3080

General Purpose Industrial VRS Magnetic Speed Sensors DESCRIPTION General Purpose VRS sensors are designed for use in applications with medium to high speeds or in electrically noisy environments with relatively small air gaps. The output signal of a VRS sensor is an ac voltage that varies in amplitude and wave frequency as the speed of the monitored device changes, and is usually expressed in peak to peak voltage (Vp-p). Passive VRS (Variable Reluctance Speed) Magnetic Speed sensors are simple, rugged devices that do not require an external voltage source for operation. One complete waveform (cycle) occurs as each target passes the sensor’s pole piece. If a standard gear were used as a target, this output signal would resemble a sine wave if viewed on an oscilloscope. A permanent magnet in the sensor establishes a fixed magnetic field. The approach and passing of a ferrous metal target near the sensor’s pole piece (sensing area) changes the flux of the magnetic field, dynamically changing its strength. This change in magnetic field strength induces a current into a coil winding which is attached to the output terminals. FEATURES • Self-powered operation • Direct conversion of actuator speed to output frequency • Simple installation • No moving parts • Designed for use over a wide range of speeds • Adaptable to a wide variety of configurations • Customized VRS products for unique speed sensing applications • Housing diameters: 5/8 in (M16), 3/8 in (M12) mm, 1/4 in (M8), 10/32 in • Housing materials/styles: stainless steel threaded or smooth • Terminations: MS3106 connector, preleaded • Output voltages: 8 Vp-p to 40 Vp-p Honeywell also offers VRS sensors for high output, power output, high resolution, high temperature and hazardous location applications, as well as low-cost molded versions. POTENTIAL APPLICATIONS • Engine RPM (revolutions per minute) measurement on aircraft, automobiles, boats, buses, trucks and rail vehicles • Motor RPM measurement on drills, grinders, lathes and automatic screw machines • Motor RPM measurement on precision camera, tape recording and motion picture equipment • Process speed measurement on food, textile, paper, woodworking, printing, tobacco and pharmaceutical industry machinery • Motor speed measurement of electrical generating equipment • Speed measurement of pumps, blowers, mixers, exhaust and ventilating fans • Flow measurement on turbine meters • Wheel-slip measurement on autos and locomotives • Gear speed measurement General Purpose 5/8 INCH (M16*) SENSORS (All dimensions for reference only. mm/[in]) *Contact Honeywell for availability of metric mounting thread versions. General Specifications Test Condition Specifications Parameter Characteristic Min. output voltage 40 Vp-p Parameter Inductance Characteristic 25 mH max. Coil resistance 45 Ohm to 85 Ohm Gear pitch range Pole piece diameter Min. surface speed 2,69 mm [0.106 in] Optimum actuator 0,50 m/s [20 in/s] typ. Max. operating frequency 24 DP (module 1.06) or coarser 20 DP (module 1.27) ferrous metal gear 50 kHz typ. Operating temp. range Mounting thread -55 ºC to 120 ºC [-67 ºF to 250 ºF] 5/8-18 UNF-2A Vibration Catalog Listing 3010AN 3010AN25 3010AN30 3010AN40 3010AN50 Thread Length (A) 28 mm [1.1 in] 63 mm [2.5 in] 76 mm [3.0 in] 101 mm [4.0 in] 127 mm [5.0 in] Weight Catalog Listing Thread Length (A) Weight 3010A 3010A25 35 mm [1.4 in] 63 mm [2.5 in] 70 g [2.5 oz] 84 g [3.0 oz] 2 70 g [2.5 oz] 84 g [3.0 oz] 84 g [3.0 oz] 98 g [3.5 oz] 128 g [4.5 oz] www.honeywell.com/sensing Termination Mil-Std 202F Method 204D MS3106 connector Parameter Characteristic Surface speed 25 m/s [1000 in/s] Gear 20 DP (module 1.27) Air gap 0,127 mm [0.005 in] Load 100 kOhm resistance Industrial VRS Magnetic Speed Sensors 5/8 INCH (M16*) SENSORS CONTINUED (All dimensions for reference only. mm/[in]) *Contact Honeywell for availability of metric mounting thread versions. General Specifications Test Condition Specifications Parameter Characteristic Min. output voltage 40 Vp-p Parameter Inductance Characteristic 25 mH max. Coil resistance 45 Ohm to 85 Ohm Gear pitch range Pole piece diameter Min. surface speed 2,69 mm [0.106 in] Optimum actuator 0,50 m/s [20 in/s] typ. Max. operating frequency 24 DP (module 1.06) or coarser 20 DP (module 1.27) ferrous metal gear 50 kHz typ. Operating temp. range Mounting thread -55 ºC to 120 ºC [-67 ºF to 250 ºF] 5/8-18 UNF-2A Vibration Catalog Listing 3010H20 140 g [5.0 oz] Catalog Listing 3010S20 3010S30 Thread Length (A) 50 mm [2.0 in] 76 mm [3.0 in] Termination Parameter Characteristic Surface speed 25 m/s [1000 in/s] Gear 20 DP (module 1.27) Air gap 0,127 mm [0.005 in] Load 100 kOhm resistance Mil-Std 202F Method 204D 20 AWG Tefloninsulated leads Weight Weight 70 g [2.5 oz] 84 g [3.0 oz] Honeywell Sensing and Control 3 General Purpose 3/8 INCH (M12*) SENSORS *Contact Honeywell for availability of metric mounting thread versions. General Specifications Parameter Min. output voltage Coil resistance 4 Test Condition Specifications Characteristic 20 Vp-p Parameter Inductance Characteristic 15 mH max. 45 Ohm to 65 Ohm Gear pitch range Pole piece diameter Min. surface speed 2,36 mm [0.093 in] Optimum actuator 0,50 m/s [20 in/s] typ. Max. operating frequency 26 DP (module 0.98) or coarser 24 DP (module 1.06) ferrous metal gear 50 kHz typ. Operating temp. range Mounting thread -40 ºC to 107 ºC [-40 ºF to 225 ºF] 3/8-24 UNF-2A Vibration Catalog Listing 3015A 3015A17 3015A35 Thread Length (A) 20 mm [0.8 in] 44 mm [1.7 in] 88 mm [3.5 in] Catalog Listing 3015S13 Weight Catalog Listing 3015SS13 3015SS25 Thread Length (A) 30 mm [1.2 in] 63 mm [2.5 in] Weight 28 g [1.0 oz] 35 g [1.2 oz] 42 g [1.5 oz] 28 g [1.0 oz] Weight 28 g [1.0 oz] 42 g [152 oz] www.honeywell.com/sensing Termination Mil-Std 202F Method 204D 24 AWG vinyl-insulated leads Parameter Characteristic Surface speed 25 m/s [1000 in/s] Gear 20 DP (module 1.27) Air gap 0,127 mm [0.005 in] Load 100 kOhm resistance Industrial VRS Magnetic Speed Sensors 1/4 INCH (M8*) SENSORS (All dimensions for reference only. mm/[in]) *Contact Honeywell for availability of metric mounting thread versions. General Specifications Parameter Min. output voltage Coil resistance Test Condition Specifications Characteristic 12 Vp-p Parameter Inductance Characteristic 16 mH max. 190 Ohm max. Gear pitch range Pole piece diameter Min. surface speed 1,00 mm [0.040 in] Optimum actuator 0,75 m/s [30 in/s] typ. Max. operating frequency 36 DP (module 0.70) or coarser 28 DP (module 0.90) ferrous metal gear 60 kHz typ. Operating temp. range Mounting thread -40 ºC to 107 ºC [-40 ºF to 225 ºF] 1/4-40 UNS-2A Vibration Catalog Listing 3050 3050A13 3050A20 Thread Length (A) 15 mm [0.6 in] 30 mm [1.2 in] 50 mm [2.0 in] Parameter Min. output voltage Coil resistance Termination Mil-Std 202F Method 204D 30 AWG vinyl-insulated leads Weight 14 g [0.5 oz] 14 g [0.5 oz] 14 g [0.5 oz] Characteristic 12 Vp-p Parameter Inductance Characteristic 16 mH max. 190 Ohm max. Gear pitch range Pole piece diameter Min. surface speed 1,00 mm [0.040 in] Optimum actuator 0,75 m/s [30 in/s] typ. Max. operating frequency 36 DP (module 0.70) or coarser 28 DP (module 0.90) ferrous metal gear 60 kHz typ. Operating temp. range Mounting thread -40 ºC to 107 ºC [-40 ºF to 225 ºF] 1/4-40 UNS-2A Vibration Catalog Listing 3050S10 Thread Length 25 mm [1.0 in] Parameter Characteristic Surface speed 25 m/s [1000 in/s] Gear 20 DP (module 1.27) Air gap 0,127 mm [0.005 in] Load 100 kOhm resistance Termination Parameter Characteristic Surface speed 25 m/s [1000 in/s] Gear 20 DP (module 1.27) Air gap 0,127 mm [0.005 in] Load 100 kOhm resistance Mil-Std 202F Method 204D 30 AWG PVC-insulated leads Weight 14 g [0.5 oz] Honeywell Sensing and Control 5 General Purpose 10/32 INCH SENSORS (All dimensions for reference only. mm/[in]) (No metric available.) General Specifications Parameter Min. output voltage Coil resistance Characteristic 8 Vp-p Parameter Inductance Characteristic 14 mH max. 155 Ohm Gear pitch range Pole piece diameter Min. surface speed 1,5 mm [0.062 in] Optimum actuator 0,75 m/s [30 in/s] typ. Max. operating frequency 32 DP (module 0.80) or coarser 26 DP (module 0.98) ferrous metal gear 60 kHz (typ.) Operating temp. range -40 ºC to 107 ºC [-40 ºF to 225 ºF] Vibration Mil-Std 202F Method 204D Mounting thread 10-32 UNF-2A Termination 32 AWG Tefloninsulated leads Catalog Listing 3080 6 Test Condition Specifications Thread Length 12 mm [0.5 in] Weight 8,5 g [0.3 oz] www.honeywell.com/sensing Parameter Characteristic Surface speed 25 m/s [1000 in/s] Gear 20 DP (module 1.27) Air gap 0,127 mm [0.005 in] Load 100 kOhm resistance Industrial VRS Magnetic Speed Sensors THIS PAGE INTENTIONALLY LEFT BLANK. Honeywell Sensing and Control 7 WARNING WARNING PERSONAL INJURY MISUSE OF DOCUMENTATION DO NOT USE these products as safety or emergency stop • devices or in any other application where failure of the The information presented in this product sheet is for reference only. Do not use this document as a product product could result in personal injury. installation guide. Failure to comply with these instructions could result in death or serious injury. • Complete installation, operation, and maintenance information is provided in the instructions supplied with each product. Failure to comply with these instructions could result in WARRANTY/REMEDY Honeywell warrants goods of its manufacture as being free of death or serious injury. defective materials and faulty workmanship. Honeywell’s SALES AND SERVICE standard product warranty applies unless agreed to otherwise Honeywell serves its customers through a worldwide network by Honeywell in writing; please refer to your order of sales offices, representatives and distributors. For acknowledgement or consult your local sales office for specific application assistance, current specifications, pricing or name warranty details. If warranted goods are returned to Honeywell of the nearest Authorized Distributor, contact your local sales during the period of coverage, Honeywell will repair or replace, office or: at its option, without charge those items it finds defective. The foregoing is buyer’s sole remedy and is in lieu of all other E-mail: info.sc@honeywell.com warranties, expressed or implied, including those of merchantability and fitness for a particular purpose. In no event shall Honeywell be liable for consequential, special, or indirect damages. Internet: www.honeywell.com/sensing Phone and Fax: Asia Pacific +65 6355-2828 Europe +44 (0) 1698 481481 +65 6445-3033 Fax While we provide application assistance personally, through our literature and the Honeywell web site, it is up to the customer to determine the suitability of the product in the +44 (0) 1698 481676 Fax application. Latin America +1-305-805-8188 Specifications may change without notice. The information we USA/Canada +1-800-537-6945 +1-305-883-8257 Fax supply is believed to be accurate and reliable as of this +1-815-235-6847 printing. However, we assume no responsibility for its use. +1-815-235-6545 Fax Automation and Control Solutions Sensing and Control Honeywell 1985 Douglas Drive North Minneapolis, MN 55422 www.honeywell.com/sensing 005875-2-EN IL50 GLO Printed in USA November 2007 Copyright © 2007 Honeywell International Inc. All rights reserved.