UPG2160T5K-E2-A

GaAs INTEGRATED CIRCUIT µPG2160T5K L, S-BAND SINGLE CONTROL SPDT SWITCH DESCRIPTION The µPG2160T5K is a GaAs MMIC for L, S-band SPDT (Single Pole Double Throw) switch which was developed for mobile phone and other L, S-band applications. This device can operate frequency from 0.5 to 3.0 GHz, with low insertion loss and high isolation. This device is housed in a 6-pin plastic TSSON (Thin Shrink Small Out-line Non-leaded) package, and is suitable for high-density surface mounting. FEATURES • Supply voltage • Switch control voltage • : VDD = 2.4 to 2.8 V (2.6 V TYP.) : Vcont (H) = 2.4 to VDD (2.6 V TYP.) : Vcont (L) = −0.2 to 0.2 V (0 V TYP.) Low insertion loss : Lins1 = 0.30 dB TYP. @ f = 0.5 to 1.0 GHz, VDD = 2.6 V, Vcont (H) = 2.6 V, Vcont (L) = 0 V : Lins2 = 0.35 dB TYP. @ f = 1.0 to 2.0 GHz, VDD = 2.6 V, Vcont (H) = 2.6 V, Vcont (L) = 0 V : Lins3 = 0.40 dB TYP. @ f = 2.0 to 2.5 GHz, VDD = 2.6 V, Vcont (H) = 2.6 V, Vcont (L) = 0 V : Lins4 = 0.50 dB TYP. @ f = 2.5 to 3.0 GHz, VDD = 2.6 V, Vcont (H) = 2.6 V, Vcont (L) = 0 V High isolation : ISL1 = 25 dB TYP. @ f = 0.5 to 1.0 GHz, VDD = 2.6 V, Vcont (H) = 2.6 V, Vcont (L) = 0 V : ISL2 = 18 dB TYP. @ f = 1.0 to 2.0 GHz, VDD = 2.6 V, Vcont (H) = 2.6 V, Vcont (L) = 0 V : ISL3 = 17 dB TYP. @ f = 2.0 to 2.5 GHz, VDD = 2.6 V, Vcont (H) = 2.6 V, Vcont (L) = 0 V : ISL4 = 13 dB TYP. @ f = 2.5 to 3.0 GHz, VDD = 2.6 V, Vcont (H) = 2.6 V, Vcont (L) = 0 V Handling power : Pin (0.1 dB) = +21.0 dBm TYP. @ f = 2.0/2.5 GHz, VDD = 2.6 V, Vcont (H) = 2.6 V, Vcont (L) = 0 V High-density surface mounting : 6-pin plastic TSSON package (1.0 × 1.0 × 0.37 mm) • • • APPLICATIONS • L, S-band digital cellular or cordless telephone TM • W-LAN, WLL and Bluetooth etc. ORDERING INFORMATION Part Number Order Number Package 6-pin plastic TSSON (Pb-Free) Note Marking G4 Supplying Form • Embossed tape 8 mm wide • Pin 1, 6 face the perforation side of the tape • Qty 5 kpcs/reel µPG2160T5K-E2 µPG2160T5K-E2-A Note With regards to terminal solder (the solder contains lead) plated products (conventionally plated), contact your nearby sales office. Remark To order evaluation samples, contact your nearby sales office. Part number for sample order: µPG2160T5K-A Caution Observe precautions when handling because these devices are sensitive to electrostatic discharge. Document No. PG10635EJ01V0DS (1st edition) Date Published September 2006 NS CP(K) 2006 µPG2160T5K PIN CONNECTIONS AND INTERNAL BLOCK DIAGRAM (Top View) 1 6 (Top View) 1 6 6 (Bottom View) 1 Pin No. 1 2 3 Pin Name OUTPUT1 GND OUTPUT2 Vcont INPUT VDD G4 Vcont High Low Parameter Parameter Note 2 5 2 5 5 2 4 5 6 3 4 3 4 4 3 TRUTH TABLE INPUT−OUTPUT1 OFF ON INPUT−OUTPUT2 ON OFF ABSOLUTE MAXIMUM RATINGS (TA = +25°C, unless otherw ise specified) Symbol VDD Vcont Pin TA Tstg Ratings +6.0 +6.0 +26 −45 to +85 −55 to +135 Unit V V dBm °C °C Supply Voltage Switch Control Voltage Input Power Operating Ambient Temperature Storage Temperature RECOMMENDED OPERATING RANGE (TA = +25°C, unless otherw ise specified) Symbol VDD Note MIN. 2.4 2.4 − 0.2 TYP. 2.6 2.6 0 MAX. 2.8 VDD 0.2 Unit V V V Supply Voltage Switch Control Voltage (H) Switch Control Voltage (L) Vcont (H) Vcont (L) Note Vcont (H) ≤ VDD 2 Data Sheet PG10635EJ01V0DS µPG2160T5K ELECTRICAL CHARACTERISTICS (TA = +25°C, VDD = 2.6 V, Vcont (H) = 2.6 V, Vcont (L) = 0 V, DC cut capacitors = 56 pF, unless otherwise specified) Parameter Insertion Loss 1 Insertion Loss 2 Insertion Loss 3 Insertion Loss 4 Isolation 1 Isolation 2 Isolation 3 Isolation 4 Input Return Loss Output Return Loss 0.1 dB Loss Compression Input Power Note Symbol Lins1 Lins2 Lins3 Lins4 ISL1 ISL2 ISL3 ISL4 RLin RLout Pin (0.1 dB) Test Conditions f = 0.5 to 1.0 GHz f = 1.0 to 2.0 GHz f = 2.0 to 2.5 GHz f = 2.5 to 3.0 GHz f = 0.5 to 1.0 GHz f = 1.0 to 2.0 GHz f = 2.0 to 2.5 GHz f = 2.5 to 3.0 GHz f = 0.5 to 3.0 GHz f = 0.5 to 3.0 GHz f = 2.0/2.5 GHz MIN. − − − − 22 15 14 10 15 15 +18.0 TYP. 0.30 0.35 0.40 0.50 25 18 17 13 20 20 +21.0 MAX. 0.45 0.50 0.55 0.65 − − − − − − − − − 100 20 − Unit dB dB dB dB dBm 2nd Harmonics 3rd Harmonics Supply Current Switch Control Current Switch Control Speed 2f0 3 f0 IDD Icont tSW f = 2.0/2.5 GHz, Pin = +10 dBm f = 2.0/2.5 GHz, Pin = +10 dBm No signal 65 65 − − 75 75 50 4 150 dBc dBc µA µA ns 50% CTL to 90/10% RF − Note Pin (0.1 dB) is measured the input power level when the insertion loss increases more 0.1 dB than that of linear range. Caution This device is used it is necessary to use DC cut capacitors. Data Sheet PG10635EJ01V0DS 3 µPG2160T5K EVALUATION CIRCUIT VDD INPUT Vcont 1 000 pF C0 1 000 pF 6 5 4 1 2 3 C0 C0 OUTPUT1 OUTPUT2 Remark C0 : 56 pF The application circuits and their parameters are for reference only and are not intended for use in actual design-ins. 4 Data Sheet PG10635EJ01V0DS µPG2160T5K ILLUSTRATION OF THE TEST CIRCUIT ASSEMBLED ON EVALUATION BOARD Vcont OUTPUT2 C 5 INPUT C1 G4 C 4 C C 3 2 OUTPUT1 VDD USING THE NEC EVALUATION BOARD Symbol C1, C2, C3 C4, C5 Values 56 pF 1 000 pF Data Sheet PG10635EJ01V0DS 5 µPG2160T5K TYPICAL CHARACTERISTICS (TA = +25°C, VDD = 2.6 V, Vcont (H) = 2.6 V, Vcont (L) = 0 V, DC cut capacitors = 56 pF, using test fixture, unless otherw ise specified) INPUT-OUTPUT1 INSERTION LOSS vs. FREQUENCY 2.5 2.0 Insertion Loss Lins (dB) 1: 2: 3: 4: 5: INPUT-OUTPUT2 INSERTION LOSS vs. FREQUENCY 2.5 2.0 Insertion Loss Lins (dB) 1: 2: 3: 4: 5: –0.255 dB 0.5 GHz –0.305 dB 1.0 GHz –0.355 dB 2.0 GHz –0.408 dB 2.5 GHz –0.502 dB 3.0 GHz –0.255 dB 0.5 GHz –0.304 dB 1.0 GHz 1.5 1.0 0.5 0 –0.5 –1.0 –1.5 –2.0 –2.5 0.1 0.7 1.3 1.9 1 1.5 1.0 0.5 0 –0.5 –1.0 –1.5 –2.0 –0.354 dB 2.0 GHz –0.408 dB 2.5 GHz –0.506 dB 3.0 GHz 1 2 3 4 2 3 4 5 5 2.5 3.1 –2.5 0.1 0.7 1.3 1.9 2.5 3.1 Frequency f (GHz) Frequency f (GHz) INPUT-OUTPUT1 ISOLATION vs. FREQUENCY 50 40 30 Isolation ISL (dB) 1: 2: 3: 4: 5: INPUT-OUTPUT2 ISOLATION vs. FREQUENCY 50 40 30 Isolation ISL (dB) 1: 2: 3: 4: 5: –30.53 dB 0.5 GHz –24.659 dB 1.0 GHz –19.114 dB 2.0 GHz –17.362 dB 2.5 GHz –15.87 dB 3.0 GHz –30.378 dB 0.5 GHz –24.496 dB 1.0 GHz –18.545 dB 2.0 GHz 20 10 0 –10 –20 –30 –40 –50 0.1 1 2 3 20 10 0 –10 –20 –30 –40 1 2 3 –17.212 dB 2.5 GHz –15.717 dB 3.0 GHz 4 5 4 5 0.7 1.3 1.9 2.5 3.1 –50 0.1 0.7 1.3 1.9 2.5 3.1 Frequency f (GHz) Frequency f (GHz) INPUT-OUTPUT1 INPUT RETURN LOSS vs. FREQUENCY 50 40 Input Return Loss RLin (dB) 1: 2: 3: 4: 5: INPUT-OUTPUT2 INPUT RETURN LOSS vs. FREQUENCY 50 40 Input Return Loss RLin (dB) 1: 2: 3: 4: 5: –18.298 dB 0.5 GHz –22.409 dB 1.0 GHz –28.233 dB 2.0 GHz –31.992 dB 2.5 GHz –27.286 dB 3.0 GHz –18.557 dB 0.5 GHz –23.14 dB 1.0 GHz 30 20 10 0 –10 –20 –30 –40 –50 0.1 2 3 1 30 20 10 0 –10 –20 –30 –40 2 3 1 –29.248 dB 2.0 GHz –28.445 dB 2.5 GHz –23.756 dB 3.0 GHz 4 5 4 5 0.7 1.3 1.9 2.5 3.1 –50 0.1 0.7 1.3 1.9 2.5 3.1 Frequency f (GHz) Frequency f (GHz) Remark The graphs indicate nominal characteristics. 6 Data Sheet PG10635EJ01V0DS µPG2160T5K INPUT-OUTPUT1 OUTPUT RETURN LOSS vs. FREQUENCY 50 Output Return Loss RLout (dB) 1: 2: 3: 4: 5: INPUT-OUTPUT2 OUTPUT RETURN LOSS vs. FREQUENCY 50 Output Return Loss RLout (dB) 1: 2: 3: 4: 5: –18.38 dB 0.5 GHz –22.911 dB 1.0 GHz –28.715 dB 2.0 GHz –30.049 dB 2.5 GHz –25.211 dB 3.0 GHz –18.646 dB 0.5 GHz 40 30 20 10 0 –10 –20 –30 –40 –50 0.1 0.7 1.3 2 3 1.9 1 40 30 20 10 0 –10 –20 –30 –40 –50 0.1 0.7 1.3 2 3 1.9 1 –23.332 dB 1.0 GHz –31.078 dB 2.0 GHz –28.398 dB 2.5 GHz –23.042 dB 3.0 GHz 4 2.5 5 5 4 2.5 3.1 3.1 Frequency f (GHz) Frequency f (GHz) OUTPUT POWER vs. INPUT POWER +35 f = 2.0 GHz Output Power Pout (dBm) +30 +25 +20 +15 +10 +5 +8 +12 +16 +20 +24 +28 Input Power Pin (dBm) Remark The graphs indicate nominal characteristics. Data Sheet PG10635EJ01V0DS 7 µPG2160T5K MOUNTING PAD DIMENSIONS 6-PIN PLASTIC TSSON (UNIT: mm) 0.31 0.29 0.29 0.31 Remark The mounting pad layouts in this document are for reference only. 8 6–0.22 Data Sheet PG10635EJ01V0DS 0.35 0.35 µPG2160T5K PACKAGE DIMENSIONS 6-PIN PLASTIC TSSON (UNIT: mm) (Top View) 1.0±0.1 1.0±0.1 (Bottom View) 1.0±0.1 0.15+0.07 –0.05 0.15+0.07 –0.05 0.35±0.06 0.35±0.06 0.45 ±0.1 1.0±0.1 0.13±0.07 0.23±0.07 0.175±0.075 0.37+0.03 –0.05 Data Sheet PG10635EJ01V0DS 9 µPG2160T5K RECOMMENDED SOLDERING CONDITIONS This product should be soldered and mounted under the following recommended conditions. methods and conditions other than those recommended below, contact your nearby sales office. Soldering Method Infrared Reflow Soldering Conditions Peak temperature (package surface temperature) Time at peak temperature Time at temperature of 220°C or higher Preheating time at 120 to 180°C Maximum number of reflow processes Maximum chlorine content of rosin flux (% mass) Wave Soldering Peak temperature (molten solder temperature) Time at peak temperature Maximum number of flow processes Maximum chlorine content of rosin flux (% mass) Partial Heating Peak temperature (terminal temperature) Soldering time (per side of device) Maximum chlorine content of rosin flux (% mass) : 260°C or below : 10 seconds or less : 60 seconds or less : 120±30 seconds : 3 times : 0.2%(Wt.) or below : 260°C or below : 10 seconds or less : 1 time : 0.2%(Wt.) or below : 350°C or below : 3 seconds or less : 0.2%(Wt.) or below HS350 WS260 Condition Symbol IR260 For soldering Preheating temperature (package surface temperature) : 120°C or below Caution Do not use different soldering methods together (except for partial heating). 10 Data Sheet PG10635EJ01V0DS µPG2160T5K Bluetooth is a trademark owned by Bluetooth SIG, Inc., U.S.A. • T he information in this document is current a s of September, 2 006. T he information is subject to change without notice. For actual design-in, refer to the latest p ublications of NEC Electronics data s heets or data books, etc., for the most up-to-date specifications of NEC Electronics products. Not a ll products and/or types are available in every country. Please check with an NEC Electronics sales r epresentative for availability and additional information. • No part of this document may be copied or reproduced in any form or by any means without the prior w ritten c onsent of NEC Electronics. NEC Electronics assumes no responsibility for any errors that may a ppear in this document. • NEC E lectronics does not assume any liability for infringement of patents, copyrights or other intellectual property r ights of third parties by or arising from the use of NEC Electronics products listed in this document o r any other liability arising f rom the use of such products. No license, express, implied or otherwise, is granted under any patents, copyrights or other i ntellectual property rights of N EC E lectronics or o thers. • Descriptions of circuits, software and other related information in this document are provided for illustrative p urposes in semiconductor product operation and application examples. The incorporation of these c ircuits, software and information in the design of a customer's equipment shall be done under the full r esponsibility of the customer. N EC E lectronics a ssumes no responsibility for any losses incurred by c ustomers or third parties arising from t he use of these circuits, software and information. • While NEC E lectronics endeavors to enhance the quality, reliability and safety of NEC E lectronics products, customers agree and acknowledge that th e p ossibility of defects thereof cannot be eliminated entirely. To m inimize risks of damage to property or injury (including d eath) to persons a rising from defects in NEC E lectronics products, c ustomers must incorporate s ufficient safety m easures in their design, such as r edundancy, fire-containment and anti-failure features. • NEC Electronics p roducts are classified into the following t hree quality grades: "Standard", "Special" and "Specific". The "Specific" quality grade applies only to NEC E lectronics products developed based on a customerdesignated "quality assurance program" for a specific application. The recommended applications of an NEC E lectronics product depend on its quality grade, as indicated below. Customers must check the quality grade of each NEC E lectronics product b efore using it in a particular application. "Standard": Computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots. "Special": Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical equipment (not specifically d esigned for life support). "Specific": Aircraft, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems and medical equipment for life support, etc. The quality grade of NEC E lectronics products is "Standard" unless otherwise expressly specified in NEC E lectronics data sheets or data books, etc. I f c ustomers wish to use NEC Electronics products in applications n ot intended by NEC Electronics, they must contact an NEC Electronics sales representative in advance to d etermine NEC Electronics' willingness to support a given application. (Note) (1) "NEC E lectronics" as used in this statement means NEC E lectronics Corporation and also includes its majority-owned subsidiaries. (2) "NEC Electronics products" means any product developed or m anufactured by or for N EC Electronics ( as defined above). M8E 02. 11-1 Data Sheet PG10635EJ01V0DS 11 µPG2160T5K Caution GaAs Products This product uses gallium arsenide (GaAs). GaAs vapor and powder are hazardous to human health if inhaled or ingested, so please observe the following points. • Follow related laws and ordinances when disposing of the product. If there are no applicable laws and/or ordinances, dispose of the product as recommended below. 1. Commission a disposal company able to (with a license to) collect, transport and dispose of materials that contain arsenic and other such industrial waste materials. 2. Exclude the product from general industrial waste and household garbage, and ensure that the product is controlled (as industrial waste subject to special control) up until final disposal. • Do not burn, destroy, cut, crush, or chemically dissolve the product. • Do not lick the product or in any way allow it to enter the mouth. For further information, please contact NEC Compound Semiconductor Devices Hong Kong Limited E-mail: contact@ncsd-hk.necel.com Hong Kong Head Office TEL: +852-3107-7303 FAX: +852-3107-7309 Taipei Branch Office TEL: +886-2-8712-0478 FAX: +886-2-2545-3859 Korea Branch Office TEL: +82-2-558-2120 FAX: +82-2-558-5209 NEC Electronics (Europe) GmbH http://www.eu.necel.com/ TEL: +49-211-6503-0 FAX: +49-211-6503-1327 California Eastern Laboratories, Inc. http://www.cel.com/ TEL: +1-408-988-3500 FAX: +1-408-988-0279 Compound Semiconductor Devices Division NEC Electronics Corporation URL: http://www.ncsd.necel.com/ 0604 4590 Patrick Henry Drive Santa Clara, CA 95054-1817 Telephone: (408) 919-2500 Facsimile: (408) 988-0279 Subject: Compliance with EU Directives CEL certifies, to its knowledge, that semiconductor and laser products detailed below are compliant with the requirements of European Union (EU) Directive 2002/95/EC Restriction on Use of Hazardous Substances in electrical and electronic equipment (RoHS) and the requirements of EU Directive 2003/11/EC Restriction on Penta and Octa BDE. CEL Pb-free products have the same base part number with a suffix added. The suffix –A indicates that the device is Pb-free. The –AZ suffix is used to designate devices containing Pb which are exempted from the requirement of RoHS directive (*). In all cases the devices have Pb-free terminals. All devices with these suffixes meet the requirements of the RoHS directive. This status is based on CEL’s understanding of the EU Directives and knowledge of the materials that go into its products as of the date of disclosure of this information. Restricted Substance per RoHS Lead (Pb) Mercury Cadmium Hexavalent Chromium PBB PBDE Concentration Limit per RoHS (values are not yet fixed) < 1000 PPM < 1000 PPM < 100 PPM < 1000 PPM < 1000 PPM < 1000 PPM Concentration contained in CEL devices -A Not Detected Not Detected Not Detected Not Detected Not Detected Not Detected -AZ (*) If you should have any additional questions regarding our devices and compliance to environmental standards, please do not hesitate to contact your local representative. Important Information and Disclaimer: Information provided by CEL on its website or in other communications concerting the substance content of its products represents knowledge and belief as of the date that it is provided. CEL bases its knowledge and belief on information provided by third parties and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. CEL has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. CEL and CEL suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall CEL’s liability arising out of such information exceed the total purchase price of the CEL part(s) at issue sold by CEL to customer on an annual basis. See CEL Terms and Conditions for additional clarification of warranties and liability.