SN74AXC8T245-Q1
SCES892C – NOVEMBER 2018 – REVISED OCTOBER 2021
SN74AXC8T245-Q1 Automotive 8-Bit Dual-Supply Bus Transceiver With Configurable
Voltage Translation and Tri-State Outputs
1 Features
•
•
•
•
•
•
•
•
•
•
AEC-Q100 qualified for automotive applications
Available in wettable flank QFN (WRGY) package
Qualified fully configurable dual-rail design allows
each port to operate with a power supply range
from 0.65 V to 3.6 V
Operating temperature from –40°C to +125°C
Multiple direction-control pins to allow
simultaneous up and down translation
Up to 380 Mbps support when translating from 1.8
V to 3.3 V
VCC isolation feature to effectively Isolate both
bses in a power-down scenario
Partial power-down mode to limit backflow current
in a power-down scenario
Compatible with SN74AVC8T245-Q1 level shifter
Latch-up performance exceeds 100 mA per JESD
78, class II
2 Applications
•
•
•
•
Infotainment head unit
ADAS fusion
ADAS front camera
HEV battery management system
The SN74AXC8T245-Q1 device is designed for
asynchronous communication between data buses.
The device transmits data from the A bus to the B bus
or from the B bus to the A bus, depending on the logic
level of the direction-control inputs (DIR1 and DIR2).
The output-enable (OE) input is used to disable the
outputs so the buses are effectively isolated.
The SN74AXC8T245-Q1 device is designed so the
control pins (DIR and OE) are referenced to VCCA.
This device is fully specified for partial-power-down
applications using Ioff. The Ioff circuitry disables
the outputs when the device is powered down.
This inhibits current backflow into the device which
prevents damage to the device.
The VCC isolation feature ensures that if either VCC
input supply is below 100 mV, all level shifter outputs
are disabled and placed into a high-impedance state.
To ensure the high-impedance state of the level shifter
I/Os during power up or power down, OE should be
tied to VCCA through a pullup resistor; the minimum
value of the resistor is determined by the currentsinking capability of the driver.
Device Information
3 Description
The SN74AXC8T245-Q1 AEC-Q100 qualified device
is an 8-bit non-inverting bus transceiver that resolves
voltage level mismatch between devices operating at
the latest voltage nodes (0.7 V, 0.8 V, and 0.9 V) and
devices operating at industry standard voltage nodes
(1.8 V, 2.5 V, and 3.3 V) and vice versa.
The device operates by using two independent powersupply rails (VCCA and VCCB) that operate as low as
0.65 V. Data pins A1 through A8 are designed to track
VCCA, which accepts any supply voltage from 0.65 V
to 3.6 V. Data pins B1 through B8 are designed to
track VCCB, which accepts any supply voltage from
0.65 V to 3.6 V.
PART NUMBER(1)
PACKAGE
BODY SIZE (NOM)
SN74AXC8T245PW-Q1
TSSOP (24)
4.40 mm × 7.80 mm
SN74AXC8T245RHL-Q1
VQFN (24)
3.50 mm × 5.50 mm
SN74AXC8T245WRGY-Q1
VQFN (24)
3.50 mm × 5.50 mm
(1)
For all available packages, see the orderable addendum at
the end of the data sheet.
3.3 V
1.5 V
Processor
Control Block
VCCA DIR1 DIR2
VCCB
A1
B1
A2
B2
B3
A3
Data Block
Interrupts
A4
SN74AXC8T245-Q1
B4
A5
B5
A6
B6
Register Map
B7
A7
A8
Power Management
GND
B8
Sensor Block
GND
Typical Application Schematic
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
SN74AXC8T245-Q1
www.ti.com
SCES892C – NOVEMBER 2018 – REVISED OCTOBER 2021
Table of Contents
1 Features............................................................................1
2 Applications..................................................................... 1
3 Description.......................................................................1
4 Revision History.............................................................. 2
5 Pin Configuration and Functions...................................3
6 Specifications.................................................................. 4
6.1 Absolute Maximum Ratings........................................ 4
6.2 ESD Ratings............................................................... 4
6.3 Recommended Operating Conditions.........................5
6.4 Thermal Information....................................................5
6.5 Electrical Characteristics.............................................6
6.6 Switching Characteristics, VCCA = 0.7 V..................... 7
6.7 Switching Characteristics, VCCA = 0.8 V..................... 8
6.8 Switching Characteristics, VCCA = 0.9 V..................... 9
6.9 Switching Characteristics, VCCA = 1.2 V................... 10
6.10 Switching Characteristics, VCCA = 1.5 V................. 11
6.11 Switching Characteristics, VCCA = 1.8 V................. 12
6.12 Switching Characteristics, VCCA = 2.5 V................. 13
6.13 Switching Characteristics, VCCA = 3.3 V................. 14
6.14 Operating Characteristics: TA = 25°C..................... 15
6.15 Typical Characteristics............................................ 17
7 Parameter Measurement Information.......................... 18
8 Detailed Description......................................................20
8.1 Overview................................................................... 20
8.2 Functional Block Diagram......................................... 20
8.3 Feature Description...................................................21
8.4 Device Functional Modes..........................................22
9 Application and Implementation.................................. 23
9.1 Application Information............................................. 23
9.2 Typical Application.................................................... 23
10 Power Supply Recommendations..............................25
11 Layout........................................................................... 25
11.1 Layout Guidelines................................................... 25
11.2 Layout Example...................................................... 25
12 Device and Documentation Support..........................26
12.1 Documentation Support.......................................... 26
12.2 Receiving Notification of Documentation Updates..26
12.3 Support Resources................................................. 26
12.4 Trademarks............................................................. 26
12.5 Electrostatic Discharge Caution..............................26
13 Mechanical, Packaging, and Orderable
Information.................................................................... 26
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision B (May 2021) to Revision C (October 2021)
Page
• Reformatted the Device Information table ......................................................................................................... 1
• Added wettable flank information in Features ....................................................................................................1
• Added wettable flank information in Feature Description ................................................................................ 21
Changes from Revision A (July 2019) to Revision B (May 2021)
Page
• Added the SN74AXC8T245QRGYQ1 part number to the Device Information table.......................................... 1
• Updated the numbering format for tables, figures, and cross-references throughout the document..................1
• Added the RGY Package to the Pin Configuration and Functions section......................................................... 3
• Added the RGY Package to the Thermal Information section............................................................................ 5
Changes from Revision * (November 2018) to Revision A (July 2019)
Page
• Changed status to production data.....................................................................................................................1
• Added Typical Characteristics graphs for Production Data release. ................................................................17
2
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: SN74AXC8T245-Q1
SN74AXC8T245-Q1
www.ti.com
SCES892C – NOVEMBER 2018 – REVISED OCTOBER 2021
VCCB
24
VCCB
OE
21 B1
20 B2
19 B3
18 B4
17 B5
16 B6
15 B7
14 B8
2
23
3
22
4
5
6
PAD
7
8
9
10
13
11
GND
DIR1
A1
A2
A3
A4
A5
A6
A7
A8
DIR2
VCCA
VCCB
VCCB
OE
B1
B2
B3
B4
B5
B6
B7
B8
GND
GND 12
24
23
22
21
20
19
18
17
16
15
14
13
1
2
3
4
5
6
7
8
9
10
11
12
VCCA
DIR1
A1
A2
A3
A4
A5
A6
A7
A8
DIR2
GND
1
5 Pin Configuration and Functions
PAD — may be grounded (recommended) or left floating.
.
Figure 5-1. PW Package 24-Pin TSSOP Top View
Figure 5-2. RHL and WRGY Package 24-Pin VQFN
Top View
Table 5-1. Pin Functions
PIN
PW, RHL,
WRGY
I/O
A1
3
I/O
Input/output A1. Referenced to VCCA.
A2
4
I/O
Input/output A2. Referenced to VCCA.
A3
5
I/O
Input/output A3. Referenced to VCCA.
A4
6
I/O
Input/output A4. Referenced to VCCA.
A5
7
I/O
Input/output A5. Referenced to VCCA.
A6
8
I/O
Input/output A6. Referenced to VCCA.
A7
9
I/O
Input/output A7. Referenced to VCCA.
A8
10
I/O
Input/output A8. Referenced to VCCA.
B1
21
I/O
Input/output B1. Referenced to VCCB.
B2
20
I/O
Input/output B2. Referenced to VCCB.
B3
19
I/O
Input/output B3. Referenced to VCCB.
B4
18
I/O
Input/output B4. Referenced to VCCB.
B5
17
I/O
Input/output B5. Referenced to VCCB.
B6
16
I/O
Input/output B6. Referenced to VCCB.
B7
15
I/O
Input/output B7. Referenced to VCCB.
B8
14
I/O
Input/output B8. Referenced to VCCB.
DIR1
2
I
Direction-control signal 1. Referenced to VCCA. Refer to Table 8-1.
DIR2
11
I
Direction-control signal 2. Refer to Table 8-1.
Referenced to VCCA. Tie to GND to maintain backward compatibility with SN74AVC8T245Q1 device.
12
—
Ground
13
—
Ground
OE
22
I
VCCA
1
—
A-port supply voltage. 0.65 V ≤ VCCA ≤ 3.6 V
23
—
B-port supply voltage. 0.65 V ≤ VCCB ≤ 3.6 V
24
—
B-port supply voltage. 0.65 V ≤ VCCB ≤ 3.6 V
NAME
GND
VCCB
DESCRIPTION
Output Enable. Pull to GND to enable all outputs. Pull to VCCA to place all outputs in
high-impedance mode. Referenced to VCCA. Refer to Table 8-1.
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: SN74AXC8T245-Q1
3
SN74AXC8T245-Q1
www.ti.com
SCES892C – NOVEMBER 2018 – REVISED OCTOBER 2021
6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted)(1)
Supply voltage, VCCA
Supply voltage, VCCB
MIN
MAX
UNIT
–0.5
4.2
V
V
–0.5
4.2
I/O ports (A port)
–0.5
4.2
I/O ports (B port)
–0.5
4.2
Control inputs
–0.5
4.2
A port
–0.5
4.2
B port
–0.5
4.2
A port
–0.5
VCCA + 0.2
B port
–0.5
VCCB + 0.2
Input clamp current, IIK
VI < 0
–50
Output clamp current, IOK
VO < 0
–50
Input voltage, VI (2)
Voltage applied to any output
in the high-impedance or power-off state, VO (2)
Voltage applied to any output in the high or low state, VO (2) (3)
V
V
V
mA
mA
Continuous output current, IO
–50
50
mA
Continuous current through VCCA, VCCB, or GND
–100
100
mA
150
°C
150
°C
Junction Temperature, TJ
Storage temperature, Tstg
(1)
(2)
(3)
–65
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Section 6.3.
Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
The input voltage and output negative-voltage ratings may be exceeded if the input and output current ratings are observed.
The output positive-voltage rating may be exceeded up to 4.2 V maximum if the output current rating is observed.
6.2 ESD Ratings
VALUE
V(ESD)
(1)
4
Electrostatic discharge
Human-body model (HBM), per AEC Q100-002(1)
±8000
Charged-device model (CDM), per AEC Q100-011
±1000
UNIT
V
AEC Q100-002 indicates that HBM stressing shall be in accordance with the ANSI/ESDA/JEDEC JS-001 specification
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: SN74AXC8T245-Q1
SN74AXC8T245-Q1
www.ti.com
SCES892C – NOVEMBER 2018 – REVISED OCTOBER 2021
6.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted) (1) (2) (3)
MIN
MAX
UNIT
VCCA
Supply voltage
0.65
3.6
V
VCCB
Supply voltage
0.65
3.6
V
Data inputs
VIH
VCCI = 0.65 V - 0.75 V
VCCI × 0.70
VCCI = 0.76 V - 1 V
VCCI × 0.70
VCCI = 1.1 V - 1.95 V
VCCI × 0.65
VCCI = 2.3 V - 2.7 V
1.6
VCCI = 3 V - 3.6 V
High-level input voltage
Control inputs
(DIR, OE)
Referenced to VCCA
2
VCCA = 0.65 V - 0.75 V
VCCA × 0.70
VCCA = 0.76 V - 1 V
VCCA × 0.70
VCCA = 1.1 V - 1.95 V
VCCA × 0.65
VCCA = 2.3 V - 2.7 V
1.6
VCCA = 3 V - 3.6 V
Data inputs
VIL
Low-level input voltage
Control inputs
(DIR, OE)
Referenced to VCCA
2
VCCI = 0.65 V - 0.75 V
VCCI × 0.30
VCCI = 0.76 V - 1 V
VCCI × 0.30
VCCI = 1.1 V - 1.95 V
VCCI × 0.35
VCCI = 2.3 V - 2.7 V
0.7
VCCI = 3 V - 3.6 V
0.8
VCCA = 0.65 V - 0.75 V
VCCA × 0.30
VCCA = 0.76 V - 1 V
VCCA × 0.30
VCCA = 1.1 V - 1.95 V
VCCA × 0.35
VCCA = 2.3 V - 2.7 V
0.7
VCCA = 3 V - 3.6 V
0
VO
Output voltage
Δt/Δv
Input transition rise or fall rate
TA
Operating free-air temperature
(1)
(2)
(3)
V
0.8
Input voltage(3)
VI
V
3.6
V
(2)
Active state
0
VCCO
Tri-state
0
3.6
10
ns/V
–40
125
°C
V
VCCI is the VCC associated with the input port.
VCCO is the VCC associated with the output port.
All unused data inputs of the device must be held at VCCI or GND to ensure proper device operation. See the Implications of Slow or
Floating CMOS Inputs application report.
6.4 Thermal Information
SN74AXC8T245-Q1
THERMAL METRIC(1)
PW (TSSOP)
RHL (VQFN)
WRGY (VQFN)
UNIT
24 PINS
24 PINS
24 PINS
RθJA
Junction-to-ambient thermal resistance
92.0
35.0
48.1
°C/W
RθJC(top)
Junction-to-case (top) thermal resistance
29.3
39.9
43.2
°C/W
RθJB
Junction-to-board thermal resistance
46.7
13.8
26.1
°C/W
ψJT
Junction-to-top characterization parameter
1.5
0.3
2.9
°C/W
ψJB
Junction-to-board characterization parameter
46.2
13.8
26.0
°C/W
RθJC(bot)
Junction-to-case (bottom) thermal resistance
N/A
1.4
15.8
°C/W
(1)
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report.
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: SN74AXC8T245-Q1
5
SN74AXC8T245-Q1
www.ti.com
SCES892C – NOVEMBER 2018 – REVISED OCTOBER 2021
6.5 Electrical Characteristics
Over recommended operating free-air temperature range (unless otherwise noted)(1) (2)
PARAMETER
VOH
VOL
Low-level
output
voltage
VI = VIH
VI = VIL
ICCB
VCCA supply
current
VCCB supply
current
MIN
TYP(4)
–40°C to 125°C
MAX
MIN
TYP(4)
MAX
0.7 V - 3.6 V
VCCO – 0.1
VCCO – 0.1
0.65 V
0.65 V
0.55
0.55
IOH = –200 µA
0.76 V
0.76 V
0.58
0.58
IOH = –500 µA
0.85 V
0.85 V
0.65
0.65
IOH = -3 mA
1.1 V
1.1 V
0.85
0.85
IOH = -6 mA
1.4 V
1.4 V
1.05
1.05
IOH = -8 mA
1.65 V
1.65 V
1.2
1.2
IOH = -9 mA
2.3 V
2.3 V
1.75
1.75
IOH = -12 mA
3V
3V
2.3
IOL = 100 µA
0.7 V - 3.6 V
0.7 V - 3.6 V
0.1
IOL = 50 µA
0.65 V
0.65 V
0.1
0.1
IOL = 200 µA
0.76 V
0.76 V
0.18
0.18
IOL = 500 µA
0.85 V
0.85 V
0.2
0.2
IOL = 3 mA
1.1 V
1.1 V
0.25
0.25
IOL = 6 mA
1.4 V
1.4 V
0.35
0.35
IOL = 8 mA
1.65 V
1.65 V
0.45
0.45
IOL = 9 mA
2.3 V
2.3 V
0.55
0.55
IOL = 12 mA
3V
3V
0.7
0.7
0.65 V - 3.6 V
0.65 V - 3.6 V
0V
Ioff
ICCA
–40°C to 85°C
0.7 V - 3.6 V
A Port:
Partial power VI or VO = 0 V - 3.6 V
down current B Port:
VI or VO = 0 V - 3.6 V
(3)
VCCB
IOH = –100 µA
Input leakage Control Inputs (DIR, OE):
current
VI = VCCA or GND
Highimpedance
state output
current
VCCA
IOH = –50 µA
II
IOZ
V
2.3
0.1
-0.5
0.5
-1
1
0 V - 3.6 V
-8
8
-12
12
0 V - 3.6 V
0V
-8
8
-12
12
A Port:
VO = VCCO or GND, VI = VCCI
or GND, OE = VIH
3.6 V
3.6 V
-8
8
-12
12
B Port:
VO = VCCO or GND, VI = VCCI
or GND, OE = VIH
3.6 V
3.6 V
0.65 V - 3.6 V
0.65 V - 3.6 V
0V
3.6 V
VI = VCCI or GND, IO = 0 mA
VI = VCCI or GND, IO = 0 mA
UNIT
V
µA
µA
µA
-8
8
-12
12
20
-2
40
-12
µA
3.6 V
0V
12
25
0.65 V - 3.6 V
0.65 V - 3.6 V
20
40
0V
3.6 V
12
3.6 V
0V
0.65 V - 3.6 V
0.65 V - 3.6 V
-2
25
µA
60
µA
-12
ICCA
+
ICCB
Combined
supply
current
VI = VCCI or GND, IO = 0 mA
Ci
Input
capacitance
Control Inputs (DIR, OE):
VI = 3.3 V or GND
3.3 V
3.3 V
4.5
4.5
pF
Cio
Data I/O
capacitance
Ports A and B:
OE = VCCA, VO = 1.65V DC +
1 MHz -16 dBm sine wave
3.3 V
3.3 V
5.7
5.7
pF
(1)
(2)
(3)
(4)
6
High-level
output
voltage
TEST CONDITIONS
30
VCCO is the VCC associated with the output port.
VCCI is the VCC associated with the input port.
For I/O ports, the parameter IOZ includes the input leakage current.
All typical values are for TA = 25°C
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: SN74AXC8T245-Q1
SN74AXC8T245-Q1
www.ti.com
SCES892C – NOVEMBER 2018 – REVISED OCTOBER 2021
6.6 Switching Characteristics, VCCA = 0.7 V
See Figure 7-1 and Figure 7-2 for test circuit and loading conditions. See Figure 7-3 and Figure 7-4 for measurement
waveforms.
B-PORT SUPPLY VOLTAGE (VCCB)
PARAMETER
tpd
tdis
ten
Propagation
delay
TEST CONDITIONS
0.7 V ± 0.05 V
0.9 V ± 0.045 V
1.2 V ± 0.1 V
MIN
MAX
MIN
0.8 V ± 0.04 V
MAX
MIN
MAX
MIN
MAX
From input A
to output B
–40°C to 85°C
0.5
172
0.5
114
0.5
82
0.5
49
–40°C to 125°C
0.5
172
0.5
114
0.5
82
0.5
49
From input B
to output A
–40°C to 85°C
0.5
172
0.5
153
0.5
126
0.5
88
–40°C to 125°C
0.5
172
0.5
153
0.5
126
0.5
88
From input OE
to output A
–40°C to 85°C
0.5
192
0.5
192
0.5
192
0.5
192
–40°C to 125°C
0.5
195
0.5
195
0.5
195
0.5
195
From input OE
to output B
–40°C to 85°C
0.5
156
0.5
129
0.5
118
0.5
120
–40°C to 125°C
0.5
157
0.5
129
0.5
120
0.5
122
From input OE
to output A
–40°C to 85°C
0.5
237
0.5
237
0.5
237
0.5
237
–40°C to 125°C
0.5
237
0.5
237
0.5
237
0.5
237
From input OE
to output B
–40°C to 85°C
0.5
223
0.5
145
0.5
106
0.5
74
–40°C to 125°C
0.5
223
0.5
145
0.5
106
0.5
74
Disable time
Enable time
UNIT
ns
ns
ns
B-PORT SUPPLY VOLTAGE (VCCB)
PARAMETER
tpd
tdis
ten
Propagation
delay
TEST CONDITIONS
1.5 V ± 0.1 V
1.8 V ± 0.15 V
2.5 V ± 0.2 V
3.3 V ± 0.3 V
MIN
MAX
MIN
MAX
MIN
MAX
MIN
MAX
From input A
to output B
–40°C to 85°C
0.5
46
0.5
49
0.5
61
0.5
142
–40°C to 125°C
0.5
46
0.5
49
0.5
61
0.5
142
From input B
to output A
–40°C to 85°C
0.5
83
0.5
82
0.5
81
0.5
81
–40°C to 125°C
0.5
83
0.5
82
0.5
81
0.5
81
From input OE
to output A
–40°C to 85°C
0.5
192
0.5
192
0.5
192
0.5
192
–40°C to 125°C
0.5
195
0.5
195
0.5
195
0.5
195
From input OE
to output B
–40°C to 85°C
0.5
69
0.5
66
0.5
67
0.5
150
–40°C to 125°C
0.5
70
0.5
67
0.5
67
0.5
150
From input OE
to output A
–40°C to 85°C
0.5
237
0.5
237
0.5
237
0.5
237
–40°C to 125°C
0.5
237
0.5
237
0.5
237
0.5
237
From input OE
to output B
–40°C to 85°C
0.5
68
0.5
69
0.5
84
0.5
552
–40°C to 125°C
0.5
68
0.5
69
0.5
84
0.5
552
Disable time
Enable time
UNIT
ns
ns
ns
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: SN74AXC8T245-Q1
7
SN74AXC8T245-Q1
www.ti.com
SCES892C – NOVEMBER 2018 – REVISED OCTOBER 2021
6.7 Switching Characteristics, VCCA = 0.8 V
See Figure 7-1 and Figure 7-2 for test circuit and loading conditions. See Figure 7-3 and Figure 7-4 for measurement
waveforms.
B-PORT SUPPLY VOLTAGE (VCCB)
PARAMETER
tpd
tdis
ten
Propagation
delay
TEST CONDITIONS
0.7 V ± 0.05 V
0.8 V ± 0.04 V
0.9 V ± 0.045 V
1.2 V ± 0.1 V
MIN
MAX
MIN
MAX
MIN
MAX
MIN
MAX
From input A
to output B
–40°C to 85°C
0.5
153
0.5
95
0.5
62
0.5
32
–40°C to 125°C
0.5
153
0.5
95
0.5
62
0.5
32
From input B
to output A
–40°C to 85°C
0.5
114
0.5
95
0.5
78
0.5
52
–40°C to 125°C
0.5
114
0.5
95
0.5
78
0.5
52
From input OE
to output A
–40°C to 85°C
0.5
101
0.5
101
0.5
101
0.5
101
–40°C to 125°C
0.5
103
0.5
103
0.5
103
0.5
103
From input OE
to output B
–40°C to 85°C
0.5
141
0.5
114
0.5
104
0.5
106
–40°C to 125°C
0.5
142
0.5
115
0.5
106
0.5
109
From input OE
to output A
–40°C to 85°C
0.5
102
0.5
102
0.5
102
0.5
102
–40°C to 125°C
0.5
102
0.5
102
0.5
102
0.5
102
From input OE
to output B
–40°C to 85°C
0.5
202
0.5
124
0.5
86
0.5
52
–40°C to 125°C
0.5
202
0.5
124
0.5
86
0.5
52
Disable time
Enable time
UNIT
ns
ns
ns
B-PORT SUPPLY VOLTAGE (VCCB)
PARAMETER
tpd
tdis
ten
8
Propagation
delay
TEST CONDITIONS
1.5 V ± 0.1 V
1.8 V ± 0.15 V
2.5 V ± 0.2 V
3.3 V ± 0.3 V
MIN
MAX
MIN
MAX
MIN
MAX
MIN
MAX
From input A
to output B
–40°C to 85°C
0.5
26
0.5
25
0.5
25
0.5
35
–40°C to 125°C
0.5
26
0.5
25
0.5
25
0.5
35
From input B
to output A
–40°C to 85°C
0.5
42
0.5
41
0.5
40
0.5
40
–40°C to 125°C
0.5
42
0.5
41
0.5
40
0.5
40
From input OE
to output A
–40°C to 85°C
0.5
101
0.5
101
0.5
101
0.5
101
–40°C to 125°C
0.5
103
0.5
103
0.5
103
0.5
103
From input OE
to output B
–40°C to 85°C
0.5
55
0.5
51
0.5
49
0.5
51
–40°C to 125°C
0.5
57
0.5
53
0.5
50
0.5
52
From input OE
to output A
–40°C to 85°C
0.5
102
0.5
102
0.5
102
0.5
102
–40°C to 125°C
0.5
102
0.5
102
0.5
102
0.5
102
From input OE
to output B
–40°C to 85°C
0.5
44
0.5
43
0.5
45
0.5
58
–40°C to 125°C
0.5
44
0.5
43
0.5
45
0.5
58
Disable time
Enable time
Submit Document Feedback
UNIT
ns
ns
ns
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: SN74AXC8T245-Q1
SN74AXC8T245-Q1
www.ti.com
SCES892C – NOVEMBER 2018 – REVISED OCTOBER 2021
6.8 Switching Characteristics, VCCA = 0.9 V
See Figure 7-1 and Figure 7-2 for test circuit and loading conditions. See Figure 7-3 and Figure 7-4 for measurement
waveforms.
B-PORT SUPPLY VOLTAGE (VCCB)
PARAMETER
tpd
tdis
ten
Propagation
delay
TEST CONDITIONS
0.7 V ± 0.05 V
0.8 V ± 0.04 V
0.9 V ± 0.045 V
MIN
MAX
MIN
MAX
MIN
MAX
MIN
1.2 V ± 0.1 V
MAX
From input A
to output B
–40°C to 85°C
0.5
127
0.5
78
0.5
52
0.5
23
–40°C to 125°C
0.5
127
0.5
78
0.5
52
0.5
23
From input B
to output A
–40°C to 85°C
0.5
82
0.5
63
0.5
52
0.5
39
–40°C to 125°C
0.5
82
0.5
63
0.5
52
0.5
39
From input OE
to output A
–40°C to 85°C
0.5
125
0.5
125
0.5
125
0.5
125
–40°C to 125°C
0.5
128
0.5
128
0.5
128
0.5
128
From input OE
to output B
–40°C to 85°C
0.5
131
0.5
105
0.5
96
0.5
99
–40°C to 125°C
0.5
133
0.5
107
0.5
98
0.5
101
From input OE
to output A
–40°C to 85°C
0.5
124
0.5
124
0.5
124
0.5
124
–40°C to 125°C
0.5
128
0.5
128
0.5
128
0.5
128
From input OE
to output B
–40°C to 85°C
0.5
191
0.5
113
0.5
75
0.5
41
–40°C to 125°C
0.5
191
0.5
113
0.5
75
0.5
41
Disable time
Enable time
UNIT
ns
ns
ns
B-PORT SUPPLY VOLTAGE (VCCB)
PARAMETER
TEST CONDITIONS
1.5 V ± 0.1 V
MIN
tpd
tdis
ten
Propagation
delay
1.8 V ± 0.15 V
2.5 V ± 0.2 V
3.3 V ± 0.3 V
MAX
MIN
MAX
MIN
MAX
MIN
MAX
–40°C to 85°C
0.5
17
0.5
15
0.5
14
0.5
17
–40°C to 125°C
0.5
17
0.5
15
0.5
14
0.5
17
From input B
to output A
–40°C to 85°C
0.5
28
0.5
24
0.5
22
0.5
22
–40°C to 125°C
0.5
28
0.5
24
0.5
22
0.5
22
From input OE
to output A
–40°C to 85°C
0.5
125
0.5
125
0.5
125
0.5
125
–40°C to 125°C
0.5
128
0.5
128
0.5
128
0.5
128
From input OE
to output B
–40°C to 85°C
0.5
47
0.5
44
0.5
40
0.5
73
–40°C to 125°C
0.5
50
0.5
46
0.5
42
0.5
73
From input OE
to output A
–40°C to 85°C
0.5
124
0.5
124
0.5
124
0.5
124
–40°C to 125°C
0.5
128
0.5
128
0.5
128
0.5
128
–40°C to 85°C
0.5
34
0.5
32
0.5
31
0.5
35
–40°C to 125°C
0.5
34
0.5
32
0.5
31
0.5
35
From input A
to output B
Disable time
Enable time
From input OE
to output B
UNIT
ns
ns
ns
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: SN74AXC8T245-Q1
9
SN74AXC8T245-Q1
www.ti.com
SCES892C – NOVEMBER 2018 – REVISED OCTOBER 2021
6.9 Switching Characteristics, VCCA = 1.2 V
See Figure 7-1 and Figure 7-2 for test circuit and loading conditions. See Figure 7-3 and Figure 7-4 for measurement
waveforms.
B-PORT SUPPLY VOLTAGE (VCCB)
PARAMETER
tpd
tdis
ten
Propagation
delay
Disable time
Enable time
TEST CONDITIONS
0.7 V ± 0.05 V
0.8 V ± 0.04 V
0.9 V ± 0.045 V
1.2 V ± 0.1 V
MIN
MAX
MIN
MAX
MIN
MAX
MIN
MAX
0.5
88
0.5
52
0.5
39
0.5
15
From input A
to output B
–40°C to 85°C
–40°C to 125°C
0.5
88
0.5
52
0.5
39
0.5
15
From input B
to output A
–40°C to 85°C
0.5
49
0.5
32
0.5
23
0.5
15
–40°C to 125°C
0.5
49
0.5
32
0.5
23
0.5
15
From input
OE
to output A
–40°C to 85°C
0.5
87
0.5
87
0.5
87
0.5
87
–40°C to 125°C
0.5
91
0.5
91
0.5
91
0.5
91
From input
OE
to output B
–40°C to 85°C
0.5
119
0.5
94
0.5
85
0.5
89
–40°C to 125°C
0.5
121
0.5
96
0.5
88
0.5
93
From input
OE
to output A
–40°C to 85°C
0.5
34
0.5
34
0.5
34
0.5
34
–40°C to 125°C
0.5
36
0.5
36
0.5
36
0.5
36
From input
OE
to output B
–40°C to 85°C
0.5
168
0.5
98
0.5
61
0.5
29
–40°C to 125°C
0.5
168
0.5
98
0.5
61
0.5
30
UNIT
ns
ns
ns
B-PORT SUPPLY VOLTAGE (VCCB)
PARAMETER
tpd
tdis
ten
10
Propagation
delay
TEST CONDITIONS
1.5 V ± 0.1 V
1.8 V ± 0.15 V
2.5 V ± 0.2 V
3.3 V ± 0.3 V
MIN
MAX
MIN
MAX
MIN
MAX
MIN
MAX
From input A
to output B
–40°C to 85°C
0.5
10
0.5
9
0.5
7
0.5
7
–40°C to 125°C
0.5
10
0.5
9
0.5
7
0.5
8
From input B
to output A
–40°C to 85°C
0.5
13
0.5
11
0.5
8
0.5
7
–40°C to 125°C
0.5
13
0.5
11
0.5
8
0.5
7
From input OE
to output A
–40°C to 85°C
0.5
87
0.5
87
0.5
87
0.5
87
–40°C to 125°C
0.5
91
0.5
91
0.5
91
0.5
91
From input OE
to output B
–40°C to 85°C
0.5
38
0.5
35
0.5
31
0.5
29
–40°C to 125°C
0.5
41
0.5
38
0.5
33
0.5
31
From input OE
to output A
–40°C to 85°C
0.5
34
0.5
34
0.5
34
0.5
34
–40°C to 125°C
0.5
36
0.5
36
0.5
36
0.5
36
From input OE
to output B
–40°C to 85°C
0.5
22
0.5
19
0.5
17
0.5
17
–40°C to 125°C
0.5
23
0.5
20
0.5
18
0.5
18
Disable time
Enable time
Submit Document Feedback
UNIT
ns
ns
ns
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: SN74AXC8T245-Q1
SN74AXC8T245-Q1
www.ti.com
SCES892C – NOVEMBER 2018 – REVISED OCTOBER 2021
6.10 Switching Characteristics, VCCA = 1.5 V
See Figure 7-1 and Figure 7-2 for test circuit and loading conditions. See Figure 7-3 and Figure 7-4 for measurement
waveforms.
B-PORT SUPPLY VOLTAGE (VCCB)
PARAMETER
tpd
tdis
ten
Propagation
delay
TEST CONDITIONS
0.7 V ± 0.05 V
0.9 V ± 0.045 V
1.2 V ± 0.1 V
MIN
MAX
MIN
0.8 V ± 0.04 V
MAX
MIN
MAX
MIN
MAX
From input A
to output B
–40°C to 85°C
0.5
84
0.5
42
0.5
28
0.5
13
–40°C to 125°C
0.5
84
0.5
42
0.5
28
0.5
13
From input B
to output A
–40°C to 85°C
0.5
46
0.5
26
0.5
17
0.5
10
–40°C to 125°C
0.5
46
0.5
26
0.5
17
0.5
10
From input OE
to output A
–40°C to 85°C
0.5
34
0.5
34
0.5
34
0.5
34
–40°C to 125°C
0.5
37
0.5
37
0.5
37
0.5
37
From input OE
to output B
–40°C to 85°C
0.5
115
0.5
89
0.5
80
0.5
85
–40°C to 125°C
0.5
117
0.5
91
0.5
83
0.5
89
From input OE
to output A
–40°C to 85°C
0.5
21
0.5
21
0.5
21
0.5
21
–40°C to 125°C
0.5
23
0.5
23
0.5
23
0.5
23
From input OE
to output B
–40°C to 85°C
0.5
159
0.5
90
0.5
55
0.5
24
–40°C to 125°C
0.5
159
0.5
90
0.5
55
0.5
25
Disable time
Enable time
UNIT
ns
ns
ns
B-PORT SUPPLY VOLTAGE (VCCB)
PARAMETER
tpd
Propagation
delay
TEST CONDITIONS
From input A
to output B
From input B
to output A
From input OE
to output A
tdis
Disable time
From input OE
to output B
From input OE
to output A
ten
Enable time
From input OE
to output B
1.5 V ± 0.1 V
1.8 V ± 0.15 V
2.5 V ± 0.2 V
3.3 V ± 0.3 V
MIN
MAX
MIN
MAX
MIN
MAX
MIN
MAX
–40°C to 85°C
0.5
9
0.5
7
0.5
6
0.5
5
–40°C to 125°C
0.5
9
0.5
7
0.5
6
0.5
6
–40°C to 85°C
0.5
9
0.5
7
0.5
6
0.5
5
–40°C to 125°C
0.5
9
0.5
8
0.5
6
0.5
5
–40°C to 85°C
0.5
34
0.5
34
0.5
34
0.5
34
–40°C to 125°C
0.5
37
0.5
37
0.5
37
0.5
37
–40°C to 85°C
0.5
35
0.5
31
0.5
28
0.5
25
–40°C to 125°C
0.5
38
0.5
34
0.5
31
0.5
27
–40°C to 85°C
0.5
21
0.5
21
0.5
21
0.5
21
–40°C to 125°C
0.5
23
0.5
23
0.5
23
0.5
23
–40°C to 85°C
0.5
17
0.5
15
0.5
12
0.5
11
–40°C to 125°C
0.5
18
0.5
15
0.5
13
0.5
12
UNIT
ns
ns
ns
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: SN74AXC8T245-Q1
11
SN74AXC8T245-Q1
www.ti.com
SCES892C – NOVEMBER 2018 – REVISED OCTOBER 2021
6.11 Switching Characteristics, VCCA = 1.8 V
See Figure 7-1 and Figure 7-2 for test circuit and loading conditions. See Figure 7-3 and Figure 7-4 for measurement
waveforms.
B-PORT SUPPLY VOLTAGE (VCCB)
PARAMETER
tpd
tdis
ten
Propagation
delay
TEST CONDITIONS
0.7 V ± 0.05 V
0.9 V ± 0.045 V
1.2 V ± 0.1 V
MIN
MAX
MIN
0.8 V ± 0.04 V
MAX
MIN
MAX
MIN
MAX
From input A
to output B
–40°C to 85°C
0.5
82
0.5
41
0.5
24
0.5
11
–40°C to 125°C
0.5
82
0.5
41
0.5
24
0.5
11
From input B
to output A
–40°C to 85°C
0.5
49
0.5
25
0.5
15
0.5
9
–40°C to 125°C
0.5
49
0.5
25
0.5
15
0.5
9
From input OE
to output A
–40°C to 85°C
0.5
37
0.5
37
0.5
37
0.5
37
–40°C to 125°C
0.5
40
0.5
40
0.5
40
0.5
40
From input OE
to output B
–40°C to 85°C
0.5
113
0.5
87
0.5
78
0.5
83
–40°C to 125°C
0.5
115
0.5
89
0.5
81
0.5
87
From input OE
to output A
–40°C to 85°C
0.5
17
0.5
17
0.5
17
0.5
17
–40°C to 125°C
0.5
19
0.5
19
0.5
19
0.5
19
From input OE
to output B
–40°C to 85°C
0.5
157
0.5
88
0.5
54
0.5
23
–40°C to 125°C
0.5
157
0.5
88
0.5
54
0.5
23
Disable time
Enable time
UNIT
ns
ns
ns
B-PORT SUPPLY VOLTAGE (VCCB)
PARAMETER
tpd
tdis
ten
12
Propagation
delay
TEST CONDITIONS
1.5 V ± 0.1 V
1.8 V ± 0.15 V
2.5 V ± 0.2 V
3.3 V ± 0.3 V
MIN
MAX
MIN
MAX
MIN
MAX
MIN
MAX
From input A
to output B
–40°C to 85°C
0.5
8
0.5
6
0.5
5
0.5
5
–40°C to 125°C
0.5
8
0.5
7
0.5
6
0.5
5
From input B
to output A
–40°C to 85°C
0.5
7
0.5
6
0.5
5
0.5
4
–40°C to 125°C
0.5
7
0.5
7
0.5
5
0.5
4
From input OE
to output A
–40°C to 85°C
0.5
37
0.5
37
0.5
37
0.5
37
–40°C to 125°C
0.5
40
0.5
40
0.5
40
0.5
40
From input OE
to output B
–40°C to 85°C
0.5
33
0.5
30
0.5
27
0.5
57
–40°C to 125°C
0.5
36
0.5
33
0.5
29
0.5
60
From input OE
to output A
–40°C to 85°C
0.5
17
0.5
17
0.5
17
0.5
17
–40°C to 125°C
0.5
19
0.5
19
0.5
19
0.5
19
From input OE
to output B
–40°C to 85°C
0.5
15
0.5
13
0.5
10
0.5
9
–40°C to 125°C
0.5
16
0.5
14
0.5
11
0.5
10
Disable time
Enable time
Submit Document Feedback
UNIT
ns
ns
ns
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: SN74AXC8T245-Q1
SN74AXC8T245-Q1
www.ti.com
SCES892C – NOVEMBER 2018 – REVISED OCTOBER 2021
6.12 Switching Characteristics, VCCA = 2.5 V
See Figure 7-1 and Figure 7-2 for test circuit and loading conditions. See Figure 7-3 and Figure 7-4 for measurement
waveforms.
B-PORT SUPPLY VOLTAGE (VCCB)
PARAMETER
tpd
tdis
ten
Propagation
delay
TEST CONDITIONS
0.7 V ± 0.05 V
0.9 V ± 0.045 V
1.2 V ± 0.1 V
MIN
MAX
MIN
0.8 V ± 0.04 V
MAX
MIN
MAX
MIN
MAX
From input A
to output B
–40°C to 85°C
0.5
81
0.5
40
0.5
22
0.5
8
–40°C to 125°C
0.5
81
0.5
40
0.5
22
0.5
8
From input B
to output A
–40°C to 85°C
0.5
61
0.5
25
0.5
14
0.5
7
–40°C to 125°C
0.5
61
0.5
25
0.5
14
0.5
7
From input OE
to output A
–40°C to 85°C
0.5
25
0.5
25
0.5
25
0.5
25
–40°C to 125°C
0.5
28
0.5
28
0.5
28
0.5
28
From input OE
to output B
–40°C to 85°C
0.5
111
0.5
85
0.5
76
0.5
81
–40°C to 125°C
0.5
113
0.5
87
0.5
78
0.5
84
From input OE
to output A
–40°C to 85°C
0.5
11
0.5
11
0.5
11
0.5
11
–40°C to 125°C
0.5
12
0.5
12
0.5
12
0.5
12
From input OE
to output B
–40°C to 85°C
0.5
155
0.5
86
0.5
52
0.5
21
–40°C to 125°C
0.5
155
0.5
86
0.5
52
0.5
21
Disable time
Enable time
UNIT
ns
ns
ns
B-PORT SUPPLY VOLTAGE (VCCB)
PARAMETER
tpd
tdis
ten
Propagation
delay
TEST CONDITIONS
1.5 V ± 0.1 V
1.8 V ± 0.15 V
2.5 V ± 0.2 V
3.3 V ± 0.3 V
MIN
MAX
MIN
MAX
MIN
MAX
MIN
MAX
From input A
to output B
–40°C to 85°C
0.5
6
0.5
5
0.5
4
0.5
4
–40°C to 125°C
0.5
6
0.5
5
0.5
5
0.5
4
From input B
to output A
–40°C to 85°C
0.5
6
0.5
5
0.5
4
0.5
4
–40°C to 125°C
0.5
6
0.5
5
0.5
5
0.5
4
From input OE
to output A
–40°C to 85°C
0.5
25
0.5
25
0.5
25
0.5
25
–40°C to 125°C
0.5
28
0.5
28
0.5
28
0.5
28
From input OE
to output B
–40°C to 85°C
0.5
31
0.5
28
0.5
25
0.5
23
–40°C to 125°C
0.5
34
0.5
31
0.5
28
0.5
25
From input OE
to output A
–40°C to 85°C
0.5
11
0.5
11
0.5
11
0.5
11
–40°C to 125°C
0.5
12
0.5
12
0.5
12
0.5
12
From input OE
to output B
–40°C to 85°C
0.5
14
0.5
11
0.5
9
0.5
7
–40°C to 125°C
0.5
14
0.5
12
0.5
9
0.5
8
Disable time
Enable time
UNIT
ns
ns
ns
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: SN74AXC8T245-Q1
13
SN74AXC8T245-Q1
www.ti.com
SCES892C – NOVEMBER 2018 – REVISED OCTOBER 2021
6.13 Switching Characteristics, VCCA = 3.3 V
See Figure 7-1 and Figure 7-2 for test circuit and loading conditions. See Figure 7-3 and Figure 7-4 for measurement
waveforms.
B-PORT SUPPLY VOLTAGE (VCCB)
PARAMETER
tpd
tdis
ten
Propagation
delay
TEST CONDITIONS
0.7 V ± 0.05 V
0.9 V ± 0.045 V
1.2 V ± 0.1 V
MIN
MAX
MIN
0.8 V ± 0.04 V
MAX
MIN
MAX
MIN
MAX
From input A
to output B
–40°C to 85°C
0.5
81
0.5
40
0.5
22
0.5
7
–40°C to 125°C
0.5
81
0.5
40
0.5
22
0.5
7
From input B
to output A
–40°C to 85°C
0.5
142
0.5
35
0.5
17
0.5
7
–40°C to 125°C
0.5
142
0.5
35
0.5
17
0.5
8
From input OE
to output A
–40°C to 85°C
0.5
22
0.5
22
0.5
22
0.5
22
–40°C to 125°C
0.5
24
0.5
24
0.5
24
0.5
24
From input OE
to output B
–40°C to 85°C
0.5
111
0.5
84
0.5
75
0.5
80
–40°C to 125°C
0.5
113
0.5
86
0.5
78
0.5
83
From input OE
to output A
–40°C to 85°C
0.5
9
0.5
9
0.5
9
0.5
9
–40°C to 125°C
0.5
10
0.5
10
0.5
10
0.5
10
From input OE
to output B
–40°C to 85°C
0.5
154
0.5
86
0.5
51
0.5
20
–40°C to 125°C
0.5
154
0.5
86
0.5
51
0.5
20
Disable time
Enable time
UNIT
ns
ns
ns
B-PORT SUPPLY VOLTAGE (VCCB)
PARAMETER
TEST CONDITIONS
1.5 V ± 0.1 V
MIN
tpd
tdis
ten
14
Propagation
delay
MAX
1.8 V ± 0.15 V
MIN
MAX
2.5 V ± 0.2 V
MIN
MAX
3.3 V ± 0.3 V
MIN
–40°C to 85°C
0.5
5
0.5
4
0.5
4
0.5
4
–40°C to 125°C
0.5
5
0.5
4
0.5
4
0.5
4
–40°C to 85°C
0.5
5
0.5
5
0.5
4
0.5
4
–40°C to 125°C
0.5
6
0.5
5
0.5
4
0.5
4
From input OE
to output A
–40°C to 85°C
0.5
22
0.5
22
0.5
22
0.5
22
–40°C to 125°C
0.5
24
0.5
24
0.5
24
0.5
24
From input OE
to output B
–40°C to 85°C
0.5
30
0.5
27
0.5
25
0.5
23
25
From input A
to output B
From input B
to output A
Disable time
–40°C to 125°C
0.5
33
0.5
30
0.5
27
0.5
From input OE
to output A
–40°C to 85°C
0.5
9
0.5
9
0.5
9
0.5
9
–40°C to 125°C
0.5
10
0.5
10
0.5
10
0.5
10
From input OE
to output B
–40°C to 85°C
0.5
13
0.5
10
0.5
8
0.5
7
–40°C to 125°C
0.5
14
0.5
11
0.5
8
0.5
7
Enable time
Submit Document Feedback
UNIT
MAX
ns
ns
ns
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: SN74AXC8T245-Q1
SN74AXC8T245-Q1
www.ti.com
SCES892C – NOVEMBER 2018 – REVISED OCTOBER 2021
6.14 Operating Characteristics: TA = 25°C
PARAMETER
CpdA
CpdA
CpdA
CpdA
Power dissipation
capacitance per transceiver
(A to B: outputs enabled)
Power dissipation
capacitance per transceiver
(A to B: outputs disabled)
Power dissipation
capacitance per transceiver
(B to A: outputs enabled)
Power dissipation
capacitance per transceiver
(B to A: outputs disabled)
TEST CONDITIONS
CL = 0, RL = Open
f = 1 MHz, tr = tf = 1 ns
CL = 0, RL = Open
f = 1 MHz, tr = tf = 1 ns
CL = 0, RL = Open
f = 1 MHz, tr = tf = 1 ns
CL = 0, RL = Open
f = 1 MHz, tr = tf = 1 ns
MIN
TYP
VCCA = VCCB = 0.7 V
1.2
VCCA = VCCB = 0.8 V
1.8
VCCA = VCCB = 0.9 V
1.8
VCCA = VCCB = 1.2 V
1.7
VCCA = VCCB = 1.5 V
1.7
VCCA = VCCB = 1.8 V
1.7
VCCA = VCCB = 2.5 V
2
VCCA = VCCB = 3.3 V
2.5
VCCA = VCCB = 0.7 V
1.1
VCCA = VCCB = 0.8 V
1.8
VCCA = VCCB = 0.9 V
1.8
VCCA = VCCB = 1.2 V
1.7
VCCA = VCCB = 1.5 V
1.7
VCCA = VCCB = 1.8 V
1.7
VCCA = VCCB = 2.5 V
2
VCCA = VCCB = 3.3 V
2.1
VCCA = VCCB = 0.7 V
9.3
VCCA = VCCB = 0.8 V
11.8
VCCA = VCCB = 0.9 V
11.8
VCCA = VCCB = 1.2 V
12
VCCA = VCCB = 1.5 V
12.2
VCCA = VCCB = 1.8 V
13
VCCA = VCCB = 2.5 V
16.4
VCCA = VCCB = 3.3 V
18.1
VCCA = VCCB = 0.7 V
2.6
VCCA = VCCB = 0.8 V
1.2
VCCA = VCCB = 0.9 V
1.1
VCCA = VCCB = 1.2 V
1.2
VCCA = VCCB = 1.5 V
1.2
VCCA = VCCB = 1.8 V
1.3
VCCA = VCCB = 2.5 V
1.6
VCCA = VCCB = 3.3 V
3.9
MAX
UNIT
pF
pF
pF
pF
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: SN74AXC8T245-Q1
15
SN74AXC8T245-Q1
www.ti.com
SCES892C – NOVEMBER 2018 – REVISED OCTOBER 2021
6.14 Operating Characteristics: TA = 25°C (continued)
PARAMETER
CpdB
CpdB
CpdB
CpdB
16
Power dissipation
capacitance per transceiver
(A to B: outputs enabled)
Power dissipation
capacitance per transceiver
(A to B: outputs disabled)
Power dissipation
capacitance per transceiver
(B to A: outputs enabled)
Power dissipation
capacitance per transceiver
(B to A: outputs disabled)
TEST CONDITIONS
CL = 0, RL = Open
f = 1 MHz, tr = tf = 1 ns
CL = 0, RL = Open
f = 1 MHz, tr = tf = 1 ns
CL = 0, RL = Open
f = 1 MHz, tr = tf = 1 ns
CL = 0, RL = Open
f = 1 MHz, tr = tf = 1 ns
MIN
TYP
VCCA = VCCB = 0.7 V
9.3
VCCA = VCCB = 0.8 V
11.7
VCCA = VCCB = 0.9 V
11.8
VCCA = VCCB = 1.2 V
11.9
VCCA = VCCB = 1.5 V
12.2
VCCA = VCCB = 1.8 V
12.9
VCCA = VCCB = 2.5 V
16.3
VCCA = VCCB = 3.3 V
18
VCCA = VCCB = 0.7 V
2.6
VCCA = VCCB = 0.8 V
11.7
VCCA = VCCB = 0.9 V
11.8
VCCA = VCCB = 1.2 V
11.9
VCCA = VCCB = 1.5 V
12.2
VCCA = VCCB = 1.8 V
12.9
VCCA = VCCB = 2.5 V
16.3
VCCA = VCCB = 3.3 V
3.9
VCCA = VCCB = 0.7 V
1.2
VCCA = VCCB = 0.8 V
1.8
VCCA = VCCB = 0.9 V
1.8
VCCA = VCCB = 1.2 V
1.7
VCCA = VCCB = 1.5 V
1.7
VCCA = VCCB = 1.8 V
1.7
VCCA = VCCB = 2.5 V
2
VCCA = VCCB = 3.3 V
2.5
VCCA = VCCB = 0.7 V
1.1
VCCA = VCCB = 0.8 V
1.8
VCCA = VCCB = 0.9 V
1.8
VCCA = VCCB = 1.2 V
1.7
VCCA = VCCB = 1.5 V
1.7
VCCA = VCCB = 1.8 V
1.7
VCCA = VCCB = 2.5 V
2
VCCA = VCCB = 3.3 V
2.1
Submit Document Feedback
MAX
UNIT
pF
pF
pF
pF
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: SN74AXC8T245-Q1
SN74AXC8T245-Q1
www.ti.com
SCES892C – NOVEMBER 2018 – REVISED OCTOBER 2021
6.15 Typical Characteristics
3.4
VCC = 1.8V
VCC = 2.5V
VCC = 3.3V
3.2
3
2.6
VOH (V)
VOH (V)
2.8
2.4
2.2
2
1.8
1.6
1.4
0
2
4
6
8
10
12
IOH (mA)
14
16
18
D001
VCC = 0.7V
VCC = 1.2V
0
20
Figure 6-1. Typical (TA=25°C) Output High Voltage
(VOH) vs Source Current (IOH)
0.5
1
1.5
2
2.5
3
IOH (mA)
3.5
4
4.5
5
D001
Figure 6-2. Typical (TA=25°C) Output High Voltage
(VOH) vs Source Current (IOH)
220
700
650
600
550
500
450
400
350
300
250
200
150
100
50
0
-50
200
180
160
140
VOL (mV)
VOL (mV)
1.25
1.2
1.15
1.1
1.05
1
0.95
0.9
0.85
0.8
0.75
0.7
0.65
0.6
0.55
120
100
80
60
40
VCC = 1.8V
VCC = 2.5V
VCC = 3.3V
VCC = 0.7V
VCC = 1.2V
20
0
0
2
4
6
8
10
12
IOL (mA)
14
16
18
20
0
0.5
1
D001
Figure 6-3. Typical (TA=25°C) Output High Voltage
(VOL) vs Sink Current (IOL)
1.5
2
2.5
3
IOL (mA)
3.5
4
4.5
5
D001
Figure 6-4. Typical (TA=25°C) Output High Voltage
(VOL) vs Sink Current (IOL)
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: SN74AXC8T245-Q1
17
SN74AXC8T245-Q1
www.ti.com
SCES892C – NOVEMBER 2018 – REVISED OCTOBER 2021
7 Parameter Measurement Information
Unless otherwise noted, all input pulses are supplied by generators having the following characteristics:
• f =1 MHz
• Z0 = 50 Ω
• dv / dt ≤ 1 ns/V
Measurement Point
2 X VCCO
S1
RL
Open
Output Pin
Under Test
GND
CL(1)
A.
RL
CL includes probe and jig capacitance.
Figure 7-1. Load Circuit
Parameter
tpd
ten(1), tdis(1)
ten(2), tdis(2)
A.
B.
VCCO
CL
S1
VTP
2k
15 pF
Open
N/A
0.65 V - 0.95 V 20 k
15 pF
Open
N/A
1.1 V - 3.6 V
RL
3 V - 3.6 V
2k
15 pF
2 X VCCO
0.3 V
1.65 V - 2.7 V
2k
15 pF
2 X VCCO
0.15 V
1.1 V - 1.6 V
2k
15 pF
2 X VCCO
0.1 V
0.65 V - 0.95 V 20 k
15 pF
2 X VCCO
0.1 V
3 V - 3.6 V
2k
15 pF
GND
0.3 V
1.65V - 2.7 V
2k
15 pF
GND
0.15 V
1.1 V - 1.6 V
2k
15 pF
GND
0.1 V
0.65 V - 0.95 V 20 k
15 pF
GND
0.1 V
Output waveform on the conditions that input is driven to a valid Logic Low.
Output waveform on the condition that input is driven to a valid Logic High.
Figure 7-2. Load Circuit Conditions
VCCI(1)
An, Bn Input
VCCI / 2
VCCI / 2
GND
tpd
tpd
VOH(2)
Bn, An Output
VCCO / 2
VCCO / 2
VOL(2)
A.
B.
VCCI is the supply pin associated with the input port.
VOH and VOL are typical output voltage levels with specified RL, CL, and S1.
Figure 7-3. Propagation Delay
18
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: SN74AXC8T245-Q1
SN74AXC8T245-Q1
www.ti.com
SCES892C – NOVEMBER 2018 – REVISED OCTOBER 2021
VCCA
OE
VCCA / 2
VCCA / 2
GND
tdis
ten
VCCO(3)
Output(1)
VCCO / 2
VOL + VTP
VOL(4)
VOH(4)
VOH - VTP
Output(2)
VCCO / 2
GND
A.
B.
C.
D.
Output waveform on the condition that input is driven to a valid Logic Low.
Output waveform on the condition that input is driven to a valid Logic High.
VCCO is the supply pin associated with the output port.
VOH and VOL are typical output voltage levels with specified RL, CL, and S1.
Figure 7-4. Enable Time And Disable Time
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: SN74AXC8T245-Q1
19
SN74AXC8T245-Q1
www.ti.com
SCES892C – NOVEMBER 2018 – REVISED OCTOBER 2021
8 Detailed Description
8.1 Overview
The SN74AXC8T245-Q1 device is an 8-bit, dual-supply non-inverting transceiver with bidirectional voltage level
translation. The I/O pins labeled with A and the control pins (DIR1, DIR2, and OE) are supported by VCCA, and
the I/O pins labeled with B are supported by VCCB. The A port and the B port are able to accept I/O voltages
ranging from 0.65 V to 3.6 V.
8.2 Functional Block Diagram
OE
DIR1
Control Block To Enable or
Disable Outputs (Note: Inputs
on each buffer are always
enabled)
DIR2
20
VCCA
VCCB
GND
A1
B1
A2
B2
A3
B3
A4
B4
A5
B5
A6
B6
A7
B7
A8
B8
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: SN74AXC8T245-Q1
SN74AXC8T245-Q1
www.ti.com
SCES892C – NOVEMBER 2018 – REVISED OCTOBER 2021
8.3 Feature Description
8.3.1 Up-Translation and Down-Translation From 0.65 V to 3.6 V
Both supply pins are configured from 0.65 V to 3.6 V, which makes the device suitable for translating between
any of the low voltage nodes (0.7 V, 0.8 V, 0.9 V, 1.2 V, 1.8 V, 2.5 V, and 3.3 V).
8.3.2 Multiple Direction Control Pins
Two control pins are used to configure the 8 data I/Os. I/O channels 1 through 4 are grouped together and
I/O channels 5 through 8 are banked together. The benefit of this is to permit simultaneous up-translation and
down-translation within one device. This eliminates the need for multiple devices, where each device can only
provide up-translation or down-translation sequentially. Simultaneous up and down translation is supported when
both VCCA and VCCB are at least 1.40 V.
8.3.3 Ioff Supports Partial-Power-Down Mode Operation
This feature is to limit the leakage current of an I/O pin being driven to a voltage as large as 3.6 V while having
its corresponding power supply rail powered down. This is represented by the Ioff parameter in the Electrical
Characteristics table.
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: SN74AXC8T245-Q1
21
SN74AXC8T245-Q1
www.ti.com
SCES892C – NOVEMBER 2018 – REVISED OCTOBER 2021
8.3.4 Wettable Flanks
This device includes wettable flanks for at least one package. See the Features section on the front page of the
data sheet for which packages include this feature.
Package
Package
Solder
Weable Flank Lead
Standard Lead
Pad
PCB
Figure 8-1. Simplified Cutaway View of Wettable-Flank QFN Package and Standard QFN Package After
Soldering
Wettable flanks help improve side wetting after soldering which makes QFN packages easier to inspect with
automatic optical inspection (AOI). A wettable flank can be dimpled or step-cut to provide additional surface
area for solder adhesion which assists in reliably creating a side fillet as shown in Figure 8-1. Please see the
mechanical drawing for additional details.
8.4 Device Functional Modes
All control inputs are referenced to VCCA and must be driven to a valid Logic High or Logic Low (that is, not
floating) to assure proper device operation and to prevent excessive power consumption. Table 8-1 summarizes
the possible modes of device operation based on the configuration of the control inputs.
Table 8-1. Function Table
CONTROL
(1)
22
INPUTS(1)
Signal Direction
OE
DIR1
DIR2
H
X
X
L
L
L
L
L
H
L
H
L
L
H
H
Bits 1:4
Bits 5:8
Disabled (Hi-Z)
B to A
B to A
A to B
A to B
A to B
B to A
Input circuits of the data I/Os are always active and must be driven to a valid logic level.
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: SN74AXC8T245-Q1
SN74AXC8T245-Q1
www.ti.com
SCES892C – NOVEMBER 2018 – REVISED OCTOBER 2021
9 Application and Implementation
Note
Information in the following applications sections is not part of the TI component specification,
and TI does not warrant its accuracy or completeness. TI’s customers are responsible for
determining suitability of components for their purposes, as well as validating and testing their design
implementation to confirm system functionality.
9.1 Application Information
The AEC-Q100 qualified SN74AXC8T245-Q1 device can be used in level-translation applications for interfacing
devices or systems operating at different voltage nodes. Figure 9-1 depicts an application in which the
SN74AXC8T245-Q1 device is up-translating a 0.7 V input to a 3.3 V output to interface between a system
controller and a peripheral device.
9.2 Typical Application
0.7 V
3.3 V
0.1 µF
0.1 µF
10
NŸ
10
NŸ
VCCA
VCCB
OE
DIR1
DIR2
10
NŸ
GND
Controller
SN74AXC8T245-Q1
Peripheral
A1
B1
A2
B2
A3
B3
A4
B4
A5
B5
A6
B6
A7
B7
A8
B8
Figure 9-1. Typical Application Schematic
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: SN74AXC8T245-Q1
23
SN74AXC8T245-Q1
www.ti.com
SCES892C – NOVEMBER 2018 – REVISED OCTOBER 2021
9.2.1 Design Requirements
For this design example, use the parameters listed in Table 9-1.
Table 9-1. Design Parameters
DESIGN PARAMETERS
EXAMPLE VALUE
Input voltage range
0.65 V to 3.6 V
Output voltage range
0.65 V to 3.6 V
9.2.2 Detailed Design Procedure
To begin the design process, determine the following:
• Input voltage range
– Use the supply voltage of the device that is driving the SN74AXC8T245-Q1 device to determine the input
voltage range. For a valid logic high the value must exceed the VIH of the input port. For a valid logic low
the value must be less than the VIL of the input port.
• Output voltage range
– Use the supply voltage of the device that the SN74AXC8T245-Q1 device is driving to determine the output
voltage range.
9.2.3 Application Curve
Figure 9-2. Translation Up (0.7 V to 3.3 V) at 2.5 MHz
24
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: SN74AXC8T245-Q1
SN74AXC8T245-Q1
www.ti.com
SCES892C – NOVEMBER 2018 – REVISED OCTOBER 2021
10 Power Supply Recommendations
Always apply a ground reference to the GND pins first. There are no additional requirements for power supply
sequencing.
This device was designed with various power supply sequencing methods in mind to help prevent unintended
triggering of downstream devices. For more information regarding the power up glitch performance of the AXC
family of level translators, see the Power Sequencing for AXC Family of Devices application report.
11 Layout
11.1 Layout Guidelines
To assure reliability of the device, follow common printed-circuit board layout guidelines.
• Use bypass capacitors on power supplies.
• Use short trace lengths to avoid excessive loading.
• Place pads on the signal paths for loading capacitors or pullup resistors to help adjust rise and fall times of
signals depending on the system requirements.
11.2 Layout Example
LEGEND
Polygonal Copper Pour
VIA to Power Plane (Inner Layer)
VIA to GND Plane (Inner Layer)
Bypass Capacitor
Bypass
Capacitor
VCCA
1
VCCA
VCCB
24
2
DIR1
VCCB
23
From Source
3
A1
OE
22
From Source
4
A2
B1
21
To Destination
From Source
5
A3
B2
20
To Destination
From Source
6
A4
B3
19
To Destination
From Source
7
A5
B4
18
To Destination
From Source
8
A6
B5
17
To Destination
From Source
9
A7
B6
16
To Destination
From Source
10
A8
B7
15
To Destination
11
DIR2
B8
14
To Destination
12
GND
GND
13
SN74AXC8T245-Q1
(PW Package)
Figure 11-1. SN74AXC8T245-Q1 Device Layout Example
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: SN74AXC8T245-Q1
25
SN74AXC8T245-Q1
www.ti.com
SCES892C – NOVEMBER 2018 – REVISED OCTOBER 2021
12 Device and Documentation Support
12.1 Documentation Support
12.1.1 Related Documentation
For related documentation, see the following:
• Texas Instruments, SN74AXC8245-Q1 Evaluation Module user's guide
• Texas Instruments, Implications of Slow or Floating CMOS Inputs application report
• Texas Instruments, Power Sequencing for AXC Family of Devices application report
12.2 Receiving Notification of Documentation Updates
To receive notification of documentation updates, navigate to the device product folder on ti.com. Click on
Subscribe to updates to register and receive a weekly digest of any product information that has changed. For
change details, review the revision history included in any revised document.
12.3 Support Resources
TI E2E™ support forums are an engineer's go-to source for fast, verified answers and design help — straight
from the experts. Search existing answers or ask your own question to get the quick design help you need.
Linked content is provided "AS IS" by the respective contributors. They do not constitute TI specifications and do
not necessarily reflect TI's views; see TI's Terms of Use.
12.4 Trademarks
TI E2E™ is a trademark of Texas Instruments.
All trademarks are the property of their respective owners.
12.5 Electrostatic Discharge Caution
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled
with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may
be more susceptible to damage because very small parametric changes could cause the device not to meet its published
specifications.
13 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
26
Submit Document Feedback
Copyright © 2021 Texas Instruments Incorporated
Product Folder Links: SN74AXC8T245-Q1
PACKAGE OPTION ADDENDUM
www.ti.com
8-Nov-2021
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
(2)
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
(4/5)
(6)
CAXC8T245QRHLRQ1
ACTIVE
VQFN
RHL
24
1000
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
AX8T245Q
CAXC8T245QWRGYRQ1
ACTIVE
VQFN
RGY
24
3000
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 125
AX8T245Q
SN74AXC8T245QPWRQ1
ACTIVE
TSSOP
PW
24
2000
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
AX8T245Q
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of
工商网监
湘ICP备2023018690号
