A1220UA4LXX

SIDACtor ® Protection Thyristors LCAS Protection Asymmetrical Multiport Series - MS-013 Description Asymmetrical Multiport Series are SIDACtor® devices designed to protect LCAS (Line Circuit Access Switch) devices from damaging overvoltage transients. The series provides a specialized asymmetrical dual port overvoltage protection solution that enables equipment to comply with various global requlatory standards. Features and Benefits Low voltage overshoot Low on-state voltage Agency Approvals Agency Agency File Number E133083 Replaces four discrete devices Two-port protection LCAS specific tip and ring thresholds Does not degrade with use Fails short circuit when surged in excess of ratings Pinout Designation 1 2 3 6 5 4 Applicable Global Standards TIA-968-A TIA-968-B ITU K.20/21 Enhanced Level* ITU K.20/21 Basic Level GR 1089 Inter-building* 6 (T2) 5 (G2) 4 (R2) *A-rated parts require series resistance GR 1089 Intra-building IEC 61000-4-5 YD/T 1082 YD/T 993 YD/T 950 Schematic Symbol (T1) 1 (G1) 2 (R1) 3 Electrical Characteristics VDRM @IDRM VS VDRM @IDRM = 5μA @100V/μs = 5μA Part Marking V A1220UA4 A1250UA4 A1220UC4 A1250UC4 100 100 100 100 V 130 130 130 130 V 180 230 180 230 V 220 290 220 290 V Pins 1-2, 2-3, 4-5, 5-6 4 4 4 4 800 800 800 800 2.2 2.2 2.2 2.2 120 120 120 120 Pins 2-3, 5-6 A1220UA4Lxx A1225UA4Lxx A1220UC4Lxx A1225UC4Lxx Pins 1-2, 4-5 VS @100V/μs Part Number VT@IT = 2.2 Amps IS mA IT A IH mA Notes: - Absolute maximum ratings measured at TA= 25ºC (unless otherwise noted). - Devices are bi-directional. - All electrical characteristics shown are defined from Tip to Ground (pin 1 to pin 2 and pin 6 to pin 5) and Ring to Ground (pin 3 to pin 2 and pin 4 to pin 5). - XX = Part Number Suffix: ‘TP’ (Tube Pack) or ‘RP’ (Reel Pack). © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 130 Revised: February 22, 2011 SIDACtor ® Protection Thyristors LCAS Protection Capacitance Values pF Pin 1-2 / 4-5 Ring-Ground MIN A1220UA4Lxx A1225UA4Lxx A1220UC4Lxx A1225UC4Lxx 15 15 35 35 MAX 25 25 50 50 pF Pin 3-2 / 6-5 Tip-Ground MIN 30 30 60 60 MAX 50 50 90 90 pF Pin 1-3 (4-6) Tip-Ring MIN 5 5 20 20 MAX 20 20 35 35 Part Number Note: Off-state capacitance (CO) is measured at 1 MHz with a 2 V bias. Surge Ratings IPP Series 0.2x310 0.5x700 2 1 2x10 2x10 2 1 8x20 1.2x50 2 1 10x160 10x160 2 1 10x560 1 10x560 2 A min 50 150 5x320 1 9x720 2 A min 75 200 10x360 1 10x360 2 A min 75 175 10x1000 1 10x1000 2 A min 45 100 5x310 1 10x700 2 A min 75 200 ITSM 50/60 Hz A min 20 30 di/dt A/μs max 500 500 A min A C Notes: 1 Current waveform in μs 2 Voltage waveform in μs A min 150 500 A min 150 400 A min 90 200 20 50 - Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product. - IPP - The device must initially be in thermal equilibrium with -40°C < TJ < Thermal Considerations Package Modified MS-013 6 5 4 Symbol TJ TS R0JA Parameter Operating Junction Temperature Range Storage Temperature Range Thermal Resistance: Junction to Ambient Value Unit °C °C 2 3 60 °C/W V-I Characteristics +I tr x td Pulse Waveform IPP – Peak Pulse Current – %IPP IT IS IH IDRM -V VT VDRM VS +V 100 Peak Value tr = r ise time to peak value td = decay time to half value Waveform = tr x td 50 Half Value 0 0 -I tr td t – Time (μs) © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 131 Revised: February 22, 2011 SIDACtor ® Protection Thyristors LCAS Protection Normalized VS Change vs. Junction Temperature Normalized DC Holding Current vs. Case Temperature 2.0 14 Percent of VS Change – % 10 8 6 4 2 0 -4 -6 -8 -40 -20 0 20 40 60 80 100 120 140 160 IH (TC = 25ºC) 12 1.8 1.6 1.4 1.2 1.0 0.8 0.6 0.4 -40 -20 0 20 40 60 80 100 120 140 160 IH 25 °C 25°C Ratio of Case Temperature (TC) - ºC Junction Temperature (TJ) – °C Soldering Parameters Reflow Condition - Temperature Min (Ts(min)) Pb-Free assembly (see Fig. 1) Figure 1 Pre Heat - Temperature Max (Ts(max)) - Time (Min to Max) (ts) TP Ramp-up tP Critical Zone TL to TP 60-180 secs. 3°C/sec. Max. 3°C/sec. Max. 60-150 secs. TS(max) to TL - Ramp-up Rate Reflow - Temperature (TL) (Liquidus) - Temperature (tL) Temperature Average ramp up rate (Liquidus Temp (TL) to peak) TL TS(max) Preheat tL Ramp-down TS(min) tS Peak Temp (TP) Time within 5°C of actual Peak Temp (tp) Ramp-down Rate Time 25°C to Peak Temp (TP) Do not exceed 30 secs. Max. 6°C/sec. Max. 8 min. Max. 25 time to peak temperature (t 25ºC to peak) Time Environmental Specifications High Temp Voltage Blocking 80% Rated VDRM (VAC Peak 504 or 1008 hrs. MIL -STD-750 (Method 1040) JEDEC, JESD22-A-101 cycles. MIL -STD-750 (Method 1051) EIA/JEDEC, JESD22-A104 52 VDC JEDEC, JESD22-A-101 JEDEC, JESD22-A-101 -65°C, 1008 hrs. 10 cycles. MIL -STD-750 (Method 1056) JEDEC, JESD22-A-106 JEDEC, JESD22-A-102 Physical Specifications Lead Material Terminal Finish Body Material Copper Alloy 100% Matte-Tin Plated UL recognized epoxy meeting flammability classification 94V-0 Temp Cycling Biased Temp & Humidity High Temp Storage Low Temp Storage Thermal Shock Autoclave (Pressure Cooker Test) Resistance to Solder Heat Moisture Sensitivity Level Part Numbering A xxxx U x 4 L xx TYPE A: Asymmetrical SIDACtor PACKING OPTIONS RP: Reel Pack TP: Tube Pack RoHS COMPLIANT CONSTRUCTION VARIABLE MEDIAN VOLTAGE PACKAGE TYPE IPP RATING © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 132 Revised: February 22, 2011 SIDACtor ® Protection Thyristors LCAS Protection Part Marking Packing Options Package Type Description Quantity Added Suffix Industry Standard XXXXXXXX XXXXX Part Marking Code (Refer to Electrical Characteristics Table) Date Code Modified MS-013 6-pin Tape and Reel Pack U 1500 RP TP EIA-481-D N/A 500 Modified MS-013 6-pin (50 per Tube Pack tube) Dimensions — MS-013 Dimensions Pad Outline C 0.138 (3.50) E 0.059 (1.50) 0.065 (1.65) 0.460 (11.68) Dimension are in inches (and millimeters). Inches Min 0.360 0.352 0.400 0.043 0.047 0.293 0.289 0.089 0.041 0.020 0.133 Max 0.364 0.356 0.412 0.045 0.055 0.297 0.293 0.093 0.049 0.143 Millimeters Min 9.14 8.94 10.16 1.09 1.19 7 .44 7 .34 2.26 1.04 0.51 3.38 Max 9.25 9.04 10.46 1.13 1.40 7 .54 7 .44 2.36 1.24 3.63 7º TYP A D 7º TYP G A J H Burr Side 96º 4º 7º TYP B A F 7º TYP MIN Length of Flat K Detail A Mold Split Line BSC* A B C D E F G H J K BSC* * BSC = Basic Spacing between Centers Tape and Reel Specification — MS-013 .157 (4.0) .630 (16.0) .512 (13.0) Arbor Hole Dia. .472 (12.0) 12.99 (330) Dimensions are in inches (and millimeters) 0.700 (17.8) Direction of Feed Tube Pack Specification — MS-013 Message Location .020 ± .005 WALL TYP. (0.51 ± 0.13) .108 (2.74) .110 (2.79) .045 (1.14) 90˚ .165 (4.19) .310 (7.87) 6 Interior of the Tube 20.000 ± .030 (508.00 ± 0.76) .005 A .150 (3.81) .225 (5.72) .525 (13.34) A Dimensions are in inches (and millimeters) © 2011 Littelfuse, Inc. Specifications are subject to change without notice. Please refer to www.littelfuse.com for current information. 133 Revised: February 22, 2011