UCJ1H101MCL1GS

ALUMINUM  ELECTROLYTIC  CAPACITORS UCJ Chip Type, High Reliability. Low temperature ESR specification. Chip type, high temperature range, for +125°C use. Added ESR specification after the test at – 40°C (φ6.3 sizes provide only for the first stage. ) Applicable to automatic mounting machine fed with carrier tape. Compliant to the RoHS directive (2011/65/EU,(EU)2015/863). AEC-Q200 compliant. ow ESR Please contact us for details. UCZ LLong Life UCJ Added ESR specification at –40°C UUB Specifications Item Performance Characteristics Category Temperature Range –40 to +125°C Rated Voltage Range 10 to 50V Rated Capacitance Range 10 to 470µF Capacitance Tolerance ± 20% at 120Hz, 20°C Leakage Current After 1 minute's application of rated voltage at 20°C, leakage current is not more than 0.03CV or 4(µA) , whichever is greater. Measurement frequency : 120Hz at 20°C Rated voltage (V) tan δ (MAX.) Tangent of loss angle (tan δ) 10 0.32 16 0.24 25 0.21 35 0.18 50 0.18 Measurement frequency : 120Hz Rated voltage (V) Impedance ratio Z–40°C / Z+20°C ZT / Z20 (MAX.) Stability at Low Temperature 10 16 25 35 50 12 8 6 4 4 Capacitance change tan δ Leakage current The specifications listed at right shall be met when the capacitors are restored to 20°C after the rated voltage is applied for 2000 hours at 125°C. Endurance Within ±30% of the initial capacitance value 300% or less than the intial specified value Less than or equal to the initial specified value After storing the capacitors under no load at 125°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4 clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above. The capacitors are kept on a hot plate for 30 seconds, Within ±10% of the initial capacitance value Capacitance change which is maintained at 250°C. The capacitors shall meet Less than or equal to the initial specified value tan δ the characteristic requirements listed at right when they Less than or equal to the initial specified value Leakage current are removed from the plate and restored to 20°C. Shelf Life Resistance to soldering heat Black print on the case top. Marking Type numbering system (Example : 10V 100µF) Chip Type (φ8 , φ10) C±0.2 Capacitance 7 8 9 10 11 12 13 14 Taping code Configuration Capacitance tolerance (±20%) Rated voltage (10V) Series name H L±0.5 Type (mm) φD × L A±0.2 E A±0.2 B±0.2 φD ±0.5 A2 100V CJ Lot No. 6 Positive 0.3MAX. Series Trade mark 5 Negative Plastic platform Voltage( V : 35V ) 4 Rated capacitance (100µF) H L±0.3 3 A±0.2 E A±0.2 B±0.2 Capacitance Lot No. C±0.2 0.3MAX. φD±0.5 A2 47C CJ Series 2 UC J 1 A 1 0 1 MC L 1 GS 0.5MAX. Plastic platform Voltage( C : 16V ) 1 Positive 0.5MAX. (φ6.3) A B C E L H Negative 6.3 × 8.7 8 × 10 10 × 10 2.4 2.9 3.2 6.6 8.3 10.3 6.6 8.3 10.3 2.2 3.1 4.5 8.7 10 10 0.5 to 0.8 0.8 to 1.1 0.8 to 1.1 Voltage V Code 10 A 16 C 25 E 35 V 50 H Dimensions Cap.(µF) 10 22 33 47 100 220 330 470 10 1A V Code 100 220 330 470 101 221 331 471 6.3 × 8.7 8 × 10 10 × 10 10 × 10 14 2.0 1.5 1.5 16 1C 95 6.0 250 4.5 400 4.5 400 6.3 × 8.7 8 × 10 10 × 10 10 × 10 14 2.0 1.5 1.5 25 1E 95 6.0 250 4.5 400 4.5 400 6.3 × 8.7 6.3 × 8.7 6.3 × 8.7 8 × 10 10 × 10 10 × 10 14 14 14 2.0 1.5 1.5 6.3 × 8.7 95 6.3 × 8.7 95 6.3 × 8.7 95 6.3 × 8.7 6.0 250 10 × 10 4.5 400 10 × 10 4.5 400 35 1V 14 14 14 14 1.5 1.5 95 6.3 × 8.7 95 6.3 × 8.7 8 × 10 95 95 10 × 10 4.5 400 10 × 10 4.5 400 Case size φD× L (mm) 50 1H 14 14 2.0 1.5 1.5 95 95 6.0 200 4.5 330 4.5 330 after Initial endurance test ESR Rated ripple Max. ESR (Ω) at -40°C 100kHz, Rated ripple current (mArms) at 125°C 100kHz Frequency coefficient of rated ripple current Frequency Coefficient 50 Hz 0.35 120 Hz 0.50 300 Hz 0.64 1 kHz 0.83 10 kHz or more 1.00 162 Taping specifications are given in page 23. Recommended land size, soldering by reflow are given in page 18, 19. Please refer to page 3 for the minimum order quantity.