and programming description 3.1.) 10 11 FoLD O Multiplexed output of N or R divider and RF/IF lock detect. Active High/Low CMOS output except in analog lock detect mode. (See programming description 3.1.5.) 11 12 RF_EN I RF PLL Enable. Powers down RF N and R counters, prescaler, and will TRI-STATE ® the charge pump output when LOW. Bringing RF_EN high powers up RF PLL depending on the state of RF_CTL_WORD. (See functional description 1.9.) 12 13 IF_EN I IF PLL Enable. Powers down IF N and R counters, prescaler, and will TRI-STATE the charge pump output when LOW. Bringing IF_EN high powers up IF PLL depending on the state of IF_CTL_WORD. (See functional description 1.9.) 13 14 CLOCK I High impedance CMOS Clock input. Data for the various counters is clocked into the 24 - bit shift register on the rising edge. 14 15 DATA I Binary serial data input. Data entered MSB first. The last two bits are the control bits. High impedance CMOS input. 15 16 LE I Load enable high impedance CMOS input. Data stored in the shift registers is loaded into one of the 4 internal latches when LE goes HIGH. (See functional description 1.7.) 16 17 GND - Ground for IF analog circuitry. 17 18 fin IF I IF prescaler complimentary input. A bypass capacitor should be placed as close as possible to this pin and be connected directly to the ground plane. 18 19 fin IF I IF prescaler input. Small signal input from the VCO. 19 20 GND - Ground for IF digital circuitry. 20 21 CPoIF O IF charge pump output. For connection to a loop filter for driving the input of an external VCO. 21 22 VpIF - Power supply for IF charge pump. Must be ≥ VccRF and VccIF. 22 23 VccIF - IF power supply voltage input. Must be equal to VccRF . Input may range from 2.7 V to 5.5 V. Bypass capacitors should be placed as close as possible to this pin and be connected directly to the ground plane. 23 24 OUT1 O Programmable CMOS output. Level of the output is controlled by IF_N [18] bit. Pin Name I/O Description 3 www.national.com LMX2350/LMX2352 Pin Descriptions LMX2350/LMX2352 Absolute Maximum Ratings (Note 1) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Value Parameter Symbol Min Max Units VccRF -0.3 6.5 V VccIF -0.3 6.5 V VpRF -0.3 6.5 V VpIF -0.3 6.5 V Voltage on any pin with GND = 0 volts Vi -0.3 Vcc + 0.3 V Storage Temperature Range Ts -65 Lead Temperature (Solder 4 sec.) TL Power Supply Voltage Typ +150 C˚ +260 C˚ Recommended Operating Conditions Value Parameter Power Supply Voltage Symbol Min Max Units VccRF 2.7 5.5 V VccIF VccRF VccRF V VpRF Vcc 5.5 V VpIF Vcc 5.5 V TA -40 + 85 C Operating Temperature Note 1: “Absolute Maximum Ratings” indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed. Electrical Characteristics Symbol Typ Note 2: This Device is a high performance RF integrated circuit with an ESD rating < 2 KV and is ESD sensitive. Handling and assembly of this device should only be done at ESD-free workstations. (VccRF = VccIF = VPRF = VPIF = 3.0V; −40˚ C < TA < 85˚ C except as specified) Parameter Conditions Min Typ Max Units General Icc Power Supply Current ICC-PWDN Power Down Current fin RF RF Operating LMX2350 RF and IF, Vcc = 2.7V to 5.5V 6.5 8.75 mA LMX2352 RF and IF, Vcc = 2.7V to 5.5V 4.75 6.0 mA LMX2350/52 IF only, Vcc = 2.7V to 5.5V 1 2.2 mA 20 µA LMX2350 Prescaler = 32 (Note 3) 1.2 2.5 GHz Prescaler = 16 (Note 3) 0.5 1.2 GHz Prescaler = 16 (Note 3) 0.5 1.2 GHz Prescaler = 8 (Note 3) 0.25 0.5 GHz 10 550 MHz No load on OSCx (Note 3) 2 50 MHz With resonator load on OSCx (Note 3) 2 20 MHz RF_EN = IF_EN = LOW Frequency LMX2352 fin IF IF Operating Frequency fOSC Oscillator Frequency 5 fφ Phase Detector Frequency RF and IF 10 MHz Pfin RF RF Input Sensitivity 2.7V≤VCC ≤3.0V −15 0 dBm 3.0V≤VCC ≤5.5V −10 0 dBm Pfin IF IF Input Sensitivity 2.7 V≤VCC≤ 5.5V −10 0 dBm VOSC Oscillator Sensitivity OSCin, OSCx 0.5 VCC VPP www.national.com 4 (VccRF = VccIF = VPRF = VPIF = 3.0V; −40˚ C < TA < 85˚ C except as specified) (Continued) All Min/Max specifications are guaranteeed by design, or test, or statistical methods. Symbol Parameter Conditions Min Typ Max Units Charge Pump ICPo-source RF ICPo-sink RF ICPo-source RF Charge Pump Output Current (see Programming Description 3.2.2) VCPo Vp/2, RF_CP_WORD = 0000 IF Charge Pump Output Current (see Programming Description 3.1.4) VCPo = Vp/2, CP_GAIN_8 = 0 −100 µA VCPo = Vp/2, RF_CP_WORD = 0000 100 µA VCPo = Vp/2, RF_CP_WORD = 1111 −1.6 mA RF ICPo-sink RF ICPo-source IF ICPo-sink IF ICPo-source VCPo = Vp/2, RF_CP_WORD = 1111 1.6 mA −100 µA VCPo = Vp/2, CP_GAIN_8 = 0 100 µA VCPo = Vp/2, CP_GAIN_8 = 1 −800 µA VCPo = Vp/2, CP_GAIN_8 = 1 800 µA IF ICPo-sink IF ICPo-Tri Charge Pump TRI-STATE Current 0.5 ≤ VCPo ≤ Vp - 0.5 -40˚ C < TA < 85˚ C ICPo-sink vs. ICPo-source CP Sink vs. Source Mismatch VCPo = Vp/2 TA = 25˚ C RFICPo = 400 µA - 1.6 mA ICPo vs. VCPo CP Current vs. Voltage 0.5 ≤ VCPo ≤ Vp 0.5 TA = 25˚ C RFICPo = 800 µA - 1.6 mA ICPo vs. T CP Current vs Temperature VCPo = Vp/2 -40˚ C < TA < 85˚ C -2.5 2.5 nA 3 10 % 4 15 % 8 % Digital Interface VIH High-level Input Voltage (Note 4) VIL Low-level Input Voltage (Note 4) IIH High-level Input Current VIH = VCC = 5.5 V, (Note 4) −1.0 IIL Low-level Input Current VIL = 0, VCC = 5.5 V, (Note 4) −1.0 IIH Oscillator Input Current VIH = VCC = 5.5 V IIL Oscillator Input Current VIL = 0, VCC = 5.5 V −100 µA VOH High-level Output Voltage IOH = −500 µA VCC −0.4 V VOL High-level Output Voltage IOL = 500 µA 0.8 Vcc V 0.2 Vcc V 1.0 µA 1.0 µA 100 µA 0.4 V MICROWIRE Timing tCS Data to Clock Setup Time See Data Input Timing 50 ns tCH Data to Clock Hold Time See Data Input Timing 10 ns tCWH Clock Pulse Width High See Data Input Timing 50 ns tCWL Clock Pulse Width Low See Data Input Timing 50 ns tES Clock to Load Enable Set Up Time See Data Input Timing 50 ns tEW Load Enable Pulse Width See Data Input Timing 50 ns Note 3: Minimum operating frequencies are not production tested - only characterized. Note 4: except fin, OSCin and OSCx 5 www.national.com LMX2350/LMX2352 Electrical Characteristics LMX2350/LMX2352 Charge Pump Current Specification Definitions DS100831-7 I1 = CP sink current at VDo = Vp − ∆V I2 = CP sink current at VDo = Vp/2 I3 = CP sink current at VDo = ∆V I4 = CP source current at VDo = Vp − ∆V I5 = CP source current at VDo = Vp/2 I6 = CP source current at VDo = ∆V ∆V = Voltage offset from positive and negative rails. Dependent on VCO tuning range relative to VCC and ground. Typical values are between 0.5V and 1.0V. Note 5: IDo vs VDo = Charge Pump Output Current magnitude variation vs Voltage = [1⁄2 * {||1| − ||3|}]/[1⁄2 * {||1| + ||3|}] * 100% and [1⁄2 * {||4| − ||6|}]/[1⁄2 * {||4| + ||6|}] * 100% Note 6: IDo-sink vs IDo-source = Charge Pump Output Current Sink vs Source Mismatch = [||2| − ||5|]/[1⁄2 * {||2| + ||5|}] * 100% Note 7: IDo vs TA = Charge Pump Output Current magnitude variation vs Temperature = [||2 @ temp| − ||2 @ 25˚C|]/||2 @ 25˚C| * 100% and [||5 @ temp| − ||5 @ 25˚C|]/||5 @ 25˚C| * 100% www.national.com 6 LMX2350/LMX2352 RF Sensitivity Test Block Diagram DS100831-8 Note: N = 10,000 R = 50 P = 32 Note: Sensitivity limit is reached when the error of the divided RF output, FoLD, is ≥ 1 Hz. Typical Performance Characteristics ICC vs VCC LMX2350 ICC vs VCC LMX2352 DS100831-9 ICPO TRI-STATE vs CPO Voltage DS100831-10 Charge Pump Current vs CPO Voltage RF_CP_WORD = 0000 and 0111 IF CP_GAIN_8 = 0 and 1 DS100831-11 DS100831-12 7 www.national.com LMX2350/LMX2352 Typical Performance Characteristics (Continued) Charge Pump Current vs CPO Voltage RF_CP_WORD = 0011 and 1111 Sink vs Source Mismatch (See (Note 6) under Charge Pump Current Specification Definitions) DS100831-13 DS100831-14 RF Input Impedance VCC = 2.7V to 5.5V, fIN = 50 MHz to 3 GHz (fIN Capacitor = 100 pF) IF Input Impedance VCC = 2.7V to 5.5V, fIN = 10 MHz to 1 GHz (fIN Capacitor = 100 pF) DS100831-15 www.national.com DS100831-16 8 (Continued) LMX2350 RF Sensitivity vs Frequency LMX2352 RF Sensitivity vs Frequency DS100831-18 DS100831-17 IF Input Sensitivity vs Frequency LMX2350/LMX2352 Typical Performance Characteristics Oscillator Input Sensitivity vs Frequency DS100831-19 DS100831-20 LMX2350 VP Voltage vs VP Load Current in Vdoubler Mode, T = 25˚C DS100831-21 9 www.national.com LMX2350/LMX2352 and a 10 bit B Counter. The LMX2350 is capable of operating from 500 MHz to 1.2 GHz with the 16/17 prescaler offering a continuous integer divide range from 272 to 16399, and 1.2 GHz to 2.5 GHz with the 32/33 prescaler offering a continuous integer divide range from 1056 to 32767. The LMX2352 RF N counter is 18 bits with 14 bits integer divide and 4 bits fractional. The integer part is configured as a 4 bit A Counter and a 10 bit B Counter. The LMX2352 is capable of operating from 250 MHz to 500 MHz with the 8/9 prescaler offering a continuous integer divide range from 72 to 8199, and 500MHz to 1.2 GHz with 16/17 prescaler offering a continuous integer divide range from 272 to 16383. The RF counters for the LMX2350 family also contain fractional compensation, programmable in either 1/15 or 1/16 modes. Both LMX2350 and LMX2352 IF N counters are 15 bit integer dividers configured with a 3 bit A Counter and a 12 bit B Counter offering a continuous integer divide range from 56 to 32,767 over the frequency range of 10 MHz to 550 MHz. The IF N counters do not include fractional compensation. Functional Description 1.0 General The basic phase-lock-loop (PLL) configuration consists of a high-stability crystal reference oscillator, a frequency synthesizer such as the National Semiconductor LMX2350/52, a voltage controlled oscillator (VCO), and a passive loop filter. The frequency synthesizer includes a phase detector, current mode charge pump, as well as programmable reference [R] and feedback [N] frequency dividers. The VCO frequency is established by dividing the crystal reference signal down via the R counter to obtain a frequency that sets the comparison frequency. This reference signal, fr, is then presented to the input of a phase/frequency detector and compared with another signal, fp, the feedback signal, which was obtained by dividing the VCO frequency down by way of the N counter and fractional circuitry. The phase/frequency detector’s current source outputs pump charge into the loop filter, which then converts the charge into the VCO’s control voltage. The phase/frequency comparator’s function is to adjust the voltage presented to the VCO until the feedback signal’s frequency (and phase) match that of the reference signal. When this ’phase-locked’ condition exists, the RF VCO’s frequency will be N+F times that of the comparison frequency, where N is the integer divide ratio and F is the fractional component. The fractional synthesis allows the phase detector frequency to be increased while maintaining the same frequency step size for channel selection. The division value N is thereby reduced giving a lower phase noise referred to the phase detector input, and the comparison frequency is increased allowing faster switching times. 1.3.1 Prescaler The RF and IF inputs to the prescaler consist of fin and /fin; which are complimentary inputs to differential pair amplifiers. The complimentary inputs are internally coupled to ground with a 10 pF capacitor. These inputs are typically AC coupled to ground through external capacitors as well. The input buffer drives the A counter’s ECL D-type flip flops in a dual modulus configuration. A 16/17 or 32/33 prescale ratio can be selected for the LMX2350, and the lower frequency LMX2352 provides 8/9 or 16/17 prescale ratios. The IF circuitry for both the LMX2350 and LMX2352 contain an 8/9 prescaler. The prescaler clocks the subsequent CMOS flipflop chain comprising the fully programmable A and B counters. 1.1 Reference Oscillator Inputs The reference oscillator frequency for the RF and IF PLL’s is provided by either an external reference through the OSCin pin and OSCx pin, or an external crystal resonator across the OSCin and OSCx pins. OSCin/OSCx block can operate to 50MHz with an input sensitivity of 0.5Vpp. The OSC bit (see programming description 3.1.1), selects whether the oscillator input pins OSCin and OSCx drive the IF and RF R counters separately (Low) or by a common input signal path (Hi). The common OSC mode allows the user to form a local crystal oscillator circuit or drive the OSCin pin from an external signal source. When a crystal resonator is connected between OSCin and OSCx along with 2 external capacitors to form a crystal oscillator both reference chains are driven simultaneously. When a TCXO is connected only at the OSCin input pin and not at the OSCx pin, the TCXO drives both IF R counter and RF R counter. When configured as separate inputs, the OSCin pin drives the IF R counter while the OSCx drives the RF R counter. The inputs have a Vcc/2 input threshold and can be driven from an external CMOS or TTL logic gate. 1.3.2 Fractional Compensation The fractional compensation circuitry of the LMX2350 and LMX2352 RF dividers allow the user to adjust the VCO’s tuning resolution in 1/16 or 1/15 increments of the phase detector comparison frequency. A 4 bit register is programmed with the fractions desired numerator, while another bit selects between fractional 15 and 16 modulo base denominator (see programming description 4.2.4). An integer average is accomplished by using a 4 bit accumulator. A variable phase delay stage compensates for the accumulated integer phase error, minimizing the charge pump duty cycle, and reducing spurious levels. This technique eliminates the need for compensation current injection in to the loop filter. Overflow signals generated by the accumulator are equivalent to 1 full VCO cycle, and result in a pulse swallow. 1.4 Phase/Frequency Detector The RF and IF phase(/frequency) detectors are driven from their respective N and R counter outputs. The maximum frequency at the phase detector inputs is about 10 MHz for some high frequency VCO due to the minimum continuous divide ratio of the dual modulus prescaler. For example if the phase detector frequency exceeds 2.37 MHz, there are higher chances of running into illegal divide ratios, because the mimimum continuous divide ratio of the LMX2350 with 32/33 prescaler is 1056. The phase detector outputs control the charge pumps. The polarity of the pump-up or pumpdown control is programmed using RF_PD_POL or IF_PD_POL depending on whether RF/IF VCO characteristics are positive or negative (see programming descriptions 3.1.4 1.2 Reference Dividers (R Counters) The RF and IF R Counters are clocked through the oscillator block either separately or in common. The maximum frequency is 50MHz. Both R Counters are 15 bit CMOS counters with a divide range from 3 to 32,767. (See programming description 3.1.3.) 1.3 Programmable Dividers (N Counters) The RF and IF N Counters are clocked by the small signal fin RF and fin IF input pins respectively. The LMX2350 RF N counter is 19 bits with 15 bits integer divide and 4 bits fractional. The integer part is configured as a 5 bit A Counter www.national.com 10 signal is also selectable. The lock detect output is always low when the PLL is in power down mode. See programming descriptions 3.1.5, 4.6 - 4.8 for more details. (Continued) and 3.2.2). The phase detector also receives a feedback signal from the charge pump, in order to eliminate dead zone. 1.9 Power Control Each PLL is individually power controlled by device enable pins or MICROWIRE power down bits. The enable pins override the power down bits except for the V2_EN bit. The RF_EN pin controls the RF PLL; IF_EN pin controls the IF PLL. When both pins are high, the power down bits determine the state of power control (see programming description 3.2.1.2). Activation of any PLL power down mode results in the disabling of the respective N counter and de-biasing of its respective Fin input (to a high impedance state). The R counter functionality also becomes disabled when the power down bit is activated. The reference oscillator block powers down and the OSCin pin reverts to a high impedance state when both RF and IF enable pins or power down bit’s are asserted, unless the V2_EN bit (RF_R[22]) is high. Power down forces the respective charge pump and phase comparator logic to a TRI-STATE condition. A power down counter reset function resets both N and R counters. Upon powering up the N counter resumes counting in “close” alignment with the R counter (The maximum error is one prescaler cycle). The MICROWIRE control register remains active and capable of loading and latching in data during all of the power down modes. 1.5 Charge Pump The phase detector’s current source outputs pump charge into an external loop filter, which then converts the charge into the VCO’s control voltage. The charge pumps steer the charge pump output, CPo, to Vcc (pump-up) or ground (pump-down). When locked, CPo is primarily in a TRI-STATE ® mode with small corrections. The RF charge pump output current magnitude is programmable from 100 µA to 1.6 mA in 100 µA steps as shown in table in programming description 3.2.2. The IF charge pump is set to either 100µA or 800µA levels using bit IF_R [19] (see programming description 3.1.4). 1.6 Voltage Doubler The VpRF pin is normally driven from an external power supply over a range of Vcc to 5.5v to provide current for the RF charge pump circuit. An internal voltage doubler circuit connected between the Vcc and VpRF supply pins alternately allows Vcc = 3v ( ± 10%) users to run the RF charge pump circuit at close to twice the Vcc power supply voltage. The voltage doubler mode is enabled by setting the V2_EN bit (RF_R [22]) to a HIGH level. The voltage doubler’s charge pump driver originates from the RF oscillator input (OSCx). The device will not totally powerdown until the V2_EN bit is programmed low. The average delivery current of the doubler is less than the instantaneous current demand of the RF charge pump when active and is thus not capable of sustaining a continuous out of lock condition. A large external capacitor connected to VpRF is therefore needed to control power supply droop when changing frequencies. Refer to the application note AN-1119 for more details. 1.7 MICROWIRE™ Serial Interface The programmable functions are accessed through the MICROWIRE serial interface. The interface is made of 3 functions: clock, data and latch enable (LE). Serial data for the various counters is clocked in from data on the rising edge of clock, into the 24- bit shift register. Data is entered MSB first. The last two bits decode the internal register address. On the rising edge of LE, data stored in the shift register is loaded into one of the 4 appropriate latches (selected by address bits). A complete programming description is included in the following sections. 1.8 Fo/LD Multifunction Output The Fo/LD output pin can deliver several internal functions including analog/digital lock detects, and counter outputs. See programming description 3.1.5 for more details. 1.8.1 Lock Detect A digital filtered lock detect function is included with each phase detector through an internal digital filter to produce a logic level output available on the Fo/LD output pin if selected. The lock detect output is high when the error between the phase detector inputs is less than 15 nsec for 5 consecutive comparison cycles. The lock detect output is low when the error between the phase detector outputs is more than 30 nsec for one comparison cycle. An analog lock detect 11 www.national.com LMX2350/LMX2352 Functional Description LMX2350/LMX2352 Programming Description 2.0 INPUT DATA REGISTER The descriptions below describe the 24-bit data register loaded through the MICROWIRE Interface. The data register is used to program the 15-bit IF_R counter register, and the 15-bit RF_R counter register, the 15-bit IF_N counter register, and the 19-bit RF_N counter register. The data format of the 24-bit data register is shown below. The control bits CTL [1:0] decode the internal register address. On the rising edge of LE, data stored in the shift register is loaded into one of the 4 appropriate latches (selected by address bits). Data is shifted in MSB first MSB LSB DATA [21:0] CTL [1:0] 23 2 1 0 2.1 Register Location Truth Table CTL [1:0] DATA Location 1 0 0 0 IF_R register 0 1 IF_N register 1 0 RF_R register 1 1 RF_N register 2.2 Register Content Truth Table First Bit IF_R REGISTER BIT LOCATION 23 22 21 20 19 OSC FRAC_16 FoLD IF_N IF_CTL_WORD RF_R DLL_MODE RF_N 18 17 IF_CP_WORD 3 2 1 0 0 0 IF_NB_CNTR RF_CP_WORD RF_CTL_WORD 4 IF_R_CNTR CMOS V2_EN Last Bit 16 15 14 13 12 11 10 9 8 7 6 5 IF_NA_CNTR 0 1 RF_R_CNTR RF_NB_CNTR 1 0 RF_NA_CNTR FRAC_CNTR 1 1 3.0 PROGRAMMABLE REFERENCE DIVIDERS 3.1 IF_R Register If the Control Bits (CTL [1:0]) are 0 0, when LE is transitioned high data is transferred from the 24-bit shift register into a latch which sets the IF PLL 15-bit R counter divide ratio. The divide ratio is programmed using the bits IF_R_CNTR as shown in table 3.1.3. The ratio must be ≥ 3. The IF_CP_WORD [1:0], programs the IF charge pump magnitude and polarity shown in 3.1.4. The OSC bit is used to enable the crystal oscillator mode. FoLD [2:0] is used to set the function of the Lock Detect output (pin 11), according to table 3.1.3. MSB LSB OSC FRAC_16 FoLD [2:0] 23 22 21 19 IF_CP_WORD [1:0] IF_R_CNTR [14:0] 0 0 18 16 1 0 17 2 3.1.1 OSC (IF_R[23]) The OSC bit, IF_R [23], selects whether the oscillator input pins OSCin and OSCx drive the IF and RF R counters separately or by a common input signal path. When the OSC bit = 1, a crystal resonator can be connected between OSCin and OSCx together with 2 capacitors to form a crystal oscillator. When OSC = 0 , the OSCin pin drives the IF R counter while the OSCx drives the RF R counter. 3.1.2 FRAC_16 (IF_R[22]) The FRAC_16 bit, IF_R [22], is used to set the fractional compensation at either 1/16 and 1/15 resolution. When FRAC-16 is set to one, the fractional modulus is set to 1/16 resolution, and FRAC_16 = 0 corresponds to 1/15 (See section 4.2.4). www.national.com 12 (Continued) 3.1.3 15-BIT PROGRAMMABLE REFERENCE DIVIDER RATIO (R COUNTER) (IF_R[2]-[16]) IF_R_CNTR/RF_R_CNTR Divide Ratio 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 3 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 4 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 - - - - - - - - - - - - - - - - 32,767 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Notes: Divide ratio: 3 to 32,767 (Divide ratios less than 3 are prohibited). RF_R_CNTR/IF_R_CNTR These bits select the divide ratio of the programmable reference dividers. 3.1.4 IF_CP_WORD (IF_R[17]-[18]) IF_CP_WORD (IF_R [17] - [18] ) CP_GAIN_8 IF_PD_POL BIT LOCATION FUNCTION 0 1 CP_GAIN_8 IF_R [18] IF Charge Pump Current Gain 1X 8X IF_PD_POL IF_R [17] IF Phase Detector Polarity Negative Positive CP_GAIN_8 is used to toggle the IF charge pump current magnitude between 1x mode (100 uA typ) and 8x mode (800uA typ). IF_PD_POL is set to one when IF VCO characteristics are positive. When IF VCO frequency decreases with increasing control voltage IF_PD_POL should set to zero. 3.1.5 FoLD* Programming Truth Table (IF_R[19]-[21]) FoLD Fo/LD OUTPUT STATE 000 IF and RF Analog Lock Detect (Open Drain) 100 IF Digital Lock Detect 010 RF Digital Lock Detect 110 IF and RF Digital Lock Detect 001 IF R counter 101 IF N counter 011 RF R counter 111 RF N counter *FoLD - Fout/Lock Detect PROGRAMMING BITS 3.2 RF_R Register If the Control Bits (CTL [1:0]) are 1 0, data is transferred from the 24-bit shift register into the RF_R register latch which sets the RF PLL 15-bit R counter divide ratio. The divide ratio is programmed using the RF_R_CNTR word as shown in table 3.1.3. The divide ratio must be ≥ 3. The bits used to control the voltage doubler (V2_EN) and RF Charge Pump (RF_CP_WORD) are detailed in 3.2.2. MSB DLL_MODE 23 LSB V2_EN 22 RF_CP_WORD [4:0] 21 RF_R_CNTR [14:0] 17 13 16 2 1 0 1 0 www.national.com LMX2350/LMX2352 Programming Description LMX2350/LMX2352 Programming Description (Continued) 3.2.1 (RF_R [22 - 23] ) DLL_MODE V2_EN BIT LOCATION FUNCTION 0 1 DLL_MODE RF_R [23] Delay Line Loop Calibration Mode Slow Fast V2_EN RF_R [22] RF_Voltage Doubler Enable Disabled Enabled 1. V2_EN bit when set high enables the voltage doubler for the RF Charge Pump supply. 2. DLL_MODE bit should be set to one for normal usage. 3.2.2 RF_CP_WORD (RF_R[17]-[21]) CP_8X CP_4X CP_2X CP_1X RF_PD_POL RF_PD_POL ( RF_R[17] ) should be set to one when RF VCO characteristics are positive. When RF VCO frequency decreases with increasing control voltage RF_PD_POL should be set to zero. CP_1x, CP_2x, CP_4x, and CP_8x are used to step the RF Charge Pump output current magnitude from 100 uA to 1.6 mA in 100uA steps as shown in the table below. RF Charge Pump Output Truth Table ICPo uA (typ) CP8x CP4x CP2x CP1x RF_R[21] RF_R[20] RF_R[19] RF_R[18] 100 0 0 0 0 200 0 0 0 1 300 0 0 1 0 400 0 0 1 1 - - - - - 900 1 0 0 0 - - - - - 1600 1 1 1 1 4.0 PROGRAMMABLE DIVIDERS (N COUNTERS) 4.1 IF_N Register If the Control Bits (CTL [1:0]) are 01, data is transferred from the 24-bit shift register into the IF_N register latch which sets the PLL 15 bit programmable N counter value and various control functions. The IF_N counter consists of the 3-bit swallow counter (A counter), and the 12 bit programmable counter (B counter). Serial data format is shown below in tables 4.1.2 and 4.1.3. The divide ratio (IF_NB_CNTR) must be ≥3. The divide ratio is programmed using the bits IF_N_CNTR as shown in tables 4.1.2 and 4.1.3. The divide ratio must be ≥56. The CMOS [3:0] bits program the 2 CMOS outputs detailed in section 4.4. MSB LSB IF_CTL_WORD [2:0] 23 CMOS [3:0] 21 4.1.1 IF_CTL_WORD 20 IF_NB_CNTR [11:0] 17 16 4 2 (IF_R[21]-[23]) MSB IF_CNT_RST LSB PWDN_IF Note: See section 4.2.1.2 for IF control word truth table. www.national.com IF_NA_CNTR [2:0] 5 14 PWDN_MODE 0 1 1 0 LMX2350/LMX2352 Programming Description (Continued) 4.1.2 3-BIT IF SWALLOW COUNTER DIVIDE RATIO (IF A COUNTER) Swallow Count (IF_N[2]−[4]) IF_NA_CNTR (A) 2 1 0 0 0 0 0 1 0 0 1 - - - - 7 1 1 1 Note: Swallow Counter Value: 0 to 7 IF_NB_CNTR ≥ IF_NA_CNTR Minimum continuous count = 56 ( A=0, B=7) 4.1.3 12-BIT IF PROGRAMMABLE COUNTER DIVIDE RATIO (IF B COUNTER) (IF_N[5]-[16]) IF_NB_CNTR Divide Ratio 11 10 9 8 7 6 5 4 3 2 1 0 3 0 0 0 0 0 0 0 0 0 0 1 1 4 0 0 0 0 0 0 0 0 0 1 0 0 - - - - - - - - - - - - - 4,095 1 1 1 1 1 1 1 1 1 1 1 1 Note: Divide ratio: 3 to 4095 (Divide ratios less than 3 are prohibited) IF_NB_CNTR ≥ IF_NA_CNTR N divider continuous integer divide ratio 56 to 32,767. 4.2 RF_N Register If the control bits (CTL[2:0]) are 11, data is transferred from the 24-bit shift register into the RF_N register latch which sets the RF PLL 19 bit programmable N counter register and various control functions. The RF N counter consists of the 5-bit swallow counter (A counter) the 10 bit programmable counter (B counter), and 4 bit fractional counter. Serial data format is shown below. The divide ratio (RF_NB_CNTR) must be ≥3, and must be ≥ the swallow counter value + 2; RF_NB_CNTR≥ ( RF_NA_CNTR+2). MSB LSB RF_CTL_WORD [2:0] 23 RF_NB_CNTR [9:0] 21 4.2.1.1 RF_CTL_WORD 20 RF_NA_CNTR [4:0] 11 FRAC_CONT [3:0] 10 6 5 2 1 1 1 0 (RF_N[21]-[23]) MSB LSB RF_CNT_RST PWDN_RF PRESC_SEL 4.2.1.2 RF/IF Control Word Truth Table BIT FUNCTION 0 1 IF_CNT_RST/RF_CNT_RST IF/RF counter reset Normal Operation Reset PWDN_IF/PWDN_RF IF/RF power down Powered up Powered down PWDN_MODE PRESC LMX2350 Power down mode select Asynchronous power down Synchronous power down Prescaler Modulus select 16/17 (0.5 to 1.2 GHz operation) 32/33 (1.2 to 2.5 GHz operation) 8/9 (0.25 to 0.5 GHz operation) 16/17 (0.5 to 1.2 GHz operation) LMX2352 pump and phase comparator logic to a TRI-STATE condition. The MICROWIRE control register remains active and capable of loading and latching in data during all of the power down modes. Both synchronous and asynchronous power down modes are available with the LMX2350 family in order to adapt to different types of applications. The power down mode bit IF_N[21] is used to select between synchronous and asynchronous power down. The MICROWIRE control register remains active and capable of loading and latching in data during all of the power down modes. The Counter Reset enable bit when activated allows the reset of both N and R counters. Upon powering up, the N counter resumes counting in ’close’ alignment with the R counter (the maximum error is one prescaler cycle). Activation of the PLL power down bits result in the disabling of the respective N counter divider and de-biasing of its respective fin inputs (to a high impedance state). The respective R counter functionality also becomes disabled when the power down bit is activated. The OSCin pin reverts to a high impedance state when both RF and IF power down bits are asserted. Power down forces the respective charge 15 www.national.com LMX2350/LMX2352 Programming Description 4.2.2 5-BIT RF SWALLOW COUNTER DIVIDE RATIO (RF A COUNTER) (RF_N[6]-[10]) (Continued) Synchronous Power down Mode Swallow Count One of the PLL loops can be synchronously powered down by first setting the power down mode bit HIGH (IF_N[21] = 1) and then asserting its power down bit (IF_N[22] or RF_N[22] = 1). The power down function is gated by the charge pump. Once the power down bit is loaded, the part will go into power down mode upon the completion of a charge pump pulse event. Asynchronous Power down Mode One of the PLL loops can be asynchronously powered down by first setting the power down mode bit LOW (IF_N[21] = 0) and then asserting its power down bit (IF_N[22] or RF_N[22] = 1). The power down function is NOT gated by the charge pump. Once the power down bit is loaded, the part will go into power down mode immediately. Prescaler select is used to set the RF prescaler. The LMX2350 is capable of operating from 500 MHz to 1.2 GHz with the 16/17 prescaler, and 1.2 GHz to 2.5 GHz with the 32/33 prescaler selection. The LMX2352 is capable of operating from 250 MHz to 500 MHz with the 8/9 prescaler, and 500MHz to 1.2GHz with 16/17 prescaler selection. RF_NA_CNTR (A) 4 3 2 1 0 0 0 0 0 0 0 1 0 0 0 0 1 - - - - - - 31 1 1 1 1 1 Note: Swallow Counter Value LMX2350: 0 to 31; LMX2352: 0 to 15 RF_NB_CNTR ≥ RF_NA_CNTR + 2 4.2.3 10-BIT RF PROGRAMMABLE COUNTER DIVIDE RATIO (RF B COUNTER) (RF_N[11]-[20]) RF_NB_CNTR Divide Ratio 9 8 7 6 5 4 3 2 1 0 3 0 0 0 0 0 0 0 0 1 1 4 0 0 0 0 0 0 0 1 0 0 - - - - - - - - - - - 1,023 1 1 1 1 1 1 1 1 1 1 Note: Divide ratio: 3 to 1023 (Divide ratios less than 3 are prohibited) RF_NB_CNTR ≥ RF_NA_CNTR + 2 4.2.4 FRACTIONAL MODULUS ACCUMULATOR (FRAC_CNTR) (RF_N[2]-[5]) Fractional Ratio (F) FRAC_CNTR Modulus 15 Modulus 16 RF_N[5] RF_N[4] RF_N[3] RF_N[2] 0 0 0 0 0 0 1/15 1/16 0 0 0 1 2/15 2/16 0 0 1 0 - - - - - - 14/15 14/16 1 1 1 0 N/A 15/16 1 1 1 1 4.3 PULSE SWALLOW FUNCTION fvco = [N + F] x [fosc / R ] N = (P x B) + A fosc: Output frequency of the external reference frequency oscillator R: Preset divide ratio of binary 15-bit programmable reference counter (3 to 16383) P: Preset modulus of dual modulus prescaler (LMX2350:RF P=16 or 32, IF P=8) (LMX2352:RF P=8 or 16, IF P=8) F: Fractional ratio (contents of FRAC_CNTR divided by the fractional modulus) fvco: Output frequency of external voltage controlled oscillator (VCO) B: Preset divide ratio of binary 10-bit programmable counter A: Preset value of binary 4 or 5-bit swallow counter (0 ≤ A ≤ 31 {RF} , 0 ≤ A ≤ 15 {IF} , A+2 ≤ B {RF}, A ≤ B {IF}) 4.4 CMOS (Programmable CMOS outputs) (IF_N[17]-[20]) MSB FastLock LSB TEST OUT_1 Note: Test bit is reserved and should be set to zero for normal usage. www.national.com 16 OUT_0 (Continued) 4.4.1 Programmable CMOS Output Truth Table BIT LOCATION FUNCTION 0 1 OUT_0 IF_N[17] OUT0 CMOS output pin level set LOW HIGH OUT_1 IF_N[18] OUT1 CMOS output pin level set LOW HIGH FastLock IF_N[20] FastLock mode select CMOS output FastLock mode When the FastLock bit is set to one, OUT_0 and OUT_1 are don’t care bits. FastLock mode utilizes the OUT0 and OUT1 output pins to synchronously switch between active low and TRI-STATE. The OUT0 = LOW state occurs whenever the RF loop’s CP_8X is selected HIGH while the FastLock bit is set HIGH (see programming description 3.2.2). The OUT0 pin reverts to TRI-STATE when the CP_8X bit is LOW. Similarly for the IF loop, the synchronous activation of OUT1= LOW or TRI-STATE, is dependent on whether the CP_GAIN_8 is high or low respectively (see programming description 3.1.4). 4.5 SERIAL DATA INPUT TIMING DS100831-3 Note: Data shifted into register on clock rising edge. Data is shifted in MSB first. TEST CONDITIONS: The Serial Data Input Timing is tested using a symmetrical waveform around Vcc/2. The test waveform has an edge rate of 0.6 V/nsec with amplitudes of 2.2V @ Vcc=2.7 V and 2.6V @ Vcc = 5.5 V. 17 www.national.com LMX2350/LMX2352 Programming Description LMX2350/LMX2352 Programming Description (Continued) 4.6 LOCK DETECT DIGITAL FILTER The Lock Detect Digital Filter compares the difference between the phase of the inputs of the phase detector to a RC generated delay of approximately 15nS. To enter the locked state (Lock = HIGH) the phase error must be less than the 15nS RC delay for 5 consecutive reference cycles. Once in lock (Lock = HIGH), the RC delay is changed to approximately 30nS. To exit the locked state (Lock = LOW), the phase error must become greater than the 30nS RC delay. When the PLL is in the power down mode, Lock is forced LOW. A flow chart of the digital filter is shown at right. DS100831-4 www.national.com 18 (Continued) 4.7 ANALOG LOCK DETECT FILTER When the Fo/LD output is configured in analog lock detect mode an external lock detect circuit is needed in order to provide a steady LOW signal when the PLL is in the locked state. A typical circuit is shown below. The fold output is active low (open drain) only when analog lock detect mode is selected. DS100831-5 4.8 TYPICAL LOCK DETECT TIMING DS100831-6 19 www.national.com LMX2350/LMX2352 Programming Description LMX2350/LMX2352 Physical Dimensions inches (millimeters) unless otherwise noted Molded TSSOP, JEDEC Plastic Package (MTC24) Order Number LMX2350TM or LMX2352TM NS Package MTC24 www.national.com 20 inches (millimeters) unless otherwise noted (Continued) Molded CSP, JEDEC Plastic Package (SLB24A) Order Number LMX2350SLB or LMX2352SLB NS Package SLB24A LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Corporation Americas Email: support@nsc.com www.national.com National Semiconductor Europe Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Français Tel: +33 (0) 1 41 91 8790 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Asia Pacific Customer Response Group Tel: 65-2544466 Fax: 65-2504466 Email: ap.support@nsc.com National Semiconductor Japan Ltd. Tel: 81-3-5639-7560 Fax: 81-3-5639-7507 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. LMX2350/LMX2352 PLLatinum Fractional N RF / Integer N IF Dual Low Power Frequency Synthesizer Physical Dimensions IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP® Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2011, Texas Instruments Incorporated