QVE00112

OPTOLOGIC® OPTICAL INTERRUPTER SWITCH QVE00112 PACKAGE DIMENSIONS 0.714 (18.150) 0.123 (3.125) 0.246 0.276 (6.250) (7.012) 0.014 (0.356) 0.316 (8.025) 0.118 (3.000) Ø 3.300 0.173 (4.400) 0.173 (4.400) 0.102 (2.600) 0.327 (8.310) OPTICAL C L 0.327 (8.310) 0.189 (4.820) 0.617 (15.67) 0.100 (2.540) 13.78 (350) ± 0.275 (7) GREEN (GND) WHITE (VOUT) GRAY (VCC) GRN WHT GRY 0.464 (11.800) 0.143 (3.625) NOTES: 1. Dimensions for all drawings are in inches (millimeters). 2. Tolerance of ± .010 (.25) on all non-nominal dimensions unless otherwise specified. 3. Wire gauge: 24 AWG, 7 strand, pre-tinned copper. FEATURES • No contact switching • Mounting tab • Wire leads for remote connection • 3 mm slot • Output configuration: Inverter open-collector • TTL/CMOS compatible output • Aperture width: .014" © 2004 Fairchild Semiconductor Corporation Page 1 of 5 6/10/04 OPTOLOGIC® OPTICAL INTERRUPTER SWITCH QVE00112 ABSOLUTE MAXIMUM RATINGS (TA = 25°C unless otherwise specified) Parameter Operating Temperature Storage Temperature Soldering Temperature (Iron)(2,3,4) EMITTER Continuous Forward Current Reverse Voltage Power Dissipation(1) SENSOR Output Current Supply Voltage Output Voltage Power Dissipation(2) IO VCC VD PD 50 16 30 150 mA V V mW IF VR PD 50 5 100 mA V mW Symbol TOPR TSTG TSOL-I Rating -40 to +85 -40 to +85 240 for 5 sec Units °C °C °C NOTES (Applies to Max Ratings and Characteristics Tables.) 1. Derate power dissipation linearly 1.67 mW/°C above 25°C. 2. Derate power dissipation linearly 2.50 mW/°C above 25°C. 3. RMA flux is recommended. 4. Methanol or isopropyl alcohols are recommended as cleaning agents. ELECTRICAL/OPTICAL CHARACTERISTICS (TA =25°C) PARAMETER Operating Supply Voltage INPUT DIODE Forward Voltage Reverse Leakage Current COUPLED Operating Supply Current Low Level Output Voltage High Level Output Current Hysteresis Ratio Propagation Delay Output Rise and Fall Time VCC = 5 V, RL = 360 Ω VCC = 5 V, RL = 360 Ω tPLH, tPHL tr, tf VCC = 16 V VCC = 5 V, RL = 360 Ω VCC = 5 V, VOH = 30 V (Light Path Blocked) ICC VOL IOH — — — — — — — 1.2 5 70 — 12 0.4 100 — — — µs ns mA V µA IF = 20 mA VR = 5 V VF IR — — — — 1.7 10 V µA TEST CONDITIONS SYMBOL VCC MIN. 4.5 TYP. — MAX. 5.5 UNITS V © 2004 Fairchild Semiconductor Corporation Page 2 of 5 6/10/04 OPTOLOGIC® OPTICAL INTERRUPTER SWITCH QVE00112 Fig. 1 Output Voltage Vs. Shield Distance (Vertical) 6 6 Fig. 2 Output Voltage vs. Shield Distance (Horizontal) 5 VO - Output Voltage (V) VO - Output Voltage (V) Shield moves vertically: VCC = 5 V R L= 1K Ohm TA = 25˚C Black Shield 5 d 0 4 4 Shield Completely Blocks Aperture At 0 mm. RL = 1kΩ, TA = 25˚C 3 3 2 2 1 1 0 0 0 1 2 3 4 5 6 0.0 0.1 0.2 0.3 0.4 0.5 0.6 d-Distance (mm) d-Distance (mm) Fig. 3 Supply Current vs. Supply Voltage 4.0 3.5 4.0 Fig. 4 Supply Current vs. Supply Voltage Optical Path Unblocked Normalized To: VCC = 5 V, RL = 1kΩ TA = 25˚C ICC - Supply Current (Normalized) ICC - Supply Current (Normalized) 3.0 2.5 2.0 1.5 1.0 0.5 0.0 2 Optical Path Blocked Normalized To: VCC = 5 V, RL = 1kΩ TA = 25˚C 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0.0 4 6 8 10 12 14 16 18 2 4 6 8 10 12 14 16 18 VCC - Supply Voltage (V) VCC - Supply Voltage (V) Fig. 5 Low Level Output Voltage vs. Supply Voltage 0.18 Fig. 6 Low Level Output Voltage vs. Load Resistance VOL - Low Level Output Voltage (V) 0.25 VOL - Low Level Output Voltage (V) Optical Path Blocked RL = 1kΩ, TA = 25˚C 0.16 0.14 0.12 0.10 0.08 0.06 0.04 0.02 0.00 Optical Path Blocked TA = 25˚C 0.20 0.15 0.10 2 4 6 8 10 12 14 16 18 0 5 10 15 20 25 VCC - Supply Voltage (V) RL - Load Resistance (KΩ) © 2004 Fairchild Semiconductor Corporation Page 3 of 5 6/10/04 OPTOLOGIC® OPTICAL INTERRUPTER SWITCH QVE00112 Fig. 7 Schematic Vcc GrayWire VOLTAGE REGULATOR 240Ω LA Vout White Wire GND Green Wire Fig. 8 Switching Test Curve for Inverters Input Signal 50% 0 mA t PHL t PLH VOH 10% 90% Output Signal 50% 90% VOL 10% 50% tf tr © 2004 Fairchild Semiconductor Corporation Page 4 of 5 6/10/04 OPTOLOGIC® OPTICAL INTERRUPTER SWITCH QVE00112 DISCLAIMER FAIRCHILD SEMICONDUCTOR RESERVES THE RIGHT TO MAKE CHANGES WITHOUT FURTHER NOTICE TO ANY PRODUCTS HEREIN TO IMPROVE RELIABILITY, FUNCTION OR DESIGN. FAIRCHILD DOES NOT ASSUME ANY LIABILITY ARISING OUT OF THE APPLICATION OR USE OF ANY PRODUCT OR CIRCUIT DESCRIBED HEREIN; NEITHER DOES IT CONVEY ANY LICENSE UNDER ITS PATENT RIGHTS, NOR THE RIGHTS OF OTHERS. LIFE SUPPORT POLICY FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury of the user. 2. A critical component in any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. © 2004 Fairchild Semiconductor Corporation Page 5 of 5 6/10/04