UPL43CTPT

CHENMKO ENTERPRISE CO.,LTD SURFACE MOUNT GLASS PASSIVATED S UPER FAST SILICON RECTIFIER VOLTAGE RANGE 50 - 1000 Volts CURRENT 4.0 Amperes FEATURE *Sm al l S u r f ac e M o u n t i n g T y p e. (SMP) * Low forward voltage, high current capability * Low leakage current * Glass passivated junction * High temperature soldering guaranteed : 260oC/10 seconds at terminals 0.081 (2.05) 0.077 (1.95) (3) U PL41CT PT THRU UPL48CT PT P ROVISIONAL SPEC. SMP 0.170 (4.31) 0.163 (4.15) (1) 0.077 (1.95) 0.073 (1.85) 0.005 (0.15 Min.) (2) 0.019 (0.50 Min.) 0.045 (1.16) 0.042 (1.07) 0.019 (0.50 Min.) 0.264 (6.70) 0.254 (6.46) 0.212 (5.38) 0.208 (5.29) CIRCUIT (2) (1) 0.055 (1.40) 0.051 (1.30) (3) Dimensions in inches and (millimeters) SMP UNITS Volts Volts Volts Amps MAXIMUM RATINGES ( At TA = 25oC unless otherwise noted ) RATINGS Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Current TL = 100 C Peak Forward Surge Current 8.3 ms single half sine-wave IFSM superimposed on rated load (JEDEC method) Typical Junction Capacitance (Note 1) Operating and Storage Temperature Range CJ TJ, TSTG 30 -65 to +150 20 pF o o SYMBOL VRRM VRMS VDC IO UPL41CTPT UPL42CTPT UPL43CTPT UPL44CTPT UPL45CTPT UPL46CTPT UPL47CTPT UPL48CTPT 50 35 50 100 70 100 200 140 200 300 210 300 4.0 400 280 400 600 420 600 800 560 800 1000 700 1000 50 Amps C ELECTRICAL CHARACTERISTICS ( At TA = 25oC unless otherwise noted ) CHARACTERISTICS Maximum Instantaneous Forward Voltage at 2.0 A DC Maximum DC Reverse Current at Rated DC Blocking Voltage Maximum Reverse Recovery Time (Note 2) NOTES : 1. Measured at 1.0 MHZ and applied reverse voltage of 4.0 volts 2. Test Conditions : IF = 0.5 A, IR = -1.0 A, IRR = -0.25 A @ T A = 2 5 oC @ TA = 100oC IR 100 trr 35 45 uAmps nSec 2004-7 SYMBOL VF UPL41CTPT UPL42CTPT UPL43CTPT UPL44CTPT UPL45CTPT UPL46CTPT UPL47CTPT UPL48CTPT UNITS Volts uAmps 0.95 5.0 1.27 1.75 RATING CHARACTERISTIC CURVES ( UPL41CTPT THRU UPL48CTPT ) 50 NONINDUCTIVE 10 NONINDUCTIVE trr +0.5A (-) 0 PULSE GENERATOR (NOTE 2) -0.25A AVERAGE FORWARD CURRENT, ( A ) FIG. 1 - TEST CIRCUIT DIAGRAM AND REVERSE RECOVERY TIME CHARACTERISTIC FIG. 2 - TYPICAL FORWARD CURRENT DERATING CURVE 4.0 (+) 25 Vdc (approx) (-) D.U.T 2.0 Single Phase Half Wave 60Hz Resistive or Inductive Load 1 NONINDUCTIVE OSCILLOSCOPE (NOTE 1) (+) -1.0A NOTES: 1. Rise Time = 7 ns max. Input Impedance = 1 megohm. 22 pF. 2. Rise Time = 10 ns max. Source Impedlance= 50 ohms. 1cm SET TIME BASE FOR 10 nS/cm 0 0 25 50 75 100 125 150 175 LEAD TEMPERATURE ( OC ) FIG. 3 - TYPICAL REVERSE CHARACTERISTICS 100 INSTANTANEOUS FORWARD CURRENT, ( A ) INSTANTANEOUS REVERSE CURRENT, (uA) 10 FIG. 4 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 4C TP T T TP 1C L4 UP TJ =75oC 1.0 0.1 .1 TJ =25 C o TJ =25oC .01 .01 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE, ( % ) .001 0 .2 .4 .6 .8 1.0 1.2 1.4 1.6 INSTANTANEOUS FORWARD VOLTAGE, ( V ) 1.8 FIG. 5 - MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT PEAK FORWARD SURGE CURRENT, ( A ) 70 JUNCTION CAPACITANCE, ( pF ) 60 50 40 30 20 10 0 1 2 5 10 20 NUMBER OF CYCLES AT 60 Hz 50 100 8.3ms Single Half Sine-Wave (JEDEC Method) FIG. 6 - TYPICAL JUNCTION CAPACITANCE 200 100 60 40 20 10 6 4 2 1 .1 .2 .4 1.0 2 4 10 20 REVERSE VOLTAGE, ( V ) 40 100 TJ =25oC UPL4 UPL4 1CTP T~UP L45C 6CTP T~UP L48C TPT UP TPT L4 6C TP 10 1.0 TP UP T~ TJ =100oC T~ UP Pulse Width = 300uS 1% Duty Cycle L4 UP 5C L4 L4 8C TP T