UCJ1H330MCL1GS

ALUMINUM  ELECTROLYTIC  CAPACITORS UCJ Chip Type, High Reliability. Low temperature ESR specification. Chip type, high temperature range, for +125°C use. Added ESR specification after the test at – 40°C (φ6.3 sizes provide only for the first stage. ) Applicable to automatic mounting machine fed with carrier tape. Compliant to the RoHS directive (2011/65/EU,(EU)2015/863). AEC-Q200 Qualified. ow ESR Please contact us for details. UCZ LLong Life UCJ UUB Added ESR specification at –40°C Specifications Item Performance Characteristics Category Temperature Range –40 to +125°C Rated Voltage Range 10 to 50V Rated Capacitance Range 10 to 470µF Capacitance Tolerance ± 20% at 120Hz, 20°C Leakage Current After 1 minute's application of rated voltage at 20°C, leakage current is not more than 0.03CV or 4(µA) , whichever is greater. Measurement frequency : 120Hz at 20°C Rated voltage (V) tan δ (max.) Tangent of loss angle (tan δ) 10 0.32 16 0.24 25 0.21 35 0.18 50 0.18 Measurement frequency : 120Hz Rated voltage (V) Impedance ratio Z(–40°C) / Z(+20°C) ZT / Z20 (max.) Stability at Low Temperature 10 16 25 35 50 12 8 6 4 4 The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 2000 hours at 125°C. Endurance Capacitance change tan δ Leakage current Within ±30% of the initial capacitance value 300% or less than the intial specified value Less than or equal to the initial specified value After storing the capacitors under no load at 125°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above. The capacitors are kept on a hot plate for 30 seconds, Within ±10% of the initial capacitance value Capacitance change which is maintained at 250°C. The capacitors shall meet Less than or equal to the initial specified value tan δ the characteristic requirements listed at right when they Less than or equal to the initial specified value Leakage current are removed from the plate and restored to 20°C. Shelf Life Resistance to soldering heat Black print on the case top. Marking ※ I : Leakage Current (μA), C : Rated Capacitance (μF), V : Rated Voltage (V) Type numbering system (Example : 10V 100µF) Chip Type C±0.2 A±0.2 E A±0.2 B±0.2 φD ±0.5 A2 100V CJ Capacitance 5 6 7 8 9 10 11 12 13 14 Taping code Configuration Capacitance tolerance (±20%) Rated voltage (10V) Series name Positive 0.3max. Series Trade mark 4 Negative Plastic platform Voltage( V : 35V ) 3 Rated capacitance (100µF) H L±0.3 2 A±0.2 E A±0.2 B±0.2 Capacitance (φ8 , φ10) Lot No. C±0.2 0.3max. φD±0.5 A2 47C CJ Series 1 UC J 1 A 1 0 1 MC L 1 GS 0.5max. Plastic platform Voltage( C : 16V ) Lot No. Positive H L±0.5 0.5max. (φ6.3) Negative Type (mm) φD × L A B C E L H 6.3 × 8.7 8 × 10 10 × 10 2.4 2.9 3.2 6.6 8.3 10.3 6.6 8.3 10.3 2.2 3.1 4.5 8.7 10 10 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1 Voltage V Code 10 A 16 C 25 E 35 V 50 H Frequency coefficient of rated ripple current Frequency Coefficient 50 Hz 0.35 120 Hz 0.50 300 Hz 0.64 1 kHz 0.83 10 kHz or more 1.00 Dimension table in next page. CAT.8100M ALUMINUM  ELECTROLYTIC  CAPACITORS UCJ ■ Dimensions Rated Voltage （V） （code） Rated Capacitance （µF） 100 10 （1A） 16 （1C） 25 （1E） 35 （1V） 50 （1H） Case Size φD×L（mm） tan δ Leakage Current （µA） at 20℃ after 1 minute （ ） ESR（Ω）max. （−40℃/100kHz） Initial 14 Rated Ripple （mArms） （125℃/100kHz） Part Number − 95 UCJ1A101MCL1GS after endurance test 6.3× 8.7 0.32 30 220 8× 10 0.32 66 2.0 6.0 250 UCJ1A221MCL1GS 330 10× 10 0.32 99 1.5 4.5 400 UCJ1A331MCL1GS 470 10× 10 0.32 141 1.5 4.5 400 UCJ1A471MCL1GS 47 6.3× 8.7 0.24 22.56 − 95 UCJ1C470MCL1GS 100 8× 10 0.24 48 14 2.0 6.0 250 UCJ1C101MCL1GS 220 10× 10 0.24 105.6 1.5 4.5 400 UCJ1C221MCL1GS 330 10× 10 0.24 158.4 1.5 4.5 400 UCJ1C331MCL1GS 22 6.3× 8.7 0.21 16.5 14 − 95 UCJ1E220MCL1GS 33 6.3× 8.7 0.21 24.75 14 − 95 UCJ1E330MCL1GS 47 6.3× 8.7 0.21 35.25 14 − 95 UCJ1E470MCL1GS 100 8× 10 0.21 75 2.0 6.0 250 UCJ1E101MCL1GS 220 10× 10 0.21 165 1.5 4.5 400 UCJ1E221MCL1GS 330 10× 10 0.21 247.5 1.5 4.5 400 UCJ1E331MCL1GS 10 6.3× 8.7 0.18 10.5 14 − 95 UCJ1V100MCL1GS 22 6.3× 8.7 0.18 23.1 14 − 95 UCJ1V220MCL1GS 33 6.3× 8.7 0.18 34.65 14 − 95 UCJ1V330MCL1GS 47 6.3× 8.7 0.18 49.35 14 − 95 UCJ1V470MCL1GS 100 10× 10 0.18 105 1.5 4.5 400 UCJ1V101MCL1GS 220 10× 10 0.18 231 1.5 4.5 400 UCJ1V221MCL1GS 10 6.3× 8.7 0.18 15 14 − 95 UCJ1H100MCL1GS 22 6.3× 8.7 0.18 33 14 − 95 UCJ1H220MCL1GS 33 8× 10 0.18 49.5 2.0 6.0 200 UCJ1H330MCL1GS 47 10× 10 0.18 70.5 1.5 4.5 330 UCJ1H470MCL1GS 100 10× 10 0.18 1.5 4.5 330 UCJ1H101MCL1GS 150 For taping specifications, recommended land size/soldering by reflow and minimum order quantity, please refer to the Guidelines for Aluminum Electrolytic Capacitors. CAT.8100M