SN74CB3Q3245PWE4

SN74CB3Q3245 8-BIT FET BUS SWITCH 2.5-V/3.3-V LOW-VOLTAGE HIGH-BANDWIDTH BUS SWITCH www.ti.com SCDS124B – JULY 2003 – REVISED MARCH 2005 • • • (1) For additional information regarding the performance characteristics of the CB3Q family, refer to the TI application report, CBT-C, CB3T, and CB3Q Signal-Switch Families, literature number SCDA008. • • • • DBQ, DGV, OR PW PACKAGE (TOP VIEW) NC A1 A2 A3 A4 A5 A6 A7 A8 GND 1 20 2 19 3 18 4 17 5 16 6 15 7 14 8 13 9 12 10 11 VCC OE B1 B2 B3 B4 B5 B6 B7 B8 NC - No internal connection RGY PACKAGE (TOP VIEW) A1 A2 A3 A4 A5 A6 A7 A8 VCC • • 1 20 3 4 19 OE 18 B1 17 B2 5 6 16 B3 15 B4 7 8 14 B5 13 B6 2 12 B7 9 10 11 B8 • • • • Data and Control Inputs Provide Undershoot Clamp Diodes Low Power Consumption (ICC = 1 mA Typical) VCC Operating Range From 2.3 V to 3.6 V Data I/Os Support 0- to 5-V Signaling Levels (0.8 V, 1.2 V, 1.5 V, 1.8 V, 2.5 V, 3.3 V, 5 V) Control Inputs Can Be Driven by TTL or 5-V/3.3-V CMOS Outputs Ioff Supports Partial-Power-Down Mode Operation Latch-Up Performance Exceeds 100 mA Per JESD 78, Class II ESD Performance Tested Per JESD 22 – 2000-V Human-Body Model (A114-B, Class II) – 1000-V Charged-Device Model (C101) Supports Both Digital and Analog Applications: PCI Interface, Differential Signal Interface, Memory Interleaving, Bus Isolation, Low-Distortion Signal Gating NC • • High-Bandwidth Data Path (up to 500 MHz (1)) Equivalent to IDTQS3VH384 Device 5-V Tolerant I/Os With Device Powered Up or Powered Down Low and Flat ON-State Resistance (ron) Characteristics Over Operating Range (ron = 4 Ω Typ) Rail-to-Rail Switching on Data I/O Ports – 0- to 5-V Switching With 3.3-V VCC – 0- to 3.3-V Switching With 2.5-V VCC Bidirectional Data Flow With Near-Zero Propagation Delay Low Input/Output Capacitance Minimizes Loading and Signal Distortion (Cio(OFF) = 3.5 pF Typ) Fast Switching Frequency (fOE = 20 MHz Max) GND • FEATURES • NC - No internal connection DESCRIPTION/ORDERING INFORMATION The SN74CB3Q3245 is a high-bandwidth FET bus switch utilizing a charge pump to elevate the gate voltage of the pass transistor, providing a low and flat ON-state resistance (ron). The low and flat ON-state resistance allows for minimal propagation delay and supports rail-to-rail switching on the data input/output (I/O) ports. The device also features low data I/O capacitance to minimize capacitive loading and signal distortion on the data bus. Specifically designed to support high-bandwidth applications, the SN74CB3Q3245 provides an optimized interface solution ideally suited for broadband communications, networking, and data-intensive computing systems. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright © 2003–2005, Texas Instruments Incorporated SN74CB3Q3245 8-BIT FET BUS SWITCH 2.5-V/3.3-V LOW-VOLTAGE HIGH-BANDWIDTH BUS SWITCH www.ti.com SCDS124B – JULY 2003 – REVISED MARCH 2005 DESCRIPTION/ORDERING INFORMATION (CONTINUED) The SN74CB3Q3245 is organized as an 8-bit bus switch with a single output-enable (OE) input. When OE is low, the bus switch is ON and the A port is connected to the B port, allowing bidirectional data flow between ports. When OE is high, the bus switch is OFF and a high-impedance state exists between the A and B ports. This device is fully specified for partial-power-down applications using Ioff. The Ioff circuitry prevents damaging current backflow through the device when it is powered down. The device has isolation during power off. To ensure the high-impedance state during power up or power down, OE should be tied to VCC through a pullup resistor; the minimum value of the resistor is determined by the current-sinking capability of the driver. ORDERING INFORMATION PACKAGE (1) TA –40°C to 85°C (1) ORDERABLE PART NUMBER Tape and reel SN74CB3Q3245RGYR BU245 SSOP (QSOP) – DBQ Tape and reel SN74CB3Q3245DBQR CB3Q3245 Tube SN74CB3Q3245PW Tape and reel SN74CB3Q3245PWR TVSOP – DGV Tape and reel SN74CB3Q3245DGVR BU245 VFBGA – GQN Tape and reel SN74CB3Q3245GQNR BU245 TSSOP – PW BU245 Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. GQN PACKAGE (TOP VIEW) TERMINAL ASSIGNMENTS (1) 1 2 3 4 A A1 NC VCC OE A B A3 B2 A2 B1 B C A5 A4 B4 B3 C D A7 B6 A6 B5 D E GND A8 B8 B7 1 2 3 4 E (1) NC - No internal connection FUNCTION TABLE 2 TOP-SIDE MARKING QFN – RGY INPUT OE INPUT/OUTPUT A FUNCTION L B A port = B port H Z Disconnect SN74CB3Q3245 8-BIT FET BUS SWITCH 2.5-V/3.3-V LOW-VOLTAGE HIGH-BANDWIDTH BUS SWITCH www.ti.com SCDS124B – JULY 2003 – REVISED MARCH 2005 LOGIC DIAGRAM (POSITIVE LOGIC) 2 18 A1 B1 SW 9 11 A8 SW B8 19 OE Pin numbers shown are for the DBQ, DGV, PW, and RGY packages. SIMPLIFIED SCHEMATIC, EACH FET SWITCH (SW) A B VCC Charge Pump EN(1) (1) EN is the internal enable signal applied to the switch. 3 SN74CB3Q3245 8-BIT FET BUS SWITCH 2.5-V/3.3-V LOW-VOLTAGE HIGH-BANDWIDTH BUS SWITCH www.ti.com SCDS124B – JULY 2003 – REVISED MARCH 2005 Absolute Maximum Ratings (1) over operating free-air temperature range (unless otherwise noted) MIN MAX VCC Supply voltage range –0.5 4.6 V VIN Control input voltage range (2) (3) –0.5 7 V VI/O Switch I/O voltage range (2) (3) (4) IIK Control input clamp current VIN < 0 –50 mA II/OK I/O port clamp current VI/O < 0 –50 mA ±64 mA ±100 mA IIO ON-state switch –0.5 current (5) Continuous current through VCC or GND θJA Tstg (1) (2) (3) (4) (5) (6) (7) Package thermal impedance 7 DBQ package (6) 68 DGV package (6) 92 GQN package (6) 78 PW package (6) 83 RGY package (7) 37 Storage temperature range –65 UNIT V °C/W °C 150 Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. All voltages are with respect to ground, unless otherwise specified. The input and output voltage ratings may be exceeded if the input and output clamp-current ratings are observed. VI and VO are used to denote specific conditions for VI/O. II and IO are used to denote specific conditions for II/O. The package thermal impedance is calculated in accordance with JESD 51-7. The package thermal impedance is calculated in accordance with JESD 51-5. Recommended Operating Conditions (1) MIN MAX VCC Supply voltage VIH High-level control input voltage VIL Low-level control input voltage VI/O Data input/output voltage TA Operating free-air temperature (1) 4 UNIT 2.3 3.6 VCC = 2.3 V to 2.7 V 1.7 5.5 V VCC = 2.7 V to 3.6 V 2 5.5 VCC = 2.3 V to 2.7 V 0 0.7 VCC = 2.7 V to 3.6 V 0 0.8 0 5.5 V –40 85 °C V V All unused control inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report, Implications of Slow or Floating CMOS Inputs, literature number SCBA004. SN74CB3Q3245 8-BIT FET BUS SWITCH 2.5-V/3.3-V LOW-VOLTAGE HIGH-BANDWIDTH BUS SWITCH www.ti.com SCDS124B – JULY 2003 – REVISED MARCH 2005 Electrical Characteristics (1) over recommended operating free-air temperature range (unless otherwise noted) PARAMETER VIK MIN TYP (2) MAX TEST CONDITIONS VCC = 3.6 V, II = –18 mA VCC = 3.6 V, VIN = 0 to 5.5 V IOZ (3) VCC = 3.6 V, VO = 0 to 5.5 V, VI = 0, Switch OFF, VIN = VCC or GND Ioff VCC = 0, VO = 0 to 5.5 V, VI = 0 ICC VCC = 3.6 V, II/O = 0, Switch ON or OFF, VIN = VCC or GND Control inputs VCC = 3.6 V, One input at 3 V, Other inputs at VCC or GND ICCD (5) Per control input VCC = 3.6 V, A and B ports open, Cin Control inputs VCC = 3.3 V, VIN = 5.5 V, 3.3 V, or 0 Cio(OFF) VCC = 3.3 V, Switch OFF, VIN = VCC or GND, Cio(ON) VCC = 3.3 V, IIN Control inputs ∆ICC (4) ron (6) VCC = 3 V (1) (2) (3) (4) (5) (6) V ±1 µA ±1 µA 1 µA 2 mA 30 µA 1 0.30 0.35 mA/ MHz 2.5 3.5 pF VI/O = 5.5 V, 3.3 V, or 0 3.5 5 pF Switch ON, VIN = VCC or GND, VI/O = 5.5 V, 3.3 V, or 0 9 11 pF VI = 0, IO = 30 mA 4 8 VI = 1.7 V, IO = –15 mA 4.5 9 VI = 0, IO = 30 mA 4 6 VI = 2.4 V, IO = –15 mA 4 8 Control input switching at 50% duty cycle VCC = 2.3 V, TYP at VCC = 2.5 V UNIT –1.8 Ω VIN and IIN refer to control inputs. VI, VO, II, and IO refer to data pins. All typical values are at VCC = 3.3 V (unless otherwise noted), TA = 25°C. For I/O ports, the parameter IOZ includes the input leakage current. This is the increase in supply current for each input that is at the specified TTL voltage level, rather than VCC or GND. This parameter specifies the dynamic power-supply current associated with the operating frequency of a single control input (see Figure 2). Measured by the voltage drop between the A and B terminals at the indicated current through the switch. ON-state resistance is determined by the lower of the voltages of the two (A or B) terminals. Switching Characteristics over recommended operating free-air temperature range (unless otherwise noted) (see Figure 3) (1) (2) VCC = 2.5 V ± 0.2 V VCC = 3.3 V ± 0.3 V FROM (INPUT) TO (OUTPUT) fOE (1) OE A or B 10 20 tpd (2) A or B B or A 0.12 0.20 ns ten OE A or B 1.5 7.5 1.5 6.5 ns tdis OE A or B 1 6.5 1 6.5 ns PARAMETER MIN MAX MIN UNIT MAX MHz Maximum switching frequency for control input (VO > VCC, VI = 5 V, RL ≥ 1 MΩ, CL = 0) The propagation delay is the calculated RC time constant of the typical ON-state resistance of the switch and the specified load capacitance, when driven by an ideal voltage source (zero output impedance). 5 SN74CB3Q3245 8-BIT FET BUS SWITCH 2.5-V/3.3-V LOW-VOLTAGE HIGH-BANDWIDTH BUS SWITCH www.ti.com SCDS124B – JULY 2003 – REVISED MARCH 2005 TYPICAL ron vs VI 16 Ω VCC = 3.3 V TA = 25°C IO = -15 mA r on - ON-State Resistance - 14 12 10 8 6 4 2 0 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 14 16 18 20 VI - V Figure 1. Typical ron vs VI TYPICAL ICC vs OE SWITCHING FREQUENCY 12 VCC = 3.3 V TA = 25°C A and B Ports Open 10 ICC − mA 8 6 4 2 0 0 2 4 6 8 10 12 OE Switching Frequency − MHz Figure 2. Typical ICC vs OE Switching Frequency 6 SN74CB3Q3245 8-BIT FET BUS SWITCH 2.5-V/3.3-V LOW-VOLTAGE HIGH-BANDWIDTH BUS SWITCH www.ti.com SCDS124B – JULY 2003 – REVISED MARCH 2005 PARAMETER MEASUREMENT INFORMATION VCC Input Generator VIN 50 Ω 50 Ω VG1 TEST CIRCUIT DUT 2 × VCC Input Generator S1 RL VO VI 50 Ω 50 Ω VG2 CL (see Note A) RL TEST VCC S1 RL VI CL tpd(s) 2.5 V ± 0.2 V 3.3 V ± 0.3 V Open Open 500 Ω 500 Ω VCC or GND VCC or GND 30 pF 50 pF tPLZ/tPZL 2.5 V ± 0.2 V 3.3 V ± 0.3 V 2 × VCC 2 × VCC 500 Ω 500 Ω GND GND 30 pF 50 pF 0.15 V 0.3 V tPHZ/tPZH 2.5 V ± 0.2 V 3.3 V ± 0.3 V GND GND 500 Ω 500 Ω VCC VCC 30 pF 50 pF 0.15 V 0.3 V V∆ VCC Output Control (VIN) VCC/2 VCC VCC/2 VCC/2 0V tPLH VOH Output VCC/2 VCC/2 VOL VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES (tpd(s)) Output Waveform 1 S1 at 2 × VCC (see Note B) tPLZ VCC VCC/2 VOL + V∆ VOL tPZH tPHL VCC/2 0V tPZL Output Control (VIN) Open GND Output Waveform 2 S1 at GND (see Note B) tPHZ VOH VCC/2 VOH − V∆ 0V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low, except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high, except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 10 MHz, ZO = 50 Ω, tr ≤ 2.5 ns, tf ≤ 2.5 ns. D. The outputs are measured one at a time, with one transition per measurement. E. tPLZ and tPHZ are the same as tdis. F. tPZL and tPZH are the same as ten. G. tPLH and tPHL are the same as tpd(s). The tpd propagation delay is the calculated RC time constant of the typical ON-state resistance of the switch and the specified load capacitance, when driven by an ideal voltage source (zero output impedance). H. All parameters and waveforms are not applicable to all devices. Figure 3. Test Circuit and Voltage Waveforms 7 PACKAGE OPTION ADDENDUM www.ti.com 17-Nov-2022 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan (2) Lead finish/ Ball material MSL Peak Temp Op Temp (°C) Device Marking (3) Samples (4/5) (6) 74CB3Q3245RGYRG4 ACTIVE VQFN RGY 20 3000 RoHS & Green NIPDAU Level-2-260C-1 YEAR -40 to 85 BU245 Samples SN74CB3Q3245DBQR ACTIVE SSOP DBQ 20 2500 RoHS & Green NIPDAU Level-2-260C-1 YEAR -40 to 85 CB3Q3245 Samples SN74CB3Q3245DGVR ACTIVE TVSOP DGV 20 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 BU245 Samples SN74CB3Q3245PW ACTIVE TSSOP PW 20 70 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 BU245 Samples SN74CB3Q3245PWR ACTIVE TSSOP PW 20 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 BU245 Samples SN74CB3Q3245PWRE4 ACTIVE TSSOP PW 20 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 85 BU245 Samples SN74CB3Q3245RGYR ACTIVE VQFN RGY 20 3000 RoHS & Green NIPDAU Level-2-260C-1 YEAR -40 to 85 BU245 Samples SN74CB3Q3245ZQNR OBSOLETE BGA MICROSTAR JUNIOR ZQN 20 TBD Call TI Call TI BU245 (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of