TPS2816-Q1 , TPS2817-Q1, TPS2818-Q1
TPS2819-Q1, TPS2828-Q1, TPS2829-Q1
SPRS289B – AUGUST 2005 – REVISED SEPTEMBER 2011
www.ti.com
Single-Channel High-Speed MOSFET Drivers
Check for Samples: TPS2816-Q1 , TPS2817-Q1, TPS2818-Q1, TPS2819-Q1, TPS2828-Q1, TPS2829-Q1
FEATURES
1
•
•
•
•
•
•
•
•
•
•
Qualified for Automotive Applications
Customer-Specific Configuration Control Can
Be Supported Along With Major-Change
Approval
Low-Cost Single-Channel High-Speed MOSFET
Driver
15-mA Max ICC (TPS2828, TPS2829)
25-ns Max Rise/Fall Times and 40-ns Max
Propagation Delay. . . 1-nF Load
2-A Peak Output Current
4-V to 14-V Driver Supply-Voltage Range,
Internal Regulator Extends Range to 40 V
(TPS2816, TPS2817, TPS2818, TPS2819)
5-pin SOT-23 Package
–40°C to 125°C Ambient-Temperature
Operating Range
Highly Resistant to Latch-Ups
TPS2816, TPS2817
TPS2818, TPS2819
DBV PACKAGE
(TOP VIEW)
VDD
1
GND
2
IN
3
5
VCC
4
OUT
TPS2828, TPS2829
DBV PACKAGE
(TOP VIEW)
NC
1
GND
2
IN
3
5
VCC
4
OUT
NC No internal connection
DESCRIPTION
The TPS28xx single-channel high-speed MOSFET drivers are capable of delivering peak currents of up to 2 A
into highly capacitive loads. High switching speeds (tr and tf = 14 ns typ) are obtained with the use of BiCMOS
outputs. Typical threshold switching voltages are two-thirds and one-third of VCC. The design inherently
minimizes shoot-through current.
A regulator is provided on TPS2816 through TPS2819 devices to allow operation with supply inputs between 14V
and 40V. The regulator output can be used to power other circuits, provided power dissipation does not exceed
package limitations. If the regulator is not required, VDD (the regulator input) should be connected to VCC. The
TPS2816 and TPS2817 input circuits include an active pullup circuit to eliminate the need for an external resistor
when using open-collector PWM controllers. The TPS2818 and TPS2819 are identical to the TPS2816 and
TPS2817, except that the active pullup circuit is omitted. The TPS2828 and TPS2829 are identical to the
TPS2818 and TPS2819, except that the internal voltage regulator is omitted, allowing quiescent current to drop
to less than 15 µA when the inputs are high or low.
The TPS28xx series devices are available in 5-pin SOT-23 (DBV) packages and operate over an ambient
temperature range of –40°C to 125°C.
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2005–2011, Texas Instruments Incorporated
TPS2816-Q1 , TPS2817-Q1, TPS2818-Q1
TPS2819-Q1, TPS2828-Q1, TPS2829-Q1
SPRS289B – AUGUST 2005 – REVISED SEPTEMBER 2011
www.ti.com
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
ORDERING INFORMATION
TA
PACKAGED DEVICES
FUNCTION
–40°C to 125°C
SOT-23-5 (DBV)
TOP-SIDE MARKING
Inverting driver with active pullup input
TPS2816DBV
PREVIEW
Noninverting driver with active pullup input
TPS2817DBV
PREVIEW
TPS2818DBV
PREVIEW
Inverting driver
Noninverting driver
Inverting driver, no regulator
TPS2819QDBVRQ1
PAYI
TPS2828DBV
PREVIEW
FUNCTIONAL BLOCK DIAGRAM
TPS2816, TPS2818
VDD
VREG
TPS2817, TPS2819
VCC
VDD
Active Pullup
(TPS2816 Only)
VREG
VCC
Active Pullup
(TPS2817 Only)
OUT
IN
OUT
IN
GND
GND
TPS2829
TPS2828
VCC
VCC
IN
OUT
IN
GND
OUT
GND
OUTPUT STAGE DIAGRAM
INPUT STAGE DIAGRAM
VCC
VCC
Predrive
To Drive
Stage
IN
OUT
2
Submit Documentation Feedback
Copyright © 2005–2011, Texas Instruments Incorporated
Product Folder Link(s): TPS2816-Q1 TPS2817-Q1 TPS2818-Q1 TPS2819-Q1 TPS2828-Q1 TPS2829-Q1
TPS2816-Q1 , TPS2817-Q1, TPS2818-Q1
TPS2819-Q1, TPS2828-Q1, TPS2829-Q1
SPRS289B – AUGUST 2005 – REVISED SEPTEMBER 2011
www.ti.com
ABSOLUTE MAXIMUM RATINGS (1) (2)
over operating free-air temperature range (unless otherwise noted) (2)
VALUE / UNITS
–0.3 V to 15 V
VCC
Supply voltage range
VDD
Regulator supply voltage range
VCC
VCC –0.3 V to 42 V
Input voltage range, IN
–0.3 V to VCC +0.5 V
Output voltage range (pin 4)
–0.5 V to VCC +0.5 V
Continuous regulator output current
25 mA
±100 mA
Continuous output current, OUT
Continuous total power dissipation
See Dissipation Rating Table
TJ
Operating junction temperature range
–40°C to 150°C
Tstg
Storage temperature range
–65°C to 150°C
Lead temperature 1,6 mm (1/16 in) from case for 10 s
260°C
Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating
conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
All voltages are with respect to device GND terminal.
(1)
(2)
DISSIPATION RATINGS (1)
PACKAGE
TA 3 25°C
POWER RATING
DERATING FACTOR
ABOVE TA = 25°C
TA = 70°C
POWER RATING
TA = 80°C
POWER RATING
DBV
437 mW
3.5 mW/°C
280 mW
227 mW
(1)
These dissipation ratings are based upon EIA specification JESD51-3, Low Effective Thermal Conductivity Test Board for Leaded
Surface Mount Packages, in tests conducted in a zero-airflow, wind-tunnel environment.
ESD RATINGS, TPS2819
over operating free-air temperature range (unless otherwise noted).
PARAMETER
ESD
VALUE
UNIT
Human Body Model (HBM)
2000
V
Machine Model (MM)
200
V
Charged-Device Model (CDM)
500
V
RECOMMENDED OPERATING CONDITIONS
over operating free-air temperature range (unless otherwise noted)
MIN
MAX
VDD
Regulator input voltage range, TPS2816 through TPS2819
8
40
UNIT
V
VCC
Supply voltage
4
14
V
IN
Input voltage
–0.3
VCC
ICC
Continuous regulator output current
0
20
mA
TJ
Operating junction temperature
–40
125
°C
V
TPS28xx ELECTRICAL CHARACTERISTICS
over recommended operating ambient temperature range, VCC = 10 V, VDD tied to VCC, CL = 1 nF (unless otherwise specified)
TYP (1)
MAX
VCC = 5 V
3.3
4
VCC = 10 V
6.6
7
VCC = 14 V
9.3
10
PARAMETER
TEST CONDITIONS
MIN
UNIT
INPUTS
Positive-going input threshold voltage
(1)
V
Typical values are for TA = 25°C, unless otherwise noted.
Copyright © 2005–2011, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TPS2816-Q1 TPS2817-Q1 TPS2818-Q1 TPS2819-Q1 TPS2828-Q1 TPS2829-Q1
3
TPS2816-Q1 , TPS2817-Q1, TPS2818-Q1
TPS2819-Q1, TPS2828-Q1, TPS2829-Q1
SPRS289B – AUGUST 2005 – REVISED SEPTEMBER 2011
www.ti.com
TPS28xx ELECTRICAL CHARACTERISTICS (continued)
over recommended operating ambient temperature range, VCC = 10 V, VDD tied to VCC, CL = 1 nF (unless otherwise specified)
MIN
TYP (1)
VCC = 5 V
1
1.7
VCC = 10 V
2
3.3
VCC = 14 V
2.5
4.6
PARAMETER
Negative-going input threshold voltage
TEST CONDITIONS
Input voltage hysteresis
Input current, TPS2818/19/28/29
Input current, TPS2816/17
MAX
UNIT
V
1.3
V
Input = 0 V or VCC
0.2
µA
Input = 0 V
650
Input = VCC
15
Input capacitance (2)
µA
5
10
pF
OUTPUTS
TPS2816, TPS2817,
TPS2818, TPS2828,
TPS2829
High-level output voltage
IO = –1 mA
TPS2819
TPS2816, TPS2817,
TPS2818, TPS2828,
TPS2829
IO = –100 mA
9.75
9.9
TA = 25°C
8
9.1
TA = –40°C to 125°C
7
9.1
IO = 1 mA
Low-level output voltage
IO = 100 mA
V
0.18
0.25
1
2
11.5
13
V
10
V
V
REGULATOR, TPS2816 THROUGH TPS2819
Output voltage
14 ≤ VDD ≤ 40 V, 0 ≤ IO ≤ 20 mA
Output voltage in dropout
IO = 10 mA, VDD = 10 V
10
8
SUPPLY CURRENT
TPS2816, TPS2817
Supply current into VCC
TPS2819
TPS2818
TPS2828, TPS2829
IN = high = 10 V
150
250
IN = low = 0 V
650
1000
TA = 25°C
25
50
TA = –40°C to 125°C
25
60
0.1
15
650
1000
50
150
50
150
IN = high or low,
High = 10 V,
Low = 0 V
IN = high or low,
High = 10 V, Low = 0 V
TPS2816, TPS2817
Supply current into VDD
TPS2818
TPS2819
(2)
4
VDD = 20 V,
IN = high = 10 V
or low = 0 V
IN = high = 11 V
or low = 0 V
µA
µA
Not production tested. Specified by design.
Submit Documentation Feedback
Copyright © 2005–2011, Texas Instruments Incorporated
Product Folder Link(s): TPS2816-Q1 TPS2817-Q1 TPS2818-Q1 TPS2819-Q1 TPS2828-Q1 TPS2829-Q1
TPS2816-Q1 , TPS2817-Q1, TPS2818-Q1
TPS2819-Q1, TPS2828-Q1, TPS2829-Q1
SPRS289B – AUGUST 2005 – REVISED SEPTEMBER 2011
www.ti.com
TPS28xxY ELECTRICAL CHARACTERISTICS
at TA = 25°C, VCC = 10 V, VDD tied to VCC, CL = 1 nF (unless otherwise specified)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
INPUTS
Positive-going input threshold voltage
Negative-going input threshold voltage
VCC = 5 V
3.3
VCC = 10 V
6.6
VCC = 14 V
9.3
VCC = 5 V
1.7
VCC = 10 V
3.3
VCC = 14 V
4.6
Input voltage hysteresis
Input current, TPS2818/19/28/29
Input current, TPS2816/17
V
V
1.3
V
Input = 0 V or VCC
0.2
µA
Input = 0 V
650
Input = VCC
15
Input resistance
Input capacitance
µA
1000
MΩ
5
pF
OUTPUTS
High-level outupt voltage
IO = –1 mA
9.9
IO = –100 mA
9.1
IO = 1 mA
Low-level outupt voltage
IO = 100 mA
0.18
1
V
V
REGULATOR, TPS2816 THROUGH TPS2819
Output voltage
14 ≤ VDD ≤ 40 V, 0 ≤ IO ≤ 20 mA
Output voltage in dropout
IO = 10 mA, VDD = 10 V
11.5
V
9
V
SUPPLY CURRENT
TPS2816,
TPS2817
Supply current into VCC
TPS2818,
TPS2819
TPS2828,
TPS2829
Supply current into VDD
TPS2816,
TPS2817
TPS2818,
TPS2819
Copyright © 2005–2011, Texas Instruments Incorporated
IN = high = 10 V
150
IN = low = 0 V
650
25
µA
IN = high or low, High = 10 V, Low = 0 V
0.1
650
µA
VDD = 20 V, IN = high = 10 V or low = 0 V
50
Submit Documentation Feedback
Product Folder Link(s): TPS2816-Q1 TPS2817-Q1 TPS2818-Q1 TPS2819-Q1 TPS2828-Q1 TPS2829-Q1
5
TPS2816-Q1 , TPS2817-Q1, TPS2818-Q1
TPS2819-Q1, TPS2828-Q1, TPS2829-Q1
SPRS289B – AUGUST 2005 – REVISED SEPTEMBER 2011
www.ti.com
SWITCHING CHARACTERISTICS
for all devices over recommended operating ambient temperature range, VCC = 10 V, VDD tied to VCC, CL = 1 nF (unless
otherwise specified)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
VCC = 14 V
tr
Rise time
VCC = 10 V
14
VCC = 5 V
Fall time
14
24
45
ns
50
VCC = 14 V
Propagation delay time, low-to-high-level output
ns
40
VCC = 10 V
VCC = 5 V
tPLH
30
35
VCC = 14 V
Propagation delay time, high-to-low-level output
ns
25
VCC = 10 V
VCC = 5 V
tPHL
30
35
VCC = 14 V
tf
UNIT
25
40
VCC = 10 V
24
VCC = 5 V
45
ns
50
SPACER
PARAMETER MEASUREMENT INFORMATION
50%
IN
50%
0V
tf
90%
OUT
tr
90%
50%
50%
10%
10%
tPHL
0V
tPLH
Figure 1. Typical Timing Diagram (TPS2816)
TPS2816
1
Regulator
5
10 V
0.1 mF
4.7 mF
2
3
4
Output
Input
50 Ω
+
1 nF
Figure 2. Switching-Time Test Setup
6
Submit Documentation Feedback
Copyright © 2005–2011, Texas Instruments Incorporated
Product Folder Link(s): TPS2816-Q1 TPS2817-Q1 TPS2818-Q1 TPS2819-Q1 TPS2828-Q1 TPS2829-Q1
TPS2816-Q1 , TPS2817-Q1, TPS2818-Q1
TPS2819-Q1, TPS2828-Q1, TPS2829-Q1
SPRS289B – AUGUST 2005 – REVISED SEPTEMBER 2011
www.ti.com
PARAMETER MEASUREMENT INFORMATION (continued)
TPS2816
VCC
Current
Loop
10 V
+
0-10 Vdc
OUT
0.1 mF
4.7 mF
Figure 3. Shoot-Through Current Test Setup
Copyright © 2005–2011, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TPS2816-Q1 TPS2817-Q1 TPS2818-Q1 TPS2819-Q1 TPS2828-Q1 TPS2829-Q1
7
TPS2816-Q1 , TPS2817-Q1, TPS2818-Q1
TPS2819-Q1, TPS2828-Q1, TPS2829-Q1
SPRS289B – AUGUST 2005 – REVISED SEPTEMBER 2011
www.ti.com
TYPICAL CHARACTERISTICS
Table of Graphs
FIGURE
Rise time
vs Supply voltage
Figure 4
Fall time
vs Supply voltage
Figure 5
Propagation time (L → H)
vs Supply voltage
Figure 6
Propagation time (H → L)
vs Supply voltage
Figure 7
Rise time
vs Ambient temperature
Figure 8
Fall time
vs Ambient temperature
Figure 9
Propagation time (L → H)
vs Supply voltage
Figure 10
Propagation time (H → L)
vs Ambient temperature
Figure 11
Supply current (VCC)
vs Supply voltage
Figure 12
Supply current (VCC)
vs Load capacitance
Figure 13
Supply current (VCC)
vs Ambient temperature
Figure 14
Input threshold voltage
vs Supply voltage
Figure 15
Regulator output voltage
vs Regulator supply voltage
Figure 16
Regulator quiescent current
vs Regulator supply voltage
Figure 17
Shoot-through current
vs Input voltage (L → H)
Figure 18
Shoot-through current
vs Input voltage (H → L)
Figure 19
RISE TIME
vs
SUPPLY VOLTAGE
FALL TIME
vs
SUPPLY VOLTAGE
35
30
TA = 25°C
TA = 25°C
30
25
CL = 2200 pF
CL = 2200 pF
tf - Fall Time - ns
tr - Rise Time - ns
25
20
15
CL = 1000 pF
20
15
10
CL = 1000 pF
10
5
5
CL = 0
CL = 0
0
0
4
6
12
8
10
VCC - Supply Voltage - V
Figure 4.
8
Submit Documentation Feedback
14
4
6
12
8
10
VCC - Supply Voltage - V
14
Figure 5.
Copyright © 2005–2011, Texas Instruments Incorporated
Product Folder Link(s): TPS2816-Q1 TPS2817-Q1 TPS2818-Q1 TPS2819-Q1 TPS2828-Q1 TPS2829-Q1
TPS2816-Q1 , TPS2817-Q1, TPS2818-Q1
TPS2819-Q1, TPS2828-Q1, TPS2829-Q1
SPRS289B – AUGUST 2005 – REVISED SEPTEMBER 2011
www.ti.com
PROPAGATION DELAY TIME,
HIGH-TO-LOW-LEVEL OUTPUT
vs
SUPPLY VOLTAGE
PROPAGATION DELAY TIME,
LOW-TO-HIGH-LEVEL OUTPUT
vs
SUPPLY VOLTAGE
40
40
TA = 25°C
TA = 25°C
35
t PHL- Propagation Delay Time,
High-to-Low-Level Output - ns
t PLH - Propagation Delay Time,
Low-to-High-Level Output - ns
35
30
25
CL = 2200 pF
20
15
CL = 1000 pF
10
CL = 0
CL = 2200 pF
30
25
20
10
5
0
4
6
8
10
12
VCC - Supply Voltage - V
14
4
6
8
10
12
VCC - Supply Voltage - V
Figure 6.
Figure 7.
RISE TIME
vs
AMBIENT TEMPERATURE
FALL TIME
vs
AMBIENT TEMPERATURE
14
20
19
VCC = 10 V
Load = 1000 pF
f = 100 kHz
19
18
17
tr - Rise Time - ns
tr - Rise Time - ns
CL = 0
5
0
18
CL = 1000 pF
15
16
15
VCC = 10 V
Load = 1000 pF
f = 100 kHz
17
16
15
14
13
12
14
11
13
-50
-25
0
25
50
75
Ambient Temperature - °C
Figure 8.
Copyright © 2005–2011, Texas Instruments Incorporated
100
125
10
-50
-25
0
25
50
75
Ambient Temperature - °C
100
125
Figure 9.
Submit Documentation Feedback
Product Folder Link(s): TPS2816-Q1 TPS2817-Q1 TPS2818-Q1 TPS2819-Q1 TPS2828-Q1 TPS2829-Q1
9
TPS2816-Q1 , TPS2817-Q1, TPS2818-Q1
TPS2819-Q1, TPS2828-Q1, TPS2829-Q1
SPRS289B – AUGUST 2005 – REVISED SEPTEMBER 2011
www.ti.com
PROPAGATION DELAY TIME,
HIGH-TO-LOW-LEVEL OUTPUT
vs
AMBIENT TEMPERATURE
PROPAGATION DELAY TIME,
LOW-TO-HIGH-LEVEL OUTPUT
vs
SUPPLY VOLTAGE
20
19
VCC = 10 V
Load = 1000 pF
f = 100 kHz
17
16
15
High-to-Low-Level Output - ns
t PHL - Propagation Delay Time,
Low-to-High-Level Output - ns
t PLH - Propagation Delay Time,
18
VCC = 10 V
Load = 1000 pF
f = 100 kHz
19
18
17
16
15
14
13
12
14
11
13
-50
-25
0
25
50
75
100
TA - Ambient Temperature - °C
10
-50
125
Figure 11.
SUPPLY CURRENT
vs
SUPPLY VOLTAGE
SUPPLY CURRENT
vs
LOAD CAPACITANCE
125
4
Load = 1000 pF
Duty Cycle = 50%
14
VCC = 10 V
f = 100 kHz
Duty Cycle = 50%
3.5
f = 1 MHz
12
ICC - Supply Current - mA
ICC - Supply Current - mA
0
25
50
75
100
TA - Ambient Temperature - °C
Figure 10.
16
10
8
f = 500 kHz
6
4
f = 40 kHz
2
f = 100 kHz
3
2.5
2
1.5
1
0.5
0
0
4
6
12
8
10
VCC - Supply Voltage - V
Figure 12.
10
-25
Submit Documentation Feedback
14
0
1000
CL - Load Capacitance - pF
2000
Figure 13.
Copyright © 2005–2011, Texas Instruments Incorporated
Product Folder Link(s): TPS2816-Q1 TPS2817-Q1 TPS2818-Q1 TPS2819-Q1 TPS2828-Q1 TPS2829-Q1
TPS2816-Q1 , TPS2817-Q1, TPS2818-Q1
TPS2819-Q1, TPS2828-Q1, TPS2829-Q1
SPRS289B – AUGUST 2005 – REVISED SEPTEMBER 2011
www.ti.com
INPUT THRESHOLD VOLTAGE
vs
SUPPLY VOLTAGE
SUPPLY CURRENT
vs
AMBIENT TEMPERATURE
9
2.5
VCC = 10 V
Load = 1000 pF
f = 100 kHz
Duty Cycle = 50%
8
VIT - Input Threshold Voltage - V
ICC - Supply Current - mA
3
2
1.5
7
Positive Going
6
5
4
Negative Going
3
2
1
1
-50
-25
0
25
50
75
100
TA - Ambient Temperature - °C
0
125
4
6
Figure 14.
14
Figure 15.
REGULATOR QUIESCENT CURRENT
vs
REGULATOR SUPPLY VOLTAGE
REGULATOR OUTPUT VOLTAGE
vs
REGULATOR SUPPLY VOLTAGE
12
670
TPS2816,17 only
No Load
665
Regulator Quiescent Current - mA
11
Regulator Output Voltage - V
12
8
10
VCC - Supply Voltage - V
10
9
8
7
6
Load = 10 kΩ
5
660
655
650
645
640
635
630
625
620
4
4
8
12
16
16
20 24
32 36
VDD - Regulator Supply Voltage - V
Figure 16.
Copyright © 2005–2011, Texas Instruments Incorporated
40
4
8
12
16
16
20 24
32 36
VDD - Regulator Supply Voltage - V
40
Figure 17.
Submit Documentation Feedback
Product Folder Link(s): TPS2816-Q1 TPS2817-Q1 TPS2818-Q1 TPS2819-Q1 TPS2828-Q1 TPS2829-Q1
11
TPS2816-Q1 , TPS2817-Q1, TPS2818-Q1
TPS2819-Q1, TPS2828-Q1, TPS2829-Q1
SPRS289B – AUGUST 2005 – REVISED SEPTEMBER 2011
www.ti.com
SHOOT-THROUGH CURRENT
vs
INPUT VOLTAGE LOW-TO-HIGH
SHOOT-THROUGH CURRENT
vs
INPUT VOLTAGE HIGH-TO-LOW
7
7
VCC = 10 V
No Load
TA = 25°C
6
Shoot-Through Current - mA
Shoot-Through Current - mA
6
5
4
3
2
5
4
3
2
1
1
0
0
0
2
4
6
VI - Input Voltage - V
Figure 18.
12
VCC = 10 V
No Load
TA = 25°C
Submit Documentation Feedback
8
10
0
2
4
6
VI - Input Voltage - V
8
10
Figure 19.
Copyright © 2005–2011, Texas Instruments Incorporated
Product Folder Link(s): TPS2816-Q1 TPS2817-Q1 TPS2818-Q1 TPS2819-Q1 TPS2828-Q1 TPS2829-Q1
TPS2816-Q1 , TPS2817-Q1, TPS2818-Q1
TPS2819-Q1, TPS2828-Q1, TPS2829-Q1
SPRS289B – AUGUST 2005 – REVISED SEPTEMBER 2011
www.ti.com
APPLICATION INFORMATION
MOSFETs are voltage-driven devices that require very little steady-state drive current. However, the large input
capacitance (200 pF to 3000 pF or greater) of these devices requires large current surges to reduce the turn-on
and turn-off times. The TPS2816 series of high-speed drivers can supply up to 2 A to a MOSFET, greatly
reducing the switching times. The fast rise times and fall times and short propagation delays allow for operation
in today's high-frequency switching converters.
In addition, MOSFETs have a limited gate-bias voltage range, usually less than 20 V. The TPS2816 series of
drivers extends this operating range by incorporating an on-board series regulator with an input range up to 40 V.
This regulator can be used to power the drivers, the PWM chip, and other circuitry, providing the power
dissipation rating is not exceeded.
When using these devices, care should be exercised in the proper placement of the driver, the switching
MOSFET, and the bypass capacitor. Because of the large input capacitance of the MOSFET, the driver should
be placed close to the gate to eliminate the possibility of oscillations caused by trace inductance ringing with the
gate capacitance of the MOSFET. When the driver output path is longer than approximately 2 in, a resistor in the
range of 10 Ω should be placed in series with the gate drive as close as possible to the MOSFET. A ceramic
bypass capacitor also is recommended to provide a source for the high-speed current transients that the
MOSFET requires. This capacitor should be placed between VCC and GND of the driver (see Figure 20 and
Figure 21).
TPS2816
VCC
1
Regulator
5
Load
2
0.1 mF
3
Input
4
Figure 20. VCC < 14 V
VDD
1
TPS2816
Regulator
5
+
0.1 mF
Input
2
3
Load
4.7 mF
4
Figure 21. VCC > 14 V
Copyright © 2005–2011, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TPS2816-Q1 TPS2817-Q1 TPS2818-Q1 TPS2819-Q1 TPS2828-Q1 TPS2829-Q1
13
TPS2816-Q1 , TPS2817-Q1, TPS2818-Q1
TPS2819-Q1, TPS2828-Q1, TPS2829-Q1
SPRS289B – AUGUST 2005 – REVISED SEPTEMBER 2011
www.ti.com
The on-board series regulator supplies approximately 20 mA of current at 11.5 V, some of which can be used for
external circuitry, if the power dissipation rating for the driver is not exceeded. When using the onboard series
regulator, an electrolytic output capacitor of 4.7 µF or larger is recommended. Although not required, a 0.1-µF
ceramic capacitor on the input of the regulator can help suppress transient currents (see ). When not used, the
regulator should be connected to VCC. Grounding VDD results in destruction of the regulator.
34 VDC
0.1 mF
+
0.1 mF
VCC
4.7 mF
TPS2816
PWM
Controller
1
Regulator
5
0.1 mF
2
VO
Out
3
4
10 mF
GND
Figure 22. Boost Application
The TPS2816 and TPS2818 drivers include active pullup circuits on the inputs to eliminate the need for external
pullup resistors when using controllers with open-collector outputs (such as the TL5001). The TPS2817 and
TPS2819 drivers have standard CMOS inputs, providing a total device operating current of less than 50 µA. All
devices switch at standard CMOS logic levels of approximately two-thirds VCC with positive-going input levels,
and approximately one-third VCC with negative-going input levels. Being CMOS drivers, these devices draw
relatively large amounts of current (approximately 5 mA) when the inputs are in the range of one-half of the
supply voltage. In normal operation, the driver input is in this range for a very short time. Care should be taken to
avoid use of very low slew-rate inputs, used under normal operating conditions. Although not destructive to the
device, slew rates slower than 0.1 V/µs are not recommended.
The BiCMOS output stage provides high instantaneous drive current to rapidly toggle the power switch and very
low drop to each rail to ensure proper operation at voltage extremes.
Low-voltage circuits (less than 14 V) that require very low quiescent currents can use the TPS2828 and
TPS2829 drivers. These drivers use typically 0.2 µA of quiescent current (with inputs high or low). They do not
have the internal regulator or the active pullup circuit, but all other specifications are the same as for the rest of
the family.
2.5-V/3.3-V, 3-A APPLICATION
Figure 23 illustrates the use of the TPS2817 with a TL5001 PWM controller and a TPS1110 in a simple
step-down converter application. The converter operates at 275 kHz and delivers either 2.5 V or 3.3 V
(determined by the value of R6) at 3 A (5 A peak) from a 5-V supply. The bill of materials is provided in Table 1.
14
Submit Documentation Feedback
Copyright © 2005–2011, Texas Instruments Incorporated
Product Folder Link(s): TPS2816-Q1 TPS2817-Q1 TPS2818-Q1 TPS2819-Q1 TPS2828-Q1 TPS2829-Q1
TPS2816-Q1 , TPS2817-Q1, TPS2818-Q1
TPS2819-Q1, TPS2828-Q1, TPS2829-Q1
SPRS289B – AUGUST 2005 – REVISED SEPTEMBER 2011
www.ti.com
Q1
TPS1110D
4.5 V to 7 V
L1
VO
3 A Continuous
5 A Peak
+
C7
C8
R5
U1
TPS2817DBV
1
C5
Regulator
+
+
CR1
5
C9
C10
C12
C13
2
GND
3
4
R4
GND
U2
TL5001CD
2
+
5
SCP
VCC
R1
R6
GND
DTC
6
C9
1
OUT
COMP FB RT
4
3
C2
R7
C11
C6
8
7
R3
C3
R2
C4
NOTE: If the parasitics of the external circuit cause the voltage to violate the Absolute Maximum Rating for the output pins,
Schottky diodes should be added from ground to output and from output to VCC.
Figure 23. Step-Down Application
Table 1. Bill of Materials
REF DES
PART NO.
DESCRIPTION
MFR
U1
TPS2817DBV
IC, MOSFET driver, single noninverting
TI
U2
TL5001CD
IC, PWM controller
TI
Q1
TPS1110D
MOSFET, p-channel, 6 A, 7 V, 75 mΩ
TI
C1, C2, C3, C8
Capacitor, ceramic, 0.1 µF, 50 V, X7R, 1206
C3
Capacitor, ceramic, 0.033 µF, 50 V, X7R, 1206
C4
Capacitor, ceramic, 2200 pF, 50 V, X7R, 0805
C6
ECS-T1CY105R
Capacitor, tantalum, 1.0 µF, 16 V, A case
Panasonic
C7
10SC47M
Capacitor, OS-Con, 47 µF, 10 V
Sanyo
C9
C10, C12
Capacitor, ceramic, 1000 pF, 50 V, X7R, 0805
10SA220M
Capacitor, OS-Con, 220 µF, 10 V
Sanyo
Capacitor, ceramic, 0.022 µF, 50 V, X7R, 0805
C11
Capacitor, ceramic, 47 µF, 50 V, X7R
C13
CR1
50WQ03F
Diode, Schottky, D-pak, 5 A, 30 V
IR
L1
SML3723
Inductor, 27 µH, ±20%, 3 A
Nova Magnetics
Copyright © 2005–2011, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TPS2816-Q1 TPS2817-Q1 TPS2818-Q1 TPS2819-Q1 TPS2828-Q1 TPS2829-Q1
15
TPS2816-Q1 , TPS2817-Q1, TPS2818-Q1
TPS2819-Q1, TPS2828-Q1, TPS2829-Q1
SPRS289B – AUGUST 2005 – REVISED SEPTEMBER 2011
www.ti.com
Table 1. Bill of Materials (continued)
REF DES
PART NO.
DESCRIPTION
R1
Resistor, CF, 47 kΩ, 1/10 W, 5%, 0805
R2
Resistor, CF, 1.5 kΩ, 1/10 W, 5%, 0805
R3
Resistor, MF, 30.1 kΩ, 1/10 W, 1%, 0805
R4
Resistor, MF, 1.00 kΩ, 1/10 W, 1%, 0805
R5
Resistor, CF, 47 Ω, 1/10 W, 5%, 0805
R6(3.3-V)
Resistor, MF, 2.32 kΩ, 1/10 W, 1%, 0805
R6 (2.5-V)
Resistor, MF, 1.50 kΩ, 1/10 W, 1%, 0805
R7
Resistor, CF, 100 W, 1/10 W, 5%, 0805
MFR
As shown in Figure 24 and Figure 25, the TPS2817 turns on the TPS1110 power switch in less than 20 ns and
off in 25 ns.
Q1 Gate
Q1 Drain
2 V/div
Q1 Drain
2 V/div
Q1 Gate
2 V/div
2 V/div
12.5 ns/div
12.5 ns/div
Figure 24. Q1 Turn-On Waveform
Figure 25. Q1 Turn-Off Waveform
The efficiency for various output currents, with a 5.25-V input, is shown in Figure 26. For a 3.3-V output, the
efficiency is greater than 90% for loads up to 2 A – exceptional for a simple, inexpensive design.
95
VO = 3.3 V
Efficiency %
90
85
VI = 5.25 V
TA = 25°C
VO = 2.5 V
80
75
70
0
0.5
1
1.5
2 2.5 3 3.5
Load Current - A
4
4.5
5
Figure 26. Converter Efficiency
16
Submit Documentation Feedback
Copyright © 2005–2011, Texas Instruments Incorporated
Product Folder Link(s): TPS2816-Q1 TPS2817-Q1 TPS2818-Q1 TPS2819-Q1 TPS2828-Q1 TPS2829-Q1
TPS2816-Q1 , TPS2817-Q1, TPS2818-Q1
TPS2819-Q1, TPS2828-Q1, TPS2829-Q1
SPRS289B – AUGUST 2005 – REVISED SEPTEMBER 2011
www.ti.com
REVISION HISTORY
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision A (September 2005) to Revision B
Page
•
Changed datasheet to XML .................................................................................................................................................. 1
•
Added top-side marking for TPS2819QDBVRQ1 ................................................................................................................. 2
•
Added ESD Ratings table ..................................................................................................................................................... 3
•
Added table note for input capacitance ................................................................................................................................ 4
•
Added typical high-level output voltage of 7 V across temperature range ........................................................................... 4
•
Added maximum supply current into VCC of 60 µA across temperature range .................................................................... 4
Copyright © 2005–2011, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): TPS2816-Q1 TPS2817-Q1 TPS2818-Q1 TPS2819-Q1 TPS2828-Q1 TPS2829-Q1
17
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
(2)
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
(4/5)
(6)
TPS2819QDBVRQ1
ACTIVE
SOT-23
DBV
5
3000
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
PAYI
TPS2829QDBVRQ1
ACTIVE
SOT-23
DBV
5
3000
RoHS & Green
NIPDAU
Level-1-260C-UNLIM
-40 to 125
PAYQ
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of
工商网监
湘ICP备2023018690号
