PS9814-2-V-F4

NEC's HIGH CMR , 10 Mbps OPEN COLLECTOR PS9814-1,-2 OUTPUT TYPE 8-PIN SSOP (SO-8) HIGH-SPEED OPTOCOUPLER DESCRIPTION NEC's PS9814-1 and PS9814-2 are active-low type highspeed optocouplers that use a GaAlAs light-emitting diode on the input side and a photodetector IC that includes a photodiode and a signal processor on the same chip on the output side. The PS9814-1, -2 are designed specifically for high common mode transient immunity (CMR) and low pulse width distortion, the PS9814-2 is suitable for high density applications. 8 7 1 2 3 4 8 7 PIN CONNECTION (Top View) PS9814-1 65 1. NC 2. Anode 3. Cathode 4. NC 5. GND 6. VO 7. NC 8. VCC PS9814-2 65 • 40% REDUCTION OF MOUNTING AREA: 5-pin SOP × 2 • HIGH COMMON MODE TRANSIENT IMMUNITY: CMH, CML = ±20 kV/μs TYP. • PULSE WIDTH DISTORTION: | tPHL−tPLH | = 3 ns TYP. • HIGH-SPEED: 10 Mbps • HIGH ISOLATION VOLTAGE: BV = 2 500 Vr.m.s. • OPEN COLLECTOR OUTPUT • ORDERING NUMBER OF TAPE PRODUCT: PS9814-1-F3, F4: 1 500 pcs/reel PS9814-2-F3, F4: 1 500 pcs/reel • Pb-FREE PRODUCT • SAFETY STANDARDS: UL approved: File No. E72422 DIN EN60747-5-2 (VDE0884 Part2) approved No.40008347 (option) 1 2 SHIELD 3 4 TRUTH TABLE LED ON OFF OUTPUT L H APPLICATIONS • Measurement Equipment • PDP • Industrial Automation The information in this document is subject to change without notice. Before using this document, please confirm that this is the latest version. California Eastern Laboratories 1 SHIELD FEATURES 1. Anode1 2. Cathode1 3. Cathode2 4. Anode2 5. GND 6. VO2 7. VO1 8. VCC PS9814-1,-2 PACKAGE DIMENSIONS (UNIT: mm) 5.21±0.25 6.0±0.2 3.95±0.1 3.27±0.2 0.15 +0.10 -0.05 0.1±0.1 1.27 0.4 +0.10 -0.05 0.25 M 0.5±0.3 0.10 S MARKING EXAMPLES PS9814-1 PS9814-2 N 9814-1 NL251 N L 2 51 Assembly Lot N 9814-2 NL251 N L 2 51 Assembly Lot No. 1 pin Mark Initial of NEC (Engraved mark) Week Assembled Year Assembled (Last 1 Digit) No. 1 pin Mark Initial of NEC (Engraved mark) Week Assembled Year Assembled (Last 1 Digit) In-house Code (L: Pb-Free) Rank Code In-house Code (L: Pb-Free) Rank Code 2 PS9814-1,-2 ORDERING INFORMATION PART NUMBER PS9814-1 PS9814-1-F3 PS9814-1-F4 PS9814-2 PS9814-2-F3 PS9814-2-F4 PS9814-1-V PS9814-1-V-F3 PS9814-1-V-F4 PS9814-2-V PS9814-2-V-F3 PS9814-2-V-F4 ORDER NUMBER PS9814-1-A PS9814-1-F3-A PS9814-1-F4-A PS9814-2-A PS9814-2-F3-A PS9814-2-F4-A PS9814-1-V-A PS9814-1-V-F3-A PS9814-1-V-F4-A PS9814-2-V-A PS9814-2-V-F3-A PS9814-2-V-F4-A 20 pcs (Tape 20 pcs cut) Embossed Tape 1 500 pcs/reel 20 pcs (Tape 20 pcs cut) Embossed Tape 1 500 pcs/reel DIN EN60747-5-2 (VDE0884 Part2) Approved (Option) PS9814-2 PS9814-1 20 pcs (Tape 20 pcs cut) Embossed Tape 1 500 pcs/reel PS9814-2 SOLDER PLATING SPECIFICATION Pb-Free*2 PACKING STYLE 20 pcs (Tape 20 pcs cut) Embossed Tape 1 500 pcs/reel SAFETY STANDARD APPROVAL Standard products (UL approved) APPLICATION PART NUMBER*1 PS9814-1 *1 For the application of the Safety Standard, following part number should be used. *2 With regards to terminal solder (the solder contains lead) plated products (conventionally plated), contact your nearby sales office. 3 PS9814-1,-2 ABSOLUTE MAXIMUM RATINGS (TA = 25°C, unless otherwise specified) PARAMETER Diode Detector Forward Current Reverse Voltage Supply Voltage Output Voltage Output Current Power Dissipation*3 Isolation Voltage*4 Operating Ambient Temperature Storage Temperature SYMBOL IF VR VCC VO IO PC BV TA Tstg 20*1 5 7 7 25 40 2 500 –40 to +85 –55 to +125 RATINGS PS9814-1 PS9814-2 15*2 mA V/ch V V/ch mA/ch mW/ch Vr.m.s. °C °C UNIT *1 Reduced to 0.3 mA/°C at TA = 60°C or more. *2 Reduced to 0.1 mA/°C at TA = 60°C or more. *3 Applies to output pin VO. Reduced to 1.5 mW/°C at TA = 65°C or more. *4 AC voltage for 1 minute at TA = 25°C, RH = 60% between input and output. RECOMMENDED OPERATING CONDITIONS PARAMETER Low Level Input Voltage High Level Input Current Supply Voltage Pull-up Resistance TLL (RL = 1 kΩ, loads) SYMBOL VFL IFH VCC RL N MIN. 0 6.3 4.5 330 10 5.0 TYP. MAX. 0.8 12.5 5.5 4k 5 UNIT V mA V Ω 4 PS9814-1,-2 ELECTRICAL CHARACTERISTICS PARAMETER Diode Forward Voltage Reverse Current Terminal Capacitance Detector High Level Output Current Low Level Output Voltage*2 High Level Supply Current (PS9814-1) High Level Supply Current (PS9814-2) Low Level Supply Current (PS9814-1) Low Level Supply Current (PS9814-2) Coupled Threshold Input Current (H → L) Input-Output Isolation Resistance Insulation Resistance (Input-Input), (PS9814-2) Input-Output Isolation Capacitance Insulation Capacitance (Input-Input), (PS9814-2) Propagation Delay Time (H → L)*3 Propagation Delay Time (L → H)*3 Rise Time Fall Time Pulse Width Distortion (PWD) *3 Propagation Delay Skew Common Mode Transient Immunity at High Level Output*4 Common Mode Transient Immunity at Low Level Output*4 tr tf | tPHL−tPLH | tPSK CMH tPLH RI-O RI-I CI-O CI-I tPHL TA = 25°C VCC = 5 V, RL = 350 Ω, IF = 7.5 mA TA = 25°C VCC = 5 V, RL = 350 Ω, IF = 7.5 mA VCC = 5 V, RL = 350 Ω, IF = 7.5 mA VCC = 5 V, RL = 350 Ω, IF = 7.5 mA VCC = 5 V, RL = 350 Ω, IF = 7.5 mA VCC = 5 V, RL = 350 Ω, IF = 7.5 mA VCC = 5 V, RL = 350 Ω, TA = 25°C, IF = 0 mA, VO > 2 V, VCM = 1 kV VCC = 5 V, RL = 350 Ω, TA = 25°C, IF = 7.5 mA, VO < 0.8 V, VCM = 1 kV 10 20 20 10 3 50 60 kV/μs 51 VI-O = 1 kVDC, RH = 40 to 60%, TA = 25°C VI-I = 1 kVDC, RH = 40 to 60%, TA = 25°C V = 0 V, f = 1 MHz, TA = 25°C 1011 1010 0.6 0.3 54 75 100 75 100 ns pF Ω IFHL VCC = 5 V, VO = 0.8 V, RL = 350 Ω ICCL VCC = 5.5 V , IF = 10 mA, VO = open SYMBOL VF IR Ct IOH VOL ICCH (TA = -40 to +85ºC, unless otherwise specified) CONDITIONS IF = 10 mA, TA = 25°C VR = 3 V, TA = 25°C V = 0 V, f = 1 MHz, TA = 25°C VCC = VO = 5.5 V, VF = 0.8 V VCC = 5.5 V, IF = 5 mA, IOL = 13 mA VCC = 5.5 V , IF = 0 mA, VO = open 30 0.02 0.15 3 6 7.0 14 2 250 0.6 8 15 11 21 5 mA MIN. 1.4 TYP. *1 1.65 MAX. 1.8 10 UNIT V μA pF μA V mA CML 10 20 *1 Typical values at TA = 25°C *2 Because VOL of 2 V or more may be output when LED current input and when output supply of VCC = 2.6 V or less, it is important to confirm the characteristics (operation with the power supply on and off) during design, before using this device. 5 PS9814-1,-2 *3 Test circuit for propagation delay time PS9814-1 (PW = 1µs, Pulse input (IF) Duty cycle = 1/10) Input (Monitor) VCC = 5 V 0.1 µ F RL = 350 Ω VO (Monitor) CL = 15 pF Input (IF = 7.5 mA) 50% 47 Ω (PW = 1µs, Pulse input (IF) Duty cycle = 1/10) Input (Monitor) 47 Ω PS9814-2 VCC = 5 V RL = 350 Ω VO (Monitor) 0.1 µF CL = 15 pF Output tPHL tPLH 1.5 V VOL SHIELD SHIELD Remark CL includes probe and stray wiring capacitance. *4 Test circuit for common mode transient immunity SW IF PS9814-1 VCC = 5 V 0.1 µF RL = 350 Ω VO (Monitor) CL = 15 pF VCM 90% 10% tr VO (IF = 0 mA) VO (IF = 7.5 mA) tf 2V VOH 1 kV 0V VCM PS9814-2 VCC = 5 V RL = 350 Ω SHIELD SW IF 0.1 µF VO (Monitor) CL = 15 pF 0.8 V VOL SHIELD VCM USAGE CAUTIONS 1. This product is weak for static electricity by designed with high-speed integrated circuit so protect against static electricity when handling. 2. By-pass capacitor of 0.1 μF is used between VCC and GND near device. Also, ensure that the distance between the leads of the photocoupler and capacitor is no more than 10 mm. 3. Avoid storage at a high temperature and high humidity. 6 PS9814-1,-2 TYPICAL CHARACTERISTICS (TA = 25ºC, unless otherwise specified) MAXIMUM FORWARD CURRENT vs. AMBIENT TEMPERATURE 25 20 15 10 5 0 20 40 60 80 85 100 PS9814-1 PS9814-2 Detector Power Dissipation PC (mW) 30 Maximum Forward Current IF (mA) 50 40 30 20 10 DETECTOR POWER DISSIPATION vs. AMBIENT TEMPERATURE 0 20 40 60 80 85 100 Ambient Temperature TA (ºC) Ambient Temperature TA (ºC) FORWARD CURRENT vs. FORWARD VOLTAGE High Level Supply Current ICCH (mA) Low Level Supply Current ICCL (mA) 100 16 14 12 10 8 6 4 2 0 -50 SUPPLY CURRENT vs. AMBIENT TEMPERATURE ICCL (IF = 10 mA), PS9814-2 Forward Current IF (mA) 10 TA = +85ºC +50ºC +25ºC 0ºC -25ºC 1 ICCL (IF = 10 mA), PS9814-1 ICCH (IF = 0 mA), PS9814-2 ICCH (IF = 0 mA), PS9814-1 -25 0 25 50 75 100 0.1 0.01 1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 Forward Voltage VF (V) Ambient Temperature TA (ºC) OUTPUT VOLTAGE vs. INPUT CURRENT 6 5 Output Voltage VO (V) 4 3 2 1 0 1 2 3 4 5 6 Low Level Output Voltage VOL (V) VCC = 5.0 V, TA = 25ºC RL = 350 Ω 1.0 kΩ 4.0 kΩ, 4.7 kΩ 0.6 0.5 0.4 0.3 0.2 0.1 LOW LEVEL OUTPUT VOLTAGE vs. AMBIENT TEMPERATURE IF = 5.0 mA, VCC = 5.5 V IOL = 16.0 mA 13.0 mA 10.0 mA 6.0 mA 0 -50 -25 0 25 50 75 100 Input Current IF (mA) Ambient Temperature TA (ºC) 7 PS9814-1,-2 THRESHOLD INPUT CURRENT vs. AMBIENT TEMPERATURE Threshold Input Current IFHL (mA) VCC = 5.0 V, VO = 0.6 V Propagation Delay Time tPHL, tPLH (ns) 5 4 3 2 1 0 -50 RL = 350 Ω 1.0 kΩ 4.7 kΩ, 4.0 kΩ -25 0 25 50 75 100 Ambient Temperature TA (ºC) 100 80 60 40 20 0 -50 PROPAGATION DELAY TIME vs. AMBIENT TEMPERATURE IF = 7.5 mA, VCC = 5.0 V tPLH: RL = 1.0 kΩ tPLH: RL = 350 Ω tPHL: RL = 350 Ω, 1.0 kΩ -25 0 25 50 75 100 Ambient Temperature TA (ºC) PROPAGATION DELAY TIME vs. AMBIENT TEMPERATURE Propagation Delay Time tPHL, tPLH (ns) Pulse Width Distortion tPHLñtPLH (ns) 120 100 80 60 40 20 0 -50 -25 0 25 50 75 100 IF = 7.5 mA, VCC = 5.0 V tPLH: RL = 4.7 kΩ 60 50 40 30 20 10 0 -50 PULSE WIDTH DISTORTION vs. AMBIENT TEMPERATURE IF = 7.5 mA, VCC = 5.0 V RL = 4.7 kΩ 4.0 kΩ tPLH: RL = 4.0 kΩ tPHL: RL = 4.7 kΩ tPHL: RL = 4.0 kΩ RL = 350 Ω 1.0 kΩ -25 0 25 50 75 100 Ambient Temperature TA (ºC) Ambient Temperature TA (ºC) SWITCHING TIME vs. AMBIENT TEMPERATURE tr: RL = 4.0 kΩ, 4.7 kΩ Propagation Delay Time tPHL, tPLH (ns) 400 IF = 7.5 mA, VCC = 5.0 V 120 100 80 60 40 20 0 5 PROPAGATION DELAY TIME vs. INPUT CURRENT Switching Time tr, tf (ns) 300 tPLH: RL = 4.0 kΩ 200 tr: RL = 1.0 kΩ tr: RL = 350 Ω tf: RL = 350 Ω, 1.0 kΩ, 4.0 kΩ, 4.7 kΩ 100 tPLH: RL = 1.0 kΩ tPLH: RL = 350 Ω tPHL: RL = 350 Ω, 1.0 kΩ, 4.0 kΩ 7 9 11 0 -50 VCC = 5.0 V, TA = 25ºC 13 15 -25 0 25 50 75 100 Ambient Temperature TA (ºC) Input Current IF (mA) Remark The graphs indicate nominal characteristics. 8 PS9814-1,-2 TAPING SPECIFICATIONS (Units in mm) Outline and Dimensions (Tape) 5.56±0.1 2.0±0.05 4.0±0.1 1.75±0.1 1.5+0.1 -0 4.05 MAX. 1.7±0.1 8.0±0.1 12.0±0.2 5.5±0.1 6.4±0.1 3.6±0.1 0.3±0.05 Taping Direction PS9814-1-F3 PS9814-2-F3 PS9814-1-F4 PS9814-2-F4 Outline and Dimensions (Reel) 2.0±0.5 2.0±0.5 φ13.0±0.2 R 1.0 φ 21.0±0.8 φ 330±2.0 φ 13.0±0.2 φ 100±1.0 13.5±1.0 17.5±1.0 Packing: 1,500 pcs/reel 11.9 to 15.4 Outer edge of flange Remark The graphs indicate nominal characteristics. 9 PS9814-1,-2 RECOMMENDED MOUNT PAD DIMENSIONS (UNIT:mm) 1.45 0.8 5.25 10 1.27 PS9814-1,-2 NOTES ON HANDLING 1. Recommended soldering conditions (1) Infrared reflow soldering • Peak reflow temperature • Time of peak reflow temperature • Time of temperature higher than 220°C • Time to preheat temperature from 120 to 180°C • Number of reflows • Flux 260°C or below (package surface temperature) 10 seconds or less 60 seconds or less 120±30 s Three Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.) Recommended Temperature Profile of Infrared Reflow Package Surface Temperature T (ºC) (heating) to 10 s 260ºC MAX. 220ºC to 60 s 180ºC 120ºC 120±30 s (preheating) Time (s) (2) Wave soldering • Temperature • Time • Preheating conditions • Number of times • Flux 260°C or below (molten solder temperature) 10 seconds or less 120°C or below (package surface temperature) One (Allowed to be dipped in solder including plastic mold portion.) Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.) (3) Soldering by soldering iron • Peak temperature (lead part temperature) • Time (each pins) • Flux 350°C or below 3 seconds or less Rosin flux containing small amount of chlorine (The flux with a maximum chlorine content of 0.2 Wt% is recommended.) (a) Soldering of leads should be made at the point 1.5 to 2.0 mm from the root of the lead. (b) Please be sure that the temperature of the package would not be heated over 100°C. 11 PS9814-1,-2 (4) Cautions • Fluxes Avoid removing the residual flux with freon-based and chlorine-based cleaning solvent. 2. Cautions regarding noise Be aware that when voltage is applied suddenly between the photocoupler’s input and output or between collector-emitters at startup, the output transistor may enter the on state, even if the voltage is within the absolute maximum ratings. USAGE CAUTIONS 1. Protect against static electricity when handling. 2. Avoid storage at a high temperature and high humidity. Life Support Applications These NEC products are not intended for use in life support devices, appliances, or systems where the malfunction of these products can reasonably be expected to result in personal injury. The customers of CEL using or selling these products for use in such applications do so at their own risk and agree to fully indemnify CEL for all damages resulting from such improper use or sale. 02/07/2005 A Business Partner of NEC Compound Semiconductor Devices, Ltd. 12