TLF50211ELXUMA1

TLF50211ELV50 2.2 MHz Step-Down Regulator 500 mA, 5 V, lo w qui escent current 1 Overview Features • 500 mA step down voltage regulator • 5 V Output voltage • ±2% output voltage tolerance • Low quiescent current (less than 45 µA at nominal battery voltage) • Integrated power transistor • Current mode PWM regulation • PFM mode for light load current • Input voltage range from 4.75 V to 45 V • 2.2 MHz switching frequency • 100% Duty cycle • Synchronization input • Very low shutdown current consumption (< 2 µA) • Soft-start function • Input undervoltage lockout • Suited for automotive applications: Tj = -40°C to 150°C • Green Product (RoHS compliant) Potential applications • Applications with a 5.0 V switching regulator as replacement for linear voltage regulator with low quiescent current, such as: – dashboard – engine management – braking – body – infotainment Product validation Qualified for automotive applications. Product Validation according to AEC-Q100/101. Data Sheet www.infineon.com 1 Rev. 1.1 2018-03-07 TLF50211ELV50 2.2 MHz Step-Down Regulator 500 mA, 5 V, low quiescent current Overview Description The TLF50211EL is a high frequency PWM step-down DC/DC converter with an integrated PMOS power switch, packaged in a small PG-SSOP-14 with exposed pad. The wide input voltage range from 4.75 V to 45 V makes the TLF50211EL suitable for a wide variety of applications. The device is designed to be used under harsh automotive environmental conditions. The switching frequency of nominal 2.2 MHz allows the use of small and cost-effective inductors and capacitors, resulting in a low, predictable output voltage ripple and in minimized consumption of board space. In light load condition the device operates in Pulse Frequency Modulation (PFM) to optimize the efficiency. Between the single pulses, all internal controlling circuitry is switched off to reduce the internal power consumption. The TLF50211EL includes protection features such as a cycle-by-cycle current limitation, overtemperature shutdown and input undervoltage lockout. The enable function, in shutdown mode with less than 2 µA current consumption, enables easy power management in battery-powered systems. The voltage regulation loop provides an excellent line and load regulation, the stability of the loop is ensured by an internal compensation network. This compensation network combined with a current mode regulation control guarantees a highly effective line transient rejection. During start-up the integrated soft-start limits the inrush current peak and prevents output voltage overshoot. Type Package Marking TLF50211EL PG-SSOP-14 TLF50211 Data Sheet 2 Rev. 1.1 2018-03-07 TLF50211ELV50 2.2 MHz Step-Down Regulator 500 mA, 5 V, low quiescent current Table of contents 1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Potential applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Product validation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Table of contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3 3.1 3.2 Pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Pin assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Pin definitions and functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 4 4.1 4.2 4.3 General product characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Functional range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Thermal resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 5.1 5.1.1 5.1.2 5.1.3 5.2 5.3 Buck regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Regulator loop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 PWM (Pulse Width Modulation) mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 PFM (Pulse Frequency Modulation) mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Electrical characteristics buck regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Performance graphs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 6 6.1 6.2 Enable and thermal shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Electrical characteristics Enable, bias and thermal shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 7 7.1 7.2 Oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Electrical characteristics buck regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 8 8.1 8.2 Application information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 General layout recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Further application information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 9 Package outlines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 10 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Data Sheet 3 7 7 8 8 Rev. 1.1 2018-03-07 TLF50211ELV50 2.2 MHz Step-Down Regulator 500 mA, 5 V, low quiescent current Block diagram 2 Block diagram VS 13 TLF50211EL Over Temperature Shutdown EN Enable 14 Buck Converter FREQ 5 SYNC 4 11 SWO Oscillator INT. SUPPLY Bandgap Reference 7 FB Soft Start Ramp Generator Figure 1 Data Sheet N.C. 3 6 N.C. N.C. 2 1 N.C. 8 9 10 12 N.C. GND GND N.C. Block diagram 4 Rev. 1.1 2018-03-07 TLF50211ELV50 2.2 MHz Step-Down Regulator 500 mA, 5 V, low quiescent current Pin configuration 3 Pin configuration 3.1 Pin assignment N.C. 1 N.C. TLF50211EL 14 EN 2 13 VS N.C. 3 12 N.C. SYNC 4 11 SWO FREQ 5 10 GND N.C. 6 9 GND FB 7 8 N.C. PG-SSOP14 Figure 2 Pin configuration 3.2 Pin definitions and functions Pin Symbol Function 1 N.C. Not Connected Internally not connected. Leave open or connect to GND. 2 N.C. Not Connected Internally not connected. Leave open or connect to GND. 3 N.C. Not Connected Internally not connected. Leave open or connect to GND. 4 SYNC Synchronization input Connect to an external clock signal in order to synchronize/adjust the switching frequency. This feature is not functionally in PFM mode. 5 FREQ Frequency adjustment pin Connect an external resistor to GND to adjust the switching frequency, do not leave open. In case the synchronization option is used, the resistor must be dimensioned close to the desired synchronization frequency. 6 N.C. Not Connected Internally not connected. Leave open or connect to GND. 7 FB Feedback input Connect this pin directly to the output capacitor. Also input for internal power supply. The internal power supply is taken from the output voltage. 8 N.C. Not Connected Internally not connected. Leave open or connect to GND. Data Sheet 5 Rev. 1.1 2018-03-07 TLF50211ELV50 2.2 MHz Step-Down Regulator 500 mA, 5 V, low quiescent current Pin configuration Pin Symbol Function 9 GND Ground Connect this pin directly with low inductive and broad trace to ground, do not leave open. 10 GND Ground Connect this pin directly with low inductive and broad trace to ground, do not leave open. 11 SWO Buck Switch Output Drain of the integrated power-PMOS transistor. Connect directly to the cathode of the catch diode and the buck circuit inductance. 12 N.C. Not Connected Internally not connected. Leave open or connect to GND. 13 VS Supply Voltage input Connect to supply voltage source. 14 EN Enable input Switch to high level to enable the device, switch to low level to disable the device. Exposed pad Connect to heatsink area and GND by low inductance wiring. Data Sheet 6 Rev. 1.1 2018-03-07 TLF50211ELV50 2.2 MHz Step-Down Regulator 500 mA, 5 V, low quiescent current General product characteristics 4 General product characteristics 4.1 Absolute maximum ratings Table 1 Absolute maximum ratings1) Tj = -40°C to 150°C; all voltages with respect to ground (unless otherwise specified) Parameter Symbol Values Min. Typ. Max. Unit Note or Number Test Condition Voltages Enable input VEN -40 – 45 V – P_4.1.1 Synchronization input VSYNC -0.3 – 5.5 V – P_4.1.2 6.2 V t < 10 s 2) P_4.1.3 5.5 V – P_4.1.4 Feedback Input Frequency adjustment pin VFB -0.3 – VFREQ -0.3 – 6.2 V t < 10 s 5.5 V – 6.2 V 2) P_4.1.5 P_4.1.6 t < 10 s 2) P_4.1.7 Buck switch output VSWO -2.0 – VVS + 0.3 V – P_4.1.8 Supply voltage input VVS -0.3 – 45 V – P_4.1.9 Junction temperature Tj -40 – 150 °C – P_4.1.10 Storage temperature Tstg -55 – 150 °C – P_4.1.11 VESD -2 – 2 kV HBM Temperatures ESD susceptibility ESD resistivity P_4.1.12 3) P_4.1.13 P_4.1.14 ESD resistivity to GND VESD -500 – 500 V CDM ESD resistivity corner pins to GND VESD -750 – 750 V CDM 3) 1) Not subject to production test, specified by design 2) ESD susceptibility HBM according to ANSI/ESDA/JEDEC JS-001. 3) ESD susceptibility, Charged Device Model “CDM” EIA/JESD22-C101 or ESDA STM5.3.1 Notes 1. Stresses above the ones listed here may cause permanent damage to the device. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. 2. Integrated protection functions are designed to prevent IC destruction under fault conditions described in the data sheet. Fault conditions are considered as “outside” normal operating range. Protection functions are not designed for continuous repetitive operation. Data Sheet 7 Rev. 1.1 2018-03-07 TLF50211ELV50 2.2 MHz Step-Down Regulator 500 mA, 5 V, low quiescent current General product characteristics 4.2 Functional range Table 2 Functional range Parameter Symbol Values Number Min. Unit Note or Test Condition Typ. Max. Supply voltage VS 4.75 – 45 V – P_4.2.1 Buck inductor LBU 3.3 – 22 µH – P_4.2.2 Buck capacitor CBU1 10 – 50 µF – Buck capacitor ESR ESRBU1 0.015 – 0.100 Ω – Junction temperature Tj -40 150 – – °C P_4.2.3 1) P_4.2.4 P_4.2.5 1) See section “Application information” on Page 22 for loop compensation requirements and refer to Application Note for dimensioning the output filter. Note: Within the functional range the IC operates as described in the circuit description. The electrical characteristics are specified within the conditions given in the related electrical characteristics table. 4.3 Thermal resistance Table 3 Thermal resistance Parameter Junction to case1) Junction to ambient 2) Symbol Values Unit Note or Number Test Condition Min. Typ. Max. RthJC – 10 – K/W – P_4.3.1 RthJA – 47 – K/W 2s2p P_4.3.2 RthJA – 54 – K/W 1s0p + 600 mm2 P_4.3.3 RthJA – 64 – K/W 1s0p + 300 mm2 P_4.3.4 1) Not subject to production test, specified by design. 2) Specified RthJA value is according to JEDEC 2s2p (JESD 51-7) + (JESD 51-5) and JEDEC 1s0p (JESD 51-3) + heatsink area at natural convection on FR4 board. Data Sheet 8 Rev. 1.1 2018-03-07 TLF50211ELV50 2.2 MHz Step-Down Regulator 500 mA, 5 V, low quiescent current Buck regulator 5 Buck regulator 5.1 Description The TLF50211EL is a monolithic current mode step down converter with adjustable switching frequency fOSC. It is capable to operate either in Pulse Width Modulation (PWM) or in Pulse Frequency Modulation (PFM) Mode. 5.1.1 Regulator loop Power stage The supply voltage is connected to pin VS. Between pin VS and pin SWO there is an internal shunt resistor and the internal PMOS power stage. The PMOS is driven by the driver stage. Regulator block The feedback signal VFB is connected to pin FB. Between pin FB and pin GND is an internal resistor divider. An error amplifier and a comparator are connected to this resistor divider: The error amplifier EA-gmV, which is controlling the output voltage in PWM mode, and the PFM comparator, which will switch the TLF50281EL into PFM mode and trigger the pulses. The error amplifier EA-gmV is connected to the PWM comparator. The regulation loop operates in current mode: The output current of EA-gmV is subtracted from the sum of the current loop CS-gmI and the slope compensation ISLOPE. The result is evaluated by PWM Comp (a current comparator). The output of PWM Comp defines duty cycle (pulse-width-modulated signal) in PWM mode. The Slope Compensation added to the signal from the error amplifier EA-gmV to the PWM Comparator ensures that no sub harmonics will occur on the input current. The PWM comparator output and the PFM comparator output are connected to the PWM /PFM logic. An external resistor at pin FREQ is required to set the switching frequency (for details please refer to chapter 8 Module Oscillator). The TLF50211EL may also be synchronized to an external frequency. In this case an external clock signal should be connected to pin SYNC. The frequency setting resistor at pin FREQ is still necessary, it has to be selected according to the desired synchronization frequency (for details please refer to Chapter 7 Oscillator . The TLF50211EL can only be synchronized to an external frequency source in PWM mode, this function does not work in PFM mode. The clock manager is clocking the PWM/PFM logic. The PWM/PFM logic is triggering the driver to apply pulses to the internal PMOS power stage. Safety features The shunt resistor in line with the internal PMOS power stage (between pin VS and the power stage) is connected to a current sense amplifier CS-gml. It detects the voltage above the shunt resistor. The amplifier creates a signal which shuts the pulse down in case that the shunt voltage exceeds the reference limit. The current limitation acts as a cycle-by-cycle limitation. Cycle-by-cycle limitation means, that every pulse is switched off as soon as the current through the PMOS exceeds the buck peak over current limit IBUOC. The next pulse starts and will also be switched off as soon as the current limit is exceeded again. This results in a lowered output voltage whilst the output current is limited to a certain value. Input undervoltage shutdown: If the input voltage is below the input undervoltage shutdown threshold VS,off the device will shut down. Output overvoltage protection: If the output voltage exceeds the PFM threshold the device will switch from PWM to PFM. Pulses will then be generated only depending on the value of the output voltage VCC. Data Sheet 9 Rev. 1.1 2018-03-07 TLF50211ELV50 2.2 MHz Step-Down Regulator 500 mA, 5 V, low quiescent current Buck regulator Soft start function: An integrated soft start function of duration tstart ensures, that the inrush current will be limited. After an overtemperature shutdown the regulator always restarts with a soft start. Overtemperature shutdown: An internal temperature sensor detects the temperature of the device. It will be switched off if the junction temperature exceeds the overtemperature shutdown threshold Tj,sd and restart with a certain hysteresis Tj,sd_hyst (for details please refer to Chapter 6 Enable and thermal shutdown ). Biasing The internal biasing is taken from pin VS as well as from pin FB (connected to VCC) (for details please refer to Chapter 6 Enable and thermal shutdown ). Thus the power consumption from the supply voltage VS can be minimized. VS + VBG CS-gmI PFM Comparator + FB - GateD + - PWM Comp EA-gmV PWM PFM Logic Driver SWO SYNC_IN FREQ Clock Manager CK_A SoftStart Slope Comp. CLK GND Figure 3 Block diagram buck regulator 5.1.2 PWM (Pulse Width Modulation) mode Under normal conditions the TLF50211EL will operate with a constant switching frequency fOSC in PWM mode. The ratio between switch-on-time TON and switch-off-time TOFF is mainly determined by the ratio between the input voltage VS and the output voltage VCC and is influenced by the output current ICC. In PWM mode the device may operate with 100% duty cycle, in this case the internal PMOS is constantly conducting current. The current limitation feature is operating under this condition. If the switch-on-time TON should theoretically be below the minimum threshold TON,min (due to low load or due to the ratio between input voltage VS and output voltage VCC depending on the switching frequency), it will be reduced to the minimum value switch-on-time TON,min and stay there. As a consequence the output voltage VCC will increase. The PFM comparator detects the PFM threshold and will then switch the device into PFM mode. There is no possibility to disable the PFM function. Data Sheet 10 Rev. 1.1 2018-03-07 TLF50211ELV50 2.2 MHz Step-Down Regulator 500 mA, 5 V, low quiescent current Buck regulator 5.1.3 PFM (Pulse Frequency Modulation) mode To optimize the efficiency and to reduce the current consumption, the TLF50211EL automatically switches to PFM mode under low load conditions. In PFM mode the internal power stage including the driver stage is switched off and will only be switched on for applying pulses to charge the output capacitor. The pulses will be created by monitoring the voltage of the output filter capacitor COUT. Thus in PFM mode the repetition time of pulses depend on the output current and/or the ratio between input voltage VS and output voltage VCC. Transition from PWM to PFM Figure 4 shows the transition from Pulse Width Modulation to Pulse Frequency Modulation under the assumption, that the input voltage VS will be constant and only the output current ICC will vary. The diagram shows the principle, in reality the signals might look slightly different. The diagram is without scale in respect of time, voltage and current values. Starting from left of the figure a certain output current, here named i1, is applied to the regulator output. This results in a duty cycle D1 with the on-time TON1 of the internal power stage. The switching frequency fOSC is constant as set by the frequency setting resistor RFREQ. The regulator is in PWM mode, the output voltage is VREF_PWM which is equal to VFB in PWM mode. At point t1 the output current decreases from i1 to a lower i2. This results in a duty cycle D2 with the on-time TON2 of the internal power stage. Due to the reduced output load the on-time TON2 is shorter (the regulator is in Discontinuous Conduction Mode DCM) than TON1. The switching frequency fOSC is constant as set by the frequency setting resistor RFREQ. The regulator is still in PWM mode, the output voltage is VREF_PWM which is equal to VFB in PWM mode. In Continuous Conduction Mode CCM the variation from TON1 to TON2 will be very small due to smaller conduction losses. At point t2 the output current decreases again from i2 to a lower i3. As a consequence the on-time TON will be reduced also. The output current i3 is so low, that the on-time TON3 would be smaller than the TON,min. The regulator does not allow a on-time smaller than TON,min. Therefore we can say that the output current i3 is under the imaginary current threshold for transition from PWM to PFM iPWM/PFM. With the pulse staying at ontime TON,min the output voltage VCC will rise. The regulator is still in PWM mode, but the output voltage rises. At point t3 after a normal time period TPWM as adjusted by the frequency setting resistor RFREQ, a further pulse of the duration TON,min is applied, the output voltage VCC keeps on rising. The regulator is still in PWM mode. At point t4 the output voltage VCC touches (or exceeds) the voltage threshold for transition from PWM to PFM VPWM/PFM. The regulator is now switching internally from PWM to PFM. In PFM mode the power consumption of the internal blocks is reduced. The reference for the output voltage VCC is switched from VREF_PWM (which is equal to VFB in PWM mode) to VREF_PFM (which is equal to VFB in PFM mode). The reference for VFB in PFM mode is higher than the reference in PWM mode to avoid voltage dumps at the output voltage VCC due to sudden load steps and to give the regulator more reaction time to switch back to PWM mode. The regulator is now in PFM mode, the output voltage is VREF_PFM which is equal to VFB (or slightly higher) in PFM mode. The output voltage VCC is monitored and as soon as it touches the PFM reference voltage VREF_PFM a pulse of the on-time TON,min is triggered. The time between two pulses is depending on the discharging of the output capacitor COUT. Data Sheet 11 Rev. 1.1 2018-03-07 TLF50211ELV50 2.2 MHz Step-Down Regulator 500 mA, 5 V, low quiescent current Output current Buck regulator i1 i2 iPWM/PFM i3 Switching signal time D1 D2 D3 TON2 TON1 TON,min time TPWM Output voltage TPWM TPWM Switch to PFM mode VPWM/PFM VREF_PFM VREF_PWM time t1 Figure 4 t2 t3 t4 PWM to PFM transition (timing diagram) Transition from PFM to PWM Figure 5 shows the transition from Pulse Frequency Modulation to Pulse Width Modulation under the assumption, that the input voltage VS will be constant, and only the output current ICC will vary. The diagram shows the principle, in reality the signals might look slightly different. The diagram is without scale in respect of time, voltage and current values. Starting from left of the figure a certain output current, here named i3, is applied to the regulator output. i3 shall be below the imaginary current threshold for transition from PFM to PWM iPFM/PWM. The regulator is in PFM mode, the output voltage is VREF_PFM, which is equal to VFB in PFM mode (or slightly higher). Pulses of the duration TON,min are triggered whenever the output voltage VCC touches the PFM reference voltage VREF_PFM. At point t5 the output current increases from i3 to a higher i2, that shall be above the imaginary current threshold for transition from PFM to PWM iPFM/PWM. Due to the higher output current more pulses of the duration TON,min have to be triggered, the frequency of these pulses is monitored. The frequency of these pulses increases until it is higher than the switching frequency fOSC set by the frequency setting resistor RFREQ. The regulator is still in PFM mode. At point t6 the frequency monitoring detects that the frequency of the PFM pulses is being higher than the frequency threshold for transition from PFM to PWM fPFM/PWM. Therefore the regulator switches back to PWM mode. This results in a certain duty cycle D2 with the on-time TON2 of the internal power stage. The time period TPWM is as adjusted by the frequency setting resistor RFREQ. Data Sheet 12 Rev. 1.1 2018-03-07 TLF50211ELV50 2.2 MHz Step-Down Regulator 500 mA, 5 V, low quiescent current Output current Buck regulator i2 iPFM/PWM i3 Switching signal time D2 TON,min TON,min TPWM TON2 Output voltage time Switch to PWM mode VPWM/PFM VREF_PFM VREF_PWM time t5 Figure 5 t6 PFM to PWM transition (timing diagram) Frequency variation during PWM/PFM transition Figure 6 shows the transition from Pulse Frequency Modulation to Pulse Width Modulation (and vice versa) in relation to output current and switching frequency. The diagram shows the principle, in reality the signals might be slightly different. The diagram is without scale in respect of frequency and current values. The transition from PWM to PFM is shown in a grey line. Starting from right the switching frequency fPWM is constant as set by the frequency setting resistor RFREQ. The output current ICC is decreasing. As soon as the output current ICC is below the imaginary current threshold for transition from PWM to PFM iPWM/PFM, the regulator will be switched from PWM to PFM mode depending on the output voltage VCC. With the output current ICC decreasing, the switching frequency will also decrease, as the pulses are triggered by monitoring the output voltage VCCat capacitor COUT. The transition from PFM to PWM is shown in a black line. Starting from left the switching frequency is increasing with the increasing output current ICC. As soon as the switching frequency is crossing the frequency threshold for transition from PFM to PWM fPFM/PWM (which is above the switching frequency fOSC set by the frequency setting resistor RFREQ) the regulator will switch from PFM to PWM. Data Sheet 13 Rev. 1.1 2018-03-07 TLF50211ELV50 2.2 MHz Step-Down Regulator 500 mA, 5 V, low quiescent current Switching Frequency (log.scale) Buck regulator PWM to PFM PFM to PWM fPFM/PWM fPWM iPWM/PFM Figure 6 Data Sheet iPFM/PWM Output Current (log.scale) PWM PFM transitions 14 Rev. 1.1 2018-03-07 TLF50211ELV50 2.2 MHz Step-Down Regulator 500 mA, 5 V, low quiescent current Buck regulator 5.2 Electrical characteristics buck regulator Table 4 Electrical characteristics: buck regulator VS = 6.0 V to 40 V, Tj = -40°C to 150°C, all voltages with respect to ground (unless otherwise specified) Parameter Symbol Values Unit Min. Typ. Max. Output voltage VFB 4.90 5.00 5.10 V Note or Test Condition Number VEN = 5.0 V 7 V < VS < 12 V 100 mA < ICC < 610 mA P_5.2.1 VEN = 5.0 V 10 V < VS < 35 V ICC = 100 µA P_5.2.2 PWM Mode Output voltage VFB 4.90 5.10 5.30 V PFM Mode Power stage on-resistance Ron – Buck peak over current limit IBUOC 0.85 – 1.5 2.3 Ω Tested at 100 mA, VS = 7.0 V P_5.2.8 1.7 A – P_5.2.9 P_5.2.10 Current transition rise/fall time tR – 100 – mA/ns 1) Maximum duty cycle Dmax – – 100 % 2) P_5.2.11 ns 1) P_5.2.12 – ns 1) Minimum switch on-time TON,min – 100 – Minimum switch off- Time TOFF,min – Soft start ramp tstart 300 450 750 µs VFB rising from 5% to 95% of VFB,nom P_5.2.14 Input undervoltage shutdown threshold VS,off 3.75 – – V VS decreasing P_5.2.15 Input voltage startup threshold VS,on – 4.75 V VS increasing P_5.2.16 Input undervoltage shutdown hysteresis VS,hyst 130 300 – mV – P_5.2.17 5.3 V 1) P_5.2.18 – 1) P_5.2.19 Voltage threshold for transition from VPWM/PFM – PWM to PFM Frequency ratio for transition from PFM to PWM fPFM/PWM/ – fosc 200 – – 1.20 – PFM mode P_5.2.13 1) Specified by design. Not subject to production test. 2) Consider Chapter 4.2 Functional range . Data Sheet 15 Rev. 1.1 2018-03-07 TLF50211ELV50 2.2 MHz Step-Down Regulator 500 mA, 5 V, low quiescent current Buck regulator 5.3 Performance graphs Typical performance characteristics Line regulation PWM mode VS = 12 V; TJ = +25°C 5,100 5,075 5,075 5,050 5,050 5,025 5,025 650 550 450 4,900 350 4,900 650 4,925 550 4,925 450 4,950 350 4,950 250 4,975 150 4,975 250 5,000 150 5,000 50 VFB (V) 5,100 50 VFB (V) Load regulation PWM mode VS = 12 V; TJ = -43°C Icc (mA) Icc (mA) Load regulation PWM mode VS = 12 V; TJ = +150°C – 5,100 5,075 5,050 VFB (V) 5,025 5,000 4,975 4,950 650 550 450 350 250 150 4,900 50 4,925 Icc (mA) Data Sheet 16 Rev. 1.1 2018-03-07 TLF50211ELV50 2.2 MHz Step-Down Regulator 500 mA, 5 V, low quiescent current Buck regulator Line regulation PFM mode ICC = 100 µA; TJ = +25°C 5,128 5,112 5,112 5,096 5,096 5,08 5,08 45 40 35 30 Power stage on resistance: black TJ = +25°C light grey TJ = -43°C, dark grey TJ = +150°C Line regulation PFM mode ICC = 100 µA; TJ = +150°C 1,400 5,128 5,112 1,200 5,096 1,000 5,08 VS - Vswo (V) 5,064 5,048 0,800 0,600 VS (V) 0,7 0,6 0,5 0,4 0,3 0,2 45 40 35 30 25 20 0,000 15 5 10 0,200 5 5,016 0,1 0,400 5,032 0 VFB (V) 25 VS (V) VS (V) Data Sheet 20 45 5 40 5 35 5,016 30 5,016 25 5,032 20 5,032 15 5,048 10 5,048 15 5,064 10 5,064 5 VFB (V) 5,128 5 VFB (V) Line regulation PFM mode ICC = 100 µA; TJ = -43°C Iswo(A) 17 Rev. 1.1 2018-03-07 TLF50211ELV50 2.2 MHz Step-Down Regulator 500 mA, 5 V, low quiescent current Buck regulator Efficiency for VS = 13 V, fOSC = 1.65 MHz, LOUT = 4.7 µH Efficiency for VS = 13 V, fOSC = 1.65 MHz, LOUT = 10 µH 90,00% 90,00% 80,00% 80,00% 70,00% 70,00% 60,00% 60,00% 50,00% 50,00% 40,00% 40,00% 30,00% 30,00% 20,00% 20,00% 10,00% 0,00% 10,00% 0 100 200 300 400 ICC (mA) 500 0 600 Efficiency for VS = 13 V, fOSC = 2.2 MHz, LOUT = 4.7 µH 100 200 300 400 ICC (mA) 500 600 Efficiency for VS = 13 V, fOSC = 2.2 MHz, LOUT = 10 µH 90,00% 90,00% 80,00% 80,00% 70,00% 70,00% 60,00% 60,00% 50,00% 50,00% 40,00% 40,00% 30,00% 30,00% 20,00% 20,00% 10,00% 0,00% 10,00% 0 Data Sheet 100 200 300 400 ICC (mA) 500 0 600 18 100 200 300 ICC (mA) 400 500 600 Rev. 1.1 2018-03-07 TLF50211ELV50 2.2 MHz Step-Down Regulator 500 mA, 5 V, low quiescent current Enable and thermal shutdown 6 Enable and thermal shutdown 6.1 Description A valid high level at pin EN (VEN,hi) turns the regulator on, a valid low level at pin EN (VEN,lo) turns the regulator off. In off state the current consumption of the device is less than 2 µA. An integrated pull down resistor at pin EN (REN,INT) ensures, that the device is switched off, if pin EN is left open. The integrated thermal shutdown function turns off the power switch in case of overtemperature. The typical junction shutdown temperature is 175°C, with a min. of 155°C. After cooling down, the IC will automatically restart with a soft start into normal operation. The thermal shutdown is an integrated protection function designed to prevent IC destruction when operating under fault conditions. It should not be used for normal operation. 6.2 Electrical characteristics Enable, bias and thermal shutdown Table 5 Electrical characteristics: Enable, bias and thermal shutdown VS = 6.0 V to 40 V, Tj = -40°C to 150°C, all voltages with respect to ground (unless otherwise specified) Parameter Symbol Values Unit Note or Test Condition Number Min. Typ. Max. Enable EN Current consumption, shut down mode Iq,OFF Current consumption of VCC Iq,ON,V_CC – – 0.1 2 µA VEN = 0 V; Tj < 105°C; VS = 16 V P_6.2.1 – 60 µA VEN = 5.0 V; VS = 16 V; VCC = 5.4 V; Tj < 105°C; P_6.2.2 VEN = 5.0 V; VS = 16 V; VCC = 5.4 V; Tj < 105°C; P_6.2.3 PFM mode Current consumption of VS Iq,ON,V_S – 15 20 µA PFM mode Enable high signal valid VEN,hi 3.0 – – V – P_6.2.4 Enable low signal valid VEN,lo – – 0.8 V – P_6.2.5 Enable hysteresis VEN,HY 50 200 400 mV – P_6.2.6 Enable high input current IEN,hi – – 3 µA VEN = 16 V P_6.2.7 Enable low input current IEN,lo – 0.1 1 µA VEN = 0.5 V P_6.2.8 Enable internal resistor to GND REN,INT 7 12 20 MΩ VEN = 3 V P_6.2.9 195 °C 1) P_6.2.14 – K Internal overtemperature protection Overtemperature shutdown Tj,sd Overtemperature shutdown hysteresis Tj,sd_hyst - 155 175 15 P_6.2.15 1) Specified by design. Not subject to production test. Data Sheet 19 Rev. 1.1 2018-03-07 TLF50211ELV50 2.2 MHz Step-Down Regulator 500 mA, 5 V, low quiescent current Oscillator 7 Oscillator 7.1 Description The oscillator supplies the device with a constant frequency. The power switch will be switched on and off with a constant frequency fOSC. The time period TPWM is derived from this frequency and some safety functions are synchronized to this frequency. The oscillator frequency can be set by connecting an external resistor RFREQ between pin FREQ and GND using the following table (selected values, for more precise setting please refer to Figure 7). Frequency setting resistor Frequency adjusting resistor RFREQ 39 43 56 82 100 kΩ P_7.1.1 Oscillator frequency fosc 2400 2250 1800 1330 1100 kHz P_7.1.2 2,5 Switching Frequency [MHz] 2,35 2,2 2,05 1,9 1,75 1,6 1,45 1,3 1,15 1 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 Resistor at Freq pin [kΩ] Figure 7 Switching frequency fOSC versus frequency setting resistor RFREQ. The turn-on frequency can optionally be set externally via the SYNC pin. In this case the synchronization of the PWM-on signal refers to the falling edge of the SYNC-pin input signal. In case the synchronization to an external clock signal is not needed, the SYNC pin should be connected to ground. The frequency setting resistor RFREQ is also necessary for SYNC option and must be dimensioned according to the desired synchronization frequency (the ratio between synchronization and internal frequency has to be less than or equal to 1). The synchronization function is not available in PFM mode. Data Sheet 20 Rev. 1.1 2018-03-07 TLF50211ELV50 2.2 MHz Step-Down Regulator 500 mA, 5 V, low quiescent current Oscillator 7.2 Electrical characteristics buck regulator Table 6 Electrical characteristics: buck regulator VS = 6.0 V to 40 V, Tj = -40°C to 150°C, all voltages with respect to ground (unless otherwise specified) Parameter Symbol Values Unit Note or Number Test Condition Min. Typ. Max. fosc 2025 2250 2475 kHz VSYNC = 0 V; RFREQ = 43 kΩ P_7.2.1 fsync 1500 – 2200 kHz – P_7.2.2 P_7.2.3 Frequency setting FREQ Oscillator frequency spread Synchronization SYNC Synchronization capture range SYNC signal high level valid VSYNC,H 2.9 – – V 1) SYNC signal low level valid VSYNC,L – – 0.8 V 1) P_7.2.4 SYNC input internal pull-down RSYNC,INT 0.15 0.25 0.40 MΩ VSYNC = 5 V P_7.2.5 SYNC signal minimum high time tSYNC,H, min 50 – – ns – P_7.2.6 SYNC signal minimum low time tSYNC,L,min 50 – – ns – P_7.2.7 1) Synchronization of PWM-on signal to falling edge. Data Sheet 21 Rev. 1.1 2018-03-07 TLF50211ELV50 2.2 MHz Step-Down Regulator 500 mA, 5 V, low quiescent current Application information 8 Application information Note: The following information is given as a hint for the implementation of the device only and shall not be regarded as a description or warranty of a certain functionality, condition or quality of the device. LIN DIN VS CIN1 CIN2 LIN, CIN1 and CIN3 recommended for suppression of EME, DIN depending on application CIN3 VS TLF50211EL Over Temperature Shutdown EN Enable LOUT Buck Converter SWO VCC FREQ Oscillator INT. SUPPLY SYNC R5 DCATCH COUT FB Bandgap Reference Soft Start Ramp Generator N.C. N.C. N.C. N.C. N.C. GND GND N.C. Figure 8 Application diagram Note: This is a very simplified example of an application circuit. The function must be verified in the real application. Part-No. CIN2 CIN3 COUT DCATCH LOUT R5 Figure 9 Data Sheet Value 47μF/50V 100nF/50V 10μF/25V 1A/100V 10μH 47 kΩ Type electrolytic ceramic ceramic 10BQ100 Schottky MSS1278T 0.25 W Manufacturer AVX AVX AVX International Rectifier Coilcraft Panasonic Remark For improving EME 1 A current capability 4.7 μH also possible fOSC set to 2.2 MHz Bill of material for application diagram 22 Rev. 1.1 2018-03-07 TLF50211ELV50 2.2 MHz Step-Down Regulator 500 mA, 5 V, low quiescent current Application information 8.1 General layout recommendations Introduction: A switch mode step down converter is a potential source of electromagnetic disturbances which may affect the environment as well as the device itself and cause sporadic malfunction up to damages depending on the amount of noise. In principal we may consider the following basic effects: • radiated magnetic fields caused by circular currents, occurring mostly with the switching frequency and their harmonics; • radiated electric fields, often caused by (voltage) oscillations; • conducted disturbances (voltage spikes or oscillations) on the lines, mostly input and output lines. Radiated magnetic fields: Radiated magnetic fields are caused by circular currents occurring in so called “current windows”. These circular currents are alternating currents which are driven by the switching transistor. The alternating current in these windows are driving magnetic fields. The amount of magnetic emissions is mainly depending on the amplitude of the alternating current and the size of the so-called “window” (this is the area, which is defined by the circular current paths. We can divide into two windows: • the input current “window” (path consisting of CIN2, CIN3, LOUT and COUT): Only the alternate content of the input current IS is considered; • the output current “window” (path consisting of DCATCH, LOUT and COUT): Output current ripple ∆I. The area of these “windows” has to be kept as small as possible, with the relating elements placed next to each others as close as possible. It is highly recommended to use a ground plane as a single layer which covers the complete regulator area with all components shown in the application diagram. All connections to ground shall be as short as possible. Radiated electric fields: Radiated electric fields are caused by voltage oscillations occurring by stray inductances and stray capacitances at the connection between internal power stage (pin SWO), freewheeling diode DCATCH, and output capacitor COUT. They are also of course influenced by the commutation of the current from the internal power stage to the freewheeling diode DCATCH. Their frequencies might be above 100 MHz. Therefore, it is recommended to use a fast Schottky diode and to keep the connections in this area as low inductive as possible. This can be achieved by using short and broad connections and by arranging the related parts as close as possible. Following the recommendation of using a ground layer these low inductive connections will form together with the ground layer small capacitances which are desirable to damp the slope of these oscillations. The oscillations use connections or wires as antennas, this effect can also be minimized by the short and broad connections. Conducted disturbances: Conducted disturbances are voltage spikes or voltage oscillations, occurring permanently or by occasion mostly on the input or output connections. Comparable to the radiated electric fields they are caused by voltage stage, freewheeling diode DCATCH, and output capacitor COUT. Their frequencies might be above 100 MHz. They are super positioned to the input and output voltage and might therefore disturb other components of the application. The countermeasures against conducted disturbances are similar to the radiated electric fields: Data Sheet 23 Rev. 1.1 2018-03-07 TLF50211ELV50 2.2 MHz Step-Down Regulator 500 mA, 5 V, low quiescent current Application information • it is recommended to use short and thick connections between the single parts of the converter; • all parts shall be mounted close together; • additional filter capacitors (ceramic, with low ESR i.e CIN3 in the application diagram) in parallel to the output and input capacitor and as close as possible to the switching parts. Input and load current must be forced to pass these devices, do not connect them via thin lines. Recommended values from 10 nF to 220 nF; • for the input filter a so called π – Filter for maximum suppression might be necessary, which requires additional capacitors on the input. 8.2 Further application information • Please contact us for information regarding the FMEA pin • Existing Application Notes with more detailed information about the possibilities of this device • For further information you may contact http://www.infineon.com/ Data Sheet 24 Rev. 1.1 2018-03-07 TLF50211ELV50 2.2 MHz Step-Down Regulator 500 mA, 5 V, low quiescent current Package outlines 9 Package outlines 0.15 M C A-B D 14x 0.64 ±0.25 1 8 1 7 0.2 M D 8x Bottom View 3 ±0.2 A 14 6 ±0.2 D Exposed Diepad B 0.1 C A-B 2x 14 7 8 2.65 ±0.2 0.25 ±0.05 2) 0.08 C 8˚ MAX. C 0.65 0.1 C D 0.19 +0.06 1.7 MAX. Stand Off (1.45) 0 ... 0.1 0.35 x 45˚ 3.9 ±0.11) 4.9 ±0.11) Index Marking 1) Does not include plastic or metal protrusion of 0.15 max. per side 2) Does not include dambar protrusion PG-SSOP-14-1,-2,-3-PO V02 Figure 10 Package outline PG-SSOP-14 Green Product (RoHS compliant) To meet the world-wide customer requirements for environmentally friendly products and to be compliant with government regulations the device is available as a green product. Green products are RoHS-Compliant (i.e Pb-free finish on leads and suitable for Pb-free soldering according to IPC/JEDEC J-STD-020). For further information on alternative packages, please visit our website: http://www.infineon.com/packages. Data Sheet 25 Dimensions in mm Rev. 1.1 2018-03-07 TLF50211ELV50 2.2 MHz Step-Down Regulator 500 mA, 5 V, low quiescent current Revision history 10 Revision history Table 7 Revision history Revision Date Changes Rev 1.1 2018-03-06 P_7.2.6 Min value changed from 25 ns to 50 ns. P_7.2.7 Min value changed from 25 ns to 50 ns. Editorial changes. Rev 1.0 2013-06-19 Initial data sheet. Data Sheet 26 Rev. 1.1 2018-03-07 Trademarks All referenced product or service names and trademarks are the property of their respective owners. Edition 2018-03-07 Published by Infineon Technologies AG 81726 Munich, Germany © 2018 Infineon Technologies AG. All Rights Reserved. Do you have a question about any aspect of this document? Email: erratum@infineon.com Document reference IMPORTANT NOTICE The information given in this document shall in no event be regarded as a guarantee of conditions or characteristics ("Beschaffenheitsgarantie"). With respect to any examples, hints or any typical values stated herein and/or any information regarding the application of the product, Infineon Technologies hereby disclaims any and all warranties and liabilities of any kind, including without limitation warranties of non-infringement of intellectual property rights of any third party. In addition, any information given in this document is subject to customer's compliance with its obligations stated in this document and any applicable legal requirements, norms and standards concerning customer's products and any use of the product of Infineon Technologies in customer's applications. The data contained in this document is exclusively intended for technically trained staff. It is the responsibility of customer's technical departments to evaluate the suitability of the product for the intended application and the completeness of the product information given in this document with respect to such application. For further information on technology, delivery terms and conditions and prices, please contact the nearest Infineon Technologies Office (www.infineon.com). WARNINGS Due to technical requirements products may contain dangerous substances. For information on the types in question please contact your nearest Infineon Technologies office. Except as otherwise explicitly approved by Infineon Technologies in a written document signed by authorized representatives of Infineon Technologies, Infineon Technologies’ products may not be used in any applications where a failure of the product or any consequences of the use thereof can reasonably be expected to result in personal injury.