LX2203
TM ®
Li-Ion Battery Charger
P RODUCTION D ATA S HEET
DESCRIPTION
KEY FEATURES Up to 1A charge current Low drop out design Reverse leakage protection Linear thermal control loop Pre-charge conditioning Programmable Termination Current Short Circuit protected Small 3x3mm MLP package
APPLICATIONS
The LX2203 is a tiny linear battery charger for Lithium Ion or Lithium Polymer batteries. The LX2203 includes built in MOSFET, accurate current and voltage regulation, reverse blocking protection, over temperature control, and charge status indicator. The accurate programmable charge current and independent termination current programming make it easy to logically reprogram the charge current limit at any time.
The LX2203 charges the battery in two phases: constant current and constant voltage. A reduced current conditioning mode is provided for deeply discharged batteries. The LX2203 automatically restarts if the battery voltage falls below the top-off threshold. The LX2203 enters a low quiescent current sleep mode when power is removed.
W WW . Microsemi . C OM
IMPORTANT: For the most current data, consult MICROSEMI’s website: http://www.microsemi.com
PDAs, MP3 Players Cell Phones Charging cradles Digital Cameras
PRODUCT HIGHLIGHT
AC/DC Adapter
VIN VIN STAT CTP GND
BAT BAT
LX2203
CMP EN CCP
+
EN 0 1
MODE Sleep mode – charge disabled Charge enabled.
ON/OFF
PACKAGE ORDER INFO
_
LX2203 LX2203
TA (°C) -40 to 85
LD
Plastic MLP 10-Pin
RoHS Compliant / Pb-free
LX2203CLD
Note: Available in Tape & Reel. Append the letters “TR” to the part number. (i.e. LX2203CLD-TR)
Copyright © 2004 Rev. 1.0a, 2005-08-10
Microsemi
Integrated Products Division 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
Page 1
LX2203
TM ®
Li-Ion Battery Charger
P RODUCTION D ATA S HEET
ABSOLUTE MAXIMUM RATINGS Supply Voltage (VIN)....................................................................................... -0.3V to 7V Input Signals (SHDN, EN,CMP) ...................................................................... -0.3V to 7V Battery Charging Current (IBAT)....................................................................................1.2A Operating Junction Temperature................................................................... -40C to 150°C Storage Temperature Range.........................................................................-65°C to 150°C
RoHS / Pb-free Peak Package Solder Reflow Temp(40 seconds max. exposure) ............260°C (+0 -5) Note: Exceeding these ratings could cause damage to the device. All voltages are with respect to Ground. Currents are positive into, negative out of specified terminal.
PACKAGE PIN OUT
W WW . Microsemi . C OM
VIN VIN STAT CTP GND
1
10
BAT BAT CMP EN CCP
2
9
3
8
4
Connect Bottom to Power GND
7
5
6
THERMAL DATA
LD PACKAGE
(Top View)
RoHS / Pb-free 100% Matte Tin Lead Finish
LD
Plastic Micro Leadframe Package 10-Pin THERMAL RESISTANCE-JUNCTION TO AMBIENT, θJA
49°C/W
Junction Temperature Calculation: TJ = TA + (PD x θJA). The θJA numbers are guidelines for the thermal performance of the device/pc-board system. All of the above assume no ambient airflow.
FUNCTIONAL PIN DESCRIPTION Name BAT CCP CMP CTP EN GND STAT VIN Description Charging Output - This pin is wired to the positive terminal of the battery. (The negative battery terminal is wired to GND.) Charge Current Programming Pin - A resistor (Rccp) is connected between this pin and GND. See application section for programming information. Compensation Pin – Apply a 0.01µF capacitor between CMP and VIN pins. Charge Termination Programming Pin – A resistor (Rctp) is connected between this pin and GND See application section for programming information. Enable - Applying a TTL compatible Hi signal enables the charger, a Low signal disables the charger and puts it in sleep mode. Common Ground. Status - This pin is a logic low level when the battery is being charged. Pin can sink up to 5mA.
PACKAGE DATA PACKAGE DATA
Voltage Input – Supply Voltage. Must be greater than VBAT to charge.
Copyright © 2004 Rev. 1.0a, 2005-08-10
Microsemi
Integrated Products Division 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
Page 2
LX2203
TM ®
Li-Ion Battery Charger
P RODUCTION D ATA S HEET
Unless otherwise specified, the following specifications apply over the ambient temperature 0°C ≤ TA noted and the following test conditions: VVIN = 5V, VBAT =3.8V, Rccp = 90.9k, Rctp = 150k. Parameter
MAIN CIRCUITRY Input Voltage Quiescent Current CTP Bias Voltage CCP Bias Voltage CONSTANT VOLTAGE MODE BAT Output Voltage Top Off Charge Droop Threshold Charge Termination Taper Current CONSTANT CURRENT MODE BAT Constant Current Conditioning Current Conditioning Current Mode Threshold Voltage LOGIC STAT Logic High Output STAT Logic Low Output EN Select Threshold EN bias current THERMAL SHUTDOWN Maximum Junction Temperature PASS ELEMENT Reverse mode current UNDER VOLTAGE LOCKOUT Rising Threshold Voltage Falling Threshold Voltage VUVLO+ VUVLO-IBAT VVIN < VBAT TJ VSTAT VSTAT VEN IEN ISTAT = -100uA ISTAT = 5mA Logic Hi Logic Lo VEN = Hi ICOND VBAT(COND) VBAT < VBAT(COND) VBAT(COND) /VBAT(MAX) VBAT(MAX) VDRP VDRP /VBAT(MAX) VBAT = VBAT(MAX) VVIN IGND VCTP VCCP VEN = Hi VEN = Lo
ELECTRICAL CHARACTERISTICS
≤
70°C except where otherwise
W WW . Microsemi . C OM
Symbol
Test Conditions
Min
4.35
LX2203 Typ
Max
6
Units
V mA µA V V
3 7 1.25 1.25
5
4.16 96 42
4.2 97 51
4.24 98 60
V % mA
0.9 4% 60
1.0 5% 63
1.1 6% 66
A
ICOND IBAT
%
4.5 0.5 2.0 0.8 8
V V
µA °C
150
5
µA
4.2 3.9
V V
ELECTRICALS ELECTRICALS
Copyright © 2004 Rev. 1.0a, 2005-08-10
Microsemi
Integrated Products Division 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
Page 3
LX2203
TM ®
Li-Ion Battery Charger
P RODUCTION D ATA S HEET
CHARGING PROFILE
4.5
CHARGE CURRENT PROGRAMMING
W WW . Microsemi . C OM
Charge Voltage And Current
4.0
1200
Charge Current (mA)
3.5 Voltage 3.0 2.5 2.0 1.5 1.0 Current
1000 800 600 400 200 0
0.5 0 0 0.5 1.0 1.5 2.0 2.5
0
4.0
8.0
12.0
16.0
Iccp Current (µA)
Constant Charge Current Programming CHARGE VOLTAGE DISTRIBUTION
300
Charge Time (hours)
TERMINATION CURRENT PROGRAMMING
800
250 200
Termination Current (mA)
600
COUT
0 20 40 60 80 100
150 100
400
200
50
0
0 4.171 4.174 4.176 4.179 4.181 4.183 4.186 4.188 4.191 4.193 4.196 4.198 4.201 4.203 4.206 4.208 4.210 4.213 4.215 4.218 4.220 4.223 4.225 4.228 4.230
1/Rctp (micromhos)
Termination Current Programming
V
Post Trim Bat Volt 1.0A CHARGE CURRENT DISTRIBUTION
70 60
50MA TERMINATION DISTRIBUTION
1400 1200 1000 Count
50
Count
40
800 600
30
CHARTS CHARTS
20
400
10
200
0 -996.327E-03 -989.388E-03 -982.449E-03 -975.510E-03 -968.571E-03 -961.633E-03 -954.694E-03 -947.755E-03 -940.816E-03 -933.878E-03 -926.939E-03 -920.000E-03 -1.087 -1.080 -1.073 -1.066 -1.059 -1.052 -1.045 -1.038 -1.031 -1.024 -1.017 -1.010 -1.003
0 -60 -56 -52 -48 -44 -40 -36 -32 -28 -24 -20 More
A
Charge Current Post Trim
Copyright © 2004 Rev. 1.0a, 2005-08-10
mA
Microsemi
Integrated Products Division 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
Page 4
LX2203
TM ®
Li-Ion Battery Charger
P RODUCTION D ATA S HEET
SIMPLIFIED BLOCK DIAGRAM
W WW . Microsemi . C OM
+ EN ENABLE
UVLO
VDD
STAT CHARGE CONTROL BAT
CHARGE TERMINATION CONTROL
CTP
CMP
CONSTANT VOLTAGE CONTROL
TEMPERATURE CONTROL
CCP
CONSTANT CURRENT CONTROL
GND
BLOCK DIAGRAM BLOCK DIAGRAM
Figure 1 – Simplified Block Diagram
Copyright © 2004 Rev. 1.0a, 2005-08-10
Microsemi
Integrated Products Division 11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
Page 5
LX2203
TM ®
Li-Ion Battery Charger
P RODUCTION D ATA S HEET
THEORY OF OPERATION
W WW . Microsemi . C OM
LX2203 CONTROL FLOW DIAGRAM
Return to START if EN changes state or VIN is removed.
S TART
EN = 1
YES
NO
SLEEP
V IN > V UVLO
YES
NO
V IN > V BAT
YES
NO
CONSTANT VOLTAGE CHARGE MODE
NO
V BAT >60%
YES
CONDITION CHARGE MODE
TEMP <
1 50
YES
NO
REDUCE CHARGE CURRENT
CONSTANT CURRENT CHARGE MODE
NO
I BAT V CV
YES
V BAT
很抱歉,暂时无法提供与“LX2203CLD”相匹配的价格&库存,您可以联系我们找货
免费人工找货