6N138

L IT E - O N T E CH NO L O G Y CO RP O RAT IO N Property of Lite-on Only 6N138, 6N139 Single Channel, High Speed Optocouplers Dec.2008 Description These high gain series couplers use a light emitter diode and an integrated high gain photo detector to provide extremely high current transfer ratio between input and output. Separate pins for the photodiode and output stage result in TTL compatible saturation voltage and high speed operation. Where desired the Vcc and Vo terminals may be tied together to achieve conventional photo darlington operation. A base access terminal allows a gain bandwidth adjustment to be made. Features • • • • High current transfer ratio – 2000% typical. Low input current requirements – 0.5mA High output current – 60mA CTR guarantee – 0~70℃. Instantaneous common mode rejection 10KV/μsec TTL compatible output – 0.1V VOL typical UL, CSA approved. Functional Diagram NC ANODE VCC • • • VB Cathode VO NC 6N138 / 6N139 GND APPLICATIONS Truth Table (Positive Logic) LED OUT ON L OFF H A 0.1µF bypass Capacitor must be connected between Pin8 and Pin5 • • • • • • Digital logic ground isolation Low input current line receiver Telephone ring detector EIA-RS-232C line receiver Current loop receiver High common mode noise line receiver Part No. : 6N138 / 6N139 series BNS-OD-C131/A4 Page : 1 of 15 L IT E - O N T E CH NO L O G Y CO RP O RAT IO N Property of Lite-on Only Ordering Information Minimum CMR Part Option dV/dt (V/µs) VCM (V) CTR Remarks Single Channel, DIP-8 6N138 M S 1,000 10 300 400 Single Channel, Wide Lead Spacing Single Channel, SMD-8 Single Channel, DIP-8 6N139 M S Single Channel, Wide Lead Spacing Single Channel, SMD-8 Part No. : 6N138 / 6N139 series BNS-OD-C131/A4 Page : 2 of 15 L IT E - O N T E CH NO L O G Y CO RP O RAT IO N Property of Lite-on Only OUTLINE DIMENSIONS 8-pin DIP Package (6N138 / 6N139) *1. Year date code. *2. 2-digit work week. *3. Factory identification mark (Z : Taiwan, Y : Thailand). Dimensions are in Millimeters and (Inches). Part No. : 6N138 / 6N139 series BNS-OD-C131/A4 Page : 3 of 15 L IT E - O N T E CH NO L O G Y CO RP O RAT IO N Property of Lite-on Only OUTLINE DIMENSIONS 8-pin DIP Wide Lead Spacing Package (6N138M / 6N139M) *1. Year date code. *2. 2-digit work week. *3. Factory identification mark (Z : Taiwan, Y : Thailand). Dimensions are in Millimeters and (Inches). Part No. : 6N138 / 6N139 series BNS-OD-C131/A4 Page : 4 of 15 L IT E - O N T E CH NO L O G Y CO RP O RAT IO N Property of Lite-on Only OUTLINE DIMENSIONS 8-pin DIP Surface Mount Package (6N138S / 6N139S) *1. Year date code. *2. 2-digit work week. *3. Factory identification mark (Z : Taiwan, Y : Thailand). Dimensions are in Millimeters and (Inches). Part No. : 6N138 / 6N139 series Page : 5 of 15 L IT E - O N T E CH NO L O G Y CO RP O RAT IO N Property of Lite-on Only TAPING DIMENSIONS 6N138S/6N139S-TA 6N138S/6N139S-TA1 Description Tape wide Pitch of sprocket holes Distance of compartment Distance of compartment to compartment Symbol W P0 F P2 P1 Dimensions in millimeters ( inches ) 16 ± 0.3 ( .63 ) 4 ± 0.1 ( .15 ) 7.5 ± 0.1 ( .295 ) 2 ± 0.1 ( .079 ) 12 ± 0.1 ( .472 ) Part No. : 6N138 / 6N139 series BNS-OD-C131/A4 Page : 6 of 15 L IT E - O N T E CH NO L O G Y CO RP O RAT IO N Property of Lite-on Only Recommended Lead Free Reflow Profile Part No. : 6N138 / 6N139 series BNS-OD-C131/A4 Page : 7 of 15 L IT E - O N T E CH NO L O G Y CO RP O RAT IO N Property of Lite-on Only Absolute Maximum Ratings*1 Parameter Storage Temperature Operating Temperature Isolation Voltage Supply Voltage Lead Solder Temperature * 2 Input Average Forward Input Current Reverse Input Voltage Input Power Dissipation Output Average Output Current IO 6N138 6N139 6N138 Supply Voltage, Output Voltage Vcc, VO 6N139 Output Collector Power Dissipation PO 6N138 6N139 -0.5 18 100 mW -0.5 50 7 V mA IF VR PI 6N138 6N139 20 5 35 mA V mW Symbol TST TA VISO VCC TSOL 6N138 6N139 Device Min -55 -20 5000 15 260 TYP Max 125 85 Units o C C o VRMS V °C 1.Ambient temperature = 25oC, unless otherwise specified. Stresses exceeding the absolute maximum ratings can cause permanent damage to the device. Exposure to absolute maximum ratings for long periods of time can adversely affect reliability. 2. 260oC for 10 seconds. Refer to Lead Free Reflow Profile. Part No. : 6N138 / 6N139 series BNS-OD-C131/A4 Page : 8 of 15 L IT E - O N T E CH NO L O G Y CO RP O RAT IO N Property of Lite-on Only Electrical Specifications Parameters Input Input Forward Voltage Input Forward Voltage Temperature Coefficient Input Reverse Voltage Input Capacitance Detector IF=1.6mA;Vo=0.4V; Vcc=4.5V Current transfer ratio IF=0.5mA;Vo=0.4V; Vcc=4.5V IF=1.6mA;Vcc=0.4V; Vcc=4.5V IF=1.6mA;Vcc=4.5V; Io=4.8mA IF=0.5mA;Vcc=4.5V; Io=2mA IF=1.6mA;Vcc=4.5V; Io=8mA IF=5mA;Vcc=4.5V; Io=15mA IF=12mA;Vcc=4.5V; Io=24mA IF=0mA, Vo=Vcc=7V TA=25℃ Logic high output current IF=0mA, Vo=Vcc=18V TA=25℃ Logic low supply current IF=1.6mA, Vo=open (Vcc=18V) IF=0mA, Vo=open ; TA=25℃ (Vcc=18V) IccL IOH 6N139 6N138 6N139 6N138 6N139 0.1 100 mA CTR 6N139 500 6N138 1600 0.1 2600 0.4 6N138 300 400 1600 2000 2600 5000 % IF =1.6mA, TA=25℃ IF=1.6mA Test Condition Symbol Device Min Typ Max Units VF ∆VF/∆Ta 6N138 6N139 BVR CIN 5 - 1.1 -1.9 60 1.7 V mV/℃ IR = 10µA TA=25℃ VF=0; f=1MHZ - V pF Logic low output voltage VOL 6N139 - 0.1 0.4 V 6N138 - 0.2 0.05 250 μA - 0.4 1.5 Logic high supply current *All Typical at TA =25°C IccH - 0.01 10 uA Part No. : 6N138 / 6N139 series BNS-OD-C131/A4 Page : 9 of 15 L IT E - O N T E CH NO L O G Y CO RP O RAT IO N Property of Lite-on Only SWITCHING SPECIFICATIONS (AC) TA=0~70℃, Vcc=5V, unless otherwise specified. Parameter Test Condition IF=1.6mA; RL= 2.2kΩ Propagation Delay Time to Low Output Level IF=0.5mA; RL=4.7KΩ IF=12mA; RL=270Ω IF=1.6mA; RL= 2.2kΩ Propagation Delay Time to High Output Level IF=0.5mA; RL=4.7KΩ IF=12mA; RL=270Ω tPLH 6N139 2 7 KV/µs Logic High Common Mode Transient Immunity IF=0mA; |VCM|=10Vp-p RL=2.2KΩ |CMH| 6N138 6N139 1 10 KV/µs KV/µs |CML| 6N138 6N139 1 10 KV/µs 6N138 tPHL 6N139 0.1 10 18 1 35 60 μs Symbol Device 6N138 Min Typ 1.6 5 Max 10 25 μs Units Logic Low Common Mode Transient Immunity *All Typical at TA =25°C IF=1.6mA; |VCM|=10Vp-p RL=2.2K Ω Part No. : 6N138 / 6N139 series BNS-OD-C131/A4 Page : 10 of 15 L IT E - O N T E CH NO L O G Y CO RP O RAT IO N Property of Lite-on Only Isolation Characteristics Parameter Input-Output Insulation Leakage Current W ithstand Insulation Test Voltage Input-Output Resistance *All Typical at TA =25°C Notes, 1. AC For 1 Minute, R.H. = 40 ~ 60%. Isolation voltage shall be measured using the following method. (1) Short between anode and cathode on the primary side and between collector and emitter on the secondary side. (2) The isolation voltage tester with zero-cross circuit shall be used. (3) The waveform of applied voltage shall be a sine wave. 2. For 10 Seconds 3. Current Transfer Ratio (CTR) is defined as the ration of output collector current, Io, to the forward LED input current, IF, times 100%. 4. Pin 7 open. 5. Instantaneous common mode rejection voltage "output (1)" represents a common mode voltage variation that can hold the output above (1) level (Vo>2.0V).Instantaneous common mode rejection voltage "output (0)" represents a common mode voltage variation that can hold the output above (0) level (Vo