UPL22CTPT

CHENMKO ENTERPRISE CO.,LTD SURFACE MOUNT GLASS PASSIVATED H IGH EFFICIENCY SILICON RECTIFIER VOLTAGE RANGE 50 - 1000 Volts CURRENT 2.0 Ampere FEATURE *Sm al l S u r f ac e M o u n t i n g T y p e. (SMP) * Low forward voltage, high current capability * Low leakage current * Glass passivated junction * High temperature soldering guaranteed : 260oC/10 seconds at terminals 0.081 (2.05) 0.077 (1.95) (3) UPL21CTPT THRU UPL28CTPT P ROVISIONAL SPEC. SMP 0.170 (4.31) 0.163 (4.15) (1) 0.077 (1.95) 0.073 (1.85) 0.005 (0.15 Min.) (2) 0.019 (0.50 Min.) 0.045 (1.16) 0.042 (1.07) 0.019 (0.50 Min.) 0.264 (6.70) 0.254 (6.46) 0.212 (5.38) 0.208 (5.29) CIRCUIT (2) (1) 0.055 (1.40) 0.051 (1.30) (3) Dimensions in inches and (millimeters) SMP UNITS Volts Volts Volts Amps MAXIMUM RATINGES ( At TA = 25oC unless otherwise noted ) RATINGS Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current TL = 110 C Peak Forward Surge Current 8.3 ms single half sine-wave IFSM superimposed on rated load (JEDEC method) Typical Junction Capacitance (Note 1) Operating and Storage Temperature Range CJ TJ, TSTG 15 -65 to +150 12 pF o o SYMBOL VRRM VRMS VDC IO UPL21CTPT UPL22CTPT UPL23CTPT UPL24CTPT UPL25CTPT UPL26CTPT UPL27CTPT UPL28CTPT 50 35 50 100 70 100 200 140 200 300 210 300 2.0 400 280 400 600 420 600 800 560 800 1000 700 1000 30 Amps C ELECTRICAL CHARACTERISTICS ( At TA = 25oC unless otherwise noted ) CHARACTERISTICS Maximum Instantaneous Forward Voltage at 1.0 A DC Maximum DC Reverse Current at Rated DC Blocking Voltage at TA = 25oC Maximum Full Load Reverse Current Average, Full Cycle at TA = 55oC Maximum Reverse Recovery Time (Note 2) NOTES : 1. Measured at 1.0 MHZ and applied reverse voltage of 4.0 volts 2. Test Conditions : IF = 0.5 A, IR = -1.0 A, IRR = -0.25 A SYMBOL VF UPL21CTPT UPL22CTPT UPL23CTPT UPL24CTPT UPL25CTPT UPL26CTPT UPL27CTPT UPL28CTPT UNITS Volts uAmps uAmps 0.95 5.0 1.27 1.75 IR 100 trr 35 45 nSec 2004-7 RATING CHARACTERISTIC CURVES ( UPL21CTPT THRU UPL28CTPT ) FIG. 1 - TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC 50 NONINDUCTIVE 10 NONINDUCTIVE trr +0.5A (-) 0 PULSE GENERATOR (NOTE 2) 1 NONINDUCTIVE OSCILLOSCOPE (NOTE 1) (+) -1.0A NOTES: 1. Rise Time = 7 ns max. Input Impedance = 1 megohm. 22 pF. 2. Rise Time = 10 ns max. Source Impedlance= 50 ohms. 1cm SET TIME BASE FOR 10/20 nS/cm -0.25A AVERAGE FORWARD CURRENT, ( A ) FIG. 2 - TYPICAL FORWARD CURRENT DERATING CURVE 3.0 (+) 25 Vdc (approx) (-) D.U.T 2.0 Single Phase Half Wave 60Hz Resistive or Inductive Load 1.0 0 0 25 50 75 100 125 150 175 LEAD TEMPERATURE ( OC ) FIG. 3 - TYPICAL REVERSE CHARACTERISTICS 100 INSTANTANEOUS FORWARD CURRENT, ( A ) INSTANTANEOUS REVERSE CURRENT, (uA) 10 FIG. 4 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS TP T 3C TP T PL2 6C L21 CT UP L24 TJ =100oC 1.0 TJ =25oC 0.1 .1 .01 .01 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE, ( % ) .001 0 .2 .4 .6 .8 1.0 1.2 1.4 1.6 INSTANTANEOUS FORWARD VOLTAGE, ( V ) 1.8 FIG. 5 - MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT PEAK FORWARD SURGE CURRENT, ( A ) 35 JUNCTION CAPACITANCE, ( pF ) 30 25 20 15 10 5 0 1 2 5 10 20 NUMBER OF CYCLES AT 60 Hz 50 100 8.3ms Single Half Sine-Wave (JEDEC Method) FIG. 6 - TYPICAL JUNCTION CAPACITANCE 200 100 60 40 20 10 6 4 2 1 .1 .2 .4 1.0 2 4 10 20 REVERSE VOLTAGE, ( V ) 40 100 TJ =25oC UPL26C UPL2 1CTP T~UP L25C TPT TPT~U PL28C TPT UP TJ =25oC UP L2 7C 10 PT UP TP TJ =125oC PT ~U L2 1.0 CT T~ UP Pulse Width = 300uS 1% Duty Cycle PL2 5C ~U TP L2 8C T TP T