CS5378-ISZ

CS5378 Low-power Single-channel Decimation Filter Features Single-channel Digital Decimation Filter Multiple On-chip FIR and IIR Coefficient Sets Programmable Coefficients for Custom Filters Synchronous Operation Description The CS5378 is a multi-function digital filter utilizing a lowpower signal processing architecture to achieve efficient filtering for a delta-sigma-type modulator. By combining the CS5378 with a CS3301A/02A differential amplifier and a CS5373A modulator + test DAC, a synchronous high-resolution, self-testing, single-channel measurement system can be designed quickly and easily. Digital filter coefficients for the CS5378 FIR and IIR filters are included on-chip for a simple setup, or they can be programmed for custom applications. Selectable digital filter decimation ratios produce output word rates from 4000 SPS to 1 SPS, resulting in measurement bandwidths ranging from 1600 Hz down to 400 mHz when using the on-chip coefficient sets. The CS5378 includes integrated peripherals to simplify system design: a low-jitter PLL for standard clock or Manchester inputs, offset and gain corrections, a test DAC bit stream generator, a time break controller, and eight general-purpose I/O pins. Integrated PLL for Clock Generation 1.024 MHz, 2.048 MHz, or 4.096 MHz Input Standard Clock or Manchester Input Selectable Output Word Rate 4000, 2000, 1000, 500, 333, 250 SPS 200, 125, 100, 50, 40, 25, 20, 10, 5, 1 SPS Digital Gain and Offset Corrections Test DAC Bit-stream Generator Digital Sine Wave Output Time Break Controller, General-purpose I/O Microcontroller or EEPROM Configuration Small-footprint, 28-pin SSOP Package Low Power Consumption 16 mW at 500 SPS OWR Flexible Power Supplies I/O Interface and PLL: 3.3 V or 5.0 V Digital Logic Core: 2.5 V, 3.3 V or 5.0 V I ORDERING INFORMATION See page 86. VDDCORE SS:EECS VDDPAD VDDPLL DRDY MISO MOSI SCK PLL, Clock Generation Serial Interface Reset, Synchronization CLK MCLK RESET SYNC MSYNC TIMEB Time Break Controller Decimation and Filtering Engine Test Bit Stream Controller TBSDATA GPIO7:BOOT GPIO6:PLL2 GPIO5:PLL1 GPIO4:PLL0 GPIO3 GPIO2 GPIO1 GPIO0 Modulator Data Interface GPIO General Purpose I/O MDATA MFLAG GNDPAD http://www.cirrus.com Copyright © Cirrus Logic, Inc. 2008 (All Rights Reserved) GNDCORE GNDPLL SEP ‘08 DS639F2 CS5378 TABLE OF CONTENTS 1. General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 1.1. 1.2. 1.3. 1.4. Digital Filter Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Integrated Peripheral Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 System Level Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 Configuration Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 2. Characteristics and Specifications . . . . . . . . . . . . . . . . . . . . . . . . . 12 Specified Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 Thermal Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 Digital Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 Power Consumption. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13 Switching Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 3. System Design with CS5378. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 3.1. 3.2. 3.3. 3.4. 3.5. 3.6. 3.7. 3.8. Power Supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 Reset Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 PLL and Clock Generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 Synchronization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 System Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 Digital Filter Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 Data Collection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 Integrated peripherals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 4. Power Supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 4.1. Pin Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 4.2. Bypass Capacitors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 4.3. Power Consumption. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 5. Reset Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 5.1. Pin Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 5.2. Reset Self-Tests. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 5.3. Boot Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21 6. PLL and Clock Generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 6.1. 6.2. 6.3. 6.4. 7.1. 7.2. 7.3. 7.4. 7.5. 8.1. 8.2. 8.3. 8.4. 8.5. Pin Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 PLL Mode Select . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 Synchronous Clocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 Master Clock Jitter and Skew. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 Pin Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 MSYNC Generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 Digital Filter Synchronization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 Modulator Synchronization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 Test Bit Stream Synchronization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 Pin Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 EEPROM Hardware Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 EEPROM Organization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 EEPROM Configuration Commands . . . . . . . . . . . . . . . . . . . . . . . . . . .27 Example EEPROM Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29 7. Synchronization. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 8. Configuration By EEPROM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 9. Configuration By Microcontroller . . . . . . . . . . . . . . . . . . . . . . . . . . 30 DS639F2 2 CS5378 9.1. 9.2. 9.3. 9.4. 9.5. 10.1. 10.2. 10.3. 10.4. 10.5. Pin Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 Microcontroller Hardware Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 Microcontroller Serial Transactions . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 Microcontroller Configuration Commands . . . . . . . . . . . . . . . . . . . . . . .33 Example Microcontroller Configuration . . . . . . . . . . . . . . . . . . . . . . . . .35 Pin Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36 Modulator Clock Generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36 Modulator Synchronization. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36 Modulator Data Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 Modulator Flag Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 10. Modulator Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 11. Digital Filter Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 11.1. Filter Coefficient Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38 11.2. Filter Configuration Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38 12. SINC Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 12.1. 12.2. 12.3. 12.4. 13.1. 13.2. 13.3. 13.4. 13.5. 14.1. 14.2. 14.3. 14.4. 14.5. 14.6. 14.7. SINC1 Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40 SINC2 Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40 SINC3 Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40 SINC Filter Synchronization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40 FIR1 Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44 FIR2 Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44 On-Chip FIR Coefficients . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44 Programmable FIR Coefficients . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45 FIR Filter Synchronization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45 IIR Architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52 IIR1 Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52 IIR2 Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52 IIR3 Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53 On-Chip IIR Coefficients . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53 Programmable IIR Coefficients . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53 IIR Filter Synchronization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53 13. FIR Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 14. IIR Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 15. Gain and Offset Correction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 15.1. Gain Correction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56 15.2. Offset Correction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56 15.3. Offset Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57 16. Serial Data Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 16.1. Pin Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58 16.2. Serial Data Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58 16.3. Serial Data Transactions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59 17. Test Bit Stream Generator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 17.1. 17.2. 17.3. 17.4. 17.5. 17.6. Pin Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60 TBS Architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60 TBS Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60 TBS Data Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61 TBS Sine Wave Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61 TBS Loopback Testing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62 DS639F2 3 CS5378 17.7. TBS Synchronization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62 18. Time Break Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 18.1. Pin Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63 18.2. Time Break Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63 18.3. Time Break Delay. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63 19. General Purpose I/O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64 19.1. 19.2. 19.3. 19.4. 19.5. Pin Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64 GPIO Architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64 GPIO Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64 GPIO Input Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64 GPIO Output Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64 20. Register Summary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 20.1. SPI Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66 20.2. Digital Filter Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71 21. 22. 23. 24. 25. Pin Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83 Package Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85 Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86 Environmental, Manufacturing, & Handling Information . . . . . . . 86 Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87 LIST OF FIGURES Figure 1. CS5378 Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Figure 2. Digital Filtering Stages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Figure 3. FIR and IIR Coefficient Set Selection Word . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Figure 4. MOSI Write Timing in SPI Slave Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Figure 5. MISO Read Timing in SPI Slave Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Figure 6. Serial Data Read Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Figure 7. SYNC, MCLK, MSYNC, MDATA Interface Timing. . . . . . . . . . . . . . . . . . . . . 16 Figure 8. TBS Output Data Timing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Figure 9. Single-Channel System Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Figure 10. Power Supply Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Figure 11. Reset Control Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Figure 12. Clock Generation Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Figure 13. Synchronization Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Figure 14. EEPROM Configuration Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Figure 15. EEPROM Serial Read Transactions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Figure 16. 8 Kbyte EEPROM Memory Organization . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Figure 17. Serial Interface Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Figure 18. Microcontroller Serial Transactions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Figure 19. SPI Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Figure 20. Modulator Data Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Figure 21. Digital Filter Stages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Figure 22. FIR and IIR Coefficient Set Selection Word . . . . . . . . . . . . . . . . . . . . . . . . . 39 Figure 23. SINC Filter Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Figure 24. SINC Filter Stages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Figure 25. FIR Filter Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Figure 26. FIR Filter Stages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Figure 27. FIR1 Coefficients . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Figure 28. FIR2 Linear Phase Coefficients . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 DS639F2 4 CS5378 Figure 29. Figure 30. Figure 31. Figure 32. Figure 33. Figure 34. Figure 35. Figure 36. Figure 37. Figure 38. Figure 39. Figure 40. Figure 41. Figure 42. Figure 43. Figure 44. Figure 45. Figure 46. Figure 47. Figure 48. Figure 49. Figure 50. Figure 51. Figure 52. Figure 53. Figure 54. FIR2 Minimum Phase Coefficients . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IIR Filter Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . IIR Filter Stages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Gain and Offset Correction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Serial Data Interface Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32-bit Serial Data Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SD Port Transaction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Test Bit Stream Generator Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . Time Break Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . GPIO Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SPI Control Register SPICTRL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SPI Command Register SPICMD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SPI Data Register SPIDAT1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SPI Data Register SPIDAT2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hardware Configuration Register CONFIG. . . . . . . . . . . . . . . . . . . . . . . . . . GPIO Configuration Register GPCFG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Filter Configuration Register FILTCFG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Gain Correction Register GAIN. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Offset Correction Register OFFSET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Time Break Counter Register TIMEBRK . . . . . . . . . . . . . . . . . . . . . . . . . . . Test Bit Stream Configuration Register TBSCFG. . . . . . . . . . . . . . . . . . . . . Test Bit Stream Gain Register TBSGAIN . . . . . . . . . . . . . . . . . . . . . . . . . . . User Defined System Register SYSTEM1 . . . . . . . . . . . . . . . . . . . . . . . . . . Hardware Version ID Register VERSION . . . . . . . . . . . . . . . . . . . . . . . . . . . Self Test Result Register SELFTEST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CS5378 Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 52 54 56 58 58 59 60 63 64 67 68 69 70 72 73 74 75 76 77 78 79 80 81 82 83 LIST OF TABLES Table 1. Microcontroller and EEPROM Configuration Commands . . . . . . . . . . . . . . . . . 9 Table 2. TBS Configurations Using On-Chip Data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Table 3. SPI and Digital Filter Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Table 4. PLL and BOOT Mode Reset Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Table 5. PLL Mode Selections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Table 6. Maximum EEPROM Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Table 7. EEPROM Boot Configuration Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Table 8. Example EEPROM File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Table 9. Microcontroller Boot Configuration Commands . . . . . . . . . . . . . . . . . . . . . . . . 33 Table 10. Example Microcontroller Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 Table 11. SINC Filter Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Table 12. SINC1 and SINC2 Filter Coefficients . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 Table 13. SINC3 Filter Coefficients . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Table 14. FIR Filter Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Table 15. SINC + FIR Group Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Table 16. Minimum Phase Group Delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Table 16. IIR Filter Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 Table 17. IIR Filter Coefficients . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 Table 18. TBS Configurations Using On-chip Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 DS639F2 5 CS5378 VDDCORE SS:EECS VDDPAD VDDPLL DRDY MISO MOSI SCK PLL, Clock Generation Serial Interface Reset, Synchronization CLK MCLK RESET SYNC MSYNC TIMEB Time Break Controller Decimation and Filtering Engine Test Bit Stream Controller TBSDATA GPIO7:BOOT GPIO6:PLL2 GPIO5:PLL1 GPIO4:PLL0 GPIO3 GPIO2 GPIO1 GPIO0 Modulator Data Interface GPIO General Purpose I/O MDATA MFLAG GNDPAD Figure 1. CS5378 Block Diagram 1. GENERAL DESCRIPTION The CS5378 is a single channel digital filter with integrated system peripherals. Figure 1 illustrates a simplified block diagram of the CS5378. 40, 25, 20, 10, 5, 1 SPS. • Flexible digital filter configuration. (See Figure 2) • • Cascaded SINC, FIR, and IIR filters with selectable output stage. Linear and minimum phase FIR low-pass filter coefficients included. 3 Hz Butterworth IIR high-pass filter coefficients included. FIR and IIR coefficients programmable to create a custom filter response. 1.1 Digital Filter Features • • Single channel decimation filter for CS5373A ∆Σ modulator. Synchronous operation for simultaneous sampling in multi-sensor systems. • Internal synchronization of digital filter phase to an external SYNC signal. Output word rates, including low bandwidth rates. Standard output rates: 4000, 2000, 1000, 500, 333, 250 SPS. Low bandwidth rates: 200, 125, 100, 50, Digital gain correction to normalize sensor gain. Digital offset correction and calibration. Offset correction to remove measurement DS639F2 GNDCORE GNDPLL 6 CS5378 Modulator Input 512 kHz Sinc Filter 2 - 64000 FIR1 4 FIR2 2 IIR1 1 Order st IIR2 2 nd Order Gain & DC Offset Corrections Output to High Speed Serial Interface Output Word Rate from 4000 SPS ~ 1 SPS Figure 2. Digital Filtering Stages DC offset. Calibration engine for automatic calculation of offset correction factor. • Time break controller to record system timing information. Dedicated TB status bit in the output data stream. Programmable output delay to match system group delay. 1.2 Integrated Peripheral Features • Low jitter PLL to generate local clocks. • 1.024 MHz, 2.048 MHz, 4.096 MHz standard clock or Manchester encoded input. • 8 General Purpose I/O (GPIO) pins for local hardware control. Synchronous operation for simultaneous sampling in multi-sensor systems. MCLK / MSYNC output signals to synchronize external components. Asynchronous operation to 4 MHz for direct connection to system telemetry. Internal 8-deep data FIFO for flexible output timing. Selectable 24-bit data only or 32-bit status+data output. 1.3 System Level Features • Flexible configuration options. • Configuration 'on-the-fly' via microcontroller or system telemetry. Fixed configuration via stand-alone boot EEPROM. 16 mW at 500 SPS OWR. 100 µW standby mode. Separate digital logic core, telemetry I/O, and PLL power supplies. Telemetry I/O and PLL interfaces operate • High speed serial data output. - Low power consumption. - • Flexible power supply configurations. - • Digital test bit stream signal generator suitable for CS5373A ∆Σ test DAC. Sine wave output mode for testing total harmonic distortion. DS639F2 7 CS5378 from 3.3 V or 5 V. • Digital logic core operates from 2.5 V, 3.3 V or 5 V. Total footprint 8 mm x 10 mm plus three bypass capacitors. • EEPROM boot sets a fixed operational configuration. Small 28-pin SSOP package. - Configuration commands written through the serial interface. (See Table 1) Standardized microcontroller interface using SPI™ registers. (See Table 3) Commands write digital filter registers and FIR / IIR filter coefficients. Digital filter registers set hardware configuration options. 1.4 Configuration Interface • Configuration from microcontroller or standalone boot EEPROM. Microcontroller boot permits reconfiguration during operation. - DS639F2 8 CS5378 Microcontroller Boot Configuration Commands Name NOP WRITE DF REGISTER READ DF REGISTER WRITE FIR COEFFICIENTS WRITE IIR COEFFICIENTS CMD 24-bit 000000 000001 000002 000003 000004 DAT1 24-bit REG REG [DATA] NUM FIR1 (FIR COEF) a11 b11 a22 b21 COEF SEL DAT2 24-bit DATA NUM FIR2 (FIR COEF) b10 a21 b20 b22 Description No Operation Write Digital Filter Register Read Digital Filter Register Write Custom FIR Coefficients Write Custom IIR Coefficients WRITE ROM COEFFICIENTS NOP NOP FILTER START FILTER STOP 000005 000006 000007 000008 000009 Use On-Chip Coefficients No Operation No Operation Start Digital Filter Operation Stop Digital Filter Operation EEPROM Boot Configuration Commands Name NOP WRITE DF REGISTER WRITE FIR COEFFICIENTS CMD 8-bit 00 01 02 DATA 24-bit REG DATA NUM FIR1 NUM FIR2 (FIR COEF) a11 b10 b11 a21 a22 b20 b21 b22 COEF SEL No Operation Write Digital Filter Register Write Custom FIR Coefficients Description WRITE IIR COEFFICIENTS 03 Write Custom IIR Coefficients WRITE ROM COEFFICIENTS NOP NOP FILTER START 04 05 06 07 Use On-Chip Coefficients No Operation No Operation Start Digital Filter Operation [DATA] indicates data word returned from digital filter. (DATA) indicates multiple words of this type are to be written. Table 1. Microcontroller and EEPROM Configuration Commands DS639F2 9 CS5378 Bits Selection 23:20 0000 19:16 0000 15:12 IIR2 11:8 IIR1 7:4 FIR2 3:0 FIR1 Bits 15:12 0000 0001 0010 0011 0100 IIR2 Coefficients 3 Hz @ 2000 SPS 3 Hz @ 1000 SPS 3 Hz @ 500 SPS 3 Hz @ 333 SPS 3 Hz @ 250 SPS Bits 11:8 0000 0001 0010 0011 0100 IIR1 Coefficients 3 Hz @ 2000 SPS 3 Hz @ 1000 SPS 3 Hz @ 500 SPS 3 Hz @ 333 SPS 3 Hz @ 250 SPS Bits 3:0 0000 0001 FIR1 Coefficients Linear Phase Minimum Phase Bits 7:4 0000 0001 FIR2 Coefficients Linear Phase Minimum Phase Figure 3. FIR and IIR Coefficient Set Selection Word Test Bit Stream Characteristic Equation: (Signal Freq) * (# TBS Data) * (Interpolation + 1) = Output Rate Example: (31.25 Hz) * (1024) * (0x07 + 1) = 256 kHz Signal Frequency (TBSDATA) 10.00 Hz 10.00 Hz 25.00 Hz 25.00 Hz 31.25 Hz 31.25 Hz 50.00 Hz 50.00 Hz 125.00 Hz 125.00 Hz Output Rate (TBSCLK) 256 kHz 512 kHz 256 kHz 512 kHz 256 kHz 512 kHz 256 kHz 512 kHz 256 kHz 512 kHz Output Rate Selection (RATE) 0x4 0x5 0x4 0x5 0x4 0x5 0x4 0x5 0x4 0x5 Interpolation Selection (INTP) 0x18 0x31 0x09 0x13 0x07 0x0F 0x04 0x09 0x01 0x03 Table 2. TBS Configurations Using On-Chip Data DS639F2 10 CS5378 SPI Registers Name SPICTRL SPICMD SPIDAT1 SPIDAT2 Addr. 00 - 02 03 - 05 06 - 08 09 - 0B Type R/W R/W R/W R/W # Bits 8, 8, 8 8, 8, 8 8, 8, 8 8, 8, 8 SPI Control SPI Command SPI Data 1 SPI Data 2 Description Digital Filter Registers Name CONFIG RESERVED GPCFG RESERVED FILTCFG GAIN RESERVED OFFSET RESERVED TIMEBRK TBSCFG TBSGAIN SYSTEM1 SYSTEM2 VERSION SELFTEST Addr. 00 01-0D 0E 0F-1F 20 21 22-24 25 26-28 29 2A 2B 2C 2D 2E 2F Type R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W # Bits 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 Description Hardware Configuration Reserved GPIO[7:0] Direction, Pull-up Enable, and Data Reserved Digital Filter Configuration Gain Correction Reserved Offset Correction Reserved Time Break Delay Test Bit Stream Configuration Test Bit Stream Gain User Defined System Register 1 User Defined System Register 2 Hardware Version ID Self-Test Result Code Table 3. SPI and Digital Filter Registers PLL[2:0] 111 110 101 100 011 010 001 000 Mode Selection on Reset 32.768 MHz clock input (PLL bypass). 1.024 MHz clock input. 2.048 MHz clock input. 4.096 MHz clock input. 32.768 MHz clock input (PLL bypass). 1.024 MHz Manchester input. 2.048 MHz Manchester input. 4.096 MHz Manchester input. BOOT 1 0 Mode Selection on Reset EEPROM boot Microcontroller boot Configuration Note: States of the PLL[2:0] and BOOT pins are latched immediately after reset to select modes. These pins have a weak (~100 kΩ) pull-up resistor enabled by default. An external 10 kΩ pull-down is required to set a low condition. Table 4. PLL and BOOT Mode Reset Configurations DS639F2 11 CS5378 2. CHARACTERISTICS AND SPECIFICATIONS • • • Min / Max characteristics and specifications are guaranteed over the Specified Operating Conditions. Typical performance characteristics and specifications are derived from measurements taken at nominal supply voltages and TA = 25°C. GND, GND1, GND2 = 0 V, all voltages with respect to 0 V. SPECIFIED OPERATING CONDITIONS Parameter Logic Core Power Supply PLL Power Supply I/O Power Supply Ambient Operating Temperature Industrial (-IQ) Symbol VDDCORE VDDPLL VDDPAD TA Min 2.375 3.135 3.135 -40 Nom 2.5 3.3 3.3 Max 5.25 5.25 5.25 85 Unit V V V °C ABSOLUTE MAXIMUM RATINGS Parameter DC Power Supplies Symbol Logic Core VDDCORE PLL VDDPLL I/O VDDPAD (Note 1) (Note 1) (Note 1) IIN IIN IOUT PDN VIND TA TSTG Min -0.3 -0.3 -0.3 -0.3 -40 -65 Max 6.0 6.0 6.0 ±10 ±50 ±25 500 VDD+0.3 85 150 Units V V V mA mA mA mW V °C °C Input Current, Any Pin Except Supplies Input Current, Power Supplies Output Current Power Dissipation Digital Input Voltages Ambient Operating Temperature (Power Applied) Storage Temperature Range 1. Transient currents up to 100 mA will not cause SCR latch-up. DS639F2 12 CS5378 THERMAL CHARACTERISTICS Parameter Allowable Junction Temperature Junction to Ambient Thermal Impedance (4-Layer PCB) Ambient Operating Temperature (Power Applied) Symbol TJ ΘJA TA Min -40 Typ 50 +85 Max 135 Unit °C °C / W °C DIGITAL CHARACTERISTICS Parameter High-Level Input Drive Voltage Low-Level Input Drive Voltage High-Level Output Drive Voltage Low-Level Output Drive Voltage Rise Times, Digital Inputs Fall Times, Digital Inputs Rise Times, Digital Outputs Fall Times, Digital Outputs Input Leakage Current 3-State Leakage Current Digital Input Capacitance Digital Output Pin Capacitance (Note 2) Iout = -40 µA Iout = +40 µA Symbol VIH VIL VOH VOL tRISE tFALL tRISE tFALL IIN IOZ CIN COUT Min 0.6 * VDD 0.0 VDD - 0.3 0.0 Typ ±1 9 9 Max VDD 0.8 VDD 0.3 100 100 100 100 ± 10 ± 10 Unit V V V V ns ns ns ns µA µA pF pF Notes: 2. Maximum leakage for pins with pull-up resistors (RESET, SS:EECS, GPIO, MOSI, SCK) is ±250 µA. t rise out t fallo ut t ris e in t fa llin 0.90 * VDD 2.6 V 0.10 * VDD 0.7 V 0.90 * VDD 4 .6 V 0.10 * 0 .4 V VDD POWER CONSUMPTION Parameter Operational Power Consumption 1.024 MHz Digital Filter Clock 2.048 MHz Digital Filter Clock 4.096 MHz Digital Filter Clock 8.192 MHz Digital Filter Clock Standby Power Consumption 32 kHz Digital Filter Clock, Filter Stopped PWRS 100 µW PWR1 PWR2 PWR4 PWR8 12 14 16 24 mW mW mW mW Symbol Min Typ Max Unit DS639F2 13 CS5378 SWITCHING CHARACTERISTICS Serial Configuration Interface Timing (External Master) SSI SS:EECS MOSI MSB t1 MSB - 1 t2 t3 t4 t5 LSB t6 SCK SCLK Figure 4. MOSI Write Timing in SPI Slave Mode SS I SS:EECS t 10 MISO MSB t7 MSB - 1 t8 t9 LSB SCK SCLK Figure 5. MISO Read Timing in SPI Slave Mode Parameter MOSI Write Timing SS:EECS Enable to Valid Latch Clock Data Set-up Time Prior to SCK Rising Data Hold Time After SCK Rising SCK High Time SCK Low Time SCK Falling Prior to SS:EECS Disable MISO Read Timing SCK Falling to New Data Bit SCK High Time SCK Low Time SS:EECS Rising to MISO Hi-Z Symbol t1 t2 t3 t4 t5 t6 t7 t8 t9 t10 Min 60 60 120 120 120 60 120 120 - Typ - Max 60 150 Unit ns ns ns ns ns ns ns ns ns ns DS639F2 14 CS5378 SWITCHING CHARACTERISTICS Serial Data Interface Timing DRDY SCK t3 t4 MISO t1 t2 t5 Figure 6. Serial Data Read Timing Parameter DRDY Falling Edge to SCK Rising SCK Falling to New Data Bit SCK High Time SCK Low Time Final SCK Falling to DRDY Rising Symbol t1 t2 t3 t4 t5 Min 60 120 120 60 Typ - Max 120 - Unit ns ns ns ns ns DS639F2 15 CS5378 SWITCHING CHARACTERISTICS CLK, SYNC, MCLK, MSYNC, and MDATA SYNC MCLK MSYNC tmsd MDATA tmsh tmsd Data1 Data2 Note: SYNC input latched on MCLK rising edge. MSYNC output triggered by MCLK falling edge. fMCLK 2.048 MHz 1.024 MHz tmsd = TMCLK / 4 tmsh = TMCLK tmsd = 122 ns tmsh = 488 ns tmsd = 244 ns tmsh = 976 ns Figure 7. SYNC, MCLK, MSYNC, MDATA Interface Timing Parameter Master Clock Frequency Master Clock Duty Cycle Master Clock Rise Time Master Clock Fall Time Master Clock Jitter Synchronization after SYNC rising MSYNC Setup Time to MCLK rising MCLK rising to Valid MDATA MSYNC falling to MCLK rising (Note 4) (Note 3) Symbol CLK DTY tRISE tFALL JTR SYNC tmss tmdv tmsf Min 32 40 -2 20 20 Typ 32.768 - Max 33 60 20 20 300 2 75 - Unit MHz % ns ns ps µs ns ns ns Notes: 3. PLL bypass mode. The PLL generates a 32.768 MHz master clock when enabled. 4. Sampling synchronization between multiple CS5378 devices receiving identical SYNC signals. DS639F2 16 CS5378 SWITCHING CHARACTERISTICS Test Bit Stream (TBS) TBSDATA t1 t2 MCLK Note: Example timing shown for a 256 kHz output rate and no programmable delays. Figure 8. TBS Output Data Timing Parameter TBS Data Output Timing TBS Data Bit Rate TBS Data Rising to MCLK Rising Setup Time MCLK Rising to TBS Data Falling Hold Time (Note 5) Symbol Min - Typ 256 - Max - Unit kbps ns ns t1 t2 60 60 5. TBSDATA can be delayed from 0 to 63 full bit periods. The timing diagram shows no TBSDATA delay. DS639F2 17 CS5378 CS5373A Differential Sensor CS3301A CS3302A AMP CS5378 ∆Σ Modulator µController or Configuration EEPROM M U X Digital Filter System Telemetry Test DAC Figure 9. Single-Channel System Block Diagram 3. SYSTEM DESIGN WITH CS5378 Figure 9 illustrates a simplified block diagram of the CS5378 in a single channel measurement system. A differential sensor is connected through the CS3301A/02A differential amplifiers to the CS5373A ∆Σ modulator, where analog to digital conversion occurs. The modulator’s 1-bit output connects to the CS5378 MDATA input, where the oversampled ∆Σ data is decimated and filtered to 24-bit output samples at a programmed output rate. These output samples are buffered into an 8-deep data FIFO and then passed to the system telemetry. System self tests are performed by connecting the CS5378 test bit stream (TBS) generator to the CS5373A test DAC. Analog tests drive differential signals from the CS5373A test DAC into the multiplexed inputs of the CS3301A/02A amplifiers or directly to the differential sensor. Digital loopback tests internally connect the TBS digital output directly to the CS5378 modulator input. 3.1 Power Supplies The system shown in Figure 9 typically operates from a ±2.5 V analog power supply and a 3.3 V digital power supply. The CS5378 logic core can be powered from 2.5 V to minimize power consumption, if required. 3.2 Reset Control System reset is required only for the CS5378 device, and is a standard active low signal that can be generated by a power supply monitor or microcontroller. Other system devices default to a powerdown state when the CS5378 is reset. 3.3 PLL and Clock Generation A PLL is included on the CS5378 to generate an internal 32.768 MHz master clock from a 1.024 MHz, 2.048 MHz, or 4.096 MHz standard clock or Manchester encoded input. Clock inputs for other system devices are driven by clock outputs from the CS5378. DS639F2 18 CS5378 3.4 Synchronization Digital filter phase and analog sample timing of the ∆Σ modulator connected to the CS5378 are synchronized by a rising edge on the SYNC pin. If a synchronization signal is received identically by all CS5378 devices in a measurement network, synchronous sampling across the network is guaranteed. 3.7 Data Collection Data is collected from the CS5378 through the serial data interface. When data is available, serial transactions are automatically initiated to transfer 24-bit data or 32-bit status+data from the output FIFO to the system telemetry. The output FIFO has eight data locations to permit latency in data collection. 3.5 System Configuration Through the serial configuration interface, filter coefficients and digital filter register settings can either be programmed by a microcontroller or automatically loaded from an external EEPROM after reset. System configuration is only required for the CS5378 device, as other devices are configured via the CS5378 General Purpose I/O pins. Two registers in the digital filter, SYSTEM1 and SYSTEM2 (0x2C, 0x2D), are provided for user defined system information. These are general purpose registers that will hold any 24-bit data values written to them. 3.8 Integrated peripherals Test Bit Stream (TBS) A digital signal generator built into the CS5378 produces a 1-bit ∆Σ sine wave. This digital test bit stream is connected to the CS5373A test DAC to create high quality analog test signals or internally looped back to the CS5378 MDATA input to test the digital filter and data collection circuitry. Time Break Timing information is recorded during data collection by strobing the TIMEB pin. A dedicated flag in the sample status bits, TB, is set high to indicate during which measurement the timing event occurred. 3.6 Digital Filter Operation After analog to digital conversion occurs in the modulator, the oversampled 1-bit ∆Σ data is read into the CS5378 through the MDATA pin. The digital filter then processes data through the enabled filter stages, decimating it to 24-bit words at a programmed output word rate. The final 24-bit samples are concatenated with 8-bit status words and placed into an output FIFO. General Purpose I/O (GPIO) Eight general purpose pins are available on the CS5378 for system control. Each pin can be set as input or output, high or low, with an internal pullup enabled or disabled. The CS3301A/02A and CS5373A devices in Figure 9 are configured by simple pin settings controlled through the CS5378 GPIO pins. DS639F2 19 CS5378 1 2 3 4 5 6 7 8 28 27 26 25 24 23 22 21 20 19 18 17 16 15 GNDCORE VDDCORE VDDPAD GNDPAD 9 10 11 12 13 14 GNDPLL VDDPLL Figure 10. Power Supply Block Diagram 4. POWER SUPPLIES The CS5378 has three sets of power supply inputs. One set supplies power to the I/O pins of the device (VDDPAD), another supplies power to the logic core (VDDCORE) and the third supplies power to the PLL (VDDPLL). The I/O pin power supplies determine the maximum input and output voltages when interfacing to peripherals, the logic core power supply largely determines the power consumption of the CS5378 and the PLL power supply powers the internal PLL circuitry. VDDCORE, GNDCORE - Pins 21, 22 Sets the operational voltage of the CS5378 logic core. VDDCORE can be driven with voltages from 2.5 V to 5 V. A 2.5 V supply will minimize total power consumption. 4.2 Bypass Capacitors Each power supply pin should be bypassed with parallel 1 µF and 0.01 µF caps, or by a single 0.1 µF cap, placed as close as possible to the CS5378. Bypass capacitors should be ceramic (X7R, C0G), tantalum, or other good quality dielectric type. 4.1 Pin Descriptions VDDPAD, GNDPAD - Pins 9, 10 Sets the interface voltage to a microcontroller, system telemetry, modulator, and test DAC. VDDPAD can be driven with voltages from 3.3 V to 5 V. 4.3 Power Consumption Power consumption of the CS5378 depends primarily on the power supply voltage of the logic core (VDDCORE) and the programmed digital filter clock rate. Digital filter clock rates are selected based on the required output word rate as explained in “Digital Filter Initialization” on page 38. VDDPLL, GNDPLL - Pins 15, 16 Sets the operational voltage of the internal CS5378 PLL circuitry. Can be driven with voltages from 3.3 V to 5 V. DS639F2 20 CS5378 RESET Self-Tests BOOT Pin 1 0 SELFTEST Register EEPROM Boot µController Boot Figure 11. Reset Control Block Diagram 5. RESET CONTROL The CS5378 reset signal is active low. When released, a series of self-tests are performed and the device either actively boots from an external EEPROM or enters an idle state waiting for microcontroller configuration. combined into the SELFTEST register (0x2F), with 0x0AAAAA indicating all passed. Self-tests require 60 ms to complete. 5.3 Boot Configurations The logic state of the BOOT pin after reset determines if the CS5378 actively reads configuration information from EEPROM or enters an idle state waiting for a microcontroller to write configuration commands. 5.1 Pin Descriptions RESET - Pin 18 Reset input, active low. GPIO7:BOOT - Pin 28 Boot mode select, latched immediately following reset. Weak (~100 kΩ) internal pull-up defaults high, external 10 kΩ pull-down required to set low. BOOT 1 0 Reset Mode EEPROM boot Microcontroller boot EEPROM Boot When the BOOT pin is high after reset, the CS5378 actively reads data from an external serial EEPROM and then begins operation in the specified configuration. Configuration commands and data are encoded in the EEPROM as specified in the ‘Configuration By EEPROM’ section of this data sheet, starting on page 25. 5.2 Reset Self-Tests After RESET is released but before booting, a series of digital filter self-tests are run. Results are Self-Test Type Program ROM Data ROM Program RAM Data RAM Execution Unit DS639F2 Pass Code 0x00000A 0x0000A0 0x000A00 0x00A000 0x0A0000 Fail Code 0x00000F 0x0000F0 0x000F00 0x00F000 0x0F0000 Microcontroller Boot When the BOOT pin is low after reset, the CS5378 enters an idle state waiting for a microcontroller to write configuration commands and initialize filter operation. Configuration commands and data are written as specified in the ‘Configuration By Microcontroller’ section of this data sheet, starting on page 30. 21 CS5378 CLK PLL PLL[2:0] 32.768 MHz Clock Divider and MCLK Generator Internal Clocks MCLK Output DSPCFG Register Figure 12. Clock Generation Block Diagram 6. PLL AND CLOCK GENERATION The CS5378 requires a 32.768 MHz master clock, which can be supplied directly or from an internal phase locked loop. This master clock is used to generate an internal digital filter clock and an external modulator clock. The internal PLL will lock to standard clock or Manchester encoded input signals. The input type and input frequency are selected by the reset state of the PLL mode select pins. A weak internal pull-up resistor (~100 kΩ) will hold the PLL mode select pins high by default. To force the pin low on reset, an external 10 kΩ pulldown resistor should be connected. Once the pin state is latched following reset, the GPIO[4:6] pins function without affecting PLL operation. 6.3 Synchronous Clocking To guarantee synchronous measurements throughout a sensor network, a system clock should be distributed to arrive at all nodes in phase. The distributed system clock can either be the full 32.768 MHz master clock, or the CS5378 PLL can create a synchronous 32.768 MHz clock from a slower clock. To ensure the generated clock remains synchronous with the network, the CS5378 PLL uses a phase/frequency detector architecture. PLL[2:0] 111 110 101 100 011 010 001 000 6.1 Pin Descriptions CLK - Pin 17 Clock or PLL input, standard clock or Manchester. GPIO[4:6]:PLL[0:2] - Pins 5, 6, 7 PLL mode select, latched immediately after reset. Weak (~100 kΩ) internal pull-ups default high, external 10 kΩ pull-downs required to set low. PLL Mode 32.768 MHz clock input (PLL bypass). 1.024 MHz clock input. 2.048 MHz clock input. 4.096 MHz clock input. 32.768 MHz clock input (PLL bypass). 1.024 MHz Manchester input. 2.048 MHz Manchester input. 4.096 MHz Manchester input. 6.2 PLL Mode Select The CS5378 PLL operational mode and frequency are selected immediately after reset based on the state of the PLL[0:2] pins. On the rising edge of the reset signal, the digital high or low state of the PLL[0:2] pins is latched and used to program the clock input type and frequency. Table 5. PLL Mode Selections DS639F2 22 CS5378 6.4 Master Clock Jitter and Skew Care must be taken to minimize jitter and skew on the distributed system clock as both parameters affect measurement performance. Jitter on the input clock causes jitter in the generated modulator clock, resulting in sample timing errors and increased noise. Skew between input clocks from node to node creates a sample timing offset, resulting in systematic measurement errors in a reconstructed signal. DS639F2 23 CS5378 0 SYNC 1 MSYNC Generator Digital Filter 0 1 Test Bit Stream MSEN MSYNC Output TSYNC Figure 13. Synchronization Block Diagram 7. SYNCHRONIZATION The CS5378 has a dedicated SYNC input that aligns the internal digital filter phase and generates an external signal for synchronizing modulator analog sampling. By providing simultaneous rising edges to the SYNC pins of multiple CS5378 devices, synchronous sampling across a network can be guaranteed. phase. Filter convolutions restart, and the next output word is available one full sample period later. Repetitive synchronization is supported when SYNC events occur at exactly the selected output rate. In this case, re-synchronization will occur at the start of a convolution cycle when the digital filter state machine is already reset. 7.1 Pin Description SYNC - Pin 19 Synchronization input, rising edge triggered. 7.4 Modulator Synchronization 7.2 MSYNC Generation The SYNC signal rising edge is used to generate a retimed synchronization signal, MSYNC. The MSYNC signal reinitializes internal digital filter phase and is driven onto the MSYNC output pin to phase align modulator analog sampling. The MSEN bit in the digital filter CONFIG register (0x00) enables MSYNC generation. See “Modulator Interface” on page 36 for more information about MSYNC. The external MSYNC signal phase aligns modulator analog sampling when connected to the CS5373A MSYNC input. This ensures synchronous analog sampling relative to MCLK. Repetitive synchronization of the modulators is supported when SYNC events occur at exactly the selected output rate. In this case, re-synchronization always occurs at the start of analog sampling. 7.5 Test Bit Stream Synchronization When the test bit stream generator is enabled, an MSYNC signal can reset the internal data pointer. This restarts the test bit stream from the first data point to establish a known output signal phase. The TSYNC bit in the digital filter TBSCFG register (0x2A) enables synchronization of the test bit stream by MSYNC. When TSYNC is disabled, the test bit stream phase is not affected by MSYNC. 7.3 Digital Filter Synchronization The internal MSYNC signal resets the digital filter state machine to establish a known digital filter DS639F2 24 CS5378 VD 3 8 7 WP VCC HOLD SS:EECS SCK 27 24 25 26 1 6 2 5 CS SCK CS5378 MISO MOSI AT25640 SO SI 4 GND Figure 14. EEPROM Configuration Block Diagram 8. CONFIGURATION BY EEPROM After reset, the CS5378 reads the state of the GPIO7:BOOT pin to determine a source for configuration commands. If BOOT is high, the CS5378 initiates serial transactions to read configuration information from an external EEPROM. to read configuration commands and data. 8-bit SPI opcodes and 16-bit addresses are combined to read back 8-bit configuration commands and 24-bit configuration data. System design should include a connection to the configuration EEPROM for in-circuit reprogramming. The CS5378 serial pins tri-state when inactive to support external connections to the serial bus. 8.1 Pin Descriptions Pins required for EEPROM boot are listed here, other serial pins are inactive. SCK - Pin 24 Serial clock output, nominally 1.024 MHz. 8.3 EEPROM Organization The boot EEPROM holds the 8-bit commands and 24-bit data required to initialize the CS5378 into an operational state. Configuration information starts at memory location 0x10, with addresses 0x00 to 0x0F free for use as manufacturing header information. The first serial transaction reads a 1-byte command from memory location 0x10 and then, depending on the command type, reads multiple 3-byte data words to complete the command. Command and data reads continue until the ‘Filter Start’ command is recognized. MISO - Pin 25 Serial data input pin. Valid on rising edge of SCK, transition on falling edge. MOSI - Pin 26 Serial data output pin. Valid on rising edge of SCK, transition on falling edge. SS:EECS - Pin 27 EEPROM chip select output, active low. 8.2 EEPROM Hardware Interface When booting from EEPROM the CS5378 actively performs serial transactions, as shown in Figure 15, DS639F2 25 CS5378 Instruction Read 0x03 Opcode Address ADDR[15:0] Definition Read data beginning at the address given in ADDR. Serial Read from EEPROM READ CMD MOSI 0x03 2 BYTE ADDR ADDR ADDR MISO DATA1 DATA2 DATA3 1 BYTE / 3 BYTE DATA SS:EECS Cycle 1 2 3 4 5 6 7 8 SCK MOSI MSB 6 5 4 3 2 1 LSB MISO MSB 6 5 4 3 2 1 LSB X SS:EECS Figure 15. EEPROM Serial Read Transactions DS639F2 26 CS5378 Write DF Register - 0x01 0000h 0010h Mfg Header 8-bit Command N x 24-bit Data 8-bit Command N x 24-bit Data 1FFFh ... EEPROM Manufacturing Information EEPROM Command and Data Values This EEPROM command writes a data value to the specified digital filter register. Digital filter registers control hardware peripherals and filtering functions. See “Digital Filter Registers” on page 71 for the bit definitions of the digital filter registers. Sample Command: Write digital filter register 0x00 with data value 0x060431. Then write 0x20 with data 0x000240. 01 00 00 00 06 04 31 01 00 00 20 00 02 40 Figure 16. 8 Kbyte EEPROM Memory Organization Write FIR Coefficients - 0x02 The maximum number of bytes that will be written for a single configuration is less than 2 KByte (16 Kbit), including command overhead: This EEPROM command writes custom coefficients for the FIR1 and FIR2 filters. The first two data words set the number of FIR1 and FIR2 coefficients to be written. The remaining data words are the concatenated FIR1 and FIR2 coefficients. A maximum of 255 coefficients can be written for each FIR filter, though the available digital filter computation cycles will limit their practical size. See “FIR Filter” on page 44 for more information about FIR filter coefficients. Memory Requirement Bytes Digital Filter Registers (12) FIR Coefficients (255+255) IIR Coefficients (3+5) ‘Filter Start’ Command Total Bytes 84 1537 25 1 1647 Sample Command: Write FIR1 coefficients 0x00022E, 0x000771 then FIR2 coefficients 0xFFFFB9, 0xFFFE8D. Table 6. Maximum EEPROM Configuration 02 00 00 02 00 00 02 00 02 2E 00 07 71 FF FF B9 FF FE 8D Supported serial configuration EEPROMs are SPI mode 0 (0,0) compatible, 16-bit addresses, 8bit data, larger than 2 KByte (16 KBit). ATMEL AT25640, AT25128, or similar serial EEPROMs are recommended. Write IIR Coefficients - 0x03 This EEPROM command writes custom coefficients for the two stage IIR filter. The IIR architecture and number of coefficients is fixed, so eight data words containing coefficient values always immediately follow the command byte. The IIR coefficient write order is: a11, b10, b11, a21, a22, b20, b21, and b22. See “IIR Filter” on page 52 for more information about IIR filter coefficients. 8.4 EEPROM Configuration Commands A summary of available EEPROM commands is shown in Table 7. DS639F2 27 CS5378 Sample Command: Write IIR1 coefficients 0x84BC9D, 0x7DA1B1, 0x825E4F, and IIR2 coefficients 0x83694F, 0x3CAD5F, 0x3E5104, 0x835DF8, 0x3E5104. 03 84 BC 9D 7D A1 B1 82 5E 4F 83 69 4F 3C AD 5F 3E 51 04 83 5D F8 3E 51 04 Sample Command: Select IIR1 and IIR2 3 Hz @ 500 SPS low-cut coefficients, with FIR1 and FIR2 linear phase highcut coefficients. Data word 0x002200. 04 00 22 00 Filter Start - 0x07 This EEPROM command initializes and starts the digital filter. Measurement data becomes available one full sample period after this command is issued. No data words are required for this EEPROM command. Write ROM Coefficients - 0x04 This EEPROM command selects the on-chip coefficients for the FIR1, FIR2, IIR 1st order, and IIR 2nd order filters for use by the digital filter. One data word is required to select which internal coefficient sets to use. See “Filter Coefficient Selection” on page 38 for information about selecting on-chip FIR and IIR coefficient sets. Sample Command: 07 Name NOP WRITE DF REGISTER WRITE FIR COEFFICIENTS CMD 8-bit 00 01 02 DATA 24-bit REG DATA NUM FIR1 NUM FIR2 (FIR COEF) a11 b10 b11 a21 a22 b20 b21 b22 COEF SEL No Operation Description Write Digital Filter Register Write Custom FIR Coefficients WRITE IIR COEFFICIENTS 03 Write Custom IIR Coefficients WRITE ROM COEFFICIENTS NOP NOP FILTER START 04 05 06 07 Use On-Chip Coefficients No Operation No Operation Start Digital Filter Operation (DATA) indicates multiple words of this type are to be written. Table 7. EEPROM Boot Configuration Commands DS639F2 28 CS5378 8.5 Example EEPROM Configuration Table 8 shows an example EEPROM file for a minimal CS5378 configuration. Addr 00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F Data 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 04 00 22 00 01 00 00 00 06 04 31 01 00 00 20 00 Description Mfg header Addr 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 30 Data 02 40 01 00 00 2A 07 40 40 01 00 00 2B 04 B0 00 07 Description Write TBSCFG Register Write TBSGAIN Register Write ROM Coefficients 31 Filter Start Write CONFIG Register Write FILTCFG Register Table 8. Example EEPROM File DS639F2 29 CS5378 Digital Filter Command Interpreter SPI™ Registers Serial Pin Logic SS:EECS SCK MOSI MISO Figure 17. Serial Interface Block Diagram 9. CONFIGURATION BY MICROCONTROLLER After reset, the CS5378 reads the state of the GPIO7:BOOT pin to determine a source for configuration commands. If BOOT is low, the CS5378 receives configuration commands from a microcontroller. 9.2 Microcontroller Hardware Interface When booting from a microcontroller the CS5378 receives configuration commands and configuration data through serial transactions, as shown in Figure 18. 8-bit SPI opcodes and 8-bit addresses are combined to read and write 24-bit configuration commands and data. Microcontroller serial transactions require toggling the SS:EECS pin as the CS5378 chip select and writing a serial clock to the SCK input. Serial data is input to the CS5378 on the MOSI pin, and output on the MISO pin. 9.1 Pin Descriptions Pins required for microcontroller boot are listed here, other serial pins are inactive. SS:EECS - Pin 27 Slave select input pin, active low. Serial chip select input from a microcontroller. MOSI - Pin 26 Serial data input pin. Valid on rising edge of SCK, transition on falling edge. 9.3 Microcontroller Serial Transactions Microcontroller configuration commands are written to the digital filter through SPI registers. A 24bit command and two 24-bit data words can be written to the SPI registers in any single serial transaction. Some commands require additional data words through additional serial transactions to complete. 9.3.1 SPI opcodes A microcontroller communicates with the CS5378 serial port using standard 8-bit SPI opcodes and an 8-bit address. The standard SPI ‘Read’ and ‘Write’ opcodes are listed in Figure 18. MISO - Pin 25 Serial data output pin. Valid on rising edge of SCK, transition on falling edge. Open drain output requiring a 10 kΩ pull-up resistor. SCK - Pin 24 Serial clock input pin. Serial clock input from microcontroller, maximum 4.096 MHz. DS639F2 30 CS5378 Instruction Write Read Opcode 0x02 0x03 Address ADDR[7:0] ADDR[7:0] Definition Write SPI registers beginning at the address in ADDR. Read SPI registers beginning at the address in ADDR. Microcontroller Write to SPI Registers SS:EECS MISO 0x02 ADDR Data1 Data2 DataN MOSI Microcontroller Read from SPI Registers SS:EECS MISO 0x03 ADDR MOSI Data1 Data2 DataN Cycle 1 2 3 4 5 6 7 8 SCK MOSI MSB 6 5 4 3 2 1 LSB MISO MSB 6 5 4 3 2 1 LSB X SS:EECS Figure 18. Microcontroller Serial Transactions DS639F2 31 CS5378 9.3.2 SPI registers The SPI registers are shown in Figure 19 and are 24-bit registers mapped into an 8-bit register space as high, mid, and low bytes. See “SPI Registers” on page 66 for the bit definitions of the SPI registers. 9.3.3 Serial transactions A serial transaction to the SPI registers starts with an SPI opcode, followed by an address, and then some number of data bytes written or read starting at that address. Typical serial write transactions require sending groups of 5, 8, or 11 total bytes to the SPICMD or SPIDAT1 registers: 5-byte write to SPICMD 02 03 12 34 56 5-byte write to SPIDAT1 02 06 12 34 56 8-byte write to SPICMD, SPIDAT1 02 03 12 34 56 AB CD EF 8-byte write to SPIDAT1, SPIDAT2 02 06 12 34 56 AB CD EF 11-byte write to SPICMD, SPIDAT1, SPIDAT2 02 03 12 34 56 AB CD EF 65 43 21 Typical serial read transactions require groups of 3 or 5 bytes, split between writing into MOSI and reading from MISO. 3-byte read of mid-byte of SPICTRL 9.3.5 Polling E2DREQ One transaction type that can always be performed no matter the delay from the previous configuration command is reading E2DREQ in the mid-byte of the SPICTRL register. A 3-byte read transaction. MOSI: 03 01 00 MISO: xx xx 01 EXP] YSUM(n) = Y(n) + YSUM(n-1) Offset Correction = YSUM >> EXP Once the EXP bits are written, the ORCAL bit in the FILTCFG register is set to enable offset calibration. When enabled, an updated offset correction value is automatically written to the OFFSET register. When the offset calibration algorithm is fully settled, the ORCAL bit should be cleared to maintain the final value in the OFFSET register. 15.3 Offset Calibration An offset calibration algorithm in the CS5378 can automatically calculate an offset correction value. When using the offset calibration algorithm, background noise data should be used as the input signal for calculating the offset of the measurement channel. The offset calibration algorithm is an exponential averaging function that places increased weight on more recent digital filter data. The exponential weighting factor is set by the EXP bits in the DS639F2 57 CS5378 System Telemetry Data Ready Clock Out Data In CS5378 DRDY SCK MISO Figure 33. Serial Data Interface Block Diagram 16. SERIAL DATA INTERFACE Once digital filtering is complete, each 24-bit output sample is combined with an 8-bit status byte. These data words are written to an 8-deep FIFO buffer and then transmitted to the communications channel through a high speed serial data interface. MISO - Pin 25 Serial data output. 16.2 Serial Data Format Serial data transactions transfer either 24-bit data words or 32-bit status+data words, depending on the STAT bit in the CONFIG register. When transmitting status information, each 8-bit status byte has an MFLAG bit, a time break bit, and a FIFO overflow bit encoded as shown in Figure 34. 16.1 Pin Descriptions DRDY - Pin 23 Data ready output signal, active low. Open drain output requiring an external pull-up resistor. SCK - Pin 24 Serial clock input. MFLAG Bit - MFLAG The MFLAG bit is set in the status byte when an signal is received on the MFLAG pin. When re- 31 Status 23 Data 0 MFLAG 31 -30 -29 -28 -27 TB 26 -25 W 24 0 - Modulator Ok 1 - Modulator Error 0 - No Time Break 1 - Time Break 0 - FIFO Ok 1 - FIFO Overflow Figure 34. 32-bit Serial Data Format DS639F2 58 CS5378 ceived, the MFLAG bit is set in the next output word. See “Modulator Interface” on page 36 for more information about MFLAG. The W bit is sticky, meaning it persists indefinitely once set. Clearing the W bit requires sending the ‘Filter Stop’ and ‘Filter Start’ configuration commands to reinitialize the data FIFO. Time Break Bit - TB The time break bit marks a timing reference based on a rising edge into the TIMEB pin. After a programmed delay, the TB bit in the status byte is set for one output sample. The TIMEBRK digital filter register (0x29) programs the sample delay for the TB bit output. See “Time Break Controller” on page 63 for more information about time break. Conversion Data Word The lower 24-bits of the serial data word is the conversion sample for the specified channel. Conversion data is 24-bit two’s complement format. 16.3 Serial Data Transactions The CS5378 automatically initiates serial data transactions whenever data becomes available in the output FIFO by driving the DRDY pin low. Once a serial data transaction is initiated, serial clocks received into SCK cause data to be output to MISO, as shown in Figure 35. When all available data is read from the serial data FIFO, DRDY is released. FIFO Overflow Bit - W The FIFO overflow bit indicates an error condition in the serial data FIFO, and is set if new digital filter data overwrites a FIFO location containing data which has not yet been sent. DRDY SCK MISO MSB LSB Figure 35. SD Port Transaction DS639F2 59 CS5378 Digital Filter Data Bus 24-bit TBSGAIN Register 24-bit Digital ∆Σ Modulator 1-bit TBSDATA Figure 36. Test Bit Stream Generator Block Diagram 17. TEST BIT STREAM GENERATOR The CS5378 test bit stream (TBS) generator creates sine wave ∆Σ bit stream data to drive an external test DAC. The TBS digital output can also be internally connected to the MDATA inputs for loopback testing of the digital filter. 17.3 TBS Configuration Configuration options for the TBS generator are set through the TBSCFG register (0x2A). Gain scaling of the TBS generator output is set by the TBSGAIN register (0x2B). 17.1 Pin Descriptions TBSDATA - Pin 8 Test bit stream 1-bit ∆Σ data output. Interpolation Factor - INTP[7:0] Selects how many times the interpolator uses a data point when generating the output bit stream. Interpolation is zero based and represents one greater than the programmed register value. MCLK - Pin 11 Test bit stream clock output. Output Rate - RATE[2:0] Selects the TBSDATA output rate. 17.2 TBS Architecture The test bit stream generator consists of a data interpolator and a digital ∆Σ modulator. It receives periodic 24-bit data from the digital filter to create a 1-bit ∆Σ data output on the TBSDATA pin. The TBS input data from the digital filter is scaled by the TBSGAIN register (0x2B). Maximum stable amplitude is 0x04FFFF, with 0x04B000 approximately full scale for the CS5373A test DAC. The full scale 1-bit ∆Σ output from the TBS generator is defined as 25% minimum and 75% maximum one’s density. DS639F2 Synchronization - TSYNC Enables synchronization of the TBS output phase to the MSYNC signal. Loopback - LOOP Enables digital loopback from the TBS output to the MDATA inputs. Run - RUN Enables the test bit stream generator. 60 CS5378 Test Bit Stream Characteristic Equation: (Signal Freq) * (# TBS Data) * (Interpolation + 1) = Output Rate Example: (31.25 Hz) * (1024) * (0x07 + 1) = 256 kHz Signal Frequency (TBSDATA) 10.00 Hz 10.00 Hz 25.00 Hz 25.00 Hz 31.25 Hz 31.25 Hz 50.00 Hz 50.00 Hz 125.00 Hz 125.00 Hz Output Rate (TBSCLK) 256 kHz 512 kHz 256 kHz 512 kHz 256 kHz 512 kHz 256 kHz 512 kHz 256 kHz 512 kHz Output Rate Selection (RATE) 0x4 0x5 0x4 0x5 0x4 0x5 0x4 0x5 0x4 0x5 Interpolation Selection (INTP) 0x18 0x31 0x09 0x13 0x07 0x0F 0x04 0x09 0x01 0x03 Table 18. TBS Configurations Using On-chip Data Data Delay - DDLY[5:0] Programs full period delays for TBSDATA, up to a maximum of 63 bits. 17.5 TBS Sine Wave Output The TBS generator uses data from digital filter memory to create a sine wave test signal that can drive a test DAC. Sine wave frequency and output data rate are calculated as shown by the characteristic equation of Table 18. The sine wave maximum ∆Σ one’s density output from the TBS generator is set by the TBSGAIN register. TBSGAIN can be programmed up to a maximum of 0x04FFFF, with the TBS generator unstable for higher amplitudes. For the CS5373A test DAC, a gain value of 0x04B000 produces an approximately full scale sine wave output (5 Vpp differential). Gain - TBSGAIN[23:0] Scales the amplitude of the sine wave output. Maximum 0x04FFFF, nominal 0x04B000. 17.4 TBS Data Source An on-chip 24-bit 1024 point digital sine wave is stored on the CS5378 which will produce the test signal frequencies listed in Table 18. Additional discrete test frequencies and output rates can be programmed by varying the interpolation factor and output rate. DS639F2 61 CS5378 17.6 TBS Loopback Testing Included as part of the CS5378 test bit stream generator is a feedback path to the digital filter MDATA input. This loopback mode provides a fully digital signal path to test the TBS generator, digital filter, and data collection interface. Digital loopback testing expects 512 kHz ∆Σ data into the MDATA input. A mismatch of the TBS generator full scale output and the MDATA full scale input results in an amplitude mismatch when testing in loopback mode. The TBS generator outputs a 75% maximum one’s density, while the MDATA inputs expect an 86% maximum one’s density from a ∆Σ modulator, resulting in a measured full scale error of approximately -3.6 dB. 17.7 TBS Synchronization When the TSYNC bit is set in the TBSCFG register, the MSYNC signal resets the sine wave data pointer and phase aligns the TBS signal output. Once the digital filter is settled, all CS5378 devices receiving the SYNC signal will have identical TBS signal phase. See “Synchronization” on page 24 for more information about the SYNC and MSYNC signals. If TSYNC is clear, MSYNC has no effect on the TBS data pointer and no change in the TBS output phase will occur during synchronization. DS639F2 62 CS5378 TIMEB TIMEBRK Delay Counter TB Flag in Serial Data Status Byte Figure 37. Time Break Block Diagram 18. TIME BREAK CONTROLLER A time break signal is used to mark timing events that occur during measurement. An external signal sets a flag in the status byte of an output sample to mark when the external event occurred. A rising edge input to the TIMEB pin causes the TB timing reference flag to be set in the serial data status byte. When set, the TB flag appears for only one output sample in the status byte. The TB flag output can be delayed by programming a sample delay value into the TIMEBRK digital filter register. 18.3 Time Break Delay The TIMEBRK register (0x29) sets a sample delay between a received rising edge on the TIMEB pin and writing the TB flag into the serial data status byte. The programmable sample counter can compensate for group delay through the digital filters. When the proper group delay value is programmed into the TIMEBRK register, the TB flag will be set in the status byte of the measurement sample taken when the timing reference signal was received. 18.3.1 Step Input and Group Delay A simple method to empirically measure the step response and group delay of a CS5378 measurement channel is to use the time break signal as both a timing reference input and an analog step input. 18.1 Pin Description TIMEB - Pin 20 Time break input pin, rising edge triggered. 18.2 Time Break Operation An externally generated timing reference signal applied to the TIMEB pin initiates an internal sample counter. After a number of output samples have passed, programmed in the TIMEBRK digital filter register (0x29), the TB flag is set in the status byte of the serial data output word. The TB flag is automatically cleared for subsequent data words, and appears for only one output sample. When a rising edge is received on the TIMEB pin with no delay programmed into the TIMEBRK register, the TB flag is set in the next serial data status byte. The same rising edge can act as a step input to the analog channel, propagating through the digital filter to appear as a rising edge in the measurement data. By comparing the timing of the TB status flag output and the rising edge in the measurement data, the measurement channel group delay can be determined. DS639F2 63 CS5378 GP_PULL Pull Up Logic R GP_DATA GPIO GP_DIR Figure 38. GPIO Block Diagram 19. GENERAL PURPOSE I/O The General Purpose I/O (GPIO) block provides 8 general purpose pins to interface with external hardware. GP_PULL bits enable/disable the internal pull-up resistor, and GP_DATA bits set the output data value. After reset, GPIO pins default as inputs with pull-up resistors enabled. 19.1 Pin Descriptions GPIO[3:0] - Pins 4 - 1 Standard GPIO pins. 19.4 GPIO Input Mode When reading a value from the GP_DATA bits, the returned data reports the current state of the pins. If a pin is externally driven high it reads a logical 1, if externally driven low it reads a logical 0. When a GPIO pin is used as an input, the pull-up resistor should be disabled to save power if it isn’t required. GPIO[6:4]:PLL[2:0] - Pins 7 - 5 Standard GPIO pins also used to select the PLL mode after reset. Internal pull-ups default high, 10 kΩ external pull-downs required to set low. GPIO7:BOOT - Pin 28 Standard GPIO pin also used to select boot mode after reset. Internal pull-up defaults high, 10 kΩ external pull-down required to set low. 19.5 GPIO Output Mode When a GPIO pin is programmed as an output with a data value of 0, the pin is driven low and the internal pull-up resistor is automatically disabled. When programmed as an output with a data value of 1, the pin is driven high and the pull-up resistor is inconsequential. Any GPIO pin can be used as an open-drain output by setting the data value to 0, enabling the pull-up, and using the GP_DIR direction bits to control the pin value. This open-drain output configuration uses the internal pull-up resistor to hold the pin high when GP_DIR is set as an input, and drives the pin low when GP_DIR is set as an output. 19.2 GPIO Architecture Each GPIO pin can be configured as input or output, high or low, with a weak (~100 kΩ) internal pull-up resistor enabled or disabled. Figure 38 shows the structure of a bi-directional GPIO pin. 19.3 GPIO Registers GPIO pin settings are programmed in the GPCFG register. GP_DIR bits set the input/output mode, DS639F2 64 CS5378 19.5.1 GPIO Reads in Output Mode When reading GPIO pins the GP_DATA register value always reports the current state of the pins, so a value written in output mode does not necessarily read back the same value. If a pin in output mode is written as a logical 1, the CS5378 attempts to drive the pin high. If an external device forces the pin low, the read value reflects the pin state and returns a logical 0. Similarly, if an output pin is written as a logical 0 but forced high externally, the read value reflects the pin state and returns a logical 1. In both cases the CS5378 is in contention with the external device resulting in increased power consumption. DS639F2 65 CS5378 20. REGISTER SUMMARY 20.1 SPI Registers The CS5378 SPI registers interface the serial port to the digital filter. Name Addr. Type # Bits Description SPICTRLH SPICTRLM SPICTRLL SPICMDH SPICMDM SPICMDL SPIDAT1H SPIDAT1M SPIDAT1L SPIDAT2H SPIDAT2M SPIDAT2L 00 01 02 03 04 05 06 07 08 09 0A 0B R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W 8 8 8 8 8 8 8 8 8 8 8 8 SPI Control Register, High Byte SPI Control Register, Middle Byte SPI Control Register, Low Byte SPI Command, High Byte SPI Command, Middle Byte SPI Command, Low Byte SPI Data 1, High Byte SPI Data 1, Middle Byte SPI Data 1, Low Byte SPI Data 2, High Byte SPI Data 2, Middle Byte SPI Data 2, Low Byte DS639F2 66 CS5378 20.1.1 SPICTRL : 0x00, 0x01, 0x02 Figure 39. SPI Control Register SPICTRL (MSB) 23 -R/W 0 22 -R/W1 0 21 -R/W 0 20 -R/W 0 19 -R/W 1 18 -R/W 0 17 -R/W 1 16 -R/W 1 SPI Address: 0x00 0x01 0x02 -15 SMODF R 0 14 -R/W 0 13 -R 0 12 EMOP R 0 11 SWEF R 0 10 -R/W 0 9 -R/W 1 8 E2DREQ R/W 0 R W R/W Not defined; read as 0 Readable Writable Readable and Writable 7 -R/W 0 6 -R/W 0 5 -R/W 1 4 -R/W 0 3 -R/W 0 2 -R/W 0 1 -R/W 0 (LSB) 0 -R/W 0 Bits in bottom rows are reset condition Bit definitions: 23:16 -reserved 15 SMODF SPI mode fault flag reserved External master to SPI operation in progress flag SPI write collision error flag reserved 7:0 -reserved 14:13 -12 EMOP 11 SWEF 10:9 8 -- E2DREQ External master to digital filter request flag DS639F2 67 CS5378 20.1.2 SPICMD : 0x03, 0x04, 0x05 Figure 40. SPI Command Register SPICMD (MSB) 23 SCMD23 R/W 0 22 SCMD22 R/W 0 21 SCMD21 R/W 0 20 SCMD20 R/W 0 19 SCMD19 R/W 0 18 SCMD18 R/W 0 17 SCMD17 R/W 0 16 SCMD16 R/W 0 SPI Address: 0x03 0x04 0x05 -15 SCMD15 R/W 0 14 SCMD14 R/W 0 13 SCMD13 R/W 0 12 SCMD12 R/W 0 11 SCMD11 R/W 0 10 SCMD10 R/W 0 9 SCMD9 R/W 0 8 SCMD8 R/W 0 R W R/W Not defined; read as 0 Readable Writable Readable and Writable 7 SCMD7 R/W 0 6 SCMD6 R/W 0 5 SCMD5 R/W 0 4 SCMD4 R/W 0 3 SCMD3 R/W 0 2 SCMD2 R/W 0 1 SCMD1 R/W 0 (LSB) 0 SCMD0 R/W 0 Bits in bottom rows are reset condition Bit definitions: 23:16 SCMD[23:16] SPI Command High 15:8 Byte SCMD[15:8] SPI Command Mid- 15:8 dle Byte SCMD[7:0] SPI Command Low Byte DS639F2 68 CS5378 20.1.3 SPIDAT1 : 0x06, 0x07, 0x08 Figure 41. SPI Data Register SPIDAT1 (MSB) 23 SDAT23 R/W 0 22 SDAT22 R/W 0 21 SDAT21 R/W 0 20 SDAT20 R/W 0 19 SDAT19 R/W 0 18 SDAT18 R/W 0 17 SDAT17 R/W 0 16 SDAT16 R/W 0 SPI Address: 0x06 0x07 0x08 -15 SDAT15 R/W 0 14 SDAT14 R/W 0 13 SDAT13 R/W 0 12 SDAT12 R/W 0 11 SDAT11 R/W 0 10 SDAT10 R/W 0 9 SDAT9 R/W 0 8 SDAT8 R/W 0 R W R/W Not defined; read as 0 Readable Writable Readable and Writable 7 SDAT7 R/W 0 6 SDAT6 R/W 0 5 SDAT5 R/W 0 4 SDAT4 R/W 0 3 SDAT3 R/W 0 2 SDAT2 R/W 0 1 SDAT1 R/W 0 (LSB) 0 SDAT0 R/W 0 Bits in bottom rows are reset condition Bit definitions: 23:16 SDAT[23:16] SPI Data High Byte 15:8 SDAT[15:8] SPI Data Middle Byte 15:8 SDAT[7:0] SPI Data Low Byte DS639F2 69 CS5378 20.1.4 SPIDAT2 : 0x09, 0x0A, 0x0B Figure 42. SPI Data Register SPIDAT2 (MSB) 23 SDAT23 R/W 0 22 SDAT22 R/W 0 21 SDAT21 R/W 0 20 SDAT20 R/W 0 19 SDAT19 R/W 0 18 SDAT18 R/W 0 17 SDAT17 R/W 0 16 SDAT16 R/W 0 SPI Address: 0x09 0x0A 0x0B -15 SDAT15 R/W 0 14 SDAT14 R/W 0 13 SDAT13 R/W 0 12 SDAT12 R/W 0 11 SDAT11 R/W 0 10 SDAT10 R/W 0 9 SDAT9 R/W 0 8 SDAT8 R/W 0 R W R/W Not defined; read as 0 Readable Writable Readable and Writable 7 SDAT7 R/W 0 6 SDAT6 R/W 0 5 SDAT5 R/W 0 4 SDAT4 R/W 0 3 SDAT3 R/W 0 2 SDAT2 R/W 0 1 SDAT1 R/W 0 (LSB) 0 SDAT0 R/W 0 Bits in bottom rows are reset condition Bit definitions: 23:16 SDAT[23:16] SPI Data High Byte 15:8 SDAT[15:8] SPI Data Middle Byte 15:8 SDAT[7:0] SPI Data Low Byte DS639F2 70 CS5378 20.2 Digital Filter Registers The CS5378 digital filter registers control hardware peripherals and filtering functions. Name Addr. Type # Bits Description CONFIG RESERVED GPCFG RESERVED FILTCFG GAIN RESERVED OFFSET RESERVED TIMEBRK TBSCFG TBSGAIN SYSTEM1 SYSTEM2 VERSION SELFTEST 00 01-0D 0E 0F-1F 20 21 22-24 25 26-28 29 2A 2B 2C 2D 2E 2F R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 24 Hardware Configuration Reserved GPIO[7:0] Direction, Pull-Up Enable, and Data Reserved Digital Filter Configuration Gain Correction Reserved Offset Correction Reserved Time Break Delay Test Bit Stream Configuration Test Bit Stream Gain User Defined System Register 1 User Defined System Register 2 Hardware Version ID Self-Test Result Code DS639F2 71 CS5378 20.2.1 CONFIG : 0x00 Figure 43. Hardware Configuration Register CONFIG (MSB)23 -R/W 0 22 -R/W 0 21 -R/W 0 20 -R/W 0 19 -R/W 0 18 DFS2 R/W 1 17 DFS1 R/W 0 16 DFS0 R/W 1 DF Address: 0x00 -R W R/W 15 -R/W 0 14 -R/W 0 13 -R/W 0 12 -R/W 0 11 -R/W 0 10 MCKFS2 R/W 1 9 MCKFS1 R/W 0 8 MCKFS0 R/W 0 Not defined; read as 0 Readable Writable Readable and Writable 7 STAT R/W 0 6 -R/W 0 5 -R/W 0 4 MCKEN R/W 0 3 MDIFS R/W 0 2 -R/W 0 1 BOOT R 0 (LSB)0 MSEN R/W 1 Bits in bottom rows are reset condition Bit definitions: 23:19 -reserved 15:11 -reserved 7:6 STAT Serial Data Status Byte 1: Disabled (24-bit output) 0: Enabled (32-bit output) reserved MCLK output enable 1: Enabled 0: Disabled MDATA input frequency select 1: 256 kHz 0: 512 kHz reserved Boot source indicator 1: Booted from EEPROM 0: Booted from Micro MSYNC enable 1: MSYNC generated 0: MSYNC remains low 18:16 DFS [2:0] Digital filter frequency select 111: Reserved 110: 8.192 MHz 101: 4.096 MHz 100: 2.048 MHz 011: 1.024 MHz 010: 512 kHz 001: 256 kHz 000: 32 kHz 10:8 MCKFS [2:0] MCLK frequency select 5 111: reserved 110: reserved 4 101: 4.096 MHz 100: 2.048 MHz 011: 1.024 MHz 010: 512 kHz 3 001: reserved 000: reserved -MCKEN MDIFS 2 1 -BOOT 0 MSEN DS639F2 72 CS5378 20.2.2 GPCFG : 0x0E Figure 44. GPIO Configuration Register GPCFG (MSB) 23 GP_DIR7 22 GP_DIR6 21 GP_DIR5 20 GP_DIR4 19 GP_DIR3 18 GP_DIR2 17 GP_DIR1 16 GP_DIR0 DF Address: 0x0E R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 R/W 0 -R W R/W 15 GP_PULL7 14 GP_PULL6 13 GP_PULL5 12 GP_PULL4 11 GP_PULL3 10 GP_PULL2 9 GP_PULL1 8 GP_PULL0 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 Not defined; read as 0 Readable Writable Readable and Writable 7 GP_DATA7 6 GP_DATA6 5 GP_DATA5 4 GP_DATA4 3 GP_DATA3 2 GP_DATA2 1 GP_DATA1 (LSB) 0 GP_DATA0 Bits in bottom rows are reset condition R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 R/W 1 Bit definitions: 23:16 GP_DIR [7:0] GPIO pin direction 1: Output 0: Input 15:8 GP_PULL GPIO pullup resistor [7:0] 1: Enabled 0: Disabled 7:0 GP_DATA GPIO data value [7:0] 1: VDD 0: GND Notes: GPIO[7] also used as BOOT mode select after reset GPIO[6:4] also used as PLL mode select after reset. DS639F2 73 CS5378 20.2.3 FILTCFG : 0x20 Figure 45. Filter Configuration Register FILTCFG (MSB) 23 -R/W 0 22 -R/W 0 21 -R/W 0 20 EXP4 R/W 0 19 EXP3 R/W 0 18 EXP2 R/W 0 17 EXP1 R/W 0 16 EXP0 R/W 0 DF Address: 0x20 -R W R/W 15 -R/W 0 14 ORCAL R/W 0 13 USEOR R/W 0 12 USEGR R/W 0 11 -R/W 0 10 FSEL2 R/W 0 9 FSEL1 R/W 0 8 FSEL0 R/W 0 Not defined; read as 0 Readable Writable Readable and Writable 7 DEC3 R/W 0 6 DEC2 R/W 0 5 DEC1 R/W 0 4 DEC0 R/W 0 3 -R/W 0 2 -R/W 0 1 -R/W 0 (LSB) 0 -R/W 0 Bits in bottom rows are reset condition Bit definitions: 23:21 -reserved 15 14 -ORCAL reserved Run OFFSET calibration 1: Enable 0: Disable 7:4 DEC[3:0] Decimation selection (Output word rate) 0111: 0110: 0101: 0100: 0011: 0010: 0001: 0000: 1111: 1110: 1101: 1100: 1011: 1010: 1001: 1000: 3:0 -4000 SPS 2000 SPS 1000 SPS 500 SPS 333 SPS 250 SPS 200 SPS 125 SPS 100 SPS 50 SPS 40 SPS 25 SPS 20 SPS 10 SPS 5 SPS 1 SPS 20:16 EXP[4:0] OFFSET calibration exponent 13 USEOR Use OFFSET correction 1: Enable 0: Disable 12 USEGR Use GAIN correction 1: Enable 0: Disable 11 10:8 -- reserved reserved FSEL[2:0] Output filter stage select 111: reserved 110: reserved 101: IIR 3rd Order 100: IIR 2nd Order 011: IIR 1st Order 010: FIR2 Output 001: FIR1 Output 000: SINC Output DS639F2 74 CS5378 20.2.4 GAIN : 0x21 Figure 46. Gain Correction Register GAIN (MSB) 23 GAIN23 R/W 0 22 GAIN22 R/W 0 21 GAIN21 R/W 0 20 GAIN20 R/W 0 19 GAIN19 R/W 0 18 GAIN18 R/W 0 17 GAIN17 R/W 0 16 GAIN16 R/W 0 DF Address: 0x21 -R W R/W 15 GAIN15 R/W 0 14 GAIN14 R/W 0 13 GAIN13 R/W 0 12 GAIN12 R/W 0 11 GAIN11 R/W 0 10 GAIN10 R/W 0 9 GAIN9 R/W 0 8 GAIN8 R/W 0 Not defined; read as 0 Readable Writable Readable and Writable 7 GAIN7 R/W 0 6 GAIN6 R/W 0 5 GAIN5 R/W 0 4 GAIN4 R/W 0 3 GAIN3 R/W 0 2 GAIN2 R/W 0 1 GAIN1 R/W 0 (LSB) 0 GAIN0 R/W 0 Bits in bottom rows are reset condition Bit definitions: 23:16 GAIN[23:16] Gain Correction Upper Byte 15:8 GAIN[15:8] Gain Correction Middle Byte 15:8 GAIN[7:0] Gain Correction Lower Byte DS639F2 75 CS5378 20.2.5 OFFSET : 0x25 Figure 47. Offset Correction Register OFFSET (MSB) 23 OFST23 R/W 0 22 OFST22 R/W 0 21 OFST21 R/W 0 20 OFST20 R/W 0 19 OFST19 R/W 0 18 OFST18 R/W 0 17 OFST17 R/W 0 16 OFST16 R/W 0 DF Address: 0x25 -R W R/W 15 OFST15 R/W 0 14 OFST14 R/W 0 13 OFST13 R/W 0 12 OFST12 R/W 0 11 OFST11 R/W 0 10 OFST10 R/W 0 9 OFST9 R/W 0 8 OFST8 R/W 0 Not defined; read as 0 Readable Writable Readable and Writable 7 OFST7 R/W 0 6 OFST6 R/W 0 5 OFST5 R/W 0 4 OFST4 R/W 0 3 OFST3 R/W 0 2 OFST2 R/W 0 1 OFST1 R/W 0 (LSB) 0 OFST0 R/W 0 Bits in bottom rows are reset condition Bit definitions: 23:16 OFST[23:16] Offset Correction Upper Byte 15:8 OFST[15:8] Offset Correction Middle Byte 15:8 OFST[7:0] Offset Correction Lower Byte DS639F2 76 CS5378 20.2.6 TIMEBRK : 0x29 Figure 48. Time Break Counter Register TIMEBRK (MSB) 23 TBRK23 R/W 0 22 TBRK22 R/W 0 21 TBRK21 R/W 0 20 TBRK20 R/W 0 19 TBRK19 R/W 0 18 TBRK18 R/W 0 17 TBRK17 R/W 0 16 TBRK16 R/W 0 DF Address: 0x29 -R W R/W 15 TBRK15 R/W 0 14 TBRK14 R/W 0 13 TBRK13 R/W 0 12 TBRK12 R/W 0 11 TBRK11 R/W 0 10 TBRK10 R/W 0 9 TBRK9 R/W 0 8 TBRK8 R/W 0 Not defined; read as 0 Readable Writable Readable and Writable 7 TBRK7 R/W 0 6 TBRK6 R/W 0 5 TBRK5 R/W 0 4 TBRK4 R/W 0 3 TBRK3 R/W 0 2 TBRK2 R/W 0 1 TBRK1 R/W 0 (LSB) 0 TBRK0 R/W 0 Bits in bottom rows are reset condition Bit definitions: 23:16 TBRK[23:16] Time Break Counter 15:8 Upper Byte TBRK[15:8] Time Break Counter 15:8 Middle Byte TBRK[7:0] Time Break Counter Lower Byte DS639F2 77 CS5378 20.2.7 TBSCFG : 0x2A Figure 49. Test Bit Stream Configuration Register TBSCFG (MSB) 23 INTP7 R/W 0 22 INTP6 R/W 0 21 INTP5 R/W 0 20 INTP4 R/W 0 19 INTP3 R/W 0 18 INTP2 R/W 0 17 INTP1 R/W 0 16 INTP0 R/W 0 DF Address: 0x2A -R W R/W 15 -R/W 0 14 RATE2 R/W 0 13 RATE1 R/W 0 12 RATE0 R/W 0 11 TSYNC R/W 0 10 -R/W 0 9 -R/W 0 8 -R/W 0 Not defined; read as 0 Readable Writable Readable and Writable 7 LOOP R/W 0 6 RUN R/W 0 5 DDLY5 R/W 0 4 DDLY4 R/W 0 3 DDLY3 R/W 0 2 DDLY2 R/W 0 1 DDLY1 R/W 0 (LSB) 0 DDLY0 R/W 0 Bits in bottom rows are reset condition Bit definitions: 23:16 INTP[7:0] Interpolation factor 0xFF: 256 0xFE: 255 ... 0x01: 2 0x00: 1 (use once) 15 -reserved 7 LOOP Loopback TBSDATA output to MDATA inputs 1: Enabled 0: Disabled Run Test Bit Stream 1: Enabled 0: Disabled 14:12 RATE[2:0] TBSDATA and TBSCLK output rate. 111: 2.048 MHz 110: 1.024 MHz 101: 512 kHz 100: 256 kHz 011: 128 kHz 010: 64 kHz 001: 32 kHz 000: 4 kHz Synchronization 1: Sync enabled 0: No sync 6 RUN 11 TSYNC 5:0 DDLY[5:0] TBSDATA output delay 0x3F: 63 bits 0x3E: 62 bits ... 0x01: 1 bit 0x00: 0 bits ( no delay) 10:8 -- reserved DS639F2 78 CS5378 20.2.8 TBSGAIN : 0x2B Figure 50. Test Bit Stream Gain Register TBSGAIN (MSB) 23 TGAIN23 R/W 0 22 TGAIN22 R/W 0 21 TGAIN21 R/W 0 20 TGAIN20 R/W 0 19 TGAIN19 R/W 0 18 TGAIN18 R/W 0 17 TGAIN17 R/W 0 16 TGAIN16 R/W 0 DF Address: 0x2B -R W R/W 15 TGAIN15 R/W 0 14 TGAIN14 R/W 0 13 TGAIN13 R/W 0 12 TGAIN12 R/W 0 11 TGAIN11 R/W 0 10 TGAIN10 R/W 0 9 TGAIN9 R/W 0 8 TGAIN8 R/W 0 Not defined; read as 0 Readable Writable Readable and Writable 7 TGAIN7 R/W 0 6 TGAIN6 R/W 0 5 TGAIN5 R/W 0 4 TGAIN4 R/W 0 3 TGAIN3 R/W 0 2 TGAIN2 R/W 0 1 TGAIN1 R/W 0 (LSB) 0 TGAIN0 R/W 0 Bits in bottom rows are reset condition Bit definitions: 23:16 TGAIN[23:16] Test Bit Stream Gain 15:8 Upper Byte TGAIN[15:8] Test Bit Stream Gain Middle Byte 15:8 TGAIN[7:0] Test Bit Stream Gain Lower Byte DS639F2 79 CS5378 20.2.9 SYSTEM1, SYSTEM2 : 0x2C, 0x2D Figure 51. User Defined System Register SYSTEM1 (MSB) 23 SYS23 R/W 0 22 SYS22 R/W 0 21 SYS21 R/W 0 20 SYS20 R/W 0 19 SYS19 R/W 0 18 SYS18 R/W 0 17 SYS17 R/W 0 16 SYS16 R/W 0 DF Address: 0x2C -R W R/W 15 SYS15 R/W 0 14 SYS14 R/W 0 13 SYS13 R/W 0 12 SYS12 R/W 0 11 SYS11 R/W 0 10 SYS10 R/W 0 9 SYS9 R/W 0 8 SYS8 R/W 0 Not defined; read as 0 Readable Writable Readable and Writable 7 SYS7 R/W 0 6 SYS6 R/W 0 5 SYS5 R/W 0 4 SYS4 R/W 0 3 SYS3 R/W 0 2 SYS2 R/W 0 1 SYS1 R/W 0 (LSB) 0 SYS0 R/W 0 Bits in bottom rows are reset condition Bit definitions: 23:16 SYS[23:16] System Register Upper Byte 15:8 SYS[15:8] System Register Middle Byte 15:8 SYS[7:0] System Register Lower Byte DS639F2 80 CS5378 20.2.10 VERSION : 0x2E Figure 52. Hardware Version ID Register VERSION (MSB) 23 TYPE7 R/W 0 22 TYPE6 R/W 1 21 TYPE5 R/W 1 20 TYPE4 R/W 1 19 TYPE3 R/W 1 18 TYPE2 R/W 0 17 TYPE1 R/W 0 16 TYPE0 R/W 0 DF Address: 0x2E -R W R/W 15 HW7 R/W 0 14 HW6 R/W 0 13 HW5 R/W 0 12 HW4 R/W 0 11 HW3 R/W 0 10 HW2 R/W 0 9 HW1 R/W 1 8 HW0 R/W 0 Not defined; read as 0 Readable Writable Readable and Writable 7 ROM7 R/W 0 6 ROM6 R/W 0 5 ROM5 R/W 0 4 ROM4 R/W 0 3 ROM3 R/W 0 2 ROM2 R/W 0 1 ROM1 R/W 1 (LSB) 0 ROM0 R/W 0 Bits in bottom rows are reset condition Bit definitions: 23:16 TYPE [7:0] Chip Type 78 - CS5378 15:8 HW [7:0] Hardware Revision 01 - CS5378 Rev A 02 - CS5378 Rev B 7:4 ROM [7:0] ROM Version 01 - Ver 1.0 02 - Ver 2.0 DS639F2 81 CS5378 20.2.11 SELFTEST : 0x2F Figure 53. Self Test Result Register SELFTEST (MSB) 23 -R/W 0 22 -R/W 0 21 -R/W 0 20 -R/W 0 19 EU3 R/W 1 18 EU2 R/W 0 17 EU1 R/W 1 16 EU0 R/W 0 DF Address: 0x2F -R W R/W 15 DRAM3 R/W 1 14 DRAM2 R/W 0 13 DRAM1 R/W 1 12 DRAM0 R/W 0 11 PRAM3 R/W 1 10 PRAM2 R/W 0 9 PRAM1 R/W 1 8 PRAM0 R/W 0 Not defined; read as 0 Readable Writable Readable and Writable 7 DROM3 R/W 1 6 DROM2 R/W 0 5 DROM1 R/W 1 4 DROM0 R/W 0 3 PROM3 R/W 1 2 PROM2 R/W 0 1 PROM1 R/W 1 (LSB) 0 PROM0 R/W 0 Bits in bottom rows are reset condition Bit definitions: 23:20 -reserved 15:12 DRAM [3:0] Data RAM Test ‘A’: Pass ‘F’: Fail Program RAM Test ‘A’: Pass ‘F’: Fail 7:4 DROM [3:0] Data ROM Test ‘A’: Pass ‘F’: Fail Program ROM Test ‘A’: Pass ‘F’: Fail 19:16 EU [3:0] Execution Unit Test ‘A’: Pass ‘F’: Fail 11:8 PRAM [3:0] 3:0 PROM [3:0] DS639F2 82 CS5378 21. PIN DESCRIPTION GPIO0 GPIO1 GPIO2 GPIO3 GPIO4:PLL0 GPIO5:PLL1 GPIO6:PLL2 TBSDATA VDDPAD GNDPAD MCLK MSYNC MDATA MFLAG 1 2 3 4 5 6 7 8 9 10 11 12 13 14 28 27 26 25 24 23 22 21 20 19 18 17 16 15 GPIO7:BOOT SS:EECS MOSI MISO SCK DRDY GNDCORE VDDCORE TIMEB SYNC RESET CLK GNDPLL VDDPLL Figure 54. CS5378 Pin Assignments Pin Name GPIO[0:3] GPIO[4:6]:PLL[0:2] Pin Number 1, 2, 3, 4 5, 6, 7 Pin Type General Purpose Input / Output Input / Output Input / Output Pin Description General Purpose I/O. General Purpose I/O with PLL mode select. GPIO pins have weak (~100 kΩ) internal pull-ups. PLL mode selection latched immediately after reset. PLL[2:0] 111 110 101 100 011 010 001 000 Reset Mode 32.768 MHz clock input (PLL bypass). 1.024 MHz clock input. 2.048 MHz clock input. 4.096 MHz clock input. 32.768 MHz clock input (PLL bypass). 1.024 MHz Manchester input. 2.048 MHz Manchester input. 4.096 MHz Manchester input. GPIO7:BOOT 28 Input / Output General Purpose I/O with boot mode select. GPIO pins have weak (~100 kΩ) internal pull-ups. Boot mode selection latched immediately after reset. BOOT 1 0 Reset Mode EEPROM boot Microcontroller boot DS639F2 83 CS5378 Pin Name TBSDATA MCLK MSYNC MDATA MFLAG CLK RESET SYNC TIMEB DRDY SCK MISO MOSI SS:EECS VDDPAD, GNDPAD VDDPLL, GNDPLL VDDCORE, GNDCORE Pin Number 8 11 12 13 14 17 18 19 20 23 24 25 26 27 9, 10 15, 16 21, 22 Pin Type Test Bit Stream Output Modulator Interface Output Output Input Input Telemetry Interface Input Input Input Input Serial Interface Output Input / Output Input / Output Input / Output Input Supply Supply Supply Power Supplies Pin Description Test bit stream data output. Modulator clock output. Modulator sync output. Modulator data input. Modulator flag input. Clock input. Reset, active low. Sync input. Time break input. Data ready, active low. Serial clock. Serial data, master in / slave out. Serial data, master out / slave in. Slave select with EEPROM chip select, active low. Pin power supply. PLL power supply. Logic core power supply. DS639F2 84 CS5378 22.PACKAGE DIMENSIONS 28L SSOP PACKAGE DRAWING N D E11 A2 A1 A E ∝ L e b2 SIDE VIEW END VIEW SEATING PLANE 123 TOP VIEW DIM A A1 A2 b D E E1 e L ∝ MIN -0.002 0.064 0.009 0.390 0.291 0.197 0.022 0.025 0° INCHES NOM -0.006 0.069 -0.4015 0.307 0.209 0.026 0.0354 4° MAX 0.084 0.010 0.074 0.015 0.413 0.323 0.220 0.030 0.041 8° MIN -0.05 1.62 0.22 9.90 7.40 5.00 0.55 0.63 0° MILLIMETERS NOM -0.15 1.75 -10.20 7.80 5.30 0.65 0.90 4° NOTE MAX 2.13 0.25 1.88 0.38 10.50 8.20 5.60 0.75 1.03 8° 2,3 1 1 JEDEC #: MO-150 Controlling Dimension is Millimeters DS639F2 85 CS5378 23.ORDERING INFORMATION Model Temperature Package CS5378-IS -40 to +85 °C CS5378-ISZ Lead Free 28-pin SSOP 24.ENVIRONMENTAL, MANUFACTURING, & HANDLING INFORMATION Model Number Peak Reflow Temp 240 °C 260 °C MSL Rating* 2 3 Max Floor Life 365 Days 7 Days CS5378-IS CS5378-ISZ Lead Free * MSL (Moisture Sensitivity Level) as specified by IPC/JEDEC J-STD-020. DS639F2 86 CS5378 25.REVISION HISTORY Revision Date Changes PP1 F1 F2 FEB 2004 OCT 2005 SEP 2008 Initial “Preliminary Product” release. Added lead-free device ordering information. Added MSL data. Rev B. Update Single-S part numbers. Remove TBS impulse mode. DS639F2 87 CS5378 Contacting Cirrus Logic Support For all product questions and inquiries contact a Cirrus Logic Sales Representative. To find the one nearest to you go to www.cirrus.com IMPORTANT NOTICE Cirrus Logic, Inc. and its subsidiaries ("Cirrus") believe that the information contained in this document is accurate and reliable. However, the information is subject to change without notice and is provided "AS IS" without warranty of any kind (express or implied). Customers are advised to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgment, including those pertaining to warranty, indemnification, and limitation of liability. No responsibility is assumed by Cirrus for the use of this information, including use of this information as the basis for manufacture or sale of any items, or for infringement of patents or other rights of third parties. This document is the property of Cirrus and by furnishing this information, Cirrus grants no license, express or implied under any patents, mask work rights, copyrights, trademarks, trade secrets or other intellectual property rights. Cirrus owns the copyrights associated with the information contained herein and gives consent for copies to be made of the information only for use within your organization with respect to Cirrus integrated circuits or other products of Cirrus. This consent does not extend to other copying such as copying for general distribution, advertising or promotional purposes, or for creating any work for resale. CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE ("CRITICAL APPLICATIONS"). CIRRUS PRODUCTS ARE NOT DESIGNED, AUTHORIZED OR WARRANTED FOR USE IN PRODUCTS SURGICALLY IMPLANTED INTO THE BODY, AUTOMOTIVE SAFETY OR SECURITY DEVICES, LIFE SUPPORT PRODUCTS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF CIRRUS PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER'S RISK AND CIRRUS DISCLAIMS AND MAKES NO WARRANTY, EXPRESS, STATUTORY OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE, WITH REGARD TO ANY CIRRUS PRODUCT THAT IS USED IN SUCH A MANNER. IF THE CUSTOMER OR CUSTOMER'S CUSTOMER USES OR PERMITS THE USE OF CIRRUS PRODUCTS IN CRITICAL APPLICATIONS, CUSTOMER AGREES, BY SUCH USE, TO FULLY INDEMNIFY CIRRUS, ITS OFFICERS, DIRECTORS, EMPLOYEES, DISTRIBUTORS AND OTHER AGENTS FROM ANY AND ALL LIABILITY, INCLUDING ATTORNEYS' FEES AND COSTS, THAT MAY RESULT FROM OR ARISE IN CONNECTION WITH THESE USES. Cirrus Logic, Cirrus, and the Cirrus Logic logo designs are trademarks of Cirrus Logic, Inc. All other brand and product names in this document may be trademarks or service marks of their respective owners. SPI is a trademark of Motorola, Inc. DS639F2 88