GP10D

GP10A THRU GP10Y GLASS PASSIVATED JUNCTION RECTIFIER Reverse Voltage - 50 to 1600 Volts * D DO-204AL Forward Current - 1.0 Ampere FEATURES ♦ Plastic package has Underwriters Laboratory Flammability Classification 94V-0 ♦ High temperature metallurgically bonded construction ♦ Glass passivated cavity-free junction ♦ Capable of meeting environmental standards of MIL-S-19500 ♦ 1.0 Ampere operation at TA=75°C and 55°C with no thermal runaway ♦ Typical IR less than 0.1µA ♦ High temperature soldering guaranteed: 350°C/10 seconds, 0.375" (9.5mm) lead length, 5 lbs. (2.3kg) tension N T E P A T 1.0 (25.4) MIN. 0.107 (2.7) 0.080 (2.0) DIA. E 0.205 (5.2) 0.160 (4.1) 1.0 (25.4) MIN. 0.034 (0.86) 0.028 (0.71) DIA. NOTE: Lead diameter is 0.026 (0.66) 0.023 (0.58) for suffix "E" part numbers *Glass-plastic encapsulation is covered by Patent No. 3,996,602 and brazed-lead assembly by Patent No. 3,930,306 Dimensions in inches and (millimeters) MECHANICAL DATA Case: JEDEC DO-204AL molded plastic over glass body Terminals: Plated axial leads, solderable per MIL-STD-750, Method 2026 Polarity: Color band denotes cathode end Mounting Position: Any Weight: 0.012 ounce, 0.3 gram ® MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS A B D G J K M N Q T V W Y UNITS Maximum repetitive peak reverse voltage Maximum average forward rectified current 0.375" (9.5mm) lead length (SEE FIG. 1) Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) Maximum instantaneous forward voltage at 1.0A Maximum full load reverse current, full cycle average, 0.375" (9.5mm) lead lengths at TA=75°C Maximum DC reverse current at rated DC blocking voltage Typical reverse recovery time (NOTE 1) Typical junction capacitance (NOTE 2) Typical thermal resistance (NOTE 3) Operating junction and storage temperature range TA=25°C TA=125°C VRRM I(AV) 50 to 1600 Volts (SEE FIG. 5) 1.0 Volts Amp IFSM VF IR(AV) IR trr CJ RΘJA TJ, TSTG 30.0 1.1 1.2 30.0 5.0 50.0 2.0 8.0 -65 to +175 7.0 55.0 25.0 1.3 Amps Volts µA µA µs 5.0 pF °C/W °C -65 to +150 NOTES: (1) Reverse recovery test condition: IF=0.5A, IR=1.0A, Irr=0.25A (2) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts (3) Thermal resistance from junction to ambient at 0.375" (9.5mm) lead lengths, P.C.B. mounted 4/98 RATINGS AND CHARACTERISTIC CURVES GP10A THRU GP10Y FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT AVERAGE FORWARD RECTIFIED CURRENT, AMPERES PEAK FORWARD SURGE CURRENT, AMPERES FIG. 1 - FORWARD CURRENT DERATING CURVE 30 1.0 GP10A - GP10M TJ=TJ max. 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) 0.8 0.6 0.4 0.2 25 GP10N - GP10Y 60 HZ RESISTIVE OR INDUCTIVE LOAD 20 GP10A - GP10M 15 GP10N - GP10Y 0.375" (9.5mm) LEAD LENGTH 0 20 40 60 80 100 120 140 160 180 10 AMBIENT TEMPERATURE, °C 5.0 1 10 NUMBER OF CYCLES AT 60 HZ 100 FIG. 3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS FIG. 4 - TYPICAL REVERSE CHARACTERISTICS 20 INSTANTANEOUS FORWARD CURRENT, AMPERES 10 INSTANTANEOUS REVERSE LEAKAGE CURRENT, MICROAMPERES 10 TJ=125°C 1 TJ=75°C 1 TJ=25°C PULSE WIDTH=300µs 1% DUTY CYCLE 0.1 0.1 0.01 TJ=25°C GP10A to GP10J GP10K to GP10Q GP10T to GP10Y 0.01 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 1.4 1.5 1.6 0.001 0 20 40 60 80 100 INSTANTANEOUS FORWARD VOLTAGE, VOLTS PERCENT OF RATED PEAK REVERSE VOLTAGE, % FIG. 5 - MAXIMUM REPETITIVE PEAK REVERSE VOLTAGE, VRRM GP10A GP10B GP10D GP10G GP10J GP10K GP10M GP10N GP10Q GP10T GP10V GP10W GP10Y . . . . . . .50V . . . . . .100V . . . . . .200V . . . . . .400V . . . . . .600V . . . . . .800V . . . . .1000V . . . . .1100V . . . . .1200V . . . . .1300V . . . . .1400V . . . .1500V . . . . .1600V JUNCTION CAPACITANCE pF FIG. 6 - TYPICAL JUNCTION CAPACITANCE 20 10 TJ=25°C f=1.0 MHZ Vsig=50mVp-p GP10A to GP10J GP10K to GP10Q GP10T to GP10Y 1.0 0.1 1 10 100 REVERSE VOLTAGE, VOLTS