CA5160E

CA5160 NOT RECOMMENDED FOR NEW DESIGNS September 1998 4MHz, BiMOS Microprocessor Operational Amplifiers with MOSFET Input/CMOS Output Description CA5160 is an integrated circuit operational amplifier that combines the advantage of both CMOS and bipolar transistors on a monolithic chip. The CA5160 is a frequency compensated version of the popular CA5130 series. It is designed and guaranteed to operate in microprocessor or logic systems that use +5V supplies. Gate-protected P-Channel MOSFET (PMOS) transistors are used in the input circuit to provide very high input impedance, very low input current, and exceptional speed performance. The use of PMOS field effect transistors in the input stage results in common-mode input voltage capability down to 0.5V below the negative supply terminal, an important attribute in single supply applications. A complementary symmetry MOS (CMOS) transistor pair, capable of swinging the output voltage to within 10mV of either supply voltage terminal (at very high values of load impedance), is employed as the output circuit. The CA5160 operates at supply voltages ranging from +5V to +16V, or ±2.5V to ±8V when using split supplies, and have terminals for adjustment of offset voltage for applications requiring offset-null capability. Terminal provisions are also made to permit strobing of the output stage. It has guaranteed specifications for 5V operation over the full military temperature range of -55oC to 125oC. Features • MOSFET Input Stage - Very High ZI; 1.5TΩ (1.5 x 1012Ω) (Typ) - Very Low II; 5pA (Typ) at 15V Operation 2pA (Typ) at 5V Operation • Common-Mode Input Voltage Range Includes Negative Supply Rail; Input Terminals Can be Swung 0.5V Below Negative Supply Rail • CMOS Output Stage Permits Signal Swing to Either (or Both) Supply Rails • CA5160 Has Full Military Temperature Range Guaranteed Specifications for V+ = 5V • CA5160 is Guaranteed to Operate Down to 4.5V for AOL • CA5160 is Guaranteed Up to ±7.5V Applications • Ground Referenced Single Supply Amplifiers • Fast Sample-Hold Amplifiers • Long Duration Timers/Monostables • Ideal Interface With Digital CMOS • High Input Impedance Wideband Amplifiers • Voltage Followers (e.g., Follower for Single Supply D/A Converter) • Wien-Bridge Oscillators • Voltage Controlled Oscillators • Photo Diode Sensor Amplifiers • 5V Logic Systems • Microprocessor Interface Ordering Information PART NUMBER (BRAND) CA5160E CA5160M96 (5160) TEMP. RANGE (oC) -55 to 125 -55 to 125 PACKAGE 8 Ld PDIP 8 Ld SOIC Tape and Reel PKG. NO. E8.3 M8.15 Pinout CA5160 (PDIP, SOIC) TOP VIEW OFFSET NULL INV. INPUT NON INV. INPUT V- 1 2 3 4 8 7 6 5 STROBE V+ OUTPUT OFFSET NULL + NOTE: CA5160 devices have an on-chip frequency compensation network. Supplementary phase-compensation or frequency roll-off (if desired) can be connected externally between terminals 1 and 8. CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Copyright © Intersil Corporation 1999 File Number 1924.4 3-1 CA5160 Absolute Maximum Ratings Supply Voltage (V+ to V-) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16V Differential Input Voltage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8V DC Input Voltage . . . . . . . . . . . . . . . . . . . . . . (V+ +8V) to (V- -0.5V) Input Current. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1mA Output Short Circuit Duration (Note 2) . . . . . . . . . . . . . . . . Indefinite Thermal Information Thermal Resistance (Typical, Note 1) θJA (oC/W) θJC (oC/W) PDIP Package . . . . . . . . . . . . . . . . . . . 120 N/A SOIC Package . . . . . . . . . . . . . . . . . . . 165 N/A Maximum Junction Temperature (Plastic Package) . . . . . . . . 150oC Maximum Storage Temperature Range . . . . . . . . . -65oC to 150oC Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . 300oC (SOIC - Lead Tips Only) Operating Conditions Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . -55oC to 125oC CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. NOTES: 1. θJA is measured with the component mounted on an evaluation PC board in free air. 2. Short circuit may be applied to ground or to either supply. Electrical Specifications TA = 25oC, V+ = 5V, V- = 0V, Unless Otherwise Specified TEST CONDITIONS VO = 2.5V VO = 2.5V VO = 2.5V VCM = 0 to 1V VCM = 0 to 2.5V CA5160 MIN 70 60 2.5 ∆V+ = 1V; ∆V- = 1V RL= ∞ RL=10kΩ ISOURCE ISINK VOUT VO = 0V VO = 5V RL = ∞ 55 95 85 1.0 1.0 4.99 RL = 10kΩ 4.4 RL = 2kΩ 2.5 ISUPPLY ISUPPLY VO = 0V VO = 2.5V TYP 2 0.1 2 80 69 2.8 -0.5 67 117 102 3.4 2.2 5 0 4.7 0 3.3 0 50 320 MAX 10 10 15 0 4.0 4.0 0.01 0.01 0.01 100 400 UNITS mV pA pA dB dB V V dB dB dB mA mA V V V V V V µA µA PARAMETER Input Offset Voltage Input Offset Current Input Current Common Mode Rejection Ratio SYMBOL VIO IIO II CMRR Common Mode Input Voltage Range VlCR+ VlCR- Power Supply Rejection Ratio Large Signal Voltage Gain (Note 3) Source Current Sink Current Maximum Output Voltage VOM+ VOMVOM+ VOMVOM+ VOMSupply Current VO = 0.1 to 4.1V VO = 0.1 to 3.6V PSRR AOL NOTE: 3. For V+ = 4.5V and V- = GND; VOUT = 0.5V to 3.2V at RL = 10kΩ. Electrical Specifications TA = -55oC to 125oC, V+ = 5V, V- = 0V, Unless Otherwise Specified TEST CONDITIONS VO = 2.5V VO = 2.5 V CA5160 MIN TYP 3 0.1 MAX 15 10 UNITS mV nA PARAMETER Input Offset Voltage Input Offset Current SYMBOL VIO IIO 3-2 CA5160 Electrical Specifications TA = -55oC to 125oC, V+ = 5V, V- = 0V, Unless Otherwise Specified (Continued) TEST CONDITIONS VO = 2.5V VCM = 0 to 1V VCM = 0 to 2.5V Common Mode Input Voltage Range VlCR+ VlCRPower Supply Rejection Ratio Large Signal Voltage Gain (Note 4) Source Current Sink Current Maximum Output Voltage VOM+ VOMVOM+ VOMVOM+ VOMSupply Current VO = 0V VO = 2.5V NOTE: 4. For V+ = 4.5V and V- = GND; VOUT = 0.5V to 3.2V at RL = 10kΩ. ISUPPLY ISUPPLY RL = 2kΩ RL = 10kΩ VO = 0.1 to 4.1V VO = 0.1 to 3.6V ISOURCE ISINK VOUT PSRR AOL ∆V+ = 2V RL= ∞ RL=10kΩ VO = 0V VO = 5V RL= ∞ CA5160 MIN 60 50 2.5 40 90 75 0.6 0.6 4.99 4.0 2.0 TYP 2 80 75 2.8 -0.5 60 110 100 5 0 4.3 0 2.5 0 170 410 MAX 15 0 5.0 5.0 0.01 0.01 0.01 220 500 UNITS nA dB dB V V dB dB dB mA mA V V V V V V µA µA PARAMETER Input Current Common Mode Rejection Ratio SYMBOL II CMRR Electrical Specifications TA = 25oC, V+ = 15V, V- = 0V, Unless Otherwise Specified TEST CONDITIONS VS = ±7.5V VS = ±7.5V VS = ±7.5V VO = 10VP-P RL = 2kΩ CA5160 MIN 50 94 70 10 ∆V+ = 1V; ∆V- = 1V VS = ±7.5V RL = 2kΩ 12 RL = ∞ 14.99 TYP 6 0.5 5 320 110 90 -0.5 to 12 32 13.3 0.002 15 0 MAX 15 30 50 0 320 0.01 0.1 UNITS mV pA pA kV/V dB dB V µV/V V V V V PARAMETER Input Offset Voltage Input Offset Current Input Current Large Signal Voltage Gain SYMBOL VIO IIO II AOL Common Mode Rejection Ratio Common Mode Input Voltage Range Power Supply Rejection Ratio Maximum Output Voltage VOM+ VOMVOM+ VOM- CMRR VlCR PSRR VOUT 3-3 CA5160 Electrical Specifications TA = 25oC, V+ = 15V, V- = 0V, Unless Otherwise Specified (Continued) TEST CONDITIONS VO = 0V VO = 15V I+ RL = ∞, VO = 7.5V RL = ∞, VO = 0V Input Offset Voltage Temperature Drift ∆VIO/∆T CA5160 MIN 12 12 TYP 22 20 10 2 8 MAX 45 45 15 3 UNITS mA mA mA mA µV/oC PARAMETER Maximum Output Current Supply Current IOM+ (Source) IOM- (Sink) SYMBOL IO Electrical Specifications For Design Guidance, At TA = 25oC, VSUPPLY = ±7.5V, Unless Otherwise Specified TYPICAL VALUES PARAMETER Input Offset Voltage Adjustment Range Input Resistance Input Capacitance Equivalent Input Noise Voltage SYMBOL TEST CONDITIONS 10kΩ Across Terminals 4 and 5 or 4 and 1 CA5160 ±22 1.5 UNITS mV TΩ pF µV µV nV/√Hz nV/√Hz MHz V/µs µs % µs RI CI eN f = 1MHz BW = 0.2MHz, RS = 1MΩ BW = 0.2MHz, RS = 10MΩ 4.3 40 50 72 30 4 10 Equivalent Input Noise Voltage eN RS = 100Ω, 1kHz RS = 100Ω, 10kHz Unity Gain Crossover Frequency Slew Rate Transient Response Rise Time Overshoot Settling Time (To