Order
Now
Product
Folder
Support &
Community
Tools &
Software
Technical
Documents
Reference
Design
TPS62170, TPS62171, TPS62172, TPS62173
SLVSAT8E – NOVEMBER 2011 – REVISED MAY 2017
TPS6217x 3-V to 17-V, 0.5-A Step-Down Converters with DCS-Control™
1 Features
3 Description
•
•
•
•
•
•
•
•
•
•
•
•
The TPS6217x device family are easy to use
synchronous step-down DC-DC converters optimized
for applications with high power density. A high
switching frequency of typically 2.25 MHz allows the
use of small inductors and provides fast transient
response as well as high output voltage accuracy by
utilization of the DCS-Control™ topology.
1
•
•
DCS-Control™ Topology
Input Voltage Range from 3 V to 17 V
Up to 500-mA Output Current
Adjustable Output Voltage from 0.9 V to 6 V
Fixed Output Voltage Versions
Seamless Power Save Mode Transition
Typically 17-µA Quiescent Current
Power Good Output
100% Duty Cycle Mode
Short Circuit Protection
Over Temperature Protection
Pin to Pin Compatible with TPS62160 and
TPS62125
Available in a 2-mm × 2-mm 8-Pin WSON
Package
Create a Custom Design using the TPS62170 with
the WEBENCH® Power Designer
2 Applications
•
•
•
•
•
•
Standard 12-V Rail Supplies
POL Supply from Single or Multiple Li-Ion Battery
LDO Replacement
Embedded Systems
Digital Still Camera, Video
Mobile PCs, Tablet-PCs, Modems
With its wide operating input voltage range of 3 V to
17 V, the devices are ideally suited for systems
powered from either a Li-Ion or other battery as well
as from 12-V intermediate power rails. It supports up
to 0.5-A continuous output current at output voltages
between 0.9 V and 6 V (with 100% duty cycle mode).
Power sequencing is also possible by configuring the
enable and open-drain power good pins.
In power save mode, the devices show quiescent
current of about 17 μA from VIN. Power save mode,
entered automatically and seamlessly if the load is
small, maintains high efficiency over the entire load
range. In shutdown mode, the device is turned off
and shutdown current consumption is less than 2 μA.
The device, available in adjustable and fixed output
voltage versions, is packaged in a 2-mm × 2-mm 8pin WSON package (DSG).
Device Information(1)
PART NUMBER
TPS6217x
2.00 mm x 2.00 mm
SW
EN
10 uF
WSON (8)
Efficiency vs Output Current
1.8 V / 0.5 A
2.2 µH
VIN
BODY SIZE (NOM)
(1) For all available packages, see the orderable addendum at
the end of the datasheet.
Typical Application Schematic
(3 .. 17) V
PACKAGE
VOS
TPS62171
PG
PGND
FB
100k
22 uF
Efficiency (%)
AGND
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
TPS62170, TPS62171, TPS62172, TPS62173
SLVSAT8E – NOVEMBER 2011 – REVISED MAY 2017
www.ti.com
Table of Contents
1
2
3
4
5
6
7
8
Features ..................................................................
Applications ...........................................................
Description .............................................................
Revision History.....................................................
Device Voltage Options.........................................
Pin Configuration and Functions .........................
Specifications.........................................................
1
1
1
2
3
3
4
7.1
7.2
7.3
7.4
7.5
7.6
4
4
4
4
5
6
Absolute Maximum Ratings ......................................
ESD Ratings..............................................................
Recommended Operating Conditions.......................
Thermal Information ..................................................
Electrical Characteristics...........................................
Typical Characteristics ..............................................
Detailed Description .............................................. 7
8.1
8.2
8.3
8.4
Overview ................................................................... 7
Functional Block Diagram ......................................... 7
Feature Description................................................... 8
Device Functional Modes........................................ 10
9
Application and Implementation ........................ 12
9.1 Application Information............................................ 12
9.2 Typical Application .................................................. 12
9.3 System Examples ................................................... 21
10 Power Supply Recommendations ..................... 24
11 Layout................................................................... 25
11.1 Layout Guidelines ................................................. 25
11.2 Layout Example .................................................... 25
11.3 Thermal Considerations ........................................ 26
12 Device and Documentation Support ................. 27
12.1
12.2
12.3
12.4
12.5
12.6
12.7
Device Support......................................................
Documentation Support ........................................
Related Links ........................................................
Community Resources..........................................
Trademarks ...........................................................
Electrostatic Discharge Caution ............................
Glossary ................................................................
27
27
27
28
28
28
28
13 Mechanical, Packaging, and Orderable
Information ........................................................... 28
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision D (October 2014) to Revision E
Page
•
Added link to WEBENCH® Designer .................................................................................................................................... 1
•
Added "SW (AC), less than 10ns" specification to Absolute Maximum Ratings table .......................................................... 4
•
Changed TJ MAX spec from "125" to "150" ........................................................................................................................... 4
•
Changed Electrical Characteristics Conditions from "free-air temperature range" to "junction temperature range" ............. 5
•
Added IQ and ISD specifications ............................................................................................................................................. 5
•
Added 125°C plot line in Figure 1 and Figure 4 Typical Characteristics graphic entities. .................................................... 6
•
Added Power Good Pin Logic Table ..................................................................................................................................... 9
Changes from Revision C (August 2013) to Revision D
•
Page
Added Pin Configuration and Functions section, ESD Ratings table, Feature Description section, Device Functional
Modes, Application and Implementation section, Power Supply Recommendations section, Layout section, Device
and Documentation Support section, and Mechanical, Packaging, and Orderable Information section .............................. 1
Changes from Revision B (August 2013) to Revision C
•
Page
Changed 50mV/μs to 50mV/s in Enable and Shutdown (EN) section .................................................................................. 8
Changes from Revision A (April 2012) to Revision B
•
Page
Added diode to Figure 41 ..................................................................................................................................................... 24
Changes from Original (November 2011) to Revision A
•
2
Page
Changed Table 2 .................................................................................................................................................................. 13
Submit Documentation Feedback
Copyright © 2011–2017, Texas Instruments Incorporated
Product Folder Links: TPS62170 TPS62171 TPS62172 TPS62173
TPS62170, TPS62171, TPS62172, TPS62173
www.ti.com
SLVSAT8E – NOVEMBER 2011 – REVISED MAY 2017
5 Device Voltage Options
(1)
OUTPUT VOLTAGE (1)
PART NUMBER
adjustable
TPS62170
1.8 V
TPS62171
3.3 V
TPS62172
5.0 V
TPS62173
PACKAGE
WSON (8)
Contact the factory to check availability of other fixed output voltage versions.
6 Pin Configuration and Functions
DSG Package
8-Pin WSON With Exposed Thermal Pad
Top View
PGND
1
VIN
2
EN
3
AGND
4
Exposed
Thermal
Pad
8
PG
7
SW
6
VOS
5
FB
Pin Functions
PIN (1)
I/O
DESCRIPTION
NAME
NO.
PGND
1
—
Power ground
VIN
2
IN
Supply voltage
EN
3
IN
Enable input (High = enabled, Low = disabled)
AGND
4
—
Analog ground
FB
5
IN
Voltage feedback of adjustable version. Connect resistive voltage divider to this pin. It is recommended to
connect FB to AGND on fixed output voltage versions for improved thermal performance.
VOS
6
IN
Output voltage sense pin and connection for the control loop circuitry.
SW
7
OUT
Switch node, which is connected to the internal MOSFET switches. Connect inductor between SW and output
capacitor.
PG
8
OUT
Output power good (High = VOUT ready, Low = VOUT below nominal regulation); open drain (requires pullup resistor; goes high impedance, when device is switched off)
Exposed
Thermal Pad
(1)
—
Must be connected to AGND. Must be soldered to achieve appropriate power dissipation and mechanical
reliability.
For more information about connecting pins, see Detailed Description and Application Information sections.
Copyright © 2011–2017, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS62170 TPS62171 TPS62172 TPS62173
3
TPS62170, TPS62171, TPS62172, TPS62173
SLVSAT8E – NOVEMBER 2011 – REVISED MAY 2017
www.ti.com
7 Specifications
7.1 Absolute Maximum Ratings (1)
Pin voltage range (2)
MIN
MAX
UNIT
VIN
–0.3
20
V
EN, SW (DC)
–0.3
VIN+ 0.3
–2
24.5
SW (AC), less than 10ns (3)
FB, PG, VOS
Power good sink current
–0.3
PG
V
7
V
10
mA
Operating junction temperature, TJ
–40
150
°C
Storage temperature, Tstg
–65
150
°C
(1)
(2)
(3)
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
All voltages are with respect to network ground terminal.
While switching.
7.2 ESD Ratings
VALUE
V(ESD)
(1)
(2)
Electrostatic discharge
Human body model (HBM), per ANSI/ESDA/JEDEC JS-001 (1)
±2000
Charged device model (CDM), per JEDEC specification JESD22-C101 (2)
±500
UNIT
V
JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
7.3 Recommended Operating Conditions
MIN
Supply Voltage, VIN
NOM
MAX
UNIT
3
17
V
Output Voltage, VOUT
0.9
6
V
Operating junction temperature, TJ
–40
125
°C
7.4 Thermal Information
TPS6217x
THERMAL METRIC (1)
DSG (WSON)
UNIT
8 PINS
RθJA
Junction-to-ambient thermal resistance
61.8
°C/W
RθJC(top)
Junction-to-case (top) thermal resistance
61.3
°C/W
RθJB
Junction-to-board thermal resistance
15.5
°C/W
ψJT
Junction-to-top characterization parameter
0.4
°C/W
ψJB
Junction-to-board characterization parameter
15.4
°C/W
RθJC(bot)
Junction-to-case (bottom) thermal resistance
8.6
°C/W
(1)
4
For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report, SPRA953.
Submit Documentation Feedback
Copyright © 2011–2017, Texas Instruments Incorporated
Product Folder Links: TPS62170 TPS62171 TPS62172 TPS62173
TPS62170, TPS62171, TPS62172, TPS62173
www.ti.com
SLVSAT8E – NOVEMBER 2011 – REVISED MAY 2017
7.5 Electrical Characteristics
Over junction temperature range (TJ = –40°C to +125°C), typical values at VIN = 12 V and TJ = 25°C (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX UNIT
SUPPLY
Input voltage range (1)
VIN
3
IQ
Operating quiescent current
EN = High, IOUT = 0 mA,
device not switching
ISD
Shutdown current (2)
EN = Low
VUVLO
Undervoltage lockout threshold
TSD
TJ = -40°C to +85°C
TJ = -40°C to +85°C
Falling input voltage
2.6
17
17
30
17
25
1.5
25
1.5
4
2.7
2.82
Hysteresis
180
Thermal shutdown temperature
rising temperature
160
Thermal shutdown hysteresis
falling temperature
20
V
µA
µA
V
mV
°C
CONTROL (EN, PG)
VEN_H
High level input threshold voltage
(EN)
VEN_L
Low level input threshold voltage
(EN)
ILKG_E
Input leakage current (EN)
EN = VIN or GND
N
VTH_P
Power good threshold voltage
G
VOL_P
0.6
V
0.56
0.3
V
0.01
1
µA
Rising (%VOUT)
92%
95%
98%
Falling (%VOUT)
87%
90%
93%
Power good output low voltage
IPG = –2 mA
0.07
0.3
V
Input leakage current (PG)
VPG = 1.8 V
1
400
nA
VIN ≥ 6 V
300
600
VIN= 3 V
430
VIN≥ 6 V
120
VIN = 3 V
165
G
ILKG_P
0.9
G
POWER SWITCH
High-side MOSFET ON-resistance
RDS(O
N)
Low-side MOSFET ON-resistance
ILIMF
High-side MOSFET forward
current limit (3)
VIN = 12 V, TJ= 25°C
0.85
1.05
200
1.35
mΩ
mΩ
A
OUTPUT
VREF
Internal reference voltage (4)
ILKG_F
Pin leakage current (FB)
TPS62170, VFB= 1.2 V
Output voltage range (TPS62170)
VIN ≥ VOUT
B
Initial output voltage accuracy (5)
VOUT
(1)
(2)
(3)
(4)
(5)
0.8
5
V
400
nA
0.9
6.0
V
PWM mode operation, VIN ≥ VOUT + 1 V
–3%
3%
Power save mode operation, COUT= 22 µF
-3.5
%
4%
DC output voltage load regulation
VIN = 12 V, VOUT = 3.3 V, PWM mode operation
0.05
%/A
DC output voltage line regulation
3 V ≤ VIN ≤ 17 V, VOUT = 3.3 V, IOUT = 0.5 A, PWM mode
operation
0.02
%/V
The device is still functional down to under voltage lockout (see parameter VUVLO).
Current into VIN pin.
This is the static current limit. It can be temporarily higher in applications due to internal propagation delay (see Current Limit and Short
Circuit Protection).
This is the voltage regulated at the FB pin.
This is the accuracy provided by the device itself (line and load regulation effects are not included). For fixed voltage versions, the
(internal) resistive feedback divider is included.
Copyright © 2011–2017, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS62170 TPS62171 TPS62172 TPS62173
5
TPS62170, TPS62171, TPS62172, TPS62173
SLVSAT8E – NOVEMBER 2011 – REVISED MAY 2017
www.ti.com
7.6 Typical Characteristics
225.0
125°C
−40°C
125°C
200.0
175.0
85°C
150.0
25°C
125.0
−20°C
100.0
75.0
−40°C
50.0
25.0
9.0
12.0
Input Voltage (V)
Figure 3. High-Side Switch
6
Figure 2. Shutdown Current
250.0
RDSon Low−Side (mΩ)
RDSon High−Side (mΩ)
Figure 1. Quiescent Current
600.0
550.0
500.0
85°C
450.0
400.0
25°C
350.0
300.0
−20°C
250.0
200.0
150.0
100.0
50.0
0.0
3.0
6.0
Submit Documentation Feedback
15.0
18.0
G001
0.0
3.0
6.0
9.0
12.0
15.0
Input Voltage (V)
18.0
20.0
G001
Figure 4. Low-Side Switch
Copyright © 2011–2017, Texas Instruments Incorporated
Product Folder Links: TPS62170 TPS62171 TPS62172 TPS62173
TPS62170, TPS62171, TPS62172, TPS62173
www.ti.com
SLVSAT8E – NOVEMBER 2011 – REVISED MAY 2017
8 Detailed Description
8.1 Overview
The TPS6217x synchronous step-down DC-DC converters are based on DCS-Control™ (Direct Control with
Seamless transition into power save mode), an advanced regulation topology, that combines the advantages of
hysteretic, voltage mode and current mode control including an AC loop directly associated to the output voltage.
This control loop takes information about output voltage changes and feeds it directly to a fast comparator stage.
It sets the switching frequency, which is constant for steady state operating conditions, and provides immediate
response to dynamic load changes. To get accurate DC load regulation, a voltage feedback loop is used. The
internally compensated regulation network achieves fast and stable operation with small external components
and low ESR capacitors.
The DCS-Control™ topology supports pulse width modulation (PWM) mode for medium and heavy load
conditions and a power save mode at light loads. During PWM mode, it operates at its nominal switching
frequency in continuous conduction mode. This frequency is typically about 2.25 MHz with a controlled frequency
variation depending on the input voltage. If the load current decreases, the converter enters power save mode to
sustain high efficiency down to very light loads. In power save mode, the switching frequency decreases linearly
with the load current. Since DCS-Control™ supports both operation modes within one single building block, the
transition from PWM to power save mode is seamless without effects on the output voltage.
Fixed output voltage versions provide smallest solution size and lowest current consumption, requiring only 3
external components. An internal current limit supports nominal output currents of up to 500 mA.
The TPS6217x family offers both excellent DC voltage and superior load transient regulation, combined with very
low output voltage ripple, minimizing interference with RF circuits.
8.2 Functional Block Diagram
PG
Soft
start
Thermal
Shtdwn
UVLO
VIN
PG control
HS lim
comp
power
control
control logic
EN*
gate
drive
SW
comp
LS lim
VOS
direct control
&
compensation
ramp
_
FB
comparator
+
timer tON
error
amplifier
DCS - ControlTM
*
This pin is connected to a pull down resistor internally
(see Detailed Description section).
AGND
PGND
Figure 5. TPS62170 (Adjustable Output Voltage)
Copyright © 2011–2017, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS62170 TPS62171 TPS62172 TPS62173
7
TPS62170, TPS62171, TPS62172, TPS62173
SLVSAT8E – NOVEMBER 2011 – REVISED MAY 2017
www.ti.com
Functional Block Diagram (continued)
PG
Soft
start
Thermal
Shtdwn
UVLO
VIN
PG control
HS lim
comp
power
control
control logic
EN*
gate
drive
SW
comp
LS lim
VOS
direct control
&
compensation
ramp
_
FB*
comparator
+
timer tON
error
amplifier
DCS - ControlTM
*
This pin is connected to a pull down resistor internally
(see Detailed Description section).
AGND
PGND
Figure 6. TPS62171/TPS62172/TPS62173 (Fixed Output Voltage)
8.3 Feature Description
8.3.1 Enable and Shutdown (EN)
When enable (EN) is set high, the device starts operation.
Shutdown is forced if EN is pulled low with a shutdown current of typically 1.5 µA. During shutdown, the internal
power MOSFETs as well as the entire control circuitry are turned off. The internal resistive divider pulls down the
output voltage smoothly. If the EN pin is low, an internal pull-down resistor of about 400 kΩ is connected and
keeps it low, to avoid bouncing.
Connecting the EN pin to an appropriate output signal of another power rail provides sequencing of multiple
power rails.
8.3.2 Current Limit and Short Circuit Protection
The TPS6217x devices are protected against heavy load and short circuit events. At heavy loads, the current
limit determines the maximum output current. If the current limit is reached, the high-side FET is turned off.
Avoiding shoot-through current, the low-side FET is switched on to allow the inductor current to decrease. The
high-side FET turns on again, only if the current in the low-side FET decreases below the low-side current limit
threshold of typically 0.7A.
The output current of the device is limited by the current limit (see Electrical Characteristics). Due to internal
propagation delay, the actual current can exceed the static current limit during that time. The dynamic current
limit is calculated as follows:
space
8
Submit Documentation Feedback
Copyright © 2011–2017, Texas Instruments Incorporated
Product Folder Links: TPS62170 TPS62171 TPS62172 TPS62173
TPS62170, TPS62171, TPS62172, TPS62173
www.ti.com
SLVSAT8E – NOVEMBER 2011 – REVISED MAY 2017
Feature Description (continued)
I peak ( typ ) = I LIMF +
VL
× t PD
L
where
•
•
•
•
ILIMF is the static current limit, specified in Electrical Characteristics
L is the inductor value
VL is the voltage across the inductor
tPD is the internal propagation delay
(1)
space
The dynamic high-side switch peak current is calculated as follows:
space
I peak (typ ) = I LIMF +
(VIN - VOUT )× 30ns
L
(2)
space
Take care with the current limit, if the input voltage is high and very small inductances are used.
8.3.3 Power Good (PG)
The TPS6217x has a built in power good (PG) function to indicate whether the output voltage has reached its
appropriate level or not. The PG signal can be used for startup sequencing of multiple rails. The PG pin is an
open-drain output that requires a pull-up resistor (to any voltage below 7 V). It can sink 2 mA of current and
maintain its specified logic low level. It is high impedance when the device is turned off due to EN, UVLO or
thermal shutdown. If not used, the PG pin should be connected to GND but may be left floating.
space
Table 1. Power Good Pin Logic Table
PG Logic Status
Device State
Enable (EN=High)
High Impedance
VFB ≥ VTH_PG
VFB ≤ VTH_PG
Thermal Shutdown
Power Supply Removal
√
√
Shutdown (EN=Low)
UVLO
Low
√
0.7 V < VIN < VUVLO
√
TJ > TSD
√
VIN < 0.7 V
√
space
8.3.4 Undervoltage Lockout (UVLO)
If the input voltage drops, the under voltage lockout prevents misoperation of the device by switching off both the
power FETs. The under voltage lockout threshold is set typically to 2.7 V. The device is fully operational for
voltages above the UVLO threshold and turns off if the input voltage trips the threshold. The converter starts
operation again once the input voltage exceeds the threshold by a hysteresis of typically 180 mV.
8.3.5 Thermal Shutdown
The junction temperature (Tj) of the device is monitored by an internal temperature sensor. If Tj exceeds 160°C
(typical), the device goes into thermal shut down. Both the high-side and low-side power FETs are turned off and
PG goes high impedance. When Tj decreases below the hysteresis amount, the converter resumes normal
operation, beginning with soft start. To avoid unstable conditions, a hysteresis of typically 20°C is implemented
on the thermal shut down temperature.
Copyright © 2011–2017, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS62170 TPS62171 TPS62172 TPS62173
9
TPS62170, TPS62171, TPS62172, TPS62173
SLVSAT8E – NOVEMBER 2011 – REVISED MAY 2017
www.ti.com
8.4 Device Functional Modes
8.4.1 Soft Start
The internal soft start circuitry controls the output voltage slope during startup. This avoids excessive inrush
current and ensures a controlled output voltage rise time. It also prevents unwanted voltage drops from highimpedance power sources or batteries. When EN is set to start device operation, the device starts switching after
a delay of about 50 µs and VOUT rises with a slope of about 25 mV/µs. See Figure 30 and Figure 31 for typical
startup operation.
The TPS6217x can start into a pre-biased output. During monotonic pre-biased startup, the low-side MOSFET is
not allowed to turn on until the device's internal ramp sets an output voltage above the pre-bias voltage.
8.4.2 Pulse Width Modulation (PWM) Operation
The TPS6217x operates with pulse width modulation in continuous conduction mode (CCM) with a nominal
switching frequency of about 2.25 MHz. The frequency variation in PWM is controlled and depends on VIN, VOUT
and the inductance. The device operates in PWM mode as long the output current is higher than half the
inductor's ripple current. To maintain high efficiency at light loads, the device enters power save mode at the
boundary to discontinuous conduction mode (DCM). This happens if the output current becomes smaller than
half the inductor's ripple current.
8.4.3 Power Save Mode Operation
The TPS6217x's built in power save mode is entered seamlessly, if the load current decreases. This secures a
high efficiency in light load operation. The device remains in power save mode as long as the inductor current is
discontinuous.
In power save mode the switching frequency decreases linearly with the load current maintaining high efficiency.
The transition into and out of power save mode happens within the entire regulation scheme and is seamless in
both directions.
TPS6217x includes a fixed on-time circuitry. This on-time, in steady-state operation, is estimated as:
space
t ON =
VOUT
× 420ns
VIN
(3)
space
For very small output voltages, the on-time increases beyond the result of Equation 3, to stay above an absolute
minimum on-time, tON(min), which is around 80 ns, to limit switching losses. The peak inductor current in PSM is
approximated by:
space
I LPSM ( peak ) =
(V IN - VOUT )
× t ON
L
(4)
space
When VIN decreases to typically 15% above VOUT, the TPS6217x does not enter power save mode, regardless of
the load current. The device maintains output regulation in PWM mode.
8.4.4 100% Duty-Cycle Operation
The duty cycle of the buck converter is given by D = VOUT/VIN and increases as the input voltage comes close to
the output voltage. In this case, the device starts 100% duty cycle operation turning on the high-side switch
100% of the time. The high-side switch stays turned on as long as the output voltage is below the internal
setpoint. This allows the conversion of small input to output voltage differences, such as for the longest operation
time of battery-powered applications. In 100% duty cycle mode, the low-side FET is switched off.
The minimum input voltage to maintain output voltage regulation, depending on the load current and the output
voltage level, is calculated as:
10
Submit Documentation Feedback
Copyright © 2011–2017, Texas Instruments Incorporated
Product Folder Links: TPS62170 TPS62171 TPS62172 TPS62173
TPS62170, TPS62171, TPS62172, TPS62173
www.ti.com
SLVSAT8E – NOVEMBER 2011 – REVISED MAY 2017
Device Functional Modes (continued)
space
VIN (min) = VOUT (min) + I OUT (RDS ( on ) + RL )
where
•
•
•
IOUT is the output current
RDS(on) is the RDS(on) of the high-side FET
RL is the DC resistance of the inductor used
Copyright © 2011–2017, Texas Instruments Incorporated
(5)
Submit Documentation Feedback
Product Folder Links: TPS62170 TPS62171 TPS62172 TPS62173
11
TPS62170, TPS62171, TPS62172, TPS62173
SLVSAT8E – NOVEMBER 2011 – REVISED MAY 2017
www.ti.com
9 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
9.1 Application Information
The TPS6217x device family are easy to use synchronous step-down DC-DC converters optimized for
applications with high power density. A high switching frequency of typically 2.25 MHz allows the use of small
inductors and provides fast transient response as well as high output voltage accuracy by utilization of the DCSControl™ topology. With its wide operating input voltage range of 3 V to 17 V, the devices are ideally suited for
systems powered from either a Li-Ion or other battery as well as from 12-V intermediate power rails. It supports
up to 0.5-A continuous output current at output voltages between 0.9 V and 6 V (with 100% duty cycle mode).
9.2 Typical Application
space
2.2µH
VIN
VIN
VOUT
SW
EN
VOS
R3
R1
TPS62170
C1
C2
AGND
PG
PGND
FB
R2
Figure 7. TPS62170 Adjustable Power Supply
space
9.2.1 Design Requirements
The design guideline provides a component selection to operate the device within the Recommended Operating
Conditions.
9.2.2 Detailed Design Procedure
9.2.2.1 Custom Design with WEBENCH® Tools
Click here to create a custom design using the TPS62170 device with the WEBENCH® Power Designer.
1. Start by entering your VIN, VOUT, and IOUT requirements.
2. Optimize your design for key parameters like efficiency, footprint and cost using the optimizer dial and
compare this design with other possible solutions from Texas Instruments.
3. The WEBENCH Power Designer provides you with a customized schematic along with a list of materials with
real time pricing and component availability.
4. In most cases, you will also be able to:
– Run electrical simulations to see important waveforms and circuit performance
– Run thermal simulations to understand the thermal performance of your board
– Export your customized schematic and layout into popular CAD formats
– Print PDF reports for the design, and share your design with colleagues
5. Get more information about WEBENCH tools at www.ti.com/WEBENCH.
12
Submit Documentation Feedback
Copyright © 2011–2017, Texas Instruments Incorporated
Product Folder Links: TPS62170 TPS62171 TPS62172 TPS62173
TPS62170, TPS62171, TPS62172, TPS62173
www.ti.com
SLVSAT8E – NOVEMBER 2011 – REVISED MAY 2017
Typical Application (continued)
9.2.2.2 Programming the Output Voltage
While the output voltage of the TPS62170 is adjustable, the TPS62171/TPS62172/TPS62173 are programmed to
fixed output voltages. For fixed output versions, the FB pin is pulled down internally and may be left floating. it is
recommended to connect it to AGND to improve thermal resistance. The adjustable version can be programmed
for output voltages from 0.9 V to 6 V by using a resistive divider from VOUT to AGND. The voltage at the FB pin
is regulated to 800 mV. The value of the output voltage is set by the selection of the resistive divider from
Equation 6. It is recommended to choose resistor values which allow a current of at least 2 uA, meaning the
value of R2 should not exceed 400 kΩ. Lower resistor values are recommended for highest accuracy and most
robust design. For applications requiring lowest current consumption, the use of fixed output voltage versions is
recommended.
spacing
ö
æV
R1 = R 2 ç OUT - 1÷
0.8V
ø
è
(6)
spacing
In case the FB pin gets opened, the device clamps the output voltage at the VOS pin to about 7.4 V.
9.2.2.3 External Component Selection
The external components have to fulfill the needs of the application, but also the stability criteria of the devices
control loop. The TPS6217x is optimized to work within a range of external components. The LC output filter's
inductance and capacitance have to be considered together, creating a double pole, responsible for the corner
frequency of the converter (see Output Filter and Loop Stability). Table 2 can be used to simplify the output filter
component selection. Checked cells represent combinations that are proven for stability by simulation and lab
test. Further combinations should be checked for each individual application.
space
Table 2. Recommended LC Output Filter Combinations (1)
4.7µF
10µF
22µF
47µF
100µF
200µF
2.2µH
√
√ (2)
√
√
√
3.3µH
√
√
√
√
400µF
1µH
4.7µH
(1)
(2)
The values in the table are nominal values. Variations of typically ±20% due to tolerance, saturation and DC bias are assumed.
This LC combination is the standard value and recommended for most applications.
space
More detailed information on further LC combinations can be found in SLVA463.
9.2.2.3.1 Inductor Selection
The inductor selection is affected by several effects like inductor ripple current, output ripple voltage, PWM-toPSM transition point and efficiency. In addition, the inductor selected has to be rated for appropriate saturation
current and DC resistance (DCR). Equation 7 and Equation 8 calculate the maximum inductor current under
static load conditions.
spacing
IL (m ax) = IO U T (m ax) +
D IL (m ax)
2
(7)
spacing
spacing
Copyright © 2011–2017, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS62170 TPS62171 TPS62172 TPS62173
13
TPS62170, TPS62171, TPS62172, TPS62173
SLVSAT8E – NOVEMBER 2011 – REVISED MAY 2017
DI L(max) = VOUT
V
æ
ç 1 - OUT
ç V IN (max)
×ç
L
×f
ç (min) SW
ç
è
www.ti.com
ö
÷
÷
÷
÷
÷
ø
where
•
•
•
•
IL(max) is the maximum inductor current
ΔIL is the peak-to-peak inductor ripple current
L(min) is the minimum effective inductor value
fSW is the actual PWM switching frequency
(8)
spacing
Calculating the maximum inductor current using the actual operating conditions gives the minimum saturation
current of the inductor needed. A margin of about 20% is recommended to add. A larger inductor value is also
useful to get lower ripple current, but increases the transient response time and size as well. Table 3 lists
inductors that are recommended for use with the TPS6217x.
Table 3. List of Inductors
(1)
Type
Inductance [µH]
Current [A] (1)
Dimensions [L x B x H] mm
MANUFACTURER
VLF3012ST-2R2M1R4
2.2 µH, ±20%
1.9 A
3.0 x 2.8 x 1.2
TDK
VLF302512MT-2R2M
2.2 µH, ±20%
1.9 A
3.0 x 2.5 x 1.2
TDK
VLS252012-2R2
2.2 µH, ±20%
1.3 A
2.5 x 2.0 x 1.2
TDK
XFL3012-222MEC
2.2 µH, ±20%
1.9 A
3.0 x 3.0 x 1.2
Coilcraft
XFL3012-332MEC
3.3 µH, ±20%
1.6 A
3.0 x 3.0 x 1.2
Coilcraft
XPL2010-222MLC
2.2 µH, ±20%
1.3 A
1.9 x 2.0 x 1.0
Coilcraft
XPL2010-332MLC
3.3 µH, ±20%
1.1 A
1.9 x 2.0 x 1.0
Coilcraft
LPS3015-332ML
3.3 µH, ±20%
1.4 A
3.0 x 3.0 x 1.4
Coilcraft
PFL2512-222ME
2.2 µH, ±20%
1.0 A
2.8 x 2.3 x 1.2
Coilcraft
PFL2512-333ME
3.3 µH, ±20%
0.78 A
2.8 x 2.3 x 1.2
Coilcraft
744028003
3.3 µH, ±30%
1.0 A
2.8 x 2.8 x 1.1
Wuerth
PSI25201B-2R2MS
2.2 uH, ±20%
1.3 A
2.0 x 2.5 x 1.2
Cyntec
NR3015T-2R2M
2.2 uH, ±20%
1.5 A
3.0 x 3.0 x 1.5
Taiyo Yuden
BRC2012T2R2MD
2.2 µH, ±20%
1.0 A
2.0 x 1.25 x 1.4
Taiyo Yuden
BRC2012T3R3MD
3.3 µH, ±20%
0.87 A
2.0 x 1.25 x 1.4
Taiyo Yuden
IRMS at 40°C rise or ISAT at 30% drop.
TPS6217x can operate with an inductor as low as 2.2 µH. However, for applications running with low input
voltages, 3.3 µH is recommended, to allow the full output current. The inductor value also determines the load
current at which power save mode is entered:
I load ( PSM ) =
1
DI L
2
(9)
Using Equation 8, this current level is adjusted by changing the inductor value.
14
Submit Documentation Feedback
Copyright © 2011–2017, Texas Instruments Incorporated
Product Folder Links: TPS62170 TPS62171 TPS62172 TPS62173
TPS62170, TPS62171, TPS62172, TPS62173
www.ti.com
SLVSAT8E – NOVEMBER 2011 – REVISED MAY 2017
9.2.2.4 Capacitor Selection
9.2.2.4.1 Output Capacitor
The recommended value for the output capacitor is 22 µF. The architecture of the TPS6217x allows the use of
tiny ceramic output capacitors with low equivalent series resistance (ESR). These capacitors provide low output
voltage ripple and are recommended. To keep its low resistance up to high frequencies and to get narrow
capacitance variation with temperature, it is recommended to use an X7R or X5R dielectric. Using a higher value
can have some advantages like smaller voltage ripple and a tighter DC output accuracy in power save mode
(see SLVA463).
Note: In power save mode, the output voltage ripple depends on the output capacitance, its ESR and the peak
inductor current. Using ceramic capacitors provides small ESR and low ripple.
9.2.2.4.2 Input Capacitor
For most applications, 10 µF is sufficient and is recommended, though a larger value reduces input current ripple
further. The input capacitor buffers the input voltage for transient events and also decouples the converter from
the supply. A low ESR multilayer ceramic capacitor is recommended for best filtering and should be placed
between VIN and PGND as close as possible to those pins.
spacing
NOTE
DC bias effect: High capacitance ceramic capacitors have a DC bias effect, which has a
strong influence on the final effective capacitance. Therefore the right capacitor value has
to be chosen carefully. Package size and voltage rating in combination with dielectric
material are responsible for differences between the rated capacitor value and the
effective capacitance.
spacing
9.2.2.5 Output Filter and Loop Stability
The devices of the TPS6217x family are internally compensated to be stable with L-C filter combinations
corresponding to a corner frequency calculated with Equation 10:
space
f LC =
1
2p L × C
(10)
space
Proven nominal values for inductance and ceramic capacitance are given in Table 2 and are recommended for
use. Different values may work, but care has to be taken on the loop stability which is affected. More information
including a detailed L-C stability matrix is found in SLVA463.
The TPS6217x devices, both fixed and adjustable versions, include an internal 25 pF feed forward capacitor,
connected between the VOS and FB pins. This capacitor impacts the frequency behavior and sets a pole and
zero in the control loop with the resistors of the feedback divider, per Equation 11 and Equation 12:
space
f zero =
1
2p × R1 × 25 pF
(11)
space
f pole =
1
2p × 25 pF
æ 1
1 ö
÷÷
× çç
+
è R1 R 2 ø
(12)
space
Copyright © 2011–2017, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS62170 TPS62171 TPS62172 TPS62173
15
TPS62170, TPS62171, TPS62172, TPS62173
SLVSAT8E – NOVEMBER 2011 – REVISED MAY 2017
www.ti.com
Though the TPS6217x devices are stable without the pole and zero being in a particular location, adjusting their
location to the specific needs of the application can provide better performance in power save mode and/or
improved transient response. An external feed-forward capacitor can also be added. A more detailed discussion
on the optimization for stability vs. transient response can be found in SLVA289 and SLVA466.
If using ceramic capacitors, the DC bias effect has to be considered. The DC bias effect results in a drop in
effective capacitance as the voltage across the capacitor increases (see NOTE in Capacitor selection section).
9.2.2.6 TPS6216x Components List
Table 4 shows the list of components for the Application Curves.
Table 4. List of Components
REFERENCE
DESCRIPTION
MANUFACTURER
IC
17 V, 0.5A Step-Down Converter, WSON
TPS62170DSG, Texas Instruments
L1
2.2 uH, 1.4 A, 3 mm x 2.8 mm x 1.2 mm
VLF3012ST-2R2M1R4, TDK
C1
10 µF, 25 V, Ceramic, 0805
Standard
C2
22 µF, 6.3 V, Ceramic, 0805
Standard
R1
depending on VOUT
R2
depending on VOUT
R3
100 kΩ, Chip, 0603, 1/16 W, 1%
16
Submit Documentation Feedback
Standard
Copyright © 2011–2017, Texas Instruments Incorporated
Product Folder Links: TPS62170 TPS62171 TPS62172 TPS62173
TPS62170, TPS62171, TPS62172, TPS62173
www.ti.com
SLVSAT8E – NOVEMBER 2011 – REVISED MAY 2017
9.2.3 Application Curves
VIN = 12V, VOUT = 3.3V, TA=25°C, (unless otherwise noted)
100.0
100.0
90.0
90.0
80.0
70.0
VIN=17V
60.0
Efficiency (%)
Efficiency (%)
80.0
VIN=12V
50.0
40.0
30.0
VOUT=6.0V
L=2.2uH (VLF3012ST)
Cout=22uF
10.0
0.0
0.0001
0.001
0.01
Output Current (A)
0.1
10.0
0.0
1
90.0
9
10
11
12
13
Input Voltage (V)
14
15
16
17
G001
80.0
70.0
VIN=17V
60.0
Efficiency (%)
Efficiency (%)
8
Figure 9. Efficiency vs Input Voltage, VOUT = 6 V
80.0
VIN=12V
VIN=6V
40.0
30.0
70.0
IOUT=1mA
60.0
IOUT=100mA
IOUT=10mA
IOUT=0.5A
50.0
40.0
30.0
VOUT=5.0V
L=2.2uH (VLF3012ST)
Cout=22uF
20.0
10.0
0.001
0.01
Output Current (A)
0.1
10.0
0.0
1
7
8
9
10
G001
90.0
90.0
80.0
80.0
70.0
70.0
Efficiency (%)
100.0
60.0
11
12
13
Input Voltage (V)
14
15
16
17
G001
Figure 11. Efficiency vs Input Voltage, VOUT = 5 V
100.0
VIN=17V
50.0
VOUT=5.0V
L=2.2uH (VLF3012ST)
Cout=22uF
20.0
Figure 10. Efficiency vs Output Current, VOUT = 5 V
Efficiency (%)
7
G001
100.0
VIN=12V
VIN=5V
30.0
IOUT=500mA
IOUT=1mA
60.0
IOUT=10mA
IOUT=100mA
50.0
40.0
30.0
VOUT=3.3V
L=2.2uH (VLF3012ST)
Cout=22uF
20.0
10.0
0.0
0.0001
IOUT=500mA
VOUT=6.0V
L=2.2uH (VLF3012ST)
Cout=22uF
20.0
90.0
40.0
IOUT=10mA
40.0
100.0
0.0
0.0001
IOUT=100mA
50.0
Figure 8. Efficiency vs Output Current, VOUT = 6 V
50.0
IOUT=1mA
60.0
30.0
VIN=6V
20.0
70.0
0.001
0.01
Output Current (A)
0.1
10.0
1
Figure 12. Efficiency vs Output Current, VOUT = 3.3 V
Copyright © 2011–2017, Texas Instruments Incorporated
VOUT=3.3V
L=2.2uH (VLF3012ST)
Cout=22uF
20.0
G001
0.0
4
5
6
7
8
9 10 11 12 13 14 15 16 17
Input Voltage (V)
G001
Figure 13. Efficiency vs Input Voltage, VOUT = 3.3 V
Submit Documentation Feedback
Product Folder Links: TPS62170 TPS62171 TPS62172 TPS62173
17
TPS62170, TPS62171, TPS62172, TPS62173
SLVSAT8E – NOVEMBER 2011 – REVISED MAY 2017
www.ti.com
VIN = 12V, VOUT = 3.3V, TA=25°C, (unless otherwise noted)
100.0
80.0
80.0
70.0
70.0
60.0
VIN=17V
50.0
40.0
VIN=12V
30.0
VOUT=1.8V
L=2.2uH (VLF3012ST)
Cout=22uF
10.0
0.001
0.01
Output Current (A)
0.1
0.0
1
VOUT=1.8V
L=2.2uH (VLF3012ST)
Cout=22uF
3
4
5
6
7
8 9 10 11 12 13 14 15 16 17
Input Voltage (V)
G001
Figure 15. Efficiency vs Input Voltage, VOUT = 1.8 V
100.0
90.0
VIN=5V
70.0
60.0
50.0
VIN=17V
40.0
VIN=12V
30.0
20.0
10.0
60.0
50.0
IOUT=1mA
40.0
0.01
Output Current (A)
0.1
VOUT=0.9V
L=2.2uH (VLF3012ST)
Cout=22uF
10.0
0.0
1
3
4
5
6
G001
7
8 9 10 11 12 13 14 15 16 17
Input Voltage (V)
G001
Figure 17. Efficiency vs Input Voltage, VOUT = 0.9 V
3.35
Output Voltage (V)
3.35
3.30
VIN=5V
VIN=12V
VIN=17V
3.25
IOUT=1mA
IOUT=10mA
IOUT=100mA
IOUT=500mA
3.30
3.25
VOUT=3.3V
L=2.2uH (VLF3012ST)
Cout=22uF
0.001
0.01
Output Current (A)
0.1
VOUT=3.3V
L=2.2uH (VLF3012ST)
Cout=22uF
1
G001
Figure 18. Output Voltage Accuracy (Load Regulation)
18
IOUT=500mA
70.0
20.0
Figure 16. Efficiency vs Output Current, VOUT = 0.9 V
3.20
0.0001
IOUT=100mA
30.0
VOUT=0.9V
L=2.2uH (VLF3012ST)
Cout=22uF
0.001
IOUT=10mA
80.0
Efficiency (%)
Efficiency (%)
IOUT=100mA
G001
90.0
Output Voltage (V)
IOUT=10mA
40.0
10.0
100.0
0.0
0.0001
IOUT=1mA
50.0
20.0
Figure 14. Efficiency vs Output Current, VOUT = 1.8 V
80.0
60.0
30.0
20.0
0.0
0.0001
IOUT=500mA
90.0
Efficiency (%)
Efficiency (%)
90.0
100.0
VIN=5V
Submit Documentation Feedback
3.20
4
7
10
13
Input Voltage (V)
16
G001
Figure 19. Output Voltage Accuracy (Line Regulation)
Copyright © 2011–2017, Texas Instruments Incorporated
Product Folder Links: TPS62170 TPS62171 TPS62172 TPS62173
TPS62170, TPS62171, TPS62172, TPS62173
www.ti.com
SLVSAT8E – NOVEMBER 2011 – REVISED MAY 2017
4
4
3.5
3.5
Switching Frequency (MHz)
Switching Frequency (MHz)
VIN = 12V, VOUT = 3.3V, TA=25°C, (unless otherwise noted)
3
2.5
2
1.5
1
VIN=12V, VOUT=3.3V
L=2.2uH (VLF3012ST)
0.5
0
0
0.1
0.2
0.3
Output Current (A)
0.4
3
2.5
2
1
VOUT=3.3V
L=2.2uH (VLF3012ST)
Cout=22uF
0.5
0
0.5
4
6
8
10
12
Input Voltage (V)
G000
Figure 20. Switching Frequency vs Output Current
16
18
G000
1.5
VOUT=3.3V,
L=2.2uH (VLF3012ST)
Cout=22uF
1.2
VIN=17V
Output Current (A)
0.04
0.03
0.02
VIN=12V
0.01
1
−40°C
0.5
85°C
VOUT=3.3V
L=2.2uH (VLF3012ST)
Cout=22uF
0.2
0
0.1
0.2
0.3
Output Current (A)
0.4
0.5
G000
25°C
0.8
VIN=5V
0
14
Figure 21. Switching Frequency vs Input Voltage
0.05
Output Voltage Ripple (V)
IOUT=0.5A
1.5
0
4
5
6
7
8
9 10 11 12 13 14 15 16 17
Input Voltage (V)
G000
Figure 22. Output Voltage Ripple
Figure 23. Maximum Output Current
Figure 24. PWM to PSM Mode Transition
Figure 25. PSM to PWM Mode Transition
Copyright © 2011–2017, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS62170 TPS62171 TPS62172 TPS62173
19
TPS62170, TPS62171, TPS62172, TPS62173
SLVSAT8E – NOVEMBER 2011 – REVISED MAY 2017
www.ti.com
VIN = 12V, VOUT = 3.3V, TA=25°C, (unless otherwise noted)
20
Figure 26. Load Transient Response in PWM Mode
(200 mA to 500 mA)
Figure 27. Load Transient Response from
Power Save Mode (100 mA to 500 mA)
Figure 28. Load Transient Response in PWM Mode
(200 mA to 500 mA), Rising Edge
Figure 29. Load Transient Response in PWM Mode
(200 mA to 500 mA), Falling Edge
Figure 30. Startup with IOUT = 500 mA, VOUT = 3.3 V
Figure 31. Startup with IOUT = 500 mA, VOUT = 3.3 V
Submit Documentation Feedback
Copyright © 2011–2017, Texas Instruments Incorporated
Product Folder Links: TPS62170 TPS62171 TPS62172 TPS62173
TPS62170, TPS62171, TPS62172, TPS62173
www.ti.com
SLVSAT8E – NOVEMBER 2011 – REVISED MAY 2017
VIN = 12V, VOUT = 3.3V, TA=25°C, (unless otherwise noted)
Figure 32. Typical Operation in Power Save Mode
(IOUT = 66 mA)
Figure 33. Typical Operation in PWM mode (IOUT = 500 mA)
9.3 System Examples
Figure 34 through Figure 40 show various TPS6217x devices and input voltages that provide a 0.5-A power
supply with output voltage options.
(5 .. 17)V
5V / 0.5A
2.2µH
VIN
SW
EN
10uF
VOS
100k
TPS62173
AGND
PG
PGND
FB
22uF
Figure 34. 5-V and 0.5-A Power Supply
(3.3 .. 17)V
3.3V / 0.5A
2.2µH
VIN
SW
EN
10uF
VOS
TPS62172
AGND
PG
PGND
FB
100k
22uF
Figure 35. 3.3-V and 0.5-A Power Supply
Copyright © 2011–2017, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS62170 TPS62171 TPS62172 TPS62173
21
TPS62170, TPS62171, TPS62172, TPS62173
SLVSAT8E – NOVEMBER 2011 – REVISED MAY 2017
www.ti.com
System Examples (continued)
(3 .. 17)V
2.5V / 0.5A
2.2µH
VIN
SW
EN
10uF
VOS
PG
PGND
FB
390k
100k
TPS62170
AGND
22uF
180k
Figure 36. 2.5-V and 0.5-A Power Supply
(3 .. 17)V
1.8V / 0.5A
2.2µH
VIN
SW
EN
10uF
VOS
100k
TPS62171
AGND
PG
PGND
FB
22uF
Figure 37. 1.8-V and 0.5-A Power Supply
(3 .. 17)V
1.5V / 0.5A
2.2µH
VIN
SW
EN
10uF
VOS
TPS62170
AGND
PG
PGND
FB
100k
130k
22uF
150k
Figure 38. 1.5-V and 0.5-A Power Supply
22
Submit Documentation Feedback
Copyright © 2011–2017, Texas Instruments Incorporated
Product Folder Links: TPS62170 TPS62171 TPS62172 TPS62173
TPS62170, TPS62171, TPS62172, TPS62173
www.ti.com
SLVSAT8E – NOVEMBER 2011 – REVISED MAY 2017
System Examples (continued)
(3 .. 17)V
1.2V / 0.5A
2.2µH
VIN
SW
EN
10uF
VOS
100k
TPS62170
AGND
PG
PGND
FB
75k
22uF
150k
Figure 39. 1.2-V and 0.5-A Power Supply
(3 .. 17)V
1V / 0.5A
2.2µH
VIN
SW
EN
10uF
VOS
TPS62170
AGND
PG
PGND
FB
100k
51k
22uF
200k
Figure 40. 1-V and 0.5-A Power Supply
Copyright © 2011–2017, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS62170 TPS62171 TPS62172 TPS62173
23
TPS62170, TPS62171, TPS62172, TPS62173
SLVSAT8E – NOVEMBER 2011 – REVISED MAY 2017
www.ti.com
System Examples (continued)
9.3.1 Inverting Power Supply
The TPS6217x can be used as inverting power supply by rearranging external circuitry as shown in Figure 41.
As the former GND node now represents a voltage level below system ground, the voltage difference between
VIN and VOUT has to be limited for operation to the maximum supply voltage of 17 V (see Equation 13).
space
VIN + VOUT £ VIN max
(13)
space
10uF
2.2µH
(3 .. 12)V
VIN
SW
EN
10uF
VOS
TPS62170
AGND
PG
PGND
FB
100k
680k
22uF
130k
-5V
Figure 41. –5-V Inverting Power Supply
The transfer function of the inverting power supply configuration differs from the buck mode transfer function,
incorporating a right half plane zero additionally. The loop stability has to be adapted and an output capacitance
of at least 22 µF is recommended. A detailed design example is given in SLVA469.
10 Power Supply Recommendations
The TPS6217x device family has no special requirements for its input power supply. The input power supply's
output current needs to be rated according to the supply voltage, output voltage and output current of the
TPS6217x.
24
Submit Documentation Feedback
Copyright © 2011–2017, Texas Instruments Incorporated
Product Folder Links: TPS62170 TPS62171 TPS62172 TPS62173
TPS62170, TPS62171, TPS62172, TPS62173
www.ti.com
SLVSAT8E – NOVEMBER 2011 – REVISED MAY 2017
11 Layout
11.1 Layout Guidelines
A proper layout is critical for the operation of a switched mode power supply, even more at high switching
frequencies. Therefore the PCB layout of the TPS6217x demands careful attention to ensure operation and to
get the performance specified. A poor layout can lead to issues like poor regulation (both line and load), stability
and accuracy weaknesses, increased EMI radiation and noise sensitivity.
Provide low inductive and resistive paths to ground for loops with high di/dt. Therefore paths conducting the
switched load current should be as short and wide as possible. Provide low capacitive paths (with respect to all
other nodes) for wires with high dv/dt. Therefore the input and output capacitance should be placed as close as
possible to the IC pins and parallel wiring over long distances as well as narrow traces should be avoided. Loops
which conduct an alternating current should outline an area as small as possible, as this area is proportional to
the energy radiated.
Also sensitive nodes like FB and VOS should be connected with short wires, not nearby high dv/dt signals (such
as SW). As they carry information about the output voltage, they should be connected as close as possible to the
actual output voltage (at the output capacitor). Signals not assigned to power transmission (such as the feedback
divider) should refer to the signal ground (AGND) and always be separated from the power ground (PGND).
In summary, the input capacitor should be placed as close as possible to the VIN and PGND pin of the IC. This
connections should be done with wide and short traces. The output capacitor should be placed such that its
ground is as close as possible to the IC's PGND pins - avoiding additional voltage drop in traces. This connection
should also be made short and wide. The inductor should be placed close to the SW pin and connect directly to
the output capacitor - minimizing the loop area between the SW pin, inductor, output capacitor and PGND pin.
The feedback resistors, R1 and R2, should be placed close to the IC and connect directly to the AGND and FB
pins. Those connections (including VOUT) to the resistors and even more to the VOS pin should stay away from
noise sources, such as the inductor. The VOS pin should connect in the shortest way to VOUT at the output
capacitor, while the VOUT connection to the feedback divider can connect at the load.
A single point grounding scheme should be implemented with all grounds (AGND, PGND and the thermal pad)
connecting at the IC's exposed thermal pad. See Figure 42 for the recommended layout of the TPS6217x. More
detailed information can be found in the EVM Users Guide, SLVU483.
The exposed thermal pad must be soldered to the circuit board for mechanical reliability and to achieve
appropriate power dissipation. Although the exposed thermal pad can be connected to a floating circuit board
trace, the device has better thermal performance if it is connected to a larger ground plane. The exposed thermal
pad is electrically connected to AGND.
11.2 Layout Example
GND
VOUT
C2
L1
C1
PGND
PG
VIN
SW
EN
VOS
AGND
FB
AGND
VIN
R2
R1
Figure 42. Layout Example
Copyright © 2011–2017, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS62170 TPS62171 TPS62172 TPS62173
25
TPS62170, TPS62171, TPS62172, TPS62173
SLVSAT8E – NOVEMBER 2011 – REVISED MAY 2017
www.ti.com
11.3 Thermal Considerations
Implementation of integrated circuits in low-profile and fine-pitch surface-mount packages typically requires
special attention to power dissipation. Many system-dependent issues such as thermal coupling, airflow, added
heat sinks and convection surfaces, and the presence of other heat-generating components affect the powerdissipation limits of a given component.
Three basic approaches for enhancing thermal performance are listed below:
• Improving the power dissipation capability of the PCB design
• Improving the thermal coupling of the component to the PCB by soldering the exposed thermal pad
• Introducing airflow in the system
For more details on how to use the thermal parameters, see the application notes: Thermal Characteristics
Application Note SZZA017, and SPRA953.
The TPS6217x is designed for a maximum operating junction temperature (Tj) of 125°C. Therefore the maximum
output power is limited by the power losses that can be dissipated over the actual thermal resistance, given by
the package and the surrounding PCB structures. If the thermal resistance of the package is given, the size of
the surrounding copper area and a proper thermal connection of the IC can reduce the thermal resistance. To
get an improved thermal behavior, it is recommended to use top layer metal to connect the device with wide and
thick metal lines. Internal ground layers can connect to vias directly under the IC for improved thermal
performance.
If short circuit or overload conditions are present, the device is protected by limiting internal power dissipation.
26
Submit Documentation Feedback
Copyright © 2011–2017, Texas Instruments Incorporated
Product Folder Links: TPS62170 TPS62171 TPS62172 TPS62173
TPS62170, TPS62171, TPS62172, TPS62173
www.ti.com
SLVSAT8E – NOVEMBER 2011 – REVISED MAY 2017
12 Device and Documentation Support
12.1 Device Support
12.1.1 Third-Party Products Disclaimer
TI'S PUBLICATION OF INFORMATION REGARDING THIRD-PARTY PRODUCTS OR SERVICES DOES NOT
CONSTITUTE AN ENDORSEMENT REGARDING THE SUITABILITY OF SUCH PRODUCTS OR SERVICES
OR A WARRANTY, REPRESENTATION OR ENDORSEMENT OF SUCH PRODUCTS OR SERVICES, EITHER
ALONE OR IN COMBINATION WITH ANY TI PRODUCT OR SERVICE.
12.1.2 Development Support
12.1.2.1 Custom Design With WEBENCH® Tools
Click here to create a custom design using the TPS6217x device with the WEBENCH® Power Designer.
1. Start by entering the input voltage (VIN), output voltage (VOUT), and output current (IOUT) requirements.
2. Optimize the design for key parameters such as efficiency, footprint, and cost using the optimizer dial.
3. Compare the generated design with other possible solutions from Texas Instruments.
The WEBENCH Power Designer provides a customized schematic along with a list of materials with real-time
pricing and component availability.
In most cases, these actions are available:
• Run electrical simulations to see important waveforms and circuit performance
• Run thermal simulations to understand board thermal performance
• Export customized schematic and layout into popular CAD formats
• Print PDF reports for the design, and share the design with colleagues
Get more information about WEBENCH tools at www.ti.com/WEBENCH.
12.2 Documentation Support
12.2.1 Related Documentation
For related documentation see the following:
• TPS62160, 3V-17V 1A Step-Down Converters with DCS-Control™, TPS62160
• TPS62125, 3V-17V, 300mA Buck Converter With Adjustable Enable Threshold And Hysteresis, TPS62125
• Optimizing the TPS62130/40/50/60/70 Output Filter, SLVA463
• Optimizing Transient Response of Internally Compensated DC-DC Converters With Feedforward Capacitor,
SLVA289
• Using a Feedforward Capacitor to Improve Stability and Bandwidth of TPS62130/40/50/60/70, SLVA466
• Using the TPS6215x in an Inverting Buck-Boost Topology, SLVA469
• TPS62160EVM and TPS62170EVM-627 Evaluation Modules, SLVU483
• Thermal Characteristics of Linear and Logic Packages Using JEDEC PCB Designs, SZZA017
12.3 Related Links
The table below lists quick access links. Categories include technical documents, support and community
resources, tools and software, and quick access to sample or buy.
Table 5. Related Links
PARTS
PRODUCT FOLDER
SAMPLE & BUY
TECHNICAL
DOCUMENTS
TOOLS &
SOFTWARE
SUPPORT &
COMMUNITY
TPS62170
Click here
Click here
Click here
Click here
Click here
TPS62171
Click here
Click here
Click here
Click here
Click here
TPS62172
Click here
Click here
Click here
Click here
Click here
TPS62173
Click here
Click here
Click here
Click here
Click here
Copyright © 2011–2017, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TPS62170 TPS62171 TPS62172 TPS62173
27
TPS62170, TPS62171, TPS62172, TPS62173
SLVSAT8E – NOVEMBER 2011 – REVISED MAY 2017
www.ti.com
12.4 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
12.5 Trademarks
DCS-Control, E2E are trademarks of Texas Instruments.
WEBENCH is a registered trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
12.6 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
12.7 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
13 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
28
Submit Documentation Feedback
Copyright © 2011–2017, Texas Instruments Incorporated
Product Folder Links: TPS62170 TPS62171 TPS62172 TPS62173
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
PACKAGING INFORMATION
Orderable Device
Status
(1)
Package Type Package Pins Package
Drawing
Qty
Eco Plan
(2)
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
(3)
(4/5)
(6)
TPS62170DSGR
ACTIVE
WSON
DSG
8
3000
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 125
QUE
TPS62170DSGT
ACTIVE
WSON
DSG
8
250
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 125
QUE
TPS62171DSGR
ACTIVE
WSON
DSG
8
3000
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 125
QUF
TPS62171DSGT
ACTIVE
WSON
DSG
8
250
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 125
QUF
TPS62172DSGR
ACTIVE
WSON
DSG
8
3000
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 125
QUG
TPS62172DSGT
ACTIVE
WSON
DSG
8
250
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 125
QUG
TPS62173DSGR
ACTIVE
WSON
DSG
8
3000
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 125
QUH
TPS62173DSGT
ACTIVE
WSON
DSG
8
250
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
-40 to 125
QUH
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of
工商网监
湘ICP备2023018690号
