UCJ1A330MCL

ALUMINUM ELECTROLYTIC CAPACITORS CJ Chip Type, High Reliability. Low temperature ESR specification. series Chip type, high temperature range, for +125°C use. Added ESR specification after the test at – 40°C (φ6.3 sizes provide only for the first stage. ) Applicable to automatic mounting machine using carrier tape. Adapted to the RoHS directive (2002/95/EC). CJ Specifications Item Category Temperature Range Rated Voltage Range Rated Capacitance Range Capacitance Tolerance Leakage Current tan δ Added ESR specification at – 40°C UB Performance Characteristics – 40 ~ +125°C 10 ~ 50V 10 ~ 470µF ± 20% at 120Hz, 20°C After 1 minute's application of rated voltage, leakage current is not more than 0.03CV or 4(µA) , whichever is greater. Measurement frequency : 120Hz, Temperature : 20°C Rated voltage (V) tan δ ( MAX.) 10 0.32 16 0.24 10 12 25 0.21 16 8 25 6 35 0.18 35 4 50 0.18 50 4 Measurement frequency : 120Hz Stability at Low Temperature Rated voltage (V) Impedance ratio ZT / Z20 (MAX.) Z– 40°C / Z+20°C Endurance After 2000 hours' application of rated voltage at 125°C, capacitors meet the characteristic requirements listed at right. Capacitance change tan δ Leakage current Within ±30% of initial value 300% or less of intial specified value Initial specified value or less Shelf Life Resistance to soldering heat Marking After storing the capacitors under no load at 125°C for 1000 hours, and after performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they will meet the specified value for endurance characteristics listed above. The capacitors shall be kept on the hot plate maintained at 250°C Capacitance change Within ±10% of initial value for 30 seconds. After removing from the hot plate and restored tan δ Initial specified value or less at room temperature, they meet the characteristic requirements Leakage current Initial specified value or less listed at right. Black print on the case top. Chip Type Series D± 0.5 C±0.2 B±0.2 0.5MAX. Voltage( C : 16V ) (φ6.3 × 8.7) Plastic platform 0.3MAX. Positive A±0.2 A±0.2 Type numbering system (Example : 10V 100µF) UC J 1 A 1 0 1 MCL 1GS Taping code Configuration Capacitance tolerance (±20%) Rated Capacitance (100mF) Rated voltage (10V) Series name Type 1 2 3 4 5 6 7 8 9 10 11 12 13 14 A2 47C CJ Lot No. Voltage( V : 35V ) Trade mark Capacitance f L±0.3 Plastic platform 0.3MAX. D± 0.5 B±0.2 H C±0.2 0.5MAX. (φ8 × 10, φ10 × 10) E Negative Positive A±0.2 A±0.2 f´ Series f Lot No. Capacitance L±0.5 H 16 1C Negative A B C E L H 25 1E A2 100V CJ D L 6.3 ´ 8.7 8 ´ 10 10 ´ 10 2.4 2.9 3.2 6.6 8.3 10.3 6.6 8.3 10.3 2.2 3.1 4.5 8.7 10 10 0.5 ~ 0.8 0.8 ~ 1.1 0.8 ~ 1.1 (mm) Dimensions Cap.(µF) V Code 10 1A E 10 22 33 47 100 220 330 470 100 220 330 470 101 221 331 471 6.3 × 8.7 8 × 10 10 × 10 10 × 10 14 2.0 1.5 1.5 95 6.0 250 4.5 400 4.5 400 6.3 × 8.7 8 × 10 10 × 10 10 × 10 14 2.0 1.5 1.5 95 6.0 250 4.5 400 4.5 400 6.3 × 8.7 6.3 × 8.7 6.3 × 8.7 8 × 10 10 × 10 10 × 10 14 14 14 2.0 1.5 1.5 6.3 × 8.7 95 6.3 × 8.7 95 6.3 × 8.7 95 6.3 × 8.7 6.0 250 10 × 10 4.5 400 10 × 10 4.5 400 35 1V 14 14 14 14 1.5 1.5 95 6.3 × 8.7 95 6.3 × 8.7 8 × 10 95 95 10 × 10 4.5 400 10 × 10 4.5 400 Case size φD× L (mm) 50 1H 14 14 2.0 1.5 1.5 95 95 6.0 200 4.5 330 4.5 330 Rated ripple after Initial torture test ESR Max. ESR (Ω) at -40°C 100kHz, Rated Ripple (mArms) at 125°C 100kHz Frequency coefficient of rated ripple current Frequency Coefficient 50 Hz 0.35 120 Hz 0.50 300 Hz 0.64 1 kHz 0.83 10 kHz~ 1.00 Taping specifications are given in page 24. Recommended land size, soldering by reflow are given in page 25, 26. Please refer to page 3 for the minimum order quantity. CAT.8100V-2