0
登录后你可以
  • 下载海量资料
  • 学习在线课程
  • 观看技术视频
  • 写文章/发帖/加入社区
创作中心
发布
  • 发文章

  • 发资料

  • 发帖

  • 提问

  • 发视频

创作活动
KSZ8051MNL

KSZ8051MNL

  • 厂商:

    MICREL

  • 封装:

  • 描述:

    KSZ8051MNL - 10Base-T/100Base-TX Physical Layer Transceiver - Micrel Semiconductor

  • 数据手册
  • 价格&库存
KSZ8051MNL 数据手册
KSZ8051MNL/RNL 10Base-T/100Base-TX Physical Layer Transceiver General Description Features The KSZ8051 is a single supply 10Base-T/100Base-TX • Single-chip 10Base-T/100Base-TX IEEE 802.3 Ethernet physical layer transceiver for transmission and compliant Ethernet Transceiver reception of data over standard CAT-5 unshielded twisted • MII Interface support (KSZ8051MNL) pair (UTP) cable. • RMII v1.2 Interface support with 50MHz reference clock The KSZ8051 is a highly integrated, compact solution. It output to MAC, and option to input 50MHz reference reduces board cost and simplifies board layout by using clock (KSZ8051RNL) on-chip termination resistors for the differential pairs and • Back-to-Back mode support for 100Mbps copper by integrating a low noise regulator to supply the 1.2V repeater or media converter core. • MDC/MDIO Management Interface for PHY register The KSZ8051MNL offers the Media Independent Interface configuration (MII) and the KSZ8051RNL offers the Reduced Media • Programmable interrupt output Independent Interface (RMII) for direct connection with MII/ • LED outputs for link, activity and speed status indication RMII compliant Ethernet MAC processors and switches. • On-chip termination resistors for the differential pairs A 25MHz crystal is used to generate all required clocks, including the 50MHz RMII reference clock output for the • Baseline Wander Correction KSZ8051RNL. • HP Auto MDI/MDI-X for reliable detection and The KSZ8051 provides diagnostic features to facilitate correction for straight-through and crossover cables system bring-up and debugging in production testing and with disable and enable option in product deployment. Parametric NAND tree support • Auto-negotiation to automatically select the highest link enables fault detection between KSZ8051 I/Os and board. up speed (10/100 Mbps) and duplex (half/full) ® Micrel LinkMD TDR-based cable diagnostics permit • Power down and power saving modes identification of faulty copper cabling. • LinkMD® TDR-based cable diagnostics for identification The KSZ8051MNL and KSZ8051RNL are available in 32of faulty copper cabling pin, lead-free QFN packages (See Ordering Information). • Parametric NAND Tree support for fault detection Data sheets and support documentation can be found on between chip I/Os and board. Micrel’s web site at: www.micrel.com. ____________________________________________________________________________________________________________ Functional Diagram LinkMD is a registered trademark of Micrel, Inc. Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com July 2010 M9999-070910-1.0 Micrel, Inc. KSZ8051MNL/RNL More Features • Loopback modes for diagnostics • Single 3.3V power supply with VDD I/O options for 1.8V, 2.5V, or 3.3V • Built-in 1.2V regulator for core • Available in 32-pin (5mm x 5mm) QFN package Applications • • • • • • Game Console IP Phone IP Set-top Box IP TV LOM Printer Ordering Information Part Number KSZ8051MNL KSZ8051MNLI KSZ8051RNL KSZ8051RNLI Note: 1. Contact factory for lead time. (1) (1) Temp. Range 0°C to 70°C -40°C to 85°C 0°C to 70°C -40°C to 85°C Package 32-Pin QFN 32-Pin QFN 32-Pin QFN 32-Pin QFN Lead Finish Pb-Free Pb-Free Pb-Free Pb-Free Description MII, Commercial Temperature MII, Industrial Temperature RMII, Commercial Temperature RMII, Industrial Temperature July 2010 2 M9999-070910-1.0 Micrel, Inc. KSZ8051MNL/RNL Revision History Revision 1.0 Date 6/22/10 Summary of Changes Data sheet created. July 2010 3 M9999-070910-1.0 Micrel, Inc. KSZ8051MNL/RNL Contents General Description .............................................................................................................................................................. 1 Features ................................................................................................................................................................................. 1 Functional Diagram............................................................................................................................................................... 1 Applications........................................................................................................................................................................... 2 Ordering Information ............................................................................................................................................................ 2 Revision History.................................................................................................................................................................... 3 Contents................................................................................................................................................................................. 4 List of Figures........................................................................................................................................................................ 7 List of Tables ......................................................................................................................................................................... 8 Pin Configuration – KSZ8051MNL ....................................................................................................................................... 9 Pin Description – KSZ8051MNL......................................................................................................................................... 10 Strapping Options – KSZ8051MNL.................................................................................................................................... 13 Pin Configuration – KSZ8051RNL ..................................................................................................................................... 14 Pin Description – KSZ8051RNL ......................................................................................................................................... 15 Strapping Options – KSZ8051RNL .................................................................................................................................... 18 Functional Description: 10Base-T/100Base-TX Transceiver ......................................................................................... 19 100Base-TX Transmit....................................................................................................................................................... 19 100Base-TX Receive........................................................................................................................................................ 19 10Base-T Transmit ........................................................................................................................................................... 19 10Base-T Receive ............................................................................................................................................................ 19 Scrambler/De-scrambler (100Base-TX only).................................................................................................................... 20 SQE and Jabber Function (10Base-T only)...................................................................................................................... 20 PLL Clock Synthesizer...................................................................................................................................................... 20 Auto-Negotiation ............................................................................................................................................................... 20 MII Data Interface (KSZ8051MNL only) ............................................................................................................................. 21 MII Signal Definition.......................................................................................................................................................... 22 Transmit Clock (TXC) ................................................................................................................................................... 22 Transmit Enable (TXEN) .............................................................................................................................................. 22 Transmit Data [3:0] (TXD[3:0]) ..................................................................................................................................... 22 Receive Clock (RXC).................................................................................................................................................... 22 Receive Data Valid (RXDV).......................................................................................................................................... 22 Receive Data[3:0] (RXD[3:0]) ....................................................................................................................................... 23 Receive Error (RXER) .................................................................................................................................................. 23 Carrier Sense (CRS) .................................................................................................................................................... 23 Collision (COL) ............................................................................................................................................................. 23 MII Signal Diagram ........................................................................................................................................................... 23 RMII Data Interface (KSZ8051RNL only) ........................................................................................................................... 24 RMII – 25MHz Clock Mode............................................................................................................................................... 24 RMII – 50MHz Clock Mode............................................................................................................................................... 24 RMII Signal Definition ....................................................................................................................................................... 24 Reference Clock (REF_CLK) ....................................................................................................................................... 24 July 2010 4 M9999-070910-1.0 Micrel, Inc. KSZ8051MNL/RNL Transmit Enable (TXEN) .............................................................................................................................................. 25 Transmit Data [1:0] (TXD[1:0]) ..................................................................................................................................... 25 Carrier Sense/Receive Data Valid (CRS_DV).............................................................................................................. 25 Receive Data [1:0] (RXD[1:0]) ...................................................................................................................................... 25 Receive Error (RXER) .................................................................................................................................................. 25 Collision Detection........................................................................................................................................................ 25 RMII Signal Diagram......................................................................................................................................................... 25 RMII – 25MHz Clock Mode........................................................................................................................................... 26 RMII – 50MHz Clock Mode........................................................................................................................................... 26 Back-to-Back Mode – 100Mbps Copper Repeater / Media Converter............................................................................ 27 MII Back-to-Back Mode (KSZ8051MNL only)................................................................................................................... 27 RMII Back-to-Back Mode (KSZ8051RNL only) ................................................................................................................ 28 MII Management (MIIM) Interface....................................................................................................................................... 28 Interrupt (INTRP) ................................................................................................................................................................. 29 HP Auto MDI/MDI-X ............................................................................................................................................................. 29 Straight Cable ................................................................................................................................................................... 29 Crossover Cable ............................................................................................................................................................... 30 LinkMD® Cable Diagnostics................................................................................................................................................ 30 NAND Tree Support ............................................................................................................................................................ 30 NAND Tree I/O Testing..................................................................................................................................................... 32 Power Management ............................................................................................................................................................ 32 Power Saving Mode.......................................................................................................................................................... 32 Energy Detect Power Down Mode ................................................................................................................................... 32 Power Down Mode ........................................................................................................................................................... 32 Slow Oscillator Mode ........................................................................................................................................................ 32 Reference Circuit for Power and Ground Connections .................................................................................................. 33 Register Map........................................................................................................................................................................ 34 Register Description ........................................................................................................................................................... 34 Register Description (Continued)...................................................................................................................................... 35 Register Description (Continued)...................................................................................................................................... 36 Register Description (Continued)...................................................................................................................................... 37 Register Description (Continued)...................................................................................................................................... 38 Register Description (Continued)...................................................................................................................................... 39 Register Description (Continued)...................................................................................................................................... 40 Register Description (Continued)...................................................................................................................................... 41 Register Description (Continued)...................................................................................................................................... 42 Register Description (Continued)...................................................................................................................................... 43 Absolute Maximum Ratings(1) ............................................................................................................................................ 44 Operating Ratings(2) ............................................................................................................................................................ 44 Electrical Characteristics(3) ................................................................................................................................................ 44 Electrical Characteristics(3) (Continued) ........................................................................................................................... 45 Timing Diagrams ................................................................................................................................................................. 46 MII SQE Timing (10Base-T) ............................................................................................................................................. 46 July 2010 5 M9999-070910-1.0 Micrel, Inc. KSZ8051MNL/RNL MII Transmit Timing (10Base-T) ....................................................................................................................................... 47 MII Receive Timing (10Base-T) ........................................................................................................................................ 48 MII Transmit Timing (100Base-TX) .................................................................................................................................. 49 MII Receive Timing (100Base-TX) ................................................................................................................................... 50 RMII Timing....................................................................................................................................................................... 51 Auto-Negotiation Timing ................................................................................................................................................... 52 MDC/MDIO Timing ........................................................................................................................................................... 53 Reset Timing..................................................................................................................................................................... 54 Reset Circuit ........................................................................................................................................................................ 55 Reference Circuits for LED Strapping Pins...................................................................................................................... 56 Magnetics Specification ..................................................................................................................................................... 57 Reference Clock – Connection and Selection.................................................................................................................. 57 Package Information........................................................................................................................................................... 59 July 2010 6 M9999-070910-1.0 Micrel, Inc. KSZ8051MNL/RNL List of Figures Figure 1. Auto-Negotiation Flow Chart................................................................................................................................. 21 Figure 2. KSZ8051MNL MII Interface .................................................................................................................................. 23 Figure 3. KSZ8051RNL RMII Interface (25MHz Clock Mode) ............................................................................................ 26 Figure 4. KSZ8051RNL RMII Interface (50MHz Clock Mode) ............................................................................................ 26 Figure 5. KSZ8051MNL/RNL and KSZ8041FTL Back-to-Back Media Converter ............................................................... 27 Figure 6. Typical Straight Cable Connection ....................................................................................................................... 29 Figure 7. Typical Crossover Cable Connection ................................................................................................................... 30 Figure 8. KSZ8051MNL/RNL Power and Ground Connections........................................................................................... 33 Figure 9. MII SQE Timing (10Base-T) ................................................................................................................................. 46 Figure 10. MII Transmit Timing (10Base-T) ......................................................................................................................... 47 Figure 11. MII Receive Timing (10Base-T) .......................................................................................................................... 48 Figure 12. MII Transmit Timing (100Base-TX)..................................................................................................................... 49 Figure 13. MII Receive Timing (100Base-TX)...................................................................................................................... 50 Figure 14. RMII Timing – Data Received from RMII ............................................................................................................ 51 Figure 15. RMII Timing – Data Input to RMII ....................................................................................................................... 51 Figure 16. Auto-Negotiation Fast Link Pulse (FLP) Timing ................................................................................................. 52 Figure 17. MDC/MDIO Timing.............................................................................................................................................. 53 Figure 18. Reset Timing....................................................................................................................................................... 54 Figure 19. Recommended Reset Circuit.............................................................................................................................. 55 Figure 20. Recommended Reset Circuit for interfacing with CPU/FPGA Reset Output...................................................... 55 Figure 21. Reference Circuits for LED Strapping Pins......................................................................................................... 56 Figure 22. 25MHz Crystal / Oscillator Reference Clock Connection ................................................................................... 57 Figure 23. 50MHz Oscillator Reference Clock Connection ................................................................................................. 58 July 2010 7 M9999-070910-1.0 Micrel, Inc. KSZ8051MNL/RNL List of Tables Table 1. MII Signal Definition ............................................................................................................................................... 22 Table 2. RMII Signal Description.......................................................................................................................................... 24 Table 3. MII Signal Connection for MII Back-to-Back Mode (100Base-TX Copper Repeater)............................................ 27 Table 4. RMII Signal Connection for RMII Back-to-Back Mode (100Base-TX Copper Repeater) ...................................... 28 Table 5. MII Management Frame Format – for KSZ8051MNL/RNL .................................................................................... 28 Table 6. MDI/MDI-X Pin Definition ....................................................................................................................................... 29 Table 7. NAND Tree Test Pin Order – for KSZ8051MNL .................................................................................................... 31 Table 8. NAND Tree Test Pin Order – for KSZ8051RNL .................................................................................................... 31 Table 9. KSZ8051MNL/RNL Power Pin Description............................................................................................................ 33 Table 10. MII SQE Timing (10Base-T) Parameters ............................................................................................................. 46 Table 11. MII Transmit Timing (10Base-T) Parameters ...................................................................................................... 47 Table 12. MII Receive Timing (10Base-T) Parameters ....................................................................................................... 48 Table 13. MII Transmit Timing (100Base-TX) Parameters .................................................................................................. 49 Table 14. MII Receive Timing (100Base-TX) Parameters ................................................................................................... 50 Table 15. RMII Timing Parameters – KSZ8051RNL (25MHz input to XI pin, 50MHz output from REF_CLK pin).............. 51 Table 16. RMII Timing Parameters – KSZ8051RNL (50MHz input to XI pin)...................................................................... 51 Table 17. Auto-Negotiation Fast Link Pulse (FLP) Timing Parameters ............................................................................... 52 Table 18. MDC/MDIO Timing Parameters ........................................................................................................................... 53 Table 19. Reset Timing Parameters .................................................................................................................................... 54 Table 20. Magnetics Selection Criteria ................................................................................................................................ 57 Table 21. Qualified Single Port 10/100 Magnetics............................................................................................................... 57 Table 22. 25MHz Crystal / Reference Clock Selection Criteria ........................................................................................... 58 Table 23. 50MHz Oscillator / Reference Clock Selection Criteria ....................................................................................... 58 July 2010 8 M9999-070910-1.0 Micrel, Inc. KSZ8051MNL/RNL Pin Configuration – KSZ8051MNL 32-Pin (5mm x 5mm) QFN July 2010 9 M9999-070910-1.0 Micrel, Inc. KSZ8051MNL/RNL Pin Description – KSZ8051MNL Pin Number 1 2 3 4 5 6 7 8 9 10 11 Pin Name GND VDD_1.2 VDDA_3.3 RXM RXP TXM TXP XO XI REXT MDIO Type P P I/O I/O I/O I/O O I I I/O (1) Pin Function Ground 1.2V core VDD 3.3V analog VDD Physical receive or transmit signal (- differential) Physical receive or transmit signal (+ differential) Physical transmit or receive signal (- differential) Physical transmit or receive signal (+ differential) Crystal feedback – for 25 MHz crystal This pin is a no connect if oscillator or external clock source is used. Crystal / Oscillator / External Clock Input 25MHz +/-50ppm Set physical transmit output current Connect a 6.49KΩ resistor to ground on this pin. Management Interface (MII) Data I/O This pin has a weak pull-up, is open drain like, and requires an external 1.0KΩ pullup resistor. (power supplied by KSZ8051MNL) Decouple with 2.2uF and 0.1uF capacitors to ground. Gnd 12 13 MDC RXD3 / PHYAD0 I Ipu/O Management Interface (MII) Clock Input This clock pin is synchronous to the MDIO data pin. MII Mode: Config Mode: MII Receive Data Output[3] (2) / The pull-up/pull-down value is latched as PHYADDR[0] at the de-assertion of reset. See “Strapping Options” section for details. MII Receive Data Output[2] (2) 14 RXD2 / PHYAD1 Ipd/O MII Mode: Config Mode: / The pull-up/pull-down value is latched as PHYADDR[1] at the de-assertion of reset. See “Strapping Options” section for details. MII Receive Data Output[1] (2) 15 RXD1 / PHYAD2 Ipd/O MII Mode: Config Mode: / The pull-up/pull-down value is latched as PHYADDR[2] at the de-assertion of reset. See “Strapping Options” section for details. MII Receive Data Output[0] (2) 16 RXD0 / DUPLEX Ipu/O MII Mode: Config Mode: / The pull-up/pull-down value is latched as DUPLEX at the de-assertion of reset. See “Strapping Options” section for details. MII Receive Data Valid Output / The pull-up/pull-down value is latched as CONFIG2 at the de-assertion of reset. See “Strapping Options” section for details. MII Receive Clock Output The pull-up/pull-down value is latched as B-CAST_OFF at the de-assertion of reset. See “Strapping Options” section for details. MII Receive Error Output / The pull-up/pull-down value is latched as ISOLATE at the de-assertion of reset. See “Strapping Options” section for details. 17 18 VDDIO RXDV / CONFIG2 P Ipd/O 3.3V, 2.5V or 1.8V digital VDD MII Mode: Config Mode: 19 RXC / B-CAST_OFF Ipd/O MII Mode: Config Mode: 20 RXER / ISO Ipd/O MII Mode: Config Mode: 21 INTRP / Ipu/Opu Interrupt Output: Programmable Interrupt Output This pin has a weak pull-up, is open drain like, and requires an external 1.0KΩ pullup resistor. July 2010 10 M9999-070910-1.0 Micrel, Inc. Pin Number Pin Name NAND_Tree# Type (1) KSZ8051MNL/RNL Pin Function Config Mode: The pull-up/pull-down value is latched as NAND Tree# at the de-assertion of reset. See “Strapping Options” section for details. MII Transmit Clock Output MII Transmit Clock Input (3) (3) (3) (3) 22 23 24 25 26 27 28 TXC TXEN TXD0 TXD1 TXD2 TXD3 COL / CONFIG0 I/O I I I I I Ipd/O MII Mode: MII Back-to-Back Mode: MII Mode: MII Mode: MII Mode: MII Mode: MII Mode: MII Mode: Config Mode: MII Transmit Enable Input MII Transmit Data Input[0] MII Transmit Data Input[1] MII Transmit Data Input[2] MII Transmit Data Input[3] MII Collision Detect Output / The pull-up/pull-down value is latched as CONFIG0 at the de-assertion of reset. See “Strapping Options” section for details. MII Carrier Sense Output / The pull-up/pull-down value is latched as CONFIG1 at the de-assertion of reset. See “Strapping Options” section for details. Programmable LED0 Output / Latched as Auto-Negotiation Enable (register 0h, bit 12) at the de-assertion of reset. See “Strapping Options” section for details. 29 CRS / CONFIG1 Ipd/O MII Mode: Config Mode: 30 LED0 / NWAYEN Ipu/O LED Output: Config Mode: The LED0 pin is programmable via register 1Fh bits [5:4], and is defined as follows. LED mode = [00] Link/Activity No Link Link Activity LED mode = [01] Link No Link Link Pin State High Low LED Definition OFF ON Reserved Pin State High Low Toggle LED Definition OFF ON Blinking LED mode = [10], [11] 31 LED1 / SPEED Ipu/O LED Output: Config Mode: reset. Programmable LED1 Output / Latched as SPEED (register 0h, bit 13) at the de-assertion of See “Strapping Options” section for details. The LED1 pin is programmable via register 1Fh bits [5:4], and is defined as follows. LED mode = [00] Speed 10Base-T 100Base-TX LED mode = [01] Activity No Activity Pin State High LED Definition OFF Pin State High Low LED Definition OFF ON July 2010 11 M9999-070910-1.0 Micrel, Inc. Pin Number Pin Name Type (1) KSZ8051MNL/RNL Pin Function Activity Toggle Blinking Reserved LED mode = [10], [11] 32 PADDLE Notes: 1. P = Power supply. Gnd = Ground. I = Input. O = Output. I/O = Bi-directional. RST# GND I Gnd Chip Reset (active low) Ground Ipu/O = Input with internal pull-up (see Electrical Characteristics for value) during power-up/reset; output pin otherwise. Ipd/O = Input with internal pull-down (see Electrical Characteristics for value) during power-up/reset; output pin otherwise. Ipu/Opu = Input with internal pull-up (see Electrical Characteristics for value) during power-up/reset; output pin with internal pull-up (see Electrical Characteristics for value) otherwise. 2. 3. MII Rx Mode: The RXD[3:0] bits are synchronous with RXC. When RXDV is asserted, RXD[3:0] presents valid data to the MAC. RXD[3:0] is invalid data from the PHY when RXDV is de-asserted. MII Tx Mode: The TXD[3:0] bits are synchronous with TXC. When TXEN is asserted, TXD[3:0] presents valid data from the MAC. TXD[3:0] has no effect on the PHY when TXEN is de-asserted. July 2010 12 M9999-070910-1.0 Micrel, Inc. KSZ8051MNL/RNL Strapping Options – KSZ8051MNL Pin Number 15 14 13 Pin Name PHYAD2 PHYAD1 PHYAD0 Type (1) Pin Function The PHY Address is latched at de-assertion of reset and is configurable to any value from 0 to 7. The default PHY Address is 00001. PHY Address 00000 is enabled only if the B-CAST_OFF strapping pin is pulled high. PHY Address bits [4:3] are set to ‘00’ by default. Ipd/O Ipd/O Ipu/O 18 29 28 CONFIG2 CONFIG1 CONFIG0 Ipd/O Ipd/O Ipd/O The CONFIG[2:0] strap-in pins are latched at the de-assertion of reset. CONFIG[2:0] 000 110 001 – 101, 111 Mode MII (default) MII Back-to-Back Reserved – not used 20 ISO Ipd/O ISOLATE mode Pull-up = Enable Pull-down (default) = Disable At the de-assertion of reset, this pin value is latched into register 0h bit 10. 31 SPEED Ipu/O SPEED mode Pull-up (default) = 100Mbps Pull-down = 10Mbps At the de-assertion of reset, this pin value is latched into register 0h bit 13 as the Speed Select, and also is latched into register 4h (Auto-Negotiation Advertisement) as the Speed capability support. 16 DUPLEX Ipu/O DUPLEX mode Pull-up (default) = Half Duplex Pull-down = Full Duplex At the de-assertion of reset, this pin value is latched into register 0h bit 8. 30 NWAYEN Ipu/O Nway Auto-Negotiation Enable Pull-up (default) = Enable Auto-Negotiation Pull-down = Disable Auto-Negotiation At the de-assertion of reset, this pin value is latched into register 0h bit 12. 19 B-CAST_OFF Ipd/O Broadcast Off – for PHY Address 0 Pull-up = PHY Address 0 is set as an unique PHY address Pull-down (default) = PHY Address 0 is set as a broadcast PHY address At the de-assertion of reset, this pin value is latched by the chip. 21 NAND_Tree# Ipu/Opu NAND Tree Mode Pull-up (default) = Disable Pull-down = Enable At the de-assertion of reset, this pin value is latched by the chip. Note: 1. Ipu/O = Input with internal pull-up (see Electrical Characteristics for value) during power-up/reset; output pin otherwise. Ipd/O = Input with internal pull-down (see Electrical Characteristics for value) during power-up/reset; output pin otherwise. Ipu/Opu = Input with internal pull-up (see Electrical Characteristics for value) during power-up/reset; output pin with internal pull-up (see Electrical Characteristics for value) otherwise. The strap-in pins are latched at the de-assertion of reset. In some systems, the MAC MII receive input pins may drive high/low during power-up or reset, and consequently cause the PHY strap-in pins on the MII signals to be latched to the unintended high/low states. In this case, external pull-ups (4.7K) or pull-downs (1.0K) should be added on these PHY strap-in pins to ensure the intended values are strapped-in correctly. July 2010 13 M9999-070910-1.0 Micrel, Inc. KSZ8051MNL/RNL Pin Configuration – KSZ8051RNL 32-Pin (5mm x 5mm) QFN July 2010 14 M9999-070910-1.0 Micrel, Inc. KSZ8051MNL/RNL Pin Description – KSZ8051RNL Pin Number 1 2 3 4 5 6 7 8 9 10 11 Pin Name GND VDD_1.2 VDDA_3.3 RXM RXP TXM TXP XO XI REXT MDIO Type P P I/O I/O I/O I/O O I I I/O (1) Pin Function Ground 1.2V core VDD 3.3V analog VDD Physical receive or transmit signal (- differential) Physical receive or transmit signal (+ differential) Physical transmit or receive signal (- differential) Physical transmit or receive signal (+ differential) Crystal feedback – for 25 MHz crystal This pin is a no connect if oscillator or external clock source is used. 25MHz Mode: 50MHz Mode: 25MHz +/-50ppm Crystal / Oscillator / External Clock Input 50MHz +/-50ppm Oscillator / External Clock Input (power supplied by KSZ8051RNL) Decouple with 2.2uF and 0.1uF capacitors to ground. Gnd Set physical transmit output current Connect a 6.49KΩ resistor-to-ground on this pin. Management Interface (MII) Data I/O This pin has a weak pull-up, is open drain like, and requires an external 1.0KΩ pullup resistor. 12 13 14 15 MDC PHYAD0 PHYAD1 RXD1 / PHYAD2 I Ipu/O Ipd/O Ipd/O Management Interface (MII) Clock Input This clock pin is synchronous to the MDIO data pin. The pull-up/pull-down value is latched as PHYADDR[0] at the de-assertion of reset. See “Strapping Options” section for details. The pull-up/pull-down value is latched as PHYADDR[1] at the de-assertion of reset. See “Strapping Options” section for details. RMII Mode: Config Mode: RMII Receive Data Output[1] (2) / The pull-up/pull-down value is latched as PHYADDR[2] at the de-assertion of reset. See “Strapping Options” section for details. RMII Receive Data Output[0] (2) 16 RXD0 / DUPLEX Ipu/O RMII Mode: Config Mode: / The pull-up/pull-down value is latched as DUPLEX at the de-assertion of reset. See “Strapping Options” section for details. RMII Carrier Sense/Receive Data Valid Output / The pull-up/pull-down value is latched as CONFIG2 at the de-assertion of reset. See “Strapping Options” section for details. 25MHz Mode: This pin provides the 50MHz RMII reference clock output to the MAC. See also XI (pin 9). 50MHz Mode: This pin is a no connect. See also XI (pin 9). The pull-up/pull-down value is latched as B-CAST_OFF at the de-assertion of reset. See “Strapping Options” section for details. RMII Receive Error Output / The pull-up/pull-down value is latched as ISOLATE at the de-assertion of reset. See “Strapping Options” section for details. 17 18 VDDIO CRS_DV / CONFIG2 P Ipd/O 3.3V, 2.5V or 1.8V digital VDD RMII Mode: Config Mode: 19 REF_CLK / Ipd/O RMII Mode: B-CAST_OFF 20 RXER / ISO 21 INTRP / Ipu/Opu Ipd/O Config Mode: RMII Mode: Config Mode: Interrupt Output: Programmable Interrupt Output This pin has a weak pull-up, is open drain like, and requires an external 1.0KΩ pullup resistor. July 2010 15 M9999-070910-1.0 Micrel, Inc. Pin Number Pin Name NAND_Tree# 22 23 24 25 26 27 28 29 30 NC TXEN TXD0 TXD1 NC NC CONFIG0 CONFIG1 LED0 / NWAYEN O I I I I I Ipd/O Ipd/O Ipu/O Type (1) KSZ8051MNL/RNL Pin Function Config Mode: The pull-up/pull-down value is latched as NAND Tree# at the de-assertion of reset. See “Strapping Options” section for details. No connect- It is recommended to tie this unused pin directly to ground. RMII Transmit Enable Input RMII Transmit Data Input[0] RMII Transmit Data Input[1] (3) (3) No connect- It is recommended to tie this unused pin directly to ground. No connect- It is recommended to tie this unused pin directly to ground. The pull-up/pull-down value is latched as CONFIG0 at the de-assertion of reset. See “Strapping Options” section for details. The pull-up/pull-down value is latched as CONFIG1 at the de-assertion of reset. See “Strapping Options” section for details. LED Output: Config Mode: Programmable LED0 Output / Latched as Auto-Negotiation Enable (register 0h, bit 12) at the de-assertion of reset. See “Strapping Options” section for details. The LED0 pin is programmable via register 1Fh bits [5:4], and is defined as follows. LED mode = [00] Link/Activity No Link Link Activity LED mode = [01] Link No Link Link Pin State High Low LED Definition OFF ON Reserved Pin State High Low Toggle LED Definition OFF ON Blinking LED mode = [10], [11] 31 LED1 / SPEED Ipu/O LED Output: Config Mode: reset. Programmable LED1 Output / Latched as SPEED (register 0h, bit 13) at the de-assertion of See “Strapping Options” section for details. The LED1 pin is programmable via register 1Fh bits [5:4], and is defined as follows. LED mode = [00] Speed 10Base-T 100Base-TX LED mode = [01] Activity No Activity Activity Pin State High Toggle LED Definition OFF Blinking Reserved Pin State High Low LED Definition OFF ON LED mode = [10], [11] July 2010 16 M9999-070910-1.0 Micrel, Inc. Pin Number 32 PADDLE Notes: 1. P = Power supply. Gnd = Ground. I = Input. O = Output. I/O = Bi-directional. Ipu/O = Input with internal pull-up (see Electrical Characteristics for value) during power-up/reset; output pin otherwise. Ipd/O = Input with internal pull-down (see Electrical Characteristics for value) during power-up/reset; output pin otherwise. KSZ8051MNL/RNL Pin Name RST# GND Type I Gnd (1) Pin Function Chip Reset (active low) Ground Ipu/Opu = Input with internal pull-up (see Electrical Characteristics for value) during power-up/reset; output pin with internal pull-up (see Electrical Characteristics for value) otherwise. 2. 3. RMII Rx Mode: The RXD[1:0] bits are synchronous with the 50MHz RMII Reference Clock. For each clock period in which CRS_DV is asserted, two bits of recovered data are sent by the PHY to the MAC. RMII Tx Mode: The TXD[1:0] bits are synchronous with the 50MHz RMII Reference Clock . For each clock period in which TXEN is asserted, two bits of data are received by the PHY from the MAC. July 2010 17 M9999-070910-1.0 Micrel, Inc. KSZ8051MNL/RNL Strapping Options – KSZ8051RNL Pin Number 15 14 13 Pin Name PHYAD2 PHYAD1 PHYAD0 Type (1) Pin Function The PHY Address is latched at de-assertion of reset and is configurable to any value from 0 to 7. The default PHY Address is 00001. PHY Address 00000 is enabled only if the B-CAST_OFF strapping pin is pulled high. PHY Address bits [4:3] are set to ‘00’ by default. Ipd/O Ipd/O Ipu/O 18 29 28 CONFIG2 CONFIG1 CONFIG0 Ipd/O Ipd/O Ipd/O The CONFIG[2:0] strap-in pins are latched at the de-assertion of reset. CONFIG[2:0] 001 101 000, 010 – 100, 110, 111 Mode RMII RMII Back-to-Back Reserved – not used 20 ISO Ipd/O ISOLATE mode Pull-up = Enable Pull-down (default) = Disable At the de-assertion of reset, this pin value is latched into register 0h bit 10. 31 SPEED Ipu/O SPEED mode Pull-up (default) = 100Mbps Pull-down = 10Mbps At the de-assertion of reset, this pin value is latched into register 0h bit 13 as the Speed Select, and also is latched into register 4h (Auto-Negotiation Advertisement) as the Speed capability support. 16 DUPLEX Ipu/O DUPLEX mode Pull-up (default) = Half Duplex Pull-down = Full Duplex At the de-assertion of reset, this pin value is latched into register 0h bit 8. 30 NWAYEN Ipu/O Nway Auto-Negotiation Enable Pull-up (default) = Enable Auto-Negotiation Pull-down = Disable Auto-Negotiation At the de-assertion of reset, this pin value is latched into register 0h bit 12. 19 B-CAST_OFF Ipd/O Broadcast Off – for PHY Address 0 Pull-up = PHY Address 0 is set as an unique PHY address Pull-down (default) = PHY Address 0 is set as a broadcast PHY address At the de-assertion of reset, this pin value is latched by the chip. 21 NAND_Tree# Ipu/Opu NAND Tree Mode Pull-up (default) = Disable Pull-down = Enable At the de-assertion of reset, this pin value is latched by the chip. Note: 1. Ipu/O = Input with internal pull-up (see Electrical Characteristics for value) during power-up/reset; output pin otherwise. Ipd/O = Input with internal pull-down (see Electrical Characteristics for value) during power-up/reset; output pin otherwise. Ipu/Opu = Input with internal pull-up (see Electrical Characteristics for value) during power-up/reset; output pin with internal pull-up (see Electrical Characteristics for value) otherwise. The strap-in pins are latched at the de-assertion of reset. In some systems, the MAC MII receive input pins may drive high/low during power-up or reset, and consequently cause the PHY strap-in pins on the RMII signals to be latched to the unintended high/low states. In this case, external pull-ups (4.7K) or pull-downs (1.0K) should be added on these PHY strap-in pins to ensure the intended values are strapped-in correctly. July 2010 18 M9999-070910-1.0 Micrel, Inc. KSZ8051MNL/RNL Functional Description: 10Base-T/100Base-TX Transceiver The KSZ8051MNL/RNL is an integrated single 3.3V supply Fast Ethernet transceiver. It is fully compliant with the IEEE 802.3 Specification, and reduces board cost and simplifies board layout by using on-chip termination resistors for the two differential pairs and by integrating the regulator to supply the 1.2V core. On the copper media side, the KSZ8051MNL/RNL supports 10Base-T and 100Base-TX for transmission and reception of data over a standard CAT-5 unshielded twisted pair (UTP) cable, and HP auto MDI/MDI-X for reliable detection of and correction for straight-through and crossover cables. On the MAC processor side, the KSZ8051MNL offers the Media Independent Interface (MII) and the KSZ8051RNL offers the Reduced Media Independent Interface (RMII) for direct connection with MII/RMII compliant Ethernet MAC processors and switches. The MII management bus option gives the MAC processor complete access to the KSZ8051MNL/RNL control and status registers. Additionally, an interrupt pin eliminates the need for the processor to poll for PHY status change. 100Base-TX Transmit The 100Base-TX transmit function performs parallel-to-serial conversion, 4B/5B encoding, scrambling, NRZ-to-NRZI conversion, and MLT3 encoding and transmission. The circuitry starts with a parallel-to-serial conversion, which converts the MII data from the MAC into a 125MHz serial bit stream. The data and control stream is then converted into 4B/5B coding and followed by a scrambler. The serialized data is further converted from NRZ-to-NRZI format, and then transmitted in MLT3 current output. The output current is set by an external 6.49kΩ 1% resistor for the 1:1 transformer ratio. The output signal has a typical rise/fall time of 4ns and complies with the ANSI TP-PMD standard regarding amplitude balance, overshoot, and timing jitter. The wave-shaped 10Base-T output is also incorporated into the 100Base-TX transmitter. 100Base-TX Receive The 100Base-TX receiver function performs adaptive equalization, DC restoration, MLT3-to-NRZI conversion, data and clock recovery, NRZI-to-NRZ conversion, de-scrambling, 4B/5B decoding, and serial-to-parallel conversion. The receiving side starts with the equalization filter to compensate for inter-symbol interference (ISI) over the twisted pair cable. Since the amplitude loss and phase distortion is a function of the cable length, the equalizer must adjust its characteristics to optimize performance. In this design, the variable equalizer makes an initial estimation based on comparisons of incoming signal strength against some known cable characteristics, and then tunes itself for optimization. This is an ongoing process and self-adjusts against environmental changes such as temperature variations. Next, the equalized signal goes through a DC restoration and data conversion block. The DC restoration circuit is used to compensate for the effect of baseline wander and to improve the dynamic range. The differential data conversion circuit converts the MLT3 format back to NRZI. The slicing threshold is also adaptive. The clock recovery circuit extracts the 125MHz clock from the edges of the NRZI signal. This recovered clock is then used to convert the NRZI signal into the NRZ format. This signal is sent through the de-scrambler followed by the 4B/5B decoder. Finally, the NRZ serial data is converted to the MII format and provided as the input data to the MAC. 10Base-T Transmit The 10Base-T drivers are incorporated with the 100Base-TX drivers to allow for transmission using the same magnetic. The drivers perform internal wave-shaping and pre-emphasis, and output 10Base-T signals with a typical amplitude of 2.5V peak. The 10Base-T signals have harmonic contents that are at least 27dB below the fundamental frequency when driven by an all-ones Manchester-encoded signal. 10Base-T Receive On the receive side, input buffer and level detecting squelch circuits are employed. A differential input receiver circuit and a PLL performs the decoding function. The Manchester-encoded data stream is separated into clock signal and NRZ data. A squelch circuit rejects signals with levels less than 400 mV or with short pulse widths to prevent noise at the RXP and RXM inputs from falsely trigger the decoder. When the input exceeds the squelch limit, the PLL locks onto the incoming signal and the KSZ8051MNL/RNL decodes a data frame. The receive clock is kept active during idle periods in between data reception. July 2010 19 M9999-070910-1.0 Micrel, Inc. KSZ8051MNL/RNL Scrambler/De-scrambler (100Base-TX only) The scrambler is used to spread the power spectrum of the transmitted signal to reduce EMI and baseline wander, and the de-scrambler is needed to recover the scrambled signal. SQE and Jabber Function (10Base-T only) In 10Base-T operation, a short pulse is put out on the COL pin after each frame is transmitted. This SQE Test is required as a test of the 10Base-T transmit/receive path. If transmit enable (TXEN) is high for more than 20 ms (jabbering), the 10Base-T transmitter is disabled and COL is asserted high. If TXEN is then driven low for more than 250 ms, the 10BaseT transmitter is re-enabled and COL is de-asserted (returns to low). PLL Clock Synthesizer The KSZ8051MNL/RNL generates all internal clocks and all external clocks for system timing from an external 25MHz crystal, oscillator, or reference clock. For the KSZ8051RNL in RMII 50MHz clock mode, these clocks are generated from an external 50MHz oscillator or system clock. Auto-Negotiation The KSZ8051MNL/RNL conforms to the auto-negotiation protocol, defined in Clause 28 of the IEEE 802.3 Specification. Auto-negotiation allows UTP (Unshielded Twisted Pair) link partners to select the highest common mode of operation. During auto-negotiation, link partners advertise capabilities across the UTP link to each other, and then compare their own capabilities with those they received from their link partners. The highest speed and duplex setting that is common to the two link partners is selected as the mode of operation. The following list shows the speed and duplex operation mode from highest to lowest priority. • • • Priority 1: 100Base-TX, full-duplex Priority 2: 100Base-TX, half-duplex Priority 3: 10Base-T, full-duplex • Priority 4: 10Base-T, half-duplex If auto-negotiation is not supported or the KSZ8051MNL/RNL link partner is forced to bypass auto-negotiation, then the KSZ8051MNL/RNL sets its operating mode by observing the signal at its receiver. This is known as parallel detection, and allows the KSZ8051MNL/RNL to establish link by listening for a fixed signal protocol in the absence of auto-negotiation advertisement protocol. Auto-negotiation is enabled by either hardware pin strapping (NWAYEN, pin 30) or software (register 0h, bit 12). By default, auto-negotiation is enabled after power-up or hardware reset. Afterwards, auto-negotiation can be enabled or disabled by register 0h, bit 12. If auto-negotiation is disabled, the speed is set by register 0h, bit 13, and the duplex is set by register 0h, bit 8. The auto-negotiation link up process is shown in the following flow chart. July 2010 20 M9999-070910-1.0 Micrel, Inc. KSZ8051MNL/RNL Figure 1. Auto-Negotiation Flow Chart MII Data Interface (KSZ8051MNL only) The Media Independent Interface (MII) is compliant with the IEEE 802.3 Specification. It provides a common interface between MII PHYs and MACs, and has the following key characteristics: • • • • Pin count is 15 pins (6 pins for data transmission, 7 pins for data reception, and 2 pins for carrier and collision indication). 10Mbps and 100Mbps data rates are supported at both half and full duplex. Data transmission and reception are independent and belong to separate signal groups. Transmit data and receive data are each 4-bit wide, a nibble. By default, the KSZ8051MNL is configured to MII mode after it is powered up or hardware reset with the following: • • A 25MHz crystal connected to XI, XO (pins 9, 8), or an external 25MHz clock source (oscillator) connected to XI. The CONFIG[2:0] strapping pins (pins 18, 29, 28) set to ‘000’ (default setting). July 2010 21 M9999-070910-1.0 Micrel, Inc. KSZ8051MNL/RNL MII Signal Definition The following table describes the MII signals. Refer to Clause 22 of the IEEE 802.3 Specification for detailed information. Direction (with respect to PHY, KSZ8051MNL signal) Output Input Input Output Output Output Output Output Output MII Signal Name TXC TXEN TXD[3:0] RXC RXDV RXD[3:0] RXER CRS COL Direction (with respect to MAC) Input Output Output Input Input Input Input, or (not required) Input Input Description Transmit Clock (2.5MHz for 10Mbps; 25MHz for 100Mbps) Transmit Enable Transmit Data [3:0] Receive Clock (2.5MHz for 10Mbps; 25MHz for 100Mbps) Receive Data Valid Receive Data [3:0] Receive Error Carrier Sense Collision Detection Table 1. MII Signal Definition Transmit Clock (TXC) TXC is sourced by the PHY. It is a continuous clock that provides the timing reference for TXEN and TXD[3:0]. TXC is 2.5MHz for 10Mbps operation and 25MHz for 100Mbps operation. Transmit Enable (TXEN) TXEN indicates the MAC is presenting nibbles on TXD[3:0] for transmission. It is asserted synchronously with the first nibble of the preamble and remains asserted while all nibbles to be transmitted are presented on the MII, and is negated prior to the first TXC following the final nibble of a frame. TXEN transitions synchronously with respect to TXC. Transmit Data [3:0] (TXD[3:0]) TXD[3:0] transitions synchronously with respect to TXC. When TXEN is asserted, TXD[3:0] are accepted for transmission by the PHY. TXD[3:0] is ”00” to indicate idle when TXEN is de-asserted. Values other than “00” on TXD[3:0] while TXEN is de-asserted are ignored by the PHY. Receive Clock (RXC) RXC provides the timing reference for RXDV, RXD[3:0], and RXER. • • In 10Mbps mode, RXC is recovered from the line while carrier is active. RXC is derived from the PHY’s reference clock when the line is idle, or link is down. In 100Mbps mode, RXC is continuously recovered from the line. If link is down, RXC is derived from the PHY’s reference clock. RXC is 2.5MHz for 10Mbps operation and 25MHz for 100Mbps operation. Receive Data Valid (RXDV) RXDV is driven by the PHY to indicate that the PHY is presenting recovered and decoded nibbles on RXD[3:0]. • In 10Mbps mode, RXDV is asserted with the first nibble of the SFD (Start of Frame Delimiter), “5D”, and remains asserted until the end of the frame. • In 100Mbps mode, RXDV is asserted from the first nibble of the preamble to the last nibble of the frame. RXDV transitions synchronously with respect to RXC. July 2010 22 M9999-070910-1.0 Micrel, Inc. KSZ8051MNL/RNL Receive Data[3:0] (RXD[3:0]) RXD[3:0] transitions synchronously with respect to RXC. For each clock period in which RXDV is asserted, RXD[3:0] transfers a nibble of recovered data from the PHY. Receive Error (RXER) RXER is asserted for one or more RXC periods to indicate that a Symbol Error (e.g., a coding error that a PHY is capable of detecting, and that may otherwise be undetectable by the MAC sub-layer) was detected somewhere in the frame presently being transferred from the PHY. RXER transitions synchronously with respect to RXC. While RXDV is de-asserted, RXER has no effect on the MAC. Carrier Sense (CRS) CRS is asserted and de-asserted as follows: • • In 10Mbps mode, CRS assertion is based on the reception of valid preambles. CRS de-assertion is based upon the reception of an end-of-frame (EOF) marker. In 100Mbps mode, CRS is asserted when a start-of-stream delimiter or /J/K symbol pair is detected. CRS is deasserted when an end-of-stream delimiter or /T/R symbol pair is detected. Additionally, the PMA layer de-asserts CRS if IDLE symbols are received without /T/R. Collision (COL) COL is asserted in half-duplex mode whenever the transmitter and receiver are simultaneously active on the line. This is used to inform the MAC that a collision has occurred during its transmission to the PHY. COL transitions asynchronously with respect to TXC and RXC. MII Signal Diagram The KSZ8051MNL MII pin connections to the MAC are shown in the following figure. Figure 2. KSZ8051MNL MII Interface July 2010 23 M9999-070910-1.0 Micrel, Inc. KSZ8051MNL/RNL RMII Data Interface (KSZ8051RNL only) The Reduced Media Independent Interface (RMII) specifies a low pin count Media Independent Interface (MII). It provides a common interface between physical layer and MAC layer devices, and has the following key characteristics: • • • • Pin count is 8 pins (3 pins for data transmission, 4 pins for data reception, 1 pin for the 50MHz reference clock). 10Mbps and 100Mbps data rates are supported at both half and full duplex. Data transmission and reception are independent and belong to separate signal groups. Transmit data and receive data are each 2-bit wide, a dibit. RMII – 25MHz Clock Mode The KSZ8051RNL is configured to RMII – 25MHz Clock Mode after it is powered up or hardware reset with the following: • • • A 25MHz crystal connected to XI, XO (pins 9, 8), or an external 25MHz clock source (oscillator) connected to XI. The CONFIG[2:0] strapping pins (pins 18, 29, 28) set to ‘001’. Register 1Fh, bit 7 is set to ‘0’ (default value) to select 25MHz Clock Mode. RMII – 50MHz Clock Mode The KSZ8051RNL is configured to RMII – 50MHz Clock Mode after it is powered up or hardware reset with the following: • • • An external 50MHz clock source (oscillator) connected to XI (pin 9). The CONFIG[2:0] strapping pins (pins 18, 29, 28) set to ‘001’. Register 1Fh, bit 7 is set to ‘1’ to select 50MHz Clock Mode. RMII Signal Definition The following table describes the RMII signals. Refer to RMII Specification v1.2 for detailed information. Direction (with respect to PHY, KSZ8051RNL signal) Output (25MHz clock mode) / (50MHz clock mode) TXEN TXD[1:0] CRS_DV RXD[1:0] RXER Input Input Output Output Output Direction (with respect to MAC) Input / Input or Output Output Input Input Input, or (not required) RMII Signal Name REF_CLK Description Synchronous 50 MHz reference clock for receive, transmit and control interface Transmit Enable Transmit Data [1:0] Carrier Sense/Receive Data Valid Receive Data [1:0] Receive Error Table 2. RMII Signal Description Reference Clock (REF_CLK) REF_CLK is a continuous 50MHz clock that provides the timing reference for TX_EN, TXD[1:0], CRS_DV, RXD[1:0], and RX_ER. For 25MHz Clock Mode, the KSZ8051RNL generates and outputs the 50MHz RMII REF_CLK to the MAC at REF_CLK (pin 19). For 50MHz Clock Mode, the KSZ8051RNL takes in the 50MHz RMII REF_CLK from the MAC or system board at XI (pin 9) and has the REF_CLK (pin 19) left as a no connect. July 2010 24 M9999-070910-1.0 Micrel, Inc. KSZ8051MNL/RNL Transmit Enable (TXEN) TXEN indicates that the MAC is presenting dibits on TXD[1:0] for transmission. It is asserted synchronously with the first dibit of the preamble and remains asserted while all dibits to be transmitted are presented on the RMII, and is negated prior to the first REF_CLK following the final dibit of a frame. TXEN transitions synchronously with respect to REF_CLK. Transmit Data [1:0] (TXD[1:0]) TXD[1:0] transitions synchronously with respect to REF_CLK. When TXEN is asserted, TXD[1:0] are accepted for transmission by the PHY. TXD[1:0] is ”00” to indicate idle when TXEN is de-asserted. Values other than “00” on TXD[1:0] while TXEN is de-asserted are ignored by the PHY. Carrier Sense/Receive Data Valid (CRS_DV) CRS_DV is asserted by the PHY when the receive medium is non-idle. It is asserted asynchronously on detection of carrier. This is when squelch is passed in 10Mbps mode, and when 2 non-contiguous zeroes in 10 bits are detected in 100Mbps mode. Loss of carrier results in the de-assertion of CRS_DV. So long as carrier detection criteria are met, CRS_DV remains asserted continuously from the first recovered dibit of the frame through the final recovered dibit, and it is negated prior to the first REF_CLK that follows the final dibit. The data on RXD[1:0] is considered valid once CRS_DV is asserted. However, since the assertion of CRS_DV is asynchronous relative to REF_CLK, the data on RXD[1:0] is "00" until proper receive signal decoding takes place. Receive Data [1:0] (RXD[1:0]) RXD[1:0] transitions synchronously with respect to REF_CLK. For each clock period in which CRS_DV is asserted, RXD[1:0] transfers two bits of recovered data from the PHY. RXD[1:0] is "00" to indicate idle when CRS_DV is de-asserted. Values other than “00” on RXD[1:0] while CRS_DV is deasserted are ignored by the MAC. Receive Error (RXER) RXER is asserted for one or more REF_CLK periods to indicate that a Symbol Error (e.g. a coding error that a PHY is capable of detecting, and that may otherwise be undetectable by the MAC sub-layer) was detected somewhere in the frame presently being transferred from the PHY. RXER transitions synchronously with respect to REF_CLK. While CRS_DV is de-asserted, RX_ER has no effect on the MAC. Collision Detection The MAC regenerates the COL signal of the MII from TXEN and CRS_DV. RMII Signal Diagram The KSZ8051RNL RMII pin connections to the MAC are shown in the following figures for 25MHz Clock Mode and 50MHz Clock Mode. July 2010 25 M9999-070910-1.0 Micrel, Inc. KSZ8051MNL/RNL RMII – 25MHz Clock Mode Figure 3. KSZ8051RNL RMII Interface (25MHz Clock Mode) RMII – 50MHz Clock Mode Figure 4. KSZ8051RNL RMII Interface (50MHz Clock Mode) July 2010 26 M9999-070910-1.0 Micrel, Inc. KSZ8051MNL/RNL Back-to-Back Mode – 100Mbps Copper Repeater / Media Converter Two KSZ8051MNL/RNL devices can be connected back-to-back to form a 100Base-TX to 100Base-TX copper repeater. A KSZ8051MNL/RNL and a KSZ8041FTL can be connected back-to-back to provide a low cost media converter solution. Media conversion is between 100Base-TX copper and 100Base-FX fiber. On the copper side, link up at 10Base-T is not allowed, and is blocked during auto-negotiation. Figure 5. KSZ8051MNL/RNL and KSZ8041FTL Back-to-Back Media Converter MII Back-to-Back Mode (KSZ8051MNL only) In MII Back-to-Back mode, a KSZ8051MNL interfaces with another KSZ8051MNL, or a KSZ8041FTL to provide a complete 100Mbps copper repeater, or media converter solution, respectively. The KSZ8051MNL devices are configured to MII Back-to-Back mode after power-up or reset with the following: • • • Strapping pin CONFIG[2:0] (pins 18, 29, 28) set to ‘110’ A common 25MHz reference clock connected to XI (pin 9) MII signals connected as shown in the following table. KSZ8051MNL (100Base-TX copper) [Device 1] Pin Name RXC RXDV RXD3 RXD2 RXD1 RXD0 TXC TXEN TXD3 TXD2 TXD1 TXD0 Pin Number 19 18 13 14 15 16 22 23 27 26 25 24 Pin Type Output Output Output Output Output Output Input Input Input Input Input Input Pin Name TXC TXEN TXD3 TXD2 TXD1 TXD0 RXC RXDV RXD3 RXD2 RXD1 RXD0 KSZ8051MNL (100Base-TX copper) [Device 2] Pin Number 22 23 27 26 25 24 19 18 13 14 15 16 Pin Type Input Input Input Input Input Input Output Output Output Output Output Output Table 3. MII Signal Connection for MII Back-to-Back Mode (100Base-TX Copper Repeater) July 2010 27 M9999-070910-1.0 Micrel, Inc. KSZ8051MNL/RNL RMII Back-to-Back Mode (KSZ8051RNL only) In RMII Back-to-Back mode, a KSZ8051RNL interfaces with another KSZ8051RNL, or a KSZ8041FTL to provide a complete 100Mbps copper repeater, or media converter solution, respectively. The KSZ8051RNL devices are configured to RMII Back-to-Back mode after power-up or reset with the following: • • • Strapping pin CONFIG[2:0] (pins 18, 29, 28) set to ‘101’ A common 50MHz reference clock connected to XI (pin 9) RMII signals connected as shown in the following table. KSZ8051RNL (100Base-TX copper) [Device 1] Pin Name CRSDV RXD1 RXD0 TXEN TXD1 TXD0 Pin Number 18 15 16 23 25 24 Pin Type Output Output Output Input Input Input Pin Name TXEN TXD1 TXD0 CRSDV RXD1 RXD0 KSZ8051RNL (100Base-TX copper) [Device 2] Pin Number 23 25 24 18 15 16 Pin Type Input Input Input Output Output Output Table 4. RMII Signal Connection for RMII Back-to-Back Mode (100Base-TX Copper Repeater) MII Management (MIIM) Interface The KSZ8051MNL/RNL supports the IEEE 802.3 MII Management Interface, also known as the Management Data Input / Output (MDIO) Interface. This interface enables upper-layer device, like a MAC processor, to monitor and control the state of the KSZ8051MNL/RNL. An external device with MIIM capability is used to read the PHY status and/or configure the PHY settings. Further details on the MIIM interface can be found in Clause 22.2.4 of the IEEE 802.3 Specification. The MIIM interface consists of the following: • • • A physical connection that incorporates the clock line (MDC) and the data line (MDIO). A specific protocol that operates across the aforementioned physical connection that allows the external controller to communicate with one or more PHY devices. A set of 16-bit MDIO registers. Registers [0:8] are standard registers, and their functions are defined per the IEEE 802.3 Specification. The additional registers are provided for expanded functionality. See “Register Map” section for details. As the default, the KSZ8051MNL/RNL supports unique PHY addresses 1 to 7, and broadcast PHY address 0. The latter is defined per the IEEE 802.3 Specification, and can be used to read/write to a single KSZ8051MNL/RNL device, or write to multiple KSZ8051MNL/RNL devices simultaneously. Optionally, PHY address 0 can be disabled as the broadcast address by either hardware pin strapping (B-CAST_OFF, pin 19) or software (register 16h, bit 9), and assigned as a unique PHY address. The PHYAD[2:0] strapping pins are used to assigned a unique PHY address between 0 and 7 to each KSZ8051MNL/RNL device. The following table shows the MII Management frame format for the KSZ8051MNL/RNL. Preamble Start of Frame Read/Write OP Code 10 01 PHY Address Bits [4:0] Read Write 32 1’s 32 1’s 01 01 00AAA 00AAA REG Address Bits [4:0] RRRRR RRRRR Z0 10 DDDDDDDD_DDDDDDDD DDDDDDDD_DDDDDDDD Z Z TA Data Bits [15:0] Idle Table 5. MII Management Frame Format – for KSZ8051MNL/RNL July 2010 28 M9999-070910-1.0 Micrel, Inc. KSZ8051MNL/RNL Interrupt (INTRP) INTRP (pin 21) is an optional interrupt signal that is used to inform the external controller that there has been a status update to the KSZ8051MNL/RNL PHY register. Register 1Bh, bits [15:8] are the interrupt control bits to enable and disable the conditions for asserting the INTRP signal. Register 1Bh, bits [7:0] are the interrupt status bits to indicate which interrupt conditions have occurred. The interrupt status bits are cleared after reading register 1Bh. Register 1Fh, bit 9 sets the interrupt level to active high or active low. The default is active low. The MII management bus option gives the MAC processor complete access to the KSZ8051MNL/RNL control and status registers. Additionally, an interrupt pin eliminates the need for the processor to poll the PHY for status change. HP Auto MDI/MDI-X HP Auto MDI/MDI-X configuration eliminates the confusion of whether to use a straight cable or a crossover cable between the KSZ8051MNL/RNL and its link partner. This feature allows the KSZ8051MNL/RNL to use either type of cable to connect with a link partner that is in either MDI or MDI-X mode. The auto-sense function detects transmit and receive pairs from the link partner, and then assigns transmit and receive pairs of the KSZ8051MNL/RNL accordingly. HP Auto MDI/MDI-X is enabled by default. It is disabled by writing a one to register 1Fh, bit 13. MDI and MDI-X mode is selected by register 1Fh, bit 14 if HP Auto MDI/MDI-X is disabled. An isolation transformer with symmetrical transmit and receive data paths is recommended to support auto MDI/MDI-X. The IEEE 802.3 Standard defines MDI and MDI-X as follows: MDI RJ-45 Pin 1 2 3 6 Signal TX+ TXRX+ RXRJ-45 Pin 1 2 3 6 MDI-X Signal RX+ RXTX+ TX- Table 6. MDI/MDI-X Pin Definition Straight Cable A straight cable connects a MDI device to a MDI-X device, or a MDI-X device to a MDI device. The following figure depicts a typical straight cable connection between a NIC card (MDI) and a switch, or hub (MDI-X). Figure 6. Typical Straight Cable Connection July 2010 29 M9999-070910-1.0 Micrel, Inc. KSZ8051MNL/RNL Crossover Cable A crossover cable connects a MDI device to another MDI device, or a MDI-X device to another MDI-X device. The following figure depicts a typical crossover cable connection between two switches or hubs (two MDI-X devices). Figure 7. Typical Crossover Cable Connection LinkMD® Cable Diagnostics The LinkMD® function utilizes time domain reflectometry (TDR) to analyze the cabling plant for common cabling problems, such as open circuits, short circuits and impedance mismatches. LinkMD® works by sending a pulse of known amplitude and duration down the MDI or MDI-X pair, and then analyzing the shape of the reflected signal to determine the type of fault. The time duration for the reflected signal to return provides the approximate distance to the cabling fault. The LinkMD® function processes this TDR information and presents it as a numerical value that can be translated to a cable distance. LinkMD® is initiated by accessing register 1Dh, the LinkMD® Control/Status Register, in conjunction with register 1Fh, the PHY Control 2 Register. The latter register is used to disable auto MDI/MDI-X and to select either MDI or MDI-X as the cable differential pair for testing. NAND Tree Support The KSZ8051MNL/RNL provides parametric NAND tree support for fault detection between chip I/Os and board. The NAND tree is a chain of nested NAND gates in which each KSZ8051MNL/RNL digital I/O (NAND tree input) pin is an input to one NAND gate along the chain. At the end of the chain, the CRS/CONFIG1 pin provides the output for the nested NAND gates. The NAND tree test process includes: • • • • Enabling NAND tree mode Pulling all NAND tree input pins high Driving low each NAND tree input pin sequentially per the NAND tree pin order Checking the NAND tree output to ensure there is a toggle high-to-low or low-to-high for each NAND tree input driven low The following tables list the NAND tree pin order. July 2010 30 M9999-070910-1.0 Micrel, Inc. NAND Tree Description Input Input Input Input Input Input Input Input Input Input Input Input Input Input Input Input Input Input Input Output KSZ8051MNL/RNL Pin Number 11 12 13 14 15 16 18 19 20 21 22 23 24 25 26 27 30 31 28 29 Pin Name MDIO MDC RXD3 RXD2 RXD1 RXD0 RXDV RXC RXER INTRP TXC TXEN TXD0 TXD1 TXD2 TXD3 LED0 LED1 COL CRS Table 7. NAND Tree Test Pin Order – for KSZ8051MNL NAND Tree Description Input Input Input Input Input Input Input Input Input Input Input Input Input Input Input Input Output Pin Number 11 12 13 14 15 16 18 19 20 21 23 24 25 30 31 28 29 Pin Name MDIO MDC PHYAD0 PHYAD1 RXD1 RXD0 CRS_DV REF_CLK RXER INTRP TXEN TXD0 TXD1 LED0 LED1 CONFIG0 CONFIG1 Table 8. NAND Tree Test Pin Order – for KSZ8051RNL July 2010 31 M9999-070910-1.0 Micrel, Inc. KSZ8051MNL/RNL NAND Tree I/O Testing The following procedure can be used to check for faults on the KSZ8051MNL/RNL digital I/O pin connections to the board: 1. Enable NAND tree mode by either hardware pin strapping (NAND_Tree#, pin 21) or software (register 16h, bit 5). 2. Use board logic to drive all KSZ8051MNL/RNL NAND tree input pins high. 3. Use board logic to drive each NAND tree input pin, per KSZ8051MNL/RNL NAND Tree pin order, as follow: a. Toggle the first pin (MDIO) from high to low, and verify the CRS/CONFIG1 pin switch from low to high to indicate that the first pin is connected properly. b. Leave the first pin (MDIO) low. c. Toggle the second pin (MDC) from high to low, and verify the CRS/CONFIG1 pin switch from high to low to indicate that the second pin is connected properly. d. Leave the first pin (MDIO) and the second pin (MDC) low. e. Toggle the third pin from high to low, and verify the CRS/CONFIG1 pin switch from low to high to indicate that the third pin is connected properly. f. Continue with this sequence until all KSZ8051MNL/RNL NAND tree input pins have been toggled. Each KSZ8051MNL/RNL NAND tree input pin must cause the CRS/CONFIG1 output pin to toggle high-to-low or low-tohigh to indicate a good connection. If the CRS/CONFIG1 pin fails to toggle when the KSZ8051MNL/RNL input pin toggles from high to low, the input pin has a fault. Power Management The KSZ8051MNL/RNL offers the following power management modes: Power Saving Mode Power Saving Mode is used to reduce the transceiver power consumption when the cable is unplugged. It is enabled by writing a one to register 1Fh, bit 10, and is in effect when auto-negotiation mode is enabled and cable is disconnected (no link). In this mode, the KSZ8051MNL/RNL shuts down all transceiver blocks, except for transmitter, energy detect and PLL circuits. By default, Power Saving Mode is disabled after power-up. Energy Detect Power Down Mode Energy Detect Power Down Mode is used to further reduce the transceiver power consumption when the cable is unplugged. It is enabled by writing a zero to register 18h, bit 11, and is in effect when auto-negotiation mode is enabled and cable is disconnected (no link). In this mode, the KSZ8051MNL/RNL shuts down all transceiver blocks, except for transmitter and energy detect circuits. Further power consumption is achieved by extending the time interval in between transmissions of link pulses to check for the presence of a link partner. The periodic transmission of link pulses is needed to ensure two link partners in the same low power state and with auto MDI/MDI-X disabled can wake up when the cable is connected between them. By default, Energy Detect Power Down Mode is disabled after power-up. Power Down Mode Power Down Mode is used to power down the KSZ8051MNL/RNL device when it is not in use after power-up. It is enabled by writing a one to register 0h, bit 11. In this mode, the KSZ8051MNL/RNL disables all internal functions, except for the MII management interface. The KSZ8051MNL/RNL exits (disables) Power Down Mode after register 0h, bit 11 is set back to zero. Slow Oscillator Mode Slow Oscillator Mode is used to disconnect the input reference crystal/clock on XI (pin 9) and select the on-chip slow oscillator when the KSZ8051MNL/RNL device is not in use after power-up. It is enabled by writing a one to register 11h, bit 5. Slow Oscillator Mode works in conjunction with Power Down Mode to put the KSZ8051MNL/RNL device in the lowest July 2010 32 M9999-070910-1.0 Micrel, Inc. KSZ8051MNL/RNL power state with all internal functions disabled, except for the MII management interface. To properly exit this mode and return to normal PHY operation, use the following programming sequence: 1. Disable Slow Oscillator Mode by writing a zero to register 11h, bit 5. 2. Disable Power Down Mode by writing a zero to register 0h, bit 11. 3. Initiate software reset by writing a one to register 0h, bit 15. Reference Circuit for Power and Ground Connections The KSZ8051MNL/RNL is a single 3.3V supply device with a built-in regulator to supply the 1.2V core. The power and ground connections are shown in the following figure and table for 3.3V VDDIO. Figure 8. KSZ8051MNL/RNL Power and Ground Connections Power Pin VDD_1.2 VDDA_3.3 VDDIO Pin Number 2 3 17 Description Decouple with 2.2uF and 0.1uF capacitors-to-ground. Connect to board’s 3.3V supply through ferrite bead. Decouple with 22uF and 0.1uF capacitors-to-ground. Connect to board’s 3.3V supply for 3.3V VDDIO. Decouple with 22uF and 0.1uF capacitors-to-ground. Table 9. KSZ8051MNL/RNL Power Pin Description July 2010 33 M9999-070910-1.0 Micrel, Inc. KSZ8051MNL/RNL Register Map Register Number (Hex) 0h 1h 2h 3h 4h 5h 6h 7h 8h 9h – 10h 11h 12h – 14h 15h 16h 17h 18h 19h – 1Ah 1Bh 1Ch 1Dh 1Eh 1Fh Description Basic Control Basic Status PHY Identifier 1 PHY Identifier 2 Auto-Negotiation Advertisement Auto-Negotiation Link Partner Ability Auto-Negotiation Expansion Auto-Negotiation Next Page Link Partner Next Page Ability Reserved AFE Control 1 Reserved RXER Counter Operation Mode Strap Override Operation Mode Strap Status Expanded Control Reserved Interrupt Control/Status Reserved LinkMD® Control/Status PHY Control 1 PHY Control 2 Register Description Address Name Description Mode (1) Default Register 0h – Basic Control 0.15 Reset 1 = Software reset 0 = Normal operation This bit is self-cleared after a ‘1’ is written to it. 0.14 0.13 Loop-back Speed Select 1 = Loop-back mode 0 = Normal operation 1 = 100Mbps 0 = 10Mbps This bit is ignored if auto-negotiation is enabled (register 0.12 = 1). 0.12 AutoNegotiation Enable 1 = Enable auto-negotiation process 0 = Disable auto-negotiation process If enabled, auto-negotiation result overrides settings in register 0.13 and 0.8. RW RW Set by SPEED strapping pin. See “Strapping Options” section for details. Set by NWAYEN strapping pin. See “Strapping Options” section for details. RW 0 RW/SC 0 July 2010 34 M9999-070910-1.0 Micrel, Inc. KSZ8051MNL/RNL Register Description (Continued) Address Name Description Mode (1) Default Register 0h – Basic Control 0.11 Power Down 1 = Power down mode 0 = Normal operation If software reset (register 0.15) is used to exit Power Down mode (register 0.11 = 1), two software reset writes (register 0.15 = 1) are required. First write clears Power Down mode; second write resets chip and re-latches the pin strapping pin values. 0.10 Isolate 1 = Electrical isolation of PHY from MII 0 = Normal operation 0.9 Restart AutoNegotiation 1 = Restart auto-negotiation process 0 = Normal operation. This bit is self-cleared after a ‘1’ is written to it. 0.8 Duplex Mode 1 = Full-duplex 0 = Half-duplex RW Inverse of DUPLEX strapping pin value. See “Strapping Options” section for details. 0.7 0.6:0 Collision Test Reserved 1 = Enable COL test 0 = Disable COL test RO 000_0000 RW 0 RW/SC RW Set by ISO strapping pin. See “Strapping Options” section for details. 0 RW 0 Register 1h – Basic Status 1.15 1.14 1.13 1.12 1.11 1.10:7 1.6 1.5 100Base-T4 100Base-TX Full Duplex 100Base-TX Half Duplex 10Base-T Full Duplex 10Base-T Half Duplex Reserved No Preamble AutoNegotiation Complete Remote Fault AutoNegotiation Ability 1 = Preamble suppression 0 = Normal preamble 1 = Auto-negotiation process completed 0 = Auto-negotiation process not completed 1 = Remote fault 0 = No remote fault 1.3 1 = Capable to perform auto-negotiation 0 = Not capable to perform auto-negotiation RO 1 RO/LH 0 RO 0 1 = T4 capable 0 = Not T4 capable 1 = Capable of 100Mbps full-duplex 0 = Not capable of 100Mbps full-duplex 1 = Capable of 100Mbps half-duplex 0 = Not capable of 100Mbps half-duplex 1 = Capable of 10Mbps full-duplex 0 = Not capable of 10Mbps full-duplex 1 = Capable of 10Mbps half-duplex 0 = Not capable of 10Mbps half-duplex RO RO 0000 1 RO 1 RO 1 RO 1 RO 1 RO 0 1.4 July 2010 35 M9999-070910-1.0 Micrel, Inc. KSZ8051MNL/RNL Register Description (Continued) Address 1.2 1.1 1.0 Name Link Status Jabber Detect Extended Capability Description 1 = Link is up 0 = Link is down 1 = Jabber detected 0 = Jabber not detected (default is low) 1 = Supports extended capabilities registers RO 1 RO/LH 0 Mode (1) Default 0 RO/LL Register 2h – PHY Identifier 1 2.15:0 PHY ID Number Assigned to the 3rd through 18th bits of the Organizationally Unique Identifier (OUI). Kendin Communication’s OUI is 0010A1 (hex) RO 0022h Register 3h – PHY Identifier 2 3.15:10 PHY ID Number Model Number Revision Number Assigned to the 19th through 24th bits of the Organizationally Unique Identifier (OUI). Kendin Communication’s OUI is 0010A1 (hex) Six bit manufacturer’s model number Four bit manufacturer’s revision number RO 0001_01 3.9:4 3.3:0 RO RO 01_0101 Indicates silicon revision Register 4h – Auto-Negotiation Advertisement 4.15 4.14 4.13 4.12 4.11:10 Next Page Reserved Remote Fault Reserved Pause [00] = No PAUSE [10] = Asymmetric PAUSE [01] = Symmetric PAUSE [11] = Asymmetric & Symmetric PAUSE 4.9 4.8 100Base-T4 100Base-TX Full-Duplex 100Base-TX Half-Duplex 10Base-T Full-Duplex 10Base-T Half-Duplex Selector Field 1 = T4 capable 0 = No T4 capability 1 = 100Mbps full-duplex capable 0 = No 100Mbps full-duplex capability 1 = 100Mbps half-duplex capable 0 = No 100Mbps half-duplex capability 1 = 10Mbps full-duplex capable 0 = No 10Mbps full-duplex capability 1 = 10Mbps half-duplex capable 0 = No 10Mbps half-duplex capability [00001] = IEEE 802.3 RW 0_0001 RW 1 RW RW RW Set by SPEED strapping pin. See “Strapping Options” section for details. Set by SPEED strapping pin. See “Strapping Options” section for details. 1 RO 0 1 = Remote fault supported 0 = No remote fault RO RW 0 00 1 = Next page capable 0 = No next page capability. RO RW 0 0 RW 0 4.7 4.6 4.5 4.4:0 July 2010 36 M9999-070910-1.0 Micrel, Inc. KSZ8051MNL/RNL Register Description (Continued) Address Name Description Mode (1) Default Register 5h – Auto-Negotiation Link Partner Ability 5.15 5.14 5.13 5.12 5.11:10 Next Page Acknowledge Remote Fault Reserved Pause [00] = No PAUSE [10] = Asymmetric PAUSE [01] = Symmetric PAUSE [11] = Asymmetric & Symmetric PAUSE 5.9 5.8 5.7 5.6 5.5 5.4:0 100Base-T4 100Base-TX Full-Duplex 100Base-TX Half-Duplex 10Base-T Full-Duplex 10Base-T Half-Duplex Selector Field 1 = T4 capable 0 = No T4 capability 1 = 100Mbps full-duplex capable 0 = No 100Mbps full-duplex capability 1 = 100Mbps half-duplex capable 0 = No 100Mbps half-duplex capability 1 = 10Mbps full-duplex capable 0 = No 10Mbps full-duplex capability 1 = 10Mbps half-duplex capable 0 = No 10Mbps half-duplex capability [00001] = IEEE 802.3 RO 0_0001 RO 0 RO 0 RO 0 RO 0 RO 0 1 = Next page capable 0 = No next page capability 1 = Link code word received from partner 0 = Link code word not yet received 1 = Remote fault detected 0 = No remote fault RO RO 0 00 RO 0 RO 0 RO 0 Register 6h – Auto-Negotiation Expansion 6.15:5 6.4 6.3 Reserved Parallel Detection Fault Link Partner Next Page Able Next Page Able Page Received Link Partner AutoNegotiation Able 1 = Fault detected by parallel detection 0 = No fault detected by parallel detection 1 = Link partner has next page capability 0 = Link partner does not have next page capability 1 = Local device has next page capability 0 = Local device does not have next page capability 1 = New page received 0 = New page not received yet 6.0 1 = Link partner has auto-negotiation capability 0 = Link partner does not have auto-negotiation capability RO 0 RO/LH 0 RO 1 RO 0 RO RO/LH 0000_0000_000 0 6.2 6.1 July 2010 37 M9999-070910-1.0 Micrel, Inc. KSZ8051MNL/RNL Register Description (Continued) Address Name Description Mode (1) Default Register 7h – Auto-Negotiation Next Page 7.15 7.14 7.13 7.12 7.11 Next Page Reserved Message Page Acknowledge2 Toggle 1 = Message page 0 = Unformatted page 1 = Will comply with message 0 = Cannot comply with message 1 = Previous value of the transmitted link code word equaled logic one 0 = Logic zero 7.10:0 Message Field 11-bit wide field to encode 2048 messages RW 000_0000_0001 RO 0 RW 0 1 = Additional next page(s) will follow 0 = Last page RO RW 0 1 RW 0 Register 8h – Link Partner Next Page Ability 8.15 8.14 8.13 8.12 8.11 Next Page Acknowledge Message Page Acknowledge2 Toggle 1 = Additional Next Page(s) will follow 0 = Last page 1 = Successful receipt of link word 0 = No successful receipt of link word 1 = Message page 0 = Unformatted page 1 = Able to act on the information 0 = Not able to act on the information 1 = Previous value of transmitted link code word equal to logic zero 0 = Previous value of transmitted link code word equal to logic one 8.10:0 Message Field RO 000_0000_0000 RO 0 RO 0 RO 0 RO 0 RO 0 Register 11h – AFE Control 1 11.15:6 11.5 Reserved Slow Oscillator Mode Enable Slow Oscillator Mode is used to disconnect the input reference crystal/clock on the XI pin and select the on-chip slow oscillator when the KSZ8051 device is not in use after power-up. 1 = Enable 0 = Disable This bit automatically sets software power down to the analog side when enabled. 11.4:0 Reserved RW 0_0000 RW RW 0000_0000_00 0 Register 15h – RXER Counter 15.15:0 RXER Counter Receive error counter for Symbol Error frames RO/SC 0000h July 2010 38 M9999-070910-1.0 Micrel, Inc. KSZ8051MNL/RNL Register Description (Continued) Address Name Description Mode (1) Default Register 16h – Operation Mode Strap Override 16.15:11 16.10 16.9 16.8 16.7 Reserved Reserved B-CAST_OFF override Reserved MII B-to-B override RMII B-to-B override NAND Tree override Reserved RMII override MII override 1 = Override strap-in for RMII mode This bit is applicable for KSZ8051RNL only. 16.0 1 = Override strap-in for MII mode This bit is applicable for KSZ8051MNL only. Register 17h – Operation Mode Strap Status 17.15:13 PHYAD[2:0] strap-in status [000] = Strap to PHY Address 0 [001] = Strap to PHY Address 1 [010] = Strap to PHY Address 2 [011] = Strap to PHY Address 3 [100] = Strap to PHY Address 4 [101] = Strap to PHY Address 5 [110] = Strap to PHY Address 6 [111] = Strap to PHY Address 7 17.12:10 17.9 17.8 17.7 17.6 17.5 17.4:2 17.1 17.0 Reserved B-CAST_OFF strap-in status Reserved MII B-to-B strap-in status RMII B-to-B strap-in status NAND Tree strap-in status Reserved RMII strap-in status MII strap-in status 1 = Strap to RMII mode This bit is applicable for KSZ8051RNL only. 1 = Strap to MII mode This bit is applicable for KSZ8051MNL only. RO 1 = Strap to MII Back-to-Back mode This bit is applicable for KSZ8051MNL only. 1 = Strap to RMII Back-to-Back mode This bit is applicable for KSZ8051RNL only. 1 = Strap to NAND Tree mode RO RO RO RO 1 = Strap to B-CAST_OFF If bit is ‘1’, PHY Address 0 is non-broadcast. RO RO RO RO RO RW 1 1 = Override strap-in for MII Back-to-Back mode (set also bit 0 of this register to 1) This bit is applicable for KSZ8051MNL only. 16.6 1 = Override strap-in for RMII Back-to-Back mode (set also bit 1 of this register to 1) This bit is applicable for KSZ8051RNL only. 16.5 16.4:2 16.1 1 = Override strap-in for NAND Tree mode RW RW RW 0 000 0 RW 0 1 = Override strap-in for B-CAST_OFF If bit is ‘1’, PHY Address 0 is non-broadcast. RW RW 0 0 RW RO RW 0000_0 0 0 July 2010 39 M9999-070910-1.0 Micrel, Inc. KSZ8051MNL/RNL Register Description (Continued) Address Name Description Mode (1) Default Register 18h – Expanded Control 18.15:12 18.11 Reserved EDPD Disabled Energy Detect Power Down mode 1 = Disable 0 = Enable 18.10 100Base-TX Preamble Restore 1 = Restore received preamble to MII output (random latency) 0 = Consume 1-byte preamble before sending frame to MII output for fixed latency This bit is applicable for KSZ8051MNL only. 18.9:7 18.6 Reserved 10Base-T Preamble Restore 1 = Restore received preamble to MII output 0 = Remove all 7-bytes of preamble before sending frame (starting with SFD) to MII output This bit is applicable for KSZ8051MNL only. 18.5:0 Reserved RW 00_0000 RW RW 000 0 RW 0 RW RW 0000 1 Register 1Bh – Interrupt Control/Status 1b.15 Jabber Interrupt Enable Receive Error Interrupt Enable Page Received Interrupt Enable Parallel Detect Fault Interrupt Enable Link Partner Acknowledge Interrupt Enable Link Down Interrupt Enable Remote Fault Interrupt Enable Link Up Interrupt Enable Jabber Interrupt Receive Error Interrupt 1 = Enable Jabber Interrupt 0 = Disable Jabber Interrupt 1 = Enable Receive Error Interrupt 0 = Disable Receive Error Interrupt 1 = Enable Page Received Interrupt 0 = Disable Page Received Interrupt 1 = Enable Parallel Detect Fault Interrupt 0 = Disable Parallel Detect Fault Interrupt 1 = Enable Link Partner Acknowledge Interrupt 0 = Disable Link Partner Acknowledge Interrupt 1= Enable Link Down Interrupt 0 = Disable Link Down Interrupt 1 = Enable Remote Fault Interrupt 0 = Disable Remote Fault Interrupt 1 = Enable Link Up Interrupt 0 = Disable Link Up Interrupt 1 = Jabber occurred 0 = Jabber did not occurred 1 = Receive Error occurred 0 = Receive Error did not occurred RO/SC 0 RO/SC 0 RW 0 RW 0 RW 0 RW 0 RW 0 RW 0 RW 0 RW 0 1b.14 1b.13 1b.12 1b.11 1b.10 1b.9 1b.8 1b.7 1b.6 July 2010 40 M9999-070910-1.0 Micrel, Inc. KSZ8051MNL/RNL Register Description (Continued) Address 1b.5 1b.4 1b.3 Name Page Receive Interrupt Parallel Detect Fault Interrupt Link Partner Acknowledge Interrupt Link Down Interrupt Remote Fault Interrupt Link Up Interrupt ® Description 1 = Page Receive occurred 0 = Page Receive did not occur 1 = Parallel Detect Fault occurred 0 = Parallel Detect Fault did not occur 1 = Link Partner Acknowledge occurred 0 = Link Partner Acknowledge did not occur 1 = Link Down occurred 0 = Link Down did not occur 1 = Remote Fault occurred 0 = Remote Fault did not occur 1 = Link Up occurred 0 = Link Up did not occur Mode (1) Default 0 0 0 RO/SC RO/SC RO/SC 1b.2 1b.1 1b.0 RO/SC RO/SC RO/SC 0 0 0 Register 1Dh – LinkMD Control/Status 1d.15 Cable Diagnostic Test Enable 1 = Enable cable diagnostic test. After test has completed, this bit is self-cleared. 0 = Indicates cable diagnostic test (if enabled) has completed and the status information is valid for read. [00] = normal condition [01] = open condition has been detected in cable [10] = short condition has been detected in cable [11] = cable diagnostic test has failed 1d.12 1d.11:9 1d.8:0 Short Cable Indicator Reserved Cable Fault Counter Distance to fault 1 = Short cable (
KSZ8051MNL 价格&库存

很抱歉,暂时无法提供与“KSZ8051MNL”相匹配的价格&库存,您可以联系我们找货

免费人工找货