PCR1D331MCL1GS

CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS PCR Chip Type, High Reliability High reliability, High voltage (to 80V). Low ESR, High ripple current. Long life of 4000 hours at 125°C. SMD type : Lead free reflow soldering condition at 260°C peak complete correspondence. Compliant to the RoHS directive (2011/65/EU,(EU)2015/863). ESR after Endurance at -40°C. PCM AEC-Q200 compliant. Please contact us for details. PCH PCZ High Temperature Long Life High Capacitance Long Life Assurance PCR PCX Specifications Item Performance Characteristics Category Temperature Range – 55 to +125°C Rated Voltage Range 16 to 80V Rated Capacitance Range 22 to 1000µF Capacitance Tolerance ± 20% at 120Hz, 20°C Tangent of loss angle (tan δ) Less than or equal to the specified value at 120Hz, 20°C ESR ( 1) Less than or equal to the specified value at 100kHz, 20°C Leakage Current ( 2) After 2 minutes' application of rated voltage, leakage current is not more than 0.03CV or 3(µA), whichever is greater. 1.25 1.25 (100kHz) Temperature Characteristics (Max.Impedance Ratio) Z+125°C / Z+20°C Z– 55°C / Z+20°C Endurance The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 4000 hours at 125°C. Within ± 20% of initial capacitance value ( 3) 150% or less of the initial specified value 200% or less of the initial specified value Less than or equal to the initial specified value Capacitance change tan δ ESR ( 1) Leakage current ( 2) After storing the capacitors under no load at 125°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above. Shelf Life ESR after Endurance ( 1) Less than or equal to the specified value at 100kHz, -40°C Damp Heat (Steady State) The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 1000 hours at 85°C, 85% RH. Capacitance change tan δ ESR ( 1) Leakage current ( 2) Within ± 20% of initial capacitance value ( 3) 150% or less of the initial specified value 200% or less of the initial specified value Less than or equal to the initial specified value Resistance to Soldering Heat After soldering the capacitor under the soldering conditions prescribed here, the capacitor shall meet the specifications listed at right. Pre-heating shall be done at 150 to 200°C and for 60 to 180 sec. The duration for over +230°C temperature at capacitor surface shall not exceed 60 seconds. In case peak temperature is 260°C or less, reflow soldering shall be two times maximum. Measurement for solder temperature profile shall be made at the capacitor top. Capacitance change tan δ ESR ( 1) Leakage current ( 2) Within ± 10% of the initial capacitance value ( 3) 130% or less than the initial specified value 130% or less than the initial specified value Less than or equal to the initial specified value Marking Navy blue print on the case top 1 ESR should be measured at both of the terminal ends closest where the terminals protrude through the plastic platform. 2 Conditioning : If any doubt arises, measure the leakage current after the voltage treatment of applying DC rated voltage continuously to the capacitor for 120 minutes at 105°C. Type numbering system (Example : 35V 150µF) 3 Initial value : The value before test of examination of resistance to soldering. 1 Dimensions Positive Standard Lot No. 0.3 MAX. 3 4 5 6 7 8 9 10 11 12 13 14 Taping code 0.5 MAX. Capacitance Plastic platform 2 PCR 1 V 1 5 1 MC L 1 GS C±0.2 Size code Configuration Capacitance tolerance (±20%) A±0.2 E Negative H Positive Plastic platform B±0.2 C±0.2 A±0.2 0.3 MAX. φD±0.5 CR 150 V 331 Lot No. Rated voltage (35V) Series name Standard (mm) Size φ8 × 7L φ8 × 10L φ8 × 12L φ10 × 8L φ10 ×10L φ10×12.7L φD 8.0 8.0 8.0 10.0 10.0 10.0 Voltage (V:35V) L±0.5 H Negative Dimension table in next page. Size φ8 ×10.5L φ10×10.5L φ10 ×13.2L φD 8.0 10.0 10.0 L 6.9 9.9 11.9 7.9 9.9 12.6 L 10.0 10.0 9.0 9.0 9.0 11.0 11.0 11.0 A 9.0 11.0 11.0 B 8.3 8.3 8.3 10.3 10.3 10.3 B 8.3 10.3 10.3 C 8.3 8.3 8.3 10.3 10.3 10.3 C 8.3 10.3 10.3 E 3.2 3.2 3.2 4.6 4.6 4.6 E 3.1 4.6 4.6 H 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 0.8 to 1.1 V H 12.7 1.1 to 1.5 1.1 to 1.5 1.1 to 1.5 Frequency coefficient of rated ripple current 16 20 25 35 50 63 80 Code C Aid electrode Vibration Resistance (mm) A Voltage Series Configuration Code Standard L Vibration Resistance S Type 0.5 MAX. Vibration Resistance Capacitance L +0.1 -0.4 E Voltage (V:35V) Series B±0.2 φD±0.5 CR 150 V 331 Rated capacitance (150µF) D E V H J K Frequency 120Hz 1kHz­ 10kHz 100kHz or more Coefficient 0.05 0.30 0.70 1.00 φ8×10L(φ8×10.5L), φ10×10L(φ10×10.5L), φ10×12.7L(φ10×13.2L) : The vibration structure-resistant product is also available upon request, please ask for details. ( ) : Size of the vibration structure-resistant product. CAT.8100K CONDUCTIVE POLYMER ALUMINUM SOLID ELECTROLYTIC CAPACITORS PCR Dimensions Rated Voltage （V） （code） 16 （1C） Surge Voltage (V) 20 Case Size φD×L（mm） tan δ 220 8× 7 0.08 105 30 60 1500 PCR1C221MCL1GS 470 ▲ 8× 10 0.08 225 17 34 3400 PCR1C471MCL6GS 470 10× 8 0.08 225 32 64 2200 PCR1C471MCL1GS 25 （1E） 35 （1V） 50 （1H） 63 （1J） 80 （1K） 25 31 43 63 79 100 （ ） Part Number 560 8× 12 0.08 268 16 32 3800 PCR1C561MCL1GS 680 10× 10 0.08 326 19 38 3200 PCR1C681MCL1GS 10×12.7 0.08 480 13 26 4300 PCR1C102MCL1GS 1000 20 （1D） Low temp. Leakage Current Initial Rated Ripple ESR after （µA） Endurance （mArms） ESR (mΩ) (mΩ) at 20℃ after （20℃/100kHz） （125℃ /100kHz） 2 minutes （−40℃ /100kHz） Rated Capacitance （µF） 150 8×7 0.08 90 39 78 1200 PCR1D151MCL1GS 330 ▲ 8× 10 0.08 198 19 38 3300 PCR1D331MCL6GS 330 10× 8 0.08 198 33 66 2100 PCR1D331MCL1GS 470 8× 12 0.08 282 18 36 3500 PCR1D471MCL1GS 560 10× 10 0.08 336 20 40 3100 PCR1D561MCL1GS 680 10× 12.7 0.08 408 14 28 4200 PCR1D681MCL1GS 100 8 ×7 0.08 75 41 82 1200 PCR1E101MCL1GS 220 ▲ 8× 10 0.08 165 20 40 3200 PCR1E221MCL6GS 220 10× 8 0.08 165 33 66 2100 PCR1E221MCL1GS 270 8× 12 0.08 202 19 38 3300 PCR1E271MCL1GS 330 10× 10 0.08 247 20 40 3100 PCR1E331MCL1GS 470 10× 12.7 0.08 352 15 30 4100 PCR1E471MCL1GS 68 8 ×7 0.08 71 44 88 1200 PCR1V680MCL1GS 150 ▲ 8× 10 0.08 157 22 44 3100 PCR1V151MCL6GS 150 10× 8 0.08 157 33 66 2100 PCR1V151MCL1GS 220 8× 12 0.08 231 21 42 3300 PCR1V221MCL1GS 270 10× 10 0.08 283 20 40 3100 PCR1V271MCL1GS 330 10× 12.7 0.08 346 16 32 3900 PCR1V331MCL1GS 39 8× 7 0.08 58 45 90 1300 PCR1H390MCL1GS 82 ▲ 8× 10 0.08 123 26 52 2900 PCR1H820MCL6GS 82 10× 8 0.08 123 42 84 1900 PCR1H820MCL1GS 120 △ 8× 12 0.08 180 25 50 2900 PCR1H121MCL2GS 120 10× 10 0.08 180 25 50 3000 PCR1H121MCL1GS 180 10× 12.7 0.08 270 19 38 3500 PCR1H181MCL1GS 22 8 ×7 0.08 41 48 96 1100 PCR1J220MCL1GS 39 8× 10 0.08 73 28 56 2700 PCR1J390MCL1GS 0.08 88 47 94 1800 PCR1J470MCL1GS 47 10× 8 56 8× 12 0.08 105 27 54 2900 PCR1J560MCL1GS 68 10×10 0.08 128 28 56 2800 PCR1J680MCL1GS 100 10× 12.7 0.08 189 24 48 3000 PCR1J101MCL1GS 27 8× 10 0.08 64 38 76 1400 PCR1K270MCL1GS 39 8× 12 0.08 93 35 70 1600 PCR1K390MCL1GS 47 10× 10 0.08 112 33 66 1700 PCR1K470MCL1GS 68 10× 12.7 0.08 163 28 56 2100 PCR1K680MCL1GS No marked, 1 will be put at 12th digit of type numbering system. : In this case, 2 will be put at 12th digit of type numbering system. : In this case, 6 will be put at 12th digit of type numbering system. For taping specifications, recommended land size/soldering by reflow and minimum order quantity, please refer to the Guidelines for Aluminum Electrolytic Capacitors. CAT.8100K