TLC070, TLC071, TLC072, TLC073, TLC074, TLC075, TLC07xA
FAMILY OF WIDE-BANDWIDTH HIGH-OUTPUT-DRIVE SINGLE SUPPLY
OPERATIONAL AMPLIFIERS
SLOS219F − JUNE 1999 − REVISED DECEMBER 2011
D Wide Bandwidth . . . 10 MHz
D High Output Drive
D
D
D
D
D
D
D
Operational Amplifier
− IOH . . . 57 mA at VDD − 1.5 V
− IOL . . . 55 mA at 0.5 V
High Slew Rate
− SR+ . . . 16 V/μs
− SR− . . . 19 V/μs
Wide Supply Range . . . 4.5 V to 16 V
Supply Current . . . 1.9 mA/Channel
Ultralow Power Shutdown Mode
IDD . . . 125 μA/Channel
Low Input Noise Voltage . . . 7 nV√Hz
Input Offset Voltage . . . 60 μV
Ultra-Small Packages
− 8 or 10 Pin MSOP (TLC070/1/2/3)
−
+
description
The first members of TI’s new BiMOS general-purpose operational amplifier family are the TLC07x. The BiMOS
family concept is simple: provide an upgrade path for BiFET users who are moving away from dual-supply to
single-supply systems and demand higher AC and dc performance. With performance rated from 4.5 V to 16
V across commercial (0°C to 70°C) and an extended industrial temperature range (−40°C to 125°C), BiMOS
suits a wide range of audio, automotive, industrial and instrumentation applications. Familiar features like offset
nulling pins, and new features like MSOP PowerPAD™ packages and shutdown modes, enable higher levels
of performance in a variety of applications.
Developed in TI’s patented LBC3 BiCMOS process, the new BiMOS amplifiers combine a very high input
impedance low-noise CMOS front end with a high-drive bipolar output stage, thus providing the optimum
performance features of both. AC performance improvements over the TL07x BiFET predecessors include a
bandwidth of 10 MHz (an increase of 300%) and voltage noise of 7 nV/√Hz (an improvement of 60%). DC
improvements include a factor of 4 reduction in input offset voltage down to 1.5 mV (maximum) in the standard
grade, and a power supply rejection improvement of greater than 40 dB to 130 dB. Added to this list of impressive
features is the ability to drive ±50-mA loads comfortably from an ultrasmall-footprint MSOP PowerPAD package,
which positions the TLC07x as the ideal high-performance general-purpose operational amplifier family.
FAMILY PACKAGE TABLE
PACKAGE TYPES
NO. OF
CHANNELS
MSOP
PDIP
SOIC
TSSOP
TLC070
1
8
8
8
—
TLC071
1
8
8
8
—
TLC072
2
8
8
8
—
—
TLC073
2
10
14
14
—
Yes
TLC074
4
—
14
14
20
—
TLC075
4
—
16
16
20
Yes
DEVICE
SHUTDOWN
UNIVERSAL
EVM BOARD
Yes
Refer to the EVM
Selection Guide
(Lit# SLOU060)
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PowerPAD is a trademark of Texas Instruments. All other trademarks are the property of their respective owners.
Copyright © 2000−2011, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
WWW.TI.COM
1
TLC070, TLC071, TLC072, TLC073, TLC074, TLC075, TLC07xA
FAMILY OF WIDE-BANDWIDTH HIGH-OUTPUT-DRIVE SINGLE SUPPLY
OPERATIONAL AMPLIFIERS
SLOS219F − JUNE 1999 − REVISED DECEMBER 2011
TLC070 and TLC071 AVAILABLE OPTIONS
PACKAGED DEVICES
TA
0°C to 70°C
−40°C
40°C to 125°C
†
SMALL OUTLINE
(D)†
SMALL OUTLINE
(DGN)†
SYMBOL
PLASTIC DIP
(P)
TLC070CD
TLC071CD
TLC070CDGN
TLC071CDGN
xxTIACS
xxTIACU
TLC070CP
TLC071CP
TLC070ID
TLC071ID
TLC070IDGN
TLC071IDGN
xxTIACT
xxTIACV
TLC070IP
TLC071IP
—
—
—
—
TLC070AID
TLC071AID
TLC070AIP
TLC071AIP
This package is available taped and reeled. To order this packaging option, add an R suffix to the part number (e.g., TLC070CDR).
TLC072 and TLC073 AVAILABLE OPTIONS
PACKAGED DEVICES
TA
0°C to 70°C
−40°C
40°C to 125°C
†
‡
SMALL
OUTLINE
(D)†
SYMBOL‡
PLASTIC
DIP
(N)
PLASTIC
DIP
(P)
(DGN)†
SYMBOL‡
(DGQ)†
TLC072CD
TLC073CD
TLC072CDGN
—
xxTIADV
—
—
TLC073CDGQ
—
xxTIADX
—
TLC073CN
TLC072CP
—
TLC072ID
TLC073ID
TLC072IDGN
—
xxTIADW
—
—
TLC073IDGQ
—
xxTIADY
—
TLC073IN
TLC072IP
—
TLC072AID
TLC073AID
—
—
—
—
—
—
—
—
—
TLC073AIN
TLC072AIP
—
MSOP
This package is available taped and reeled. To order this packaging option, add an R suffix to the part number (e.g., TLC072CDR).
xx represents the device date code.
TLC074 and TLC075 AVAILABLE OPTIONS
PACKAGED DEVICES
TA
0°C to 70°C
40°C to 125°C
−40°C
†
2
SMALL OUTLINE
(D)†
PLASTIC DIP
(N)
TSSOP
(PWP)†
TLC074CD
TLC075CD
TLC074CN
TLC075CN
TLC074CPWP
TLC075CPWP
TLC074ID
TLC075ID
TLC074IN
TLC075IN
TLC074IPWP
TLC075IPWP
TLC074AID
TLC075AID
TLC074AIN
TLC075AIN
TLC074AIPWP
TLC075AIPWP
This package is available taped and reeled. To order this packaging option, add an R suffix to the part number (e.g.,
TLC074CDR).
WWW.TI.COM
TLC070, TLC071, TLC072, TLC073, TLC074, TLC075, TLC07xA
FAMILY OF WIDE-BANDWIDTH HIGH-OUTPUT-DRIVE SINGLE SUPPLY
OPERATIONAL AMPLIFIERS
SLOS219F − JUNE 1999 − REVISED DECEMBER 2011
TLC07x PACKAGE PIN OUTS
TLC070
D, DGN OR P PACKAGE
(TOP VIEW)
NULL
IN −
IN +
GND
1
8
2
7
3
6
4
5
TLC071
D, DGN OR P PACKAGE
(TOP VIEW)
SHDN
VDD
OUT
NULL
NULL
IN −
IN +
GND
TLC073
DGQ PACKAGE
(TOP VIEW)
1OUT
1IN −
1IN+
GND
1SHDN
1
2
3
4
5
10
9
8
7
6
VDD
2OUT
2IN −
2IN+
2SHDN
1
20
2
19
3
18
4
17
5
16
6
15
7
14
8
13
9
12
10
11
7
3
6
4
5
NC
VDD
OUT
NULL
1OUT
1IN −
1IN +
GND
1OUT
1IN −
1IN+
VDD
2IN+
2IN −
2OUT
1/2SHDN
8
2
7
3
6
4
5
(TOP VIEW)
(TOP VIEW)
1
14
2
13
3
12
4
11
5
10
6
9
7
8
VDD
2OUT
2IN −
2IN+
NC
2SHDN
NC
1OUT
1IN −
1IN+
VDD
2IN+
2IN −
2OUT
1
2
15
3
14
4
13
5
12
6
11
7
10
8
9
14
2
13
3
12
4
11
5
10
6
9
7
8
4OUT
4IN −
4IN+
GND
3IN+
3IN −
3OUT
(TOP VIEW)
4OUT
4IN −
4IN+
GND
3IN +
3IN−
3OUT
3/4SHDN
16
1
VDD
2OUT
2IN −
2IN+
TLC075
PWP PACKAGE
(TOP VIEW)
4OUT
4IN−
4IN+
GND
3IN+
3IN−
3OUT
NC
NC
NC
1
TLC074
D OR N PACKAGE
TLC075
D OR N PACKAGE
(TOP VIEW)
1OUT
1IN−
1IN+
VDD
2IN+
2IN−
2OUT
NC
NC
NC
8
2
TLC073
D OR N PACKAGE
1OUT
1IN −
1IN+
GND
NC
1SHDN
NC
TLC074
PWP PACKAGE
1
TLC072
D, DGN, OR P PACKAGE
(TOP VIEW)
1OUT
1IN−
1IN+
VDD
2IN+
2IN−
2OUT
1/2SHDN
NC
NC
1
20
2
19
3
18
4
17
5
16
6
15
7
14
8
13
9
12
10
11
4OUT
4IN−
4IN+
GND
3IN+
3IN−
3OUT
3/4SHDN
NC
NC
NC − No internal connection
TYPICAL PIN 1 INDICATORS
Pin 1
Printed or
Molded Dot
Pin 1
Stripe
Pin 1
Bevel Edges
WWW.TI.COM
Pin 1
Molded ”U” Shape
3
TLC070, TLC071, TLC072, TLC073, TLC074, TLC075, TLC07xA
FAMILY OF WIDE-BANDWIDTH HIGH-OUTPUT-DRIVE SINGLE SUPPLY
OPERATIONAL AMPLIFIERS
SLOS219F − JUNE 1999 − REVISED DECEMBER 2011
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)†
Supply voltage, VDD (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 V
Differential input voltage range, VID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± VDD
Continuous total power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table
Operating free-air temperature range, TA: C suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C
I suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −40°C to 125°C
Maximum junction temperature, TJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150°C
Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C
†
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTE 1: All voltage values, except differential voltages, are with respect to GND .
DISSIPATION RATING TABLE
PACKAGE
θJC
(°C/W)
θJA
(°C/W)
TA ≤ 25°C
POWER RATING
D (8)
38.3
176
710 mW
D (14)
26.9
122.3
1022 mW
D (16)
25.7
114.7
1090 mW
DGN (8)
4.7
52.7
2.37 W
DGQ (10)
4.7
52.3
2.39 W
N (14, 16)
32
78
1600 mW
P (8)
41
104
1200 mW
PWP (20)
1.40
26.1
4.79 W
recommended operating conditions
Supply voltage
voltage, VDD
Single supply
Split supply
Common-mode input voltage, VICR
Shutdown on/off voltage level‡
Operating free-air
free air temperature
temperature, TA
‡
4
VIH
MIN
MAX
4.5
16
±2.25
±8
+0.5
VDD−0.8
2
VOL
C-suffix
I-suffix
Relative to the voltage on the GND terminal of the device.
WWW.TI.COM
0.8
0
70
−40
125
UNIT
V
V
V
°C
TLC070, TLC071, TLC072, TLC073, TLC074, TLC075, TLC07xA
FAMILY OF WIDE-BANDWIDTH HIGH-OUTPUT-DRIVE SINGLE SUPPLY
OPERATIONAL AMPLIFIERS
SLOS219F − JUNE 1999 − REVISED DECEMBER 2011
electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted)
PARAMETER
VIO
Input offset voltage
αVIO
Temperature coefficient of input
offset voltage
TEST CONDITIONS
VDD = 5 V,
V
VIC = 2.5 V,
VO = 2.5 V,
RS = 50 Ω
TLC070/1/2/3,
TLC074/5
TLC070/1/2/3A,
TLC074/5A
TA†
MIN
25°C
IIB
Input offset current
Input bias current
Common mode input voltage
Common-mode
VDD = 5 V,
V
VIC = 2.5 V,
VO = 2.5 V,
RS = 50 Ω
TLC07XC
TLC07XI
25°C
390
Full range
VIC = 2.5 V
IOH = − 35 mA
IOH = − 50 mA
IOL = 1 mA
IOL = 20 mA
VOL
Low-level output
p voltage
g
VIC = 2.5 V
0.7
IOL = 35 mA
IOL = 50 mA
†
Short circuit output current
Short-circuit
IO
Output current
50
pA
700
1.5
50
100
Full range
pA
700
25°C
0.5
to
4.2
Full range
0.5
to
4.2
25°C
4.1
Full range
3.9
25°C
3.7
Full range
3.5
25°C
3.4
Full range
3.2
25°C
3.2
−40°C to
85°C
μV
V
μV/°C
V/°C
100
V
4.3
4
V
3.8
3.6
3
25°C
0.18
Full range
25°C
25°C
0.25
0.35
0.35
Full range
0.39
0.45
0.43
0.55
0.48
0.63
Full range
25°C
IOS
1400
UNIT
2000
Full range
RS = 50 Ω
IOH = − 20 mA
High-level
g
output
p voltage
g
1900
3000
25°C
TLC07XC
IOH = − 1 mA
VOH
390
12
1.2
TLC07XI
VICR
MAX
Full range
25°C
IIO
TYP
V
0.7
−40°C to
85°C
0.7
Sourcing
25°C
100
Sinking
25°C
100
VOH = 1.5 V from positive rail
25°C
57
VOL = 0.5 V from negative rail
25°C
55
mA
mA
Full range is 0°C to 70°C for C suffix and − 40°C to 125°C for I suffix. If not specified, full range is − 40°C to 125°C.
WWW.TI.COM
5
TLC070, TLC071, TLC072, TLC073, TLC074, TLC075, TLC07xA
FAMILY OF WIDE-BANDWIDTH HIGH-OUTPUT-DRIVE SINGLE SUPPLY
OPERATIONAL AMPLIFIERS
SLOS219F − JUNE 1999 − REVISED DECEMBER 2011
electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted)
(continued)
PARAMETER
TEST CONDITIONS
AVD
Large signal differential voltage
Large-signal
amplification
ri(d)
Differential input resistance
CIC
Common-mode input
capacitance
f = 10 kHz
zo
Closed-loop output impedance
f = 10 kHz,
V
VO(PP) = 3 V,
RL = 10 kΩ
AV = 10
CMRR
Common mode rejection ratio
Common-mode
VIC = 1 to 3 V,
V
RS = 50 Ω
kSVR
Supply voltage rejection ratio
(ΔVDD /ΔVIO)
VDD = 4.5 V to 16 V,
No load
VIC = VDD /2,
IDD
Supply current (per channel)
VO = 2
2.5
5V
V,
No load
IDD(SHDN)
Supply current in shutdown
mode (per channel)
(TLC070, TLC073, TLC075)
SHDN ≤ 0.8
08V
†
6
TA†
MIN
TYP
25°C
100
120
Full range
100
UNIT
dB
25°C
1000
GΩ
25°C
22.9
pF
0.25
Ω
25°C
25°C
80
Full range
80
25°C
80
Full range
80
25°C
95
Full range
Full range is 0°C to 70°C for C suffix and − 40°C to 125°C for I suffix. If not specified, full range is − 40°C to 125°C.
dB
100
1.9
Full range
25°C
WWW.TI.COM
MAX
dB
2.5
3.5
125
200
250
mA
μA
A
TLC070, TLC071, TLC072, TLC073, TLC074, TLC075, TLC07xA
FAMILY OF WIDE-BANDWIDTH HIGH-OUTPUT-DRIVE SINGLE SUPPLY
OPERATIONAL AMPLIFIERS
SLOS219F − JUNE 1999 − REVISED DECEMBER 2011
operating characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted)
PARAMETER
SR
SR+
Positive slew rate at unity gain
VO(PP) = 0.8 V,
RL = 10 kΩ
CL = 50 pF,
SR
SR−
Negative slew rate at unity gain
VO(PP) = 0.8 V,
RL = 10 kΩ
CL = 50 pF,
Vn
Equivalent input noise voltage
In
MIN
TYP
16
25°C
10
Full range
9.5
25°C
12.5
Full range
19
10
25°C
12
f = 1 kHz
25°C
7
Equivalent input noise current
f = 1 kHz
25°C
0.6
THD + N
Total harmonic distortion plus noise
VO(PP) = 3 V,
RL = 10 kΩ and 250 Ω,
f = 1 kHz
t(on)
Amplifier turn-on time‡
t(off)
Amplifier turn-off time‡
ts
φm
Settling time
Phase margin
Gain margin
‡
TA†
f = 100 Hz
Gain-bandwidth product
†
TEST CONDITIONS
AV = 1
AV = 10
UNIT
V/ s
V/μs
V/ s
V/μs
nV/√Hz
fA /√Hz
0.002%
25°C
25
C
AV = 100
RL = 10 kΩ
MAX
0.012%
0.085%
25°C
0.15
μs
25°C
1.3
μs
25°C
10
MHz
f = 10 kHz,
RL = 10 kΩ
V(STEP)PP = 1 V,
AV = −1,
CL = 10 pF,
RL = 10 kΩ
0.1%
V(STEP)PP = 1 V,
AV = −1,
CL = 47 pF,
RL = 10 kΩ
0.1%
0.18
0.01%
0.39
RL = 10 kΩ,
CL = 50 pF
RL = 10 kΩ,
CL = 0 pF
RL = 10 kΩ,
CL = 50 pF
RL = 10 kΩ,
CL = 0 pF
0.18
0.01%
0.39
25°C
25°C
25°C
μss
32°
40°
2.2
3.3
dB
Full range is 0°C to 70°C for C suffix and − 40°C to 125°C for I suffix. If not specified, full range is − 40°C to 125°C.
Disable time and enable time are defined as the interval between application of the logic signal to SHDN and the point at which the supply current
has reached half its final value.
WWW.TI.COM
7
TLC070, TLC071, TLC072, TLC073, TLC074, TLC075, TLC07xA
FAMILY OF WIDE-BANDWIDTH HIGH-OUTPUT-DRIVE SINGLE SUPPLY
OPERATIONAL AMPLIFIERS
SLOS219F − JUNE 1999 − REVISED DECEMBER 2011
electrical characteristics at specified free-air temperature, VDD = 12 V (unless otherwise noted)
PARAMETER
VIO
Input offset voltage
αVIO
Temperature coefficient of input
offset voltage
TEST CONDITIONS
VDD = 12 V
VIC = 6 V,
VO = 6 V,
RS = 50 Ω
TLC070/1/2/3,
TLC074/5
TLC070/1/2/3A,
TLC074/5A
TA†
MIN
25°C
IIB
Input offset current
Input bias current
Common mode input voltage
Common-mode
VDD = 12 V
VIC = 6 V,
VO = 6 V,
RS = 50 Ω
TLC07xC
TLC07xI
25°C
390
Full range
VIC = 6 V
IOH = − 35 mA
IOH = − 50 mA
IOL = 1 mA
IOL = 20 mA
VOL
Low-level output
p voltage
g
VIC = 6 V
0.7
IOL = 35 mA
IOL = 50 mA
Short circuit output current
Short-circuit
IO
Output current
†
8
1.5
pA
50
100
pA
700
25°C
0.5
to
11.2
Full range
0.5
to
11.2
25°C
11.1
V
11.2
11
25°C
10.8
Full range
10.7
25°C
10.6
Full range
10.3
25°C
10.4
−40°C to
85°C
10.3
25°C
10.9
10.5
0.17
Full range
25°C
0.35
0.45
0.4
0.52
0.5
Full range
V
0.6
0.45
−40°C to
85°C
0.6
0.65
Sourcing
25°C
150
25°C
150
VOH = 1.5 V from positive rail
25°C
57
VOL = 0.5 V from negative rail
25°C
55
Full range is 0°C to 70°C for C suffix and − 40°C to 125°C for I suffix. If not specified, full range is − 40°C to 125°C.
0.25
0.35
Full range
25°C
V
10.7
Sinking
WWW.TI.COM
50
700
Full range
Full range
μV
V
μV/°C
V/°C
100
25°C
IOS
1400
UNIT
2000
Full range
RS = 50 Ω
IOH = − 20 mA
High-level
g
output
p voltage
g
1900
3000
25°C
TLC07xC
IOH = − 1 mA
VOH
390
12
1.2
TLC07xI
VICR
MAX
Full range
25°C
IIO
TYP
mA
mA
TLC070, TLC071, TLC072, TLC073, TLC074, TLC075, TLC07xA
FAMILY OF WIDE-BANDWIDTH HIGH-OUTPUT-DRIVE SINGLE SUPPLY
OPERATIONAL AMPLIFIERS
SLOS219F − JUNE 1999 − REVISED DECEMBER 2011
electrical characteristics at specified free-air temperature, VDD = 12 V (unless otherwise noted)
(continued)
PARAMETER
†
TEST CONDITIONS
AVD
Large signal differential voltage
Large-signal
amplification
ri(d)
Differential input resistance
CIC
Common-mode input
capacitance
f = 10 kHz
zo
Closed-loop output impedance
f = 10 kHz,
V
VO(PP) = 8 V,
RL = 10 kΩ
AV = 10
CMRR
Common mode rejection ratio
Common-mode
VIC = 1 to 10 V,
V
RS = 50 Ω
kSVR
Supply voltage rejection ratio
(ΔVDD /ΔVIO)
VDD = 4.5 V to 16 V,
No load
VIC = VDD /2,
IDD
Supply current (per channel)
VO = 7
7.5
5V
V,
No load
IDD(SHDN)
Supply current in shutdown
mode (TLC070,
(TLC070 TLC073
TLC073,
TLC075) (per channel)
SHDN ≤ 0.8
08V
TA†
MIN
TYP
25°C
120
140
Full range
120
MAX
UNIT
dB
25°C
1000
GΩ
25°C
21.6
pF
0.25
Ω
25°C
25°C
80
Full range
80
25°C
80
Full range
80
25°C
100
100
2.1
Full range
25°C
Full range
dB
dB
2.9
3.5
125
200
250
mA
μA
A
Full range is 0°C to 70°C for C suffix and − 40°C to 125°C for I suffix. If not specified, full range is − 40°C to 125°C.
WWW.TI.COM
9
TLC070, TLC071, TLC072, TLC073, TLC074, TLC075, TLC07xA
FAMILY OF WIDE-BANDWIDTH HIGH-OUTPUT-DRIVE SINGLE SUPPLY
OPERATIONAL AMPLIFIERS
SLOS219F − JUNE 1999 − REVISED DECEMBER 2011
operating characteristics at specified free-air temperature, VDD = 12 V (unless otherwise noted)
PARAMETER
SR
SR+
Positive slew rate at unity gain
VO(PP) = 2 V,
RL = 10 kΩ
CL = 50 pF,
SR
SR−
Negative slew rate at unity gain
VO(PP) = 2 V,
RL = 10 kΩ
CL = 50 pF,
Vn
Equivalent input noise voltage
In
MIN
TYP
16
25°C
10
Full range
9.5
25°C
12.5
Full range
19
10
25°C
12
f = 1 kHz
25°C
7
Equivalent input noise current
f = 1 kHz
25°C
0.6
THD + N
Total harmonic distortion plus noise
VO(PP) = 8 V,
RL = 10 kΩ and 250 Ω,
f = 1 kHz
t(on)
Amplifier turn-on time‡
t(off)
Amplifier turn-off time‡
ts
φm
Settling time
Phase margin
Gain margin
‡
TA†
f = 100 Hz
Gain-bandwidth product
†
TEST CONDITIONS
AV = 1
AV = 10
UNIT
V/ s
V/μs
V/ s
V/μs
nV/√Hz
fA /√Hz
0.002%
25°C
25
C
AV = 100
RL = 10 kΩ
MAX
0.005%
0.022%
25°C
0.47
μs
25°C
2.5
μs
25°C
10
MHz
f = 10 kHz,
RL = 10 kΩ
V(STEP)PP = 1 V,
AV = −1,
CL = 10 pF,
RL = 10 kΩ
0.1%
V(STEP)PP = 1 V,
AV = −1,
CL = 47 pF,
RL = 10 kΩ
0.1%
0.17
0.01%
0.29
RL = 10 kΩ,
CL = 50 pF
RL = 10 kΩ,
CL = 0 pF
RL = 10 kΩ,
CL = 50 pF
RL = 10 kΩ,
CL = 0 pF
0.17
0.01%
0.22
25°C
25°C
25°C
μss
37°
42°
3.1
4
dB
Full range is 0°C to 70°C for C suffix and − 40°C to 125°C for I suffix. If not specified, full range is − 40°C to 125°C.
Disable time and enable time are defined as the interval between application of the logic signal to SHDN and the point at which the supply current
has reached half its final value.
10
WWW.TI.COM
TLC070, TLC071, TLC072, TLC073, TLC074, TLC075, TLC07xA
FAMILY OF WIDE-BANDWIDTH HIGH-OUTPUT-DRIVE SINGLE SUPPLY
OPERATIONAL AMPLIFIERS
SLOS219F − JUNE 1999 − REVISED DECEMBER 2011
TYPICAL CHARACTERISTICS
Table of Graphs
FIGURE
VIO
Input offset voltage
vs Common-mode input voltage
1, 2
IIO
Input offset current
vs Free-air temperature
3, 4
IIB
Input bias current
vs Free-air temperature
3, 4
VOH
High-level output voltage
vs High-level output current
5, 7
VOL
Low-level output voltage
vs Low-level output current
6, 8
Zo
Output impedance
vs Frequency
9
IDD
Supply current
vs Supply voltage
10
PSRR
Power supply rejection ratio
vs Frequency
11
CMRR
Common-mode rejection ratio
vs Frequency
12
Vn
Equivalent input noise voltage
vs Frequency
13
VO(PP)
Peak-to-peak output voltage
vs Frequency
14, 15
Crosstalk
vs Frequency
16
Differential voltage gain
vs Frequency
17, 18
Phase
vs Frequency
17, 18
Phase margin
vs Load capacitance
19, 20
Gain margin
vs Load capacitance
21, 22
Gain-bandwidth product
vs Supply voltage
SR
Slew rate
vs Supply voltage
vs Free-air temperature
24
25, 26
THD + N
Total harmonic distortion plus noise
vs Frequency
27, 28
vs Peak-to-peak output voltage
29, 30
φm
23
Large-signal follower pulse response
31, 32
Small-signal follower pulse response
33
Large-signal inverting pulse response
34, 35
Small-signal inverting pulse response
36
Shutdown forward isolation
vs Frequency
37, 38
Shutdown reverse isolation
vs Frequency
39, 40
vs Supply voltage
Shutdown supply current
vs Free-air temperature
Shutdown pulse
41
42
43, 44
WWW.TI.COM
11
TLC070, TLC071, TLC072, TLC073, TLC074, TLC075, TLC07xA
FAMILY OF WIDE-BANDWIDTH HIGH-OUTPUT-DRIVE SINGLE SUPPLY
OPERATIONAL AMPLIFIERS
SLOS219F − JUNE 1999 − REVISED DECEMBER 2011
TYPICAL CHARACTERISTICS
INPUT OFFSET VOLTAGE
vs
COMMON-MODE INPUT VOLTAGE
250
150
125
100
75
50
25
−50
−75
−100
−125
−150
−175
−200
−225
−250
−25
0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0
−275
0
VICR − Common-Mode Input Voltage − V
−20
−40
−60
−80
−100
IIB
−120
VDD = 12 V
−140
6
7
8
9 10 11 12
4.5
TA = 70°C
TA = 25°C
4.0
TA = −40°C
3.5
TA = 125°C
3.0
2.5
TA = 25°C
10.0
9.5
VDD = 12 V
9.0
5 10 15 20 25 30 35 40 45 50
IOH - High-Level Output Current - mA
Figure 7
LOW-LEVEL OUTPUT VOLTAGE
vs
LOW-LEVEL OUTPUT CURRENT
VDD = 5 V
0.9
0.8
0.7
0.6
TA = 70°C
TA = 25°C
0.5
0.4
TA = 125°C
0.3
TA = −40°C
0.2
0.1
0
10 15 20 25 30 35 40 45 50
IOH - High-Level Output Current - mA
5 10 15 20 25 30 35 40 45 50
IOL - Low-Level Output Current - mA
Figure 6
OUTPUT IMPEDANCE
vs
FREQUENCY
1000
0.9
0.8
TA = 125°C
0.7
TA = 70°C
0.6
TA = 25°C
0.5
0.4
0.3
TA = −40°C
0.2
0.1
100
10
1
0.10
VDD = 5 V and 12 V
TA = 25°C
AV = 100
AV = 10
AV = 1
VDD = 12 V
0.0
0
Figure 3
LOW-LEVEL OUTPUT VOLTAGE
vs
LOW-LEVEL OUTPUT CURRENT
VOL − Low-Level Output Voltage − V
TA = −40°C
−120
−55 −40 −25 −10 5 20 35 50 65 80 95 110 125
5
1.0
10.5
−100
Figure 5
12.0
11.0
IIB
VDD = 5V
0.0
0
HIGH-LEVEL OUTPUT VOLTAGE
vs
HIGH-LEVEL OUTPUT CURRENT
11.5
−80
TA − Free−Air Temperature − °C
2.0
−160
−55 −40 −25 −10 5 20 35 50 65 80 95 110 125
TA = 125°C
TA = 70°C
−60
1.0
VDD = 5 V
Figure 4
V OH − High-Level Output Voltage − V
5
−40
5.0
TA − Free-Air Temperature − °C
12
4
−20
HIGH-LEVEL OUTPUT VOLTAGE
vs
HIGH-LEVEL OUTPUT CURRENT
V OH − High-Level Output Voltage − V
IIO
3
IIO
Figure 2
INPUT BIAS CURRENT AND
INPUT OFFSET CURRENT
vs
FREE-AIR TEMPERATURE
0
2
0
VICR − Common-Mode Input Voltage − V
Figure 1
20
1
20
VOL − Low-Level Output Voltage − V
175
0
I IB / I IO − Input Bias and Input Offset Current − pA
VDD = 12 V
TA = 25° C
Z o − Output Impedance − Ω
VDD = 5 V
TA = 25° C
200
0
−25
V IO − Input Offset Voltage − μ V
V IO − Input Offset Voltage − μ V
225
INPUT BIAS CURRENT AND
INPUT OFFSET CURRENT
vs
FREE-AIR TEMPERATURE
I IB / I IO − Input Bias and Input Offset Current − pA
INPUT OFFSET VOLTAGE
vs
COMMON-MODE INPUT VOLTAGE
0
5 10 15 20 25 30 35 40 45 50
IOL - Low-Level Output Current - mA
Figure 8
WWW.TI.COM
0.01
100
1k
10k
100k
f - Frequency - Hz
Figure 9
1M
10M
TLC070, TLC071, TLC072, TLC073, TLC074, TLC075, TLC07xA
FAMILY OF WIDE-BANDWIDTH HIGH-OUTPUT-DRIVE SINGLE SUPPLY
OPERATIONAL AMPLIFIERS
SLOS219F − JUNE 1999 − REVISED DECEMBER 2011
TYPICAL CHARACTERISTICS
SUPPLY CURRENT
vs
SUPPLY VOLTAGE
2.0
TA = 125°C
TA = 70°C
1.0
AV = 1
SHDN = VDD
Per Channel
0.5
0.0
4
5
6
120
VDD = 12 V
100
80
60
40
VDD = 5 V
20
0
7 8 9 10 11 12 13 14 15 16
VDD − Supply Voltage - V
0
10
V O(PP) − Peak-to-Peak Output Voltage − V
25
20
15
10
VDD = 5 V
5
0
10
100
1k
10k
100k
1M
10M
100
80
60
40
20
0
100
10k
100k
f - Frequency - Hz
PEAK-TO-PEAK OUTPUT
VOLTAGE
vs
FREQUENCY
PEAK-TO-PEAK OUTPUT
VOLTAGE
vs
FREQUENCY
VDD = 12 V
10
8
6
VDD = 5 V
4
THD+N < = 5%
RL = 600 Ω
TA = 25°C
2
0
100k
1M
f - Frequency - Hz
f − Frequency − Hz
Figure 13
1k
1M
10M
Figure 12
12
10k
10M
Figure 14
12
10
VDD = 12 V
8
6
4
2
0
10k
VDD = 5 V
THD+N < = 5%
RL = 10 kΩ
TA = 25°C
100k
1M
f - Frequency - Hz
10M
Figure 15
CROSSTALK
vs
FREQUENCY
0
−20
−40
Crosstalk − dB
Hz
V n − Equivalent Input Noise Voltage − nV/
40
30
100k
VDD = 5 V and 12 V
TA = 25°C
120
Figure 11
EQUIVALENT INPUT NOISE VOLTAGE
vs
FREQUENCY
35
10k
140
f − Frequency − Hz
Figure 10
VDD = 12 V
1k
100
CMRR − Common-Mode Rejection Ratio − dB
TA = −40°C
V O(PP) − Peak-to-Peak Output Voltage − V
I DD − Supply Current − mA
TA = 25°C
1.5
140
PSRR − Power Supply Rejection Ratio − dB
3.0
2.5
COMMON-MODE REJECTION RATIO
vs
FREQUENCY
POWER SUPPLY REJECTION RATIO
vs
FREQUENCY
VDD = 5 V and 12 V
AV = 1
RL = 10 kΩ
VI(PP) = 2 V
For All Channels
−60
−80
−100
−120
−140
−160
10
100
1k
10k
100k
f − Frequency − Hz
Figure 16
WWW.TI.COM
13
TLC070, TLC071, TLC072, TLC073, TLC074, TLC075, TLC07xA
FAMILY OF WIDE-BANDWIDTH HIGH-OUTPUT-DRIVE SINGLE SUPPLY
OPERATIONAL AMPLIFIERS
SLOS219F − JUNE 1999 − REVISED DECEMBER 2011
TYPICAL CHARACTERISTICS
DIFFERENTIAL VOLTAGE GAIN AND
PHASE
vs
FREQUENCY
DIFFERENTIAL VOLTAGE GAIN AND
PHASE
vs
FREQUENCY
70
70
80
Gain
−45
50
Phase
40
−90
30
20
−135
10
0
−10
−20
1k
VDD = ±2.5 V
RL = 10 kΩ
CL = 0 pF
TA = 25°C
10k
100k
−180
1M
Gain
60
Phase
40
20
−135
10
0
−10
VDD = ±6 V
RL = 10 kΩ
CL = 0 pF
TA = 25°C
10k
PHASE MARGIN
vs
LOAD CAPACITANCE
40°
25°
Rnull = 50 Ω
Rnull = 20 Ω
VDD = 5 V
RL = 10 kΩ
TA = 25°C
30°
Rnull = 100 Ω
25°
Rnull = 20 Ω
15°
VDD = 12 V
RL = 10 kΩ
TA = 25°C
10°
5°
0°
10
100
GAIN MARGIN
vs
LOAD CAPACITANCE
φ m − Phase Margin − dB
Rnull = 100 Ω
3
Rnull = 50 Ω
2
Rnull = 20 Ω
1.5
1
0.5
VDD = 12 V
RL = 10 kΩ
TA = 25°C
0
10
100
CL − Load Capacitance − pF
Figure 22
14
VDD = 5 V
RL = 10 kΩ
TA = 25°C
Rnull = 20 Ω
100
CL − Load Capacitance − pF
Figure 21
SLEW RATE
vs
SUPPLY VOLTAGE
10.0
3.5
2.5
1
GAIN BANDWIDTH PRODUCT
vs
SUPPLY VOLTAGE
Rnull = 0 Ω
4
Rnull = 50 Ω
1.5
Figure 20
GBWP - Gain Bandwidth Product - MHz
5
2
CL − Load Capacitance − pF
Figure 19
4.5
2.5
0
10
100
CL − Load Capacitance − pF
Rnull = 100 Ω
3
0.5
22
CL = 11 pF
9.9
9.8
9.7
20
RL = 10 kΩ
9.6
9.5
9.4
RL = 600 Ω
9.3
RL = 600 Ω and 10 kΩ
CL = 50 pF
AV = 1
21
TA = 25°C
9.2
9.1
SR − Slew Rate − V/ μ s
0°
10
Rnull = 50 Ω
20°
Rnull = 0 Ω
3.5
G − Gain Margin − dB
φ m − Phase Margin
φ m − Phase Margin
4
Rnull = 0 Ω
35°
5°
−225
100M
GAIN MARGIN
vs
LOAD CAPACITANCE
45°
30°
10°
10M
Figure 18
Rnull = 0 Ω
Rnull = 100 Ω
15°
1M
f − Frequency − Hz
PHASE MARGIN
vs
LOAD CAPACITANCE
20°
−180
100k
Figure 17
35°
−90
30
f − Frequency − Hz
40°
−45
50
−20
1k
−225
100M
10M
0
Phase − °
60
A VD − Different Voltage Gain − dB
0
Phase − °
A VD − Different Voltage Gain − dB
80
19
Slew Rate −
18
17
16
Slew Rate +
15
14
13
9.0
12
4
5
6
7 8 9 10 11 12 13 14 15 16
VDD - Supply Voltage - V
Figure 23
WWW.TI.COM
4
5
6
7 8 9 10 11 12 13 14 15 16
VDD - Supply Voltage - V
Figure 24
TLC070, TLC071, TLC072, TLC073, TLC074, TLC075, TLC07xA
FAMILY OF WIDE-BANDWIDTH HIGH-OUTPUT-DRIVE SINGLE SUPPLY
OPERATIONAL AMPLIFIERS
SLOS219F − JUNE 1999 − REVISED DECEMBER 2011
TYPICAL CHARACTERISTICS
SLEW RATE
vs
FREE-AIR TEMPERATURE
10
5
0
−55 −35 −15 5 25 45 65 85 105 125
TA - Free-Air Temperature - °C
0.01
AV = 10
AV = 1
100k
f − Frequency − Hz
RL = 10 kΩ
0.001
0.0001
0.25
AV = 1
0.001
100
0.75
1.25 1.75 2.25
2.75
3.25 3.75
VDD = 5 V
RL = 600 Ω
and 10 kΩ
CL = 8 pF
TA = 25°C
1.2 1.4 1.6 1.8
t − Time − μs
Figure 31
2
100k
TOTAL HARMONIC DISTORTION
PLUS NOISE
vs
PEAK-TO-PEAK OUTPUT VOLTAGE
10
VDD = 12 V
AV = 1
f = 1 kHz
1
RL = 250 Ω
0.1
RL = 600 Ω
0.01
0.001
RL = 10 kΩ
0.0001
0.5
2.5
4.5
6.5
8.5
10.5
VO(PP) − Peak-to-Peak Output Voltage − V
Figure 29
Figure 30
LARGE SIGNAL FOLLOWER
PULSE RESPONSE
SMALL SIGNAL FOLLOWER PULSE
RESPONSE
VI(100mV/Div)
VO (2 V/Div)
VDD = 12 V
RL = 600 Ω
and 10 kΩ
CL = 8 pF
TA = 25°C
0
10k
Figure 27
VI (5 V/Div)
VO (500 mV/Div)
1k
f − Frequency − Hz
VO(PP) − Peak-to-Peak Output Voltage − V
V O − Output Voltage − V
V O − Output Voltage − V
RL = 600 Ω
0.01
VI (1 V/Div)
1
RL = 250 Ω
0.1
LARGE SIGNAL FOLLOWER
PULSE RESPONSE
0.2 0.4 0.6 0.8
VDD = 5 V
AV = 1
f = 1 kHz
1
Figure 28
0
VDD = 12 V
RL = 600 Ω and 10 kΩ
CL = 50 pF
AV = 1
AV = 10
0.01
TOTAL HARMONIC DISTORTION
PLUS NOISE
vs
PEAK-TO-PEAK OUTPUT VOLTAGE
Total Harmonic Distortion + Noise − %
Total Harmonic Distortion + Noise − %
AV = 100
10k
5
10
VDD = 12 V
RL = 10 kΩ
VO(PP) = 12 V
1k
10
VDD = 5 V
RL = 10 kΩ
VO(PP) = 2 V
AV = 100
0.1
Figure 26
TOTAL HARMONIC DISTORTION
PLUS NOISE
vs
FREQUENCY
0.001
100
Slew Rate +
0
−55 −35 −15 5 25 45 65 85 105 125
TA - Free-Air Temperature - °C
Figure 25
0.1
Total Harmonic Distortion + Noise − %
Slew Rate +
15
Total Harmonic Distortion + Noise − %
SR − Slew Rate − V/ μ s
15
Slew Rate −
20
V O − Output Voltage − V
Slew Rate −
20
1
25
VDD = 5 V
RL = 600 Ω and 10 kΩ
CL = 50 pF
AV = 1
SR − Slew Rate − V/ μ s
25
TOTAL HARMONIC DISTORTION
PLUS NOISE
vs
FREQUENCY
SLEW RATE
vs
FREE-AIR TEMPERATURE
0.2 0.4 0.6 0.8
1
1.2 1.4 1.6 1.8
t − Time − μs
Figure 32
WWW.TI.COM
2
VO(50mV/Div)
VDD = 5 V and 12 V
RL = 600 Ω and 10 kΩ
CL = 8 pF
TA = 25°C
0
0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 0.10
t − Time − μs
Figure 33
15
TLC070, TLC071, TLC072, TLC073, TLC074, TLC075, TLC07xA
FAMILY OF WIDE-BANDWIDTH HIGH-OUTPUT-DRIVE SINGLE SUPPLY
OPERATIONAL AMPLIFIERS
SLOS219F − JUNE 1999 − REVISED DECEMBER 2011
TYPICAL CHARACTERISTICS
LARGE SIGNAL INVERTING
PULSE RESPONSE
LARGE SIGNAL INVERTING
PULSE RESPONSE
VI (5 V/div)
VDD = 5 V
RL = 600 Ω
and 10 kΩ
CL = 8 pF
TA = 25°C
VI (100 mV/div)
V O − Output Voltage − V
V O − Output Voltage − V
VI (2 V/div)
V O − Output Voltage − V
SMALL SIGNAL INVERTING
PULSE RESPONSE
VDD = 12 V
RL = 600 Ω
and 10 kΩ
CL = 8 pF
TA = 25°C
VDD = 5 & 12 V
RL = 600 Ω and 10 kΩ
CL = 8 pF
TA = 25°C
VO (50 mV/Div)
VO (2 V/Div)
VO (500 mV/Div)
0.2 0.4 0.6 0.8
1
1.2 1.4 1.6 1.8
0
2
0.2 0.4 0.6 0.8
Figure 36
SHUTDOWN FORWARD
ISOLATION
vs
FREQUENCY
100
RL = 600 Ω
80
60
RL = 10 kΩ
40
140
VDD = 12 V
CL= 0 pF
TA = 25°C
VI(PP) = 0.1, 8, and 12 V
120
100
80
Sutdown Reverse Isolation - dB
Sutdown Forward Isolation - dB
Sutdown Forward Isolation - dB
120
RL = 600 Ω
60
RL = 10 kΩ
40
20
10k 100k 1M
f - Frequency - Hz
10M
100M
I DD(SHDN) − Shutdown Supply Current - μ A
80
RL = 600 Ω
60
RL = 10 kΩ
40
20
1k
10k 100k 1M
f - Frequency - Hz
Figure 40
80
RL = 600 Ω
60
RL = 10 kΩ
40
1k
10k 100k 1M
f - Frequency - Hz
10M
100M
100
10M
100M
136
Shutdown On
RL = open
VIN = VDD/2
134
132
130
128
126
124
122
120
118
4
5
6
7 8 9 10 11 12 13 14 15 16
VDD - Supply Voltage - V
Figure 41
WWW.TI.COM
1k
10k 100k 1M
f - Frequency - Hz
10M
100M
Figure 39
SHUTDOWN SUPPLY CURRENT
vs
SUPPLY VOLTAGE
VDD = 12 V
CL= 0 pF
TA = 25°C
VI(PP) = 0.1, 8, and 12 V
100
100
Figure 38
140
120
VDD = 5 V
CL= 0 pF
TA = 25°C
VI(PP) = 0.1, 2.5, and 5 V
120
20
100
SHUTDOWN REVERSE
ISOLATION
vs
FREQUENCY
1
SHUTDOWN REVERSE
ISOLATION
vs
FREQUENCY
140
VDD = 5 V
CL= 0 pF
TA = 25°C
VI(PP) = 0.1, 2.5, and 5 V
1k
0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9
Figure 35
Figure 37
Sutdown Reverse Isolation - dB
0
Figure 34
20
16
2
t − Time − μs
140
100
1.2 1.4 1.6 1.8
t − Time − μs
SHUTDOWN FORWARD
ISOLATION
vs
FREQUENCY
100
1
t − Time − μs
SHUTDOWN SUPPLY CURRENT
vs
FREE-AIR TEMPERATURE
I DD(SHDN) − Shutdown Supply Current - μ A
0
180
160
AV = 1
VIN = VDD/2
140
VDD = 12 V
120
100
VDD = 5 V
80
60
−55
−25
5
35
65
95
TA - Free-Air Temperature - °C
Figure 42
125
TLC070, TLC071, TLC072, TLC073, TLC074, TLC075, TLC07xA
FAMILY OF WIDE-BANDWIDTH HIGH-OUTPUT-DRIVE SINGLE SUPPLY
OPERATIONAL AMPLIFIERS
SLOS219F − JUNE 1999 − REVISED DECEMBER 2011
TYPICAL CHARACTERISTICS
SHUTDOWN PULSE
SHUTDOWN PULSE
5.5
4
Shutdown Pulse
I DD − Supply Current − mA
5.0
4.5
4.0
2
VDD = 5 V
CL= 8 pF
TA = 25°C
3.5
3.0
2.5
0
IDD RL = 10 kΩ
2.0
1.5
−2
IDD RL = 600 Ω
1.0
6
5.5
SD Off
Shutdown Pulse - V
I DD − Supply Current − mA
6.0
6
−4
SD Off
5.0
Shutdown Pulse
4
VDD = 12 V
CL= 8 pF
TA = 25°C
2
4.5
4.0
3.5
3.0
2.5
0
IDD RL = 10 kΩ
2.0
1.5
−2
IDD RL = 600 Ω
1.0
Shutdown Pulse - V
6.0
−4
0.5
0.5
0.0
0
10
20
30 40 50
t - Time - μs
60
70
80
0.0
−6
0
10
20
30 40 50
t - Time - μs
60
70
80
−6
Figure 44
Figure 43
PARAMETER MEASUREMENT INFORMATION
Rnull
_
+
RL
CL
Figure 45
APPLICATION INFORMATION
input offset voltage null circuit
The TLC070 and TLC071 has an input offset nulling function. Refer to Figure 46 for the diagram.
N2
+
IN +
−
IN −
OUT
N1
100 kΩ
R1
VDD −
NOTE A: R1 = 5.6 kΩ for offset voltage adjustment of ±10 mV.
R1 = 20 kΩ for offset voltage adjustment of ±3 mV.
Figure 46. Input Offset Voltage Null Circuit
WWW.TI.COM
17
TLC070, TLC071, TLC072, TLC073, TLC074, TLC075, TLC07xA
FAMILY OF WIDE-BANDWIDTH HIGH-OUTPUT-DRIVE SINGLE SUPPLY
OPERATIONAL AMPLIFIERS
SLOS219F − JUNE 1999 − REVISED DECEMBER 2011
APPLICATION INFORMATION
driving a capacitive load
When the amplifier is configured in this manner, capacitive loading directly on the output will decrease the
device’s phase margin leading to high frequency ringing or oscillations. Therefore, for capacitive loads of greater
than 10 pF, it is recommended that a resistor be placed in series (RNULL) with the output of the amplifier, as
shown in Figure 47. A minimum value of 20 Ω should work well for most applications.
RF
RG
Input
RNULL
_
Output
+
CLOAD
Figure 47. Driving a Capacitive Load
offset voltage
The output offset voltage, (VOO) is the sum of the input offset voltage (VIO) and both input bias currents (IIB) times
the corresponding gains. The following schematic and formula can be used to calculate the output offset
voltage:
RF
IIB−
RG
VI
+
−
IIB+
V
OO
+V
IO
ǒ ǒ ǓǓ
1)
R
R
F
G
VO
+
RS
"I
IB)
R
S
ǒ ǒ ǓǓ
1)
R
R
F
G
"I
IB–
Figure 48. Output Offset Voltage Model
18
WWW.TI.COM
R
F
TLC070, TLC071, TLC072, TLC073, TLC074, TLC075, TLC07xA
FAMILY OF WIDE-BANDWIDTH HIGH-OUTPUT-DRIVE SINGLE SUPPLY
OPERATIONAL AMPLIFIERS
SLOS219F − JUNE 1999 − REVISED DECEMBER 2011
APPLICATION INFORMATION
high speed CMOS input amplifiers
The TLC07x is a family of high-speed low-noise CMOS input operational amplifiers that has an input
capacitance of the order of 20 pF. Any resistor used in the feedback path adds a pole in the transfer function
equivalent to the input capacitance multiplied by the combination of source resistance and feedback resistance.
For example, a gain of −10, a source resistance of 1 kΩ, and a feedback resistance of 10 kΩ add an additional
pole at approximately 8 MHz. This is more apparent with CMOS amplifiers than bipolar amplifiers due to their
greater input capacitance.
This is of little consequence on slower CMOS amplifiers, as this pole normally occurs at frequencies above their
unity-gain bandwidth. However, the TLC07x with its 10-MHz bandwidth means that this pole normally occurs
at frequencies where there is on the order of 5 dB gain left and the phase shift adds considerably.
The effect of this pole is the strongest with large feedback resistances at small closed loop gains. As the
feedback resistance is increased, the gain peaking increases at a lower frequency and the 180_ phase shift
crossover point also moves down in frequency, decreasing the phase margin.
For the TLC07x, the maximum feedback resistor recommended is 5 kΩ; larger resistances can be used but a
capacitor in parallel with the feedback resistor is recommended to counter the effects of the input capacitance
pole.
The TLC073 with a 1-V step response has an 80% overshoot with a natural frequency of 3.5 MHz when
configured as a unity gain buffer and with a 10-kΩ feedback resistor. By adding a 10-pF capacitor in parallel with
the feedback resistor, the overshoot is reduced to 40% and eliminates the natural frequency, resulting in a much
faster settling time (see Figure 49). The 10-pF capacitor was chosen for convenience only.
2
VIN
V O − Output Voltage − V
1
0
With
CF = 10 pF
1.5
−1
V I − Input Voltage − V
Load capacitance had little effect on these measurements due to the excellent output drive capability of the
TLC07x.
10 pF
10 kΩ
_
1
0.5
0
−0.5
VOUT
0 0.2 0.4 0.6 0.8
t - Time - μs
1
+
IN
VDD = ±5 V
AV = +1
RF = 10 kΩ
RL = 600 Ω
CL = 22 pF
50 Ω
600 Ω
22 pF
1.2 1.4 1.6
Figure 49. 1-V Step Response
WWW.TI.COM
19
TLC070, TLC071, TLC072, TLC073, TLC074, TLC075, TLC07xA
FAMILY OF WIDE-BANDWIDTH HIGH-OUTPUT-DRIVE SINGLE SUPPLY
OPERATIONAL AMPLIFIERS
SLOS219F − JUNE 1999 − REVISED DECEMBER 2011
APPLICATION INFORMATION
general configurations
When receiving low-level signals, limiting the bandwidth of the incoming signals into the system is often
required. The simplest way to accomplish this is to place an RC filter at the noninverting terminal of the amplifier
(see Figure 50).
RG
RF
−
VO
+
VI
R1
C1
f
V
O +
V
I
ǒ
1)
R
R
F
G
–3dB
Ǔǒ
+
1
2pR1C1
Ǔ
1
1 ) sR1C1
Figure 50. Single-Pole Low-Pass Filter
If even more attenuation is needed, a multiple pole filter is required. The Sallen-Key filter can be used for this
task. For best results, the amplifier should have a bandwidth that is 8 to 10 times the filter frequency bandwidth.
Failure to do this can result in phase shift of the amplifier.
C1
VI
R1
R2
R1 = R2 = R
C1 = C2 = C
Q = Peaking Factor
(Butterworth Q = 0.707)
+
_
f
C2
RG
RF
RG =
Figure 51. 2-Pole Low-Pass Sallen-Key Filter
20
WWW.TI.COM
–3dB
+
(
1
2pRC
RF
1
2−
Q
)
TLC070, TLC071, TLC072, TLC073, TLC074, TLC075, TLC07xA
FAMILY OF WIDE-BANDWIDTH HIGH-OUTPUT-DRIVE SINGLE SUPPLY
OPERATIONAL AMPLIFIERS
SLOS219F − JUNE 1999 − REVISED DECEMBER 2011
APPLICATION INFORMATION
shutdown function
Three members of the TLC07x family (TLC070/3/5) have a shutdown terminal (SHDN) for conserving battery
life in portable applications. When the shutdown terminal is tied low, the supply current is reduced to 125
μA/channel, the amplifier is disabled, and the outputs are placed in a high-impedance mode. To enable the
amplifier, the shutdown terminal can either be left floating or pulled high. When the shutdown terminal is left
floating, care should be taken to ensure that parasitic leakage current at the shutdown terminal does not
inadvertently place the operational amplifier into shutdown. The shutdown terminal threshold is always
referenced to the voltage on the GND terminal of the device. Therefore, when operating the device with split
supply voltages (e.g. ± 2.5 V), the shutdown terminal needs to be pulled to VDD− (not system ground) to disable
the operational amplifier.
The amplifier’s output with a shutdown pulse is shown in Figures 43 and 44. The amplifier is powered with a
single 5-V supply and is configured as noninverting with a gain of 5. The amplifier turn-on and turn-off times are
measured from the 50% point of the shutdown pulse to the 50% point of the output waveform. The times for the
single, dual, and quad are listed in the data tables.
Figures 37, 38, 39, and 40 show the amplifier’s forward and reverse isolation in shutdown. The operational
amplifier is configured as a voltage follower (AV = 1). The isolation performance is plotted across frequency
using 0.1 VPP, 2.5 VPP, and 5 VPP input signals at ±2.5 V supplies and 0.1 VPP, 8 VPP, and 12 VPP input signals
at ±6 V supplies.
circuit layout considerations
To achieve the levels of high performance of the TLC07x, follow proper printed-circuit board design techniques.
A general set of guidelines is given in the following.
D Ground planes − It is highly recommended that a ground plane be used on the board to provide all
components with a low inductive ground connection. However, in the areas of the amplifier inputs and
output, the ground plane can be removed to minimize the stray capacitance.
D Proper power supply decoupling − Use a 6.8-μF tantalum capacitor in parallel with a 0.1-μF ceramic
capacitor on each supply terminal. It may be possible to share the tantalum among several amplifiers
depending on the application, but a 0.1-μF ceramic capacitor should always be used on the supply terminal
of every amplifier. In addition, the 0.1-μF capacitor should be placed as close as possible to the supply
terminal. As this distance increases, the inductance in the connecting trace makes the capacitor less
effective. The designer should strive for distances of less than 0.1 inches between the device power
terminals and the ceramic capacitors.
D Sockets − Sockets can be used but are not recommended. The additional lead inductance in the socket pins
will often lead to stability problems. Surface-mount packages soldered directly to the printed-circuit board
is the best implementation.
D Short trace runs/compact part placements − Optimum high performance is achieved when stray series
inductance has been minimized. To realize this, the circuit layout should be made as compact as possible,
thereby minimizing the length of all trace runs. Particular attention should be paid to the inverting input of
the amplifier. Its length should be kept as short as possible. This will help to minimize stray capacitance at
the input of the amplifier.
D Surface-mount passive components − Using surface-mount passive components is recommended for high
performance amplifier circuits for several reasons. First, because of the extremely low lead inductance of
surface-mount components, the problem with stray series inductance is greatly reduced. Second, the small
size of surface-mount components naturally leads to a more compact layout thereby minimizing both stray
inductance and capacitance. If leaded components are used, it is recommended that the lead lengths be
kept as short as possible.
WWW.TI.COM
21
TLC070, TLC071, TLC072, TLC073, TLC074, TLC075, TLC07xA
FAMILY OF WIDE-BANDWIDTH HIGH-OUTPUT-DRIVE SINGLE SUPPLY
OPERATIONAL AMPLIFIERS
SLOS219F − JUNE 1999 − REVISED DECEMBER 2011
APPLICATION INFORMATION
general PowerPAD design considerations
The TLC07x is available in a thermally-enhanced PowerPAD family of packages. These packages are
constructed using a downset leadframe upon which the die is mounted [see Figure 52(a) and Figure 52(b)]. This
arrangement results in the lead frame being exposed as a thermal pad on the underside of the package [see
Figure 52(c)]. Because this thermal pad has direct thermal contact with the die, excellent thermal performance
can be achieved by providing a good thermal path away from the thermal pad.
The PowerPAD package allows for both assembly and thermal management in one manufacturing operation.
During the surface-mount solder operation (when the leads are being soldered), the thermal pad must be
soldered to a copper area underneath the package. Through the use of thermal paths within this copper area,
heat can be conducted away from the package into either a ground plane or other heat dissipating device.
Soldering the PowerPAD to the PCB is always required, even with applications that have low-power dissipation.
This provides the necessary thermal and mechanical connection between the lead frame die pad and the PCB.
The PowerPAD package represents a breakthrough in combining the small area and ease of assembly of
surface mount with mechanical methods of heatsinking.
DIE
Side View (a)
Thermal
Pad
DIE
End View (b)
Bottom View (c)
NOTE A: The thermal pad is electrically isolated from all terminals in the package.
Figure 52. Views of Thermally-Enhanced DGN Package
22
WWW.TI.COM
TLC070, TLC071, TLC072, TLC073, TLC074, TLC075, TLC07xA
FAMILY OF WIDE-BANDWIDTH HIGH-OUTPUT-DRIVE SINGLE SUPPLY
OPERATIONAL AMPLIFIERS
SLOS219F − JUNE 1999 − REVISED DECEMBER 2011
APPLICATION INFORMATION
Although there are many ways to properly heatsink the PowerPAD package, the following steps illustrate the
recommended approach.
general PowerPAD design considerations (continued)
1. The thermal pad must be connected to the same voltage potential as the GND pin.
2. Prepare the PCB with a top side etch pattern as illustrated in the thermal land pattern mechanical drawing
at the end of this document. There should be etch for the leads as well as etch for the thermal pad.
3. Place five holes (single and dual) or nine holes (quad) in the area of the thermal pad. These holes should
be 13 mils in diameter. Keep them small so that solder wicking through the holes is not a problem during
reflow.
4. Additional vias may be placed anywhere along the thermal plane outside of the thermal pad area. This helps
dissipate the heat generated by the TLC07x IC. These additional vias may be larger than the 13-mil
diameter vias directly under the thermal pad. They can be larger because they are not in the thermal pad
area to be soldered so that wicking is not a problem.
5. Connect all holes to the internal ground plane that is the same potential as the device GND pin.
6. When connecting these holes to the ground plane, do not use the typical web or spoke via connection
methodology. Web connections have a high thermal resistance connection that is useful for slowing the heat
transfer during soldering operations. This makes the soldering of vias that have plane connections easier.
In this application, however, low thermal resistance is desired for the most efficient heat transfer. Therefore,
the holes under the TLC07x PowerPAD package should make their connection to the internal ground plane
with a complete connection around the entire circumference of the plated-through hole.
7. The top-side solder mask should leave the terminals of the package and the thermal pad area with its five
holes (dual) or nine holes (quad) exposed. The bottom-side solder mask should cover the five or nine holes
of the thermal pad area. This prevents solder from being pulled away from the thermal pad area during the
reflow process.
8. Apply solder paste to the exposed thermal pad area and all of the IC terminals.
9. With these preparatory steps in place, the TLC07x IC is simply placed in position and run through the solder
reflow operation as any standard surface-mount component. This results in a part that is properly installed.
For a given θJA, the maximum power dissipation is shown in Figure 54 and is calculated by the following formula:
P
Where:
D
PD
TMAX
TA
θJA
+
ǒ
T
Ǔ
–T
MAX A
q
JA
= Maximum power dissipation of TLC07x IC (watts)
= Absolute maximum junction temperature (150°C)
= Free-ambient air temperature (°C)
= θJC + θCA
θJC = Thermal coefficient from junction to case
θCA = Thermal coefficient from case to ambient air (°C/W)
WWW.TI.COM
23
TLC070, TLC071, TLC072, TLC073, TLC074, TLC075, TLC07xA
FAMILY OF WIDE-BANDWIDTH HIGH-OUTPUT-DRIVE SINGLE SUPPLY
OPERATIONAL AMPLIFIERS
SLOS219F − JUNE 1999 − REVISED DECEMBER 2011
APPLICATION INFORMATION
general PowerPAD design considerations (continued)
MAXIMUM POWER DISSIPATION
vs
FREE-AIR TEMPERATURE
Maximum Power Dissipation − W
7
6
5
4
3
2
PWP Package
Low-K Test PCB
θJA = 29.7°C/W
DGN Package
Low-K Test PCB
θJA = 52.3°C/W
TJ = 150°C
SOT-23 Package
Low-K Test PCB
θJA = 324°C/W
SOIC Package
Low-K Test PCB
θJA = 176°C/W
PDIP Package
Low-K Test PCB
θJA = 104°C/W
1
0
−55 −40 −25 −10 5 20 35 50 65 80 95 110 125
TA − Free-Air Temperature − °C
NOTE A: Results are with no air flow and using JEDEC Standard Low-K test PCB.
Figure 53. Maximum Power Dissipation vs Free-Air Temperature
The next consideration is the package constraints. The two sources of heat within an amplifier are quiescent
power and output power. The designer should never forget about the quiescent heat generated within the
device, especially multi-amplifier devices. Because these devices have linear output stages (Class A-B), most
of the heat dissipation is at low output voltages with high output currents.
The other key factor when dealing with power dissipation is how the devices are mounted on the PCB. The
PowerPAD devices are extremely useful for heat dissipation. But, the device should always be soldered to a
copper plane to fully use the heat dissipation properties of the PowerPAD. The SOIC package, on the other
hand, is highly dependent on how it is mounted on the PCB. As more trace and copper area is placed around
the device, θJA decreases and the heat dissipation capability increases. The currents and voltages shown in
these graphs are for the total package. For the dual or quad amplifier packages, the sum of the RMS output
currents and voltages should be used to choose the proper package.
24
WWW.TI.COM
TLC070, TLC071, TLC072, TLC073, TLC074, TLC075, TLC07xA
FAMILY OF WIDE-BANDWIDTH HIGH-OUTPUT-DRIVE SINGLE SUPPLY
OPERATIONAL AMPLIFIERS
SLOS219F − JUNE 1999 − REVISED DECEMBER 2011
APPLICATION INFORMATION
macromodel information
Macromodel information provided was derived using Microsim Parts™, the model generation software used
with Microsim PSpice™. The Boyle macromodel (see Note 1) and subcircuit in Figure 55 are generated using
the TLC07x typical electrical and operating characteristics at TA = 25°C. Using this information, output
simulations of the following key parameters can be generated to a tolerance of 20% (in most cases):
D
D
D
D
D
D
Maximum positive output voltage swing
Maximum negative output voltage swing
Slew rate
Quiescent power dissipation
Input bias current
Open-loop voltage amplification
D
D
D
D
D
D
Unity-gain frequency
Common-mode rejection ratio
Phase margin
DC output resistance
AC output resistance
Short-circuit output current limit
NOTE 2: G. R. Boyle, B. M. Cohn, D. O. Pederson, and J. E. Solomon, “Macromodeling of Integrated Circuit Operational Amplifiers,” IEEE Journal
of Solid-State Circuits, SC-9, 353 (1974).
PSpice and Parts are trademarks of MicroSim Corporation.
WWW.TI.COM
25
TLC070, TLC071, TLC072, TLC073, TLC074, TLC075, TLC07xA
FAMILY OF WIDE-BANDWIDTH HIGH-OUTPUT-DRIVE SINGLE SUPPLY
OPERATIONAL AMPLIFIERS
SLOS219F − JUNE 1999 − REVISED DECEMBER 2011
APPLICATION INFORMATION
99
3
VDD +
9
RSS
IN −
DP
IN +
1
C1
VDD −
C2
6
−
VE
−
−
−
+
+
GA
GCM
VLIM
−
RO1
DE
5
+
OUT
*DEVICE=TLC07X_5V, OPAMP, PJF, INT
* TLC07X − 5V operational amplifier ”macromodel” subcircuit
* created using Parts release 8.0 on 12/16/99 at 08:38
* Parts is a MicroSim product.
*
* connections:
non-inverting input
*
inverting input
*
positive power supply
*
negative power supply
*
output
*
.subckt TLC07X_5V 1 2 3 4 5
*
c1
11 12 4.8697E−12
c2
6 7 8.0000E−12
css
10 99 4.0063E−12
dc
5 53 dy
de
54 5 dy
dlp
90 91 dx
dln
92 90 dx
dp
4 3 dx
egnd 99 0 poly(2) (3,0) (4,0) 0 .5 .5
fb
7 99 poly(5) vb vc ve vlp vln 0 6.9132E6 −1E3 1E3
6E6 −6E6
ga
gcm
iss
ioff
hlim
j1
j2
r2
rd1
rd2
ro1
ro2
rp
rss
vb
vc
ve
vlim
vlp
vln
.model
.model
.model
.model
.ends
6
0
3
0
90
11
12
6
4
4
8
7
3
10
9
3
54
7
91
0
dx
dy
jx1
jx2
0 11 12 457.42E−6
6 10 99 1.1293E−6
10 dc 183.67E−6
6 dc .806E−6
0 vlim 1K
2 10 jx1
1 10 jx2
9
100.00E3
11
2.1862E3
12
2.1862E3
5 10
99 10
4
2.4728E3
99
1.0889E6
0 dc 0
53 dc 1.5410
4 dc .84403
8 dc 0
0 dc 119
92 dc 119
D(Is=800.00E−18)
D(Is=800.00E−18 Rs=1m Cjo=10p)
PJF(Is=117.50E−15 Beta=1.1391E−3 Vto=−1)
PJF(Is=117.50E−15 Beta=1.1391E−3 Vto=−1)
Figure 54. Boyle Macromodel and Subcircuit
26
+ DLP
91
+
VLP
7
8
54
4
HLIM
RD2
60
+
−
R2
−
53
DC
12
RD1
VAD
VC
90
RO2
−
+
J2
11
92
FB
VB
10
J1
−
+
ISS
RP
2
DLN
EGND +
WWW.TI.COM
VLN
PACKAGE OPTION ADDENDUM
www.ti.com
14-Oct-2022
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
(2)
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
Samples
(4/5)
(6)
TLC070AIP
ACTIVE
PDIP
P
8
50
RoHS & Green
NIPDAU
N / A for Pkg Type
-40 to 125
TLC070AI
Samples
TLC070CD
ACTIVE
SOIC
D
8
75
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
0 to 70
C070C
Samples
TLC070CDR
ACTIVE
SOIC
D
8
2500
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
0 to 70
C070C
Samples
TLC070IDR
ACTIVE
SOIC
D
8
2500
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
C070I
Samples
TLC070IP
ACTIVE
PDIP
P
8
50
RoHS & Green
NIPDAU
N / A for Pkg Type
-40 to 125
TLC070I
Samples
TLC071AID
ACTIVE
SOIC
D
8
75
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
C071AI
Samples
TLC071AIP
ACTIVE
PDIP
P
8
50
RoHS & Green
NIPDAU
N / A for Pkg Type
-40 to 125
TLC071AI
Samples
TLC071CD
ACTIVE
SOIC
D
8
75
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
0 to 70
C071C
Samples
TLC071CDG4
ACTIVE
SOIC
D
8
75
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
0 to 70
C071C
Samples
TLC071CDGN
ACTIVE
HVSSOP
DGN
8
80
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
0 to 70
ACU
Samples
TLC071CDGNR
ACTIVE
HVSSOP
DGN
8
2500
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
0 to 70
ACU
Samples
TLC071CDR
ACTIVE
SOIC
D
8
2500
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
0 to 70
C071C
Samples
TLC071CP
ACTIVE
PDIP
P
8
50
RoHS & Green
NIPDAU
N / A for Pkg Type
0 to 70
TLC071C
Samples
TLC071ID
ACTIVE
SOIC
D
8
75
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
C071I
Samples
TLC071IDGN
ACTIVE
HVSSOP
DGN
8
80
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
ACV
Samples
TLC071IDGNR
ACTIVE
HVSSOP
DGN
8
2500
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
ACV
Samples
TLC071IDR
ACTIVE
SOIC
D
8
2500
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
C071I
Samples
TLC071IP
ACTIVE
PDIP
P
8
50
RoHS & Green
NIPDAU
N / A for Pkg Type
-40 to 125
TLC071I
Samples
TLC072AID
ACTIVE
SOIC
D
8
75
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
C072AI
Samples
TLC072AIDG4
ACTIVE
SOIC
D
8
75
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
C072AI
Samples
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
14-Oct-2022
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
(2)
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
Samples
(4/5)
(6)
TLC072AIDR
ACTIVE
SOIC
D
8
2500
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
C072AI
Samples
TLC072AIP
ACTIVE
PDIP
P
8
50
RoHS & Green
NIPDAU
N / A for Pkg Type
-40 to 125
C072AI
Samples
TLC072CD
ACTIVE
SOIC
D
8
75
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
0 to 70
C072C
Samples
TLC072CDG4
ACTIVE
SOIC
D
8
75
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
0 to 70
C072C
Samples
TLC072CDGN
ACTIVE
HVSSOP
DGN
8
80
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
0 to 70
ADV
Samples
TLC072CDGNR
ACTIVE
HVSSOP
DGN
8
2500
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
0 to 70
ADV
Samples
TLC072CDGNRG4
ACTIVE
HVSSOP
DGN
8
2500
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
0 to 70
ADV
Samples
TLC072CDR
ACTIVE
SOIC
D
8
2500
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
0 to 70
C072C
Samples
TLC072CDRG4
ACTIVE
SOIC
D
8
2500
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
0 to 70
C072C
Samples
TLC072CP
ACTIVE
PDIP
P
8
50
RoHS & Green
NIPDAU
N / A for Pkg Type
0 to 70
C072C
Samples
TLC072ID
ACTIVE
SOIC
D
8
75
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
C072I
Samples
TLC072IDGN
ACTIVE
HVSSOP
DGN
8
80
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
ADW
Samples
TLC072IDGNR
ACTIVE
HVSSOP
DGN
8
2500
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
ADW
Samples
TLC072IDGNRG4
ACTIVE
HVSSOP
DGN
8
2500
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
ADW
Samples
TLC072IDR
ACTIVE
SOIC
D
8
2500
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
C072I
Samples
TLC072IP
ACTIVE
PDIP
P
8
50
RoHS & Green
NIPDAU
N / A for Pkg Type
-40 to 125
C072I
Samples
TLC073AID
ACTIVE
SOIC
D
14
50
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
CO73AI
Samples
TLC073CDGQ
ACTIVE
HVSSOP
DGQ
10
80
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
0 to 70
ADX
Samples
TLC073CDR
ACTIVE
SOIC
D
14
2500
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
0 to 70
C073C
Samples
TLC073IDGQ
ACTIVE
HVSSOP
DGQ
10
80
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
ADY
Samples
TLC073IDGQR
ACTIVE
HVSSOP
DGQ
10
2500
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
ADY
Samples
Addendum-Page 2
PACKAGE OPTION ADDENDUM
www.ti.com
14-Oct-2022
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
(2)
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
Samples
(4/5)
(6)
TLC073IN
ACTIVE
PDIP
N
14
25
RoHS & Green
NIPDAU
N / A for Pkg Type
-40 to 125
C073I
Samples
TLC074AID
ACTIVE
SOIC
D
14
50
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
TLC074AI
Samples
TLC074AIDR
ACTIVE
SOIC
D
14
2500
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
TLC074AI
Samples
TLC074AIN
ACTIVE
PDIP
N
14
25
RoHS & Green
NIPDAU
N / A for Pkg Type
-40 to 125
TLC074AI
Samples
TLC074CD
ACTIVE
SOIC
D
14
50
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
0 to 70
TLC074C
Samples
TLC074CDR
ACTIVE
SOIC
D
14
2500
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
0 to 70
TLC074C
Samples
TLC074CN
ACTIVE
PDIP
N
14
25
RoHS & Green
NIPDAU
N / A for Pkg Type
0 to 70
TLC074C
Samples
TLC074CPWP
ACTIVE
HTSSOP
PWP
20
70
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
0 to 70
TLC074C
Samples
TLC074CPWPR
ACTIVE
HTSSOP
PWP
20
2000
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
0 to 70
TLC074C
Samples
TLC074ID
ACTIVE
SOIC
D
14
50
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
TLC074I
Samples
TLC074IDR
ACTIVE
SOIC
D
14
2500
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
TLC074I
Samples
TLC074IN
ACTIVE
PDIP
N
14
25
RoHS & Green
NIPDAU
N / A for Pkg Type
-40 to 125
TLC074I
Samples
TLC074IPWP
ACTIVE
HTSSOP
PWP
20
70
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 125
TLC074I
Samples
TLC075AID
ACTIVE
SOIC
D
16
40
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
TLC075AI
Samples
TLC075AIDR
ACTIVE
SOIC
D
16
2500
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
TLC075AI
Samples
TLC075AIN
ACTIVE
PDIP
N
16
25
RoHS & Green
NIPDAU
N / A for Pkg Type
-40 to 125
TLC075AI
Samples
TLC075AIPWP
ACTIVE
HTSSOP
PWP
20
70
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 125
TLC075AI
Samples
TLC075CPWP
ACTIVE
HTSSOP
PWP
20
70
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
0 to 70
TLC075C
Samples
TLC075IPWP
ACTIVE
HTSSOP
PWP
20
70
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 125
TLC075I
Samples
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
Addendum-Page 3
PACKAGE OPTION ADDENDUM
www.ti.com
14-Oct-2022
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of
工商网监
湘ICP备2023018690号
