UC2714DP

UC1714/5 UC2714/5 UC3714/5 application INFO available Complementary Switch FET Drivers FEATURES DESCRIPTION • Single Input (PWM and TTL Compatible) • Time Delays Between Power and Auxiliary Outputs Independently Programmable from 50ns to 500ns These two families of high speed drivers are designed to provide drive waveforms for complementary switches. Complementary switch configurations are commonly used in synchronous rectification circuits and active clamp/reset circuits, which can provide zero voltage switching. In order to facilitate the soft switching transitions, independently programmable delays between the two output waveforms are provided on these drivers. The delay pins also have true zero voltage sensing capability which allows immediate activation of the corresponding switch when zero voltage is applied. These devices require a PWM-type input to operate and can be interfaced with commonly available PWM controllers. • Time Delay or True Zero-Voltage Operation Independently Configurable for Each Output In the UC1714 series, the AUX output is inverted to allow driving a p-channel MOSFET. In the UC1715 series, the two outputs are configured in a true complementary fashion. • High Current Power FET Driver, 1.0A Source/2A Sink • Auxiliary Output FET Driver, 0.5A Source/1A Sink • Switching Frequency to 1MHz • Typical 50ns Propagation Delays • ENBL Pin Activates 220µA Sleep Mode • Power Output is Active Low in Sleep Mode • Synchronous Rectifier Driver BLOCK DIAGRAM 2 PWR 50ns –500ns 4 AUX TIMER S Q 1 VCC 3 GND 50ns –500ns INPUT 6 TIMER S Q T1 7 R T2 UC1714 ONLY VREF 5 R VREF VCC 5V BIAS ENBL 3V GND LOGIC GATES TIMER REF 1.4V ENBL 8 ENABLE Note: Pin numbers refer to J, N and D packages. SLUS170A - FEBRUARY 1999 - REVISED JANUARY 2002 UDG-99028 UC1714/5 UC2714/5 UC3714/5 ABSOLUTE MAXIMUM RATINGS Input Voltage Range (INPUT, ENBL) . . . . . . . . . . −0.3V to 20V Storage Temperature Range . . . . . . . . . . . . . . −65°C to 150°C Operating Junction Temperature (Note 1) . . . . . . . . . . . . 150°C Lead Temperature (Soldering 10 seconds) . . . . . . . . . . . 300°C Supply Voltage VCC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20V Power Driver IOH continuous . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −200mA peak. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −1A Power Driver IOL continuous . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400mA peak. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2A Auxiliary Driver IOH continuous . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −100mA peak . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −500mA Auxiliary Driver IOL continuous . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200mA peak. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1A Note 1: Unless otherwise indicated, voltages are referenced to ground and currents are positive into, negative out of, the specified terminals. Note 2: Consult Packaging Section of databook for thermal limitations and specifications of packages. CONNECTION DIAGRAMS DIL-8, SOIC-8 (Top View) J or N, D Packages SOIC-16 (Top View) DP Package ELECTRICAL CHARACTERISTICS: Unless otherwise stated, VCC = 15V, ENBL ≥ 2V, RT1 = 100kΩ from T1 to GND, RT2 = 100kΩ from T2 to GND, and −55°C < TA < 125°C for the UC1714/5, −40°C < TA < 85°C for the UC2714/5, and 0°C < TA < 70°C for the UC3714/5, TA = TJ. PARAMETER TEST CONDITIONS MIN TYP MAX UNITS Overall 20 V ICC, nominal ENBL = 2.0V 7 18 24 mA ICC, sleep mode ENBL = 0.8V 200 300 µA Pre Turn-on PWR Output, Low VCC = 0V, IOUT = 10mA, ENBL  0.8V 0.3 1.6 V PWR Output Low, Sat. (VPWR) INPUT = 0.8V, IOUT = 40mA 0.3 0.8 V INPUT = 0.8V, IOUT = 400mA 2.1 2.8 V INPUT = 2.0V, IOUT = −20mA 2.1 3 V VCC Power Driver (PWR) PWR Output High, Sat. (VCC − VPWR) INPUT = 2.0V, IOUT = −200mA 2.3 3 V Rise Time CL = 2200pF 30 60 ns Fall Time CL = 2200pF 25 60 ns T1 Delay, AUX to PWR INPUT rising edge, RT1 = 10kΩ (Note 4) 20 35 80 ns T1 Delay, AUX to PWR INPUT rising edge, RT1 = 100kΩ (Note 4) 350 500 700 ns PWR Prop Delay INPUT falling edge, 50% (Note 3) 35 100 ns 2 UC1714/5 UC2714/5 UC3714/5 ELECTRICAL CHARACTERISTICS: Unless otherwise stated, VCC = 15V, ENBL ≥ 2V, RT1 = 100kΩ from T1 to GND, RT2 = 100kΩ from T2 to GND, and −55°C < TA < 125°C for the UC1714/5, −40°C < TA < 85°C for the UC2714/5, and 0°C < TA < 70°C for the UC3714/5, TA = TJ. PARAMETER TEST CONDITIONS MIN TYP MAX UNITS Auxiliary Driver (AUX) AUX Output Low, Sat (VAUX) VIN = 2.0V, IOUT = 20mA 0.3 0.8 V VIN = 2.0V, IOUT = 200mA 1.8 2.6 V VIN = 0.8V, IOUT = -10mA 2.1 3.0 V VIN = 0.8V, IOUT = -100mA 2.3 3.0 V Rise Time CL = 1000pF 45 60 ns Fall Time CL = 1000pF 30 60 ns AUX Output High, Sat (VCC – VAUX) T2 Delay, PWR to AUX INPUT falling edge, RT2 = 10kΩ (Note 4) 20 50 80 ns T2 Delay, PWR to AUX INPUT falling edge, RT2 = 100kΩ (Note 4) 250 350 550 ns AUX Prop Delay INPUT rising edge, 50% (Note 3) 35 80 ns Enable (ENBL) Input Threshold 1.2 2.0 V Input Current, IIH ENBL = 15V 0.8 1 10 µA Input Current, IIL ENBL = 0V −1 −10 µA −1.6 −2 mA 3 3.3 V 40 70 ns −1.2 −2 mA 3 3.3 V 50 100 ns T1 Current Limit T1 = 0V Nominal Voltage at T1 Minimum T1 Delay 2.7 T1 = 2.5V, (Note 4) T2 Current Limit T2 = 0V Nominal Voltage at T2 Minumum T2 Delay 2.7 T2 = 2.5V, (Note 4) Input (INPUT) Input Threshold 1.4 2.0 V Input Current, IIH INPUT = 15V 0.8 1 10 µA Input Current, IIL INPUT = 0V −5 −20 µA Note 3: Propagation delay times are measured from the 50% point of the input signal to the 10% point of the output signal’s transition with no load on outputs. Note 4: T1 delay is defined from the 50% point of the transition edge of AUX to the 10% of the rising edge of PWR. T2 delay is defined from the 90% of the falling edge of PWR to the 50% point of the transition edge of AUX. PIN DESCRIPTIONS The ENBL input will place the device into sleep mode when it is a logical low. The current into VCC during the sleep mode is typically 220µA. AUX: The AUX switches immediately at INPUT’s rising edge but waits through the T2 delay after INPUT’s falling edge before switching. AUX is capable of sourcing 0.5A and sinking 1.0A of drive current. See the Time Relationships diagram below for the difference between the UC1714 and UC1715 for INPUT, MAIN, and AUX. During sleep mode, AUX is inactive with a high impedance. GND: This is the reference pin for all input voltages and the return point for all device currents. It carries the full peak sinking current from the outputs. Any tendency for the outputs to ring below GND voltage must be damped or clamped such that GND remains the most negative potential. ENBL: The ENBL input switches at TTL logic levels (approximately 1.2V), and its input range is from 0V to 20V. 3 UC1714/5 UC2714/5 UC3714/5 PIN DESCRIPTIONS (cont.) INPUT: The input switches at TTL logic levels (approximately 1.4V) but the allowable range is from 0V to 20V, allowing direct connection to most common IC PWM controller outputs. The rising edge immediately switches the AUX output, and initiates a timing delay, T1, before switching on the PWR output. Similarly, the INPUT falling edge immediately turns off the PWR output and initiates a timing delay, T2, before switching the AUX output. T2: This pin functions in the same way as T1 but controls the time delay between PWR turn-off and activation of the AUX switch. T1, T2: The resistor on each of these pins sets the charging current on internal timing capacitors to provide independent time control. The nominal voltage level at each pin is 3V and the current is internally limited to 1mA. The total delay from INPUT to each output includes a propagation delay in addition to the programmable timer but since the propagation delays are approximately equal, the relative time delay between the two outputs can be assumed to be solely a function of the programmed delays. The relationship of the time delay vs. RT is shown in the Typical Characteristics curves. It should be noted that if the input signal comes from a controller with FET drive capability, this signal provides another option. INPUT and PWR provide a delay only at the leading edge while INPUT and AUX provide the delay at the trailing edge. PWR: The PWR output waits for the T1 delay after the INPUT’s rising edge before switching on, but switches off immediately at INPUT’s falling edge (neglecting propagation delays). This output is capable of sourcing 1A and sinking 2A of peak gate drive current. PWR output includes a passive, self-biased circuit which holds this pin active low, when ENBL ≥ 0.8V regardless of VCC’s voltage. Either or both pins can alternatively be used for voltage sensing in lieu of delay programming. This is done by pulling the timer pins below their nominal voltage level which immediately activates the timer output. VCC: The VCC input range is from 7V to 20V. This pin should be bypassed with a capacitor to GND consistent with peak load current demands. T1: A resistor to ground programs the time delay between AUX switch turn-off and PWR turn-on. TYPICAL CHARACTERISTICS INPUT PROPAGATION DELAYS PWR OUTPUT T1 vs RT1 T2 vs RT2 500 400 T2 DELAY DELAY (ns) T1 DELAY UC1714 AUX OUTPUT 300 200 100 0 UC1715 AUX OUTPUT 0 10 20 30 40 UDG-99027 Time relationships. (Notes 3, 4) T1 Delay, T2 Delay vs. RT 4 50 60 RT (kW) 70 80 90 100 UC1714/5 UC2714/5 UC3714/5 TYPICAL CHARACTERISTICS (cont.) 21 18 17 19 Icc (mA) Icc (mA) 20 18 16 17 16 15 0 100 200 300 400 500 600 700 800 900 1000 0 10 20 30 40 ICC vs Switching Frequency with No Load and 50% Duty Cycle RT1 = RT2 = 50k 70 80 90 100 75 100 600 RT1 = 100k 500 Deadband Delay (ns) 500 Deadband Delay (ns) 60 ICC vs RT with Opposite RT = 50k 600 400 300 RT1 = 50k 200 100 0 -75 50 RT (kΩ) Switching Frequency (kHz) 400 RT2 = 100k 300 RT2 = 50k 200 100 RT1 = 10k RT1 < 6k -50 -25 0 25 50 Temperature (°C) 75 100 0 -75 125 RT2 = 10k RT2 < 6k -50 -25 0 25 50 125 Temperature (°C) T1 Deadband vs. Temperature AUX to PWR T2 Deadband vs. Temperature PWR to AUX TYPICAL APPLICATIONS UDG-94011 Figure 1. Typical application with timed delays. UDG-94012 Figure 2. Using the timer input for zero-voltage sensing. 5 UC1714/5 UC2714/5 UC3714/5 TYPICAL APPLICATIONS (cont.) UDG-94013 Figure 3. Self-actuated sleep mode with the absence of an input PWM signal. Wake up occurs with the first pulse while turn-off is determined by the (RTO CTO) time constant. UDG-94015-2 Figure 4. Using the UC1715 as a complementary synchronous rectifier switch driver with n-channel FETs UDG-94014-1 Figure 5. Synchronous rectifier application with a charge pump to drive the high-side n-channel buck switch. VIN is limited to 10V as VCC will rise to approximately 2VIN. 6 UC1714/5 UC2714/5 UC3714/5 TYPICAL APPLICATIONS (cont.) UDG-94016-1 Figure 6. Typical forward converter topology with active reset provided by the UC1714 driving an N-channel switch (Q1) and a P-channel auxilliary switch (Q2). UDG-94017-1 Figure 7. Using an N-channel active reset switch with a floating drive command. 7 PACKAGE OPTION ADDENDUM www.ti.com 27-Jun-2011 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) (Requires Login) UC1714J OBSOLETE CDIP J 8 TBD Call TI Call TI UC1715J OBSOLETE CDIP J 8 TBD Call TI Call TI UC1715J883B OBSOLETE CDIP J 8 Call TI Call TI UC2714D ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-250C-1 YEAR UC2714DG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-250C-1 YEAR UC2714DTR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-250C-1 YEAR UC2714DTRG4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-250C-1 YEAR TBD TBD UC2714J OBSOLETE CDIP J 8 UC2714N ACTIVE PDIP P 8 50 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type UC2714NG4 ACTIVE PDIP P 8 50 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type UC2715D ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-250C-1 YEAR UC2715DG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-250C-1 YEAR UC2715DP ACTIVE SOIC D 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UC2715DPG4 ACTIVE SOIC D 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UC2715DTR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UC2715DTRG4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UC2715N ACTIVE PDIP P 8 50 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type UC2715NG4 ACTIVE PDIP P 8 50 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type Addendum-Page 1 Call TI Samples Call TI PACKAGE OPTION ADDENDUM www.ti.com 27-Jun-2011 Orderable Device Status (1) Package Type Package Drawing Pins Package Qty Eco Plan (2) Lead/ Ball Finish MSL Peak Temp (3) UC3714D ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-250C-1 YEAR UC3714DG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-250C-1 YEAR UC3714DP ACTIVE SOIC D 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UC3714DPG4 ACTIVE SOIC D 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UC3714DTR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-250C-1 YEAR UC3714DTRG4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-250C-1 YEAR UC3714N ACTIVE PDIP P 8 50 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type UC3714NG4 ACTIVE PDIP P 8 50 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type UC3715D ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UC3715DG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UC3715DP ACTIVE SOIC D 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UC3715DPG4 ACTIVE SOIC D 16 40 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR UC3715DTR ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-250C-1 YEAR UC3715DTRG4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-250C-1 YEAR UC3715N ACTIVE PDIP P 8 50 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type UC3715NG4 ACTIVE PDIP P 8 50 Green (RoHS & no Sb/Br) CU NIPDAU N / A for Pkg Type (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. Addendum-Page 2 Samples (Requires Login) PACKAGE OPTION ADDENDUM www.ti.com 27-Jun-2011 PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF UC1714, UC1715, UC2714, UC2714M, UC3714, UC3715 : • Catalog: UC3714, UC3715, UC2714 • Military: UC2714M, UC1714, UC1715 NOTE: Qualified Version Definitions: • Catalog - TI's standard catalog product • Military - QML certified for Military and Defense Applications Addendum-Page 3 PACKAGE MATERIALS INFORMATION www.ti.com 29-Jul-2008 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel Diameter Width (mm) W1 (mm) A0 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant UC2714DTR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 UC2715DTR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 UC3714DTR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 UC3715DTR SOIC D 8 2500 330.0 12.4 6.4 5.2 2.1 8.0 12.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 29-Jul-2008 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) UC2714DTR SOIC D 8 2500 346.0 346.0 29.0 UC2715DTR SOIC D 8 2500 346.0 346.0 29.0 UC3714DTR SOIC D 8 2500 346.0 346.0 29.0 UC3715DTR SOIC D 8 2500 346.0 346.0 29.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP® Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com Wireless www.ti.com/wireless-apps RF/IF and ZigBee® Solutions www.ti.com/lprf TI E2E Community Home Page e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2011, Texas Instruments Incorporated