MPIC2117D

MOTOROLA SEMICONDUCTOR TECHNICAL DATA Order this document by MPIC2117/D Power Products Division Advance Information SINGLE CHANNEL DRIVER The MPIC2117 is a high voltage, high speed, power MOSFET and IGBT driver. Proprietary HVIC and latch immune CMOS technologies enable ruggedized monolithic construction. The logic input is compatible with standard CMOS outputs. The output drivers feature a high pulse current buffer stage designed for minimum driver cross–conduction. The floating channel can be used to drive an N–channel power MOSFET or IGBT in the high side or low side configuration which operates from 10 to 600 volts. MPIC2117 SINGLE CHANNEL DRIVER • • • • • • • • Floating Channel Designed for Bootstrap Operation Fully Operational to +600 V Tolerant to Negative Transient Voltage dV/dt Immune Gate Drive Supply Range from 10 to 20 V Undervoltage Lockout CMOS Schmitt–triggered Input with Pull–down Output In Phase with Input P SUFFIX PLASTIC PACKAGE CASE 626–05 8 1 PRODUCT SUMMARY VOFFSET IO+/– VOUT ton/off (typical) 600 V MAX 200 mA/420 mA 10 – 20 V 125 & 105 ns D SUFFIX PLASTIC PACKAGE CASE 751–05 (SO–8) 8 1 ORDERING INFORMATION Device MPIC2117D MPIC2117P Package SOIC PDIP PIN CONNECTIONS (TOP VIEW) VCC 1 IN 2 COM 3 4 8 LEADS DIP MPIC2117P 8 VB 7 HO 6 VS 5 VCC 1 IN 2 COM 3 4 8 LEAD SOIC MPIC2117D 8 VB 7 HO 6 VS 5 This document contains information on a new product. Specifications and information herein are subject to change without notice. REV 1 © Motorola Power Motorola, Inc. 1996 Products Division Advanced Data 1 MPIC2117 SIMPLIFIED BLOCK DIAGRAM VCC HV LEVEL SHIFT IN UV DETECT PULSE FILTER R R S Q VB HO PULSE GEN VS UV DETECT COM ABSOLUTE MAXIMUM RATINGS Absolute Maximum Ratings indicate sustained limits beyond which damage to the device may occur. All voltage parameters are absolute voltages referenced to COM. The Thermal Resistance and Power Dissipation ratings are measured under board mounted and still air conditions. Rating High Side Floating Supply Absolute Voltage High Side Floating Supply Offset Voltage High Side Floating Output Voltage Logic Supply Voltage Logic Input Voltage Allowable Offset Supply Voltage Transient *Package Power Dissipation @ TA ≤ +25°C Thermal Resistance, Junction to Ambient Operating and Storage Temperature Lead Temperature for Soldering Purposes, 10 seconds (8 Lead DIP) (8 Lead SOIC) (8 Lead DIP) (8 Lead SOIC) Symbol VB VS VHO VCC VIN dVS/dt PD – RθJA Tj, Tstg TL Min –0.3 VB–25 VS–0.3 –0.3 –0.3 – – – – – –55 – Max 625 VB+0.3 VB+0.3 25 VCC+0.3 50 1.0 0.625 125 200 150 260 Unit VDC V/ns Watt °C/W °C °C RECOMMENDED OPERATING CONDITIONS The Input/Output logic timing Diagram is shown in Figure 1. For proper operation the device should be used within the recommended conditions. The VS offset rating is tested with all supplies biased at 15 V differential. High Side Floating Supply Absolute Voltage High Side Floating Supply Offset Voltage High Side Floating Output Voltage Logic Supply Voltage Logic Input Voltage Ambient Temperature VB VS VHO VCC VIN TA VS+10 Note 1 VS 10 0 –40 VS+20 600 VB 20 VCC 125 °C V Note 1: Logic operational for VS of –5 to +600 V. Logic state held for VS of –5 V to –VBS. 2 Motorola Power Products Division Advanced Data MPIC2117 ELECTRICAL CHARACTERISTICS (TA = 25°C unless otherwise specified) Characteristic Symbol Min Typ Max Unit STATIC ELECTRICAL CHARACTERISTICS VBIAS (VCC, VBS) = 15 V unless otherwise specified. The VIN, VTH and IIN parameters are referenced to COM. The VO and IO parameters are referenced to COM and are applicable to the respective output leads: HO or LO. Logic “1” Input Voltage @ VCC = 10 V Logic “1” Input Voltage @ VCC = 15 V Logic “1” Input Voltage @ VCC = 20 V Logic “0” Input Voltage @ VCC = 10 V Logic “0” Input Voltage @ VCC = 15 V Logic “0” Input Voltage @ VCC = 20 V High Level Output Voltage, VBS–VO @ VIN = VIH, IO = 0 A Low Level Output Voltage, VO @ VIN = VIL, IO = 0 A Offset Supply Leakage Current @ VB = VS = 600 V Quiescent VBS Supply Current @ VIN = 0 V or VCC Quiescent VCC Supply Current @ VIN = 0 V or VCC Logic “1” Input Bias Current @ VIN = 15 V Logic “0” Input Bias Current @ VIN = 0 V VBS Supply Undervoltage Positive Going Threshold VBS Supply Undervoltage Negative Going Threshold VCC Supply Undervoltage Positive Going Threshold VCC Supply Undervoltage Negative Going Threshold Output High Short Circuit Pulsed Current @ VOUT = 0 V, VIN = 15 V, PW ≤ 10 µs Output Low Short Circuit Pulsed Current @ VOUT = 15 V, VIN = 0 V, PW ≤ 10 µs DYNAMIC ELECTRICAL CHARACTERISTICS VBIAS (VCC, VBS) = 15 V unless otherwise specified Turn–On Propagation Delay @ VS = 0 V Turn–Off Propagation Delay @ VS = 600 V Turn–On Rise Time @ CL = 1000 pF Turn–Off Fall Time @ CL = 1000 pF ton toff tr tf – – – – 125 105 80 40 – – – – ns VIH VIH VIH VIL VIL VIL VOH VOL ILK IQBS IQCC IIN+ IIN– VBSUV+ VBSUV– VCCUV+ VCCUV– IO+ IO– 6.4 9.5 12.6 – – – – – – – – – – – – – – 200 420 – – – – – – – – – 50 70 20 – 8.5 8.2 8.6 8.2 250 500 – – – 3.8 6.0 8.3 100 100 50 – – 40 1.0 – – – – – – mA V µA mV VDC TYPICAL CONNECTION VCC VCC IN COM VB HO VS IN Motorola Power Products Division Advanced Data 3 MPIC2117 LEAD DEFINITIONS Symbol VCC IN COM VB HO VS Logic Supply Logic Input for High Side Gate Driver Outputs (HO), In Phase with HO Logic Ground High Side Floating Supply High Side Gate Drive Output High Side Floating Supply Return Lead Description IN 50% IN ton tr 90% 50% tf 90% toff HO HO 10% 10% Figure 1. Input / Output Timing Diagram Figure 2. Switching Time Waveform Definitions 4 Motorola Power Products Division Advanced Data MPIC2117 PACKAGE DIMENSIONS NOTES: 1. DIMENSION L TO CENTER OF LEAD WHEN FORMED PARALLEL. 2. PACKAGE CONTOUR OPTIONAL (ROUND OR SQUARE CORNERS). 3. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. DIM A B C D F G H J K L M N MILLIMETERS MIN MAX 9.40 10.16 6.10 6.60 3.94 4.45 0.38 0.51 1.02 1.78 2.54 BSC 0.76 1.27 0.20 0.30 2.92 3.43 7.62 BSC ––– 10_ 0.76 1.01 INCHES MIN MAX 0.370 0.400 0.240 0.260 0.155 0.175 0.015 0.020 0.040 0.070 0.100 BSC 0.030 0.050 0.008 0.012 0.115 0.135 0.300 BSC ––– 10_ 0.030 0.040 8 5 –B– 1 4 F NOTE 2 –A– L C –T– SEATING PLANE J N D K M M H G 0.13 (0.005) TA M B M CASE 626–05 ISSUE K STYLE 1: PIN 1. 2. 3. 4. 5. 6. 7. 8. AC IN DC + IN DC – IN AC IN GROUND OUTPUT AUXILIARY VCC –A– B M 8 5 X 45 _ J 1 4 4X –B– M_ G F NOTES: 1. DIMENSIONS A AND B ARE DATUMS AND T IS A DATUM SURFACE. 2. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 3. DIMENSIONS ARE IN MILLIMETER. 4. DIMENSION A AND B DO NOT INCLUDE MOLD PROTRUSION. 5. MAXIMUM MOLD PROTRUSION 0.15 PER SIDE. 6. DIMENSION D DOES NOT INCLUDE MOLD PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. DIM A B C D F G J K M P R MILLIMETERS MIN MAX 4.80 5.00 3.80 4.00 1.35 1.75 0.35 0.49 0.40 1.25 1.27 BSC 0.18 0.25 0.10 0.25 0_ 7_ 5.80 6.20 0.25 0.50 P 0.25 (0.010) M –T– 8X C SEATING PLANE D 0.25 (0.010) M K TB S A S R CASE 751–05 ISSUE P Motorola Power Products Division Advanced Data 5 MPIC2117 Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA / EUROPE / Locations Not Listed: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447 or 602–303–5454 MFAX: RMFAX0@email.sps.mot.com – TOUCHTONE 602–244–6609 INTERNET: http://Design–NET.com JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, 6F Seibu–Butsuryu–Center, 3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–81–3521–8315 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298 6 ◊ Motorola Power Products Division Advanced Data *MPIC2117/D* MPIC2117/D