6N138

LOW INPUT CURRENT HIGH GAIN SPLIT DARLINGTON OPTOCOUPLERS SINGLE-CHANNEL 6N138 6N139 DESCRIPTION The 6N138/9 and HCPL-2730/HCPL-2731 optocouplers consist of an AlGaAs LED optically coupled to a high gain split darlington photodetector. The split darlington configuration separating the input photodiode and the first stage gain from the output transistor permits lower output saturation voltage and higher speed operation than possible with conventional darlington phototransistor optocoupler. In the dual channel devices, HCPL-2730/HCPL2731, an integrated emitter - base resistor provides superior stability over temperature. The combination of a very low input current of 0.5 mA and a high current transfer ratio of 2000% makes this family particularly useful for input interface to MOS, CMOS, LSTTL and EIA RS232C, while output compatibility is ensured to CMOS as well as high fan-out TTL requirements. An internal noise shield provides exceptional common mode rejection of 10 kV/µs. An improved package allows superior insulation permitting a 480 V working voltage compared to industry standard 220 V. 8 1 DUAL-CHANNEL HCPL-2730 HCPL-2731 8 1 8 1 FEATURES • • • • • • • Low current - 0.5 mA Superior CTR-2000% Superior CMR-10 kV/µs Double working voltage-480V RMS CTR guaranteed 0-70°C U.L. recognized (File # E90700) Dual Channel - HCPL-2730 HCPL-2731 APPLICATIONS • • • • • • Digital logic ground isolation Telephone ring detector EIA-RS-232C line receiver High common mode noise line receiver µP bus isolation Current loop receiver N/C 1 8 VCC +1 V F1 8 VCC +2 VF _ 3 7 VB _2 7 V01 6 VO _ VF2 3 6 V02 N/C 4 5 GND +4 5 GND 6N138 / 6N139 HCPL-2730 / HCPL-2731 ABSOLUTE MAXIMUM RATINGS Parameter Storage Temperature Operating Temperature Lead Solder Temperature EMITTER DC/Average Forward Input Current (No derating required up to 85°C) Symbol TSTG TOPR TSOL Each Channel Each Channel IF (avg) IF (pk) IF (trans) Each Channel Each Channel Each Channel (6N138 and 6N139) (6N138, HCPL-2730) (6N139, HCPL-2731) Each Channel VR PD IO (avg) VEB VCC, VO PD Value -55 to +125 -40 to +85 260 for 10 sec 20 40 1.0 5 35 60 0.5 -0.5 to 7 -0.5 to 18 100 Units °C °C °C mA mA A V mW mA V V mW Peak Forward Input Current (50% duty cycle, 1 ms P.W.) Peak Transient Input Current - (!"1 µs P.W., 300 pps) Reverse Input Voltage Input Power Dissipation DETECTOR Average Output Current Emitter-Base Reverse Voltage Supply Voltage, Output Voltage Output power dissipation 12/27/99 200023A LOW INPUT CURRENT HIGH GAIN SPLIT DARLINGTON OPTOCOUPLERS SINGLE-CHANNEL 6N138 6N139 DUAL-CHANNEL HCPL-2730 HCPL-2731 ELECTRICAL CHARACTERISTICS Parameter EMITTER Input Forward Voltage Input Reverse Breakdown Voltage (TA = 0 to 70°C unless otherwise specified.) INDIVIDUAL COMPONENT CHARACTERISTICS Test Conditions TA =25°C) Each Channel (IF = 1.6 mA) (TA = 25°C, IR = 10 µA) Each Channel (IF = 1.6 mA) Symbol VF BVR (#VF/#TA) Device All All All 6N139 IOH HCPL-2731 6N138 HCPL-2730 6N138 ICCL 6N139 HCPL-2731 HCPL-2730 6N138 ICCH 6N139 HCPL-2731 HCPL-2730 0.01 0.4 1.3 0.05 0.1 250 1.5 mA 3 10 µA 20 5.0 Min Typ** 1.30 Max 1.7 1.75 20 -1.8 0.01 100 Unit V V mV/°C µA Temperature coefficient of forward voltage DETECTOR (IF = 0 mA, VO = VCC = 18 V) Each Channel (IF = 0 mA, VO = VCC = 7 V) Each Channel (IF = 1.6 mA, VO = Open) (VCC = 18 V) (IF1 = IF2 = 1.6 mA, VCC = 18 V) (VO1 = VO2 = Open, VCC = 7 V) (IF = 0 mA, VO = Open) Logic high output current Logic low supply Logic high supply (VCC = 18 V) (IF1 = IF2 = 0 mA, VCC = 18 V) (VO1 = VO2 = Open, VCC = 7 V) ** All typicals at TA = 25°C 12/27/99 200023A LOW INPUT CURRENT HIGH GAIN SPLIT DARLINGTON OPTOCOUPLERS SINGLE-CHANNEL 6N138 6N139 DUAL-CHANNEL HCPL-2730 HCPL-2731 TRANSFER CHARACTERISTICS Parameter COUPLED Current transfer ratio (Notes 1,2) (TA = 0 to 70°C Unless otherwise specified) Test Conditions Symbol Device 6N139 HCPL-2731 CTR 6N139 HCPL-2731 6N138 HCPL-2730 6N139 6N139 HCPL-2731 6N139 VOL HCPL-2731 6N139 HCPL-2731 6N138 HCPL-2730 Min 400 500 300 Typ** 1100 3500 1300 2500 1300 2500 0.08 0.01 0.13 0.20 0.10 0.4 0.4 0.4 V 0.4 0.4 Max Unit % % % (IF = 0.5 mA, VO = 0.4 V, VCC = 4.5 V) Each Channel (IF = 1.6 mA, VO = 0.4 V, VCC = 4.5 V) Each Channel (IF = 1.6 mA, VO = 0.4 V, VCC = 4.5 V) Each Channel (IF = 0.5 mA, IO = 2 mA, VCC = 4.5 V) (IF = 1.6 mA, IO = 8 mA, VCC = 4.5 V) Each Channel Logic low output voltage (IF = 5 mA, IO = 15 mA, VCC = 4.5 V) output voltage (Note 2) Each Channel (IF = 12 mA, IO = 24 mA, VCC = 4.5 V) Each Channel (IF = 1.6 mA, IO = 4.8 mA, VCC = 4.5 V) Each Channel ** All typicals at TA = 25°C 12/27/99 200023A LOW INPUT CURRENT HIGH GAIN SPLIT DARLINGTON OPTOCOUPLERS SINGLE-CHANNEL 6N138 6N139 SWITCHING CHARACTERISTICS Parameter DUAL-CHANNEL HCPL-2730 HCPL-2731 (TA = 0 to 70°C unless otherwise specified., VCC = 5 V) Symbol Device 6N139 4 HCPL-2731 6N139 TPHL HCPL-2730 HCPL-2731 6N138 0.3 1.5 3 0.2 Min Typ** Max 30 25 120 100 2 1 3 2 15 10 25 1 20 90 12 22 1.3 60 10 7 15 5 10 50 7 16 35 µs µs Unit Test Conditions (RL = 4.7 k$, IF = 0.5 mA) TA = 25°C (RL = 4.7 k$, IF = 0.5 mA) Each Channel TA = 25°C TA = 25°C (RL = 270 $, IF = 12 mA) Each Channel TA = 25°C TA = 25°C (RL = 2.2 k$, IF = 1.6 mA) Each Channel TA = 25°C (RL = 2.2 k$, IF = 1.6 mA) Propagation delay time to logic low (Note 2) (Fig. 22) (RL = 270 $, IF = 12 mA) HCPL-2731 HCPL-2730 6N139 HCPL-2731 6N139 HCPL-2731 6N139 TPLH HCPL-2730 HCPL-2731 6N138 HCPL-2730/1 6N138 HCPL-2730/1 6N138 |CMH| 6N139 HCPL-2730 HCPL-2731 6N138 |CML| 6N139 HCPL-2730 HCPL-2731 1,000 10,000 1,000 10,000 (RL = 4.7 k$, IF = 0.5 mA) Each Channel (RL = 4.7 k$, IF = 0.5 mA) TA = 25°C Each Channel (RL = 270 $, IF = 12 mA) Propagation delay time to logic high (Note 2) (Fig. 22) TA = 25°C (RL = 270 $, IF = 12 mA) Each Channel TA = 25°C (RL = 2.2 k$, IF = 1.6 mA) Each Channel (RL = 2.2 k$, IF = 1.6 mA) TA = 25°C Each Channel Common mode transient immunity at logic high Common mode transient immunity at logic low ** All typicals at TA = 25°C (IF = 0 mA, %VCM% = 10 VP-P) TA = 25°C, (RL = 2.2 k$) (Note 3) (Fig. 23) Each Channel (IF = 1.6 mA, %VCM% = 10 VP-P, RL = 2.2 k$) TA = 25°C (Note 3) (Fig. 23) Each Channel V/µs V/µs 12/27/99 200023A LOW INPUT CURRENT HIGH GAIN SPLIT DARLINGTON OPTOCOUPLERS SINGLE-CHANNEL 6N138 6N139 ISOLATION CHARACTERISTICS Characteristics Input-output insulation leakage current (TA = 0 to 70°C Unless otherwise specified) Test Conditions (Relative humidity = 45%) (TA = 25°C, t = 5 s) (VI-O = 3000 VDC) (Note 8) Withstand insulation test voltage Resistance (input to output) Capacitance (input to output) Input-Input Insulation leakage current Input-Input Resistance Input-Input Capacitance ** All typicals at TA = 25°C (RH ! 50%, TA = 25°C) (Note 4) ( t = 1 min.) (Note 4) (VI-O = 500 VDC) (Note 4,5) (f = 1 MHz) t = 5 s, (HCPL-2730/2731 only) (VI-I = 500 VDC) (Note 6) (HCPL-2730/2731 only) (f = 1 MHz) (Note 6) (HCPL-2730/2731 only) VISO RI-O CI-O II-I RI-I CI-I 2500 1012 0.6 0.005 1011 0.03 VRMS $ pF µA $ pF II-O 1.0 µA Symbol Min Typ** Max Unit DUAL-CHANNEL HCPL-2730 HCPL-2731 (RH ! 45%, VI-I = 500 VDC) (Note 6) NOTES 1. Current Transfer Ratio is defined as a ratio of output collector current, IO, to the forward LED input current, IF, times 100%. 2. Pin 7 open. (6N138 and 6N139 only) 3. Common mode transient immunity in logic high level is the maximum tolerable (positive) dVcm/dt on the leading edge of the common mode pulse signal, VCM, to assure that the output will remain in a logic high state (i.e., VO&2.0 V). Common mode transient immunity in logic low level is the maximum tolerable (negative) dVcm/dt on the trailing edge of the common mode pulse signal, VCM, to assure that the output will remain in a logic low state (i.e., VO'0.8 V). 4. Device is considered a two terminal device: Pins 1, 2, 3 and 4 are shorted together and Pins 5, 6, 7 and 8 are shorted together. 5. For dual channel devices, CI-O is measured by shorting pins 1 and 2 or pins 3 and 4 together and pins 5 through 8 shorted together. 6. Measured between pins 1 and 2 shorted together, and pins 3 and 4 shorted together. 12/27/99 200023A LOW INPUT CURRENT HIGH GAIN SPLIT DARLINGTON OPTOCOUPLERS SINGLE-CHANNEL 6N138 6N139 ELECTRICAL CHARACTERISTICS Current Limiting Resistor Calculations R1 (Non-Invert) = VDD1 - VDF - VOL1 IF R1 (Invert) = VDD1 - VOH1 - VDF IF R2 = VDD2 - = VOLX (@ IL - I2) IL (TA = 25°C unless otherwise specified) DUAL-CHANNEL HCPL-2730 HCPL-2731 INPUT Where: VDD1 - Input Supply Voltage VDD2 - Output Supply Voltage VDF - Diode Forward Voltage VOL1 - Logic “0” Voltage of Driver VOH1 - Logic “1” Voltage of Driver IF - Diode Forward Current VOLX - Saturation Voltage of Output Transistor IL - Load Current Through Resistor R2 I2 - Input Current of Output Gate NON-INV. INV. NON-INV. INV. NON-INV. 74XX INV. NON-INV. 74LXX INV. NON-INV. 74SXX INV. NON-INV. 74LSXX INV. NON-INV. 74HXX INV. CMOS @5V CMOS @ 10 V R1 ($) 2000 510 5100 4700 2200 180 1800 100 2000 360 2000 180 2000 180 OUTPUT CMOS CMOS 74XX 74LXX 74SXX 74LSXX 74HXX @ 5 V @ 10 V R2 ($) R2 ($) R2 ($) R2 ($) R2 ($) R2 ($) R2 ($) 1000 2200 750 1000 1000 1000 560 Fig. 1 Resistor Values for Logic Interface VDD1 VDD2 VDD2 1 2 3 IN R1 8 7 6 OUT R1 R2 IN 1 2 3 4 8 7 6 5 R2 OUT 4 5 Fig. 2 Non-Inverting Logic Interface Fig. 3 Inverting Logic Interface 12/27/99 200023A LOW INPUT CURRENT HIGH GAIN SPLIT DARLINGTON OPTOCOUPLERS SINGLE-CHANNEL 6N138 6N139 Fig. 4 LED Forward Current vs. Forward Voltage 100 1.5 IF = 1.6 mA 10 TA = 85˚C DUAL-CHANNEL HCPL-2730 HCPL-2731 Fig. 5 LED Forward Voltage vs. Temperature FORWARD CURRENT - IF (mA) FORWARD VOLTAGE - VF (V) TA = 25˚C TA = -40˚C 1.4 1 TA = 70˚C 1.3 0.1 1.2 0.01 TA = 0˚C 0.001 1.0 1.1 1.1 1.2 1.3 1.4 1.5 1.6 -40 -20 0 20 40 60 80 100 FORWARD VOLTAGE - VF (V) TEMPERATURE - TA (˚C) Fig. 6 Non-saturated Rise and Fall Times vs. Load Resistance (6N138 / 6N139 Only) 100 TA = 25˚C Fig. 7 Non-saturated Rise and Fall Times vs. Load Resistance (HCPL-2730 / HCPL-2731 Only) TA = 25˚C tf tf 10 TIME, T (µs) 10 TIME - µs tr tr 1 0.1 IF ADJUSTED FOR VOL = 2 V 1 0.1 1 10 1 10 RL - LOAD RESISTANCE (k$) RL - LOAD RESISTANCE (k$) Fig. 8 Current Transfer Ratio vs. Forward Current (6N138 / 6N139 Only) Fig. 9 Current Transfer Ratio vs. Forward Current (HCPL-2730 / HCPL-2731 Only) 5000 VCC = 5 V VO = 0.4 V CURRENT TRANSFER RATIO - CTR (%) 1600 VCC = 5 V VO= 0.4 V CTR - CURRENT TRANSFER RATIO - % 4000 TA = 70˚C TA = 85˚C TA = 25˚C 1200 3000 TA = 0˚C 800 2000 TA = 70˚C 400 TA = -40˚C 0 0.01 TA = 25˚C TA = 0˚C 1000 0.1 1 10 0 0.1 1 10 100 IF - FORWARD CURRENT (mA) IF - FORWARD CURRENT - mA 12/27/99 200023A O TA = -40˚C C TA = 85˚C ( ) LOW INPUT CURRENT HIGH GAIN SPLIT DARLINGTON OPTOCOUPLERS SINGLE-CHANNEL 6N138 6N139 Fig. 10 Output Current vs Output Voltage (6N138 / 6N139 Only) 60 VCC = 5V TA = 25˚C 50 5 mA 4.5 mA 4 mA 3.5 mA 100 3 mA 120 TA = 25˚C VCC = 5.0 V IF = 4.0 mA IF = 5.0 mA IF = 4.5 mA DUAL-CHANNEL HCPL-2730 HCPL-2731 Fig. 11 Output Current vs Output Voltage (HCPL-2730 / HCPL-2731 Only) IO - OUTPUT CURRENT (mA) IO-OUTPUT CURRENT - mA IF = 3.5 mA 80 IF = 3.0 mA IF = 2.5 mA 60 IF = 2.0 mA IF = 1.5 mA 40 IF = 1.0 mA 40 2.5 mA 2 mA 30 1.5 mA 20 1 mA 10 20 IF = 0.5 mA 0 0 1 2 0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0 VO - OUTPUT VOLTAGE (V) VO-OUTPUT VOLTAGE - V Fig. 12 Output Current vs. Input Diode Forward Current (6N138 / 6N139 Only) 100 100 Fig. 13 Output Current vs Input Diode Forward Current (HCPL-2730 / HCPL-2731 Only) VCC = 5.0 V VO = 0.4 V TA = 85˚C IO - OUTPUT CURRENT (mA) VCC = 5 V 10 VO = 0.4 V IO - OUTPUT CURRENT - mA 10 TA = 25˚C 1 1 TA = -40˚C TA = 85˚C 0 TA = 70˚C TA = 25˚C TA = 0˚C TA = -40˚C 0 0.01 0.1 1 10 0.1 0.1 1 10 100 IF - INPUT DIODE FORWARD CURRENT (mA) IF - INPUT DIODE FORWARD CURRENT - mA Fig. 14 Logic Low Supply Current vs. Input Diode Forward Current (6N138 / 6N139 Only) 4.0 100 Fig. 15 Logic Low Supply Current vs. Input Diode Forward Current (HCPL-2730 / HCPL-2731 Only) ICCL - LOGIC LOW SUPPLY CURRENT - mA TA = 25˚C ICCL - LOGIC LOW SUPPLY CURRENT (mA) 3.5 3.0 HCPL-2731 VCC = 18 V 10 2.5 VCC = 5 V 2.0 VCC = 18 V 1.5 HCPL-2730 HCPL-2731 VCC = 7 V 1 1.0 0.5 0.0 0 2 4 6 8 10 12 14 16 0.1 0.1 1 10 100 IF - FORWARD CURRENT (mA) IF - INPUT DIODE FORWARD CURRENT - mA 12/27/99 200023A LOW INPUT CURRENT HIGH GAIN SPLIT DARLINGTON OPTOCOUPLERS SINGLE-CHANNEL 6N138 6N139 Fig. 16 Propagation Delay vs. Input Diode Forward Current (6N138 / 6N139 Only) 70 DUAL-CHANNEL HCPL-2730 HCPL-2731 Fig. 17 Propagation Delay vs. Input Diode Forward Current (HCPL-2730 / HCPL-2731 Only) 70 VCC = 5 V TA = 25˚C 60 VCC = 5 V TA = 25˚C 60 tP - PROPAGATION DELAY - µs 50 tP - PROPAGATION DELAY - µs 50 (tPHL) RL = 2.2 kΩ or 4.7 kΩ 40 (tPHL) RL = 2.2 kΩ or 4.7 kΩ 40 30 30 (tPLH) RL = 4.7 kΩ (tPLH) RL = 2.2 kΩ 20 (tPLH) RL = 4.7 kΩ 20 10 10 (tPLH) RL = 2.2 kΩ 0 0 0 1 2 3 4 5 6 7 8 9 10 0 2 4 6 8 10 IF - INPUT DIODE FORWARD CURRENT - mA IF - INPUT DIODE FORWARD CURRENT - mA Fig. 18 Propagation Delay to Logic Low vs. Pulse Period (6N138 / 6N139 Only) 100 Fig. 19 Propagation Delay to Logic Low vs. Pulse Period (HCPL-2730 / HCPL-2731 Only) 100 tPHL - PROPAGATION DELAY to LOGIC LOW - µs 6N139 IF = 0.5 mA RL = 4.7 kΩ 10 tPHL - PROPAGATION DELAY to LOGIC LOW - µs 10 HCPL-2731 IF = 0.5 mA RL = 4.7 kΩ 6N138 IF = 1.6 mA RL = 2.2 kΩ 1 1 HCPL-2730 HCPL-2731 IF =1.6 mA RL = 2.2kΩ TA = 25˚C TA = 25˚C 0.1 0.01 0.1 1 10 0.1 0.01 0.1 1 10 T - INPUT PULSE PERIOD - ms T - INPUT PULSE PERIOD - ms Fig. 20 Propagation Delay vs. Temperature (6N138 / 6N139 Only) 50 HCPL-2730 : IF = 1.6 mA, RL = 2.2 k HCPL-2731 : IF = 0.5 mA, RL = 4.7 k 40 40 50 Fig. 21 Propagation Delay vs. Temperature (HCPL-2730 / HCPL-2731 Only) HCPL-2730 : IF = 1.6 mA, RL = 2.2 k HCPL-2731 : IF = 0.5 mA, RL = 4.7 k tP - PROPAGATION DELAY - µs tPLH (HCPL-2731) 30 tP - PROPAGATION DELAY - µs tPLH (HCPL-2731) 30 20 tPLH (HCPL-2730) 20 tPLH (HCPL-2730) 10 tPHL (HCPL-2731) tPHL (HCPL-2730) 10 tPHL (HCPL-2731) tPHL (HCPL-2730) 0 0 10 20 30 40 50 60 70 80 0 0 10 20 30 40 50 60 70 80 TA - TEMPERATURE (˚C) TA - TEMPERATURE (˚C) 12/27/99 200023A LOW INPUT CURRENT HIGH GAIN SPLIT DARLINGTON OPTOCOUPLERS SINGLE-CHANNEL 6N138 6N139 Noise Shield VCC Pulse Generator tr = 5ns Z O = 50 $ IF + Noise Shield VCC RL V01 0.1 µF VO CL = 15 µF* DUAL-CHANNEL HCPL-2730 HCPL-2731 Pulse Generator I F tr = 5ns Z O = 50 $ 10% D.C. I/ f < 100 (s 1 + 8 7 6 5 +5 V 1 VF1 - 8 7 6 5 +5 V 2 VF - VB RL 10% DUTY CYCLE I/f < 100 µS VO 2 - 3 I F Monitor Rm VO 0.1 µF IF MONITOR Rm C L = 15 µF* 3 4 V02 VF2 + GND 4 GND Test Circuit for 6N138, 6N139 Test Circuit for HCPL-2730 and HCPL-2731 IF 0 VO 5V 1.5 V 1.5 V VOL TPHL TPLH Fig. 22 Switching Time Test Circuit *Includes Probe and Fixture Capacitance IF Noise Shield 1 + Noise Shield 8 7 6 5 VCC +5 V IF + VF1 A 1 2 3 4 8 7 6 5 VCC RL V01 0.1 µF +5 V 2 A B VFF VF - VB RL B VO 0.1 µF VFF VO 3 4 + VCM VO VF2 + V02 GND - GND - Pulse Gen + VCM - Pulse Gen Test Circuit for 6N138 and 6N139 Test Circuit for HCPL-2730 and HCPL-2731 VCM 10 V 10% tr 90% 90% 10% tf 0V VO Switch at A : I F = 0 mA VO Switch at B : I F = 1.6 mA 5V VOL Fig. 23 Common Mode Immunity Test Circuit 12/27/99 200023A LOW INPUT CURRENT HIGH GAIN SPLIT DARLINGTON OPTOCOUPLERS SINGLE-CHANNEL 6N138 6N139 Package Dimensions (Through Hole) PIN 1 ID. DUAL-CHANNEL HCPL-2730 HCPL-2731 Package Dimensions (Surface Mount) 0.390 (9.91) 0.370 (9.40) 4 4 3 2 1 0.270 (6.86) 0.250 (6.35) 5 6 7 8 3 2 1 PIN 1 ID. 0.270 (6.86) 0.250 (6.35) 0.390 (9.91) 0.370 (9.40) 5 0.070 (1.78) 0.045 (1.14) 6 7 8 SEATING PLANE 0.070 (1.78) 0.045 (1.14) 0.300 (7.62) TYP 0.200 (5.08) 0.115 (2.92) 0.020 (0.51) MIN 0.154 (3.90) 0.120 (3.05) 0.022 (0.56) 0.016 (0.41) 0.020 (0.51) MIN 0.016 (0.41) 0.008 (0.20) 0.045 [1.14] 15° MAX 0.016 (0.40) 0.008 (0.20) 0.100 (2.54) TYP 0.300 (7.62) TYP 0.022 (0.56) 0.016 (0.41) 0.100 (2.54) TYP 0.315 (8.00) MIN 0.405 (10.30) MIN Lead Coplanarity : 0.004 (0.10) MAX Package Dimensions (0.4”Lead Spacing) 4 3 2 1 PIN 1 ID. 0.270 (6.86) 0.250 (6.35) 5 6 7 8 0.390 (9.91) 0.370 (9.40) SEATING PLANE 0.070 (1.78) 0.045 (1.14) 0.200 (5.08) 0.115 (2.92) 0.004 (0.10) MIN 0.154 (3.90) 0.120 (3.05) 0.022 (0.56) 0.016 (0.41) NOTE All dimensions are in inches (millimeters) 0° to15° 0.016 (0.40) 0.008 (0.20) 0.100 (2.54) TYP 0.400 (10.16) TYP 12/27/99 200023A LOW INPUT CURRENT HIGH GAIN SPLIT DARLINGTON OPTOCOUPLERS SINGLE-CHANNEL 6N138 6N139 ORDERING INFORMATION Order Entry Identifier .R2 .S .SD .W DUAL-CHANNEL HCPL-2730 HCPL-2731 Option R2 S SD W Description Opto Plus Reliability Conditioning Surface Mount Lead Bend Surface Mount; Tape and reel 0.4” Lead Spacing QT Carrier Tape Specifications (“D” Taping Orientation) 12.0 ± 0.1 4.90 ± 0.20 4.0 ± 0.1 0.30 ± 0.05 4.0 ± 0.1 Ø1.55 ± 0.05 1.75 ± 0.10 7.5 ± 0.1 13.2 ± 0.2 16.0 ± 0.3 10.30 ± 0.20 0.1 MAX 10.30 ± 0.20 Ø1.6 ± 0.1 User Direction of Feed Corporate Headquarters QT Optoelectronics 610 North Mary Avenue Sunnyvale, CA 94086 (408) 720-1440 Phone (408) 720-0848 Fax European Sales QT Optoelectronics “Le Levant” 2, rue du Nouveau Bercy F-94277-CHARENTON-LE PONT Cedex FRANCE 33 [0] 1.45.18.78.78 Phone 33 [0] 1.43.75.77.57 Fax North American Sales QT Optoelectronics 16775 Addison Rd.,Suite 200 Addison, TX 75001 (972) 447-1300 Phone (972) 447-0784 Fax Asia/Pacific Sales QT Optoelectronics B613, 6th Floor East Wing, Wisma Tractors Jalan SS16/1, Subang Jaya 47500 Petaling Jaya Selangor Darul Eshan, Malaysia 603/735-2417 Phone 603/736-3382 Fax European Sales Quality Technologies Deutschland GmbH Max-Huber-Strasse 8 D-85737 Ismaning, Germany 49 [0] 89/96.30.51 Phone 49 [0] 89/96.54.74 Fax European Sales Quality Technologies (U.K) Ltd. 10, Prebendal Court, Oxford Road Aylesbury, Buckinghamshire HP19-3EY United Kingdom 44 [0] 1296/30.44.99 Phone 44 [0] 1296/39.24.32 Fax 12/27/99 200023A LOW INPUT CURRENT HIGH GAIN SPLIT DARLINGTON OPTOCOUPLERS DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. LIFE SUPPORT POLICY FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury of the user. 2. A critical component in any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. www.fairchildsemi.com © 2000 Fairchild Semiconductor Corporation 12/27/99 200023A