SF15PT

CHENMKO ENTERPRISE CO.,LTD GLASS PASSIVATED SUPER FAST RECTIFIER VOLTAGE RANGE 50 - 1000 Volts CURRENT 1.0 Ampere FEATURES * Plastic package has Underwriters Laboratory Flammability Classification 94V-0 * High reliability * Low leakage * Low forward voltage * High current capability * Super fast switching speed * High surge capability * Good for switching mode circuit S F11PT THRU SF18PT DO-41 0.034(0.9) DIA. 0.028(0.7) MECHANICAL DATA Case: JEDEC DO-41 molded plastic Terminals: Plated axial leads, solderable per MIL-STD-750, Method 2026 Polarity: Color band denotes cathode end Mounting Position: Any Weight: 0.33 gram 1.0(25.4) MIN. 0.205(5.2) 0.166(4.2) 0.107(2.7) DIA. 0.080(2.0) 1.0(25.4) MIN. MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25oC ambient temperature unless otherwise specified. Single phase, half wave, 60 HZ, resistive or inductive load. For capacitive load, derate current by 20%. Dimensions in inches and (millimeters) DO-41 UNITS Volts Volts Volts Amps MAXIMUM RATINGES ( At TA = 25oC unless otherwise noted ) RATINGS Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Current at TA = 55oC Peak Forward Surge Current 8.3 ms single half sine-wave IFSM superimposed on rated load (JEDEC method) Typical Junction Capacitance (Note 1) Operating and Storage Temperature Range CJ TJ, TSTG 15 -65 to +150 10 pF o SYMBOL VRRM VRMS VDC IO SF11PT SF12PT SF13PT SF14PT SF15PT SF16PT SF17PT SF18PT 50 35 50 100 70 100 200 140 200 300 210 300 1.0 400 280 400 600 420 600 800 560 800 1000 700 1000 30 Amps C ELECTRICAL CHARACTERISTICS ( At TA = 25oC unless otherwise noted ) CHARACTERISTICS Maximum Instantaneous Forward Voltage at 1.0 A DC Maximum DC Reverse Current at Rated DC Blocking Voltage Maximum Reverse Recovery Time (Note 2) NOTES : 1. Measured at 1.0 MHZ and applied reverse voltage of 4.0 volts 2. Test Conditions : IF = 0.5 A, IR = -1.0 A, IRR = -0.25 A T A = 2 5 oC TA = 125oC IR 50 trr 35 45 uAmps nSec 2001-6 SYMBOL VF SF11PT SF12PT SF13PT SF14PT SF15PT SF16PT SF17PT SF18PT UNITS Volts uAmps 0.95 5.0 1.27 1.75 RATING CHARACTERISTIC CURVES ( SF11PT THRU SF18PT ) FIG. 1 - TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC 50 NONINDUCTIVE 10 NONINDUCTIVE trr +0.5A (-) 0 PULSE GENERATOR (NOTE 2) 1 NONINDUCTIVE OSCILLOSCOPE (NOTE 1) (+) -1.0A NOTES: 1. Rise Time = 7 ns max. Input Impedance = 1 megohm. 22 pF. 2. Rise Time = 10 ns max. Source Impedlance= 50 ohms. 1cm SET TIME BASE FOR 10 nS/cm -0.25A AVERAGE FORWARD CURRENT, ( A ) FIG. 2 - TYPICAL FORWARD CURRENT DERATING CURVE 1.0 (+) 25 Vdc (approx) (-) D.U.T 0.5 Single Phase Half Wave 60Hz Resistive or Inductive Load 0 0 25 50 75 100 125 150 175 AMBIENT TEMPERATURE ( OC ) FIG. 3 - TYPICAL REVERSE CHARACTERISTICS 100 INSTANTANEOUS FORWARD CURRENT, ( A ) INSTANTANEOUS REVERSE CURRENT, (uA) 10 FIG. 4 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS PT 11P TJ =100oC 1.0 0.1 SF 10 1.0 .1 TJ =25 C o TJ =25oC .01 .01 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE, ( % ) .001 0 .2 .4 .6 .8 1.0 1.2 1.4 1.6 INSTANTANEOUS FORWARD VOLTAGE, ( V ) 1.8 FIG. 5 - MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT PEAK FORWARD SURGE CURRENT, ( A ) 35 JUNCTION CAPACITANCE, ( pF ) 30 25 20 15 10 5 0 1 2 5 10 20 NUMBER OF CYCLES AT 60 Hz 50 100 8.3ms Single Half Sine-Wave (JEDEC Method) FIG. 6 - TYPICAL JUNCTION CAPACITANCE 200 100 60 40 20 10 6 4 2 1 .1 .2 .4 1.0 2 4 10 20 REVERSE VOLTAGE, ( V ) 40 100 TJ =25oC SF11 PT~S F15P T SF16P T~SF1 8PT SF 15 TJ =125oC Pulse Width = 300uS 1% Duty Cycle ~ PT 16 SF SF T~S PT 18 PT F14