SN74LV04ATPWREP

      SCLS563A − JANUARY 2004 − REVISED MAY 2004 D Controlled Baseline D D D D D D D Typical VOLP (Output Ground Bounce) − One Assembly/Test Site, One Fabrication Site Extended Temperature Performance of −40°C to 105°C Enhanced Diminishing Manufacturing Sources (DMS) Support Enhanced Product-Change Notification Qualification Pedigree† 2-V to 5.5-V VCC Operation Max tpd of 7.5 ns at 5 V D D D 2.3 V at VCC = 3.3 V, TA = 25°C Supports Mixed-Mode Voltage Operation on All Ports Ioff Supports Partial-Power-Down Mode Operation PW PACKAGE (TOP VIEW) 1A 1Y 2A 2Y 3A 3Y GND † Component qualification in accordance with JEDEC and industry standards to ensure reliable operation over an extended temperature range. This includes, but is not limited to, Highly Accelerated Stress Test (HAST) or biased 85/85, temperature cycle, autoclave or unbiased HAST, electromigration, bond intermetallic life, and mold compound life. Such qualification testing should not be viewed as justifying use of this component beyond specified performance and environmental limits. 1 14 2 13 3 12 4 11 5 10 6 9 7 8 VCC 6A 6Y 5A 5Y 4A 4Y description/ordering information This hex inverter is designed for 2-V to 5.5-V VCC operation. The SN74LV04A contains six independent inverters. This device performs the Boolean function Y = A. The device is fully specified for partial-power-down applications using Ioff. The Ioff circuitry disables the outputs, preventing damaging current backflow through the device when it is powered down. ORDERING INFORMATION ORDERABLE PART NUMBER PACKAGE‡ TA TOP-SIDE MARKING −40°C to 105°C TSSOP − PW Tape and reel SN74LV04ATPWREP LV04AEP ‡ Package drawings, standard packing quantities, thermal data, symbolization, and PCB design guidelines are available at www.ti.com/sc/package. FUNCTION TABLE (each inverter) INPUT A OUTPUT Y H L L H logic diagram, each inverter (positive logic) A Y Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Copyright  2004, Texas Instruments Incorporated     !   "#$ %!& %   "! "! '! !  !( ! %% )*& % "!+ %!  !!$* $%! !+  $$ "!!& POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 1 
      SCLS563A − JANUARY 2004 − REVISED MAY 2004 absolute maximum ratings over operating free-air temperature range (unless otherwise noted)† Supply voltage range, VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 7 V Input voltage range, VI (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 7 V Voltage range applied to any output in the high-impedance or power-off state, VO (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to 7 V Output voltage range, VO (see Notes 1 and 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.5 V to VCC + 0.5 V Input clamp current, IIK (VI < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −20 mA Output clamp current, IOK (VO < 0) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −50 mA Continuous output current, IO (VO = 0 to VCC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±25 mA Continuous current through VCC or GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±50 mA Package thermal impedance, θJA (see Note 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113°C/W Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C † Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. The input and output negative-voltage ratings may be exceeded if the input and output current ratings are observed. 2. This value is limited to 5.5 V maximum. 3. The package thermal impedance is calculated in accordance with JESD 51-7. recommended operating conditions (see Note 4) VCC VIH Supply voltage High-level input voltage VIL Low-level input voltage VI VO Input voltage IOH IOL ∆t/∆v VCC = 2 V VCC = 2.3 V to 2.7 V VCC = 3 V to 3.6 V VCC = 4.5 V to 5.5 V MIN MAX 2 5.5 0.5 VCC × 0.3 VCC × 0.3 0 0 High-level output current VCC = 3 V to 3.6 V VCC = 4.5 V to 5.5 V Low-level output current VCC × 0.3 5.5 VCC −50 V V V µA −2 −6 mA −12 VCC = 2 V VCC = 2.3 V to 2.7 V 50 VCC = 3 V to 3.6 V VCC = 4.5 V to 5.5 V 6 VCC = 2.3 V to 2.7 V VCC = 3 V to 3.6 V VCC = 4.5 V to 5.5 V Input transition rise or fall rate V VCC × 0.7 VCC = 3 V to 3.6 V VCC = 4.5 V to 5.5 V VCC = 2 V VCC = 2.3 V to 2.7 V V 1.5 VCC × 0.7 VCC × 0.7 VCC = 2 V VCC = 2.3 V to 2.7 V Output voltage UNIT µA 2 mA 12 200 100 ns/V 20 TA Operating free-air temperature −40 105 °C NOTE 4: All unused inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report, Implications of Slow or Floating CMOS Inputs, literature number SCBA004. 2 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 
      SCLS563A − JANUARY 2004 − REVISED MAY 2004 electrical characteristics over recommended operating free-air temperature range (unless otherwise noted) PARAMETER VOH VOL TEST CONDITIONS IOH = −50 µA IOH = −2 mA 2 V to 5.5 V IOH = −6 mA IOH = −12 mA IOL = 50 µA IOL = 2 mA VI = 5.5 V or GND VI = VCC or GND, Ioff VI or VO = 0 to 5.5 V Ci VI = VCC or GND 2.3 V VCC−0.1 2 3V 2.48 4.5 V 3.8 TYP MAX UNIT V 2 V to 5.5 V IOL = 6 mA IOL = 12 mA II ICC MIN VCC 0.1 2.3 V 0.4 3V 0.44 4.5 V 0.55 V 0 to 5.5 V ±1 µA 5.5 V 20 µA 0 5 µA IO = 0 3.3 V 2.3 5V 2.3 pF switching characteristics over recommended operating free-air temperature range, VCC = 2.5 V ± 0.2 V (unless otherwise noted) (see Figure 1) PARAMETER tpd FROM (INPUT) TO (OUTPUT) LOAD CAPACITANCE A Y CL = 50 pF MIN TA = 25°C TYP MAX 10 15.5 MIN MAX 1 18 UNIT ns switching characteristics over recommended operating free-air temperature range, VCC = 3.3 V ± 0.3 V (unless otherwise noted) (see Figure 1) PARAMETER tpd FROM (INPUT) TO (OUTPUT) LOAD CAPACITANCE A Y CL = 50 pF MIN TA = 25°C TYP MAX 7.3 10.6 MIN MAX 1 12 UNIT ns switching characteristics over recommended operating free-air temperature range, VCC = 5 V ± 0.5 V (unless otherwise noted) (see Figure 1) PARAMETER tpd FROM (INPUT) TO (OUTPUT) LOAD CAPACITANCE TA = 25°C MIN TYP MAX A Y CL = 50 pF 5.1 POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 7.5 MIN MAX 1 8.5 UNIT ns 3 
      SCLS563A − JANUARY 2004 − REVISED MAY 2004 noise characteristics, VCC = 3.3 V, CL = 50 pF, TA = 25°C (see Note 5) PARAMETER MIN TYP MAX UNIT VOL(P) VOL(V) Quiet output, maximum dynamic VOL 0.3 0.8 V Quiet output, minimum dynamic VOL −0.1 −0.8 V VOH(V) VIH(D) Quiet output, minimum dynamic VOH 3.1 High-level dynamic input voltage V 2.31 V VIL(D) Low-level dynamic input voltage NOTE 5: Characteristics are for surface-mount packages only. 0.99 V VCC 3.3 V TYP UNIT 5V 11.4 operating characteristics, TA = 25°C PARAMETER Cpd 4 Power dissipation capacitance TEST CONDITIONS CL = 50 pF, POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 f = 10 MHz 9.6 pF 
      SCLS563A − JANUARY 2004 − REVISED MAY 2004 PARAMETER MEASUREMENT INFORMATION From Output Under Test RL = 1 kΩ From Output Under Test Test Point VCC Open S1 TEST GND CL (see Note A) CL (see Note A) S1 tPLH/tPHL tPLZ/tPZL tPHZ/tPZH Open Drain Open VCC GND VCC LOAD CIRCUIT FOR 3-STATE AND OPEN-DRAIN OUTPUTS LOAD CIRCUIT FOR TOTEM-POLE OUTPUTS VCC 50% VCC Timing Input 0V tw tsu VCC 50% VCC Input 50% VCC th VCC 50% VCC Data Input 50% VCC 0V 0V VOLTAGE WAVEFORMS PULSE DURATION VOLTAGE WAVEFORMS SETUP AND HOLD TIMES VCC 50% VCC Input 50% VCC tPLH In-Phase Output 50% VCC VOH 50% VCC VOL VOH 50% VCC VOL VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES INVERTING AND NONINVERTING OUTPUTS 50% VCC 0V Output Waveform 1 S1 at VCC (see Note B) tPLH 50% VCC 50% VCC tPLZ tPZL tPHL tPHL Out-of-Phase Output 0V VCC Output Control ≈VCC 50% VCC tPHZ tPZH Output Waveform 2 S1 at GND (see Note B) VOL + 0.3 V VOL 50% VCC VOH − 0.3 V VOH ≈0 V VOLTAGE WAVEFORMS ENABLE AND DISABLE TIMES LOW- AND HIGH-LEVEL ENABLING NOTES: A. CL includes probe and jig capacitance. B. Waveform 1 is for an output with internal conditions such that the output is low, except when disabled by the output control. Waveform 2 is for an output with internal conditions such that the output is high, except when disabled by the output control. C. All input pulses are supplied by generators having the following characteristics: PRR ≤ 1 MHz, ZO = 50 Ω, tr ≤ 3 ns, tf ≤ 3 ns. D. The outputs are measured one at a time, with one input transition per measurement. E. tPLZ and tPHZ are the same as tdis. F. tPZL and tPZH are the same as ten. G. tPHL and tPLH are the same as tpd. H. All parameters and waveforms are not applicable to all devices. Figure 1. Load Circuit and Voltage Waveforms POST OFFICE BOX 655303 • DALLAS, TEXAS 75265 5 PACKAGE OPTION ADDENDUM www.ti.com 10-Dec-2020 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan (2) Lead finish/ Ball material MSL Peak Temp Op Temp (°C) Device Marking (3) (4/5) (6) SN74LV04ATPWREP ACTIVE TSSOP PW 14 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 105 LV04AEP V62/04691-01XE ACTIVE TSSOP PW 14 2000 RoHS & Green NIPDAU Level-1-260C-UNLIM -40 to 105 LV04AEP (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of