KP-1608QBC-D

1.6X0.8mm SMD CHIP LED LAMP Part Number: KP-1608QBC-D Blue ATTENTION OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Features Descriptions 1.6mmX0.8mm SMD LED, 1.1mm thickness. The Blue source color devices are made with InGaN Low power consumption. Light Emitting Diode. Wide viewing angle. Electrostatic discharge and power surge could damage Ideal for backlight and indicator. the LEDs. Package: 2000pcs / reel. It is recommended to use a wrist band or anti- Moisture sensitivity level : level 3. electrostatic glove when handling the LEDs. All devices, equipments and machineries must be RoHS compliant. electrically grounded. Package Dimensions K g in ig r b t h Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.1(0.004") unless otherwise noted. 3.The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 4.The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAA8751 REV NO: V.19B DATE: MAY/10/2016 PAGE: 1 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: M.Liu ERP: 1203000050 Selection Guide Part No. Emitting Color (Material) Viewing Angle [1] Iv (mcd) [2] @ 20mA Lens Type Min. KP-1608QBC-D Blue (InGaN) Typ. 2θ1/2 40 100 130° Water Clear Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity / luminous Flux: +/-15%. 3. Luminous intensity value is traceable to CIE127-2007 standards. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Emitting Color Typ. λpeak Peak Wavelength Blue Dominant Wavelength Blue Δλ1/2 Spectral Line Half-width Blue C Capacitance Blue VF [2] Forward Voltage IR Reverse Current t h 460 λD [1] Blue Units Test Conditions nm IF=20mA nm IF=20mA nm IF=20mA pF VF=0V;f=1MHz 4 V IF=20mA 50 uA VR=5V ig r b g in Blue Max. 465 25 100 3.3 Notes: 1. Wavelength: +/-1nm. 2. Forward Voltage: +/-0.1V. 3. Wavelength value is traceable to CIE127-2007 standards. 4. Excess driving current and / or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. K Absolute Maximum Ratings at TA=25°C Parameter Values Units Power dissipation 120 mW DC Forward Current 30 mA Peak Forward Current [1] 150 mA Electrostatic Discharge Threshold (HBM) 250 V 5 V Reverse Voltage Operating Temperature -40°C To +85°C Storage Temperature -40°C To +85°C Notes: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. 2. Relative humidity levels maintained between 40% and 60% in production area are recommended to avoid the build-up of static electricity – Ref JEDEC/JESD625-A and JEDEC/J-STD-033. SPEC NO: DSAA8751 REV NO: V.19B DATE: MAY/10/2016 PAGE: 2 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: M.Liu ERP: 1203000050 Blue KP-1608QBC-D t h ig r b g in K SPEC NO: DSAA8751 REV NO: V.19B DATE: MAY/10/2016 PAGE: 3 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: M.Liu ERP: 1203000050 KP-1608QBC-D Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Tape Dimensions (Units : mm) K g in ig r b t h Reel Dimension SPEC NO: DSAA8751 REV NO: V.19B DATE: MAY/10/2016 PAGE: 4 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: M.Liu ERP: 1203000050 PACKING & LABEL SPECIFICATIONS KP-1608QBC-D t h ig r b g in K Terms and conditions for the usage of this document 1. The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6. All design applications should refer to Kingbright application notes available at http://www.kingbright.com/application_notes SPEC NO: DSAA8751 REV NO: V.19B DATE: MAY/10/2016 PAGE: 5 OF 5 APPROVED: Wynec CHECKED: Allen Liu DRAWN: M.Liu ERP: 1203000050