Sample &
Buy
Product
Folder
Support &
Community
Tools &
Software
Technical
Documents
TPS62130, TPS62130A, TPS62131, TPS62132, TPS62133
SLVSAG7C – NOVEMBER 2011 – REVISED JANUARY 2015
TPS6213x 3V-17V 3A Step-Down Converter In 3x3 QFN Package
1 Features
3 Description
•
•
•
•
•
•
•
•
•
•
•
•
•
•
The TPS6213X family is an easy to use synchronous
step down DC-DC converter optimized for
applications with high power density. A high switching
frequency of typically 2.5MHz allows the use of small
inductors and provides fast transient response as well
as high output voltage accuracy by use of the DCSControl™ topology.
1
DCS-Control™ Topology
Input Voltage Range: 3 to 17V
Up to 3A Output Current
Adjustable Output Voltage from 0.9 to 6V
Pin-Selectable Output Voltage (nominal, + 5%)
Programmable Soft Start and Tracking
Seamless Power Save Mode Transition
Quiescent Current of 17µA (typ.)
Selectable Operating Frequency
Power Good Output
100% Duty Cycle Mode
Short Circuit Protection
Over Temperature Protection
Available in a 3 × 3 mm, QFN-16 Package
With their wide operating input voltage range of 3V to
17V, the devices are ideally suited for systems
powered from either a Li-Ion or other batteries as well
as from 12V intermediate power rails. It supports up
to 3A continuous output current at output voltages
between 0.9V and 6V (with 100% duty cycle mode).
The output voltage startup ramp is controlled by the
soft-start pin, which allows operation as either a
standalone power supply or in tracking configurations.
Power sequencing is also possible by configuring the
Enable and open-drain Power Good pins.
In Power Save Mode, the devices draw quiescent
current of about 17μA from VIN. Power Save Mode,
entered automatically and seamlessly if load is small,
maintains high efficiency over the entire load range.
In Shutdown Mode, the device is turned off and
shutdown current consumption is less than 2μA.
2 Applications
•
•
•
•
•
•
Standard 12V Rail Supplies
POL Supply from Single or Multiple Li-Ion Battery
Solid-State Disk Drives
Embedded Systems
LDO replacement
Mobile PCs, Tablet, Modems, Cameras
The device, available in adjustable and fixed output
voltage versions, is packaged in a 16-pin VQFN
package measuring 3 × 3 mm (RGT).
Device Information(1)
PART NUMBER
TPS6213x
PACKAGE
VQFN (16)
BODY SIZE (NOM)
3.00 mm × 3.00 mm
(1) For all available packages, see the orderable addendum at
the end of the datasheet.
4 Simplified Schematic
Efficiency vs Output Current
(3 .. 17)V
10μF
1.8V / 3A
1 / 2.2 µH
PVIN
SW
AVIN
VOS
0.1μF
PG
EN
TPS62131
SS/TR
100kΩ
22μF
FB
3.3nF
DEF
AGND
FSW
PGND
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
TPS62130, TPS62130A, TPS62131, TPS62132, TPS62133
SLVSAG7C – NOVEMBER 2011 – REVISED JANUARY 2015
www.ti.com
Table of Contents
1
2
3
4
5
6
7
8
9
Features ..................................................................
Applications ...........................................................
Description .............................................................
Simplified Schematic.............................................
Revision History.....................................................
Device Comparison Table.....................................
Pin Configuration and Functions .........................
Specifications.........................................................
1
1
1
1
2
3
3
4
8.1
8.2
8.3
8.4
8.5
8.6
4
4
4
4
5
6
Absolute Maximum Ratings ......................................
ESD Ratings ............................................................
Recommended Operating Conditions.......................
Thermal Information ..................................................
Electrical Characteristics...........................................
Typical Characteristics ..............................................
Detailed Description .............................................. 7
9.1 Overview ................................................................... 7
9.2 Functional Block Diagram ......................................... 7
9.3 Feature Description................................................... 8
9.4 Device Functional Modes........................................ 10
10 Application and Implementation........................ 12
10.1 Application Information.......................................... 12
10.2 Typical Application ............................................... 12
10.3 System Examples ................................................. 23
11 Power Supply Recommendations ..................... 26
12 Layout................................................................... 27
12.1 Layout Guidelines ................................................. 27
12.2 Layout Example .................................................... 27
12.3 Thermal Information .............................................. 28
13 Device and Documentation Support ................. 29
13.1
13.2
13.3
13.4
13.5
Device Support ....................................................
Documentation Support .......................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
29
29
29
29
30
14 Mechanical, Packaging, and Orderable
Information ........................................................... 30
5 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision B (June 2013) to Revision C
Page
•
Added Device Information and ESD Rating tables, Feature Description section, Device Functional Modes,
Programming section, Application and Implementation section, Power Supply Recommendations section, Layout
section, Device and Documentation Support section, and Mechanical, Packaging, and Orderable Information
section ................................................................................................................................................................................... 1
•
Added "(PWM mode operation)" text string to VUVLO spec Test Conditions for clarification. ................................................. 5
•
Changed second paragraph of SS/TR description for clarification. ...................................................................................... 9
Changes from Revision A (September 2012) to Revision B
Page
•
Added device TPS62130A to data sheet Header................................................................................................................... 1
•
Added device TPS62130A to Device Comparison table. ....................................................................................................... 3
•
Added text to Power Good section regarding TPS63130A. ................................................................................................... 9
•
Added pin option to Footnote statement for Pin-Selectable Output Voltage (DEF) section................................................... 9
•
Added text to Frequency Selection (FSW) section regarding pin control............................................................................... 9
•
Added text to Tracking Function section for clarification. ..................................................................................................... 16
•
Added application example regarding TPS62130A device. ................................................................................................. 23
2
Submit Documentation Feedback
Copyright © 2011–2015, Texas Instruments Incorporated
TPS62130, TPS62130A, TPS62131, TPS62132, TPS62133
www.ti.com
SLVSAG7C – NOVEMBER 2011 – REVISED JANUARY 2015
6 Device Comparison Table
PART NUMBER (1)
OUTPUT VOLTAGE
(1)
(2)
adjustable
TPS62130
adjustable
TPS62130A (2)
1.8 V
TPS62131
3.3 V
TPS62132
5.0 V
TPS62133
Contact the factory to check availability of other fixed output voltage versions.
While TPS6213X has PG=High Z, TPS62130A features PG=Low, when device is in shutdown through EN, UVLO or Thermal Shutdown.
7 Pin Configuration and Functions
SW
3
PG
4
PGND
VOS
EN
13
Exposed
Thermal Pad
5
6
7
8
DEF
2
14
FSW
SW
15
AGND
1
16
FB
SW
PGND
16-Pin VQFN With Exposed Thermal Pad
(RGT)
Top View
12
PVIN
11
PVIN
10
AVIN
9
SS/TR
space
Pin Functions
PIN
(1)
NO.
(1)
(2)
(3)
NAME
I/O
DESCRIPTION
1,2,3
SW
O
Switch node, which is connected to the internal MOSFET switches. Connect inductor between SW and
output capacitor.
4
PG
O
Output power good (High = VOUT ready, Low = VOUT below nominal regulation) ; open drain (requires
pull-up resistor)
5
FB
I
Voltage feedback of adjustable version. Connect resistive voltage divider to this pin. It is recommended to
connect FB to AGND on fixed output voltage versions for improved thermal performance.
6
AGND
7
FSW
I
Switching Frequency Select (Low ≈ 2.5MHz, High ≈ 1.25MHz (2) for typical operation) (3)
8
DEF
I
Output Voltage Scaling (Low = nominal, High = nominal + 5%) (3)
9
SS/TR
I
Soft-Start / Tracking Pin. An external capacitor connected to this pin sets the internal voltage reference rise
time. It can be used for tracking and sequencing.
10
AVIN
I
Supply voltage for control circuitry. Connect to same source as PVIN.
11,12
PVIN
I
Supply voltage for power stage. Connect to same source as AVIN.
Analog Ground. Must be connected directly to the Exposed Thermal Pad and common ground plane.
For more information about connecting pins, see Detailed Description and Application and Implementation sections.
Connect FSW to VOUT or PG in this case.
An internal pull-down resistor keeps logic level low, if pin is floating.
Copyright © 2011–2015, Texas Instruments Incorporated
Submit Documentation Feedback
3
TPS62130, TPS62130A, TPS62131, TPS62132, TPS62133
SLVSAG7C – NOVEMBER 2011 – REVISED JANUARY 2015
www.ti.com
Pin Functions (continued)
PIN
NO.
(1)
NAME
I/O
DESCRIPTION
13
EN
I
Enable input (High = enabled, Low = disabled) (3)
14
VOS
I
Output voltage sense pin and connection for the control loop circuitry.
15,16
PGND
Power Ground. Must be connected directly to the Exposed Thermal Pad and common ground plane.
Exposed
Thermal
Pad
Must be connected to AGND (pin 6), PGND (pin 15,16) and common ground plane. See the Layout
Example. Must be soldered to achieve appropriate power dissipation and mechanical reliability.
8 Specifications
8.1 Absolute Maximum Ratings (1)
over operating free-air temperature range (unless otherwise noted)
Pin voltage range (2)
MIN
MAX
AVIN, PVIN
–0.3
20
EN, SS/TR
–0.3
VIN+0.3
SW
–0.3
VIN+0.3
DEF, FSW, FB, PG, VOS
–0.3
7
V
10
mA
Power Good sink current PG
UNIT
V
V
Operating junction temperature, TJ
–40
125
°C
Storage temperature, Tstg
–65
150
°C
(1)
(2)
Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating
conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
All voltages are with respect to network ground terminal.
8.2 ESD Ratings
VALUE
V(ESD)
(1)
(2)
(3)
Electrostatic discharge (1)
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001 (2)
±2000
Charged-device model (CDM), per JEDEC specification JESD22C101 (3)
±500
UNIT
V
ESD testing is performed according to the respective JESD22 JEDEC standard.
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
8.3 Recommended Operating Conditions
Supply Voltage, VIN (at AVIN and PVIN)
MIN
MAX
UNIT
3
17
V
Operating free air temperature, TA
–40
85
°C
Operating junction temperature, TJ
–40
125
°C
8.4 Thermal Information
THERMAL METRIC (1)
TPS6213X
RGT 16 PINS
RθJA
Junction-to-ambient thermal resistance
RθJCtop
Junction-to-case(top) thermal resistance
15
RθJB
Junction-to-board thermal resistance
11
ψJT
Junction-to-top characterization parameter
0.5
ψJB
Junction-to-board characterization parameter
10
RθJCbot
Junction-to-case(bottom) thermal resistance
3.5
(1)
4
UNITS
29.1
°C/W
For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
Submit Documentation Feedback
Copyright © 2011–2015, Texas Instruments Incorporated
TPS62130, TPS62130A, TPS62131, TPS62132, TPS62133
www.ti.com
SLVSAG7C – NOVEMBER 2011 – REVISED JANUARY 2015
8.5 Electrical Characteristics
over free-air temperature range (TA=-40°C to +85°C), typical values at VIN=12V and TA=25°C (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
SUPPLY
VIN
Input voltage range (1)
17
V
IQ
Operating quiescent current
EN=High, IOUT=0mA, device not switching
17
25
µA
ISD
Shutdown current (2)
EN=Low
1.5
4
µA
2.7
2.8
VUVLO
TSD
3
Undervoltage lockout threshold
Falling Input Voltage (PWM mode operation)
2.6
Hysteresis
200
Thermal shutdown temperature
160
Thermal shutdown hysteresis
V
mV
°C
20
CONTROL (EN, DEF, FSW, SS/TR, PG)
VH
High level input threshold voltage (EN,
DEF, FSW)
VL
Low level input threshold voltage (EN,
DEF, FSW)
ILKG
Input leakage current (EN, DEF, FSW)
VTH_PG
Power good threshold voltage
VOL_PG
Power good output low
IPG=–2mA
ILKG_PG
Input leakage current (PG)
VPG=1.8V
ISS/TR
SS/TR pin source current
0.9
0.65
0.45
EN=VIN or GND; DEF, FSW=VOUT or GND
V
0.3
V
0.01
1
µA
Rising (%VOUT)
92%
95%
98%
Falling (%VOUT)
87%
90%
94%
0.07
0.3
V
1
400
nA
2.5
2.7
µA
VIN≥6V
90
170
VIN=3V
120
VIN≥6V
40
VIN=3V
50
2.3
POWER SWITCH
High-side MOSFET ON-resistance
RDS(ON)
Low-side MOSFET ON-resistance
ILIMF
High-side MOSFET forward current limit (3)
VIN =12V, TA= 25°C
3.6
4.2
70
4.9
mΩ
mΩ
A
OUTPUT
VREF
Internal reference voltage (4)
ILKG_FB
Input leakage current (FB)
TPS62130, VFB=0.8V
Output voltage range (TPS62130)
VIN ≥ VOUT
DEF (Output voltage programming)
DEF=0 (GND)
VOUT
DEF=1 (VOUT)
VOUT+5%
VOUT
(1)
(2)
(3)
(4)
(5)
(6)
Initial output voltage accuracy
0.8
(5)
1
0.9
V
100
nA
6.0
V
PWM mode operation, VIN ≥ VOUT +1V
–1.8%
1.8%
PWM mode operation, VIN ≥ VOUT +1V,
TA = –10°C to 85°C
–1.5%
1.6%
Power Save Mode operation, COUT=22µF
–2.3%
2.8%
Load regulation (6)
VIN=12V, VOUT=3.3V, PWM mode operation
0.05
%/A
Line regulation (6)
3V ≤ VIN ≤ 17V, VOUT=3.3V, IOUT= 1A, PWM
mode operation
0.02
%/V
The device is still functional down to Under Voltage Lockout (see parameter VUVLO).
Current into AVIN+PVIN pin.
This is the static current limit. It can be temporarily higher in applications due to internal propagation delay (see Current Limit And Short
Circuit Protection section).
This is the voltage regulated at the FB pin.
This is the accuracy provided by the device itself (line and load regulation effects are not included). For the fixed voltage versions the
(internal) resistive divider is included.
Line and load regulation depend on external component selection and layout (see Figure 22 and Figure 23).
Copyright © 2011–2015, Texas Instruments Incorporated
Submit Documentation Feedback
5
TPS62130, TPS62130A, TPS62131, TPS62132, TPS62133
SLVSAG7C – NOVEMBER 2011 – REVISED JANUARY 2015
www.ti.com
50.0
5.0
45.0
4.5
40.0
4.0
Input Current (µA)
Input Current (µA)
8.6 Typical Characteristics
35.0
30.0
25°C
25.0
85°C
20.0
15.0
10.0
85°C
3.0
2.5
2.0
1.5
1.0
−40°C
5.0
0.0
0.0
3.5
3.0
6.0
−40°C
25°C
0.5
9.0
12.0
Input Voltage (V)
15.0
0.0
0.0
18.0 20.0
3.0
6.0
G001
Figure 1. Quiescent Current
9.0
12.0
Input Voltage (V)
15.0
18.0 20.0
G001
Figure 2. Shutdown Current
100.0
200.0
160.0
125°C
RDSon Low−Side (mΩ)
RDSon High−Side (mΩ)
180.0
140.0
120.0
85°C
100.0
25°C
80.0
60.0
−10°C
−40°C
40.0
80.0
125°C
60.0
40.0
85°C
25°C
−10°C
20.0
−40°C
20.0
0.0
0.0
3.0
6.0
9.0
12.0
Input Voltage (V)
15.0
18.0 20.0
Figure 3. High-Side Switch Resistance
6
Submit Documentation Feedback
G001
0.0
0.0
3.0
6.0
9.0
12.0
Input Voltage (V)
15.0
18.0 20.0
G001
Figure 4. Low-Side Switch Resistance
Copyright © 2011–2015, Texas Instruments Incorporated
TPS62130, TPS62130A, TPS62131, TPS62132, TPS62133
www.ti.com
SLVSAG7C – NOVEMBER 2011 – REVISED JANUARY 2015
9 Detailed Description
9.1 Overview
The TPS6213X synchronous switched mode power converters are based on DCS-Control™ (Direct Control with
Seamless Transition into Power Save Mode), an advanced regulation topology, that combines the advantages of
hysteretic, voltage mode and current mode control including an AC loop directly associated to the output voltage.
This control loop takes information about output voltage changes and feeds it directly to a fast comparator stage.
It sets the switching frequency, which is constant for steady state operating conditions, and provides immediate
response to dynamic load changes. To get accurate DC load regulation, a voltage feedback loop is used. The
internally compensated regulation network achieves fast and stable operation with small external components
and low ESR capacitors.
The DCS-ControlTM topology supports PWM (Pulse Width Modulation) mode for medium and heavy load
conditions and a Power Save Mode at light loads. During PWM, it operates at its nominal switching frequency in
continuous conduction mode. This frequency is typically about 2.5MHz or 1.25MHz with a controlled frequency
variation depending on the input voltage. If the load current decreases, the converter enters Power Save Mode to
sustain high efficiency down to very light loads. In Power Save Mode the switching frequency decreases linearly
with the load current. Since DCS-ControlTM supports both operation modes within one single building block, the
transition from PWM to Power Save Mode is seamless without effects on the output voltage.
Fixed output voltage versions provide smallest solution size and lowest current consumption, requiring only 4
external components. An internal current limit supports nominal output currents of up to 3A.
The TPS6213X family offers both excellent DC voltage and superior load transient regulation, combined with
very low output voltage ripple, minimizing interference with RF circuits.
9.2 Functional Block Diagram
PG
Soft
start
Thermal
Shtdwn
UVLO
AVIN
PVIN PVIN
PG control
HS lim
comp
EN*
SW
SS/TR
power
control
control logic
DEF
gate
drive
SW
*
SW
FSW*
comp
LS lim
VOS
direct control
&
compensation
ramp
_
FB
comparator
+
timer tON
error
amplifier
DCS - ControlTM
*
This pin is connected to a pull down resistor internally
(see Detailed Description section).
AGND
PGND PGND
Figure 5. TPS62130 and TPS62130A (Adjustable Output Voltage)
Copyright © 2011–2015, Texas Instruments Incorporated
Submit Documentation Feedback
7
TPS62130, TPS62130A, TPS62131, TPS62132, TPS62133
SLVSAG7C – NOVEMBER 2011 – REVISED JANUARY 2015
www.ti.com
Functional Block Diagram (continued)
PG
Soft
start
Thermal
Shtdwn
UVLO
AVIN
PVIN PVIN
PG control
HS lim
comp
EN*
SW
SS/TR
power
control
control logic
gate
drive
SW
DEF*
SW
FSW*
comp
LS lim
VOS
direct control
&
compensation
ramp
_
FB*
comparator
+
timer tON
error
amplifier
DCS - ControlTM
*
This pin is connected to a pull down resistor internally
(see Detailed Description section).
AGND
PGND PGND
Figure 6. TPS62131/2/3 (Fixed Output Voltage)
9.3 Feature Description
9.3.1 Enable / Shutdown (EN)
When Enable (EN) is set High, the device starts operation. Shutdown is forced if EN is pulled Low with a
shutdown current of typically 1.5µA. During shutdown, the internal power MOSFETs as well as the entire control
circuitry are turned off. The internal resistive divider pulls down the output voltage smoothly. The EN signal must
be set externally to High or Low. An internal pull-down resistor of about 400kΩ is connected and keeps EN logic
low, if Low is set initially and then the pin gets floating. It is disconnected if the pin is set High.
Connecting the EN pin to an appropriate output signal of another power rail provides sequencing of multiple
power rails.
9.3.2 Soft Start / Tracking (SS/TR)
The internal soft start circuitry controls the output voltage slope during startup. This avoids excessive inrush
current and ensures a controlled output voltage rise time. It also prevents unwanted voltage drops from highimpedance power sources or batteries. When EN is set to start device operation, the device starts switching after
a delay of about 50µs and VOUT rises with a slope controlled by an external capacitor connected to the SS/TR
pin. See Figure 34 and Figure 35 for typical startup operation.
8
Submit Documentation Feedback
Copyright © 2011–2015, Texas Instruments Incorporated
TPS62130, TPS62130A, TPS62131, TPS62132, TPS62133
www.ti.com
SLVSAG7C – NOVEMBER 2011 – REVISED JANUARY 2015
Feature Description (continued)
Using very small capacitor (or leaving SS/TR pin un-connected) provides fastest startup behavior. The
TPS6213X can start into a pre-biased output. During monotonic pre-biased startup, both the power MOSFETs
are not allowed to turn on until the device's internal ramp sets an output voltage above the pre-bias voltage. As
long as the output is below about 0.5V a reduced current limit of typically 1.6A is set internally. If the device is set
to shutdown (EN=GND), undervoltage lockout or thermal shutdown, an internal resistor pulls the SS/TR pin down
to ensure a proper low level. Returning from those states causes a new startup sequence as set by the SS/TR
connection.
A voltage supplied to SS/TR can be used for tracking a master voltage. The output voltage will follow this voltage
in both directions up and down (see Application and Implementation).
9.3.3 Power Good (PG)
The TPS6213X has a built in power good (PG) function to indicate whether the output voltage has reached its
appropriate level or not. The PG signal can be used for startup sequencing of multiple rails. The PG pin is an
open-drain output that requires a pull-up resistor (to any voltage below 7V). It can sink 2mA of current and
maintain its specified logic low level. With TPS62130 it is high impedance when the device is turned off due to
EN, UVLO or thermal shutdown. TPS62130A features PG=Low in this case and can be used to actively
discharge Vout (see Figure 41). VIN must remain present for the PG pin to stay Low. See SLVA644 for
application details.
9.3.4 Pin-Selectable Output Voltage (DEF)
The output voltage of the TPS6213X devices can be increased by 5% above the nominal voltage by setting the
DEF pin to High (1). When DEF is Low, the device regulates to the nominal output voltage. Increasing the nominal
voltage allows adapting the power supply voltage to the variations of the application hardware. More detailed
information on voltage margining using TPS6213X can be found in SLVA489. A pull down resistor of about
400kOhm is internally connected to the pin, to ensure a proper logic level if the pin is high impedance or floating
after initially set to Low. The resistor is disconnected if the pin is set High.
9.3.5 Frequency Selection (FSW)
To get high power density with very small solution size, a high switching frequency allows the use of small
external components for the output filter. However switching losses increase with the switching frequency. If
efficiency is the key parameter, more than solution size, the switching frequency can be set to half (1.25 MHz
typ.) by pulling FSW to High. It is mandatory to start with FSW=Low to limit inrush current, which can be done by
connecting to VOUT or PG. Running with lower frequency a higher efficiency, but also a higher output voltage
ripple, is achieved. Pull FSW to Low for high frequency operation (2.5 MHz typ.). To get low ripple and full output
current at the lower switching frequency, it's recommended to use an inductor of at least 2.2uH. The switching
frequency can be changed during operation, if needed. A pull down resistor of about 400kOhm is internally
connected to the pin, acting the same way as at the DEF Pin (see above).
9.3.6 Under Voltage Lockout (UVLO)
If the input voltage drops, the under voltage lockout prevents misoperation of the device by switching off both the
power FETs. The under voltage lockout threshold is set typically to 2.7V. The device is fully operational for
voltages above the UVLO threshold and turns off if the input voltage trips the threshold. The converter starts
operation again once the input voltage exceeds the threshold by a hysteresis of typically 200mV.
9.3.7 Thermal Shutdown
The junction temperature (Tj) of the device is monitored by an internal temperature sensor. If Tj exceeds 160°C
(typ), the device goes into thermal shut down. Both the high-side and low-side power FETs are turned off and PG
goes high impedance. When Tj decreases below the hysteresis amount, the converter resumes normal
operation, beginning with Soft Start. To avoid unstable conditions, a hysteresis of typically 20°C is implemented
on the thermal shut down temperature.
(1)
Maximum allowed voltage is 7V. Therefore it's recommended to connect it to VOUT or PG, not VIN.
Copyright © 2011–2015, Texas Instruments Incorporated
Submit Documentation Feedback
9
TPS62130, TPS62130A, TPS62131, TPS62132, TPS62133
SLVSAG7C – NOVEMBER 2011 – REVISED JANUARY 2015
www.ti.com
9.4 Device Functional Modes
9.4.1 Pulse Width Modulation (PWM) Operation
The TPS6213X operates with pulse width modulation in continuous conduction mode (CCM) with a nominal
switching frequency of 2.5 MHz or 1.25MHz, selectable with the FSW pin. The frequency variation in PWM is
controlled and depends on VIN, VOUT and the inductance. The device operates in PWM mode as long the output
current is higher than half the inductor's ripple current. To maintain high efficiency at light loads, the device
enters Power Save Mode at the boundary to discontinuous conduction mode (DCM). This happens if the output
current becomes smaller than half the inductor's ripple current.
9.4.2 Power Save Mode Operation
The TPS6213X enters its built in Power Save Mode seamlessly if the load current decreases. This secures a
high efficiency in light load operation. The device remains in Power Save Mode as long as the inductor current is
discontinuous.
In Power Save Mode the switching frequency decreases linearly with the load current maintaining high efficiency.
The transition into and out of Power Save Mode happens within the entire regulation scheme and is seamless in
both directions.
TPS6213X includes a fixed on-time circuitry. An estimate for this on-time, in steady-state operation, is:
t ON =
VOUT
× 400ns
V IN
(1)
For very small output voltages, an absolute minimum on-time of about 80ns is kept to limit switching losses. The
operating frequency is thereby reduced from its nominal value, which keeps efficiency high. Using tON, the typical
peak inductor current in Power Save Mode can be approximated by:
I LPSM ( peak ) =
(V IN - VOUT )
× t ON
L
(2)
When VIN decreases to typically 15% above VOUT, the TPS6213X won't enter Power Save Mode, regardless of
the load current. The device maintains output regulation in PWM mode.
9.4.3 100% Duty-Cycle Operation
The duty cycle of the buck converter is given by D=Vout/Vin and increases as the input voltage comes close to
the output voltage. In this case, the device starts 100% duty cycle operation turning on the high-side switch
100% of the time. The high-side switch stays turned on as long as the output voltage is below the internal set
point. This allows the conversion of small input to output voltage differences, e.g. for longest operation time of
battery-powered applications. In 100% duty cycle mode, the low-side FET is switched off.
The minimum input voltage to maintain output voltage regulation, depending on the load current and the output
voltage level, can be calculated as:
spacing
VIN (min) = VOUT (min) + I OUT (RDS ( on ) + RL )
(3)
where
IOUT is the output current,
RDS(on) is the RDS(on) of the high-side FET and
RL is the DC resistance of the inductor used.
10
Submit Documentation Feedback
Copyright © 2011–2015, Texas Instruments Incorporated
TPS62130, TPS62130A, TPS62131, TPS62132, TPS62133
www.ti.com
SLVSAG7C – NOVEMBER 2011 – REVISED JANUARY 2015
Device Functional Modes (continued)
9.4.4 Current Limit And Short Circuit Protection
The TPS6213X devices have protection against heavy load and short circuit events. If a short circuit is detected
(VOUT drops below 0.5V), the current limit is reduced to 1.6A typically. If the output voltage rises above 0.5V,
the device runs in normal operation again. At heavy loads, the current limit determines the maximum output
current. If the current limit is reached, the high-side FET is turned off. Avoiding shoot through current, then the
low-side FET switches on to allow the inductor current to decrease. The low-side current limit is typically 3.5A.
The high-side FET turns on again only if the current in the low-side FET has decreased below the low side
current limit threshold.
The output current of the device is limited by the current limit (see Electrical Characteristics). Due to internal
propagation delay, the actual current can exceed the static current limit during that time. The dynamic current
limit can be calculated as follows:
spacing
I peak ( typ ) = I LIMF +
VL
× t PD
L
(4)
where
ILIMF is the static current limit, specified in the Electrical Characteristics,
L is the inductor value,
VL is the voltage across the inductor (VIN - VOUT) and
tPD is the internal propagation delay.
spacing
The current limit can exceed static values, especially if the input voltage is high and very small inductances are
used. The dynamic high side switch peak current can be calculated as follows:
spacing
I peak (typ ) = I LIMF +
(VIN - VOUT )× 30ns
L
Copyright © 2011–2015, Texas Instruments Incorporated
(5)
Submit Documentation Feedback
11
TPS62130, TPS62130A, TPS62131, TPS62132, TPS62133
SLVSAG7C – NOVEMBER 2011 – REVISED JANUARY 2015
www.ti.com
10 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
10.1 Application Information
The TPS6213X is a switched mode step-down converter, able to convert a 3V to 17V input voltage into a 0.9V to
6V output voltage, providing up to 3A. It needs a minimum amount of external components. Apart from the LC
output filter and the input capacitors, only the TPS62130 (TPS62130A) with adjustable output voltage needs an
additional resistive divider to set the output voltage level.
10.2 Typical Application
1 / 2.2 µH
(3 .. 17)V
10uF
PVIN
SW
AVIN
VOS
VOUT / 3A
100k
0.1uF
EN
PG
R1
22uF
TPS62130
SS/TR
FB
3.3nF
DEF
AGND
FSW
PGND
R2
Figure 7. 3A Step-Down Converter for Point-Of-Load Power Supply Using TPS62130
10.2.1 Design Requirements
The following design guideline provides a component selection to operate the device within the recommended
operating conditions. Using the FSW pin, the design can be optimized for highest efficiency or smallest solution
size and lowest output voltage ripple. For highest efficiency set FSW=High and the device operates at the lower
switching frequency. For smallest solution size and lowest output voltage ripple set FSW=Low and the device
operates with higher switching frequency. The typical values for all measurements are VIN=12V, VOUT=3.3V and
T=25°C, using the external components of Table 1.
The component selection used for measurements is given as follows:
Table 1. List Of Components (1)
REFERENCE
DESCRIPTION
IC
17V, 3A Step-Down Converter, QFN
L1
2.2µH, 0.165 x 0.165 in
Cin
10µF, 25V, Ceramic
Standard
Cout
22µF, 6.3V, Ceramic
Standard
Cs
3300pF, 25V, Ceramic
R1
depending on Vout
R2
depending on Vout
R3
100kΩ, Chip, 0603, 1/16W, 1%
(1)
See Third-Party Products Disclaimer.
12
Submit Documentation Feedback
MANUFACTURER
TPS62130RGT, Texas Instruments
XFL4020-222MEB, Coilcraft
Standard
Copyright © 2011–2015, Texas Instruments Incorporated
TPS62130, TPS62130A, TPS62131, TPS62132, TPS62133
www.ti.com
SLVSAG7C – NOVEMBER 2011 – REVISED JANUARY 2015
10.2.2 Detailed Design Procedure
10.2.2.1 Programming The Output Voltage
While the output voltage of the TPS62130 (TPS62130A) is adjustable, the TPS62131/2/3 are programmed to
fixed output voltages. For fixed output versions, the FB pin is pulled down internally and may be left floating. It is
recommended to connect to AGND to improve thermal resistance. The adjustable version can be programmed
for output voltages from 0.9V to 6V by using a resistive divider from VOUT to AGND. The voltage at the FB pin is
regulated to 800mV. The value of the output voltage is set by the selection of the resistive divider from
Equation 6. It is recommended to choose resistor values which allow a current of at least 2uA, meaning the value
of R2 shouldn't exceed 400kΩ. Lower resistor values are recommended for highest accuracy and most robust
design. For applications requiring lowest current consumption, the use of fixed output voltage versions is
recommended.
æV
ö
R1 = R 2 çç OUT - 1÷÷
è V REF
ø
(6)
In case the FB pin gets opened, the device clamps the output voltage at the VOS pin internally to about 7.4V.
10.2.2.2 External Component Selection
The external components have to fulfill the needs of the application, but also the stability criteria of the devices
control loop. The TPS6213X is optimized to work within a range of external components. The LC output filter's
inductance and capacitance have to be considered together, creating a double pole, responsible for the corner
frequency of the converter (see Output Filter And Loop Stability). Table 2 can be used to simplify the output filter
component selection.
Table 2. Recommended LC Output Filter Combinations (1)
4.7µF
10µF
22µF
47µF
100µF
200µF
√
√
√
√
2.2µH
√
√ (2)
√
√
√
3.3µH
√
√
√
√
400µF
0.47µH
1µH
4.7µH
(1)
(2)
The values in the table are nominal values.
This LC combination is the standard value and recommended for most applications.
spacing
The TPS6213X can be run with an inductor as low as 1µH. FSW should be set Low in this case. However, for
applications running with the low frequency setting (FSW=High) or with low input voltages, 2.2µH is
recommended. More detailed information on further LC combinations can be found in SLVA463.
10.2.2.2.1 Inductor Selection
The inductor selection is affected by several effects like inductor ripple current, output ripple voltage, PWM-toPSM transition point and efficiency. In addition, the inductor selected has to be rated for appropriate saturation
current and DC resistance (DCR). Equation 7 and Equation 8 calculate the maximum inductor current under
static load conditions.
spacing
I L(max) = I OUT (max) +
DI L(max)
2
(7)
spacing
Copyright © 2011–2015, Texas Instruments Incorporated
Submit Documentation Feedback
13
TPS62130, TPS62130A, TPS62131, TPS62132, TPS62133
SLVSAG7C – NOVEMBER 2011 – REVISED JANUARY 2015
DI L(max) = VOUT
V
æ
ç 1 - OUT
ç V IN (max)
×ç
L
×f
ç (min) SW
ç
è
www.ti.com
ö
÷
÷
÷
÷
÷
ø
(8)
where
IL(max) is the maximum inductor current,
ΔIL is the Peak to Peak Inductor Ripple Current,
L(min) is the minimum effective inductor value and
fSW is the actual PWM Switching Frequency.
spacing
Calculating the maximum inductor current using the actual operating conditions gives the minimum saturation
current of the inductor needed. A margin of about 20% is recommended to add. A larger inductor value is also
useful to get lower ripple current, but increases the transient response time and size as well. The following
inductors have been used with the TPS6213X and are recommended for use:
Table 3. List Of Inductors (1)
(1)
(2)
Type
Inductance [µH]
Current [A] (2)
Dimensions [LxBxH]
mm
MANUFACTURER
XFL4020-102ME_
1.0 µH, ±20%
4.7
4 x 4 x 2.1
Coilcraft
XFL4020-152ME_
1.5 µH, ±20%
4.2
4 x 4 x 2.1
Coilcraft
XFL4020-222ME_
2.2 µH, ±20%
3.8
4 x 4 x 2.1
Coilcraft
IHLP1212BZ-11
1.0 µH, ±20%
4.5
3 x 3.6 x 2
Vishay
IHLP1212BZ-11
2.2 µH, ±20%
3.0
3 x 3.6 x 2
Vishay
SRP4020-3R3M
3.3µH, ±20%
3.3
4.8 x 4 x 2
Bourns
VLC5045T-3R3N
3.3µH, ±30%
4.0
5 x 5 x 4.5
TDK
See Third-Party Products Disclaimer
Lower of IRMS at 40°C rise or ISAT at 30% drop.
spacing
The inductor value also determines the load current at which Power Save Mode is entered:
I load ( PSM ) =
1
DI L
2
(9)
Using Equation 8, this current level can be adjusted by changing the inductor value.
10.2.2.2.2 Capacitor Selection
10.2.2.2.2.1 Output Capacitor
The recommended value for the output capacitor is 22uF. The architecture of the TPS6213X allows the use of
tiny ceramic output capacitors with low equivalent series resistance (ESR). These capacitors provide low output
voltage ripple and are recommended. To keep its low resistance up to high frequencies and to get narrow
capacitance variation with temperature, it's recommended to use X7R or X5R dielectric. Using a higher value can
have some advantages like smaller voltage ripple and a tighter DC output accuracy in Power Save Mode (see
SLVA463).
Note: In power save mode, the output voltage ripple depends on the output capacitance, its ESR and the peak
inductor current. Using ceramic capacitors provides small ESR and low ripple.
14
Submit Documentation Feedback
Copyright © 2011–2015, Texas Instruments Incorporated
TPS62130, TPS62130A, TPS62131, TPS62132, TPS62133
www.ti.com
SLVSAG7C – NOVEMBER 2011 – REVISED JANUARY 2015
10.2.2.2.2.2 Input Capacitor
For most applications, 10µF will be sufficient and is recommended, though a larger value reduces input current
ripple further. The input capacitor buffers the input voltage for transient events and also decouples the converter
from the supply. A low ESR multilayer ceramic capacitor is recommended for best filtering and should be placed
between PVIN and PGND as close as possible to those pins. Even though AVIN and PVIN must be supplied
from the same input source, it's required to place a capacitance of 0.1uF from AVIN to AGND, to avoid potential
noise coupling. An RC, low-pass filter from PVIN to AVIN may be used but is not required.
10.2.2.2.2.3 Soft Start Capacitor
A capacitance connected between SS/TR pin and AGND allows a user programmable start-up slope of the
output voltage. A constant current source supports 2.5µA to charge the external capacitance. The capacitor
required for a given soft-start ramp time for the output voltage is given by:
spacing
C SS = t SS ×
2.5mA
1.25V
[F ]
(10)
where
CSS is the capacitance (F) required at the SS/TR pin and
tSS is the desired soft-start ramp time (s).
spacing
NOTE
DC Bias effect: High capacitance ceramic capacitors have a DC Bias effect, which will
have a strong influence on the final effective capacitance. Therefore the right capacitor
value has to be chosen carefully. Package size and voltage rating in combination with
dielectric material are responsible for differences between the rated capacitor value and
the effective capacitance.
spacing
10.2.2.3 Tracking Function
If a tracking function is desired, the SS/TR pin can be used for this purpose by connecting it to an external
tracking voltage. The output voltage tracks that voltage. If the tracking voltage is between 50mV and 1.2V, the
FB pin will track the SS/TR pin voltage as described in Equation 11 and shown in Figure 8.
spacing
VFB » 0.64 × VSS / TR
(11)
VSS/TR
[V]
1.2
0.8
0.4
0.2
0.4
0.6
0.8
VFB [V]
Figure 8. Voltage Tracking Relationship
Copyright © 2011–2015, Texas Instruments Incorporated
Submit Documentation Feedback
15
TPS62130, TPS62130A, TPS62131, TPS62132, TPS62133
SLVSAG7C – NOVEMBER 2011 – REVISED JANUARY 2015
www.ti.com
Once the SS/TR pin voltage reaches about 1.2V, the internal voltage is clamped to the internal feedback voltage
and device goes to normal regulation. This works for rising and falling tracking voltages with the same behavior,
as long as the input voltage is inside the recommended operating conditions. For decreasing SS/TR pin voltage,
the device doesn't sink current from the output. So, the resulting decrease of the output voltage may be slower
than the SS/TR pin voltage if the load is light. When driving the SS/TR pin with an external voltage, do not
exceed the voltage rating of the SS/TR pin which is VIN+0.3V.
If the input voltage drops into undervoltage lockout or even down to zero, the output voltage will go to zero,
independent of the tracking voltage. Figure 9 shows how to connect devices to get ratiometric and simultaneous
sequencing by using the tracking function.
spacing
VOUT1
PVIN
SW
AVIN
VOS
EN
PG
TPS62130
SS/TR
FB
DEF
AGND
FSW
PGND
PVIN
SW
AVIN
VOS
VOUT2
R1
EN
PG
TPS62130
SS/TR
R2
FB
DEF
AGND
FSW
PGND
Figure 9. Sequence For Ratiometric And Simultaneous Startup
spacing
The resistive divider of R1 and R2 can be used to change the ramp rate of VOUT2 faster, slower or the same as
VOUT1.
A sequential startup is achieved by connecting the PG pin of VOUT1 to the EN pin of VOUT2. Ratiometric start
up sequence happens if both supplies are sharing the same soft start capacitor. Equation 10 calculates the soft
start time, though the SS/TR current has to be doubled. Details about these and other tracking and sequencing
circuits are found in SLVA470.
Note: If the voltage at the FB pin is below its typical value of 0.8V, the output voltage accuracy may have a wider
tolerance than specified.
10.2.2.4 Output Filter And Loop Stability
The devices of the TPS6213X family are internally compensated to be stable with L-C filter combinations
corresponding to a corner frequency to be calculated with Equation 12:
f LC =
1
2p L × C
(12)
Proven nominal values for inductance and ceramic capacitance are given in Table 2 and are recommended for
use. Different values may work, but care has to be taken on the loop stability which will be affected. More
information including a detailed LC stability matrix can be found in SLVA463.
16
Submit Documentation Feedback
Copyright © 2011–2015, Texas Instruments Incorporated
TPS62130, TPS62130A, TPS62131, TPS62132, TPS62133
www.ti.com
SLVSAG7C – NOVEMBER 2011 – REVISED JANUARY 2015
The TPS6213X devices, both fixed and adjustable versions, include an internal 25pF feedforward capacitor,
connected between the VOS and FB pins. This capacitor impacts the frequency behavior and sets a pole and
zero in the control loop with the resistors of the feedback divider, per equation Equation 13 and Equation 14:
spacing
f zero =
1
2p × R1 × 25 pF
(13)
spacing
f pole =
1
2p × 25 pF
æ 1
1 ö
÷÷
× çç
+
è R1 R 2 ø
(14)
spacing
Though the TPS6213X devices are stable without the pole and zero being in a particular location, adjusting their
location to the specific needs of the application can provide better performance in Power Save mode and/or
improved transient response. An external feedforward capacitor can also be added. A more detailed discussion
on the optimization for stability vs. transient response can be found in SLVA289 and SLVA466.
Copyright © 2011–2015, Texas Instruments Incorporated
Submit Documentation Feedback
17
TPS62130, TPS62130A, TPS62131, TPS62132, TPS62133
SLVSAG7C – NOVEMBER 2011 – REVISED JANUARY 2015
www.ti.com
10.2.3 Application Curves
VIN=12V, VOUT=3.3V, TA=25°C, (unless otherwise noted)
100.0
100.0
90.0
90.0
80.0
70.0
VIN=12V
VIN=17V
Efficiency (%)
Efficiency (%)
80.0
60.0
50.0
40.0
70.0
60.0
30.0
20.0
20.0
10.0
10.0
0.001
0.01
0.1
Output Current (A)
1
0.0
10
IOUT=1mA
7
100.0
100.0
90.0
90.0
80.0
80.0
70.0
70.0
VIN=17V
50.0
VIN=12V
40.0
20.0
10.0
10.0
1
0.0
10
IOUT=1mA
7
100.0
100.0
90.0
90.0
80.0
80.0
VIN=12V
60.0
VIN=17V
VIN=5V
50.0
40.0
20.0
10.0
1
Submit Documentation Feedback
IOUT=1A
IOUT=100mA
8
9
10
11
12
13
14
Input Voltage (V)
15
16
17
10
IOUT=1A IOUT=100mA
IOUT=10mA
IOUT=1mA
40.0
10.0
0.01
0.1
Output Current (A)
17
50.0
30.0
Figure 14. Efficiency with 1.25Mhz, Vout=3.3V
18
60.0
20.0
0.001
16
70.0
30.0
0.0
0.0001
15
Figure 13. Efficiency with 2.5Mhz, Vout=5V
Efficiency (%)
Efficiency (%)
Figure 12. Efficiency with 2.5Mhz, Vout=5V
70.0
11
12
13
14
Input Voltage (V)
40.0
30.0
0.01
0.1
Output Current (A)
10
IOUT=10mA
50.0
20.0
0.001
9
60.0
30.0
0.0
0.0001
8
Figure 11. Efficiency with 1.25MHz, Vout=5V
Efficiency (%)
Efficiency (%)
Figure 10. Efficiency with 1.25MHz, Vout=5V
60.0
IOUT=1A
IOUT=100mA
40.0
30.0
0.0
0.0001
IOUT=10mA
50.0
0.0
4
5
6
7
8
9 10 11 12 13 14 15 16 17
Input Voltage (V)
Figure 15. Efficiency with 1.25Mhz, Vout=3.3V
Copyright © 2011–2015, Texas Instruments Incorporated
TPS62130, TPS62130A, TPS62131, TPS62132, TPS62133
www.ti.com
SLVSAG7C – NOVEMBER 2011 – REVISED JANUARY 2015
100.0
100.0
90.0
90.0
80.0
80.0
70.0
70.0
60.0
VIN=12V
50.0
Efficiency (%)
Efficiency (%)
VIN=12V, VOUT=3.3V, TA=25°C, (unless otherwise noted)
VIN=17V
VIN=5V
40.0
60.0
30.0
20.0
20.0
10.0
10.0
0.001
0.01
0.1
Output Current (A)
1
0.0
10
4
100.0
100.0
90.0
90.0
80.0
80.0
70.0
VIN=12V
50.0
VIN=17V
VIN=5V
40.0
20.0
10.0
0.0
10
3
100.0
100.0
90.0
90.0
80.0
80.0
70.0
VIN=12V
VIN=17V
50.0
VIN=5V
40.0
20.0
10.0
Figure 20. Efficiency with 1.25Mhz, Vout=0.9V
Copyright © 2011–2015, Texas Instruments Incorporated
6
7
IOUT=10mA
IOUT=1mA
8 9 10 11 12 13 14 15 16 17
Input Voltage (V)
10
IOUT=1A
IOUT=100mA
40.0
10.0
1
5
50.0
20.0
0.01
0.1
Output Current (A)
4
60.0
30.0
0.001
IOUT=100mA
70.0
30.0
0.0
0.0001
9 10 11 12 13 14 15 16 17
Input Voltage (V)
Figure 19. Efficiency with 1.25Mhz, Vout=1.8V
Efficiency (%)
Efficiency (%)
Figure 18. Efficiency with 1.25Mhz, Vout=1.8V
60.0
8
40.0
10.0
1
7
50.0
30.0
0.01
0.1
Output Current (A)
6
IOUT=1A
60.0
20.0
0.001
5
70.0
30.0
0.0
0.0001
IOUT=1A
Figure 17. Efficiency with 2.5Mhz, Vout=3.3V
Efficiency (%)
Efficiency (%)
Figure 16. Efficiency with 2.5Mhz, Vout=3.3V
60.0
IOUT=1mA
IOUT=10mA
40.0
30.0
0.0
0.0001
IOUT=100mA
50.0
0.0
3
4
5
6
7
IOUT=10mA
IOUT=1mA
8 9 10 11 12 13 14 15 16 17
Input Voltage (V)
Figure 21. Efficiency with 1.25Mhz, Vout=0.9V
Submit Documentation Feedback
19
TPS62130, TPS62130A, TPS62131, TPS62132, TPS62133
SLVSAG7C – NOVEMBER 2011 – REVISED JANUARY 2015
www.ti.com
VIN=12V, VOUT=3.3V, TA=25°C, (unless otherwise noted)
3.40
3.40
Output Voltage (V)
Output Voltage (V)
VIN=17V
3.35
VIN=12V
3.30
VIN=5V
3.25
3.20
0.0001
0.001
0.01
0.1
Output Current (A)
1
Figure 22. Output Voltage Accuracy (Load Regulation)
IOUT=1A
IOUT=100mA
3.25
4
7
10
13
Input Voltage (V)
16
Figure 23. Output Voltage Accuracy (Line Regulation)
4
4
IOUT=2A
3.5
IOUT=3A
Switching Frequency (MHz)
3.5
Switching Frequency (MHz)
IOUT=10mA
3.30
3.20
10
IOUT=1mA
3.35
3
2.5
2
IOUT=0.5A
IOUT=1A
1.5
1
0.5
3
2.5
2
1.5
1
0.5
0
4
6
8
10
12
Input Voltage (V)
14
16
0
18
FSW = Low
0
0.5
1
1.5
2
Output Current (A)
2.5
3
FSW = Low
Figure 24. Switching Frequency vs Input Voltage
Figure 25. Switching Frequency vs Output Current
6
0.05
0.04
Output Current (A)
Output Voltage Ripple (V)
5.5
0.03
VIN=17V
VIN=5V
0.02
4
3.5
3
2.5
25°C
85°C
2
1
VIN=12V
0
0.3
0.6
0.9
1.2 1.5 1.8 2.1
Output Current (A)
2.4
Figure 26. Output Voltage Ripple
20
−40°C
1.5
0.01
0
5
4.5
Submit Documentation Feedback
2.7
3
0.5
0
4
5
6
7
8
9 10 11 12 13 14 15 16 17
Input Voltage (V)
Figure 27. Maximum Output Current
Copyright © 2011–2015, Texas Instruments Incorporated
TPS62130, TPS62130A, TPS62131, TPS62132, TPS62133
www.ti.com
SLVSAG7C – NOVEMBER 2011 – REVISED JANUARY 2015
VIN=12V, VOUT=3.3V, TA=25°C, (unless otherwise noted)
100
100
90
70
VIN=17V
PSRR (dB)
PSRR (dB)
VIN=5V
80
VIN=12V
70
60
50
40
30
VIN=17V
60
50
40
30
20
20
VOUT=3.3V, IOUT=1A
L=2.2uH (XFL4020)
Cin=10uF, Cout=22uF
10
0
VIN=12V
90
VIN=5V
80
10
100
1k
10k
Frequency (Hz)
VOUT=3.3V, IOUT=0.1A
L=2.2uH (XFL4020)
Cin=10uF, Cout=22uF
10
100k
1M
G000
0
10
100
1k
10k
Frequency (Hz)
100k
1M
G000
Figure 28. Power Supply Rejection Ratio, FSW=2.5Mhz
Figure 29. Power Supply Rejection Ratio, FSW= 2.5MHz
Figure 30. PWM-PSM-Transition (VIN=12V, VOUT=3.3 V with
50 mV/Div)
Figure 31. Load Transient Response (IOUT= 0.5 to 3 to 0.5
A)
Figure 32. Load Transient Response of Figure 31,
Rising Edge
Figure 33. Load Transient Response of Figure 31,
Falling Edge
Copyright © 2011–2015, Texas Instruments Incorporated
Submit Documentation Feedback
21
TPS62130, TPS62130A, TPS62131, TPS62132, TPS62133
SLVSAG7C – NOVEMBER 2011 – REVISED JANUARY 2015
www.ti.com
Figure 34. Startup Into 100mA
Figure 35. Startup Into 3A
Figure 36. Typical Operation In PWM Mode (IOUT=1A)
Figure 37. Typical Operation In Power Save Mode
(IOUT=10mA)
125
125
115
115
Free−Air Temperature (°C)
Free−Air Temperature (°C)
VIN=12V, VOUT=3.3V, TA=25°C, (unless otherwise noted)
105
95
85
75
0
0.5
1
1.5
2
2.5
Output Current (A)
3
3.5
TPS62130EVM
L = 2.2 µH (XFL4020)
Figure 38. Maximum Ambient Temperature (FSW= 2.5MHz)
22
95
85
75
65
65
55
105
Submit Documentation Feedback
55
0
2
4
6
8
Output Power (W)
10
12
TPS62130EVM
L = 2.2 µH (XFL4020)
Figure 39. Maximum Ambient Temperature (FSW= 2.5MHz)
Copyright © 2011–2015, Texas Instruments Incorporated
TPS62130, TPS62130A, TPS62131, TPS62132, TPS62133
www.ti.com
SLVSAG7C – NOVEMBER 2011 – REVISED JANUARY 2015
10.3 System Examples
10.3.1 LED Power Supply
The TPS62130 can be used as a power supply for power LEDs. The FB pin can be easily set down to lower
values than nominal by using the SS/TR pin. With that, the voltage drop on the sense resistor is low to avoid
excessive power loss. Since this pin provides 2.5µA, the feedback pin voltage can be adjusted by an external
resistor per Equation 15. This drop, proportional to the LED current, is used to regulate the output voltage (anode
voltage) to a proper level to drive the LED. Both analog and PWM dimming are supported with the TPS62130.
Figure 40 shows an application circuit, tested with analog dimming:
spacing
(4 .. 17) V
2.2µH
10uF
PVIN
SW
AVIN
VOS
EN
ADIM
PG
22uF
TPS62130
SS/TR
187k
FB
DEF
AGND
FSW
PGND
0.1R
Figure 40. Single Power LED Supply
spacing
The resistor at SS/TR sets the FB voltage to a level of about 300mV and is calculated from Equation 15.
spacing
V FB = 0.64 × 2.5mA × R SS / TR
(15)
spacing
The device now supplies a constant current, set by the resistor at the FB pin, by regulating the output voltage
accordingly. The minimum input voltage has to be rated according the forward voltage needed by the LED used.
More information is available in the Application Note SLVA451.
spacing
10.3.2 Active Output Discharge
The TPS62130A pulls the PG pin Low, when the device is shut down by EN, UVLO or thermal shutdown.
Connecting PG to Vout through a resistor can be used to discharge Vout in those cases (see Figure 41). The
discharge rate can be adjusted by R3, which is also used to pull up the PG pin in normal operation. For reliability,
keep the maximum current into the PG pin less than 10mA.
spacing
(3 .. 17)V
1 / 2.2 µH
PVIN
Vout / 3A
SW
TPS62130A
AVIN
10uF
3.3nF
VOS
EN
PG
SS/TR
FB
DEF
AGND
FSW
PGND
R3
R1
22uF
R2
Figure 41. Discharge Vout Through PG Pin with TPS62130A
Copyright © 2011–2015, Texas Instruments Incorporated
Submit Documentation Feedback
23
TPS62130, TPS62130A, TPS62131, TPS62132, TPS62133
SLVSAG7C – NOVEMBER 2011 – REVISED JANUARY 2015
www.ti.com
System Examples (continued)
10.3.3 –3.3V Inverting Power Supply
The TPS62130 can be used as inverting power supply by rearranging external circuitry as shown in Figure 42.
As the former GND node now represents a voltage level below system ground, the voltage difference between
VIN and VOUT has to be limited for operation to the maximum supply voltage of 17V (see Equation 16).
spacing
V IN + VOUT £ V IN max
(16)
spacing
10uF
2.2µH
(3 .. 13.7)V
PVIN
SW
AVIN
VOS
10uF
PG
EN
1.21M
TPS62130
22uF
FB
SS/TR
3.3nF
DEF
AGND
FSW
PGND
383k
-3.3V
Figure 42. –3.3V Inverting Power Supply
spacing
The transfer function of the inverting power supply configuration differs from the buck mode transfer function,
incorporating a Right Half Plane Zero additionally. The loop stability has to be adapted and an output
capacitance of at least 22µF is recommended. A detailed design example is given in SLVA469.
spacing
10.3.4 Various Output Voltages
The following example circuits show how to use the various devices and configure the external circuitry to furnish
different output voltages at 3A.
spacing
spacing
(5 .. 17)V
10uF
5V / 3A
1 / 2.2 µH
PVIN
SW
AVIN
VOS
100k
0.1uF
PG
EN
22uF
TPS62133
SS/TR
FB
3.3nF
DEF
AGND
FSW
PGND
Figure 43. 5V/3A Power Supply
spacing
spacing
spacing
24
Submit Documentation Feedback
Copyright © 2011–2015, Texas Instruments Incorporated
TPS62130, TPS62130A, TPS62131, TPS62132, TPS62133
www.ti.com
SLVSAG7C – NOVEMBER 2011 – REVISED JANUARY 2015
System Examples (continued)
(3.3 .. 17)V
3.3V / 3A
1 / 2.2 µH
10uF
PVIN
SW
AVIN
VOS
100k
0.1uF
PG
EN
22uF
TPS62132
FB
SS/TR
3.3nF
DEF
AGND
FSW
PGND
Figure 44. 3.3V/3A Power Supply
spacing
spacing
1 / 2.2 µH
(3 .. 17)V
10uF
PVIN
SW
AVIN
VOS
2.5V / 3A
100k
0.1uF
PG
EN
390k
22uF
TPS62130
FB
SS/TR
3.3nF
DEF
AGND
FSW
PGND
180k
Figure 45. 2.5V/3A Power Supply
spacing
spacing
(3 .. 17)V
10uF
1.8V / 3A
1 / 2.2 µH
PVIN
SW
AVIN
VOS
0.1uF
PG
EN
100k
22uF
TPS62131
SS/TR
FB
3.3nF
DEF
AGND
FSW
PGND
Figure 46. 1.8V/3A Power Supply
spacing
spacing
spacing
Copyright © 2011–2015, Texas Instruments Incorporated
Submit Documentation Feedback
25
TPS62130, TPS62130A, TPS62131, TPS62132, TPS62133
SLVSAG7C – NOVEMBER 2011 – REVISED JANUARY 2015
www.ti.com
System Examples (continued)
1 / 2.2 µH
(3 .. 17)V
10uF
PVIN
SW
AVIN
VOS
1.5V / 3A
100k
0.1uF
PG
EN
130k
22uF
TPS62130
FB
SS/TR
3.3nF
DEF
AGND
FSW
PGND
150k
Figure 47. 1.5V/3A Power Supply
spacing
spacing
1 / 2.2 µH
(3 .. 17)V
10uF
PVIN
SW
AVIN
VOS
1.2V / 3A
100k
0.1uF
PG
EN
75k
22uF
TPS62130
FB
SS/TR
3.3nF
DEF
AGND
FSW
PGND
150k
Figure 48. 1.2V/3A Power Supply
spacing
spacing
1 / 2.2 µH
(3 .. 17)V
10uF
PVIN
SW
AVIN
VOS
1V / 3A
100k
0.1uF
PG
EN
51k
22uF
TPS62130
SS/TR
FB
3.3nF
DEF
AGND
FSW
PGND
200k
Figure 49. 1V/3A Power Supply
spacing
11 Power Supply Recommendations
The TPS6213X are designed to operate from a 3-V to 17-V input voltage supply. The input power supply's output
current needs to be rated according to the output voltage and the output current of the power rail application.
26
Submit Documentation Feedback
Copyright © 2011–2015, Texas Instruments Incorporated
TPS62130, TPS62130A, TPS62131, TPS62132, TPS62133
www.ti.com
SLVSAG7C – NOVEMBER 2011 – REVISED JANUARY 2015
12 Layout
12.1 Layout Guidelines
A proper layout is critical for the operation of a switched mode power supply, even more at high switching
frequencies. Therefore the PCB layout of the TPS6213X demands careful attention to ensure operation and to
get the performance specified. A poor layout can lead to issues like poor regulation (both line and load), stability
and accuracy weaknesses, increased EMI radiation and noise sensitivity.
See Figure 50 for the recommended layout of the TPS6213X, which is designed for common external ground
connections. Therefore both AGND and PGND pins are directly connected to the Exposed Thermal Pad. On the
PCB, the direct common ground connection of AGND and PGND to the Exposed Thermal Pad and the system
ground (ground plane) is mandatory. Also connect the VOS pin in the shortest way to VOUT at the output
capacitor. To avoid noise coupling into the VOS line, this connection should be separated from the VOUT power
line/plane as shown in Layout Example.
Provide low inductive and resistive paths for loops with high di/dt. Therefore paths conducting the switched load
current should be as short and wide as possible. Provide low capacitive paths (with respect to all other nodes) for
wires with high dv/dt. Therefore the input and output capacitance should be placed as close as possible to the IC
pins and parallel wiring over long distances as well as narrow traces should be avoided. Loops which conduct an
alternating current should outline an area as small as possible, as this area is proportional to the energy radiated.
Sensitive nodes like FB and VOS need to be connected with short wires and not nearby high dv/dt signals (e.g.
SW). As they carry information about the output voltage, they should be connected as close as possible to the
actual output voltage (at the output capacitor). The capacitor on the SS/TR pin and on AVIN as well as the FB
resistors, R1 and R2, should be kept close to the IC and connect directly to those pins and the system ground
plane.
The Exposed Thermal Pad must be soldered to the circuit board for mechanical reliability and to achieve
appropriate power dissipation.
The recommended layout is implemented on the EVM and shown in its Users Guide, SLVU437. Additionally, the
EVM Gerber data are available for download here, SLVC394.
12.2 Layout Example
GND
C
PVIN
AVIN
R2
8
C
7
R1
6
5
9
4
10
3
11
2
12
1
13
CIN
14
15
PG
16
EN
L1
to GND
plane
VOUT
COUT
to
AGND
GND
Figure 50. Layout Example
Copyright © 2011–2015, Texas Instruments Incorporated
Submit Documentation Feedback
27
TPS62130, TPS62130A, TPS62131, TPS62132, TPS62133
SLVSAG7C – NOVEMBER 2011 – REVISED JANUARY 2015
www.ti.com
12.3 Thermal Information
Implementation of integrated circuits in low-profile and fine-pitch surface-mount packages typically requires
special attention to power dissipation. Many system-dependent issues such as thermal coupling, airflow, added
heat sinks and convection surfaces, and the presence of other heat-generating components affect the powerdissipation limits of a given component.
Three basic approaches for enhancing thermal performance are listed below:
• Improving the power dissipation capability of the PCB design
• Improving the thermal coupling of the component to the PCB by soldering the Exposed Thermal Pad
• Introducing airflow in the system
For more details on how to use the thermal parameters, see the application notes: Thermal Characteristics
Application Note (SZZA017), and (SPRA953).
The TPS6213X is designed for a maximum operating junction temperature (Tj) of 125°C. Therefore the maximum
output power is limited by the power losses that can be dissipated over the actual thermal resistance, given by
the package and the surrounding PCB structures. Since the thermal resistance of the package is fixed,
increasing the size of the surrounding copper area and improving the thermal connection to the IC can reduce
the thermal resistance. To get an improved thermal behavior, it's recommended to use top layer metal to connect
the device with wide and thick metal lines. Internal ground layers can connect to vias directly under the IC for
improved thermal performance.
If short circuit or overload conditions are present, the device is protected by limiting internal power dissipation.
Experimental data, taken from the TPS62130 EVM, shows the maximum ambient temperature (without additional
cooling like airflow or heat sink), that can be allowed to limit the junction temperature to at most 125°C (see
Figure 38).
28
Submit Documentation Feedback
Copyright © 2011–2015, Texas Instruments Incorporated
TPS62130, TPS62130A, TPS62131, TPS62132, TPS62133
www.ti.com
SLVSAG7C – NOVEMBER 2011 – REVISED JANUARY 2015
13 Device and Documentation Support
13.1 Device Support
13.1.1 Third-Party Products Disclaimer
TI'S PUBLICATION OF INFORMATION REGARDING THIRD-PARTY PRODUCTS OR SERVICES DOES NOT
CONSTITUTE AN ENDORSEMENT REGARDING THE SUITABILITY OF SUCH PRODUCTS OR SERVICES
OR A WARRANTY, REPRESENTATION OR ENDORSEMENT OF SUCH PRODUCTS OR SERVICES, EITHER
ALONE OR IN COMBINATION WITH ANY TI PRODUCT OR SERVICE.
13.2 Documentation Support
•
•
•
•
•
•
•
•
•
•
•
Application Report, Voltage Margining Using the TPS62130 SLVA489
Application Report, Using the TPS62150 as Step-Down LED Driver With Dimming SLVA451
Application Report, Using the TPS6215x in an Inverting Buck-Boost Topology SLVA469
Application Report, Optimizing the TPS62130/40/50/60/70 Output Filter SLVA463
Application Report, TPS62130/40/50 Sequencing and Tracking SLVA470
Application Report, Optimizing Transient Response of Internally Compensated dc-dc Converters With
Feedforward Capacitor SLVA289
Application Report, Using a Feedforward Capacitor to Improve Stability and Bandwidth of
TPS62130/40/50/60/70 SLVA466
Application Report, Thermal Characteristics of Linear and Logic Packages Using JEDEC PCB Designs
SZZA017
Application Report, Semiconductor and IC Package Thermal Metrics SPRA953
User's Guide, TPS62130EVM-505, TPS62140EVM-505, and TPS62150EVM-505 Evaluation Modules
SLVU437
EVM Gerber Data, SLVC394
13.2.1 Related Documentation
13.2.2 Related Links
The table below lists quick access links. Categories include technical documents, support and community
resources, tools and software, and quick access to sample or buy.
Table 4. Related Links
PARTS
PRODUCT FOLDER
SAMPLE & BUY
TECHNICAL
DOCUMENTS
TOOLS &
SOFTWARE
SUPPORT &
COMMUNITY
TPS62130
Click here
Click here
Click here
Click here
Click here
TPS62130A
Click here
Click here
Click here
Click here
Click here
TPS62131
Click here
Click here
Click here
Click here
Click here
TPS62132
Click here
Click here
Click here
Click here
Click here
TPS62133
Click here
Click here
Click here
Click here
Click here
13.3 Trademarks
DCS-Control is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
13.4 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
Copyright © 2011–2015, Texas Instruments Incorporated
Submit Documentation Feedback
29
TPS62130, TPS62130A, TPS62131, TPS62132, TPS62133
SLVSAG7C – NOVEMBER 2011 – REVISED JANUARY 2015
www.ti.com
13.5 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
14 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
30
Submit Documentation Feedback
Copyright © 2011–2015, Texas Instruments Incorporated
PACKAGE OPTION ADDENDUM
www.ti.com
11-Sep-2013
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
Lead/Ball Finish
(2)
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
(4/5)
TPS62130ARGTR
ACTIVE
QFN
RGT
16
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
PA6I
TPS62130ARGTT
ACTIVE
QFN
RGT
16
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
PA6I
TPS62130RGTR
ACTIVE
QFN
RGT
16
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
PTSI
TPS62130RGTT
ACTIVE
QFN
RGT
16
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
PTSI
TPS62131RGTR
ACTIVE
QFN
RGT
16
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
QVX
TPS62131RGTT
ACTIVE
QFN
RGT
16
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
QVX
TPS62132RGTR
ACTIVE
QFN
RGT
16
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
QVY
TPS62132RGTT
ACTIVE
QFN
RGT
16
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
QVY
TPS62133RGTR
ACTIVE
QFN
RGT
16
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
QVZ
TPS62133RGTT
ACTIVE
QFN
RGT
16
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
QVZ
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
11-Sep-2013
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
6-Nov-2014
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
TPS62130ARGTR
QFN
RGT
16
TPS62130ARGTT
QFN
RGT
TPS62130RGTR
QFN
RGT
TPS62130RGTR
QFN
TPS62130RGTT
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
B0
(mm)
K0
(mm)
P1
(mm)
W
Pin1
(mm) Quadrant
3000
330.0
12.4
3.3
3.3
1.1
8.0
12.0
Q2
16
250
180.0
12.4
3.3
3.3
1.1
8.0
12.0
Q2
16
3000
330.0
12.4
3.3
3.3
1.1
8.0
12.0
Q2
RGT
16
3000
330.0
12.4
3.3
3.3
1.1
8.0
12.0
Q2
QFN
RGT
16
250
180.0
12.5
3.3
3.3
1.1
8.0
12.0
Q2
TPS62130RGTT
QFN
RGT
16
250
180.0
12.4
3.3
3.3
1.1
8.0
12.0
Q2
TPS62131RGTR
QFN
RGT
16
3000
330.0
12.4
3.3
3.3
1.1
8.0
12.0
Q2
TPS62131RGTT
QFN
RGT
16
250
180.0
12.4
3.3
3.3
1.1
8.0
12.0
Q2
TPS62132RGTR
QFN
RGT
16
3000
330.0
12.4
3.3
3.3
1.1
8.0
12.0
Q2
TPS62132RGTT
QFN
RGT
16
250
180.0
12.4
3.3
3.3
1.1
8.0
12.0
Q2
TPS62133RGTR
QFN
RGT
16
3000
330.0
12.4
3.3
3.3
1.1
8.0
12.0
Q2
TPS62133RGTT
QFN
RGT
16
250
180.0
12.4
3.3
3.3
1.1
8.0
12.0
Q2
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
6-Nov-2014
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
TPS62130ARGTR
QFN
RGT
16
3000
552.0
367.0
36.0
TPS62130ARGTT
QFN
RGT
16
250
552.0
185.0
36.0
TPS62130RGTR
QFN
RGT
16
3000
552.0
367.0
36.0
TPS62130RGTR
QFN
RGT
16
3000
338.0
355.0
50.0
TPS62130RGTT
QFN
RGT
16
250
338.0
355.0
50.0
TPS62130RGTT
QFN
RGT
16
250
552.0
185.0
36.0
TPS62131RGTR
QFN
RGT
16
3000
552.0
367.0
36.0
TPS62131RGTT
QFN
RGT
16
250
552.0
185.0
36.0
TPS62132RGTR
QFN
RGT
16
3000
552.0
367.0
36.0
TPS62132RGTT
QFN
RGT
16
250
552.0
185.0
36.0
TPS62133RGTR
QFN
RGT
16
3000
552.0
367.0
36.0
TPS62133RGTT
QFN
RGT
16
250
552.0
185.0
36.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated
工商网监
湘ICP备2023018690号
